Update Release Notes Sections

[thirdparty/squid.git] / src / cf.data.pre

#
# $Id: cf.data.pre,v 1.502 2008/02/12 00:05:11 amosjeffries Exp $
#
# SQUID Web Proxy Cache		http://www.squid-cache.org/
# ----------------------------------------------------------
#
#  Squid is the result of efforts by numerous individuals from
#  the Internet community; see the CONTRIBUTORS file for full
#  details.   Many organizations have provided support for Squid's
#  development; see the SPONSORS file for full details.  Squid is
#  Copyrighted (C) 2000 by the Regents of the University of
#  California; see the COPYRIGHT file for full details.  Squid
#  incorporates software developed and/or copyrighted by other
#  sources; see the CREDITS file for full details.
#
#  This program is free software; you can redistribute it and/or modify
#  it under the terms of the GNU General Public License as published by
#  the Free Software Foundation; either version 2 of the License, or
#  (at your option) any later version.
#
#  This program is distributed in the hope that it will be useful,
#  but WITHOUT ANY WARRANTY; without even the implied warranty of
#  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
#  GNU General Public License for more details.
#
#  You should have received a copy of the GNU General Public License
#  along with this program; if not, write to the Free Software
#  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111, USA.
#

COMMENT_START
	WELCOME TO SQUID @VERSION@
	----------------------------

	This is the default Squid configuration file. You may wish
	to look at the Squid home page (http://www.squid-cache.org/)
	for the FAQ and other documentation.

	The default Squid config file shows what the defaults for
	various options happen to be.  If you don't need to change the
	default, you shouldn't uncomment the line.  Doing so may cause
	run-time problems.  In some cases "none" refers to no default
	setting at all, while in other cases it refers to a valid
	option - the comments for that keyword indicate if this is the
	case.

COMMENT_END

COMMENT_START
  Configuration options can be included using the "include" directive.
  Include takes a list of files to include. Quoting and wildcards is
  supported.

  For example,

  include /path/to/included/file/squid.acl.config

  Includes can be nested up to a hard-coded depth of 16 levels.
  This arbitrary restriction is to prevent recursive include references
  from causing Squid entering an infinite loop whilst trying to load
  configuration files.
COMMENT_END

COMMENT_START
 OPTIONS FOR AUTHENTICATION
 -----------------------------------------------------------------------------
COMMENT_END

NAME: auth_param
TYPE: authparam
LOC: Config.authConfiguration
DEFAULT: none
DOC_START
	This is used to define parameters for the various authentication
	schemes supported by Squid.

	format: auth_param scheme parameter [setting]

	The order in which authentication schemes are presented to the client is
	dependent on the order the scheme first appears in config file. IE
	has a bug (it's not RFC 2617 compliant) in that it will use the basic
	scheme if basic is the first entry presented, even if more secure
	schemes are presented. For now use the order in the recommended
	settings section below. If other browsers have difficulties (don't
	recognize the schemes offered even if you are using basic) either
	put basic first, or disable the other schemes (by commenting out their
	program entry).

	Once an authentication scheme is fully configured, it can only be
	shutdown by shutting squid down and restarting. Changes can be made on
	the fly and activated with a reconfigure. I.E. You can change to a
	different helper, but not unconfigure the helper completely.

	Please note that while this directive defines how Squid processes
	authentication it does not automatically activate authentication.
	To use authentication you must in addition make use of ACLs based
	on login name in http_access (proxy_auth, proxy_auth_regex or
	external with %LOGIN used in the format tag). The browser will be
	challenged for authentication on the first such acl encountered
	in http_access processing and will also be re-challenged for new
	login credentials if the request is being denied by a proxy_auth
	type acl.

	WARNING: authentication can't be used in a transparently intercepting
	proxy as the client then thinks it is talking to an origin server and
	not the proxy. This is a limitation of bending the TCP/IP protocol to
	transparently intercepting port 80, not a limitation in Squid.
	Ports flagged 'transparent', 'intercept', or 'tproxy' have authentication
	disabled.

	=== Parameters for the basic scheme follow. ===

	"program" cmdline
	Specify the command for the external authenticator.  Such a program
	reads a line containing "username password" and replies "OK" or
	"ERR" in an endless loop. "ERR" responses may optionally be followed
	by a error description available as %m in the returned error page.
	If you use an authenticator, make sure you have 1 acl of type proxy_auth.

	By default, the basic authentication scheme is not used unless a
	program is specified.

	If you want to use the traditional NCSA proxy authentication, set
	this line to something like

	auth_param basic program @DEFAULT_PREFIX@/libexec/ncsa_auth @DEFAULT_PREFIX@/etc/passwd

	"children" numberofchildren
	The number of authenticator processes to spawn. If you start too few
	Squid will have to wait for them to process a backlog of credential
	verifications, slowing it down. When password verifications are
	done via a (slow) network you are likely to need lots of
	authenticator processes.
	auth_param basic children 5

	"concurrency" concurrency
	The number of concurrent requests the helper can process.
	The default of 0 is used for helpers who only supports
	one request at a time. Setting this changes the protocol used to
	include a channel number first on the request/response line, allowing
	multiple requests to be sent to the same helper in parallell without
	wating for the response.
	Must not be set unless it's known the helper supports this.
	auth_param basic concurrency 0

	"realm" realmstring
	Specifies the realm name which is to be reported to the
	client for the basic proxy authentication scheme (part of
	the text the user will see when prompted their username and
	password). There is no default.
	auth_param basic realm Squid proxy-caching web server

	"credentialsttl" timetolive
	Specifies how long squid assumes an externally validated
	username:password pair is valid for - in other words how
	often the helper program is called for that user. Set this
	low to force revalidation with short lived passwords.  Note
	setting this high does not impact your susceptibility
	to replay attacks unless you are using an one-time password
	system (such as SecureID).  If you are using such a system,
	you will be vulnerable to replay attacks unless you also
	use the max_user_ip ACL in an http_access rule.

	"casesensitive" on|off
	Specifies if usernames are case sensitive. Most user databases are
	case insensitive allowing the same username to be spelled using both
	lower and upper case letters, but some are case sensitive. This
	makes a big difference for user_max_ip ACL processing and similar.
	auth_param basic casesensitive off

	=== Parameters for the digest scheme follow ===

	"program" cmdline
	Specify the command for the external authenticator.  Such
	a program reads a line containing "username":"realm" and
	replies with the appropriate H(A1) value hex encoded or
	ERR if the user (or his H(A1) hash) does not exists.
	See rfc 2616 for the definition of H(A1).
	"ERR" responses may optionally be followed by a error description
	available as %m in the returned error page.

	By default, the digest authentication scheme is not used unless a
	program is specified.

	If you want to use a digest authenticator, set this line to
	something like

	auth_param digest program @DEFAULT_PREFIX@/bin/digest_auth_pw @DEFAULT_PREFIX@/etc/digpass

	"children" numberofchildren
	The number of authenticator processes to spawn (no default).
	If you start too few Squid will have to wait for them to
	process a backlog of H(A1) calculations, slowing it down.
	When the H(A1) calculations are done via a (slow) network
	you are likely to need lots of authenticator processes.
	auth_param digest children 5

	"realm" realmstring
	Specifies the realm name which is to be reported to the
	client for the digest proxy authentication scheme (part of
	the text the user will see when prompted their username and
	password). There is no default.
	auth_param digest realm Squid proxy-caching web server

	"nonce_garbage_interval" timeinterval
	Specifies the interval that nonces that have been issued
	to client_agent's are checked for validity.

	"nonce_max_duration" timeinterval
	Specifies the maximum length of time a given nonce will be
	valid for.

	"nonce_max_count" number
	Specifies the maximum number of times a given nonce can be
	used.

	"nonce_strictness" on|off
	Determines if squid requires strict increment-by-1 behavior
	for nonce counts, or just incrementing (off - for use when
	useragents generate nonce counts that occasionally miss 1
	(ie, 1,2,4,6)). Default off.

	"check_nonce_count" on|off
	This directive if set to off can disable the nonce count check
	completely to work around buggy digest qop implementations in
	certain mainstream browser versions. Default on to check the
	nonce count to protect from authentication replay attacks.

	"post_workaround" on|off
	This is a workaround to certain buggy browsers who sends
	an incorrect request digest in POST requests when reusing
	the same nonce as acquired earlier on a GET request.

	=== NTLM scheme options follow ===

	"program" cmdline
	Specify the command for the external NTLM authenticator.
	Such a program reads exchanged NTLMSSP packets with
	the browser via Squid until authentication is completed.
	If you use an NTLM authenticator, make sure you have 1 acl
	of type proxy_auth.  By default, the NTLM authenticator_program
	is not used.

	auth_param ntlm program @DEFAULT_PREFIX@/bin/ntlm_auth

	"children" numberofchildren
	The number of authenticator processes to spawn (no default).
	If you start too few Squid will have to wait for them to
	process a backlog of credential verifications, slowing it
	down. When credential verifications are done via a (slow)
	network you are likely to need lots of authenticator
	processes.

	auth_param ntlm children 5

	"keep_alive" on|off
	If you experience problems with PUT/POST requests when using the
	Negotiate authentication scheme then you can try setting this to
	off. This will cause Squid to forcibly close the connection on
	the initial requests where the browser asks which schemes are
	supported by the proxy.

	auth_param ntlm keep_alive on

	=== Options for configuring the NEGOTIATE auth-scheme follow ===

	"program" cmdline
	Specify the command for the external Negotiate authenticator.
	This protocol is used in Microsoft Active-Directory enabled setups with
	the Microsoft Internet Explorer or Mozilla Firefox browsers.
	Its main purpose is to exchange credentials with the Squid proxy
	using the Kerberos mechanisms.
	If you use a Negotiate authenticator, make sure you have at least one acl
	of type proxy_auth active.  By default, the negotiate authenticator_program
	is not used.
	The only supported program for this role is the ntlm_auth
	program distributed as part of Samba, version 4 or later.

	auth_param negotiate program @DEFAULT_PREFIX@/bin/ntlm_auth --helper-protocol=gss-spnego

	"children" numberofchildren
	The number of authenticator processes to spawn (no default).
	If you start too few Squid will have to wait for them to
	process a backlog of credential verifications, slowing it
	down. When crendential verifications are done via a (slow)
	network you are likely to need lots of authenticator
	processes.
	auth_param negotiate children 5

	"keep_alive" on|off
	If you experience problems with PUT/POST requests when using the
	Negotiate authentication scheme then you can try setting this to
	off. This will cause Squid to forcibly close the connection on
	the initial requests where the browser asks which schemes are
	supported by the proxy.

	auth_param negotiate keep_alive on

NOCOMMENT_START
#Recommended minimum configuration per scheme:
#auth_param negotiate program <uncomment and complete this line to activate>
#auth_param negotiate children 5
#auth_param negotiate keep_alive on
#auth_param ntlm program <uncomment and complete this line to activate>
#auth_param ntlm children 5
#auth_param ntlm keep_alive on
#auth_param digest program <uncomment and complete this line>
#auth_param digest children 5
#auth_param digest realm Squid proxy-caching web server
#auth_param digest nonce_garbage_interval 5 minutes
#auth_param digest nonce_max_duration 30 minutes
#auth_param digest nonce_max_count 50
#auth_param basic program <uncomment and complete this line>
#auth_param basic children 5
#auth_param basic realm Squid proxy-caching web server
#auth_param basic credentialsttl 2 hours
NOCOMMENT_END
DOC_END

NAME: authenticate_cache_garbage_interval
TYPE: time_t
DEFAULT: 1 hour
LOC: Config.authenticateGCInterval
DOC_START
	The time period between garbage collection across the username cache.
	This is a tradeoff between memory utilization (long intervals - say
	2 days) and CPU (short intervals - say 1 minute). Only change if you
	have good reason to.
DOC_END

NAME: authenticate_ttl
TYPE: time_t
DEFAULT: 1 hour
LOC: Config.authenticateTTL
DOC_START
	The time a user & their credentials stay in the logged in
	user cache since their last request. When the garbage
	interval passes, all user credentials that have passed their
	TTL are removed from memory.
DOC_END

NAME: authenticate_ip_ttl
TYPE: time_t
LOC: Config.authenticateIpTTL
DEFAULT: 0 seconds
DOC_START
	If you use proxy authentication and the 'max_user_ip' ACL,
	this directive controls how long Squid remembers the IP
	addresses associated with each user.  Use a small value
	(e.g., 60 seconds) if your users might change addresses
	quickly, as is the case with dialups.   You might be safe
	using a larger value (e.g., 2 hours) in a corporate LAN
	environment with relatively static address assignments.
DOC_END

COMMENT_START
 ACCESS CONTROLS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: external_acl_type
TYPE: externalAclHelper
LOC: Config.externalAclHelperList
DEFAULT: none
DOC_START
	This option defines external acl classes using a helper program
	to look up the status

	  external_acl_type name [options] FORMAT.. /path/to/helper [helper arguments..]

	Options:

	  ttl=n		TTL in seconds for cached results (defaults to 3600
	  		for 1 hour)
	  negative_ttl=n
	  		TTL for cached negative lookups (default same
	  		as ttl)
	  children=n	Number of acl helper processes spawn to service
			external acl lookups of this type. (default 5)
	  concurrency=n	concurrency level per process. Only used with helpers
			capable of processing more than one query at a time.
	  cache=n	result cache size, 0 is unbounded (default)
	  grace=n	Percentage remaining of TTL where a refresh of a
			cached entry should be initiated without needing to
			wait for a new reply. (default 0 for no grace period)
	  protocol=2.5	Compatibility mode for Squid-2.5 external acl helpers
	  ipv4 / ipv6	IP-mode used to communicate to this helper.
			For compatability with older configurations and helpers
			'ipv4' is the default unless --with-localhost-ipv6 is used.
			--with-localhost-ipv6 changes the default to 'ipv6'.
			SPECIAL NOTE: these options override --with-localhost-ipv6

	FORMAT specifications

	  %LOGIN	Authenticated user login name
	  %EXT_USER	Username from external acl
	  %IDENT	Ident user name
	  %SRC		Client IP
	  %SRCPORT	Client source port
	  %URI		Requested URI
	  %DST		Requested host
	  %PROTO	Requested protocol
	  %PORT		Requested port
	  %PATH		Requested URL path
	  %METHOD	Request method
	  %MYADDR	Squid interface address
	  %MYPORT	Squid http_port number
	  %PATH		Requested URL-path (including query-string if any)
	  %USER_CERT	SSL User certificate in PEM format
	  %USER_CERTCHAIN SSL User certificate chain in PEM format
	  %USER_CERT_xx	SSL User certificate subject attribute xx
	  %USER_CA_xx	SSL User certificate issuer attribute xx

	  %>{Header}	HTTP request header
	  %>{Hdr:member}
	  		HTTP request header list member
	  %>{Hdr:;member}
	  		HTTP request header list member using ; as
	  		list separator. ; can be any non-alphanumeric
			character.

	  %<{Header}	HTTP reply header
	  %<{Hdr:member}
	  		HTTP reply header list member
	  %<{Hdr:;member}
	  		HTTP reply header list member using ; as
	  		list separator. ; can be any non-alphanumeric
			character.

	In addition to the above, any string specified in the referencing
	acl will also be included in the helper request line, after the
	specified formats (see the "acl external" directive)

	The helper receives lines per the above format specification,
	and returns lines starting with OK or ERR indicating the validity
	of the request and optionally followed by additional keywords with
	more details.

	General result syntax:

	  OK/ERR keyword=value ...

	Defined keywords:

	  user=		The users name (login)
	  password=	The users password (for login= cache_peer option)
	  message=	Message describing the reason. Available as %o
	  		in error pages
	  tag=		Apply a tag to a request (for both ERR and OK results)
	  		Only sets a tag, does not alter existing tags.
	  log=		String to be logged in access.log. Available as
	  		%ea in logformat specifications

	If protocol=3.0 (the default) then URL escaping is used to protect
	each value in both requests and responses.

	If using protocol=2.5 then all values need to be enclosed in quotes
	if they may contain whitespace, or the whitespace escaped using \.
	And quotes or \ characters within the keyword value must be \ escaped.

	When using the concurrency= option the protocol is changed by
	introducing a query channel tag infront of the request/response.
	The query channel tag is a number between 0 and concurrency-1.
DOC_END

NAME: acl
TYPE: acl
LOC: Config.aclList
DEFAULT: all src all
DOC_START
	Defining an Access List

	Every access list definition must begin with an aclname and acltype, 
	followed by either type-specific arguments or a quoted filename that
	they are read from.

	   acl aclname acltype argument ...
	   acl aclname acltype "file" ...

	When using "file", the file should contain one item per line.

	By default, regular expressions are CASE-SENSITIVE.  To make
	them case-insensitive, use the -i option.


	***** ACL TYPES AVAILABLE *****

	acl aclname src ip-address/netmask ...		# clients IP address
	acl aclname src addr1-addr2/netmask ...		# range of addresses
	acl aclname dst ip-address/netmask ...		# URL host's IP address
	acl aclname myip ip-address/netmask ...		# local socket IP address

	acl aclname arp      mac-address ... (xx:xx:xx:xx:xx:xx notation)
	  # The arp ACL requires the special configure option --enable-arp-acl.
	  # Furthermore, the ARP ACL code is not portable to all operating systems.
	  # It works on Linux, Solaris, Windows, FreeBSD, and some other *BSD variants.
	  #
	  # NOTE: Squid can only determine the MAC address for clients that are on
	  # the same subnet. If the client is on a different subnet, then Squid cannot
	  # find out its MAC address.

	acl aclname srcdomain   .foo.com ...    	# reverse lookup, from client IP
	acl aclname dstdomain   .foo.com ...    	# Destination server from URL
	acl aclname srcdom_regex [-i] \.foo\.com ...	# regex matching client name
	acl aclname dstdom_regex [-i] \.foo\.com ...	# regex matching server
	  # For dstdomain and dstdom_regex a reverse lookup is tried if a IP
	  # based URL is used and no match is found. The name "none" is used
	  # if the reverse lookup fails.

	acl aclname src_as number ...
	acl aclname dst_as number ...
	  # Except for access control, AS numbers can be used for
	  # routing of requests to specific caches. Here's an
	  # example for routing all requests for AS#1241 and only
	  # those to mycache.mydomain.net:
	  # acl asexample dst_as 1241
	  # cache_peer_access mycache.mydomain.net allow asexample
	  # cache_peer_access mycache_mydomain.net deny all

	acl aclname peername myPeer ...
	  # match against a named cache_peer entry
	  # set unique name= on cache_peer lines for reliable use.

	acl aclname time [day-abbrevs] [h1:m1-h2:m2]
	  #  day-abbrevs:
	  #	S - Sunday
	  #	M - Monday
	  #	T - Tuesday
	  #	W - Wednesday
	  #	H - Thursday
	  #	F - Friday
	  #	A - Saturday
	  #  h1:m1 must be less than h2:m2

	acl aclname url_regex [-i] ^http:// ...		# regex matching on whole URL
	acl aclname urlpath_regex [-i] \.gif$ ...	# regex matching on URL path

	acl aclname port 80 70 21 ...
	acl aclname port 0-1024 ...		# ranges allowed
	acl aclname myport 3128 ...		# (local socket TCP port)
	acl aclname myportname 3128 ...		# http(s)_port name

	acl aclname proto HTTP FTP ...

	acl aclname method GET POST ...

	acl aclname http_status 200 301 500- 400-403 ...     # status code in reply

	acl aclname browser [-i] regexp ...
	  # pattern match on User-Agent header (see also req_header below)

	acl aclname referer_regex [-i] regexp ...
	  # pattern match on Referer header
	  # Referer is highly unreliable, so use with care

	acl aclname ident username ...
	acl aclname ident_regex [-i] pattern ...
	  # string match on ident output.
	  # use REQUIRED to accept any non-null ident.

	acl aclname proxy_auth [-i] username ...
	acl aclname proxy_auth_regex [-i] pattern ...
	  # list of valid usernames
	  # use REQUIRED to accept any valid username.
	  #
	  # NOTE: when a Proxy-Authentication header is sent but it is not
	  # needed during ACL checking the username is NOT logged
	  # in access.log.
	  #
	  # NOTE: proxy_auth requires a EXTERNAL authentication program
	  # to check username/password combinations (see
	  # auth_param directive).
	  #
	  # NOTE: proxy_auth can't be used in a transparent/intercepting proxy
	  # as the browser needs to be configured for using a proxy in order
	  # to respond to proxy authentication.

	acl aclname snmp_community string ...
	  # A community string to limit access to your SNMP Agent
	  # Example:
	  #
	  #	acl snmppublic snmp_community public

	acl aclname maxconn number
	  # This will be matched when the client's IP address has
	  # more than <number> HTTP connections established.

	acl aclname max_user_ip [-s] number
	  # This will be matched when the user attempts to log in from more
	  # than <number> different ip addresses. The authenticate_ip_ttl
	  # parameter controls the timeout on the ip entries.
	  # If -s is specified the limit is strict, denying browsing
	  # from any further IP addresses until the ttl has expired. Without
	  # -s Squid will just annoy the user by "randomly" denying requests.
	  # (the counter is reset each time the limit is reached and a
	  # request is denied)
	  # NOTE: in acceleration mode or where there is mesh of child proxies,
	  # clients may appear to come from multiple addresses if they are
	  # going through proxy farms, so a limit of 1 may cause user problems.

	acl aclname req_mime_type [-i] mime-type ...
	  # regex match against the mime type of the request generated
	  # by the client. Can be used to detect file upload or some
	  # types HTTP tunneling requests.
	  # NOTE: This does NOT match the reply. You cannot use this
	  # to match the returned file type.

	acl aclname req_header header-name [-i] any\.regex\.here
	  # regex match against any of the known request headers.  May be
	  # thought of as a superset of "browser", "referer" and "mime-type"
	  # ACLs.

	acl aclname rep_mime_type [-i] mime-type ...
	  # regex match against the mime type of the reply received by
	  # squid. Can be used to detect file download or some
	  # types HTTP tunneling requests.
	  # NOTE: This has no effect in http_access rules. It only has
	  # effect in rules that affect the reply data stream such as
	  # http_reply_access.

	acl aclname rep_header header-name [-i] any\.regex\.here
	  # regex match against any of the known reply headers. May be
	  # thought of as a superset of "browser", "referer" and "mime-type"
	  # ACLs.

	acl aclname external class_name [arguments...]
	  # external ACL lookup via a helper class defined by the
	  # external_acl_type directive.

	acl aclname user_cert attribute values...
	  # match against attributes in a user SSL certificate
	  # attribute is one of DN/C/O/CN/L/ST

	acl aclname ca_cert attribute values...
	  # match against attributes a users issuing CA SSL certificate
	  # attribute is one of DN/C/O/CN/L/ST

	acl aclname ext_user username ...
	acl aclname ext_user_regex [-i] pattern ...
	  # string match on username returned by external acl helper
	  # use REQUIRED to accept any non-null user name.

