[thirdparty/u-boot.git] / src / arm64 / qcom / msm8916-longcheer-l8150.dts

// SPDX-License-Identifier: GPL-2.0-only

/dts-v1/;

#include "msm8916-pm8916.dtsi"
#include "msm8916-modem-qdsp6.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/leds/common.h>

/ {
	model = "Longcheer L8150";
	compatible = "longcheer,l8150", "qcom,msm8916-v1-qrd/9-v1", "qcom,msm8916";
	chassis-type = "handset";

	aliases {
		mmc0 = &sdhc_1; /* eMMC */
		mmc1 = &sdhc_2; /* SD card */
		serial0 = &blsp_uart2;
	};

	chosen {
		stdout-path = "serial0";
	};

	/*
	 * For some reason, the signed wcnss firmware is not relocatable.
	 * It must be loaded at 0x8b600000. Unfortunately, this also means that
	 * mpss_mem does not fit when loaded to the typical address at 0x86800000.
	 *
	 * Load wcnss_mem to the fixed address and relocate mpss_mem to the next
	 * working higher address. For some reason the modem firmware does not
	 * boot when placed at 0x8a800000 to 0x8e800000.
	 */
	reserved-memory {
		/delete-node/ mpss@86800000;
		/delete-node/ wcnss;

		wcnss_mem: wcnss@8b600000 {
			reg = <0x0 0x8b600000 0x0 0x600000>;
			no-map;
		};

		mpss_mem: mpss@8e800000 {
			reg = <0x0 0x8e800000 0x0 0x5000000>;
			no-map;
		};
	};

	battery: battery {
		compatible = "simple-battery";
		voltage-min-design-microvolt = <3400000>;
		voltage-max-design-microvolt = <4350000>;
		energy-full-design-microwatt-hours = <9500000>;
		charge-full-design-microamp-hours = <2500000>;

		ocv-capacity-celsius = <25>;
		ocv-capacity-table-0 = <4330000 100>, <4265000 95>,
			<4208000 90>, <4153000 85>, <4100000 80>, <4049000 75>,
			<4001000 70>, <3962000 65>, <3919000 60>, <3872000 55>,
			<3839000 50>, <3817000 45>, <3798000 40>, <3783000 35>,
			<3767000 30>, <3747000 25>, <3729000 20>, <3709000 16>,
			<3688000 13>, <3681000 11>, <3680000 10>, <3679000 9>,
			<3677000 8>, <3674000 7>, <3666000 6>, <3641000 5>,
			<3597000 4>, <3537000 3>, <3457000 2>, <3336000 1>,
			<3000000 0>;
	};

	gpio-keys {
		compatible = "gpio-keys";

		pinctrl-names = "default";
		pinctrl-0 = <&gpio_keys_default>;

		label = "GPIO Buttons";

		button-volume-up {
			label = "Volume Up";
			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
			linux,code = <KEY_VOLUMEUP>;
		};
	};

	reg_ctp: regulator-ctp {
		compatible = "regulator-fixed";
		regulator-name = "ctp";

		regulator-min-microvolt = <2800000>;
		regulator-max-microvolt = <2800000>;

		gpio = <&tlmm 17 GPIO_ACTIVE_HIGH>;
		enable-active-high;

		pinctrl-names = "default";
		pinctrl-0 = <&ctp_pwr_en_default>;
	};

	flash-led-controller {
		compatible = "sgmicro,sgm3140";
		flash-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
		enable-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;

		pinctrl-names = "default";
		pinctrl-0 = <&camera_flash_default>;

		flash_led: led {
			function = LED_FUNCTION_FLASH;
			color = <LED_COLOR_ID_WHITE>;
			flash-max-timeout-us = <250000>;
		};
	};
};

