1 # SPDX-License-Identifier: GPL-2.0+
10 # To see a list of typical targets execute "make help"
11 # More info can be located in ./README
12 # Comments in this file are targeted only to the developer, do not
13 # expect to learn how to build the kernel reading this file.
15 # Do not use make's built-in rules and variables
16 # (this increases performance and avoids hard-to-debug behaviour)
19 # Determine target architecture for the sandbox
20 include include/host_arch.h
21 ifeq ("", "$(CROSS_COMPILE)")
22 MK_ARCH
="${shell uname -m}"
24 MK_ARCH
="${shell echo $(CROSS_COMPILE) | sed -n 's/^\s*\([^\/]*\/\)*\([^-]*\)-\S*/\2/p'}"
27 ifeq ("x86_64", $(MK_ARCH
))
28 export HOST_ARCH
=$(HOST_ARCH_X86_64
)
29 else ifneq (,$(findstring $(MK_ARCH
), "i386" "i486" "i586" "i686"))
30 export HOST_ARCH
=$(HOST_ARCH_X86
)
31 else ifneq (,$(findstring $(MK_ARCH
), "aarch64" "armv8l"))
32 export HOST_ARCH
=$(HOST_ARCH_AARCH64
)
33 else ifneq (,$(findstring $(MK_ARCH
), "arm" "armv7" "armv7l"))
34 export HOST_ARCH
=$(HOST_ARCH_ARM
)
35 else ifeq ("riscv32", $(MK_ARCH
))
36 export HOST_ARCH
=$(HOST_ARCH_RISCV32
)
37 else ifeq ("riscv64", $(MK_ARCH
))
38 export HOST_ARCH
=$(HOST_ARCH_RISCV64
)
42 # Avoid funny character set dependencies
46 export LC_COLLATE LC_NUMERIC
48 # Avoid interference with shell env settings
51 # We are using a recursive build, so we need to do a little thinking
52 # to get the ordering right.
54 # Most importantly: sub-Makefiles should only ever modify files in
55 # their own directory. If in some directory we have a dependency on
56 # a file in another dir (which doesn't happen often, but it's often
57 # unavoidable when linking the built-in.o targets which finally
58 # turn into vmlinux), we will call a sub make in that other dir, and
59 # after that we are sure that everything which is in that other dir
62 # The only cases where we need to modify files which have global
63 # effects are thus separated out and done before the recursive
64 # descending is started. They are now explicitly listed as the
68 # ---------------------------------------------------------------------------
70 # Normally, we echo the whole command before executing it. By making
71 # that echo $($(quiet)$(cmd)), we now have the possibility to set
72 # $(quiet) to choose other forms of output instead, e.g.
74 # quiet_cmd_cc_o_c = Compiling $(RELDIR)/$@
75 # cmd_cc_o_c = $(CC) $(c_flags) -c -o $@ $<
77 # If $(quiet) is empty, the whole command will be printed.
78 # If it is set to "quiet_", only the short version will be printed.
79 # If it is set to "silent_", nothing will be printed at all, since
80 # the variable $(silent_cmd_cc_o_c) doesn't exist.
82 # A simple variant is to prefix commands with $(Q) - that's useful
83 # for commands that shall be hidden in non-verbose mode.
87 # If KBUILD_VERBOSE equals 0 then the above command will be hidden.
88 # If KBUILD_VERBOSE equals 1 then the above command is displayed.
90 # To put more focus on warnings, be less verbose as default
91 # Use 'make V=1' to see the full commands
93 ifeq ("$(origin V)", "command line")
100 ifeq ($(KBUILD_VERBOSE
),1)
108 # If the user is running make -s (silent mode), suppress echoing of
111 ifneq ($(filter 4.
%,$(MAKE_VERSION
)),) # make-4
112 ifneq ($(filter %s
,$(firstword x
$(MAKEFLAGS
))),)
116 ifneq ($(filter s
% -s
%,$(MAKEFLAGS
)),)
121 export quiet Q KBUILD_VERBOSE
123 # kbuild supports saving output files in a separate directory.
124 # To locate output files in a separate directory two syntaxes are supported.
125 # In both cases the working directory must be the root of the kernel src.
127 # Use "make O=dir/to/store/output/files/"
129 # 2) Set KBUILD_OUTPUT
130 # Set the environment variable KBUILD_OUTPUT to point to the directory
131 # where the output files shall be placed.
132 # export KBUILD_OUTPUT=dir/to/store/output/files/
135 # The O= assignment takes precedence over the KBUILD_OUTPUT environment
138 # KBUILD_SRC is set on invocation of make in OBJ directory
139 # KBUILD_SRC is not intended to be used by the regular user (for now)
140 ifeq ($(KBUILD_SRC
),)
142 # OK, Make called in directory where kernel src resides
143 # Do we want to locate output files in a separate directory?
144 ifeq ("$(origin O)", "command line")
145 KBUILD_OUTPUT
:= $(O
)
148 # That's our default target when none is given on the command line
152 # Cancel implicit rules on top Makefile
153 $(CURDIR
)/Makefile Makefile
: ;
155 ifneq ($(KBUILD_OUTPUT
),)
156 # Invoke a second make in the output directory, passing relevant variables
157 # check that the output directory actually exists
158 saved-output
:= $(KBUILD_OUTPUT
)
159 KBUILD_OUTPUT
:= $(shell mkdir
-p
$(KBUILD_OUTPUT
) && cd
$(KBUILD_OUTPUT
) \
161 $(if
$(KBUILD_OUTPUT
),, \
162 $(error failed to create output directory
"$(saved-output)"))
164 # Look for make include files relative to root of kernel src
166 # This does not become effective immediately because MAKEFLAGS is re-parsed
167 # once after the Makefile is read. It is OK since we are going to invoke
169 MAKEFLAGS
+= --include-dir
=$(CURDIR
)
171 PHONY
+= $(MAKECMDGOALS
) sub-make
173 $(filter-out _all sub-make
$(CURDIR
)/Makefile
, $(MAKECMDGOALS
)) _all
: sub-make
177 $(Q
)$(MAKE
) -C
$(KBUILD_OUTPUT
) KBUILD_SRC
=$(CURDIR
) \
178 -f
$(CURDIR
)/Makefile
$(filter-out _all sub-make
,$(MAKECMDGOALS
))
180 # Leave processing to above invocation of make
182 endif # ifneq ($(KBUILD_OUTPUT),)
183 endif # ifeq ($(KBUILD_SRC),)
185 # We process the rest of the Makefile if this is the final invocation of make
186 ifeq ($(skip-makefile
),)
188 # Do not print "Entering directory ...",
189 # but we want to display it when entering to the output directory
190 # so that IDEs/editors are able to understand relative filenames.
191 MAKEFLAGS
+= --no-print-directory
193 # Call a source code checker (by default, "sparse") as part of the
196 # Use 'make C=1' to enable checking of only re-compiled files.
197 # Use 'make C=2' to enable checking of *all* source files, regardless
198 # of whether they are re-compiled or not.
200 # See the file "doc/sparse.txt" for more details, including
201 # where to get the "sparse" utility.
203 ifeq ("$(origin C)", "command line")
204 KBUILD_CHECKSRC
= $(C
)
206 ifndef KBUILD_CHECKSRC
210 # Use make M=dir to specify directory of external module to build
211 # Old syntax make ... SUBDIRS=$PWD is still supported
212 # Setting the environment variable KBUILD_EXTMOD take precedence
214 KBUILD_EXTMOD ?
= $(SUBDIRS
)
217 ifeq ("$(origin M)", "command line")
218 KBUILD_EXTMOD
:= $(M
)
221 # If building an external module we do not care about the all: rule
222 # but instead _all depend on modules
224 ifeq ($(KBUILD_EXTMOD
),)
230 ifeq ($(KBUILD_SRC
),)
231 # building in the source tree
234 ifeq ($(KBUILD_SRC
)/,$(dir $(CURDIR
)))
235 # building in a subdirectory of the source tree
238 srctree
:= $(KBUILD_SRC
)
245 VPATH
:= $(srctree
)$(if
$(KBUILD_EXTMOD
),:$(KBUILD_EXTMOD
))
247 export srctree objtree VPATH
249 # Make sure CDPATH settings don't interfere
252 #########################################################################
254 HOSTARCH
:= $(shell uname
-m | \
256 -e s
/sun4u
/sparc64
/ \
259 -e s
/ppc64
/powerpc
/ \
261 -e s
/macppc
/powerpc
/\
264 HOSTOS
:= $(shell uname
-s | tr
'[:upper:]' '[:lower:]' | \
265 sed
-e
's/\(cygwin\).*/cygwin/')
267 export HOSTARCH HOSTOS
269 #########################################################################
271 # set default to nothing for native builds
272 ifeq ($(HOSTARCH
),$(ARCH
))
276 KCONFIG_CONFIG ?
= .config
277 export KCONFIG_CONFIG
279 # SHELL used by kbuild
280 CONFIG_SHELL
:= $(shell if
[ -x
"$$BASH" ]; then echo
$$BASH; \
281 else if
[ -x
/bin
/bash
]; then echo
/bin
/bash
; \
282 else echo sh
; fi
; fi
)
284 HOST_LFS_CFLAGS
:= $(shell getconf LFS_CFLAGS
2>/dev
/null
)
285 HOST_LFS_LDFLAGS
:= $(shell getconf LFS_LDFLAGS
2>/dev
/null
)
286 HOST_LFS_LIBS
:= $(shell getconf LFS_LIBS
2>/dev
/null
)
290 KBUILD_HOSTCFLAGS
:= -Wall
-Wstrict-prototypes
-O2
-fomit-frame-pointer \
291 $(HOST_LFS_CFLAGS
) $(HOSTCFLAGS
)
292 KBUILD_HOSTCXXFLAGS
:= -O2
$(HOST_LFS_CFLAGS
) $(HOSTCXXFLAGS
)
293 KBUILD_HOSTLDFLAGS
:= $(HOST_LFS_LDFLAGS
) $(HOSTLDFLAGS
)
294 KBUILD_HOSTLDLIBS
:= $(HOST_LFS_LIBS
) $(HOSTLDLIBS
)
296 # With the move to GCC 6, we have implicitly upgraded our language
297 # standard to GNU11 (see https://gcc.gnu.org/gcc-5/porting_to.html).