Examples:
acl macaddress arp 09:00:2b:23:45:67
acl myexample dst_as 1241
acl password proxy_auth REQUIRED
acl fileupload req_mime_type -i ^multipart/form-data$
acl javascript rep_mime_type -i ^application/x-javascript$

NOCOMMENT_START
#Recommended minimum configuration:
acl manager proto cache_object
acl localhost src 127.0.0.1/32
acl to_localhost dst 127.0.0.0/8
#
# Example rule allowing access from your local networks.
# Adapt to list your (internal) IP networks from where browsing
# should be allowed
acl localnet src 10.0.0.0/8	# RFC1918 possible internal network
acl localnet src 172.16.0.0/12	# RFC1918 possible internal network
acl localnet src 192.168.0.0/16	# RFC1918 possible internal network
#
acl SSL_ports port 443
acl Safe_ports port 80		# http
acl Safe_ports port 21		# ftp
acl Safe_ports port 443		# https
acl Safe_ports port 70		# gopher
acl Safe_ports port 210		# wais
acl Safe_ports port 1025-65535	# unregistered ports
acl Safe_ports port 280		# http-mgmt
acl Safe_ports port 488		# gss-http
acl Safe_ports port 591		# filemaker
acl Safe_ports port 777		# multiling http
acl CONNECT method CONNECT
NOCOMMENT_END
DOC_END

NAME: follow_x_forwarded_for
TYPE: acl_access
IFDEF: FOLLOW_X_FORWARDED_FOR
LOC: Config.accessList.followXFF
DEFAULT: none
DEFAULT_IF_NONE: deny all
DOC_START
	Allowing or Denying the X-Forwarded-For header to be followed to
	find the original source of a request.

	Requests may pass through a chain of several other proxies
	before reaching us.  The X-Forwarded-For header will contain a
	comma-separated list of the IP addresses in the chain, with the
	rightmost address being the most recent.

	If a request reaches us from a source that is allowed by this
	configuration item, then we consult the X-Forwarded-For header
	to see where that host received the request from.  If the
	X-Forwarded-For header contains multiple addresses, and if
	acl_uses_indirect_client is on, then we continue backtracking
	until we reach an address for which we are not allowed to
	follow the X-Forwarded-For header, or until we reach the first
	address in the list.  (If acl_uses_indirect_client is off, then
	it's impossible to backtrack through more than one level of
	X-Forwarded-For addresses.)

	The end result of this process is an IP address that we will
	refer to as the indirect client address.  This address may
	be treated as the client address for access control, delay
	pools and logging, depending on the acl_uses_indirect_client,
	delay_pool_uses_indirect_client and log_uses_indirect_client
	options.

	SECURITY CONSIDERATIONS:

		Any host for which we follow the X-Forwarded-For header
		can place incorrect information in the header, and Squid
		will use the incorrect information as if it were the
		source address of the request.  This may enable remote
		hosts to bypass any access control restrictions that are
		based on the client's source addresses.

	For example:

		acl localhost src 127.0.0.1
		acl my_other_proxy srcdomain .proxy.example.com
		follow_x_forwarded_for allow localhost
		follow_x_forwarded_for allow my_other_proxy
DOC_END

NAME: acl_uses_indirect_client
COMMENT: on|off
TYPE: onoff
IFDEF: FOLLOW_X_FORWARDED_FOR
DEFAULT: on
LOC: Config.onoff.acl_uses_indirect_client
DOC_START
	Controls whether the indirect client address
	(see follow_x_forwarded_for) is used instead of the
	direct client address in acl matching.
DOC_END

NAME: delay_pool_uses_indirect_client
COMMENT: on|off
TYPE: onoff
IFDEF: FOLLOW_X_FORWARDED_FOR DELAY_POOLS
DEFAULT: on
LOC: Config.onoff.delay_pool_uses_indirect_client
DOC_START
	Controls whether the indirect client address
	(see follow_x_forwarded_for) is used instead of the
	direct client address in delay pools.
DOC_END

NAME: log_uses_indirect_client
COMMENT: on|off
TYPE: onoff
IFDEF: FOLLOW_X_FORWARDED_FOR
DEFAULT: on
LOC: Config.onoff.log_uses_indirect_client
DOC_START
	Controls whether the indirect client address
	(see follow_x_forwarded_for) is used instead of the
	direct client address in the access log.
DOC_END

NAME: http_access
TYPE: acl_access
LOC: Config.accessList.http
DEFAULT: none
DEFAULT_IF_NONE: deny all
DOC_START
	Allowing or Denying access based on defined access lists

	Access to the HTTP port:
	http_access allow|deny [!]aclname ...

	NOTE on default values:

	If there are no "access" lines present, the default is to deny
	the request.

	If none of the "access" lines cause a match, the default is the
	opposite of the last line in the list.  If the last line was
	deny, the default is allow.  Conversely, if the last line
	is allow, the default will be deny.  For these reasons, it is a
	good idea to have an "deny all" or "allow all" entry at the end
	of your access lists to avoid potential confusion.

NOCOMMENT_START
#Recommended minimum configuration:
#
# Only allow cachemgr access from localhost
http_access allow manager localhost
http_access deny manager
# Deny requests to unknown ports
http_access deny !Safe_ports
# Deny CONNECT to other than SSL ports
http_access deny CONNECT !SSL_ports
#
# We strongly recommend the following be uncommented to protect innocent
# web applications running on the proxy server who think the only
# one who can access services on "localhost" is a local user
#http_access deny to_localhost
#
# INSERT YOUR OWN RULE(S) HERE TO ALLOW ACCESS FROM YOUR CLIENTS

# Example rule allowing access from your local networks.
# Adapt localnet in the ACL section to list your (internal) IP networks
# from where browsing should be allowed
http_access allow localnet

# And finally deny all other access to this proxy
http_access deny all
NOCOMMENT_END
DOC_END

NAME: http_reply_access
TYPE: acl_access
LOC: Config.accessList.reply
DEFAULT: none
DOC_START
	Allow replies to client requests. This is complementary to http_access.

	http_reply_access allow|deny [!] aclname ...

	NOTE: if there are no access lines present, the default is to allow
	all replies

	If none of the access lines cause a match the opposite of the
	last line will apply. Thus it is good practice to end the rules
	with an "allow all" or "deny all" entry.
DOC_END

NAME: icp_access
TYPE: acl_access
LOC: Config.accessList.icp
DEFAULT: none
DEFAULT_IF_NONE: deny all
DOC_START
	Allowing or Denying access to the ICP port based on defined
	access lists

	icp_access  allow|deny [!]aclname ...

	See http_access for details

NOCOMMENT_START
#Allow ICP queries from local networks only
#icp_access allow localnet
#icp_access deny all
NOCOMMENT_END
DOC_END

NAME: htcp_access
IFDEF: USE_HTCP
TYPE: acl_access
LOC: Config.accessList.htcp
DEFAULT: none
DEFAULT_IF_NONE: deny all
DOC_START
	Allowing or Denying access to the HTCP port based on defined
	access lists

	htcp_access  allow|deny [!]aclname ...

	See http_access for details

	NOTE: The default if no htcp_access lines are present is to
	deny all traffic. This default may cause problems with peers
	using the htcp or htcp-oldsquid options.

NOCOMMENT_START
#Allow HTCP queries from local networks only
#htcp_access allow localnet
#htcp_access deny all
NOCOMMENT_END
DOC_END

NAME: htcp_clr_access
IFDEF: USE_HTCP
TYPE: acl_access
LOC: Config.accessList.htcp_clr
DEFAULT: none
DEFAULT_IF_NONE: deny all
DOC_START
	Allowing or Denying access to purge content using HTCP based
	on defined access lists

	htcp_clr_access  allow|deny [!]aclname ...

	See http_access for details

#Allow HTCP CLR requests from trusted peers
acl htcp_clr_peer src 172.16.1.2
htcp_clr_access allow htcp_clr_peer
DOC_END

NAME: miss_access
TYPE: acl_access
LOC: Config.accessList.miss
DEFAULT: allow all
DOC_START
	Use to force your neighbors to use you as a sibling instead of
	a parent.  For example:

		acl localclients src 172.16.0.0/16
		miss_access allow localclients
		miss_access deny  !localclients

	This means only your local clients are allowed to fetch
	MISSES and all other clients can only fetch HITS.

	By default, allow all clients who passed the http_access rules
	to fetch MISSES from us.
DOC_END

NAME: ident_lookup_access
TYPE: acl_access
IFDEF: USE_IDENT
DEFAULT: none
DEFAULT_IF_NONE: deny all
LOC: Config.accessList.identLookup
DOC_START
	A list of ACL elements which, if matched, cause an ident
	(RFC 931) lookup to be performed for this request.  For
	example, you might choose to always perform ident lookups
	for your main multi-user Unix boxes, but not for your Macs
	and PCs.  By default, ident lookups are not performed for
	any requests.

	To enable ident lookups for specific client addresses, you
	can follow this example:

	acl ident_aware_hosts src 198.168.1.0/255.255.255.0
	ident_lookup_access allow ident_aware_hosts
	ident_lookup_access deny all

	Only src type ACL checks are fully supported.  A src_domain
	ACL might work at times, but it will not always provide
	the correct result.
DOC_END

NAME: reply_body_max_size
COMMENT: size [acl acl...]
TYPE: acl_b_size_t
DEFAULT: none
LOC: Config.ReplyBodySize
DOC_START
	This option specifies the maximum size of a reply body. It can be
	used to prevent users from downloading very large files, such as
	MP3's and movies. When the reply headers are received, the
	reply_body_max_size lines are processed, and the first line where
	all (if any) listed ACLs are true is used as the maximum body size
	for this reply.

	This size is checked twice. First when we get the reply headers,
	we check the content-length value.  If the content length value exists
	and is larger than the allowed size, the request is denied and the
	user receives an error message that says "the request or reply
	is too large." If there is no content-length, and the reply
	size exceeds this limit, the client's connection is just closed
	and they will receive a partial reply.

	WARNING: downstream caches probably can not detect a partial reply
	if there is no content-length header, so they will cache
	partial responses and give them out as hits.  You should NOT
	use this option if you have downstream caches.

	WARNING: A maximum size smaller than the size of squid's error messages
	will cause an infinite loop and crash squid. Ensure that the smallest
	non-zero value you use is greater that the maximum header size plus
	the size of your largest error page.

	If you set this parameter none (the default), there will be
	no limit imposed.

	Configuration Format is:
		reply_body_max_size SIZE UNITS [acl ...]
	ie.
		reply_body_max_size 10 MB

DOC_END

COMMENT_START
 NETWORK OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: http_port ascii_port
TYPE: http_port_list
DEFAULT: none
LOC: Config.Sockaddr.http
DOC_START
	Usage:	port [options]
		hostname:port [options]
		1.2.3.4:port [options]

	The socket addresses where Squid will listen for HTTP client
	requests.  You may specify multiple socket addresses.
	There are three forms: port alone, hostname with port, and
	IP address with port.  If you specify a hostname or IP
	address, Squid binds the socket to that specific
	address.  This replaces the old 'tcp_incoming_address'
	option.  Most likely, you do not need to bind to a specific
	address, so you can use the port number alone.

	If you are running Squid in accelerator mode, you
	probably want to listen on port 80 also, or instead.

	The -a command line option may be used to specify additional
	port(s) where Squid listens for proxy request. Such ports will
	be plain proxy ports with no options.

	You may specify multiple socket addresses on multiple lines.

	Options:

	   intercept	Support for IP-Layer interception of
			outgoing requests without browser settings.
			NP: disables authentication and IPv6 on the port.

	   tproxy	Support Linux TPROXY for spoofing outgoing
			connections using the client IP address.
			NP: disables authentication and IPv6 on the port.

	   accel	Accelerator mode. Also needs at least one of
			vhost / vport / defaultsite.

	   defaultsite=domainname
			What to use for the Host: header if it is not present
			in a request. Determines what site (not origin server)
			accelerators should consider the default.
			Implies accel.

	   vhost	Accelerator mode using Host header for virtual
			domain support. Implies accel.

	   vport	Accelerator with IP based virtual host support.
			Implies accel.

	   vport=NN	As above, but uses specified port number rather
			than the http_port number. Implies accel.

	   protocol=	Protocol to reconstruct accelerated requests with.
			Defaults to http.

           connection-auth[=on|off]
                        use connection-auth=off to tell Squid to prevent 
                        forwarding Microsoft connection oriented authentication
			(NTLM, Negotiate and Kerberos)

	   disable-pmtu-discovery=
			Control Path-MTU discovery usage:
			    off		lets OS decide on what to do (default).
			    transparent	disable PMTU discovery when transparent
					support is enabled.
			    always	disable always PMTU discovery.

			In many setups of transparently intercepting proxies
			Path-MTU discovery can not work on traffic towards the
			clients. This is the case when the intercepting device
			does not fully track connections and fails to forward
			ICMP must fragment messages to the cache server. If you
			have such setup and experience that certain clients
			sporadically hang or never complete requests set
			disable-pmtu-discovery option to 'transparent'.

           sslBump 	Intercept each CONNECT request matching ssl_bump ACL,
			establish secure connection with the client and with
			the server, decrypt HTTP messages as they pass through
			Squid, and treat them as unencrypted HTTP messages,
			becoming the man-in-the-middle.

			When this option is enabled, additional options become
			available to specify SSL-related properties of the
			client-side connection: cert, key, version, cipher,
			options, clientca, cafile, capath, crlfile, dhparams,
			sslflags, and sslcontext. See the https_port directive
			for more information on these options.

			The ssl_bump option is required to fully enable
			the SslBump feature.

	   name=	Specifies a internal name for the port. Defaults to
			the port specification (port or addr:port)

	   keepalive[=idle,interval,timeout]
			Enable TCP keepalive probes of idle connections
			idle is the initial time before TCP starts probing
			the connection, interval how often to probe, and
			timeout the time before giving up.

	If you run Squid on a dual-homed machine with an internal
	and an external interface we recommend you to specify the
	internal address:port in http_port. This way Squid will only be
	visible on the internal address.

NOCOMMENT_START
# Squid normally listens to port 3128
http_port @DEFAULT_HTTP_PORT@
NOCOMMENT_END
DOC_END

NAME: https_port
IFDEF: USE_SSL
TYPE: https_port_list
DEFAULT: none
LOC: Config.Sockaddr.https
DOC_START
	Usage:  [ip:]port cert=certificate.pem [key=key.pem] [options...]

	The socket address where Squid will listen for HTTPS client
	requests.

	This is really only useful for situations where you are running
	squid in accelerator mode and you want to do the SSL work at the
	accelerator level.

	You may specify multiple socket addresses on multiple lines,
	each with their own SSL certificate and/or options.

	Options:

	   accel	Accelerator mode. Also needs at least one of
			defaultsite or vhost.

	   defaultsite=	The name of the https site presented on
	   		this port. Implies accel.

	   vhost	Accelerator mode using Host header for virtual
			domain support. Requires a wildcard certificate
			or other certificate valid for more than one domain.
			Implies accel.

	   protocol=	Protocol to reconstruct accelerated requests with.
			Defaults to https.

	   cert=	Path to SSL certificate (PEM format).

	   key=		Path to SSL private key file (PEM format)
			if not specified, the certificate file is
			assumed to be a combined certificate and
			key file.

	   version=	The version of SSL/TLS supported
			    1	automatic (default)
			    2	SSLv2 only
			    3	SSLv3 only
			    4	TLSv1 only

	   cipher=	Colon separated list of supported ciphers.

	   options=	Various SSL engine options. The most important
			being:
			    NO_SSLv2  Disallow the use of SSLv2
			    NO_SSLv3  Disallow the use of SSLv3
			    NO_TLSv1  Disallow the use of TLSv1
			    SINGLE_DH_USE Always create a new key when using
				      temporary/ephemeral DH key exchanges
			See src/ssl_support.c or OpenSSL SSL_CTX_set_options
			documentation for a complete list of options.

	   clientca=	File containing the list of CAs to use when
			requesting a client certificate.

	   cafile=	File containing additional CA certificates to
			use when verifying client certificates. If unset
			clientca will be used.

	   capath=	Directory containing additional CA certificates
			and CRL lists to use when verifying client certificates.

	   crlfile=	File of additional CRL lists to use when verifying
			the client certificate, in addition to CRLs stored in
			the capath. Implies VERIFY_CRL flag below.

	   dhparams=	File containing DH parameters for temporary/ephemeral
			DH key exchanges.

	   sslflags=	Various flags modifying the use of SSL:
			    DELAYED_AUTH
				Don't request client certificates
				immediately, but wait until acl processing
				requires a certificate (not yet implemented).
			    NO_DEFAULT_CA
				Don't use the default CA lists built in
				to OpenSSL.
			    NO_SESSION_REUSE
				Don't allow for session reuse. Each connection
				will result in a new SSL session.
			    VERIFY_CRL
				Verify CRL lists when accepting client
				certificates.
			    VERIFY_CRL_ALL
				Verify CRL lists for all certificates in the
				client certificate chain.

	   sslcontext=	SSL session ID context identifier.

	   vport	Accelerator with IP based virtual host support.

	   vport=NN	As above, but uses specified port number rather
			than the https_port number. Implies accel.

	   name=	Specifies a internal name for the port. Defaults to
			the port specification (port or addr:port)

DOC_END

NAME: tcp_outgoing_tos tcp_outgoing_ds tcp_outgoing_dscp
TYPE: acl_tos
DEFAULT: none
LOC: Config.accessList.outgoing_tos
DOC_START
	Allows you to select a TOS/Diffserv value to mark outgoing
	connections with, based on the username or source address
	making the request.

	tcp_outgoing_tos ds-field [!]aclname ...

	Example where normal_service_net uses the TOS value 0x00
	and normal_service_net uses 0x20

	acl normal_service_net src 10.0.0.0/255.255.255.0
	acl good_service_net src 10.0.1.0/255.255.255.0
	tcp_outgoing_tos 0x00 normal_service_net
	tcp_outgoing_tos 0x20 good_service_net

	TOS/DSCP values really only have local significance - so you should
	know what you're specifying. For more information, see RFC2474 and
	RFC3260.

	The TOS/DSCP byte must be exactly that - a octet value  0 - 255, or
	"default" to use whatever default your host has. Note that in
	practice often only values 0 - 63 is usable as the two highest bits
	have been redefined for use by ECN (RFC3168).

	Processing proceeds in the order specified, and stops at first fully
	matching line.

	Note: The use of this directive using client dependent ACLs is
	incompatible with the use of server side persistent connections. To
	ensure correct results it is best to set server_persisten_connections
	to off when using this directive in such configurations.
DOC_END

NAME: clientside_tos
TYPE: acl_tos
DEFAULT: none
LOC: Config.accessList.clientside_tos
DOC_START
	Allows you to select a TOS/Diffserv value to mark client-side
	connections with, based on the username or source address
	making the request.
DOC_END

NAME: zph_tos_local
TYPE: int
IFDEF: USE_ZPH_QOS
DEFAULT: 0
LOC: Config.zph_tos_local
DOC_START
       Allows you to select a TOS/Diffserv value to mark local hits. Read above
       (tcp_outgoing_tos) for details/requirements about TOS.
       Default: 0 (disabled).
DOC_END

NAME: zph_tos_peer
TYPE: int
IFDEF: USE_ZPH_QOS
DEFAULT: 0
LOC: Config.zph_tos_peer
DOC_START
       Allows you to select a TOS/Diffserv value to mark peer hits. Read above
       (tcp_outgoing_tos) for details/requirements about TOS.
       Default: 0 (disabled).
DOC_END

NAME: zph_tos_parent
COMMENT: on|off
TYPE: onoff
IFDEF: USE_ZPH_QOS
DEFAULT: on
LOC: Config.onoff.zph_tos_parent
DOC_START
       Set this to off if you want only sibling hits to be marked.
       If set to on (default), parent hits are being marked too.
DOC_END

NAME: zph_preserve_miss_tos
COMMENT: on|off
TYPE: onoff
IFDEF: USE_ZPH_QOS
DEFAULT: on
LOC: Config.onoff.zph_preserve_miss_tos
DOC_START
       If set to on (default), any HTTP response towards clients will
       have the TOS value of the response comming from the remote
       server masked with the value of zph_preserve_miss_tos_mask.
       For this to work correctly, you will need to patch your linux
       kernel with the TOS preserving ZPH patch.
       The kernel patch can be downloaded from http://zph.bratcheda.org
DOC_END

NAME: zph_preserve_miss_tos_mask
TYPE: int
IFDEF: USE_ZPH_QOS
DEFAULT: 255
LOC: Config.zph_preserve_miss_tos_mask
DOC_START
       Allows you to mask certain bits in the TOS received from the
       remote server, before copying the value to the TOS send towards
       clients.
       Default: 255 (TOS from server is not changed).
DOC_END

NAME: tcp_outgoing_address
TYPE: acl_address
DEFAULT: none
LOC: Config.accessList.outgoing_address
DOC_START
	Allows you to map requests to different outgoing IP addresses
	based on the username or source address of the user making
	the request.

	tcp_outgoing_address ipaddr [[!]aclname] ...

	Example where requests from 10.0.0.0/24 will be forwarded
	with source address 10.1.0.1, 10.0.2.0/24 forwarded with
	source address 10.1.0.2 and the rest will be forwarded with
	source address 10.1.0.3.

	acl normal_service_net src 10.0.0.0/24
	acl good_service_net src 10.0.2.0/24
	tcp_outgoing_address 10.1.0.1 normal_service_net
	tcp_outgoing_address 10.1.0.2 good_service_net
	tcp_outgoing_address 10.1.0.3

	Processing proceeds in the order specified, and stops at first fully
	matching line.

	Note: The use of this directive using client dependent ACLs is
	incompatible with the use of server side persistent connections. To
	ensure correct results it is best to set server_persistent_connections
	to off when using this directive in such configurations.


        IPv6 Magic:

	Squid is built with a capability of bridging the IPv4 and IPv6 internets.
	tcp_outgoing_address as exampled above breaks this bridging by forcing
	all outbound traffic through a certain IPv4 which may be on the wrong
	side of the IPv4/IPv6 boundary.

	To operate with tcp_outgoing_address and keep the bridging benefits
	an additional ACL needs to be used which ensures the IPv6-bound traffic
	is never forced or permitted out the IPv4 interface.

	acl to_ipv6 dst ipv6
	tcp_outgoing_address 2002::c001 good_service_net to_ipv6
	tcp_outgoing_address 10.1.0.2 good_service_net !to_ipv6

	tcp_outgoing_address 2002::beef normal_service_net to_ipv6
	tcp_outgoing_address 10.1.0.1 normal_service_net !to_ipv6

	tcp_outgoing_address 2002::1 to_ipv6
	tcp_outgoing_address 10.1.0.3 !to_ipv6

	WARNING:
	  'dst ipv6' bases its selection assuming DIRECT access.
	  If peers are used the peername ACL are needed to select outgoing
	  address which can link to the peer.