&blsp_i2c1 {
	status = "okay";

	led-controller@45 {
		compatible = "awinic,aw2013";
		reg = <0x45>;
		#address-cells = <1>;
		#size-cells = <0>;

		vcc-supply = <&pm8916_l17>;
		vio-supply = <&pm8916_l6>;

		led@0 {
			reg = <0>;
			led-max-microamp = <5000>;
			function = LED_FUNCTION_INDICATOR;
			color = <LED_COLOR_ID_RED>;
		};

		led@1 {
			reg = <1>;
			led-max-microamp = <5000>;
			function = LED_FUNCTION_INDICATOR;
			color = <LED_COLOR_ID_GREEN>;
		};

		led@2 {
			reg = <2>;
			led-max-microamp = <5000>;
			function = LED_FUNCTION_INDICATOR;
			color = <LED_COLOR_ID_BLUE>;
		};
	};
};

&blsp_i2c2 {
	status = "okay";

	accelerometer@10 {
		compatible = "bosch,bmc156_accel";
		reg = <0x10>;

		/*
		 * For some reason the interrupt line is usually not connected
		 * to the BMC156. However, there are two pads next to the chip
		 * that can be shorted to make it work if needed.
		 *
		 * interrupt-parent = <&tlmm>;
		 * interrupts = <116 IRQ_TYPE_EDGE_RISING>;
		 */

		pinctrl-names = "default";
		pinctrl-0 = <&accel_int_default>;

		vdd-supply = <&pm8916_l17>;
		vddio-supply = <&pm8916_l6>;

		mount-matrix = "0", "1", "0",
			      "-1", "0", "0",
			       "0", "0", "1";
	};

	magnetometer@12 {
		compatible = "bosch,bmc156_magn";
		reg = <0x12>;

		interrupt-parent = <&tlmm>;
		interrupts = <113 IRQ_TYPE_EDGE_RISING>;

		pinctrl-names = "default";
		pinctrl-0 = <&magn_int_default>;

		vdd-supply = <&pm8916_l17>;
		vddio-supply = <&pm8916_l6>;
	};

	light-sensor@23 {
		compatible = "liteon,ltr559";
		reg = <0x23>;
		proximity-near-level = <75>;

		interrupt-parent = <&tlmm>;
		interrupts = <115 IRQ_TYPE_EDGE_FALLING>;

		pinctrl-names = "default";
		pinctrl-0 = <&light_int_default>;

		vdd-supply = <&pm8916_l17>;
		vddio-supply = <&pm8916_l6>;
	};

	gyroscope@68 {
		compatible = "bosch,bmg160";
		reg = <0x68>;

		interrupt-parent = <&tlmm>;
		interrupts = <23 IRQ_TYPE_EDGE_RISING>,
			     <22 IRQ_TYPE_EDGE_RISING>;

		pinctrl-names = "default";
		pinctrl-0 = <&gyro_int_default>;

		vdd-supply = <&pm8916_l17>;
		vddio-supply = <&pm8916_l6>;
	};
};

&blsp_i2c5 {
	status = "okay";

	rmi4@20 {
		compatible = "syna,rmi4-i2c";
		reg = <0x20>;
		#address-cells = <1>;
		#size-cells = <0>;

		interrupt-parent = <&tlmm>;
		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;

		vdd-supply = <&reg_ctp>;
		vio-supply = <&pm8916_l6>;

		pinctrl-names = "default";
		pinctrl-0 = <&tp_int_default>;

		syna,startup-delay-ms = <10>;

		rmi4-f01@1 {
			reg = <0x1>;
			syna,nosleep-mode = <1>; /* Allow sleeping */
		};

		rmi4-f12@12 {
			reg = <0x12>;
			syna,sensor-type = <1>; /* Touchscreen */
		};
	};
};

&blsp_uart2 {
	status = "okay";
};

&pm8916_bms {
	status = "okay";

	monitored-battery = <&battery>;
	power-supplies = <&pm8916_charger>;
};

&pm8916_charger {
	status = "okay";

	monitored-battery = <&battery>;

	qcom,fast-charge-safe-current = <900000>;
	qcom,fast-charge-safe-voltage = <4300000>;
};