298 # Some Linux distributions (including RHEL7, SLES13, Debian 8) still
299 # have older compilers as their default, so we make it explicit for
300 # these that our host tools are GNU11 (i.e. C11 w/ GNU extensions).
301 CSTD_FLAG
:= -std
=gnu11
302 KBUILD_HOSTCFLAGS
+= $(CSTD_FLAG
)
304 ifeq ($(HOSTOS
),cygwin
)
305 KBUILD_HOSTCFLAGS
+= -ansi
308 # Mac OS X / Darwin's C preprocessor is Apple specific. It
309 # generates numerous errors and warnings. We want to bypass it
310 # and use GNU C's cpp. To do this we pass the -traditional-cpp
311 # option to the compiler. Note that the -traditional-cpp flag
312 # DOES NOT have the same semantics as GNU C's flag, all it does
313 # is invoke the GNU preprocessor in stock ANSI/ISO C fashion.
315 # Apple's linker is similar, thanks to the new 2 stage linking
316 # multiple symbol definitions are treated as errors, hence the
317 # -multiply_defined suppress option to turn off this error.
319 ifeq ($(HOSTOS
),darwin
)
320 # get major and minor product version (e.g. '10' and '6' for Snow Leopard)
321 DARWIN_MAJOR_VERSION
= $(shell sw_vers
-productVersion | cut
-f
1 -d
'.')
322 DARWIN_MINOR_VERSION
= $(shell sw_vers
-productVersion | cut
-f
2 -d
'.')
324 os_x_before
= $(shell if
[ $(DARWIN_MAJOR_VERSION
) -le
$(1) -a \
325 $(DARWIN_MINOR_VERSION
) -le
$(2) ] ; then echo
"$(3)"; else echo
"$(4)"; fi
;)
327 os_x_after
= $(shell if
[ $(DARWIN_MAJOR_VERSION
) -ge
$(1) -a \
328 $(DARWIN_MINOR_VERSION
) -ge
$(2) ] ; then echo
"$(3)"; else echo
"$(4)"; fi
;)
330 # Snow Leopards build environment has no longer restrictions as described above
331 HOSTCC
= $(call os_x_before
, 10, 5, "cc", "gcc")
332 KBUILD_HOSTCFLAGS
+= $(call os_x_before
, 10, 4, "-traditional-cpp")
333 KBUILD_HOSTLDFLAGS
+= $(call os_x_before
, 10, 5, "-multiply_defined suppress")
335 # macOS Mojave (10.14.X)
336 # Undefined symbols for architecture x86_64: "_PyArg_ParseTuple"
337 KBUILD_HOSTLDFLAGS
+= $(call os_x_after
, 10, 14, "-lpython -dynamclib", "")
340 # Decide whether to build built-in, modular, or both.
341 # Normally, just do built-in.
346 # If we have only "make modules", don't compile built-in objects.
347 # When we're building modules with modversions, we need to consider
348 # the built-in objects during the descend as well, in order to
349 # make sure the checksums are up to date before we record them.
351 ifeq ($(MAKECMDGOALS
),modules
)
352 KBUILD_BUILTIN
:= $(if
$(CONFIG_MODVERSIONS
),1)
355 # If we have "make <whatever> modules", compile modules
356 # in addition to whatever we do anyway.
357 # Just "make" or "make all" shall build modules as well
359 # U-Boot does not need modules
360 #ifneq ($(filter all _all modules,$(MAKECMDGOALS)),)
361 # KBUILD_MODULES := 1
364 #ifeq ($(MAKECMDGOALS),)
365 # KBUILD_MODULES := 1
368 # Check ths size of a binary:
371 # #2: Size limit in bytes (decimal or 0xhex)
373 actual
=$$( wc
-c
$1 | awk
'{print $$1}'); \
374 limit
=$$( printf
"%d" $2 ); \
375 if
test $$actual -gt
$$limit; then \
376 echo
"$1 exceeds file size limit:" >&2; \
377 echo
" limit: $$(printf %#x $$limit) bytes" >&2; \
378 echo
" actual: $$(printf %#x $$actual) bytes" >&2; \
379 echo
" excess: $$(printf %#x $$((actual - limit))) bytes" >&2;\
385 export KBUILD_MODULES KBUILD_BUILTIN
386 export KBUILD_CHECKSRC KBUILD_SRC KBUILD_EXTMOD
388 # We need some generic definitions (do not try to remake the file).
389 scripts
/Kbuild.
include: ;
390 include scripts
/Kbuild.
include
392 # Make variables (CC, etc...)
394 AS
= $(CROSS_COMPILE
)as
396 ifneq ($(shell $(CROSS_COMPILE
)ld.bfd
-v
2> /dev
/null
),)
397 LD
= $(CROSS_COMPILE
)ld.bfd
399 LD
= $(CROSS_COMPILE
)ld
401 CC
= $(CROSS_COMPILE
)gcc
403 AR
= $(CROSS_COMPILE
)ar
404 NM
= $(CROSS_COMPILE
)nm
405 LDR
= $(CROSS_COMPILE
)ldr
406 STRIP
= $(CROSS_COMPILE
)strip
407 OBJCOPY
= $(CROSS_COMPILE
)objcopy
408 OBJDUMP
= $(CROSS_COMPILE
)objdump
417 # The devicetree compiler and pylibfdt are automatically built unless DTC is
418 # provided. If DTC is provided, it is assumed the pylibfdt is available too.
419 DTC_INTREE
:= $(objtree
)/scripts
/dtc
/dtc
421 DTC_MIN_VERSION
:= 010406
425 CHECKFLAGS
:= -D__linux__
-Dlinux
-D__STDC__
-Dunix
-D__unix__ \
426 -Wbitwise
-Wno-return-void
-D__CHECK_ENDIAN__
$(CF
)
428 KBUILD_CPPFLAGS
:= -D__KERNEL__
-D__UBOOT__
430 KBUILD_CFLAGS
:= -Wall
-Wstrict-prototypes \
431 -Wno-format-security \
432 -fno-builtin
-ffreestanding
$(CSTD_FLAG
)
433 KBUILD_CFLAGS
+= -fshort-wchar
-fno-strict-aliasing
434 KBUILD_AFLAGS
:= -D__ASSEMBLY__
437 ifeq ($(cc-name
),clang
)
438 ifneq ($(CROSS_COMPILE
),)
439 CLANG_TARGET
:= --target
=$(notdir $(CROSS_COMPILE
:%-=%))
440 GCC_TOOLCHAIN_DIR
:= $(dir $(shell which
$(LD
)))
441 CLANG_PREFIX
:= --prefix=$(GCC_TOOLCHAIN_DIR
)
442 GCC_TOOLCHAIN
:= $(realpath
$(GCC_TOOLCHAIN_DIR
)/..
)
444 ifneq ($(GCC_TOOLCHAIN
),)
445 CLANG_GCC_TC
:= --gcc-toolchain
=$(GCC_TOOLCHAIN
)
447 KBUILD_CFLAGS
+= $(CLANG_TARGET
) $(CLANG_GCC_TC
) $(CLANG_PREFIX
)
448 KBUILD_AFLAGS
+= $(CLANG_TARGET
) $(CLANG_GCC_TC
) $(CLANG_PREFIX
)
449 KBUILD_CFLAGS
+= $(call cc-option
, -no-integrated-as
)
450 KBUILD_AFLAGS
+= $(call cc-option
, -no-integrated-as
)
453 # Don't generate position independent code
454 KBUILD_CFLAGS
+= $(call cc-option
,-fno-PIE
)
455 KBUILD_AFLAGS
+= $(call cc-option
,-fno-PIE
)
457 # Read UBOOTRELEASE from include/config/uboot.release (if it exists)
458 UBOOTRELEASE
= $(shell cat
include/config
/uboot.release
2> /dev
/null
)
459 UBOOTVERSION
= $(VERSION
)$(if
$(PATCHLEVEL
),.
$(PATCHLEVEL
)$(if
$(SUBLEVEL
),.