DOC_END

COMMENT_START
 SSL OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: ssl_unclean_shutdown
IFDEF: USE_SSL
TYPE: onoff
DEFAULT: off
LOC: Config.SSL.unclean_shutdown
DOC_START
	Some browsers (especially MSIE) bugs out on SSL shutdown
	messages.
DOC_END

NAME: ssl_engine
IFDEF: USE_SSL
TYPE: string
LOC: Config.SSL.ssl_engine
DEFAULT: none
DOC_START
	The OpenSSL engine to use. You will need to set this if you
	would like to use hardware SSL acceleration for example.
DOC_END

NAME: sslproxy_client_certificate
IFDEF: USE_SSL
DEFAULT: none
LOC: Config.ssl_client.cert
TYPE: string
DOC_START
	Client SSL Certificate to use when proxying https:// URLs
DOC_END

NAME: sslproxy_client_key
IFDEF: USE_SSL
DEFAULT: none
LOC: Config.ssl_client.key
TYPE: string
DOC_START
	Client SSL Key to use when proxying https:// URLs
DOC_END

NAME: sslproxy_version
IFDEF: USE_SSL
DEFAULT: 1
LOC: Config.ssl_client.version
TYPE: int
DOC_START
	SSL version level to use when proxying https:// URLs
DOC_END

NAME: sslproxy_options
IFDEF: USE_SSL
DEFAULT: none
LOC: Config.ssl_client.options
TYPE: string
DOC_START
	SSL engine options to use when proxying https:// URLs
DOC_END

NAME: sslproxy_cipher
IFDEF: USE_SSL
DEFAULT: none
LOC: Config.ssl_client.cipher
TYPE: string
DOC_START
	SSL cipher list to use when proxying https:// URLs
DOC_END

NAME: sslproxy_cafile
IFDEF: USE_SSL
DEFAULT: none
LOC: Config.ssl_client.cafile
TYPE: string
DOC_START
	file containing CA certificates to use when verifying server
	certificates while proxying https:// URLs
DOC_END

NAME: sslproxy_capath
IFDEF: USE_SSL
DEFAULT: none
LOC: Config.ssl_client.capath
TYPE: string
DOC_START
	directory containing CA certificates to use when verifying
	server certificates while proxying https:// URLs
DOC_END

NAME: ssl_bump
IFDEF: USE_SSL
TYPE: acl_access
LOC: Config.accessList.ssl_bump
DEFAULT: none
DOC_START
	This ACL controls which CONNECT requests to an http_port
	marked with an sslBump flag are actually "bumped". Please 
	see the sslBump flag of an http_port option for more details
	about decoding proxied SSL connections.

	By default, no requests are bumped.

	See also: http_port sslBump
   
NOCOMMENT_START
# Example: Bump all requests except those originating from localhost and 
# those going to webax.com or example.com sites.
#
# acl localhost src 127.0.0.1/32
# acl broken_sites dstdomain .webax.com
# acl broken_sites dstdomain .example.com
# ssl_bump deny localhost
# ssl_bump deny broken_sites
# ssl_bump allow all
NOCOMMENT_END
DOC_END

NAME: sslproxy_flags
IFDEF: USE_SSL
DEFAULT: none
LOC: Config.ssl_client.flags
TYPE: string
DOC_START
	Various flags modifying the use of SSL while proxying https:// URLs:
	    DONT_VERIFY_PEER	Accept certificates that fail verification.
				For refined control, see sslproxy_cert_error.
	    NO_DEFAULT_CA	Don't use the default CA list built in
				to OpenSSL.
DOC_END


NAME: sslproxy_cert_error
IFDEF: USE_SSL
DEFAULT: none
LOC: Config.ssl_client.cert_error
TYPE: acl_access
DOC_START
	Use this ACL to bypass server certificate validation errors.

	For example, the following lines will bypass all validation errors
	when talking to servers located at 172.16.0.0/16. All other
	validation errors will result in ERR_SECURE_CONNECT_FAIL error.

		acl BrokenServersAtTrustedIP dst 172.16.0.0/16
		sslproxy_cert_error allow BrokenServersAtTrustedIP
		sslproxy_cert_error deny all

	This option must use fast ACL expressions only. Expressions that use
	external lookups or communication result in unpredictable behavior or
	crashes.

	Without this option, all server certificate validation errors
	terminate the transaction. Bypassing validation errors is dangerous
	because an error usually implies that the server cannot be trusted and
	the connection may be insecure.

	See also: sslproxy_flags and DONT_VERIFY_PEER.

NOCOMMENT_START
#Default setting:
# sslproxy_cert_error deny all
NOCOMMENT_END
DOC_END



NAME: sslpassword_program
IFDEF: USE_SSL
DEFAULT: none
LOC: Config.Program.ssl_password
TYPE: string
DOC_START
	Specify a program used for entering SSL key passphrases
	when using encrypted SSL certificate keys. If not specified
	keys must either be unencrypted, or Squid started with the -N
	option to allow it to query interactively for the passphrase.
DOC_END

COMMENT_START
 OPTIONS WHICH AFFECT THE NEIGHBOR SELECTION ALGORITHM
 -----------------------------------------------------------------------------
COMMENT_END

NAME: cache_peer
TYPE: peer
DEFAULT: none
LOC: Config.peers
DOC_START
	To specify other caches in a hierarchy, use the format:

		cache_peer hostname type http-port icp-port [options]

	For example,

	#                                        proxy  icp
	#          hostname             type     port   port  options
	#          -------------------- -------- ----- -----  -----------
	cache_peer parent.foo.net       parent    3128  3130  proxy-only default
	cache_peer sib1.foo.net         sibling   3128  3130  proxy-only
	cache_peer sib2.foo.net         sibling   3128  3130  proxy-only

	      type:  either 'parent', 'sibling', or 'multicast'.

	proxy-port:  The port number where the cache listens for proxy
		     requests.

	  icp-port:  Used for querying neighbor caches about
		     objects.  To have a non-ICP neighbor
		     specify '0' for the ICP port.
		NOTE: Also requires icp_port option enabled to send/receive
		      requests via this method.

	    options: proxy-only
		     weight=n
		     basetime=n
		     ttl=n
		     no-query
		     background-ping
		     default
		     round-robin
		     weighted-round-robin
		     carp
		     userhash
		     sourcehash
		     multicast-responder
		     closest-only
		     no-digest
		     no-netdb-exchange
		     no-delay
		     login=user:password | PASS | *:password
		     connect-timeout=nn
		     digest-url=url
		     allow-miss
		     max-conn=n
		     htcp
		     htcp-oldsquid
		     htcp-no-clr
		     htcp-no-purge-clr
		     htcp-only-clr
		     htcp-forward-clr
		     originserver
		     name=xxx
		     forceddomain=name
		     ssl
		     sslcert=/path/to/ssl/certificate
		     sslkey=/path/to/ssl/key
		     sslversion=1|2|3|4
		     sslcipher=...
		     ssloptions=...
		     front-end-https[=on|auto]
                     connection-auth[=on|off|auto]

		     use 'proxy-only' to specify objects fetched
		     from this cache should not be saved locally.

		     use 'weight=n' to affect the selection of a peer
		     during any weighted peer-selection mechanisms.
		     The weight must be an integer; default is 1,
		     larger weights are favored more.
		     This option does not affect parent selection if a peering
		     protocol is not in use.

		     use 'basetime=n' to specify a base amount to
		     be subtracted from round trip times of parents.
		     It is subtracted before division by weight in calculating
		     which parent to fectch from. If the rtt is less than the
		     base time the rtt is set to a minimal value.

		     use 'ttl=n' to specify a IP multicast TTL to use
		     when sending an ICP queries to this address.
		     Only useful when sending to a multicast group.
		     Because we don't accept ICP replies from random
		     hosts, you must configure other group members as
		     peers with the 'multicast-responder' option below.

		     use 'no-query' to NOT send ICP queries to this
		     neighbor.

		     use 'background-ping' to only send ICP queries to this
		     neighbor infrequently. This is used to keep the neighbor
		     round trip time updated and is usually used in
		     conjunction with weighted-round-robin.

		     use 'default' if this is a parent cache which can
		     be used as a "last-resort" if a peer cannot be located
		     by any of the peer-selection mechanisms.
		     If specified more than once, only the first is used.

		     use 'round-robin' to define a set of parents which
		     should be used in a round-robin fashion in the
		     absence of any ICP queries.

		     use 'weighted-round-robin' to define a set of parents
		     which should be used in a round-robin fashion with the
		     frequency of each parent being based on the round trip
		     time. Closer parents are used more often.
		     Usually used for background-ping parents.

		     use 'carp' to define a set of parents which should
		     be used as a CARP array. The requests will be
		     distributed among the parents based on the CARP load
		     balancing hash function based on their weight.

                     use 'userhash' to load-balance amongst a set of parents
                     based on the client proxy_auth or ident username.

                     use 'sourcehash' to load-balance amongst a set of parents
                     based on the client source ip.

		     'multicast-responder' indicates the named peer
		     is a member of a multicast group.  ICP queries will
		     not be sent directly to the peer, but ICP replies
		     will be accepted from it.

		     'closest-only' indicates that, for ICP_OP_MISS
		     replies, we'll only forward CLOSEST_PARENT_MISSes
		     and never FIRST_PARENT_MISSes.

		     use 'no-digest' to NOT request cache digests from
		     this neighbor.

		     'no-netdb-exchange' disables requesting ICMP
		     RTT database (NetDB) from the neighbor.

		     use 'no-delay' to prevent access to this neighbor
		     from influencing the delay pools.

		     use 'login=user:password' if this is a personal/workgroup
		     proxy and your parent requires proxy authentication.
		     Note: The string can include URL escapes (i.e. %20 for
		     spaces). This also means % must be written as %%.

		     use 'login=PASS' if users must authenticate against
		     the upstream proxy or in the case of a reverse proxy
		     configuration, the origin web server.  This will pass
		     the users credentials as they are to the peer.
		     This only works for the Basic HTTP authentication scheme.
		     Note: To combine this with proxy_auth both proxies must
		     share the same user database as HTTP only allows for
		     a single login (one for proxy, one for origin server).
		     Also be warned this will expose your users proxy
		     password to the peer. USE WITH CAUTION

		     use 'login=*:password' to pass the username to the
		     upstream cache, but with a fixed password. This is meant
		     to be used when the peer is in another administrative
		     domain, but it is still needed to identify each user.
		     The star can optionally be followed by some extra
		     information which is added to the username. This can
		     be used to identify this proxy to the peer, similar to
		     the login=username:password option above.

		     use 'connect-timeout=nn' to specify a peer
		     specific connect timeout (also see the
		     peer_connect_timeout directive)

		     use 'digest-url=url' to tell Squid to fetch the cache
		     digest (if digests are enabled) for this host from
		     the specified URL rather than the Squid default
		     location.

		     use 'allow-miss' to disable Squid's use of only-if-cached
		     when forwarding requests to siblings. This is primarily
		     useful when icp_hit_stale is used by the sibling. To
		     extensive use of this option may result in forwarding
		     loops, and you should avoid having two-way peerings
		     with this option. (for example to deny peer usage on
		     requests from peer by denying cache_peer_access if the
		     source is a peer)

		     use 'max-conn=n' to limit the amount of connections Squid
		     may open to this peer.

		     use 'htcp' to send HTCP, instead of ICP, queries
		     to the neighbor.  You probably also want to
		     set the "icp port" to 4827 instead of 3130.
		     You MUST also set htcp_access expicitly. The default of
		     deny all will prevent peer traffic.

		     use 'htcp-oldsquid' to send HTCP to old Squid versions
		     You MUST also set htcp_access expicitly. The default of
		     deny all will prevent peer traffic.		     

		     use 'htcp-no-clr' to send HTCP to the neighbor but without
		     sending any CLR requests.  This cannot be used with
		     htcp-only-clr.
		
		     use 'htcp-no-purge-clr' to send HTCP to the neighbor
		     including CLRs but only when they do not result from
		     PURGE requests.
		
		     use 'htcp-only-clr' to send HTCP to the neighbor but ONLY
		     CLR requests.  This cannot be used with htcp-no-clr.
		
		     use 'htcp-forward-clr' to forward any HTCP CLR requests
		     this proxy receives to the peer.

		     'originserver' causes this parent peer to be contacted as
		     a origin server. Meant to be used in accelerator setups.

		     use 'name=xxx' if you have multiple peers on the same
		     host but different ports. This name can be used to
		     differentiate the peers in cache_peer_access and similar
		     directives. Including the peername ACL type.

		     use 'forceddomain=name' to forcibly set the Host header
		     of requests forwarded to this peer. Useful in accelerator
		     setups where the server (peer) expects a certain domain
		     name and using redirectors to feed this domain name
		     is not feasible.

		     use 'ssl' to indicate connections to this peer should
		     be SSL/TLS encrypted.

		     use 'sslcert=/path/to/ssl/certificate' to specify a client
		     SSL certificate to use when connecting to this peer.

		     use 'sslkey=/path/to/ssl/key' to specify the private SSL
		     key corresponding to sslcert above. If 'sslkey' is not
		     specified 'sslcert' is assumed to reference a
		     combined file containing both the certificate and the key.

		     use sslversion=1|2|3|4 to specify the SSL version to use
		     when connecting to this peer
			1 = automatic (default)
			2 = SSL v2 only
			3 = SSL v3 only
			4 = TLS v1 only

		     use sslcipher=... to specify the list of valid SSL ciphers
		     to use when connecting to this peer.

		     use ssloptions=... to specify various SSL engine options:
			NO_SSLv2  Disallow the use of SSLv2
			NO_SSLv3  Disallow the use of SSLv3
			NO_TLSv1  Disallow the use of TLSv1
		     See src/ssl_support.c or the OpenSSL documentation for
		     a more complete list.

		     use sslcafile=... to specify a file containing
		     additional CA certificates to use when verifying the
		     peer certificate.

		     use sslcapath=... to specify a directory containing
		     additional CA certificates to use when verifying the
		     peer certificate.

		     use sslcrlfile=... to specify a certificate revocation
		     list file to use when verifying the peer certificate.
		     
		     use sslflags=... to specify various flags modifying the
		     SSL implementation:
			DONT_VERIFY_PEER
				Accept certificates even if they fail to
				verify.
			NO_DEFAULT_CA
				Don't use the default CA list built in
				to OpenSSL.
			DONT_VERIFY_DOMAIN
				Don't verify the peer certificate
				matches the server name

		     use ssldomain= to specify the peer name as advertised
		     in it's certificate. Used for verifying the correctness
		     of the received peer certificate. If not specified the
		     peer hostname will be used.

		     use front-end-https to enable the "Front-End-Https: On"
		     header needed when using Squid as a SSL frontend in front
		     of Microsoft OWA. See MS KB document Q307347 for details
		     on this header. If set to auto the header will
		     only be added if the request is forwarded as a https://
		     URL.
                     
                     use connection-auth=off to tell Squid that this peer does
                     not support Microsoft connection oriented authentication,
                     and any such challenges received from there should be
                     ignored. Default is auto to automatically determine the
                     status of the peer.
DOC_END

NAME: cache_peer_domain cache_host_domain
TYPE: hostdomain
DEFAULT: none
LOC: none
DOC_START
	Use to limit the domains for which a neighbor cache will be
	queried.  Usage:

	cache_peer_domain cache-host domain [domain ...]
	cache_peer_domain cache-host !domain

	For example, specifying

		cache_peer_domain parent.foo.net	.edu

	has the effect such that UDP query packets are sent to
	'bigserver' only when the requested object exists on a
	server in the .edu domain.  Prefixing the domainname
	with '!' means the cache will be queried for objects
	NOT in that domain.

	NOTE:	* Any number of domains may be given for a cache-host,
		  either on the same or separate lines.
		* When multiple domains are given for a particular
		  cache-host, the first matched domain is applied.
		* Cache hosts with no domain restrictions are queried
		  for all requests.
		* There are no defaults.
		* There is also a 'cache_peer_access' tag in the ACL
		  section.
DOC_END

NAME: cache_peer_access
TYPE: peer_access
DEFAULT: none
LOC: none
DOC_START
	Similar to 'cache_peer_domain' but provides more flexibility by
	using ACL elements.

	cache_peer_access cache-host allow|deny [!]aclname ...

	The syntax is identical to 'http_access' and the other lists of
	ACL elements.  See the comments for 'http_access' below, or
	the Squid FAQ (http://www.squid-cache.org/FAQ/FAQ-10.html).
DOC_END

NAME: neighbor_type_domain
TYPE: hostdomaintype
DEFAULT: none
LOC: none
DOC_START
	usage: neighbor_type_domain neighbor parent|sibling domain domain ...

	Modifying the neighbor type for specific domains is now
	possible.  You can treat some domains differently than the the
	default neighbor type specified on the 'cache_peer' line.
	Normally it should only be necessary to list domains which
	should be treated differently because the default neighbor type
	applies for hostnames which do not match domains listed here.

EXAMPLE:
	cache_peer cache.foo.org parent 3128 3130
	neighbor_type_domain cache.foo.org sibling .com .net
	neighbor_type_domain cache.foo.org sibling .au .de
DOC_END

NAME: dead_peer_timeout
COMMENT: (seconds)
DEFAULT: 10 seconds
TYPE: time_t
LOC: Config.Timeout.deadPeer
DOC_START
	This controls how long Squid waits to declare a peer cache
	as "dead."  If there are no ICP replies received in this
	amount of time, Squid will declare the peer dead and not
	expect to receive any further ICP replies.  However, it
	continues to send ICP queries, and will mark the peer as
	alive upon receipt of the first subsequent ICP reply.

	This timeout also affects when Squid expects to receive ICP
	replies from peers.  If more than 'dead_peer' seconds have
	passed since the last ICP reply was received, Squid will not
	expect to receive an ICP reply on the next query.  Thus, if
	your time between requests is greater than this timeout, you
	will see a lot of requests sent DIRECT to origin servers
	instead of to your parents.
DOC_END

NAME: hierarchy_stoplist
TYPE: wordlist
DEFAULT: none
LOC: Config.hierarchy_stoplist
DOC_START
	A list of words which, if found in a URL, cause the object to
	be handled directly by this cache.  In other words, use this
	to not query neighbor caches for certain objects.  You may
	list this option multiple times.
	Note: never_direct overrides this option.
NOCOMMENT_START
#We recommend you to use at least the following line.
hierarchy_stoplist cgi-bin ?
NOCOMMENT_END
DOC_END

COMMENT_START
 MEMORY CACHE OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: cache_mem
COMMENT: (bytes)
TYPE: b_size_t
DEFAULT: 256 MB
LOC: Config.memMaxSize
DOC_START
	NOTE: THIS PARAMETER DOES NOT SPECIFY THE MAXIMUM PROCESS SIZE.
	IT ONLY PLACES A LIMIT ON HOW MUCH ADDITIONAL MEMORY SQUID WILL
	USE AS A MEMORY CACHE OF OBJECTS. SQUID USES MEMORY FOR OTHER
	THINGS AS WELL. SEE THE SQUID FAQ SECTION 8 FOR DETAILS.

	'cache_mem' specifies the ideal amount of memory to be used
	for:
		* In-Transit objects
		* Hot Objects
		* Negative-Cached objects

	Data for these objects are stored in 4 KB blocks.  This
	parameter specifies the ideal upper limit on the total size of
	4 KB blocks allocated.  In-Transit objects take the highest
	priority.

	In-transit objects have priority over the others.  When
	additional space is needed for incoming data, negative-cached
	and hot objects will be released.  In other words, the
	negative-cached and hot objects will fill up any unused space
	not needed for in-transit objects.

	If circumstances require, this limit will be exceeded.
	Specifically, if your incoming request rate requires more than
	'cache_mem' of memory to hold in-transit objects, Squid will
	exceed this limit to satisfy the new requests.  When the load
	decreases, blocks will be freed until the high-water mark is
	reached.  Thereafter, blocks will be used to store hot
	objects.
DOC_END

NAME: maximum_object_size_in_memory
COMMENT: (bytes)
TYPE: b_size_t
DEFAULT: 512 KB
LOC: Config.Store.maxInMemObjSize
DOC_START
	Objects greater than this size will not be attempted to kept in
	the memory cache. This should be set high enough to keep objects
	accessed frequently in memory to improve performance whilst low
	enough to keep larger objects from hoarding cache_mem.
DOC_END

NAME: memory_replacement_policy
TYPE: removalpolicy
LOC: Config.memPolicy
DEFAULT: lru
DOC_START
	The memory replacement policy parameter determines which
	objects are purged from memory when memory space is needed.

	See cache_replacement_policy for details.
DOC_END

COMMENT_START
 DISK CACHE OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: cache_replacement_policy
TYPE: removalpolicy
LOC: Config.replPolicy
DEFAULT: lru
DOC_START
	The cache replacement policy parameter determines which
	objects are evicted (replaced) when disk space is needed.

	    lru       : Squid's original list based LRU policy
	    heap GDSF : Greedy-Dual Size Frequency
	    heap LFUDA: Least Frequently Used with Dynamic Aging
	    heap LRU  : LRU policy implemented using a heap

	Applies to any cache_dir lines listed below this.

	The LRU policies keeps recently referenced objects.

	The heap GDSF policy optimizes object hit rate by keeping smaller
	popular objects in cache so it has a better chance of getting a
	hit.  It achieves a lower byte hit rate than LFUDA though since
	it evicts larger (possibly popular) objects.

	The heap LFUDA policy keeps popular objects in cache regardless of
	their size and thus optimizes byte hit rate at the expense of
	hit rate since one large, popular object will prevent many
	smaller, slightly less popular objects from being cached.

	Both policies utilize a dynamic aging mechanism that prevents
	cache pollution that can otherwise occur with frequency-based
	replacement policies.

	NOTE: if using the LFUDA replacement policy you should increase
	the value of maximum_object_size above its default of 4096 KB to
	to maximize the potential byte hit rate improvement of LFUDA.

	For more information about the GDSF and LFUDA cache replacement
	policies see http://www.hpl.hp.com/techreports/1999/HPL-1999-69.html
	and http://fog.hpl.external.hp.com/techreports/98/HPL-98-173.html.
DOC_END

NAME: cache_dir
TYPE: cachedir
DEFAULT: none
LOC: Config.cacheSwap
DOC_START
	Usage:

	cache_dir Type Directory-Name Fs-specific-data [options]

	You can specify multiple cache_dir lines to spread the
	cache among different disk partitions.

	Type specifies the kind of storage system to use. Only "ufs"
	is built by default. To enable any of the other storage systems
	see the --enable-storeio configure option.

	'Directory' is a top-level directory where cache swap
	files will be stored.  If you want to use an entire disk
	for caching, this can be the mount-point directory.
	The directory must exist and be writable by the Squid
	process.  Squid will NOT create this directory for you.

	The ufs store type:

	"ufs" is the old well-known Squid storage format that has always
	been there.

	cache_dir ufs Directory-Name Mbytes L1 L2 [options]

	'Mbytes' is the amount of disk space (MB) to use under this
	directory.  The default is 100 MB.  Change this to suit your
	configuration.  Do NOT put the size of your disk drive here.
	Instead, if you want Squid to use the entire disk drive,
	subtract 20% and use that value.

	'Level-1' is the number of first-level subdirectories which
	will be created under the 'Directory'.  The default is 16.

	'Level-2' is the number of second-level subdirectories which
	will be created under each first-level directory.  The default
	is 256.