&pm8916_codec {
	qcom,micbias-lvl = <2800>;
	qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
	qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
	qcom,hphl-jack-type-normally-open;
};

&pm8916_resin {
	status = "okay";
	linux,code = <KEY_VOLUMEDOWN>;
};

&pm8916_rpm_regulators {
	pm8916_l17: l17 {
		regulator-min-microvolt = <2850000>;
		regulator-max-microvolt = <2850000>;
	};
};

&pm8916_vib {
	status = "okay";
};

&sdhc_1 {
	status = "okay";
};

&sdhc_2 {
	status = "okay";
	non-removable;
};

&sound {
	audio-routing =
		"AMIC1", "MIC BIAS Internal1",
		"AMIC2", "MIC BIAS Internal2",
		"AMIC3", "MIC BIAS Internal3";
};

&usb {
	status = "okay";
	dr_mode = "peripheral";
	extcon = <&pm8916_charger>;
};

&usb_hs_phy {
	extcon = <&pm8916_charger>;
};

&venus {
	status = "okay";
};

&venus_mem {
	status = "okay";
};

&wcnss {
	status = "okay";
};

&wcnss_iris {
	compatible = "qcom,wcn3620";
};

&wcnss_mem {
	status = "okay";
};

&tlmm {
	accel_int_default: accel-int-default-state {
		pins = "gpio116";
		function = "gpio";

		drive-strength = <2>;
		bias-disable;
	};

	camera_flash_default: camera-flash-default-state {
		pins = "gpio31", "gpio32";
		function = "gpio";

		drive-strength = <2>;
		bias-disable;
	};

	ctp_pwr_en_default: ctp-pwr-en-default-state {
		pins = "gpio17";
		function = "gpio";

		drive-strength = <2>;
		bias-disable;
	};

	gpio_keys_default: gpio-keys-default-state {
		pins = "gpio107";
		function = "gpio";

		drive-strength = <2>;
		bias-pull-up;
	};

	gyro_int_default: gyro-int-default-state {
		pins = "gpio22", "gpio23";
		function = "gpio";

		drive-strength = <2>;
		bias-disable;
	};

	light_int_default: light-int-default-state {
		pins = "gpio115";
		function = "gpio";

		drive-strength = <2>;
		bias-disable;
	};

	magn_int_default: magn-int-default-state {
		pins = "gpio113";
		function = "gpio";

		drive-strength = <2>;
		bias-disable;
	};

	tp_int_default: tp-int-default-state {
		pins = "gpio13";
		function = "gpio";