$(SUBLEVEL
)))$(EXTRAVERSION
)
461 export VERSION PATCHLEVEL SUBLEVEL UBOOTRELEASE UBOOTVERSION
462 export ARCH CPU BOARD VENDOR SOC CPUDIR BOARDDIR
463 export CONFIG_SHELL HOSTCC KBUILD_HOSTCFLAGS CROSS_COMPILE AS LD CC
464 export CPP AR NM LDR STRIP OBJCOPY OBJDUMP KBUILD_HOSTLDFLAGS KBUILD_HOSTLDLIBS
465 export MAKE LEX YACC AWK PERL PYTHON PYTHON2 PYTHON3
466 export HOSTCXX KBUILD_HOSTCXXFLAGS CHECK CHECKFLAGS DTC DTC_FLAGS
468 export KBUILD_CPPFLAGS NOSTDINC_FLAGS UBOOTINCLUDE OBJCOPYFLAGS KBUILD_LDFLAGS
469 export KBUILD_CFLAGS KBUILD_AFLAGS
471 export CC_VERSION_TEXT
:= $(shell $(CC
) --version | head
-n
1)
473 # When compiling out-of-tree modules, put MODVERDIR in the module
474 # tree rather than in the kernel tree. The kernel tree might
476 export MODVERDIR
:= $(if
$(KBUILD_EXTMOD
),$(firstword $(KBUILD_EXTMOD
))/).tmp_versions
478 # Files to ignore in find ... statements
480 export RCS_FIND_IGNORE
:= \
( -name SCCS
-o
-name BitKeeper
-o
-name .svn
-o \
481 -name CVS
-o
-name .
pc -o
-name .hg
-o
-name .git \
) \
483 export RCS_TAR_IGNORE
:= --exclude SCCS
--exclude BitKeeper
--exclude .svn \
484 --exclude CVS
--exclude .
pc --exclude .hg
--exclude .git
486 # ===========================================================================
487 # Rules shared between *config targets and build targets
489 # Basic helpers built in scripts/
490 PHONY
+= scripts_basic
492 $(Q
)$(MAKE
) $(build
)=scripts
/basic
493 $(Q
)rm -f .tmp_quiet_recordmcount
495 # To avoid any implicit rule to kick in, define an empty command.
496 scripts
/basic
/%: scripts_basic
;
498 PHONY
+= outputmakefile
499 # outputmakefile generates a Makefile in the output directory, if using a
500 # separate output directory. This allows convenient use of make in the
503 ifneq ($(KBUILD_SRC
),)
504 $(Q
)ln
-fsn
$(srctree
) source
505 $(Q
)$(CONFIG_SHELL
) $(srctree
)/scripts
/mkmakefile
$(srctree
)
508 # To make sure we do not include .config for any of the *config targets
509 # catch them early, and hand them over to scripts/kconfig/Makefile
510 # It is allowed to specify more targets when calling make, including
511 # mixing *config targets and build targets.
512 # For example 'make oldconfig all'.
513 # Detect when mixed targets is specified, and make a second invocation
514 # of make so .config is not included in this case either (for *config).
516 version_h
:= include/generated
/version_autogenerated.h
517 timestamp_h
:= include/generated
/timestamp_autogenerated.h
518 defaultenv_h
:= include/generated
/defaultenv_autogenerated.h
519 dt_h
:= include/generated
/dt.h
520 env_h
:= include/generated
/environment.h
522 no-dot-config-targets
:= clean clobber mrproper
distclean \
523 help
%docs
check% coccicheck \
524 ubootversion backup tests
check qcheck tcheck
530 ifneq ($(filter $(no-dot-config-targets
), $(MAKECMDGOALS
)),)
531 ifeq ($(filter-out $(no-dot-config-targets
), $(MAKECMDGOALS
)),)
536 ifeq ($(KBUILD_EXTMOD
),)
537 ifneq ($(filter config
%config
,$(MAKECMDGOALS
)),)
539 ifneq ($(words $(MAKECMDGOALS
)),1)
545 ifeq ($(mixed-targets
),1)
546 # ===========================================================================
547 # We're called with mixed targets (*config and build targets).
548 # Handle them one by one.
550 PHONY
+= $(MAKECMDGOALS
) __build_one_by_one
552 $(filter-out __build_one_by_one
, $(MAKECMDGOALS
)): __build_one_by_one
557 for i in
$(MAKECMDGOALS
); do \
558 $(MAKE
) -f
$(srctree
)/Makefile
$$i; \
562 ifeq ($(config-targets
),1)
563 # ===========================================================================
564 # *config targets only - make sure prerequisites are updated, and descend
565 # in scripts/kconfig to make the *config target
567 KBUILD_DEFCONFIG
:= sandbox_defconfig
568 export KBUILD_DEFCONFIG KBUILD_KCONFIG
570 config
: scripts_basic outputmakefile FORCE
571 $(Q
)$(MAKE
) $(build
)=scripts
/kconfig
$@
573 %config
: scripts_basic outputmakefile FORCE
574 $(Q
)$(MAKE
) $(build
)=scripts
/kconfig
$@
577 # ===========================================================================
578 # Build targets only - this includes vmlinux, arch specific targets, clean
579 # targets and others. In general all targets except *config targets.
581 # Additional helpers built in scripts/
582 # Carefully list dependencies so we do not try to build scripts twice
585 scripts
: scripts_basic scripts_dtc
include/config
/auto.conf
586 $(Q
)$(MAKE
) $(build
)=$(@
)
588 ifeq ($(dot-config
),1)
590 -include include/config
/auto.conf
592 # Read in dependencies to all Kconfig* files, make sure to run
593 # oldconfig if changes are detected.
594 -include include/config
/auto.conf.cmd
596 # To avoid any implicit rule to kick in, define an empty command
597 $(KCONFIG_CONFIG
) include/config
/auto.conf.cmd
: ;
599 # If .config is newer than include/config/auto.conf, someone tinkered
600 # with it and forgot to run make oldconfig.
601 # if auto.conf.cmd is missing then we are probably in a cleaned tree so
602 # we execute the config step to be sure to catch updated Kconfig files
603 include/config
/%.conf
: $(KCONFIG_CONFIG
) include/config
/auto.conf.cmd
604 $(Q
)$(MAKE
) -f
$(srctree
)/Makefile syncconfig
605 @
# If the following part fails, include/config/auto.conf should be
606 @
# deleted so "make silentoldconfig" will be re-run on the next build.
607 $(Q
)$(MAKE
) -f
$(srctree
)/scripts
/Makefile.autoconf || \
608 { rm -f
include/config
/auto.conf
; false
; }
609 @
# include/config.h has been updated after "make silentoldconfig".
610 @
# We need to touch include/config/auto.conf so it gets newer
611 @
# than include/config.h.
612 @
# Otherwise, 'make silentoldconfig' would be invoked twice.
613 $(Q
)touch
include/config
/auto.conf
615 u-boot.cfg spl
/u-boot.cfg tpl
/u-boot.cfg
:
616 $(Q
)$(MAKE
) -f
$(srctree
)/scripts
/Makefile.autoconf
$(@
)
618 -include include/autoconf.mk
619 -include include/autoconf.mk.dep
621 # We want to include arch/$(ARCH)/config.mk only when include/config/auto.conf
622 # is up-to-date. When we switch to a different board configuration, old CONFIG
623 # macros are still remaining in include/config/auto.conf. Without the following
624 # gimmick, wrong config.mk would be included leading nasty warnings/errors.
625 ifneq ($(wildcard $(KCONFIG_CONFIG
)),)
626 ifneq ($(wildcard include/config
/auto.conf
),)
627 autoconf_is_old
:= $(shell find .
-path .
/$(KCONFIG_CONFIG
) -newer \
628 include/config
/auto.conf
)
629 ifeq ($(autoconf_is_old
),)
631 include arch
/$(ARCH
)/Makefile
636 # These are set by the arch-specific config.mk. Make sure they are exported
637 # so they can be used when building an EFI application.
638 export EFI_LDS
# Filename of EFI link script in arch/$(ARCH)/lib
639 export EFI_CRT0
# Filename of EFI CRT0 in arch/$(ARCH)/lib
640 export EFI_RELOC
# Filename of EFU relocation code in arch/$(ARCH)/lib
641 export CFLAGS_EFI
# Compiler flags to add when building EFI app
642 export CFLAGS_NON_EFI
# Compiler flags to remove when building EFI app
643 export EFI_TARGET
# binutils target if EFI is natively supported
645 # If board code explicitly specified LDSCRIPT or CONFIG_SYS_LDSCRIPT, use
646 # that (or fail if absent). Otherwise, search for a linker script in a
650 #LDSCRIPT := $(srctree)/board/$(BOARDDIR)/u-boot.lds.debug
651 ifdef CONFIG_SYS_LDSCRIPT
652 # need to strip off double quotes
653 LDSCRIPT
:= $(srctree
)/$(CONFIG_SYS_LDSCRIPT
:"%"=%)
657 # If there is no specified link script, we look in a number of places for it
659 ifeq ($(wildcard $(LDSCRIPT
)),)
660 LDSCRIPT
:= $(srctree
)/board
/$(BOARDDIR
)/u-boot.lds
662 ifeq ($(wildcard $(LDSCRIPT
)),)
663 LDSCRIPT
:= $(srctree
)/$(CPUDIR
)/u-boot.lds
665 ifeq ($(wildcard $(LDSCRIPT
)),)
666 LDSCRIPT
:= $(srctree
)/arch
/$(ARCH
)/cpu
/u-boot.lds
671 # Dummy target needed, because used as prerequisite
672 include/config
/auto.conf
: ;
673 endif # $(dot-config)
676 # Xtensa linker script cannot be preprocessed with -ansi because of
677 # preprocessor operations on strings that don't make C identifiers.