	The aufs store type:

	"aufs" uses the same storage format as "ufs", utilizing
	POSIX-threads to avoid blocking the main Squid process on
	disk-I/O. This was formerly known in Squid as async-io.

	cache_dir aufs Directory-Name Mbytes L1 L2 [options]

	see argument descriptions under ufs above

	The diskd store type:

	"diskd" uses the same storage format as "ufs", utilizing a
	separate process to avoid blocking the main Squid process on
	disk-I/O.

	cache_dir diskd Directory-Name Mbytes L1 L2 [options] [Q1=n] [Q2=n]

	see argument descriptions under ufs above

	Q1 specifies the number of unacknowledged I/O requests when Squid
	stops opening new files. If this many messages are in the queues,
	Squid won't open new files. Default is 64

	Q2 specifies the number of unacknowledged messages when Squid
	starts blocking.  If this many messages are in the queues,
	Squid blocks until it receives some replies. Default is 72

	When Q1 < Q2 (the default), the cache directory is optimized
	for lower response time at the expense of a decrease in hit
	ratio.  If Q1 > Q2, the cache directory is optimized for
	higher hit ratio at the expense of an increase in response
	time.

	The coss store type:

	block-size=n defines the "block size" for COSS cache_dir's.
	Squid uses file numbers as block numbers.  Since file numbers
	are limited to 24 bits, the block size determines the maximum
	size of the COSS partition.  The default is 512 bytes, which
	leads to a maximum cache_dir size of 512<<24, or 8 GB.  Note
	you should not change the coss block size after Squid
	has written some objects to the cache_dir.

	The coss file store has changed from 2.5. Now it uses a file
	called 'stripe' in the directory names in the config - and
	this will be created by squid -z.

	Common options:

	no-store, no new objects should be stored to this cache_dir

	max-size=n, refers to the max object size this storedir supports.
	It is used to initially choose the storedir to dump the object.
	Note: To make optimal use of the max-size limits you should order
	the cache_dir lines with the smallest max-size value first and the
	ones with no max-size specification last.

	Note for coss, max-size must be less than COSS_MEMBUF_SZ,
	which can be changed with the --with-coss-membuf-size=N configure
	option.
NOCOMMENT_START
# cache_dir ufs @DEFAULT_SWAP_DIR@ 100 16 256
NOCOMMENT_END
DOC_END

NAME: store_dir_select_algorithm
TYPE: string
LOC: Config.store_dir_select_algorithm
DEFAULT: least-load
DOC_START
	Set this to 'round-robin' as an alternative.
DOC_END

NAME: max_open_disk_fds
TYPE: int
LOC: Config.max_open_disk_fds
DEFAULT: 0
DOC_START
	To avoid having disk as the I/O bottleneck Squid can optionally
	bypass the on-disk cache if more than this amount of disk file
	descriptors are open.

	A value of 0 indicates no limit.
DOC_END

NAME: minimum_object_size
COMMENT: (bytes)
TYPE: b_int64_t
DEFAULT: 0 KB
LOC: Config.Store.minObjectSize
DOC_START
	Objects smaller than this size will NOT be saved on disk.  The
	value is specified in kilobytes, and the default is 0 KB, which
	means there is no minimum.
DOC_END

NAME: maximum_object_size
COMMENT: (bytes)
TYPE: b_int64_t
DEFAULT: 4096 KB
LOC: Config.Store.maxObjectSize
DOC_START
	Objects larger than this size will NOT be saved on disk.  The
	value is specified in kilobytes, and the default is 4MB.  If
	you wish to get a high BYTES hit ratio, you should probably
	increase this (one 32 MB object hit counts for 3200 10KB
	hits).  If you wish to increase speed more than your want to
	save bandwidth you should leave this low.

	NOTE: if using the LFUDA replacement policy you should increase
	this value to maximize the byte hit rate improvement of LFUDA!
	See replacement_policy below for a discussion of this policy.
DOC_END

NAME: cache_swap_low
COMMENT: (percent, 0-100)
TYPE: int
DEFAULT: 90
LOC: Config.Swap.lowWaterMark
DOC_NONE

NAME: cache_swap_high
COMMENT: (percent, 0-100)
TYPE: int
DEFAULT: 95
LOC: Config.Swap.highWaterMark
DOC_START

	The low- and high-water marks for cache object replacement.
	Replacement begins when the swap (disk) usage is above the
	low-water mark and attempts to maintain utilization near the
	low-water mark.  As swap utilization gets close to high-water
	mark object eviction becomes more aggressive.  If utilization is
	close to the low-water mark less replacement is done each time.

	Defaults are 90% and 95%. If you have a large cache, 5% could be
	hundreds of MB. If this is the case you may wish to set these
	numbers closer together.
DOC_END

COMMENT_START
 LOGFILE OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: logformat
TYPE: logformat
LOC: Config.Log.logformats
DEFAULT: none
DOC_START
	Usage:

	logformat <name> <format specification>

	Defines an access log format.

	The <format specification> is a string with embedded % format codes

	% format codes all follow the same basic structure where all but
	the formatcode is optional. Output strings are automatically escaped
	as required according to their context and the output format
	modifiers are usually not needed, but can be specified if an explicit
	output format is desired.

		% ["|[|'|#] [-] [[0]width] [{argument}] formatcode

		"	output in quoted string format
		[	output in squid text log format as used by log_mime_hdrs
		#	output in URL quoted format
		'	output as-is

		-	left aligned
		width	field width. If starting with 0 the
			output is zero padded
		{arg}	argument such as header name etc

	Format codes:

		>a	Client source IP address
		>A	Client FQDN
		>p	Client source port
		<A	Server IP address or peer name
		la	Local IP address (http_port)
		lp	Local port number (http_port)
		ts	Seconds since epoch
		tu	subsecond time (milliseconds)
		tl	Local time. Optional strftime format argument
			default %d/%b/%Y:%H:%M:%S %z
		tg	GMT time. Optional strftime format argument
			default %d/%b/%Y:%H:%M:%S %z
		tr	Response time (milliseconds)
		>h	Request header. Optional header name argument
			on the format header[:[separator]element]
		<h	Reply header. Optional header name argument
			as for >h
		un	User name
		ul	User name from authentication
		ui	User name from ident
		us	User name from SSL
		ue	User name from external acl helper
		Hs	HTTP status code
		Ss	Squid request status (TCP_MISS etc)
		Sh	Squid hierarchy status (DEFAULT_PARENT etc)
		mt	MIME content type
		rm	Request method (GET/POST etc)
		ru	Request URL
		rp	Request URL-Path excluding hostname
		rv	Request protocol version
		et	Tag returned by external acl
		ea	Log string returned by external acl
		<st	Reply size including HTTP headers
		>st	Request size including HTTP headers
		st	Request+Reply size including HTTP headers
		<sH	Reply high offset sent
		<sS	Upstream object size
		%	a literal % character

	The default formats available (which do not need re-defining) are:

logformat squid %ts.%03tu %6tr %>a %Ss/%03Hs %<st %rm %ru %un %Sh/%<A %mt
logformat squidmime %ts.%03tu %6tr %>a %Ss/%03Hs %<st %rm %ru %un %Sh/%<A %mt [%>h] [%<h]
logformat common %>a %ui %un [%tl] "%rm %ru HTTP/%rv" %Hs %<st %Ss:%Sh
logformat combined %>a %ui %un [%tl] "%rm %ru HTTP/%rv" %Hs %<st "%{Referer}>h" "%{User-Agent}>h" %Ss:%Sh
DOC_END

NAME: access_log cache_access_log
TYPE: access_log
LOC: Config.Log.accesslogs
DEFAULT: none
DEFAULT_IF_NONE: @DEFAULT_ACCESS_LOG@ squid
DOC_START
	These files log client request activities. Has a line every HTTP or
	ICP request. The format is:
	access_log <filepath> [<logformat name> [acl acl ...]]
	access_log none [acl acl ...]]

	Will log to the specified file using the specified format (which
	must be defined in a logformat directive) those entries which match
	ALL the acl's specified (which must be defined in acl clauses).
	If no acl is specified, all requests will be logged to this file.

	To disable logging of a request use the filepath "none", in which case
	a logformat name should not be specified.

	To log the request via syslog specify a filepath of "syslog":

	access_log syslog[:facility.priority] [format [acl1 [acl2 ....]]]
	where facility could be any of:
	authpriv, daemon, local0 .. local7 or user.

	And priority could be any of:
	err, warning, notice, info, debug.

	Default:
		access_log @DEFAULT_ACCESS_LOG@ squid
DOC_END

NAME: log_access
TYPE: acl_access
LOC: Config.accessList.log
DEFAULT: none
COMMENT: allow|deny acl acl...
DOC_START
	This options allows you to control which requests gets logged
	to access.log (see access_log directive). Requests denied for
	logging will also not be accounted for in performance counters.
DOC_END

NAME: cache_log
TYPE: string
DEFAULT: none
DEFAULT_IF_NONE: @DEFAULT_CACHE_LOG@
LOC: Config.Log.log
DOC_START
	Cache logging file. This is where general information about
	your cache's behavior goes. You can increase the amount of data
	logged to this file with the "debug_options" tag below.
DOC_END

NAME: cache_store_log
TYPE: string
DEFAULT: none
LOC: Config.Log.store
DOC_START
	Logs the activities of the storage manager.  Shows which
	objects are ejected from the cache, and which objects are
	saved and for how long.  To disable, enter "none" or remove the line.
	There are not really utilities to analyze this data, so you can safely
	disable it.
NOCOMMENT_START
# cache_store_log @DEFAULT_STORE_LOG@
NOCOMMENT_END
DOC_END

NAME: cache_swap_state cache_swap_log
TYPE: string
LOC: Config.Log.swap
DEFAULT: none
DOC_START
	Location for the cache "swap.state" file. This index file holds
	the metadata of objects saved on disk.  It is used to rebuild
	the cache during startup.  Normally this file resides in each
	'cache_dir' directory, but you may specify an alternate
	pathname here.  Note you must give a full filename, not just
	a directory. Since this is the index for the whole object
	list you CANNOT periodically rotate it!

	If %s can be used in the file name it will be replaced with a
	a representation of the cache_dir name where each / is replaced
	with '.'. This is needed to allow adding/removing cache_dir
	lines when cache_swap_log is being used.

	If have more than one 'cache_dir', and %s is not used in the name
	these swap logs will have names such as:

		cache_swap_log.00
		cache_swap_log.01
		cache_swap_log.02

	The numbered extension (which is added automatically)
	corresponds to the order of the 'cache_dir' lines in this
	configuration file.  If you change the order of the 'cache_dir'
	lines in this file, these index files will NOT correspond to
	the correct 'cache_dir' entry (unless you manually rename
	them).  We recommend you do NOT use this option.  It is
	better to keep these index files in each 'cache_dir' directory.
DOC_END

NAME: logfile_rotate
TYPE: int
DEFAULT: 10
LOC: Config.Log.rotateNumber
DOC_START
	Specifies the number of logfile rotations to make when you
	type 'squid -k rotate'. The default is 10, which will rotate
	with extensions 0 through 9. Setting logfile_rotate to 0 will
	disable the file name rotation, but the logfiles are still closed
	and re-opened. This will enable you to rename the logfiles
	yourself just before sending the rotate signal.

	Note, the 'squid -k rotate' command normally sends a USR1
	signal to the running squid process.  In certain situations
	(e.g. on Linux with Async I/O), USR1 is used for other
	purposes, so -k rotate uses another signal.  It is best to get
	in the habit of using 'squid -k rotate' instead of 'kill -USR1
	<pid>'.
DOC_END

NAME: emulate_httpd_log
COMMENT: on|off
TYPE: onoff
DEFAULT: off
LOC: Config.onoff.common_log
DOC_START
	The Cache can emulate the log file format which many 'httpd'
	programs use.  To disable/enable this emulation, set
	emulate_httpd_log to 'off' or 'on'.  The default
	is to use the native log format since it includes useful
	information Squid-specific log analyzers use.
DOC_END

NAME: log_ip_on_direct
COMMENT: on|off
TYPE: onoff
DEFAULT: on
LOC: Config.onoff.log_ip_on_direct
DOC_START
	Log the destination IP address in the hierarchy log tag when going
	direct. Earlier Squid versions logged the hostname here. If you
	prefer the old way set this to off.
DOC_END

NAME: mime_table
TYPE: string
DEFAULT: @DEFAULT_MIME_TABLE@
LOC: Config.mimeTablePathname
DOC_START
	Pathname to Squid's MIME table. You shouldn't need to change
	this, but the default file contains examples and formatting
	information if you do.
DOC_END

NAME: log_mime_hdrs
COMMENT: on|off
TYPE: onoff
LOC: Config.onoff.log_mime_hdrs
DEFAULT: off
DOC_START
	The Cache can record both the request and the response MIME
	headers for each HTTP transaction.  The headers are encoded
	safely and will appear as two bracketed fields at the end of
	the access log (for either the native or httpd-emulated log
	formats).  To enable this logging set log_mime_hdrs to 'on'.
DOC_END

NAME: useragent_log
TYPE: string
LOC: Config.Log.useragent
DEFAULT: none
IFDEF: USE_USERAGENT_LOG
DOC_START
	Squid will write the User-Agent field from HTTP requests
	to the filename specified here.  By default useragent_log
	is disabled.
DOC_END

NAME: referer_log referrer_log
TYPE: string
LOC: Config.Log.referer
DEFAULT: none
IFDEF: USE_REFERER_LOG
DOC_START
	Squid will write the Referer field from HTTP requests to the
	filename specified here.  By default referer_log is disabled.
	Note that "referer" is actually a misspelling of "referrer"
	however the misspelt version has been accepted into the HTTP RFCs
	and we accept both.
DOC_END

NAME: pid_filename
TYPE: string
DEFAULT: @DEFAULT_PID_FILE@
LOC: Config.pidFilename
DOC_START
	A filename to write the process-id to.  To disable, enter "none".
DOC_END

NAME: debug_options
TYPE: eol
DEFAULT: ALL,1
LOC: Config.debugOptions
DOC_START
	Logging options are set as section,level where each source file
	is assigned a unique section.  Lower levels result in less
	output,  Full debugging (level 9) can result in a very large
	log file, so be careful.  The magic word "ALL" sets debugging
	levels for all sections.  We recommend normally running with
	"ALL,1".
DOC_END

NAME: log_fqdn
COMMENT: on|off
TYPE: onoff
DEFAULT: off
LOC: Config.onoff.log_fqdn
DOC_START
	Turn this on if you wish to log fully qualified domain names
	in the access.log. To do this Squid does a DNS lookup of all
	IP's connecting to it. This can (in some situations) increase
	latency, which makes your cache seem slower for interactive
	browsing.
DOC_END

NAME: client_netmask
TYPE: address
LOC: Config.Addrs.client_netmask
DEFAULT: 255.255.255.255
DOC_START
	A netmask for client addresses in logfiles and cachemgr output.
	Change this to protect the privacy of your cache clients.
	A netmask of 255.255.255.0 will log all IP's in that range with
	the last digit set to '0'.
DOC_END

NAME: forward_log
IFDEF: WIP_FWD_LOG
TYPE: string
DEFAULT: none
LOC: Config.Log.forward
DOC_START
	Logs the server-side requests.

	This is currently work in progress.
DOC_END

NAME: strip_query_terms
TYPE: onoff
LOC: Config.onoff.strip_query_terms
DEFAULT: on
DOC_START
	By default, Squid strips query terms from requested URLs before
	logging.  This protects your user's privacy.
DOC_END

NAME: buffered_logs
COMMENT: on|off
TYPE: onoff
DEFAULT: off
LOC: Config.onoff.buffered_logs
DOC_START
	cache.log log file is written with stdio functions, and as such
	it can be buffered or unbuffered. By default it will be unbuffered.
	Buffering it can speed up the writing slightly (though you are
	unlikely to need to worry unless you run with tons of debugging
	enabled in which case performance will suffer badly anyway..).
DOC_END

NAME: netdb_filename
TYPE: string
DEFAULT: @DEFAULT_NETDB_FILE@
LOC: Config.netdbFilename
IFDEF: USE_ICMP
DOC_START
	A filename where Squid stores it's netdb state between restarts.
	To disable, enter "none".
DOC_END

COMMENT_START
 OPTIONS FOR FTP GATEWAYING
 -----------------------------------------------------------------------------
COMMENT_END

NAME: ftp_user
TYPE: string
DEFAULT: Squid@
LOC: Config.Ftp.anon_user
DOC_START
	If you want the anonymous login password to be more informative
	(and enable the use of picky ftp servers), set this to something
	reasonable for your domain, like wwwuser@somewhere.net

	The reason why this is domainless by default is the
	request can be made on the behalf of a user in any domain,
	depending on how the cache is used.
	Some ftp server also validate the email address is valid
	(for example perl.com).
DOC_END

NAME: ftp_list_width
TYPE: size_t
DEFAULT: 32
LOC: Config.Ftp.list_width
DOC_START
	Sets the width of ftp listings. This should be set to fit in
	the width of a standard browser. Setting this too small
	can cut off long filenames when browsing ftp sites.
DOC_END

NAME: ftp_passive
TYPE: onoff
DEFAULT: on
LOC: Config.Ftp.passive
DOC_START
	If your firewall does not allow Squid to use passive
	connections, turn off this option.

	Use of ftp_epsv_all option requires this to be ON.
DOC_END

NAME: ftp_epsv_all
TYPE: onoff
DEFAULT: off
LOC: Config.Ftp.epsv_all
DOC_START
	FTP Protocol extensions permit the use of a special "EPSV ALL" command.

	NATs may be able to put the connection on a "fast path" through the
	translator, as the EPRT command will never be used and therefore,
	translation of the data portion of the segments will never be needed.

	When a client only expects to do two-way FTP transfers this may be useful.
	If squid finds that it must do a three-way FTP transfer after issuing
	an EPSV ALL command, the FTP session will fail.

	If you have any doubts about this option do not use it.
	Squid will nicely attempt all other connection methods.

	Requires ftp_passive to be ON (default)
DOC_END

NAME: ftp_sanitycheck
TYPE: onoff
DEFAULT: on
LOC: Config.Ftp.sanitycheck
DOC_START
	For security and data integrity reasons Squid by default performs
	sanity checks of the addresses of FTP data connections ensure the
	data connection is to the requested server. If you need to allow
	FTP connections to servers using another IP address for the data
	connection turn this off.
DOC_END

NAME: ftp_telnet_protocol
TYPE: onoff
DEFAULT: on
LOC: Config.Ftp.telnet
DOC_START
	The FTP protocol is officially defined to use the telnet protocol
	as transport channel for the control connection. However, many
	implementations are broken and does not respect this aspect of
	the FTP protocol.

	If you have trouble accessing files with ASCII code 255 in the
	path or similar problems involving this ASCII code you can
	try setting this directive to off. If that helps, report to the
	operator of the FTP server in question that their FTP server
	is broken and does not follow the FTP standard.
DOC_END

COMMENT_START
 OPTIONS FOR EXTERNAL SUPPORT PROGRAMS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: diskd_program
TYPE: string
DEFAULT: @DEFAULT_DISKD@
LOC: Config.Program.diskd
DOC_START
	Specify the location of the diskd executable.
	Note this is only useful if you have compiled in
	diskd as one of the store io modules.
DOC_END

NAME: unlinkd_program
IFDEF: USE_UNLINKD
TYPE: string
DEFAULT: @DEFAULT_UNLINKD@
LOC: Config.Program.unlinkd
DOC_START
	Specify the location of the executable for file deletion process.
DOC_END

NAME: pinger_program
TYPE: string
DEFAULT: @DEFAULT_PINGER@
LOC: Config.pinger.program
IFDEF: USE_ICMP
DOC_START
	Specify the location of the executable for the pinger process.
DOC_END

NAME: pinger_enable
TYPE: onoff
DEFAULT: on
LOC: Config.pinger.enable
IFDEF: USE_ICMP
DOC_START
	Control whether the pinger is active at run-time.
	Enables turning ICMP pinger on and off with a simple squid -k reconfigure.
DOC_END


COMMENT_START
 OPTIONS FOR URL REWRITING
 -----------------------------------------------------------------------------
COMMENT_END

NAME: url_rewrite_program redirect_program
TYPE: wordlist
LOC: Config.Program.redirect
DEFAULT: none
DOC_START
	Specify the location of the executable for the URL rewriter.
	Since they can perform almost any function there isn't one included.

	For each requested URL rewriter will receive on line with the format

	URL <SP> client_ip "/" fqdn <SP> user <SP> method [<SP> kvpairs]<NL>

	In the future, the rewriter interface will be extended with
	key=value pairs ("kvpairs" shown above).  Rewriter programs
	should be prepared to receive and possibly ignore additional
	whitespace-separated tokens on each input line.

	And the rewriter may return a rewritten URL. The other components of
	the request line does not need to be returned (ignored if they are).

	The rewriter can also indicate that a client-side redirect should
	be performed to the new URL. This is done by prefixing the returned
	URL with "301:" (moved permanently) or 302: (moved temporarily).

	By default, a URL rewriter is not used.
DOC_END

NAME: url_rewrite_children redirect_children
TYPE: int
DEFAULT: 5
LOC: Config.redirectChildren
DOC_START
	The number of redirector processes to spawn. If you start
	too few Squid will have to wait for them to process a backlog of
	URLs, slowing it down. If you start too many they will use RAM
	and other system resources.
DOC_END

NAME: url_rewrite_concurrency redirect_concurrency
TYPE: int
DEFAULT: 0
LOC: Config.redirectConcurrency
DOC_START
	The number of requests each redirector helper can handle in
	parallel. Defaults to 0 which indicates the redirector
	is a old-style single threaded redirector.
DOC_END

NAME: url_rewrite_host_header redirect_rewrites_host_header
TYPE: onoff
DEFAULT: on
LOC: Config.onoff.redir_rewrites_host
DOC_START
	By default Squid rewrites any Host: header in redirected
	requests.  If you are running an accelerator this may
	not be a wanted effect of a redirector.

	WARNING: Entries are cached on the result of the URL rewriting
	process, so be careful if you have domain-virtual hosts.
DOC_END

NAME: url_rewrite_access redirector_access
TYPE: acl_access
DEFAULT: none
LOC: Config.accessList.redirector
DOC_START
	If defined, this access list specifies which requests are
	sent to the redirector processes.  By default all requests
	are sent.
DOC_END

NAME: url_rewrite_bypass redirector_bypass
TYPE: onoff
LOC: Config.onoff.redirector_bypass
DEFAULT: off
DOC_START
	When this is 'on', a request will not go through the
	redirector if all redirectors are busy.  If this is 'off'
	and the redirector queue grows too large, Squid will exit
	with a FATAL error and ask you to increase the number of
	redirectors.  You should only enable this if the redirectors
	are not critical to your caching system.  If you use
	redirectors for access control, and you enable this option,
	users may have access to pages they should not
	be allowed to request.
DOC_END

COMMENT_START
 OPTIONS FOR TUNING THE CACHE
 -----------------------------------------------------------------------------
COMMENT_END

NAME: cache no_cache
TYPE: acl_access
DEFAULT: none
LOC: Config.accessList.noCache
DOC_START
	A list of ACL elements which, if matched and denied, cause the request to
	not be satisfied from the cache and the reply to not be cached.
	In other words, use this to force certain objects to never be cached.

	You must use the words 'allow' or 'deny' to indicate whether items
	matching the ACL should be allowed or denied into the cache.

	Default is to allow all to be cached.
DOC_END

NAME: refresh_pattern
TYPE: refreshpattern
LOC: Config.Refresh
DEFAULT: none
DOC_START
	usage: refresh_pattern [-i] regex min percent max [options]

	By default, regular expressions are CASE-SENSITIVE.  To make
	them case-insensitive, use the -i option.