		drive-strength = <2>;
		bias-disable;
	};
};
Commit	Line	Data
53633a89 TR	1	// SPDX-License-Identifier: GPL-2.0-only
	2
	3	/dts-v1/;
	4
	5	#include "msm8916-pm8916.dtsi"
93743d24 TR	6	#include "msm8916-modem-qdsp6.dtsi"
93743d24 TR	7
53633a89 TR	8	#include <dt-bindings/gpio/gpio.h>
	9	#include <dt-bindings/input/input.h>
	10	#include <dt-bindings/interrupt-controller/irq.h>
	11	#include <dt-bindings/leds/common.h>
	12
	13	/ {
	14	model = "Longcheer L8150";
	15	compatible = "longcheer,l8150", "qcom,msm8916-v1-qrd/9-v1", "qcom,msm8916";
	16	chassis-type = "handset";
	17
	18	aliases {
	19	mmc0 = &sdhc_1; /* eMMC */
	20	mmc1 = &sdhc_2; /* SD card */
	21	serial0 = &blsp_uart2;
	22	};
	23
	24	chosen {
	25	stdout-path = "serial0";
	26	};
	27
	28	/*
	29	* For some reason, the signed wcnss firmware is not relocatable.
93743d24 TR	30	* It must be loaded at 0x8b600000. Unfortunately, this also means that
	31	* mpss_mem does not fit when loaded to the typical address at 0x86800000.
	32	*
	33	* Load wcnss_mem to the fixed address and relocate mpss_mem to the next
	34	* working higher address. For some reason the modem firmware does not
	35	* boot when placed at 0x8a800000 to 0x8e800000.
53633a89 TR	36	*/
53633a89 TR	37	reserved-memory {
93743d24	38	/delete-node/ mpss@86800000;
53633a89 TR	39	/delete-node/ wcnss;
	40
	41	wcnss_mem: wcnss@8b600000 {
	42	reg = <0x0 0x8b600000 0x0 0x600000>;
	43	no-map;
	44	};
93743d24 TR	45
	46	mpss_mem: mpss@8e800000 {
	47	reg = <0x0 0x8e800000 0x0 0x5000000>;
	48	no-map;
	49	};
	50	};
	51
	52	battery: battery {
	53	compatible = "simple-battery";
	54	voltage-min-design-microvolt = <3400000>;
	55	voltage-max-design-microvolt = <4350000>;
	56	energy-full-design-microwatt-hours = <9500000>;
	57	charge-full-design-microamp-hours = <2500000>;
	58
	59	ocv-capacity-celsius = <25>;
	60	ocv-capacity-table-0 = <4330000 100>, <4265000 95>,
	61	<4208000 90>, <4153000 85>, <4100000 80>, <4049000 75>,
	62	<4001000 70>, <3962000 65>, <3919000 60>, <3872000 55>,
	63	<3839000 50>, <3817000 45>, <3798000 40>, <3783000 35>,
	64	<3767000 30>, <3747000 25>, <3729000 20>, <3709000 16>,
	65	<3688000 13>, <3681000 11>, <3680000 10>, <3679000 9>,
	66	<3677000 8>, <3674000 7>, <3666000 6>, <3641000 5>,
	67	<3597000 4>, <3537000 3>, <3457000 2>, <3336000 1>,
	68	<3000000 0>;
53633a89 TR	69	};
	70
	71	gpio-keys {
	72	compatible = "gpio-keys";
	73
	74	pinctrl-names = "default";
	75	pinctrl-0 = <&gpio_keys_default>;
	76
	77	label = "GPIO Buttons";
	78
	79	button-volume-up {
	80	label = "Volume Up";
	81	gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
	82	linux,code = <KEY_VOLUMEUP>;
	83	};
	84	};
	85
	86	reg_ctp: regulator-ctp {
	87	compatible = "regulator-fixed";
	88	regulator-name = "ctp";
	89
	90	regulator-min-microvolt = <2800000>;
	91	regulator-max-microvolt = <2800000>;
	92
	93	gpio = <&tlmm 17 GPIO_ACTIVE_HIGH>;
	94	enable-active-high;
	95
	96	pinctrl-names = "default";
	97	pinctrl-0 = <&ctp_pwr_en_default>;
	98	};
	99
	100	flash-led-controller {
	101	compatible = "sgmicro,sgm3140";
	102	flash-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
	103	enable-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
