Bindings/media/i2c/st,st-mipid02.yaml

   1 # SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
   2 %YAML 1.2
   3 ---
   4 $id: http://devicetree.org/schemas/media/i2c/st,st-mipid02.yaml#
   5 $schema: http://devicetree.org/meta-schemas/core.yaml#
   6
   7 title: STMicroelectronics MIPID02 CSI-2 to PARALLEL bridge
   8
   9 maintainers:
  10   - Benjamin Mugnier <benjamin.mugnier@foss.st.com>
  11   - Sylvain Petinot <sylvain.petinot@foss.st.com>
  12
  13 description:
  14   MIPID02 has two CSI-2 input ports, only one of those ports can be
  15   active at a time. Active port input stream will be de-serialized
  16   and its content outputted through PARALLEL output port.
  17   CSI-2 first input port is a dual lane 800Mbps per lane whereas CSI-2
  18   second input port is a single lane 800Mbps. Both ports support clock
  19   and data lane polarity swap. First port also supports data lane swap.
  20   PARALLEL output port has a maximum width of 12 bits.
  21   Supported formats are RAW6, RAW7, RAW8, RAW10, RAW12, RGB565, RGB888,
  22   RGB444, YUV420 8-bit, YUV422 8-bit and YUV420 10-bit.
  23
  24 properties:
  25   compatible:
  26     const: st,st-mipid02
  27
  28   reg:
  29     maxItems: 1
  30
  31   clocks:
  32     maxItems: 1
  33
  34   clock-names:
  35     const: xclk
  36
  37   VDDE-supply:
  38     description:
  39       Sensor digital IO supply. Must be 1.8 volts.
  40
  41   VDDIN-supply:
  42     description:
  43       Sensor internal regulator supply. Must be 1.8 volts.
  44
  45   reset-gpios:
  46     description:
  47       Reference to the GPIO connected to the xsdn pin, if any.
  48       This is an active low signal to the mipid02.
  49
  50   ports:
  51     $ref: /schemas/graph.yaml#/properties/ports
  52     properties:
  53       port@0:
  54         $ref: /schemas/graph.yaml#/$defs/port-base
  55         unevaluatedProperties: false
  56         description: CSI-2 first input port
  57         properties:
  58           endpoint:
  59             $ref: /schemas/media/video-interfaces.yaml#
  60             unevaluatedProperties: false
  61
  62             properties:
  63               data-lanes:
  64                 description:
  65                   Single-lane operation shall be <1> or <2> .
  66                   Dual-lane operation shall be <1 2> or <2 1> .
  67                 minItems: 1
  68                 maxItems: 2
  69
  70               lane-polarities:
  71                 description:
  72                   Any lane can be inverted or not.
  73                 minItems: 1
  74                 maxItems: 2
  75
  76             required:
  77               - data-lanes
  78
  79       port@1:
  80         $ref: /schemas/graph.yaml#/$defs/port-base
  81         unevaluatedProperties: false
  82         description: CSI-2 second input port
  83         properties:
  84           endpoint:
  85             $ref: /schemas/media/video-interfaces.yaml#
  86             unevaluatedProperties: false
  87
  88             properties:
  89               data-lanes:
  90                 description:
  91                   Single-lane operation shall be <1> or <2> .
  92                 maxItems: 1
  93
  94               lane-polarities:
  95                 description:
  96                   Any lane can be inverted or not.
  97                 maxItems: 1
  98
  99             required:
 100               - data-lanes
 101
 102       port@2:
 103         $ref: /schemas/graph.yaml#/$defs/port-base
 104         unevaluatedProperties: false
 105         description: Output port
 106         properties:
 107           endpoint:
 108             $ref: /schemas/media/video-interfaces.yaml#
 109             unevaluatedProperties: false
 110
 111             properties:
 112               bus-width:
 113                 enum: [6, 7, 8, 10, 12]
 114
 115             required:
 116               - bus-width
 117
 118     anyOf:
 119       - required:
 120           - port@0
 121       - required:
 122           - port@1
 123
 124     required:
 125       - port@2
 126
 127 additionalProperties: false
 128
 129 required:
 130   - compatible
 131   - reg
 132   - clocks
 133   - clock-names
 134   - VDDE-supply
 135   - VDDIN-supply
 136   - ports
 137
 138 examples:
 139   - |
 140     i2c {
 141         #address-cells = <1>;
 142         #size-cells = <0>;
 143         mipid02: csi2rx@14 {
 144             compatible = "st,st-mipid02";
 145             reg = <0x14>;
 146             clocks = <&clk_ext_camera_12>;
 147             clock-names = "xclk";
 148             VDDE-supply = <&vdd>;
 149             VDDIN-supply = <&vdd>;
 150             ports {
 151                 #address-cells = <1>;
 152                 #size-cells = <0>;
 153                 port@0 {
 154                     reg = <0>;
 155
 156                     ep0: endpoint {
 157                         data-lanes = <1 2>;
 158                         remote-endpoint = <&mipi_csi2_in>;
 159                     };
 160                 };
 161                 port@2 {
 162                     reg = <2>;
 163
 164                     ep2: endpoint {
 165                         bus-width = <8>;
 166                         hsync-active = <0>;
 167                         vsync-active = <0>;
 168                         remote-endpoint = <&parallel_out>;
 169                     };
 170                 };
 171             };
 172         };
 173     };
 174
 175 ...