	'Min' is the time (in minutes) an object without an explicit
	expiry time should be considered fresh. The recommended
	value is 0, any higher values may cause dynamic applications
	to be erroneously cached unless the application designer
	has taken the appropriate actions.

	'Percent' is a percentage of the objects age (time since last
	modification age) an object without explicit expiry time
	will be considered fresh.

	'Max' is an upper limit on how long objects without an explicit
	expiry time will be considered fresh.

	options: override-expire
		 override-lastmod
		 reload-into-ims
		 ignore-reload
		 ignore-no-cache
		 ignore-no-store
		 ignore-private
		 ignore-auth
		 refresh-ims

		override-expire enforces min age even if the server
		sent an explicit expiry time (e.g., with the
		Expires: header or Cache-Control: max-age). Doing this
		VIOLATES the HTTP standard.  Enabling this feature
		could make you liable for problems which it causes.

		override-lastmod enforces min age even on objects
		that were modified recently.

		reload-into-ims changes client no-cache or ``reload''
		to If-Modified-Since requests. Doing this VIOLATES the
		HTTP standard. Enabling this feature could make you
		liable for problems which it causes.

		ignore-reload ignores a client no-cache or ``reload''
		header. Doing this VIOLATES the HTTP standard. Enabling
		this feature could make you liable for problems which
		it causes.

		ignore-no-cache ignores any ``Pragma: no-cache'' and
		``Cache-control: no-cache'' headers received from a server.
		The HTTP RFC never allows the use of this (Pragma) header
		from a server, only a client, though plenty of servers
		send it anyway.

		ignore-no-store ignores any ``Cache-control: no-store''
		headers received from a server. Doing this VIOLATES
		the HTTP standard. Enabling this feature could make you
		liable for problems which it causes.

		ignore-private ignores any ``Cache-control: private''
		headers received from a server. Doing this VIOLATES
		the HTTP standard. Enabling this feature could make you
		liable for problems which it causes.

		ignore-auth caches responses to requests with authorization,
		as if the originserver had sent ``Cache-control: public''
		in the response header. Doing this VIOLATES the HTTP standard.
		Enabling this feature could make you liable for problems which
		it causes.

		refresh-ims causes squid to contact the origin server
		when a client issues an If-Modified-Since request. This
		ensures that the client will receive an updated version
		if one is available.

	Basically a cached object is:

		FRESH if expires < now, else STALE
		STALE if age > max
		FRESH if lm-factor < percent, else STALE
		FRESH if age < min
		else STALE

	The refresh_pattern lines are checked in the order listed here.
	The first entry which matches is used.  If none of the entries
	match the default will be used.

	Note, you must uncomment all the default lines if you want
	to change one. The default setting is only active if none is
	used.

Suggested default:
NOCOMMENT_START
refresh_pattern ^ftp:		1440	20%	10080
refresh_pattern ^gopher:	1440	0%	1440
refresh_pattern -i (/cgi-bin/|\?) 0	0%	0
refresh_pattern .		0	20%	4320
NOCOMMENT_END
DOC_END

NAME: quick_abort_min
COMMENT: (KB)
TYPE: kb_int64_t
DEFAULT: 16 KB
LOC: Config.quickAbort.min
DOC_NONE

NAME: quick_abort_max
COMMENT: (KB)
TYPE: kb_int64_t
DEFAULT: 16 KB
LOC: Config.quickAbort.max
DOC_NONE

NAME: quick_abort_pct
COMMENT: (percent)
TYPE: int
DEFAULT: 95
LOC: Config.quickAbort.pct
DOC_START
	The cache by default continues downloading aborted requests
	which are almost completed (less than 16 KB remaining). This
	may be undesirable on slow (e.g. SLIP) links and/or very busy
	caches.  Impatient users may tie up file descriptors and
	bandwidth by repeatedly requesting and immediately aborting
	downloads.

	When the user aborts a request, Squid will check the
	quick_abort values to the amount of data transfered until
	then.

	If the transfer has less than 'quick_abort_min' KB remaining,
	it will finish the retrieval.

	If the transfer has more than 'quick_abort_max' KB remaining,
	it will abort the retrieval.

	If more than 'quick_abort_pct' of the transfer has completed,
	it will finish the retrieval.

	If you do not want any retrieval to continue after the client
	has aborted, set both 'quick_abort_min' and 'quick_abort_max'
	to '0 KB'.

	If you want retrievals to always continue if they are being
	cached set 'quick_abort_min' to '-1 KB'.
DOC_END

NAME: read_ahead_gap
COMMENT: buffer-size
TYPE: b_int64_t
LOC: Config.readAheadGap
DEFAULT: 16 KB
DOC_START
	The amount of data the cache will buffer ahead of what has been
	sent to the client when retrieving an object from another server.
DOC_END

NAME: negative_ttl
IFDEF: HTTP_VIOLATIONS
COMMENT: time-units
TYPE: time_t
LOC: Config.negativeTtl
DEFAULT: 0 seconds
DOC_START
	Set the Default Time-to-Live (TTL) for failed requests.
	Certain types of failures (such as "connection refused" and
	"404 Not Found") are able to be negatively-cached for a short time.
	Modern web servers should provide Expires: header, however if they
	do not this can provide a minimum TTL.
	The default is not to cache errors with unknown expiry details.

	Note that this is different from negative caching of DNS lookups.

	WARNING: Doing this VIOLATES the HTTP standard.  Enabling
	this feature could make you liable for problems which it
	causes.
DOC_END

NAME: positive_dns_ttl
COMMENT: time-units
TYPE: time_t
LOC: Config.positiveDnsTtl
DEFAULT: 6 hours
DOC_START
	Upper limit on how long Squid will cache positive DNS responses.
	Default is 6 hours (360 minutes). This directive must be set
	larger than negative_dns_ttl.
DOC_END

NAME: negative_dns_ttl
COMMENT: time-units
TYPE: time_t
LOC: Config.negativeDnsTtl
DEFAULT: 1 minutes
DOC_START
	Time-to-Live (TTL) for negative caching of failed DNS lookups.
	This also sets the lower cache limit on positive lookups.
	Minimum value is 1 second, and it is not recommendable to go
	much below 10 seconds.
DOC_END

NAME: range_offset_limit
COMMENT: (bytes)
TYPE: b_int64_t
LOC: Config.rangeOffsetLimit
DEFAULT: 0 KB
DOC_START
	Sets a upper limit on how far into the the file a Range request
	may be to cause Squid to prefetch the whole file. If beyond this
	limit Squid forwards the Range request as it is and the result
	is NOT cached.

	This is to stop a far ahead range request (lets say start at 17MB)
	from making Squid fetch the whole object up to that point before
	sending anything to the client.

	A value of -1 causes Squid to always fetch the object from the
	beginning so it may cache the result. (2.0 style)

	A value of 0 causes Squid to never fetch more than the
	client requested. (default)
DOC_END

NAME: minimum_expiry_time
COMMENT: (seconds)
TYPE: time_t
LOC: Config.minimum_expiry_time
DEFAULT: 60 seconds
DOC_START
	The minimum caching time according to (Expires - Date)
	Headers Squid honors if the object can't be revalidated
	defaults to 60 seconds. In reverse proxy environments it
	might be desirable to honor shorter object lifetimes. It
	is most likely better to make your server return a
	meaningful Last-Modified header however. In ESI environments
	where page fragments often have short lifetimes, this will
	often be best set to 0.
DOC_END

NAME: store_avg_object_size
COMMENT: (kbytes)
TYPE: kb_int64_t
DEFAULT: 13 KB
LOC: Config.Store.avgObjectSize
DOC_START
	Average object size, used to estimate number of objects your
	cache can hold.  The default is 13 KB.
DOC_END

NAME: store_objects_per_bucket
TYPE: int
DEFAULT: 20
LOC: Config.Store.objectsPerBucket
DOC_START
	Target number of objects per bucket in the store hash table.
	Lowering this value increases the total number of buckets and
	also the storage maintenance rate.  The default is 20.
DOC_END

COMMENT_START
 HTTP OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: request_header_max_size
COMMENT: (KB)
TYPE: b_size_t
DEFAULT: 64 KB
LOC: Config.maxRequestHeaderSize
DOC_START
	This specifies the maximum size for HTTP headers in a request.
	Request headers are usually relatively small (about 512 bytes).
	Placing a limit on the request header size will catch certain
	bugs (for example with persistent connections) and possibly
	buffer-overflow or denial-of-service attacks.
DOC_END

NAME: reply_header_max_size
COMMENT: (KB)
TYPE: b_size_t
DEFAULT: 64 KB
LOC: Config.maxReplyHeaderSize
DOC_START
	This specifies the maximum size for HTTP headers in a reply.
	Reply headers are usually relatively small (about 512 bytes).
	Placing a limit on the reply header size will catch certain
	bugs (for example with persistent connections) and possibly
	buffer-overflow or denial-of-service attacks.
DOC_END

NAME: request_body_max_size
COMMENT: (bytes)
TYPE: b_int64_t
DEFAULT: 0 KB
LOC: Config.maxRequestBodySize
DOC_START
	This specifies the maximum size for an HTTP request body.
	In other words, the maximum size of a PUT/POST request.
	A user who attempts to send a request with a body larger
	than this limit receives an "Invalid Request" error message.
	If you set this parameter to a zero (the default), there will
	be no limit imposed.
DOC_END

NAME: broken_posts
TYPE: acl_access
DEFAULT: none
LOC: Config.accessList.brokenPosts
DOC_START
	A list of ACL elements which, if matched, causes Squid to send
	an extra CRLF pair after the body of a PUT/POST request.

	Some HTTP servers has broken implementations of PUT/POST,
	and rely on an extra CRLF pair sent by some WWW clients.

	Quote from RFC2616 section 4.1 on this matter:

	  Note: certain buggy HTTP/1.0 client implementations generate an
	  extra CRLF's after a POST request. To restate what is explicitly
	  forbidden by the BNF, an HTTP/1.1 client must not preface or follow
	  a request with an extra CRLF.

Example:
 acl buggy_server url_regex ^http://....
 broken_posts allow buggy_server
DOC_END

NAME: via
IFDEF: HTTP_VIOLATIONS
COMMENT: on|off
TYPE: onoff
DEFAULT: on
LOC: Config.onoff.via
DOC_START
	If set (default), Squid will include a Via header in requests and
	replies as required by RFC2616.
DOC_END

NAME: ie_refresh
COMMENT: on|off
TYPE: onoff
LOC: Config.onoff.ie_refresh
DEFAULT: off
DOC_START
	Microsoft Internet Explorer up until version 5.5 Service
	Pack 1 has an issue with transparent proxies, wherein it
	is impossible to force a refresh.  Turning this on provides
	a partial fix to the problem, by causing all IMS-REFRESH
	requests from older IE versions to check the origin server
	for fresh content.  This reduces hit ratio by some amount
	(~10% in my experience), but allows users to actually get
	fresh content when they want it.  Note because Squid
	cannot tell if the user is using 5.5 or 5.5SP1, the behavior
	of 5.5 is unchanged from old versions of Squid (i.e. a
	forced refresh is impossible).  Newer versions of IE will,
	hopefully, continue to have the new behavior and will be
	handled based on that assumption.  This option defaults to
	the old Squid behavior, which is better for hit ratios but
	worse for clients using IE, if they need to be able to
	force fresh content.
DOC_END

NAME: vary_ignore_expire
COMMENT: on|off
TYPE: onoff
LOC: Config.onoff.vary_ignore_expire
DEFAULT: off
DOC_START
	Many HTTP servers supporting Vary gives such objects
	immediate expiry time with no cache-control header
	when requested by a HTTP/1.0 client. This option
	enables Squid to ignore such expiry times until
	HTTP/1.1 is fully implemented.
	WARNING: This may eventually cause some varying
	objects not intended for caching to get cached.
DOC_END

NAME: request_entities
TYPE: onoff
LOC: Config.onoff.request_entities
DEFAULT: off
DOC_START
	Squid defaults to deny GET and HEAD requests with request entities,
	as the meaning of such requests are undefined in the HTTP standard
	even if not explicitly forbidden.

	Set this directive to on if you have clients which insists
	on sending request entities in GET or HEAD requests. But be warned
	that there is server software (both proxies and web servers) which
	can fail to properly process this kind of request which may make you
	vulnerable to cache pollution attacks if enabled.
DOC_END

NAME: request_header_access
IFDEF: HTTP_VIOLATIONS
TYPE: http_header_access[]
LOC: Config.request_header_access
DEFAULT: none
DOC_START
	Usage: request_header_access header_name allow|deny [!]aclname ...

	WARNING: Doing this VIOLATES the HTTP standard.  Enabling
	this feature could make you liable for problems which it
	causes.

	This option replaces the old 'anonymize_headers' and the
	older 'http_anonymizer' option with something that is much
	more configurable. This new method creates a list of ACLs
	for each header, allowing you very fine-tuned header
	mangling.

	This option only applies to request headers, i.e., from the
	client to the server.

	You can only specify known headers for the header name.
	Other headers are reclassified as 'Other'. You can also
	refer to all the headers with 'All'.

	For example, to achieve the same behavior as the old
	'http_anonymizer standard' option, you should use:

		request_header_access From deny all
		request_header_access Referer deny all
		request_header_access Server deny all
		request_header_access User-Agent deny all
		request_header_access WWW-Authenticate deny all
		request_header_access Link deny all

	Or, to reproduce the old 'http_anonymizer paranoid' feature
	you should use:

		request_header_access Allow allow all
		request_header_access Authorization allow all
		request_header_access WWW-Authenticate allow all
		request_header_access Proxy-Authorization allow all
		request_header_access Proxy-Authenticate allow all
		request_header_access Cache-Control allow all
		request_header_access Content-Encoding allow all
		request_header_access Content-Length allow all
		request_header_access Content-Type allow all
		request_header_access Date allow all
		request_header_access Expires allow all
		request_header_access Host allow all
		request_header_access If-Modified-Since allow all
		request_header_access Last-Modified allow all
		request_header_access Location allow all
		request_header_access Pragma allow all
		request_header_access Accept allow all
		request_header_access Accept-Charset allow all
		request_header_access Accept-Encoding allow all
		request_header_access Accept-Language allow all
		request_header_access Content-Language allow all
		request_header_access Mime-Version allow all
		request_header_access Retry-After allow all
		request_header_access Title allow all
		request_header_access Connection allow all
		request_header_access Proxy-Connection allow all
		request_header_access All deny all

	although many of those are HTTP reply headers, and so should be
	controlled with the reply_header_access directive.

	By default, all headers are allowed (no anonymizing is
	performed).
DOC_END

NAME: reply_header_access
IFDEF: HTTP_VIOLATIONS
TYPE: http_header_access[]
LOC: Config.reply_header_access
DEFAULT: none
DOC_START
	Usage: reply_header_access header_name allow|deny [!]aclname ...

	WARNING: Doing this VIOLATES the HTTP standard.  Enabling
	this feature could make you liable for problems which it
	causes.

	This option only applies to reply headers, i.e., from the
	server to the client.

	This is the same as request_header_access, but in the other
	direction.

	This option replaces the old 'anonymize_headers' and the
	older 'http_anonymizer' option with something that is much
	more configurable. This new method creates a list of ACLs
	for each header, allowing you very fine-tuned header
	mangling.

	You can only specify known headers for the header name.
	Other headers are reclassified as 'Other'. You can also
	refer to all the headers with 'All'.

	For example, to achieve the same behavior as the old
	'http_anonymizer standard' option, you should use:

		reply_header_access From deny all
		reply_header_access Referer deny all
		reply_header_access Server deny all
		reply_header_access User-Agent deny all
		reply_header_access WWW-Authenticate deny all
		reply_header_access Link deny all

	Or, to reproduce the old 'http_anonymizer paranoid' feature
	you should use:

		reply_header_access Allow allow all
		reply_header_access Authorization allow all
		reply_header_access WWW-Authenticate allow all
		reply_header_access Proxy-Authorization allow all
		reply_header_access Proxy-Authenticate allow all
		reply_header_access Cache-Control allow all
		reply_header_access Content-Encoding allow all
		reply_header_access Content-Length allow all
		reply_header_access Content-Type allow all
		reply_header_access Date allow all
		reply_header_access Expires allow all
		reply_header_access Host allow all
		reply_header_access If-Modified-Since allow all
		reply_header_access Last-Modified allow all
		reply_header_access Location allow all
		reply_header_access Pragma allow all
		reply_header_access Accept allow all
		reply_header_access Accept-Charset allow all
		reply_header_access Accept-Encoding allow all
		reply_header_access Accept-Language allow all
		reply_header_access Content-Language allow all
		reply_header_access Mime-Version allow all
		reply_header_access Retry-After allow all
		reply_header_access Title allow all
		reply_header_access Connection allow all
		reply_header_access Proxy-Connection allow all
		reply_header_access All deny all

	although the HTTP request headers won't be usefully controlled
	by this directive -- see request_header_access for details.

	By default, all headers are allowed (no anonymizing is
	performed).
DOC_END

NAME: header_replace
IFDEF: HTTP_VIOLATIONS
TYPE: http_header_replace[]
LOC: Config.request_header_access
DEFAULT: none
DOC_START
	Usage:   header_replace header_name message
	Example: header_replace User-Agent Nutscrape/1.0 (CP/M; 8-bit)

	This option allows you to change the contents of headers
	denied with header_access above, by replacing them with
	some fixed string. This replaces the old fake_user_agent
	option.

	This only applies to request headers, not reply headers.

	By default, headers are removed if denied.
DOC_END

NAME: relaxed_header_parser
COMMENT: on|off|warn
TYPE: tristate
LOC: Config.onoff.relaxed_header_parser
DEFAULT: on
DOC_START
	In the default "on" setting Squid accepts certain forms
	of non-compliant HTTP messages where it is unambiguous
	what the sending application intended even if the message
	is not correctly formatted. The messages is then normalized
	to the correct form when forwarded by Squid.

	If set to "warn" then a warning will be emitted in cache.log
	each time such HTTP error is encountered.

	If set to "off" then such HTTP errors will cause the request
	or response to be rejected.
DOC_END

COMMENT_START
 TIMEOUTS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: forward_timeout
COMMENT: time-units
TYPE: time_t
LOC: Config.Timeout.forward
DEFAULT: 4 minutes
DOC_START
	This parameter specifies how long Squid should at most attempt in
	finding a forwarding path for the request before giving up.
DOC_END

NAME: connect_timeout
COMMENT: time-units
TYPE: time_t
LOC: Config.Timeout.connect
DEFAULT: 1 minute
DOC_START
	This parameter specifies how long to wait for the TCP connect to
	the requested server or peer to complete before Squid should
	attempt to find another path where to forward the request.
DOC_END

NAME: peer_connect_timeout
COMMENT: time-units
TYPE: time_t
LOC: Config.Timeout.peer_connect
DEFAULT: 30 seconds
DOC_START
	This parameter specifies how long to wait for a pending TCP
	connection to a peer cache.  The default is 30 seconds.   You
	may also set different timeout values for individual neighbors
	with the 'connect-timeout' option on a 'cache_peer' line.
DOC_END

NAME: read_timeout
COMMENT: time-units
TYPE: time_t
LOC: Config.Timeout.read
DEFAULT: 15 minutes
DOC_START
	The read_timeout is applied on server-side connections.  After
	each successful read(), the timeout will be extended by this
	amount.  If no data is read again after this amount of time,
	the request is aborted and logged with ERR_READ_TIMEOUT.  The
	default is 15 minutes.
DOC_END

NAME: request_timeout
TYPE: time_t
LOC: Config.Timeout.request
DEFAULT: 5 minutes
DOC_START
	How long to wait for an HTTP request after initial
	connection establishment.
DOC_END

NAME: persistent_request_timeout
TYPE: time_t
LOC: Config.Timeout.persistent_request
DEFAULT: 2 minutes
DOC_START
	How long to wait for the next HTTP request on a persistent
	connection after the previous request completes.
DOC_END

NAME: client_lifetime
COMMENT: time-units
TYPE: time_t
LOC: Config.Timeout.lifetime
DEFAULT: 1 day
DOC_START
	The maximum amount of time a client (browser) is allowed to
	remain connected to the cache process.  This protects the Cache
	from having a lot of sockets (and hence file descriptors) tied up
	in a CLOSE_WAIT state from remote clients that go away without
	properly shutting down (either because of a network failure or
	because of a poor client implementation).  The default is one
	day, 1440 minutes.

	NOTE:  The default value is intended to be much larger than any
	client would ever need to be connected to your cache.  You
	should probably change client_lifetime only as a last resort.
	If you seem to have many client connections tying up
	filedescriptors, we recommend first tuning the read_timeout,
	request_timeout, persistent_request_timeout and quick_abort values.
DOC_END

NAME: half_closed_clients
TYPE: onoff
LOC: Config.onoff.half_closed_clients
DEFAULT: on
DOC_START
	Some clients may shutdown the sending side of their TCP
	connections, while leaving their receiving sides open.	Sometimes,
	Squid can not tell the difference between a half-closed and a
	fully-closed TCP connection.  By default, half-closed client
	connections are kept open until a read(2) or write(2) on the
	socket returns an error.  Change this option to 'off' and Squid
	will immediately close client connections when read(2) returns
	"no more data to read."
DOC_END

NAME: pconn_timeout
TYPE: time_t
LOC: Config.Timeout.pconn
DEFAULT: 1 minute
DOC_START
	Timeout for idle persistent connections to servers and other
	proxies.
DOC_END

NAME: ident_timeout
TYPE: time_t
IFDEF: USE_IDENT
LOC: Config.Timeout.ident
DEFAULT: 10 seconds
DOC_START
	Maximum time to wait for IDENT lookups to complete.

	If this is too high, and you enabled IDENT lookups from untrusted
	users, you might be susceptible to denial-of-service by having
	many ident requests going at once.
DOC_END

NAME: shutdown_lifetime
COMMENT: time-units
TYPE: time_t
LOC: Config.shutdownLifetime
DEFAULT: 30 seconds
DOC_START
	When SIGTERM or SIGHUP is received, the cache is put into
	"shutdown pending" mode until all active sockets are closed.
	This value is the lifetime to set for all open descriptors
	during shutdown mode.  Any active clients after this many
	seconds will receive a 'timeout' message.
DOC_END

COMMENT_START
 ADMINISTRATIVE PARAMETERS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: cache_mgr
TYPE: string
DEFAULT: webmaster
LOC: Config.adminEmail
DOC_START
	Email-address of local cache manager who will receive
	mail if the cache dies.  The default is "webmaster."
DOC_END

NAME: mail_from
TYPE: string
DEFAULT: none
LOC: Config.EmailFrom
DOC_START
	From: email-address for mail sent when the cache dies.
	The default is to use 'appname@unique_hostname'.
	Default appname value is "squid", can be changed into
	src/globals.h before building squid.
DOC_END

NAME: mail_program
TYPE: eol
DEFAULT: mail
LOC: Config.EmailProgram
DOC_START
	Email program used to send mail if the cache dies.
	The default is "mail". The specified program must comply
	with the standard Unix mail syntax:
	  mail-program recipient < mailfile

	Optional command line options can be specified.
DOC_END

NAME: cache_effective_user
TYPE: string
DEFAULT: @DEFAULT_CACHE_EFFECTIVE_USER@
LOC: Config.effectiveUser
DOC_START
	If you start Squid as root, it will change its effective/real
	UID/GID to the user specified below.  The default is to change
	to UID of @DEFAULT_CACHE_EFFECTIVE_USER@.
	see also; cache_effective_group
DOC_END

NAME: cache_effective_group
TYPE: string
DEFAULT: none
LOC: Config.effectiveGroup
DOC_START
	Squid sets the GID to the effective user's default group ID
	(taken from the password file) and supplementary group list
	from the groups membership.