	104
	105	pinctrl-names = "default";
	106	pinctrl-0 = <&camera_flash_default>;
	107
	108	flash_led: led {
	109	function = LED_FUNCTION_FLASH;
	110	color = <LED_COLOR_ID_WHITE>;
	111	flash-max-timeout-us = <250000>;
	112	};
	113	};
	114	};
	115
	116	&blsp_i2c1 {
	117	status = "okay";
	118
	119	led-controller@45 {
	120	compatible = "awinic,aw2013";
	121	reg = <0x45>;
	122	#address-cells = <1>;
	123	#size-cells = <0>;
	124
	125	vcc-supply = <&pm8916_l17>;
93743d24	126	vio-supply = <&pm8916_l6>;
53633a89 TR	127
	128	led@0 {
	129	reg = <0>;
	130	led-max-microamp = <5000>;
	131	function = LED_FUNCTION_INDICATOR;
	132	color = <LED_COLOR_ID_RED>;
	133	};
	134
	135	led@1 {
	136	reg = <1>;
	137	led-max-microamp = <5000>;
	138	function = LED_FUNCTION_INDICATOR;
	139	color = <LED_COLOR_ID_GREEN>;
	140	};
	141
	142	led@2 {
	143	reg = <2>;
	144	led-max-microamp = <5000>;
	145	function = LED_FUNCTION_INDICATOR;
	146	color = <LED_COLOR_ID_BLUE>;
	147	};
	148	};
	149	};
	150
	151	&blsp_i2c2 {
	152	status = "okay";
	153
	154	accelerometer@10 {
	155	compatible = "bosch,bmc156_accel";
	156	reg = <0x10>;
	157
	158	/*
	159	* For some reason the interrupt line is usually not connected
	160	* to the BMC156. However, there are two pads next to the chip
	161	* that can be shorted to make it work if needed.
	162	*
	163	* interrupt-parent = <&tlmm>;
	164	* interrupts = <116 IRQ_TYPE_EDGE_RISING>;
	165	*/
	166
	167	pinctrl-names = "default";
	168	pinctrl-0 = <&accel_int_default>;
	169
	170	vdd-supply = <&pm8916_l17>;
	171	vddio-supply = <&pm8916_l6>;
	172
	173	mount-matrix = "0", "1", "0",
	174	"-1", "0", "0",
	175	"0", "0", "1";
	176	};
	177
	178	magnetometer@12 {
	179	compatible = "bosch,bmc156_magn";
	180	reg = <0x12>;
	181
	182	interrupt-parent = <&tlmm>;
	183	interrupts = <113 IRQ_TYPE_EDGE_RISING>;
	184
	185	pinctrl-names = "default";
	186	pinctrl-0 = <&magn_int_default>;
	187
	188	vdd-supply = <&pm8916_l17>;
	189	vddio-supply = <&pm8916_l6>;
	190	};
191
192	light-sensor@23 {
193	compatible = "liteon,ltr559";
194	reg = <0x23>;
195	proximity-near-level = <75>;
196
197	interrupt-parent = <&tlmm>;
198	interrupts = <115 IRQ_TYPE_EDGE_FALLING>;
199
200	pinctrl-names = "default";
201	pinctrl-0 = <&light_int_default>;
202
203	vdd-supply = <&pm8916_l17>;
204	vddio-supply = <&pm8916_l6>;
205	};
206
207	gyroscope@68 {
208	compatible = "bosch,bmg160";
209	reg = <0x68>;
210
211	interrupt-parent = <&tlmm>;
212	interrupts = <23 IRQ_TYPE_EDGE_RISING>,
213	<22 IRQ_TYPE_EDGE_RISING>;
214
215	pinctrl-names = "default";
216	pinctrl-0 = <&gyro_int_default>;
217
218	vdd-supply = <&pm8916_l17>;
219	vddio-supply = <&pm8916_l6>;
220	};
221	};
222
223	&blsp_i2c5 {
224	status = "okay";
225
226	rmi4@20 {
227	compatible = "syna,rmi4-i2c";
228	reg = <0x20>;
229	#address-cells = <1>;
230	#size-cells = <0>;
231
232	interrupt-parent = <&tlmm>;
233	interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
234
235	vdd-supply = <&reg_ctp>;
236	vio-supply = <&pm8916_l6>;
237
238	pinctrl-names = "default";
239	pinctrl-0 = <&tp_int_default>;
240
241	syna,startup-delay-ms = <10>;
242
243	rmi4-f01@1 {
244	reg = <0x1>;
245	syna,nosleep-mode = <1>; /* Allow sleeping */