679 ifeq ($(CONFIG_XTENSA
),)
683 ifdef CONFIG_CC_OPTIMIZE_FOR_SIZE
691 export LTO_CFLAGS LTO_FINAL_LDFLAGS
693 ifeq ($(cc-name
),clang
)
695 LTO_FINAL_LDFLAGS
+= -flto
697 AR
= $(shell $(CC
) -print-prog-name
=llvm-ar
)
698 NM
= $(shell $(CC
) -print-prog-name
=llvm-nm
)
700 NPROC
:= $(shell nproc
2>/dev
/null || echo
1)
701 LTO_CFLAGS
+= -flto
=$(NPROC
)
702 LTO_FINAL_LDFLAGS
+= -fuse-linker-plugin
-flto
=$(NPROC
)
704 # use plugin aware tools
705 AR
= $(CROSS_COMPILE
)gcc-ar
706 NM
= $(CROSS_COMPILE
)gcc-nm
709 CFLAGS_NON_EFI
+= $(LTO_CFLAGS
)
711 KBUILD_CFLAGS
+= $(LTO_CFLAGS
)
714 ifeq ($(CONFIG_STACKPROTECTOR
),y
)
715 KBUILD_CFLAGS
+= $(call cc-option
,-fstack-protector-strong
)
716 CFLAGS_EFI
+= $(call cc-option
,-fno-stack-protector
)
718 KBUILD_CFLAGS
+= $(call cc-option
,-fno-stack-protector
)
720 KBUILD_CFLAGS
+= $(call cc-option
,-fno-delete-null-pointer-checks
)
722 # disable pointer signed / unsigned warnings in gcc 4.0
723 KBUILD_CFLAGS
+= -Wno-pointer-sign
725 # disable stringop warnings in gcc 8+
726 KBUILD_CFLAGS
+= $(call cc-disable-warning
, stringop-truncation
)
728 KBUILD_CFLAGS
+= $(call cc-disable-warning
, zero-length-bounds
)
729 KBUILD_CFLAGS
+= $(call cc-disable-warning
, array-bounds
)
730 KBUILD_CFLAGS
+= $(call cc-disable-warning
, stringop-overflow
)
732 # Enabled with W=2, disabled by default as noisy
733 KBUILD_CFLAGS
+= $(call cc-disable-warning
, maybe-uninitialized
)
735 # change __FILE__ to the relative path from the srctree
736 KBUILD_CFLAGS
+= $(call cc-option
,-fmacro-prefix-map
=$(srctree
)/=)
739 # $(KBUILD_AFLAGS) sets -g, which causes gcc to pass a suitable -g<format>
740 # option to the assembler.
743 # Report stack usage if supported
744 # ARC tools based on GCC 7.1 has an issue with stack usage
745 # with naked functions, see commit message for more details
747 ifeq ($(shell $(CONFIG_SHELL
) $(srctree
)/scripts
/gcc-stack-usage.sh
$(CC
)),y
)
748 KBUILD_CFLAGS
+= -fstack-usage
752 KBUILD_CFLAGS
+= $(call cc-option
,-Wno-format-nonliteral
)
753 KBUILD_CFLAGS
+= $(call cc-disable-warning
, address-of-packed-member
)
755 ifdef CONFIG_CC_IS_CLANG
756 KBUILD_CPPFLAGS
+= $(call cc-option
,-Qunused-arguments
,)
757 KBUILD_CFLAGS
+= $(call cc-disable-warning
, format-invalid-specifier
)
758 KBUILD_CFLAGS
+= $(call cc-disable-warning
, gnu
)
759 KBUILD_CFLAGS
+= $(call cc-disable-warning
, address-of-packed-member
)
760 # Quiet clang warning: comparison of unsigned expression < 0 is always false
761 KBUILD_CFLAGS
+= $(call cc-disable-warning
, tautological-compare
)
762 # CLANG uses a _MergedGlobals as optimization, but this breaks modpost, as the
763 # source of a reference will be _MergedGlobals and not on of the whitelisted names.
764 # See modpost pattern 2
765 KBUILD_CFLAGS
+= $(call cc-option
, -mno-global-merge
,)
766 KBUILD_CFLAGS
+= $(call cc-option
, -fcatch-undefined-behavior
)
769 # These warnings generated too much noise in a regular build.
770 # Use make W=1 to enable them (see scripts/Makefile.extrawarn)
771 KBUILD_CFLAGS
+= $(call cc-disable-warning
, unused-but-set-variable
)
773 # Prohibit date/time macros, which would make the build non-deterministic
774 KBUILD_CFLAGS
+= $(call cc-option
,-Werror
=date-time
)
776 include scripts
/Makefile.extrawarn
778 # Add user supplied CPPFLAGS, AFLAGS and CFLAGS as the last assignments
779 KBUILD_CPPFLAGS
+= $(KCPPFLAGS
)
780 KBUILD_AFLAGS
+= $(KAFLAGS
)
781 KBUILD_CFLAGS
+= $(KCFLAGS
)
783 KBUILD_HOSTCFLAGS
+= $(if
$(CONFIG_TOOLS_DEBUG
),-g
)
785 # Use UBOOTINCLUDE when you must reference the include/ directory.
786 # Needed to be compatible with the O= option
789 $(if
$(KBUILD_SRC
), -I
$(srctree
)/include) \
790 $(if
$(CONFIG_
$(SPL_
)SYS_THUMB_BUILD
), \
791 $(if
$(CONFIG_HAS_THUMB2
), \
792 $(if
$(CONFIG_CPU_V7M
), \
793 -I
$(srctree
)/arch
/arm
/thumb1
/include), \
794 -I
$(srctree
)/arch
/arm
/thumb1
/include)) \
795 -I
$(srctree
)/arch
/$(ARCH
)/include \
796 -include $(srctree
)/include/linux
/kconfig.h
798 NOSTDINC_FLAGS
+= -nostdinc
-isystem
$(shell $(CC
) -print-file-name
=include)
801 cpp_flags
:= $(KBUILD_CPPFLAGS
) $(PLATFORM_CPPFLAGS
) $(UBOOTINCLUDE
) \
803 c_flags
:= $(KBUILD_CFLAGS
) $(cpp_flags
)
805 #########################################################################
806 # U-Boot objects....order is important (i.e. start must be first)
808 HAVE_VENDOR_COMMON_LIB
= $(if
$(wildcard $(srctree
)/board
/$(VENDOR
)/common
/Makefile
),y
,n
)
810 libs-
$(CONFIG_API
) += api
/
811 libs-
$(HAVE_VENDOR_COMMON_LIB
) += board
/$(VENDOR
)/common
/
815 libs-
$(CONFIG_OF_EMBED
) += dts
/
822 libs-
$(CONFIG_SYS_FSL_DDR
) += drivers
/ddr
/fsl
/
823 libs-
$(CONFIG_SYS_FSL_MMDC
) += drivers
/ddr
/fsl
/
824 libs-
$(CONFIG_
$(SPL_
)ALTERA_SDRAM
) += drivers
/ddr
/altera
/
825 libs-y
+= drivers
/usb
/cdns3
/
826 libs-y
+= drivers
/usb
/dwc3
/
827 libs-y
+= drivers
/usb
/common
/
828 libs-y
+= drivers
/usb
/emul
/
829 libs-y
+= drivers
/usb
/eth
/
830 libs-
$(CONFIG_USB_DEVICE
) += drivers
/usb
/gadget
/
831 libs-
$(CONFIG_USB_GADGET
) += drivers
/usb
/gadget
/
832 libs-
$(CONFIG_USB_GADGET
) += drivers
/usb
/gadget
/udc
/
833 libs-y
+= drivers
/usb
/host
/
834 libs-y
+= drivers
/usb
/mtu3
/
835 libs-y
+= drivers
/usb
/musb
/
836 libs-y
+= drivers
/usb
/musb-new
/
837 libs-y
+= drivers
/usb
/phy
/
838 libs-y
+= drivers
/usb
/ulpi
/
842 libs-
$(CONFIG_UNIT_TEST
) += test/
843 libs-
$(CONFIG_UT_ENV
) += test/env
/
844 libs-
$(CONFIG_UT_OPTEE
) += test/optee
/
845 libs-
$(CONFIG_UT_OVERLAY
) += test/overlay
/
847 libs-y
+= $(if
$(BOARDDIR
),board
/$(BOARDDIR
)/)
849 libs-y
:= $(sort $(libs-y
))
851 u-boot-dirs
:= $(patsubst %/,%,$(filter %/, $(libs-y
))) tools examples
853 u-boot-alldirs
:= $(sort $(u-boot-dirs
) $(patsubst %/,%,$(filter %/, $(libs-
))))
855 libs-y
:= $(patsubst %/, %/built-in.o
, $(libs-y
))
857 u-boot-init
:= $(head-y
)
858 u-boot-main
:= $(libs-y
)
862 ifeq ($(CONFIG_USE_PRIVATE_LIBGCC
),y
)
863 PLATFORM_LIBGCC
= arch
/$(ARCH
)/lib
/lib.a
865 PLATFORM_LIBGCC
:= -L
$(shell dirname
`$(CC) $(c_flags) -print-libgcc-file-name`) -lgcc
867 PLATFORM_LIBS
+= $(PLATFORM_LIBGCC
)
869 ifdef CONFIG_CC_COVERAGE
870 KBUILD_CFLAGS
+= --coverage
871 PLATFORM_LIBGCC
+= -lgcov
875 export PLATFORM_LIBGCC
877 # Special flags for CPP when processing the linker script.