	If you want Squid to run with a specific GID regardless of
	the group memberships of the effective user then set this
	to the group (or GID) you want Squid to run as. When set
	all other group privileges of the effective user are ignored
	and only this GID is effective. If Squid is not started as
	root the user starting Squid MUST be member of the specified
	group.

	This option is not recommended by the Squid Team.
	Our preference is for administrators to configure a secure
	user account for squid with UID/GID matching system policies.
DOC_END

NAME: httpd_suppress_version_string
COMMENT: on|off
TYPE: onoff
DEFAULT: off
LOC: Config.onoff.httpd_suppress_version_string
DOC_START
	Suppress Squid version string info in HTTP headers and HTML error pages.
DOC_END

NAME: visible_hostname
TYPE: string
LOC: Config.visibleHostname
DEFAULT: none
DOC_START
	If you want to present a special hostname in error messages, etc,
	define this.  Otherwise, the return value of gethostname()
	will be used. If you have multiple caches in a cluster and
	get errors about IP-forwarding you must set them to have individual
	names with this setting.
DOC_END

NAME: unique_hostname
TYPE: string
LOC: Config.uniqueHostname
DEFAULT: none
DOC_START
	If you want to have multiple machines with the same
	'visible_hostname' you must give each machine a different
	'unique_hostname' so forwarding loops can be detected.
DOC_END

NAME: hostname_aliases
TYPE: wordlist
LOC: Config.hostnameAliases
DEFAULT: none
DOC_START
	A list of other DNS names your cache has.
DOC_END

NAME: umask
TYPE: int
LOC: Config.umask
DEFAULT: 027
DOC_START
	Minimum umask which should be enforced while the proxy
	is running, in addition to the umask set at startup.

	For a traditional octal representation of umasks, start
        your value with 0.
DOC_END

COMMENT_START
 OPTIONS FOR THE CACHE REGISTRATION SERVICE
 -----------------------------------------------------------------------------

	This section contains parameters for the (optional) cache
	announcement service.  This service is provided to help
	cache administrators locate one another in order to join or
	create cache hierarchies.

	An 'announcement' message is sent (via UDP) to the registration
	service by Squid.  By default, the announcement message is NOT
	SENT unless you enable it with 'announce_period' below.

	The announcement message includes your hostname, plus the
	following information from this configuration file:

		http_port
		icp_port
		cache_mgr

	All current information is processed regularly and made
	available on the Web at http://www.ircache.net/Cache/Tracker/.
COMMENT_END

NAME: announce_period
TYPE: time_t
LOC: Config.Announce.period
DEFAULT: 0
DOC_START
	This is how frequently to send cache announcements.  The
	default is `0' which disables sending the announcement
	messages.

	To enable announcing your cache, just uncomment the line
	below.

NOCOMMENT_START
#To enable announcing your cache, just uncomment the line below.
#announce_period 1 day
NOCOMMENT_END
DOC_END

NAME: announce_host
TYPE: string
DEFAULT: tracker.ircache.net
LOC: Config.Announce.host
DOC_NONE

NAME: announce_file
TYPE: string
DEFAULT: none
LOC: Config.Announce.file
DOC_NONE

NAME: announce_port
TYPE: ushort
DEFAULT: 3131
LOC: Config.Announce.port
DOC_START
	announce_host and announce_port set the hostname and port
	number where the registration message will be sent.

	Hostname will default to 'tracker.ircache.net' and port will
	default default to 3131.  If the 'filename' argument is given,
	the contents of that file will be included in the announce
	message.
DOC_END

COMMENT_START
 HTTPD-ACCELERATOR OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: httpd_accel_surrogate_id
IFDEF: USE_SQUID_ESI
TYPE:  string
LOC: Config.Accel.surrogate_id
DEFAULT: unset-id
DOC_START
	Surrogates (http://www.esi.org/architecture_spec_1.0.html)
	need an identification token to allow control targeting. Because
	a farm of surrogates may all perform the same tasks, they may share
	an identification token.
DOC_END

NAME: http_accel_surrogate_remote
IFDEF: USE_SQUID_ESI
COMMENT: on|off
TYPE: onoff
DEFAULT: off
LOC: Config.onoff.surrogate_is_remote
DOC_START
	Remote surrogates (such as those in a CDN) honour Surrogate-Control: no-store-remote.
	Set this to on to have squid behave as a remote surrogate.
DOC_END

NAME: esi_parser
IFDEF: USE_SQUID_ESI
COMMENT: libxml2|expat|custom
TYPE: string
LOC: ESIParser::Type
DEFAULT: custom
DOC_START
	ESI markup is not strictly XML compatible. The custom ESI parser
	will give higher performance, but cannot handle non ASCII character
	encodings.
DOC_END

COMMENT_START
 DELAY POOL PARAMETERS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: delay_pools
TYPE: delay_pool_count
DEFAULT: 0
IFDEF: DELAY_POOLS
LOC: Config.Delay
DOC_START
	This represents the number of delay pools to be used.  For example,
	if you have one class 2 delay pool and one class 3 delays pool, you
	have a total of 2 delay pools.
DOC_END

NAME: delay_class
TYPE: delay_pool_class
DEFAULT: none
IFDEF: DELAY_POOLS
LOC: Config.Delay
DOC_START
	This defines the class of each delay pool.  There must be exactly one
	delay_class line for each delay pool.  For example, to define two
	delay pools, one of class 2 and one of class 3, the settings above
	and here would be:

Example:
 delay_pools 4      # 4 delay pools
 delay_class 1 2    # pool 1 is a class 2 pool
 delay_class 2 3    # pool 2 is a class 3 pool
 delay_class 3 4    # pool 3 is a class 4 pool
 delay_class 4 5    # pool 4 is a class 5 pool

	The delay pool classes are:

		class 1		Everything is limited by a single aggregate
				bucket.

		class 2 	Everything is limited by a single aggregate
				bucket as well as an "individual" bucket chosen
				from bits 25 through 32 of the IP address.

		class 3		Everything is limited by a single aggregate
				bucket as well as a "network" bucket chosen
				from bits 17 through 24 of the IP address and a
				"individual" bucket chosen from bits 17 through
				32 of the IP address.

		class 4		Everything in a class 3 delay pool, with an
				additional limit on a per user basis. This
				only takes effect if the username is established
				in advance - by forcing authentication in your
				http_access rules.

		class 5		Requests are grouped according their tag (see
				external_acl's tag= reply).

	NOTE: If an IP address is a.b.c.d
		-> bits 25 through 32 are "d"
		-> bits 17 through 24 are "c"
		-> bits 17 through 32 are "c * 256 + d"
DOC_END

NAME: delay_access
TYPE: delay_pool_access
DEFAULT: none
IFDEF: DELAY_POOLS
LOC: Config.Delay
DOC_START
	This is used to determine which delay pool a request falls into.

	delay_access is sorted per pool and the matching starts with pool 1,
	then pool 2, ..., and finally pool N. The first delay pool where the
	request is allowed is selected for the request. If it does not allow
	the request to any pool then the request is not delayed (default).

	For example, if you want some_big_clients in delay
	pool 1 and lotsa_little_clients in delay pool 2:

Example:
 delay_access 1 allow some_big_clients
 delay_access 1 deny all
 delay_access 2 allow lotsa_little_clients
 delay_access 2 deny all
 delay_access 3 allow authenticated_clients
DOC_END

NAME: delay_parameters
TYPE: delay_pool_rates
DEFAULT: none
IFDEF: DELAY_POOLS
LOC: Config.Delay
DOC_START
	This defines the parameters for a delay pool.  Each delay pool has
	a number of "buckets" associated with it, as explained in the
	description of delay_class.  For a class 1 delay pool, the syntax is:

delay_parameters pool aggregate

	For a class 2 delay pool:

delay_parameters pool aggregate individual

	For a class 3 delay pool:

delay_parameters pool aggregate network individual

	For a class 4 delay pool:

delay_parameters pool aggregate network individual user

	For a class 5 delay pool:

delay_parameters pool tag

	The variables here are:

		pool		a pool number - ie, a number between 1 and the
				number specified in delay_pools as used in
				delay_class lines.

		aggregate	the "delay parameters" for the aggregate bucket
				(class 1, 2, 3).

		individual	the "delay parameters" for the individual
				buckets (class 2, 3).

		network		the "delay parameters" for the network buckets
				(class 3).

		user		the delay parameters for the user buckets
				(class 4).

		tag		the delay parameters for the tag buckets
				(class 5).

	A pair of delay parameters is written restore/maximum, where restore is
	the number of bytes (not bits - modem and network speeds are usually
	quoted in bits) per second placed into the bucket, and maximum is the
	maximum number of bytes which can be in the bucket at any time.

	For example, if delay pool number 1 is a class 2 delay pool as in the
	above example, and is being used to strictly limit each host to 64kbps
	(plus overheads), with no overall limit, the line is:

delay_parameters 1 -1/-1 8000/8000

	Note that the figure -1 is used to represent "unlimited".

	And, if delay pool number 2 is a class 3 delay pool as in the above
	example, and you want to limit it to a total of 256kbps (strict limit)
	with each 8-bit network permitted 64kbps (strict limit) and each
	individual host permitted 4800bps with a bucket maximum size of 64kb
	to permit a decent web page to be downloaded at a decent speed
	(if the network is not being limited due to overuse) but slow down
	large downloads more significantly:

delay_parameters 2 32000/32000 8000/8000 600/8000

	There must be one delay_parameters line for each delay pool.

	Finally, for a class 4 delay pool as in the example - each user will
	be limited to 128Kb no matter how many workstations they are logged into.:

delay_parameters 4 32000/32000 8000/8000 600/64000 16000/16000
DOC_END

NAME: delay_initial_bucket_level
COMMENT: (percent, 0-100)
TYPE: ushort
DEFAULT: 50
IFDEF: DELAY_POOLS
LOC: Config.Delay.initial
DOC_START
	The initial bucket percentage is used to determine how much is put
	in each bucket when squid starts, is reconfigured, or first notices
	a host accessing it (in class 2 and class 3, individual hosts and
	networks only have buckets associated with them once they have been
	"seen" by squid).
DOC_END

COMMENT_START
 WCCPv1 AND WCCPv2 CONFIGURATION OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: wccp_router
TYPE: address
LOC: Config.Wccp.router
DEFAULT: 0.0.0.0
IFDEF: USE_WCCP
DOC_START
	Use this option to define your WCCP ``home'' router for
	Squid.

	wccp_router supports a single WCCP(v1) router

	wccp2_router supports multiple WCCPv2 routers

	only one of the two may be used at the same time and defines
	which version of WCCP to use.
DOC_END

NAME: wccp2_router
TYPE: IPAddress_list
LOC: Config.Wccp2.router
DEFAULT: none
IFDEF: USE_WCCPv2
DOC_START
	Use this option to define your WCCP ``home'' router for
	Squid.

	wccp_router supports a single WCCP(v1) router

	wccp2_router supports multiple WCCPv2 routers

	only one of the two may be used at the same time and defines
	which version of WCCP to use.
DOC_END

NAME: wccp_version
TYPE: int
LOC: Config.Wccp.version
DEFAULT: 4
IFDEF: USE_WCCP
DOC_START
	This directive is only relevant if you need to set up WCCP(v1)
	to some very old and end-of-life Cisco routers. In all other
	setups it must be left unset or at the default setting.
	It defines an internal version in the WCCP(v1) protocol,
	with version 4 being the officially documented protocol.

	According to some users, Cisco IOS 11.2 and earlier only
	support WCCP version 3.  If you're using that or an earlier
	version of IOS, you may need to change this value to 3, otherwise
	do not specify this parameter.
DOC_END

NAME: wccp2_rebuild_wait
TYPE: onoff
LOC: Config.Wccp2.rebuildwait
DEFAULT: on
IFDEF: USE_WCCPv2
DOC_START
	If this is enabled Squid will wait for the cache dir rebuild to finish
	before sending the first wccp2 HereIAm packet
DOC_END

NAME: wccp2_forwarding_method
TYPE: wccp2_method
LOC: Config.Wccp2.forwarding_method
DEFAULT: gre
IFDEF: USE_WCCPv2
DOC_START
	WCCP2 allows the setting of forwarding methods between the
	router/switch and the cache.  Valid values are as follows:

	gre - GRE encapsulation (forward the packet in a GRE/WCCP tunnel)
	l2  - L2 redirect (forward the packet using Layer 2/MAC rewriting)

	Currently (as of IOS 12.4) cisco routers only support GRE.
	Cisco switches only support the L2 redirect assignment method.
DOC_END

NAME: wccp2_return_method
TYPE: wccp2_method
LOC: Config.Wccp2.return_method
DEFAULT: gre
IFDEF: USE_WCCPv2
DOC_START
	WCCP2 allows the setting of return methods between the
	router/switch and the cache for packets that the cache
	decides not to handle.  Valid values are as follows:

	gre - GRE encapsulation (forward the packet in a GRE/WCCP tunnel)
	l2  - L2 redirect (forward the packet using Layer 2/MAC rewriting)

	Currently (as of IOS 12.4) cisco routers only support GRE.
	Cisco switches only support the L2 redirect assignment.

	If the "ip wccp redirect exclude in" command has been
	enabled on the cache interface, then it is still safe for
	the proxy server to use a l2 redirect method even if this
	option is set to GRE.
DOC_END

NAME: wccp2_assignment_method
TYPE: wccp2_amethod
LOC: Config.Wccp2.assignment_method
DEFAULT: hash
IFDEF: USE_WCCPv2
DOC_START
	WCCP2 allows the setting of methods to assign the WCCP hash
	Valid values are as follows:

	hash - Hash assignment
	mask  - Mask assignment

	As a general rule, cisco routers support the hash assignment method
	and cisco switches support the mask assignment method.
DOC_END

NAME: wccp2_service
TYPE: wccp2_service
LOC: Config.Wccp2.info
DEFAULT: none
DEFAULT_IF_NONE: standard 0
IFDEF: USE_WCCPv2
DOC_START
	WCCP2 allows for multiple traffic services. There are two
	types: "standard" and "dynamic". The standard type defines
	one service id - http (id 0). The dynamic service ids can be from
	51 to 255 inclusive.  In order to use a dynamic service id
	one must define the type of traffic to be redirected; this is done
	using the wccp2_service_info option.

	The "standard" type does not require a wccp2_service_info option,
	just specifying the service id will suffice.

	MD5 service authentication can be enabled by adding
	"password=<password>" to the end of this service declaration.

	Examples:

	wccp2_service standard 0	# for the 'web-cache' standard service
	wccp2_service dynamic 80	# a dynamic service type which will be
					# fleshed out with subsequent options.
	wccp2_service standard 0 password=foo
DOC_END

NAME: wccp2_service_info
TYPE: wccp2_service_info
LOC: Config.Wccp2.info
DEFAULT: none
IFDEF: USE_WCCPv2
DOC_START
	Dynamic WCCPv2 services require further information to define the
	traffic you wish to have diverted.

	The format is:

	wccp2_service_info <id> protocol=<protocol> flags=<flag>,<flag>..
	    priority=<priority> ports=<port>,<port>..

	The relevant WCCPv2 flags:
	+ src_ip_hash, dst_ip_hash
	+ source_port_hash, dst_port_hash
	+ src_ip_alt_hash, dst_ip_alt_hash
	+ src_port_alt_hash, dst_port_alt_hash
	+ ports_source

	The port list can be one to eight entries.

	Example:

	wccp2_service_info 80 protocol=tcp flags=src_ip_hash,ports_source
	    priority=240 ports=80

	Note: the service id must have been defined by a previous
	'wccp2_service dynamic <id>' entry.
DOC_END

NAME: wccp2_weight
TYPE: int
LOC: Config.Wccp2.weight
DEFAULT: 10000
IFDEF: USE_WCCPv2
DOC_START
	Each cache server gets assigned a set of the destination
	hash proportional to their weight.
DOC_END

NAME: wccp_address
TYPE: address
LOC: Config.Wccp.address
DEFAULT: 0.0.0.0
IFDEF: USE_WCCP
DOC_NONE

NAME: wccp2_address
TYPE: address
LOC: Config.Wccp2.address
DEFAULT: 0.0.0.0
IFDEF: USE_WCCPv2
DOC_START
	Use this option if you require WCCP to use a specific
	interface address.

	The default behavior is to not bind to any specific address.
DOC_END

COMMENT_START
 PERSISTENT CONNECTION HANDLING
 -----------------------------------------------------------------------------

 Also see "pconn_timeout" in the TIMEOUTS section
COMMENT_END

NAME: client_persistent_connections
TYPE: onoff
LOC: Config.onoff.client_pconns
DEFAULT: on
DOC_NONE

NAME: server_persistent_connections
TYPE: onoff
LOC: Config.onoff.server_pconns
DEFAULT: on
DOC_START
	Persistent connection support for clients and servers.  By
	default, Squid uses persistent connections (when allowed)
	with its clients and servers.  You can use these options to
	disable persistent connections with clients and/or servers.
DOC_END

NAME: persistent_connection_after_error
TYPE: onoff
LOC: Config.onoff.error_pconns
DEFAULT: off
DOC_START
	With this directive the use of persistent connections after
	HTTP errors can be disabled. Useful if you have clients
	who fail to handle errors on persistent connections proper.
DOC_END

NAME: detect_broken_pconn
TYPE: onoff
LOC: Config.onoff.detect_broken_server_pconns
DEFAULT: off
DOC_START
	Some servers have been found to incorrectly signal the use
	of HTTP/1.0 persistent connections even on replies not
	compatible, causing significant delays. This server problem
	has mostly been seen on redirects.

	By enabling this directive Squid attempts to detect such
	broken replies and automatically assume the reply is finished
	after 10 seconds timeout.
DOC_END

COMMENT_START
 CACHE DIGEST OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: digest_generation
IFDEF: USE_CACHE_DIGESTS
TYPE: onoff
LOC: Config.onoff.digest_generation
DEFAULT: on
DOC_START
	This controls whether the server will generate a Cache Digest
	of its contents.  By default, Cache Digest generation is
	enabled if Squid is compiled with --enable-cache-digests defined.
DOC_END

NAME: digest_bits_per_entry
IFDEF: USE_CACHE_DIGESTS
TYPE: int
LOC: Config.digest.bits_per_entry
DEFAULT: 5
DOC_START
	This is the number of bits of the server's Cache Digest which
	will be associated with the Digest entry for a given HTTP
	Method and URL (public key) combination.  The default is 5.
DOC_END

NAME: digest_rebuild_period
IFDEF: USE_CACHE_DIGESTS
COMMENT: (seconds)
TYPE: time_t
LOC: Config.digest.rebuild_period
DEFAULT: 1 hour
DOC_START
	This is the wait time between Cache Digest rebuilds.
DOC_END

NAME: digest_rewrite_period
COMMENT: (seconds)
IFDEF: USE_CACHE_DIGESTS
TYPE: time_t
LOC: Config.digest.rewrite_period
DEFAULT: 1 hour
DOC_START
	This is the wait time between Cache Digest writes to
	disk.
DOC_END

NAME: digest_swapout_chunk_size
COMMENT: (bytes)
TYPE: b_size_t
IFDEF: USE_CACHE_DIGESTS
LOC: Config.digest.swapout_chunk_size
DEFAULT: 4096 bytes
DOC_START
	This is the number of bytes of the Cache Digest to write to
	disk at a time.  It defaults to 4096 bytes (4KB), the Squid
	default swap page.
DOC_END

NAME: digest_rebuild_chunk_percentage
COMMENT: (percent, 0-100)
IFDEF: USE_CACHE_DIGESTS
TYPE: int
LOC: Config.digest.rebuild_chunk_percentage
DEFAULT: 10
DOC_START
	This is the percentage of the Cache Digest to be scanned at a
	time.  By default it is set to 10% of the Cache Digest.
DOC_END

COMMENT_START
 SNMP OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: snmp_port
TYPE: ushort
LOC: Config.Port.snmp
DEFAULT: 0
IFDEF: SQUID_SNMP
DOC_START
	The port number where Squid listens for SNMP requests. To enable
	SNMP support set this to a suitable port number. Port number
	3401 is often used for the Squid SNMP agent. By default it's
	set to "0" (disabled)
NOCOMMENT_START
#snmp_port 3401
NOCOMMENT_END
DOC_END

NAME: snmp_access
TYPE: acl_access
LOC: Config.accessList.snmp
DEFAULT: none
DEFAULT_IF_NONE: deny all
IFDEF: SQUID_SNMP
DOC_START
	Allowing or denying access to the SNMP port.

	All access to the agent is denied by default.
	usage:

	snmp_access allow|deny [!]aclname ...

Example:
 snmp_access allow snmppublic localhost
 snmp_access deny all
DOC_END

NAME: snmp_incoming_address
TYPE: address
LOC: Config.Addrs.snmp_incoming
DEFAULT: 0.0.0.0
IFDEF: SQUID_SNMP
DOC_NONE

NAME: snmp_outgoing_address
TYPE: address
LOC: Config.Addrs.snmp_outgoing
DEFAULT: 255.255.255.255
IFDEF: SQUID_SNMP
DOC_START
	Just like 'udp_incoming_address', but for the SNMP port.

	snmp_incoming_address	is used for the SNMP socket receiving
				messages from SNMP agents.
	snmp_outgoing_address	is used for SNMP packets returned to SNMP
				agents.

	The default snmp_incoming_address (0.0.0.0) is to listen on all
	available network interfaces.

	If snmp_outgoing_address is set to 255.255.255.255 (the default)
	it will use the same socket as snmp_incoming_address. Only
	change this if you want to have SNMP replies sent using another
	address than where this Squid listens for SNMP queries.

	NOTE, snmp_incoming_address and snmp_outgoing_address can not have
	the same value since they both use port 3401.
DOC_END

COMMENT_START
 ICP OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: icp_port udp_port
TYPE: ushort
DEFAULT: 0
LOC: Config.Port.icp
DOC_START
	The port number where Squid sends and receives ICP queries to
	and from neighbor caches.  The standard UDP port for ICP is 3130.
	Default is disabled (0).
NOCOMMENT_START
#icp_port @DEFAULT_ICP_PORT@
NOCOMMENT_END
DOC_END

NAME: htcp_port
IFDEF: USE_HTCP
TYPE: ushort
DEFAULT: 0
LOC: Config.Port.htcp
DOC_START
	The port number where Squid sends and receives HTCP queries to
	and from neighbor caches.  To turn it on you want to set it to
	4827. By default it is set to "0" (disabled).
NOCOMMENT_START
#htcp_port 4827
NOCOMMENT_END
DOC_END

NAME: log_icp_queries
COMMENT: on|off
TYPE: onoff
DEFAULT: on
LOC: Config.onoff.log_udp
DOC_START
	If set, ICP queries are logged to access.log. You may wish
	do disable this if your ICP load is VERY high to speed things
	up or to simplify log analysis.
DOC_END

NAME: udp_incoming_address
TYPE: address
LOC:Config.Addrs.udp_incoming
DEFAULT: 0.0.0.0
DOC_START
	udp_incoming_address	is used for UDP packets received from other
				caches.