246	};
247
248	rmi4-f12@12 {
249	reg = <0x12>;
250	syna,sensor-type = <1>; /* Touchscreen */
251	};
252	};
253	};
254
255	&blsp_uart2 {
256	status = "okay";
257	};
258
93743d24 TR	259	&pm8916_bms {
	260	status = "okay";
	261
	262	monitored-battery = <&battery>;
	263	power-supplies = <&pm8916_charger>;
	264	};
	265
	266	&pm8916_charger {
	267	status = "okay";
	268
	269	monitored-battery = <&battery>;
	270
	271	qcom,fast-charge-safe-current = <900000>;
	272	qcom,fast-charge-safe-voltage = <4300000>;
	273	};
	274
	275	&pm8916_codec {
	276	qcom,micbias-lvl = <2800>;
	277	qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
	278	qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
	279	qcom,hphl-jack-type-normally-open;
	280	};
	281
53633a89 TR	282	&pm8916_resin {
	283	status = "okay";
	284	linux,code = <KEY_VOLUMEDOWN>;
	285	};
	286
	287	&pm8916_rpm_regulators {
	288	pm8916_l17: l17 {
	289	regulator-min-microvolt = <2850000>;
	290	regulator-max-microvolt = <2850000>;
	291	};
	292	};
	293
53633a89 TR	294	&pm8916_vib {
	295	status = "okay";
	296	};
	297
	298	&sdhc_1 {
	299	status = "okay";
	300	};
	301
	302	&sdhc_2 {
	303	status = "okay";
	304	non-removable;
	305	};
	306
93743d24 TR	307	&sound {
	308	audio-routing =
	309	"AMIC1", "MIC BIAS Internal1",
	310	"AMIC2", "MIC BIAS Internal2",
	311	"AMIC3", "MIC BIAS Internal3";
	312	};
	313
53633a89 TR	314	&usb {
	315	status = "okay";
	316	dr_mode = "peripheral";
93743d24	317	extcon = <&pm8916_charger>;
53633a89 TR	318	};
	319
	320	&usb_hs_phy {
93743d24	321	extcon = <&pm8916_charger>;
53633a89 TR	322	};
	323
	324	&venus {
	325	status = "okay";
	326	};
	327
	328	&venus_mem {
	329	status = "okay";
	330	};
	331
	332	&wcnss {
	333	status = "okay";
	334	};
	335
	336	&wcnss_iris {
	337	compatible = "qcom,wcn3620";
	338	};
	339
	340	&wcnss_mem {
	341	status = "okay";
	342	};
	343
	344	&tlmm {
	345	accel_int_default: accel-int-default-state {
	346	pins = "gpio116";
	347	function = "gpio";
	348
	349	drive-strength = <2>;
	350	bias-disable;
	351	};
	352
	353	camera_flash_default: camera-flash-default-state {
	354	pins = "gpio31", "gpio32";
	355	function = "gpio";
	356
	357	drive-strength = <2>;
	358	bias-disable;
	359	};
	360
	361	ctp_pwr_en_default: ctp-pwr-en-default-state {
	362	pins = "gpio17";
	363	function = "gpio";
	364
	365	drive-strength = <2>;
	366	bias-disable;
	367	};
	368
	369	gpio_keys_default: gpio-keys-default-state {
	370	pins = "gpio107";
	371	function = "gpio";
	372
	373	drive-strength = <2>;
	374	bias-pull-up;
	375	};
	376
	377	gyro_int_default: gyro-int-default-state {
	378	pins = "gpio22", "gpio23";
	379	function = "gpio";
	380
	381	drive-strength = <2>;
	382	bias-disable;
	383	};
	384
	385	light_int_default: light-int-default-state {
386	pins = "gpio115";
387	function = "gpio";
388
389	drive-strength = <2>;
390	bias-disable;
391	};
392
393	magn_int_default: magn-int-default-state {
394	pins = "gpio113";
395	function = "gpio";
396
397	drive-strength = <2>;
398	bias-disable;
399	};
400
401	tp_int_default: tp-int-default-state {
402	pins = "gpio13";
403	function = "gpio";
404
405	drive-strength = <2>;
406	bias-disable;
407	};
408	};