878 # Pass the version down so we can handle backwards compatibility
881 -include $(srctree
)/include/u-boot
/u-boot.lds.h \
883 $(shell $(LD
) --version | \
884 sed
-ne
's/GNU ld version \([0-9][0-9]*\)\.\([0-9][0-9]*\).*/-DLD_MAJOR=\1 -DLD_MINOR=\2/p')
886 #########################################################################
887 #########################################################################
889 ifneq ($(CONFIG_BOARD_SIZE_LIMIT
),)
890 BOARD_SIZE_CHECK
= @
$(call size_check
,$@
,$(CONFIG_BOARD_SIZE_LIMIT
))
895 ifneq ($(CONFIG_SPL_SIZE_LIMIT
),0x0)
896 SPL_SIZE_CHECK
= @
$(call size_check
,$@
,$$(tools
/spl_size_limit
))
901 ifneq ($(CONFIG_TPL_SIZE_LIMIT
),0x0)
902 TPL_SIZE_CHECK
= @
$(call size_check
,$@
,$(CONFIG_TPL_SIZE_LIMIT
))
907 # Statically apply RELA-style relocations (currently arm64 only)
908 # This is useful for arm64 where static relocation needs to be performed on
909 # the raw binary, but certain simulators only accept an ELF file (but don't
910 # do the relocation).
911 ifneq ($(CONFIG_STATIC_RELA
),)
912 # $(1) is u-boot ELF, $(2) is u-boot bin, $(3) is text base
913 quiet_cmd_static_rela
= RELOC
$@
915 start
=$$($(NM
) $(2) | grep __rel_dyn_start | cut
-f
1 -d
' '); \
916 end
=$$($(NM
) $(2) | grep __rel_dyn_end | cut
-f
1 -d
' '); \
917 tools
/relocate-rela
$(3) $(4) $$start $$end
919 quiet_cmd_static_rela
=
923 # Always append INPUTS so that arch config.mk's can add custom ones
924 INPUTS-y
+= u-boot.srec u-boot.bin u-boot.sym System.map binary_size_check
926 INPUTS-
$(CONFIG_ONENAND_U_BOOT
) += u-boot-onenand.bin
927 ifeq ($(CONFIG_SPL_FSL_PBL
),y
)
928 INPUTS-
$(CONFIG_RAMBOOT_PBL
) += u-boot-with-spl-pbl.bin
930 ifneq ($(CONFIG_NXP_ESBC
), y
)
931 # For Secure Boot The Image needs to be signed and Header must also
932 # be included. So The image has to be built explicitly
933 INPUTS-
$(CONFIG_RAMBOOT_PBL
) += u-boot.pbl
936 INPUTS-
$(CONFIG_SPL
) += spl
/u-boot-spl.bin
937 ifeq ($(CONFIG_MX6
)$(CONFIG_IMX_HAB
), yy
)
938 INPUTS-
$(CONFIG_SPL_FRAMEWORK
) += u-boot-ivt.img
940 ifeq ($(CONFIG_MX7
)$(CONFIG_IMX_HAB
), yy
)
941 INPUTS-
$(CONFIG_SPL_FRAMEWORK
) += u-boot-ivt.img
943 INPUTS-
$(CONFIG_SPL_FRAMEWORK
) += u-boot.img
946 INPUTS-
$(CONFIG_TPL
) += tpl
/u-boot-tpl.bin
947 INPUTS-
$(CONFIG_OF_SEPARATE
) += u-boot.dtb
948 INPUTS-
$(CONFIG_BINMAN_STANDALONE_FDT
) += u-boot.dtb
949 ifeq ($(CONFIG_SPL_FRAMEWORK
),y
)
950 INPUTS-
$(CONFIG_OF_SEPARATE
) += u-boot-dtb.img
952 INPUTS-
$(CONFIG_SANDBOX
) += u-boot.dtb
953 ifneq ($(CONFIG_SPL_TARGET
),)
954 INPUTS-
$(CONFIG_SPL
) += $(CONFIG_SPL_TARGET
:"%"=%)
956 INPUTS-
$(CONFIG_REMAKE_ELF
) += u-boot.elf
957 INPUTS-
$(CONFIG_EFI_APP
) += u-boot-app.efi
958 INPUTS-
$(CONFIG_EFI_STUB
) += u-boot-payload.efi
960 # Generate this input file for binman
961 ifeq ($(CONFIG_SPL
),)
962 INPUTS-
$(CONFIG_ARCH_MEDIATEK
) += u-boot-mtk.bin
965 # Add optional build target if defined in board/cpu/soc headers
966 ifneq ($(CONFIG_BUILD_TARGET
),)
967 INPUTS-y
+= $(CONFIG_BUILD_TARGET
:"%"=%)
970 ifeq ($(CONFIG_INIT_SP_RELATIVE
)$(CONFIG_OF_SEPARATE
),yy
)
971 INPUTS-y
+= init_sp_bss_offset_check
974 ifeq ($(CONFIG_MPC85xx
)$(CONFIG_OF_SEPARATE
),yy
)
975 INPUTS-y
+= u-boot-with-dtb.bin
978 ifeq ($(CONFIG_ARCH_ROCKCHIP
),y
)
979 # On ARM64 this target is produced by binman so we don't need this dep
980 ifeq ($(CONFIG_ARM64
),y
)
981 ifeq ($(CONFIG_SPL
),y
)
982 # TODO: Get binman to generate this too
983 INPUTS-y
+= u-boot-rockchip.bin
986 ifeq ($(CONFIG_SPL
),y
)
987 # Generate these inputs for binman which will create the output files
988 INPUTS-y
+= idbloader.img u-boot.img
993 INPUTS-
$(CONFIG_X86
) += u-boot-x86-start16.bin u-boot-x86-reset16.bin \
994 $(if
$(CONFIG_SPL_X86_16BIT_INIT
),spl
/u-boot-spl.bin
) \
995 $(if
$(CONFIG_TPL_X86_16BIT_INIT
),tpl
/u-boot-tpl.bin
)
997 LDFLAGS_u-boot
+= $(LDFLAGS_FINAL
)
999 # Avoid 'Not enough room for program headers' error on binutils 2.28 onwards.
1000 LDFLAGS_u-boot
+= $(call ld-option
, --no-dynamic-linker
)
1003 LDFLAGS_u-boot
+= -z notext
1005 LDFLAGS_u-boot
+= --build-id
=none
1007 ifeq ($(CONFIG_ARC
)$(CONFIG_NIOS2
)$(CONFIG_X86
)$(CONFIG_XTENSA
),)
1008 LDFLAGS_u-boot
+= -Ttext
$(CONFIG_SYS_TEXT_BASE
)
1011 # insure the checker run with the right endianness
1012 CHECKFLAGS
+= $(if
$(CONFIG_CPU_BIG_ENDIAN
),-mbig-endian
,-mlittle-endian
)
1014 # the checker needs the correct machine size
1015 CHECKFLAGS
+= $(if
$(CONFIG_64BIT
),-m64
,-m32
)
1017 # Normally we fill empty space with 0xff
1018 quiet_cmd_objcopy
= OBJCOPY
$@
1019 cmd_objcopy
= $(OBJCOPY
) --gap-fill
=0xff $(OBJCOPYFLAGS
) \
1020 $(OBJCOPYFLAGS_
$(@F
)) $< $@
1022 # Provide a version which does not do this, for use by EFI
1023 quiet_cmd_zobjcopy
= OBJCOPY
$@
1024 cmd_zobjcopy
= $(OBJCOPY
) $(OBJCOPYFLAGS
) $(OBJCOPYFLAGS_
$(@F
)) $< $@
1026 quiet_cmd_efipayload
= OBJCOPY
$@
1027 cmd_efipayload
= $(OBJCOPY
) -I binary
-O
$(EFIPAYLOAD_BFDTARGET
) -B
$(EFIPAYLOAD_BFDARCH
) $< $@
1029 MKIMAGEOUTPUT ?
= /dev
/null
1031 quiet_cmd_mkimage
= MKIMAGE
$@
1032 cmd_mkimage
= $(objtree
)/tools
/mkimage
$(MKIMAGEFLAGS_
$(@F
)) -d
$< $@ \
1033 >$(MKIMAGEOUTPUT
) $(if
$(KBUILD_VERBOSE
:0=), && cat
$(MKIMAGEOUTPUT
))
1035 quiet_cmd_mkfitimage
= MKIMAGE
$@
1036 cmd_mkfitimage
= $(objtree
)/tools
/mkimage
$(MKIMAGEFLAGS_
$(@F
)) \
1037 -f
$(U_BOOT_ITS
) -p
$(CONFIG_FIT_EXTERNAL_OFFSET
) $@ \
1038 >$(MKIMAGEOUTPUT
) $(if
$(KBUILD_VERBOSE
:0=), && cat
$(MKIMAGEOUTPUT
))
1040 quiet_cmd_cat
= CAT
$@
1041 cmd_cat
= cat
$(filter-out $(PHONY
), $^
) > $@
1043 append
= cat
$(filter-out $< $(PHONY
), $^
) >> $@
1045 quiet_cmd_pad_cat
= CAT
$@
1046 cmd_pad_cat
= $(cmd_objcopy
) && $(append
) ||
{ rm -f
$@
; false
; }
1048 quiet_cmd_lzma
= LZMA
$@
1049 cmd_lzma
= lzma
-c
-z
-k
-9 $< > $@
1053 quiet_cmd_cfgcheck
= CFGCHK
$2
1054 cmd_cfgcheck
= $(srctree
)/scripts
/check-config.sh
$2 \
1055 $(srctree
)/scripts
/config_whitelist.txt
$(srctree
)
1057 # Concat the value of all the CONFIGs (result is 'y' or 'yy', etc. )
1058 got
= $(foreach cfg
,$(1),$($(cfg
)))
1060 # expected value 'y for each one
1061 expect
= $(foreach cfg
,$(1),y
)
1063 # Show a deprecation message
1065 # 1: List of CONFIG_DM_... to migrate to (e.g. "CONFIG_DM_MMC CONFIG_BLK")
1066 # 2: Name of component (e.g . "Ethernet drivers")
1067 # 3: Release deadline (e.g. "v202.07")
1068 # 4: Condition to require before checking (e.g. "$(CONFIG_NET)")
1069 # Note: Script avoids bash construct, hence the strange double 'if'
1070 # (patches welcome!)