	The default behavior is to not bind to any specific address.

	Only change this if you want to have all UDP queries received on
	a specific interface/address.

	NOTE: udp_incoming_address is used by the ICP, HTCP, and DNS
	modules. Altering it will affect all of them in the same manner.

	see also; udp_outgoing_address

	NOTE, udp_incoming_address and udp_outgoing_address can not
	have the same value since they both use the same port.
DOC_END

NAME: udp_outgoing_address
TYPE: address
LOC: Config.Addrs.udp_outgoing
DEFAULT: 255.255.255.255
DOC_START
	udp_outgoing_address	is used for UDP packets sent out to other
				caches.

	The default behavior is to not bind to any specific address.

	Instead it will use the same socket as udp_incoming_address.
	Only change this if you want to have UDP queries sent using another
	address than where this Squid listens for UDP queries from other
	caches.

	NOTE: udp_outgoing_address is used by the ICP, HTCP, and DNS
	modules. Altering it will affect all of them in the same manner.

	see also; udp_incoming_address

	NOTE, udp_incoming_address and udp_outgoing_address can not
	have the same value since they both use the same port.
DOC_END

NAME: icp_hit_stale
COMMENT: on|off
TYPE: onoff
DEFAULT: off
LOC: Config.onoff.icp_hit_stale
DOC_START
	If you want to return ICP_HIT for stale cache objects, set this
	option to 'on'.  If you have sibling relationships with caches
	in other administrative domains, this should be 'off'.  If you only
	have sibling relationships with caches under your control,
	it is probably okay to set this to 'on'.
	If set to 'on', your siblings should use the option "allow-miss"
	on their cache_peer lines for connecting to you.
DOC_END

NAME: minimum_direct_hops
TYPE: int
DEFAULT: 4
LOC: Config.minDirectHops
DOC_START
	If using the ICMP pinging stuff, do direct fetches for sites
	which are no more than this many hops away.
DOC_END

NAME: minimum_direct_rtt
TYPE: int
DEFAULT: 400
LOC: Config.minDirectRtt
DOC_START
	If using the ICMP pinging stuff, do direct fetches for sites
	which are no more than this many rtt milliseconds away.
DOC_END

NAME: netdb_low
TYPE: int
DEFAULT: 900
LOC: Config.Netdb.low
DOC_NONE

NAME: netdb_high
TYPE: int
DEFAULT: 1000
LOC: Config.Netdb.high
DOC_START
	The low and high water marks for the ICMP measurement
	database.  These are counts, not percents.  The defaults are
	900 and 1000.  When the high water mark is reached, database
	entries will be deleted until the low mark is reached.
DOC_END

NAME: netdb_ping_period
TYPE: time_t
LOC: Config.Netdb.period
DEFAULT: 5 minutes
DOC_START
	The minimum period for measuring a site.  There will be at
	least this much delay between successive pings to the same
	network.  The default is five minutes.
DOC_END

NAME: query_icmp
COMMENT: on|off
TYPE: onoff
DEFAULT: off
LOC: Config.onoff.query_icmp
DOC_START
	If you want to ask your peers to include ICMP data in their ICP
	replies, enable this option.

	If your peer has configured Squid (during compilation) with
	'--enable-icmp' that peer will send ICMP pings to origin server
	sites of the URLs it receives.  If you enable this option the
	ICP replies from that peer will include the ICMP data (if available).
	Then, when choosing a parent cache, Squid will choose the parent with
	the minimal RTT to the origin server.  When this happens, the
	hierarchy field of the access.log will be
	"CLOSEST_PARENT_MISS".  This option is off by default.
DOC_END

NAME: test_reachability
COMMENT: on|off
TYPE: onoff
DEFAULT: off
LOC: Config.onoff.test_reachability
DOC_START
	When this is 'on', ICP MISS replies will be ICP_MISS_NOFETCH
	instead of ICP_MISS if the target host is NOT in the ICMP
	database, or has a zero RTT.
DOC_END

NAME: icp_query_timeout
COMMENT: (msec)
DEFAULT: 0
TYPE: int
LOC: Config.Timeout.icp_query
DOC_START
	Normally Squid will automatically determine an optimal ICP
	query timeout value based on the round-trip-time of recent ICP
	queries.  If you want to override the value determined by
	Squid, set this 'icp_query_timeout' to a non-zero value.  This
	value is specified in MILLISECONDS, so, to use a 2-second
	timeout (the old default), you would write:

		icp_query_timeout 2000
DOC_END

NAME: maximum_icp_query_timeout
COMMENT: (msec)
DEFAULT: 2000
TYPE: int
LOC: Config.Timeout.icp_query_max
DOC_START
	Normally the ICP query timeout is determined dynamically.  But
	sometimes it can lead to very large values (say 5 seconds).
	Use this option to put an upper limit on the dynamic timeout
	value.  Do NOT use this option to always use a fixed (instead
	of a dynamic) timeout value. To set a fixed timeout see the
	'icp_query_timeout' directive.
DOC_END

NAME: minimum_icp_query_timeout
COMMENT: (msec)
DEFAULT: 5
TYPE: int
LOC: Config.Timeout.icp_query_min
DOC_START
	Normally the ICP query timeout is determined dynamically.  But
	sometimes it can lead to very small timeouts, even lower than
	the normal latency variance on your link due to traffic.
	Use this option to put an lower limit on the dynamic timeout
	value.  Do NOT use this option to always use a fixed (instead
	of a dynamic) timeout value. To set a fixed timeout see the
	'icp_query_timeout' directive.
DOC_END

NAME: background_ping_rate
COMMENT: time-units
TYPE: time_t
DEFAULT: 10 seconds
LOC: Config.backgroundPingRate
DOC_START
	Controls how often the ICP pings are sent to siblings that
	have background-ping set.
DOC_END

COMMENT_START
 MULTICAST ICP OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: mcast_groups
TYPE: wordlist
LOC: Config.mcast_group_list
DEFAULT: none
DOC_START
	This tag specifies a list of multicast groups which your server
	should join to receive multicasted ICP queries.

	NOTE!  Be very careful what you put here!  Be sure you
	understand the difference between an ICP _query_ and an ICP
	_reply_.  This option is to be set only if you want to RECEIVE
	multicast queries.  Do NOT set this option to SEND multicast
	ICP (use cache_peer for that).  ICP replies are always sent via
	unicast, so this option does not affect whether or not you will
	receive replies from multicast group members.

	You must be very careful to NOT use a multicast address which
	is already in use by another group of caches.

	If you are unsure about multicast, please read the Multicast
	chapter in the Squid FAQ (http://www.squid-cache.org/FAQ/).

	Usage: mcast_groups 239.128.16.128 224.0.1.20

	By default, Squid doesn't listen on any multicast groups.
DOC_END

NAME: mcast_miss_addr
IFDEF: MULTICAST_MISS_STREAM
TYPE: address
LOC: Config.mcast_miss.addr
DEFAULT: 255.255.255.255
DOC_START
	If you enable this option, every "cache miss" URL will
	be sent out on the specified multicast address.

	Do not enable this option unless you are are absolutely
	certain you understand what you are doing.
DOC_END

NAME: mcast_miss_ttl
IFDEF: MULTICAST_MISS_STREAM
TYPE: ushort
LOC: Config.mcast_miss.ttl
DEFAULT: 16
DOC_START
	This is the time-to-live value for packets multicasted
	when multicasting off cache miss URLs is enabled.  By
	default this is set to 'site scope', i.e. 16.
DOC_END

NAME: mcast_miss_port
IFDEF: MULTICAST_MISS_STREAM
TYPE: ushort
LOC: Config.mcast_miss.port
DEFAULT: 3135
DOC_START
	This is the port number to be used in conjunction with
	'mcast_miss_addr'.
DOC_END

NAME: mcast_miss_encode_key
IFDEF: MULTICAST_MISS_STREAM
TYPE: string
LOC: Config.mcast_miss.encode_key
DEFAULT: XXXXXXXXXXXXXXXX
DOC_START
	The URLs that are sent in the multicast miss stream are
	encrypted.  This is the encryption key.
DOC_END

NAME: mcast_icp_query_timeout
COMMENT: (msec)
DEFAULT: 2000
TYPE: int
LOC: Config.Timeout.mcast_icp_query
DOC_START
	For multicast peers, Squid regularly sends out ICP "probes" to
	count how many other peers are listening on the given multicast
	address.  This value specifies how long Squid should wait to
	count all the replies.  The default is 2000 msec, or 2
	seconds.
DOC_END

COMMENT_START
 INTERNAL ICON OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: icon_directory
TYPE: string
LOC: Config.icons.directory
DEFAULT: @DEFAULT_ICON_DIR@
DOC_START
	Where the icons are stored. These are normally kept in
	@DEFAULT_ICON_DIR@
DOC_END

NAME: global_internal_static
TYPE: onoff
LOC: Config.onoff.global_internal_static
DEFAULT: on
DOC_START
	This directive controls is Squid should intercept all requests for
	/squid-internal-static/ no matter which host the URL is requesting
	(default on setting), or if nothing special should be done for
	such URLs (off setting). The purpose of this directive is to make
	icons etc work better in complex cache hierarchies where it may
	not always be possible for all corners in the cache mesh to reach
	the server generating a directory listing.
DOC_END

NAME: short_icon_urls
TYPE: onoff
LOC: Config.icons.use_short_names
DEFAULT: on
DOC_START
	If this is enabled Squid will use short URLs for icons.
	If disabled it will revert to the old behavior of including
	it's own name and port in the URL.

	If you run a complex cache hierarchy with a mix of Squid and
	other proxies you may need to disable this directive.
DOC_END

COMMENT_START
 ERROR PAGE OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: error_directory
TYPE: string
LOC: Config.errorDirectory
DEFAULT: none
DOC_START
	If you wish to create your own versions of the default
	error files to customize them to suit your company copy
	the error/template files to another directory and point
	this tag at them.

	WARNING: This option will disable multi-language support
	         on error pages if used.

	The squid developers are interested in making squid available in
	a wide variety of languages. If you are making translations for a
	language that Squid does not currently provide please consider
	contributing your translation back to the project.
	http://wiki.squid-cache.org/Translations

	The squid developers working on translations are happy to supply drop-in
	translated error files in exchange for any new language contributions.
DOC_END

NAME: error_default_language
IFDEF: USE_ERR_LOCALES
TYPE: string
LOC: Config.errorDefaultLanguage
DEFAULT: none
DOC_START
	Set the default language which squid will send error pages in
	if no existing translation matches the clients language
	preferences.

	If unset (default) generic English will be used.

	The squid developers are interested in making squid available in
	a wide variety of languages. If you are interested in making
	translations for any language see the squid wiki for details.
	http://wiki.squid-cache.org/Translations
DOC_END

NAME: error_log_languages
IFDEF: USE_ERR_LOCALES
TYPE: onoff
LOC: Config.errorLogMissingLanguages
DEFAULT: on
DOC_START
	Log to cache.log what languages users are attempting to
	auto-negotiate for translations.

	Successful negotiations are not logged. Only failures
	have meaning to indicate that Squid may need an upgrade
	of its error page translations.
DOC_END

NAME: err_page_stylesheet
TYPE: string
LOC: Config.errorStylesheet
DEFAULT: @DEFAULT_CONFIG_DIR@/errorpage.css
DOC_START
	CSS Stylesheet to pattern the display of Squid default error pages.

	For information on CSS see http://www.w3.org/Style/CSS/
DOC_END

NAME: err_html_text
TYPE: eol
LOC: Config.errHtmlText
DEFAULT: none
DOC_START
	HTML text to include in error messages.  Make this a "mailto"
	URL to your admin address, or maybe just a link to your
	organizations Web page.

	To include this in your error messages, you must rewrite
	the error template files (found in the "errors" directory).
	Wherever you want the 'err_html_text' line to appear,
	insert a %L tag in the error template file.
DOC_END

NAME: email_err_data
COMMENT: on|off
TYPE: onoff
LOC: Config.onoff.emailErrData
DEFAULT: on
DOC_START
	If enabled, information about the occurred error will be
	included in the mailto links of the ERR pages (if %W is set)
	so that the email body contains the data.
	Syntax is <A HREF="mailto:%w%W">%w</A>
DOC_END

NAME: deny_info
TYPE: denyinfo
LOC: Config.denyInfoList
DEFAULT: none
DOC_START
	Usage:   deny_info err_page_name acl
	or       deny_info http://... acl
	or       deny_info TCP_RESET acl

	This can be used to return a ERR_ page for requests which
	do not pass the 'http_access' rules.  Squid remembers the last
	acl it evaluated in http_access, and if a 'deny_info' line exists
	for that ACL Squid returns a corresponding error page.

	The acl is typically the last acl on the http_access deny line which
	denied access. The exceptions to this rule are:
	- When Squid needs to request authentication credentials. It's then
	  the first authentication related acl encountered
	- When none of the http_access lines matches. It's then the last
	  acl processed on the last http_access line.

	NP: If providing your own custom error pages with error_directory
	    you may also specify them by your custom file name:
	    Example: deny_info ERR_CUSTOM_ACCESS_DENIED bad_guys

	Alternatively you can specify an error URL. The browsers will
	get redirected (302) to the specified URL. %s in the redirection
	URL will be replaced by the requested URL.

	Alternatively you can tell Squid to reset the TCP connection
	by specifying TCP_RESET.
DOC_END

COMMENT_START
 OPTIONS INFLUENCING REQUEST FORWARDING 
 -----------------------------------------------------------------------------
COMMENT_END

NAME: nonhierarchical_direct
TYPE: onoff
LOC: Config.onoff.nonhierarchical_direct
DEFAULT: on
DOC_START
	By default, Squid will send any non-hierarchical requests
	(matching hierarchy_stoplist or not cacheable request type) direct
	to origin servers.

	If you set this to off, Squid will prefer to send these
	requests to parents.

	Note that in most configurations, by turning this off you will only
	add latency to these request without any improvement in global hit
	ratio.

	If you are inside an firewall see never_direct instead of
	this directive.
DOC_END

NAME: prefer_direct
TYPE: onoff
LOC: Config.onoff.prefer_direct
DEFAULT: off
DOC_START
	Normally Squid tries to use parents for most requests. If you for some
	reason like it to first try going direct and only use a parent if
	going direct fails set this to on.

	By combining nonhierarchical_direct off and prefer_direct on you
	can set up Squid to use a parent as a backup path if going direct
	fails.

	Note: If you want Squid to use parents for all requests see
	the never_direct directive. prefer_direct only modifies how Squid
	acts on cacheable requests.
DOC_END

NAME: always_direct
TYPE: acl_access
LOC: Config.accessList.AlwaysDirect
DEFAULT: none
DOC_START
	Usage: always_direct allow|deny [!]aclname ...

	Here you can use ACL elements to specify requests which should
	ALWAYS be forwarded by Squid to the origin servers without using
	any peers.  For example, to always directly forward requests for
	local servers ignoring any parents or siblings you may have use
	something like:

		acl local-servers dstdomain my.domain.net
		always_direct allow local-servers

	To always forward FTP requests directly, use

		acl FTP proto FTP
		always_direct allow FTP

	NOTE: There is a similar, but opposite option named
	'never_direct'.  You need to be aware that "always_direct deny
	foo" is NOT the same thing as "never_direct allow foo".  You
	may need to use a deny rule to exclude a more-specific case of
	some other rule.  Example:

		acl local-external dstdomain external.foo.net
		acl local-servers dstdomain  .foo.net
		always_direct deny local-external
		always_direct allow local-servers

	NOTE: If your goal is to make the client forward the request
	directly to the origin server bypassing Squid then this needs
	to be done in the client configuration. Squid configuration
	can only tell Squid how Squid should fetch the object.

	NOTE: This directive is not related to caching. The replies
	is cached as usual even if you use always_direct. To not cache
	the replies see no_cache.

	This option replaces some v1.1 options such as local_domain
	and local_ip.
DOC_END

NAME: never_direct
TYPE: acl_access
LOC: Config.accessList.NeverDirect
DEFAULT: none
DOC_START
	Usage: never_direct allow|deny [!]aclname ...

	never_direct is the opposite of always_direct.  Please read
	the description for always_direct if you have not already.

	With 'never_direct' you can use ACL elements to specify
	requests which should NEVER be forwarded directly to origin
	servers.  For example, to force the use of a proxy for all
	requests, except those in your local domain use something like:

		acl local-servers dstdomain .foo.net
		never_direct deny local-servers
		never_direct allow all

	or if Squid is inside a firewall and there are local intranet
	servers inside the firewall use something like:

		acl local-intranet dstdomain .foo.net
		acl local-external dstdomain external.foo.net
		always_direct deny local-external
		always_direct allow local-intranet
		never_direct allow all

	This option replaces some v1.1 options such as inside_firewall
	and firewall_ip.
DOC_END

COMMENT_START
 ADVANCED NETWORKING OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: incoming_icp_average
TYPE: int
DEFAULT: 6
LOC: Config.comm_incoming.icp_average
DOC_NONE

NAME: incoming_http_average
TYPE: int
DEFAULT: 4
LOC: Config.comm_incoming.http_average
DOC_NONE

NAME: incoming_dns_average
TYPE: int
DEFAULT: 4
LOC: Config.comm_incoming.dns_average
DOC_NONE

NAME: min_icp_poll_cnt
TYPE: int
DEFAULT: 8
LOC: Config.comm_incoming.icp_min_poll
DOC_NONE

NAME: min_dns_poll_cnt
TYPE: int
DEFAULT: 8
LOC: Config.comm_incoming.dns_min_poll
DOC_NONE

NAME: min_http_poll_cnt
TYPE: int
DEFAULT: 8
LOC: Config.comm_incoming.http_min_poll
DOC_START
	Heavy voodoo here.  I can't even believe you are reading this.
	Are you crazy?  Don't even think about adjusting these unless
	you understand the algorithms in comm_select.c first!
DOC_END

NAME: accept_filter
TYPE: string
DEFAULT: none
LOC: Config.accept_filter
DOC_START
	FreeBSD:

	The name of an accept(2) filter to install on Squid's
	listen socket(s).  This feature is perhaps specific to
	FreeBSD and requires support in the kernel.

	The 'httpready' filter delays delivering new connections
	to Squid until a full HTTP request has been received.
	See the accf_http(9) man page for details.

	The 'dataready' filter delays delivering new connections
	to Squid until there is some data to process.
	See the accf_dataready(9) man page for details.

	Linux:
	
	The 'data' filter delays delivering of new connections
	to Squid until there is some data to process by TCP_ACCEPT_DEFER.
	You may optionally specify a number of seconds to wait by
	'data=N' where N is the number of seconds. Defaults to 30
	if not specified.  See the tcp(7) man page for details.
EXAMPLE:
# FreeBSD
accept_filter httpready
# Linux
accept_filter data
DOC_END

NAME: tcp_recv_bufsize
COMMENT: (bytes)
TYPE: b_size_t
DEFAULT: 0 bytes
LOC: Config.tcpRcvBufsz
DOC_START
	Size of receive buffer to set for TCP sockets.  Probably just
	as easy to change your kernel's default.  Set to zero to use
	the default buffer size.
DOC_END

COMMENT_START
 ICAP OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: icap_enable
TYPE: onoff
IFDEF: ICAP_CLIENT
COMMENT: on|off
LOC: TheICAPConfig.onoff
DEFAULT: off
DOC_START
	If you want to enable the ICAP module support, set this to on.
DOC_END

NAME: icap_connect_timeout
TYPE: time_t
DEFAULT: none
LOC: TheICAPConfig.connect_timeout_raw
IFDEF: ICAP_CLIENT
DOC_START
	This parameter specifies how long to wait for the TCP connect to
	the requested ICAP server to complete before giving up and either
	terminating the HTTP transaction or bypassing the failure.

	The default for optional services is peer_connect_timeout.
	The default for essential services is connect_timeout.
	If this option is explicitly set, its value applies to all services.
DOC_END

NAME: icap_io_timeout
COMMENT: time-units
TYPE: time_t
DEFAULT: none
LOC: TheICAPConfig.io_timeout_raw
IFDEF: ICAP_CLIENT
DOC_START
	This parameter specifies how long to wait for an I/O activity on
	an established, active ICAP connection before giving up and
	either terminating the HTTP transaction or bypassing the
	failure.

	The default is read_timeout.
DOC_END

NAME: icap_service_failure_limit
TYPE: int
IFDEF: ICAP_CLIENT
LOC: TheICAPConfig.service_failure_limit
DEFAULT: 10
DOC_START
	The limit specifies the number of failures that Squid tolerates
	when establishing a new TCP connection with an ICAP service. If
	the number of failures exceeds the limit, the ICAP service is
	not used for new ICAP requests until it is time to refresh its
	OPTIONS. The per-service failure counter is reset to zero each
	time Squid fetches new service OPTIONS.

	A negative value disables the limit. Without the limit, an ICAP
	service will not be considered down due to connectivity failures
	between ICAP OPTIONS requests.
DOC_END

NAME: icap_service_revival_delay
TYPE: int
IFDEF: ICAP_CLIENT
LOC: TheICAPConfig.service_revival_delay
DEFAULT: 180
DOC_START
	The delay specifies the number of seconds to wait after an ICAP
	OPTIONS request failure before requesting the options again. The
	failed ICAP service is considered "down" until fresh OPTIONS are
	fetched.

	The actual delay cannot be smaller than the hardcoded minimum
	delay of 30 seconds.
DOC_END

NAME: icap_preview_enable
TYPE: onoff
IFDEF: ICAP_CLIENT
COMMENT: on|off
LOC: TheICAPConfig.preview_enable
DEFAULT: on
DOC_START
	The ICAP Preview feature allows the ICAP server to handle the
	HTTP message by looking only at the beginning of the message body
	or even without receiving the body at all. In some environments, 
	previews greatly speedup ICAP processing.

	During an ICAP OPTIONS transaction, the server may tell	Squid what
	HTTP messages should be previewed and how big the preview should be.
	Squid will not use Preview if the server did not request one.

	To disable ICAP Preview for all ICAP services, regardless of
	individual ICAP server OPTIONS responses, set this option to "off".
Example:
icap_preview_enable off
DOC_END

NAME: icap_preview_size
TYPE: int
IFDEF: ICAP_CLIENT
LOC: TheICAPConfig.preview_size
DEFAULT: -1
DOC_START
	The default size of preview data to be sent to the ICAP server.
	-1 means no preview. This value might be overwritten on a per server
	basis by OPTIONS requests.
DOC_END

NAME: icap_default_options_ttl
TYPE: int
IFDEF: ICAP_CLIENT
LOC: TheICAPConfig.default_options_ttl
DEFAULT: 60
DOC_START
	The default TTL value for ICAP OPTIONS responses that don't have
	an Options-TTL header.
DOC_END

NAME: icap_persistent_connections
TYPE: onoff
IFDEF: ICAP_CLIENT
COMMENT: on|off
LOC: TheICAPConfig.reuse_connections
DEFAULT: on
DOC_START
	Whether or not Squid should use persistent connections to
	an ICAP server.
DOC_END

NAME: icap_send_client_ip
TYPE: onoff
IFDEF: ICAP_CLIENT
COMMENT: on|off
LOC: TheICAPConfig.send_client_ip
DEFAULT: off
DOC_START
	This adds the header "X-Client-IP" to ICAP requests.
DOC_END

NAME: icap_send_client_username
TYPE: onoff
IFDEF: ICAP_CLIENT
COMMENT: on|off
LOC: TheICAPConfig.send_client_username
DEFAULT: off
DOC_START
	This sends authenticated HTTP client username (if available) to
	the ICAP service. The username value is encoded based on the
	icap_client_username_encode option and is sent using the header
	specified by the icap_client_username_header option.
DOC_END

NAME: icap_client_username_header
TYPE: string
IFDEF: ICAP_CLIENT
LOC: TheICAPConfig.client_username_header
DEFAULT: X-Client-Username
DOC_START
	ICAP request header name to use for send_client_username.
DOC_END

NAME: icap_client_username_encode
TYPE: onoff
IFDEF: ICAP_CLIENT
COMMENT: on|off
LOC: TheICAPConfig.client_username_encode
DEFAULT: off
DOC_START
	Whether to base64 encode the authenticated client username.
DOC_END

NAME: icap_service
TYPE: icap_service_type
IFDEF: ICAP_CLIENT
LOC: TheICAPConfig
DEFAULT: none
DOC_START
	Defines a single ICAP service

	icap_service servicename vectoring_point bypass service_url

	vectoring_point = reqmod_precache|reqmod_postcache|respmod_precache|respmod_postcache
		This specifies at which point of transaction processing the
		ICAP service should be activated. *_postcache vectoring points
		are not yet supported.
	bypass = 1|0
		If set to 1, the ICAP service is treated as optional. If the
		service cannot be reached or malfunctions, Squid will try to
		ignore any errors and process the message as if the service
		was not enabled. No all ICAP errors can be bypassed.
		If set to 0, the ICAP service is treated as essential and all
		ICAP errors will result in an error page returned to the
		HTTP client.
	service_url = icap://servername:port/service

Example:
icap_service service_1 reqmod_precache 0 icap://icap1.mydomain.net:1344/reqmod
icap_service service_2 respmod_precache 0 icap://icap2.mydomain.net:1344/respmod
DOC_END

NAME: icap_class
TYPE: icap_class_type
IFDEF: ICAP_CLIENT
LOC: none
DEFAULT: none
DOC_START
	This depricated option was documented to define an ICAP service
	chain, even though it actually defined a set of similar, redundant
	services, and the chains were not supported. 

	To define a set of redundant services, please use the
	adaptation_service_set directive.

	If you need adaptation service chains, patches or sponsorship
	is welcome.
DOC_END

NAME: icap_access
TYPE: icap_access_type
IFDEF: ICAP_CLIENT
LOC: none
DEFAULT: none
DOC_START
        This option is depricated. Please use adaptation_access, which
	has the same ICAP functionality, but comes with better
	documentation, and eCAP support.
DOC_END

COMMENT_START
 eCAP OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: ecap_enable
TYPE: onoff
IFDEF: USE_ECAP
COMMENT: on|off
LOC: Ecap::TheConfig.onoff
DEFAULT: off
DOC_START
	Controls whether eCAP support is enabled.
DOC_END

NAME: ecap_service
TYPE: ecap_service_type
IFDEF: USE_ECAP
LOC: Ecap::TheConfig
DEFAULT: none
DOC_START
	Defines a single eCAP service

	ecap_service servicename vectoring_point bypass service_url

	vectoring_point = reqmod_precache|reqmod_postcache|respmod_precache|respmod_postcache
		This specifies at which point of transaction processing the
		eCAP service should be activated. *_postcache vectoring points
		are not yet supported.
	bypass = 1|0
		If set to 1, the eCAP service is treated as optional. If the
		service cannot be reached or malfunctions, Squid will try to
		ignore any errors and process the message as if the service
		was not enabled. No all eCAP errors can be bypassed.
		If set to 0, the eCAP service is treated as essential and all
		eCAP errors will result in an error page returned to the
		HTTP client.
	service_url = ecap://vendor/service_name?custom&cgi=style&parameters=optional

Example:
ecap_service service_1 reqmod_precache 0 ecap://filters-R-us/leakDetector?on_error=block
ecap_service service_2 respmod_precache 1 icap://filters-R-us/virusFilter?config=/etc/vf.cfg
DOC_END

NAME: loadable_modules
TYPE: wordlist
IFDEF: USE_LOADABLE_MODULES
LOC: Config.loadable_module_names
DEFAULT: none
DOC_START
	Instructs Squid to load the specified dynamic module(s) or activate
	preloaded module(s).
Example:
loadable_modules @DEFAULT_PREFIX@/lib/MinimalAdapter.so
DOC_END

COMMENT_START
 MESSAGE ADAPTATION OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: adaptation_service_set
TYPE: adaptation_service_set_type
IFDEF: USE_ADAPTATION
LOC: none
DEFAULT: none
DOC_START

	Defines a named adaptation service set. The set is populated in
	the order of adaptation_service_set directives in this file.
	When adaptation ACLs are processed, the first and only the first
	applicable adaptation service from the set will be used. Thus,
	the set should group similar, redundant services, rather than a
	chain of complementary services.

	If you have a single adaptation service, you do not need to
	define a set containing it because adaptation_access accepts
	service names.

	See also: adaptation_access

Example:
adaptation_service_set svcBlocker urlFilterPrimary urlFilterBackup
adaptation service_set svcLogger loggerLocal loggerRemote
DOC_END

NAME: adaptation_access
TYPE: adaptation_access_type
IFDEF: USE_ADAPTATION
LOC: none
DEFAULT: none
DOC_START
	Sends an HTTP transaction to an ICAP or eCAP adaptation	service.

	adaptation_access service_name allow|deny [!]aclname...
	adaptation_access set_name     allow|deny [!]aclname...

	At each supported vectoring point, the adaptation_access
	statements are processed in the order they appear in this
	configuration file. Statements pointing to the following services
	are ignored (i.e., skipped without checking their ACL):

	    - services serving different vectoring points
	    - "broken-but-bypassable" services
	    - "up" services configured to ignore such transactions
              (e.g., based on the ICAP Transfer-Ignore header).

        When a set_name is used, all services in the set are checked
	using the same rules, to find the first applicable one. See
	adaptation_service_set for details.

	If an access list is checked and there is a match, the
	processing stops: For an "allow" rule, the corresponding
	adaptation service is used for the transaction. For a "deny"
	rule, no adaptation service is activated.

	It is currently not possible to apply more than one adaptation
	service at the same vectoring point to the same HTTP transaction.

        See also: icap_service and ecap_service

Example:
adaptation_access service_1 allow all
DOC_END

COMMENT_START
 DNS OPTIONS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: check_hostnames
TYPE: onoff
DEFAULT: off
LOC: Config.onoff.check_hostnames
DOC_START
	For security and stability reasons Squid can check
	hostnames for Internet standard RFC compliance. If you want
	Squid to perform these checks turn this directive on.
DOC_END

NAME: allow_underscore
TYPE: onoff
DEFAULT: on
LOC: Config.onoff.allow_underscore
DOC_START
	Underscore characters is not strictly allowed in Internet hostnames
	but nevertheless used by many sites. Set this to off if you want
	Squid to be strict about the standard.
	This check is performed only when check_hostnames is set to on.
DOC_END

NAME: cache_dns_program
TYPE: string
IFDEF: USE_DNSSERVERS
DEFAULT: @DEFAULT_DNSSERVER@
LOC: Config.Program.dnsserver
DOC_START
	Specify the location of the executable for dnslookup process.
DOC_END

NAME: dns_children
TYPE: int
IFDEF: USE_DNSSERVERS
DEFAULT: 5
LOC: Config.dnsChildren
DOC_START
	The number of processes spawn to service DNS name lookups.
	For heavily loaded caches on large servers, you should
	probably increase this value to at least 10.  The maximum
	is 32.  The default is 5.

	You must have at least one dnsserver process.
DOC_END

NAME: dns_retransmit_interval
TYPE: time_t
DEFAULT: 5 seconds
LOC: Config.Timeout.idns_retransmit
IFDEF: !USE_DNSSERVERS
DOC_START
	Initial retransmit interval for DNS queries. The interval is
	doubled each time all configured DNS servers have been tried.

DOC_END

NAME: dns_timeout
TYPE: time_t
DEFAULT: 2 minutes
LOC: Config.Timeout.idns_query
IFDEF: !USE_DNSSERVERS
DOC_START
	DNS Query timeout. If no response is received to a DNS query
	within this time all DNS servers for the queried domain
	are assumed to be unavailable.
DOC_END

NAME: dns_defnames
COMMENT: on|off
TYPE: onoff
DEFAULT: off
LOC: Config.onoff.res_defnames
DOC_START
	Normally the RES_DEFNAMES resolver option is disabled
	(see res_init(3)).  This prevents caches in a hierarchy
	from interpreting single-component hostnames locally.  To allow
	Squid to handle single-component names, enable this option.
DOC_END

NAME: dns_nameservers
TYPE: wordlist
DEFAULT: none
LOC: Config.dns_nameservers
DOC_START
	Use this if you want to specify a list of DNS name servers
	(IP addresses) to use instead of those given in your
	/etc/resolv.conf file.
	On Windows platforms, if no value is specified here or in
	the /etc/resolv.conf file, the list of DNS name servers are
	taken from the Windows registry, both static and dynamic DHCP
	configurations are supported.

	Example: dns_nameservers 10.0.0.1 192.172.0.4
DOC_END

NAME: hosts_file
TYPE: string
DEFAULT: @DEFAULT_HOSTS@
LOC: Config.etcHostsPath
DOC_START
	Location of the host-local IP name-address associations
	database. Most Operating Systems have such a file on different
	default locations:
	- Un*X & Linux:    /etc/hosts
	- Windows NT/2000: %SystemRoot%\system32\drivers\etc\hosts
			   (%SystemRoot% value install default is c:\winnt)
	- Windows XP/2003: %SystemRoot%\system32\drivers\etc\hosts
			   (%SystemRoot% value install default is c:\windows)
	- Windows 9x/Me:   %windir%\hosts
			   (%windir% value is usually c:\windows)
	- Cygwin:	   /etc/hosts

	The file contains newline-separated definitions, in the
	form ip_address_in_dotted_form name [name ...] names are
	whitespace-separated. Lines beginning with an hash (#)
	character are comments.

	The file is checked at startup and upon configuration.
	If set to 'none', it won't be checked.
	If append_domain is used, that domain will be added to
	domain-local (i.e. not containing any dot character) host
	definitions.
DOC_END

NAME: append_domain
TYPE: string
LOC:  Config.appendDomain
DEFAULT: none
DOC_START
	Appends local domain name to hostnames without any dots in
	them.  append_domain must begin with a period.

	Be warned there are now Internet names with no dots in
	them using only top-domain names, so setting this may
	cause some Internet sites to become unavailable.

Example:
 append_domain .yourdomain.com
DOC_END

NAME: ignore_unknown_nameservers
TYPE: onoff
LOC: Config.onoff.ignore_unknown_nameservers
DEFAULT: on
DOC_START
	By default Squid checks that DNS responses are received
	from the same IP addresses they are sent to.  If they
	don't match, Squid ignores the response and writes a warning
	message to cache.log.  You can allow responses from unknown
	nameservers by setting this option to 'off'.
DOC_END

NAME: dns_v4_fallback
TYPE: onoff
DEFAULT: on
LOC: Config.onoff.dns_require_A
DOC_START
	Standard practice with DNS is to lookup either A or AAAA records
	and use the results if it succeeds. Only looking up the other if
	the first attempt fails or otherwise produces no results.

	That policy however will cause squid to produce error pages for some
	servers that advertise AAAA but are unreachable over IPv6.

	If this is ON  squid will always lookup both AAAA and A, using both.
	If this is OFF squid will lookup AAAA and only try A if none found.

	WARNING: There are some possibly unwanted side-effects with this on:
		*) Doubles the load placed by squid on the DNS network.
		*) May negatively impact connection delay times.
DOC_END

NAME: ipcache_size
COMMENT: (number of entries)
TYPE: int
DEFAULT: 1024
LOC: Config.ipcache.size
DOC_NONE

NAME: ipcache_low
COMMENT: (percent)
TYPE: int
DEFAULT: 90
LOC: Config.ipcache.low
DOC_NONE

NAME: ipcache_high
COMMENT: (percent)
TYPE: int
DEFAULT: 95
LOC: Config.ipcache.high
DOC_START
	The size, low-, and high-water marks for the IP cache.
DOC_END

NAME: fqdncache_size
COMMENT: (number of entries)
TYPE: int
DEFAULT: 1024
LOC: Config.fqdncache.size
DOC_START
	Maximum number of FQDN cache entries.
DOC_END

COMMENT_START
 MISCELLANEOUS
 -----------------------------------------------------------------------------
COMMENT_END

NAME: memory_pools
COMMENT: on|off
TYPE: onoff
DEFAULT: on
LOC: Config.onoff.mem_pools
DOC_START
	If set, Squid will keep pools of allocated (but unused) memory
	available for future use.  If memory is a premium on your
	system and you believe your malloc library outperforms Squid
	routines, disable this.
DOC_END

NAME: memory_pools_limit
COMMENT: (bytes)
TYPE: b_size_t
DEFAULT: 5 MB
LOC: Config.MemPools.limit
DOC_START
	Used only with memory_pools on:
	memory_pools_limit 50 MB

	If set to a non-zero value, Squid will keep at most the specified
	limit of allocated (but unused) memory in memory pools. All free()
	requests that exceed this limit will be handled by your malloc
	library. Squid does not pre-allocate any memory, just safe-keeps
	objects that otherwise would be free()d. Thus, it is safe to set
	memory_pools_limit to a reasonably high value even if your
	configuration will use less memory.

	If set to zero, Squid will keep all memory it can. That is, there
	will be no limit on the total amount of memory used for safe-keeping.

	To disable memory allocation optimization, do not set
	memory_pools_limit to 0. Set memory_pools to "off" instead.

	An overhead for maintaining memory pools is not taken into account
	when the limit is checked. This overhead is close to four bytes per
	object kept. However, pools may actually _save_ memory because of
	reduced memory thrashing in your malloc library.
DOC_END

NAME: forwarded_for
COMMENT: on|off|transparent|truncate|delete
TYPE: string
DEFAULT: on
LOC: opt_forwarded_for
DOC_START
	If set to "on", Squid will append your client's IP address
	in the HTTP requests it forwards. By default it looks like:

		X-Forwarded-For: 192.1.2.3

	If set to "off", it will appear as

		X-Forwarded-For: unknown

	If set to "transparent", Squid will not alter the
	X-Forwarded-For header in any way.

	If set to "delete", Squid will delete the entire
	X-Forwarded-For header.

	If set to "truncate", Squid will remove all existing
	X-Forwarded-For entries, and place itself as the sole entry.
DOC_END

NAME: cachemgr_passwd
TYPE: cachemgrpasswd
DEFAULT: none
LOC: Config.passwd_list
DOC_START
	Specify passwords for cachemgr operations.

	Usage: cachemgr_passwd password action action ...

	Some valid actions are (see cache manager menu for a full list):
		5min
		60min
		asndb
		authenticator
		cbdata
		client_list
		comm_incoming
		config *
		counters
		delay
		digest_stats
		dns
		events
		filedescriptors
		fqdncache
		histograms
		http_headers
		info
		io
		ipcache
		mem
		menu
		netdb
		non_peers
		objects
		offline_toggle *
		pconn
		peer_select
		reconfigure *
		redirector
		refresh
		server_list
		shutdown *
		store_digest
		storedir
		utilization
		via_headers
		vm_objects

	* Indicates actions which will not be performed without a
	  valid password, others can be performed if not listed here.

	To disable an action, set the password to "disable".
	To allow performing an action without a password, set the
	password to "none".

	Use the keyword "all" to set the same password for all actions.

Example:
 cachemgr_passwd secret shutdown
 cachemgr_passwd lesssssssecret info stats/objects
 cachemgr_passwd disable all
DOC_END

NAME: client_db
COMMENT: on|off
TYPE: onoff
DEFAULT: on
LOC: Config.onoff.client_db
DOC_START
	If you want to disable collecting per-client statistics,
	turn off client_db here.
DOC_END

NAME: refresh_all_ims
COMMENT: on|off
TYPE: onoff
DEFAULT: off
LOC: Config.onoff.refresh_all_ims
DOC_START
	When you enable this option, squid will always check
	the origin server for an update when a client sends an
	If-Modified-Since request.  Many browsers use IMS
	requests when the user requests a reload, and this
	ensures those clients receive the latest version.

	By default (off), squid may return a Not Modified response
	based on the age of the cached version.
DOC_END

NAME: reload_into_ims
IFDEF: HTTP_VIOLATIONS
COMMENT: on|off
TYPE: onoff
DEFAULT: off
LOC: Config.onoff.reload_into_ims
DOC_START
	When you enable this option, client no-cache or ``reload''
	requests will be changed to If-Modified-Since requests.
	Doing this VIOLATES the HTTP standard.  Enabling this
	feature could make you liable for problems which it
	causes.

	see also refresh_pattern for a more selective approach.
DOC_END

NAME: maximum_single_addr_tries
TYPE: int
LOC: Config.retry.maxtries
DEFAULT: 1
DOC_START
	This sets the maximum number of connection attempts for a
	host that only has one address (for multiple-address hosts,
	each address is tried once).

	The default value is one attempt, the (not recommended)
	maximum is 255 tries.  A warning message will be generated
	if it is set to a value greater than ten.

	Note: This is in addition to the request re-forwarding which
	takes place if Squid fails to get a satisfying response.
DOC_END

NAME: retry_on_error
TYPE: onoff
LOC: Config.retry.onerror
DEFAULT: off
DOC_START
	If set to on Squid will automatically retry requests when
	receiving an error response. This is mainly useful if you
	are in a complex cache hierarchy to work around access
	control errors.
DOC_END

NAME: as_whois_server
TYPE: string
LOC: Config.as_whois_server
DEFAULT: whois.ra.net
DEFAULT_IF_NONE: whois.ra.net
DOC_START
	WHOIS server to query for AS numbers.  NOTE: AS numbers are
	queried only when Squid starts up, not for every request.
DOC_END

NAME: offline_mode
TYPE: onoff
LOC: Config.onoff.offline
DEFAULT: off
DOC_START
	Enable this option and Squid will never try to validate cached
	objects.
DOC_END

NAME: uri_whitespace
TYPE: uri_whitespace
LOC: Config.uri_whitespace
DEFAULT: strip
DOC_START
	What to do with requests that have whitespace characters in the
	URI.  Options:

	strip:  The whitespace characters are stripped out of the URL.
		This is the behavior recommended by RFC2396.
	deny:   The request is denied.  The user receives an "Invalid
		Request" message.
	allow:  The request is allowed and the URI is not changed.  The
		whitespace characters remain in the URI.  Note the
		whitespace is passed to redirector processes if they
		are in use.
	encode:	The request is allowed and the whitespace characters are
		encoded according to RFC1738.  This could be considered
		a violation of the HTTP/1.1
		RFC because proxies are not allowed to rewrite URI's.
	chop:	The request is allowed and the URI is chopped at the
		first whitespace.  This might also be considered a
		violation.
DOC_END

NAME: coredump_dir
TYPE: string
LOC: Config.coredump_dir
DEFAULT: none
DEFAULT_IF_NONE: none
DOC_START
	By default Squid leaves core files in the directory from where
	it was started. If you set 'coredump_dir' to a directory
	that exists, Squid will chdir() to that directory at startup
	and coredump files will be left there.

NOCOMMENT_START
# Leave coredumps in the first cache dir
coredump_dir @DEFAULT_SWAP_DIR@
NOCOMMENT_END
DOC_END

NAME: chroot
TYPE: string
LOC: Config.chroot_dir
DEFAULT: none
DOC_START
	Use this to have Squid do a chroot() while initializing.  This
	also causes Squid to fully drop root privileges after
	initializing.  This means, for example, if you use a HTTP
	port less than 1024 and try to reconfigure, you will may get an
	error saying that Squid can not open the port.
DOC_END

NAME: balance_on_multiple_ip
TYPE: onoff
LOC: Config.onoff.balance_on_multiple_ip
DEFAULT: off
DOC_START
	Modern IP resolvers in squid sort lookup results by preferred access.
	By default squid will use these IP in order and only rotates to
	the next listed when the most preffered fails.

	Some load balancing servers based on round robin DNS have been
	found not to preserve user session state across requests
	to different IP addresses.

	Enabling this directive Squid rotates IP's per request.
DOC_END

NAME: pipeline_prefetch
TYPE: onoff
LOC: Config.onoff.pipeline_prefetch
DEFAULT: off
DOC_START
	To boost the performance of pipelined requests to closer
	match that of a non-proxied environment Squid can try to fetch
	up to two requests in parallel from a pipeline.

	Defaults to off for bandwidth management and access logging
	reasons.
DOC_END

NAME: high_response_time_warning
TYPE: int
COMMENT: (msec)
LOC: Config.warnings.high_rptm
DEFAULT: 0
DOC_START
	If the one-minute median response time exceeds this value,
	Squid prints a WARNING with debug level 0 to get the
	administrators attention.  The value is in milliseconds.
DOC_END

NAME: high_page_fault_warning
TYPE: int
LOC: Config.warnings.high_pf
DEFAULT: 0
DOC_START
	If the one-minute average page fault rate exceeds this
	value, Squid prints a WARNING with debug level 0 to get
	the administrators attention.  The value is in page faults
	per second.
DOC_END

NAME: high_memory_warning
TYPE: b_size_t
LOC: Config.warnings.high_memory
DEFAULT: 0 KB
DOC_START
	If the memory usage (as determined by mallinfo) exceeds
	this amount, Squid prints a WARNING with debug level 0 to get
	the administrators attention.
DOC_END

NAME: sleep_after_fork
COMMENT: (microseconds)
TYPE: int
LOC: Config.sleep_after_fork
DEFAULT: 0
DOC_START
	When this is set to a non-zero value, the main Squid process
	sleeps the specified number of microseconds after a fork()
	system call. This sleep may help the situation where your
	system reports fork() failures due to lack of (virtual)
	memory. Note, however, if you have a lot of child
	processes, these sleep delays will add up and your
	Squid will not service requests for some amount of time
	until all the child processes have been started.
	On Windows value less then 1000 (1 milliseconds) are
	rounded to 1000.
DOC_END

NAME: windows_ipaddrchangemonitor
COMMENT: on|off
TYPE: onoff
DEFAULT: on
LOC: Config.onoff.WIN32_IpAddrChangeMonitor
DOC_START
	On Windows Squid by default will monitor IP address changes and will 
	reconfigure itself after any detected event. This is very useful for
	proxies connected to internet with dial-up interfaces.
	In some cases (a Proxy server acting as VPN gateway is one) it could be
	desiderable to disable this behaviour setting this to 'off'.
	Note: after changing this, Squid service must be restarted.
DOC_END

EOF