1072 @if
[ -n
"$(strip $(4))" ]; then if
[ "$(got)" != "$(expect)" ]; then \
1073 echo
>&2 "===================== WARNING ======================"; \
1074 echo
>&2 "This board does not use $(firstword $(1)) (Driver Model"; \
1075 echo
>&2 "for $(2)). Please update the board to use"; \
1076 echo
>&2 "$(firstword $(1)) before the $(3) release. Failure to"; \
1077 echo
>&2 "update by the deadline may result in board removal."; \
1078 echo
>&2 "See doc/driver-model/migration.rst for more info."; \
1079 echo
>&2 "===================================================="; \
1087 all: .binman_stamp inputs
1088 ifeq ($(CONFIG_BINMAN
),y
)
1089 $(call if_changed
,binman
)
1092 # Timestamp file to make sure that binman always runs
1093 .binman_stamp
: FORCE
1096 ifeq ($(CONFIG_DEPRECATED
),y
)
1097 $(warning
"You have deprecated configuration options enabled in your .config! Please check your configuration.")
1099 ifeq ($(CONFIG_OF_EMBED
)$(CONFIG_EFI_APP
),y
)
1100 @echo
>&2 "===================== WARNING ======================"
1101 @echo
>&2 "CONFIG_OF_EMBED is enabled. This option should only"
1102 @echo
>&2 "be used for debugging purposes. Please use"
1103 @echo
>&2 "CONFIG_OF_SEPARATE for boards in mainline."
1104 @echo
>&2 "See doc/README.fdt-control for more info."
1105 @echo
>&2 "===================================================="
1107 ifneq ($(CONFIG_SPL_FIT_GENERATOR
),)
1108 @echo
>&2 "===================== WARNING ======================"
1109 @echo
>&2 "This board uses CONFIG_SPL_FIT_GENERATOR. Please migrate"
1110 @echo
>&2 "to binman instead, to avoid the proliferation of"
1111 @echo
>&2 "arch-specific scripts with no tests."
1112 @echo
>&2 "===================================================="
1114 ifneq ($(CONFIG_DM
),y
)
1115 @echo
>&2 "===================== WARNING ======================"
1116 @echo
>&2 "This board does not use CONFIG_DM. CONFIG_DM will be"
1117 @echo
>&2 "compulsory starting with the v2020.01 release."
1118 @echo
>&2 "Failure to update may result in board removal."
1119 @echo
>&2 "See doc/driver-model/migration.rst for more info."
1120 @echo
>&2 "===================================================="
1122 $(call deprecated
,CONFIG_WDT
,DM watchdog
,v2019.10
,\
1123 $(CONFIG_WATCHDOG
)$(CONFIG_HW_WATCHDOG
))
1124 $(call deprecated
,CONFIG_DM_ETH
,Ethernet drivers
,v2020.07
,$(CONFIG_NET
))
1125 $(call deprecated
,CONFIG_DM_I2C
,I2C drivers
,v2022.04
,$(CONFIG_SYS_I2C_LEGACY
))
1126 @
# Check that this build does not use CONFIG options that we do not
1127 @
# know about unless they are in Kconfig. All the existing CONFIG
1128 @
# options are whitelisted, so new ones should not be added.
1129 $(call cmd
,cfgcheck
,u-boot.cfg
)
1135 $(Q
)$(MAKE
) $(build
)=dts dtbs
1137 quiet_cmd_copy
= COPY
$@
1140 ifeq ($(CONFIG_MULTI_DTB_FIT
),y
)
1142 ifeq ($(CONFIG_MULTI_DTB_FIT_LZO
),y
)
1143 FINAL_DTB_CONTAINER
= fit-dtb.blob.lzo
1144 else ifeq ($(CONFIG_MULTI_DTB_FIT_GZIP
),y
)
1145 FINAL_DTB_CONTAINER
= fit-dtb.blob.gz
1147 FINAL_DTB_CONTAINER
= fit-dtb.blob
1150 fit-dtb.blob.gz
: fit-dtb.blob
1153 fit-dtb.blob.lzo
: fit-dtb.blob
1156 fit-dtb.blob
: dts
/dt.dtb FORCE
1157 $(call if_changed
,mkimage
)
1158 ifneq ($(SOURCE_DATE_EPOCH
),)
1159 touch
-d @
$(SOURCE_DATE_EPOCH
) fit-dtb.blob
1160 chmod
0600 fit-dtb.blob
1163 MKIMAGEFLAGS_fit-dtb.blob
= -f auto
-A
$(ARCH
) -T firmware
-C none
-O u-boot \
1165 $(patsubst %,-b arch
/$(ARCH
)/dts
/%.dtb
,$(subst ",,$(CONFIG_OF_LIST))) -d /dev/null
1167 MKIMAGEFLAGS_fit-dtb.blob += -B 0x8
1170 u-boot-fit-dtb.bin: u-boot-nodtb.bin $(EXT_DTB)
1171 $(call if_changed,cat)
1173 u-boot-fit-dtb.bin: u-boot-nodtb.bin $(FINAL_DTB_CONTAINER)
1174 $(call if_changed,cat)
1177 u-boot.bin: u-boot-fit-dtb.bin FORCE
1178 $(call if_changed,copy)
1180 u-boot-dtb.bin: u-boot-nodtb.bin dts/dt.dtb FORCE
1181 $(call if_changed,cat)
1183 else ifeq ($(CONFIG_OF_SEPARATE),y)
1184 u-boot-dtb.bin: u-boot-nodtb.bin dts/dt.dtb FORCE
1185 $(call if_changed,cat)
1187 u-boot.bin: u-boot-dtb.bin FORCE
1188 $(call if_changed,copy)
1190 u-boot.bin: u-boot-nodtb.bin FORCE
1191 $(call if_changed,copy)
1194 # we call Makefile in arch/arm/mach-imx which
1195 # has targets which are dependent on targets defined
1196 # here. make could not resolve them and we must ensure
1197 # that they are finished before calling imx targets
1198 ifeq ($(CONFIG_MULTI_DTB_FIT),y)
1199 IMX_DEPS = u-boot-fit-dtb.bin
1202 %.imx: $(IMX_DEPS) %.bin
1203 $(Q)$(MAKE) $(build)=arch/arm/mach-imx $@
1207 $(Q)$(MAKE) $(build)=arch/arm/cpu/armv7/vf610 $@
1209 quiet_cmd_copy = COPY $@
1212 u-boot.dtb: dts/dt.dtb
1215 OBJCOPYFLAGS_u-boot.hex := -O ihex
1217 OBJCOPYFLAGS_u-boot.srec := -O srec
1219 u-boot.hex u-boot.srec: u-boot FORCE
1220 $(call if_changed,objcopy)
1222 OBJCOPYFLAGS_u-boot-elf.srec := $(OBJCOPYFLAGS_u-boot.srec)
1224 u-boot-elf.srec: u-boot.elf FORCE
1225 $(call if_changed,objcopy)
1227 OBJCOPYFLAGS_u-boot-spl.srec = $(OBJCOPYFLAGS_u-boot.srec)
1229 spl/u-boot-spl.srec: spl/u-boot-spl FORCE
1230 $(call if_changed,objcopy)
1233 $(Q)$(MAKE) $(build)=arch/arm/mach-rmobile $@
1235 OBJCOPYFLAGS_u-boot-nodtb.bin := -O binary \
1236 $(if $(CONFIG_X86_16BIT_INIT),-R .start16 -R .resetvec) \
1237 $(if $(CONFIG_MPC85XX_HAVE_RESET_VECTOR),-R .bootpg -R .resetvec)
1239 binary_size_check: u-boot-nodtb.bin FORCE
1240 @file_size=$(shell wc -c u-boot-nodtb.bin | awk '{print $$1}') ; \
1241 map_size=$(shell cat u-boot.map | \
1242 awk '/_image_copy_start/ {start = $$1} /_image_binary_end/ {end = $$1} END {if (start != "" && end != "") print "ibase
=16; " toupper(end) " - " toupper(start)}' \
1245 if [ "" != "$$map_size" ]; then \
1246 if test $$map_size -ne $$file_size; then \
1247 echo "u-boot.map shows a binary size of
$$map_size" >&2 ; \
1248 echo " but u-boot-nodtb.bin shows
$$file_size" >&2 ; \
1253 ifeq ($(CONFIG_INIT_SP_RELATIVE)$(CONFIG_OF_SEPARATE),yy)
1254 ifneq ($(CONFIG_SYS_MALLOC_F_LEN),)
1255 subtract_sys_malloc_f_len = space=$$(($${space} - $(CONFIG_SYS_MALLOC_F_LEN)))
1257 subtract_sys_malloc_f_len = true
1259 # The 1/4 margin below is somewhat arbitrary. The likely initial SP usage is
1260 # so low that the DTB could probably use 90%+ of the available space, for
1261 # current values of CONFIG_SYS_INIT_SP_BSS_OFFSET at least. However, let's be
1262 # safe for now and tweak this later if space becomes tight.
1263 # A rejected alternative would be to check that some absolute minimum stack
1264 # space was available. However, since CONFIG_SYS_INIT_SP_BSS_OFFSET is
1265 # deliberately build-specific, to take account of build-to-build stack usage
1266 # differences due to different feature sets, there is no common absolute value
1268 init_sp_bss_offset_check: u-boot.dtb FORCE
1269 @dtb_size=$(shell wc -c u-boot.dtb | awk '{print $$1}') ; \
1270 space=$(CONFIG_SYS_INIT_SP_BSS_OFFSET) ; \
1271 $(subtract_sys_malloc_f_len) ; \
1272 quarter_space=$$(($${space} / 4)) ; \
1273 if [ $${dtb_size} -gt $${quarter_space} ]; then \
1274 echo "u-boot.dtb is larger than
1 quarter of
" >&2 ; \
1275 echo "(CONFIG_SYS_INIT_SP_BSS_OFFSET
- CONFIG_SYS_MALLOC_F_LEN
)" >&2 ; \
1280 shell_cmd = { $(call echo-cmd,$(1)) $(cmd_$(1)); }
1282 quiet_cmd_objcopy_uboot = OBJCOPY $@
1283 ifdef cmd_static_rela
1284 cmd_objcopy_uboot = $(cmd_objcopy) && $(call shell_cmd,static_rela,$<,$@,$(CONFIG_SYS_TEXT_BASE)) || { rm -f $@; false; }
1286 cmd_objcopy_uboot = $(cmd_objcopy)
1289 u-boot-nodtb.bin: u-boot FORCE
1290 $(call if_changed,objcopy_uboot)
1295 $(LDR) -T $(CONFIG_CPU) -c $@ $< $(LDR_FLAGS)
1299 # ---------------------------------------------------------------------------
1300 # Use 'make BINMAN_DEBUG=1' to enable debugging
1301 # Use 'make BINMAN_VERBOSE=3' to set vebosity level
1302 default_dt := $(if $(DEVICE_TREE),$(DEVICE_TREE),$(CONFIG_DEFAULT_DEVICE_TREE))
1304 quiet_cmd_binman = BINMAN $@
1305 cmd_binman = $(srctree)/tools/binman/binman $(if $(BINMAN_DEBUG),-D) \
1306 --toolpath $(objtree)/tools \
1307 $(if $(BINMAN_VERBOSE),-v$(BINMAN_VERBOSE)) \
1308 build -u -d u-boot.dtb -O . -m --allow-missing \
1309 -I . -I $(srctree) -I $(srctree)/board/$(BOARDDIR) \
1310 -I arch/$(ARCH)/dts -a of-list=$(CONFIG_OF_LIST) \
1311 -a atf-bl31-path=${BL31} \
1312 -a opensbi-path=${OPENSBI} \
1313 -a default-dt=$(default_dt) \
1314 -a scp-path=$(SCP) \
1315 -a spl-bss-pad=$(if $(CONFIG_SPL_SEPARATE_BSS),,1) \
1316 -a tpl-bss-pad=$(if $(CONFIG_TPL_SEPARATE_BSS),,1) \
1317 -a spl-dtb=$(CONFIG_SPL_OF_REAL) \
1318 -a tpl-dtb=$(CONFIG_TPL_OF_REAL) \
1321 OBJCOPYFLAGS_u-boot.ldr.hex := -I binary -O ihex
1323 OBJCOPYFLAGS_u-boot.ldr.srec := -I binary -O srec
1325 u-boot.ldr.hex u-boot.ldr.srec: u-boot.ldr FORCE
1326 $(call if_changed,objcopy)
1329 # U-Boot entry point, needed for booting of full-blown U-Boot
1330 # from the SPL U-Boot version.
1332 ifndef CONFIG_SYS_UBOOT_START
1333 CONFIG_SYS_UBOOT_START := $(CONFIG_SYS_TEXT_BASE)
1336 # Boards with more complex image requirements can provide an .its source file
1337 # or a generator script
1338 # NOTE: Please do not use this. We are migrating away from Makefile rules to use
1340 ifneq ($(CONFIG_SPL_FIT_SOURCE),"")
1341 U_BOOT_ITS := u-boot.its
1342 $(U_BOOT_ITS): $(subst ",,$(CONFIG_SPL_FIT_SOURCE
))
1343 $(call if_changed
,copy
)
1345 ifneq ($(CONFIG_USE_SPL_FIT_GENERATOR
),)
1346 U_BOOT_ITS
:= u-boot.its
1347 ifeq ($(CONFIG_SPL_FIT_GENERATOR
),"arch/arm/mach-rockchip/make_fit_atf.py")
1348 U_BOOT_ITS_DEPS
+= u-boot
1350 $(U_BOOT_ITS
): $(U_BOOT_ITS_DEPS
) FORCE
1351 $(srctree
)/$(CONFIG_SPL_FIT_GENERATOR
) \
1352 $(patsubst %,arch
/$(ARCH
)/dts
/%.dtb
,$(subst ",,$(CONFIG_OF_LIST))) > $@
1356 ifdef CONFIG_SPL_LOAD_FIT
1357 MKIMAGEFLAGS_u-boot.img = -f auto -A $(ARCH) -T firmware -C none -O u-boot \
1358 -a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_UBOOT_START) \
1359 -p $(CONFIG_FIT_EXTERNAL_OFFSET) \
1360 -n "U-Boot
$(UBOOTRELEASE
) for
$(BOARD
) board
" -E \
1361 $(patsubst %,-b arch/$(ARCH)/dts/%.dtb,$(subst ",,$(DEVICE_TREE
))) \
1362 $(patsubst %,-b arch
/$(ARCH
)/dts
/%.dtb
,$(subst ",,$(CONFIG_OF_LIST))) \
1363 $(patsubst %,-b arch/$(ARCH)/dts/%.dtbo,$(subst ",,$(CONFIG_OF_OVERLAY_LIST
)))
1365 MKIMAGEFLAGS_u-boot.img
= -A
$(ARCH
) -T firmware
-C none
-O u-boot \
1366 -a
$(CONFIG_SYS_TEXT_BASE
) -e
$(CONFIG_SYS_UBOOT_START
) \
1367 -n
"U-Boot $(UBOOTRELEASE) for $(BOARD) board"
1368 MKIMAGEFLAGS_u-boot-ivt.img
= -A
$(ARCH
) -T firmware_ivt
-C none
-O u-boot \
1369 -a
$(CONFIG_SYS_TEXT_BASE
) -e
$(CONFIG_SYS_UBOOT_START
) \
1370 -n
"U-Boot $(UBOOTRELEASE) for $(BOARD) board"
1371 u-boot-ivt.img
: MKIMAGEOUTPUT
= u-boot-ivt.img.log
1374 MKIMAGEFLAGS_u-boot-dtb.img
= $(MKIMAGEFLAGS_u-boot.img
)
1376 # Some boards have the kwbimage.cfg file written in advance, while some
1377 # other boards generate it on the fly during the build in the build tree.
1378 # Let's check if the file exists in the build tree first, otherwise we
1379 # fall back to use the one in the source tree.
1380 KWD_CONFIG_FILE
= $(shell \
1381 if
[ -f
$(objtree
)/$(CONFIG_SYS_KWD_CONFIG
:"%"=%) ]; then \
1382 echo
-n
$(objtree
)/$(CONFIG_SYS_KWD_CONFIG
:"%"=%); \
1384 echo
-n
$(srctree
)/$(CONFIG_SYS_KWD_CONFIG
:"%"=%); \
1387 MKIMAGEFLAGS_u-boot.kwb
= -n
$(KWD_CONFIG_FILE
) \
1388 -T kwbimage
-a
$(CONFIG_SYS_TEXT_BASE
) -e
$(CONFIG_SYS_TEXT_BASE
)
1390 MKIMAGEFLAGS_u-boot-spl.kwb
= -n
$(KWD_CONFIG_FILE
) \
1391 -T kwbimage
-a
$(CONFIG_SYS_TEXT_BASE
) -e
$(CONFIG_SYS_TEXT_BASE
) \
1392 $(if
$(KEYDIR
),-k
$(KEYDIR
))
1394 MKIMAGEFLAGS_u-boot.pbl
= -n
$(srctree
)/$(CONFIG_SYS_FSL_PBL_RCW
:"%"=%) \
1395 -R
$(srctree
)/$(CONFIG_SYS_FSL_PBL_PBI
:"%"=%) -T pblimage
1397 ifeq ($(CONFIG_MPC85xx
)$(CONFIG_OF_SEPARATE
),yy
)
1398 UBOOT_BIN
:= u-boot-with-dtb.bin
1400 UBOOT_BIN
:= u-boot.bin
1403 MKIMAGEFLAGS_u-boot-lzma.img
= -A
$(ARCH
) -T standalone
-C lzma
-O u-boot \
1404 -a
$(CONFIG_SYS_TEXT_BASE
) -e
$(CONFIG_SYS_UBOOT_START
) \
1405 -n
"U-Boot $(UBOOTRELEASE) for $(BOARD) board"
1407 u-boot.bin.lzma
: u-boot.bin FORCE
1408 $(call if_changed
,lzma
)
1410 u-boot-lzma.img
: u-boot.bin.lzma FORCE
1411 $(call if_changed
,mkimage
)
1413 u-boot-dtb.img u-boot.img u-boot.kwb u-boot.pbl u-boot-ivt.img
: \
1414 $(if
$(CONFIG_SPL_LOAD_FIT
),u-boot-nodtb.bin \
1415 $(if
$(CONFIG_OF_SEPARATE
)$(CONFIG_OF_EMBED
)$(CONFIG_SANDBOX
)$(CONFIG_BINMAN_STANDALONE_FDT
),dts
/dt.dtb
) \
1416 ,$(UBOOT_BIN
)) FORCE
1417 $(call if_changed
,mkimage
)
1420 ifeq ($(CONFIG_SPL_LOAD_FIT_FULL
),y
)
1421 MKIMAGEFLAGS_u-boot.itb
=
1423 MKIMAGEFLAGS_u-boot.itb
= -E
1425 MKIMAGEFLAGS_u-boot.itb
+= -B
0x8
1428 u-boot.itb
: u-boot-nodtb.bin \
1429 $(if
$(CONFIG_OF_SEPARATE
)$(CONFIG_OF_EMBED
)$(CONFIG_SANDBOX
),dts
/dt.dtb
) \
1431 $(call if_changed
,mkfitimage
)
1435 u-boot-spl.kwb
: u-boot.bin spl
/u-boot-spl.bin FORCE
1436 $(call if_changed
,mkimage
)
1438 u-boot.sha1
: u-boot.bin
1439 tools
/ubsha1 u-boot.bin
1442 $(OBJDUMP
) -d
$< > $@
1444 ifneq ($(CONFIG_SPL_PAYLOAD
),)
1445 SPL_PAYLOAD
:= $(CONFIG_SPL_PAYLOAD
:"%"=%)
1447 SPL_PAYLOAD
:= u-boot.bin
1450 SPL_IMAGE
:= $(CONFIG_SPL_IMAGE
:"%"=%)
1452 OBJCOPYFLAGS_u-boot-with-spl.bin
= -I binary
-O binary \
1453 --pad-to
=$(CONFIG_SPL_PAD_TO
)
1454 u-boot-with-spl.bin
: $(SPL_IMAGE
) $(SPL_PAYLOAD
) FORCE
1455 $(call if_changed
,pad_cat
)
1457 ifeq ($(CONFIG_ARCH_ROCKCHIP
),y
)
1460 ifeq ($(CONFIG_SPL
)$(CONFIG_TPL
),yy
)
1461 MKIMAGEFLAGS_u-boot-tpl-rockchip.bin
= -n
$(CONFIG_SYS_SOC
) -T rksd
1462 tpl
/u-boot-tpl-rockchip.bin
: tpl
/u-boot-tpl.bin FORCE
1463 $(call if_changed
,mkimage
)
1464 idbloader.img
: tpl
/u-boot-tpl-rockchip.bin spl
/u-boot-spl.bin FORCE
1465 $(call if_changed
,cat
)
1467 MKIMAGEFLAGS_idbloader.img
= -n
$(CONFIG_SYS_SOC
) -T rksd
1468 idbloader.img
: spl
/u-boot-spl.bin FORCE
1469 $(call if_changed
,mkimage
)
1472 ifeq ($(CONFIG_ARM64
),y
)
1473 OBJCOPYFLAGS_u-boot-rockchip.bin
= -I binary
-O binary \
1474 --pad-to
=$(CONFIG_SPL_PAD_TO
) --gap-fill
=0xff
1475 u-boot-rockchip.bin
: idbloader.img u-boot.itb FORCE
1476 $(call if_changed
,pad_cat
)
1477 endif # CONFIG_ARM64
1479 endif # CONFIG_ARCH_ROCKCHIP
1481 ifeq ($(CONFIG_ARCH_LPC32XX
)$(CONFIG_SPL
),yy
)
1482 MKIMAGEFLAGS_lpc32xx-spl.img
= -T lpc32xximage
-a
$(CONFIG_SPL_TEXT_BASE
)
1484 lpc32xx-spl.img
: spl
/u-boot-spl.bin FORCE
1485 $(call if_changed
,mkimage
)
1487 OBJCOPYFLAGS_lpc32xx-boot-0.bin
= -I binary
-O binary
--pad-to
=$(CONFIG_SPL_PAD_TO
)
1489 lpc32xx-boot-0.bin
: lpc32xx-spl.img FORCE
1490 $(call if_changed
,objcopy
)
1492 OBJCOPYFLAGS_lpc32xx-boot-1.bin
= -I binary
-O binary
--pad-to
=$(CONFIG_SPL_PAD_TO
)
1494 lpc32xx-boot-1.bin
: lpc32xx-spl.img FORCE
1495 $(call if_changed
,objcopy
)
1497 lpc32xx-full.bin
: lpc32xx-boot-0.bin lpc32xx-boot-1.bin u-boot.img FORCE
1498 $(call if_changed
,cat
)
1502 OBJCOPYFLAGS_u-boot-with-tpl.bin
= -I binary
-O binary \
1503 --pad-to
=$(CONFIG_TPL_PAD_TO
)
1504 tpl
/u-boot-with-tpl.bin
: tpl
/u-boot-tpl.bin u-boot.bin FORCE
1505 $(call if_changed
,pad_cat
)
1507 SPL
: spl
/u-boot-spl.bin FORCE
1508 $(Q
)$(MAKE
) $(build
)=arch
/arm
/mach-imx
$@
1510 ifeq ($(CONFIG_ARCH_IMX8M
)$(CONFIG_ARCH_IMX8
), y
)
1511 ifeq ($(CONFIG_SPL_LOAD_IMX_CONTAINER
), y
)
1512 u-boot.cnt
: u-boot.bin FORCE
1513 $(Q
)$(MAKE
) $(build
)=arch
/arm
/mach-imx
$@
1515 flash.bin
: spl
/u-boot-spl.bin u-boot.cnt FORCE
1516 $(Q
)$(MAKE
) $(build
)=arch
/arm
/mach-imx
$@
1518 ifeq ($(CONFIG_BINMAN
),y
)
1519 flash.bin
: spl
/u-boot-spl.bin
$(INPUTS-y
) FORCE
1520 $(call if_changed
,binman
)
1521 $(Q
)$(MAKE
) $(build
)=arch
/arm
/mach-imx
$@
1523 flash.bin
: spl
/u-boot-spl.bin u-boot.itb FORCE
1524 $(Q
)$(MAKE
) $(build
)=arch
/arm
/mach-imx
$@
1529 u-boot.uim
: u-boot.bin FORCE
1530 $(Q
)$(MAKE
) $(build
)=arch
/arm
/mach-imx
$@
1532 u-boot-with-spl.imx u-boot-with-nand-spl.imx
: SPL
$(if
$(CONFIG_OF_SEPARATE
),u-boot.img
,u-boot.uim
) FORCE
1533 $(Q
)$(MAKE
) $(build
)=arch
/arm
/mach-imx
$@
1535 MKIMAGEFLAGS_u-boot.ubl
= -n
$(UBL_CONFIG
) -T ublimage
-e
$(CONFIG_SYS_TEXT_BASE
)
1537 u-boot.ubl
: u-boot-with-spl.bin FORCE
1538 $(call if_changed
,mkimage
)
1540 MKIMAGEFLAGS_u-boot-spl.ais
= -s
-n
$(if
$(CONFIG_AIS_CONFIG_FILE
), \
1541 $(srctree
)/$(CONFIG_AIS_CONFIG_FILE
:"%"=%),"/dev/null") \
1542 -T aisimage
-e
$(CONFIG_SPL_TEXT_BASE
)
1543 spl
/u-boot-spl.ais
: spl
/u-boot-spl.bin FORCE
1544 $(call if_changed
,mkimage
)
1546 OBJCOPYFLAGS_u-boot.ais
= -I binary
-O binary
--pad-to
=$(CONFIG_SPL_PAD_TO
)
1547 u-boot.ais
: spl
/u-boot-spl.ais u-boot.img FORCE
1548 $(call if_changed
,pad_cat
)
1550 u-boot-signed.sb
: u-boot.bin spl
/u-boot-spl.bin
1551 $(Q
)$(MAKE
) $(build
)=arch
/arm
/cpu
/arm926ejs
/mxs u-boot-signed.sb
1552 u-boot.sb
: u-boot.bin spl
/u-boot-spl.bin
1553 $(Q
)$(MAKE
) $(build
)=arch
/arm
/cpu
/arm926ejs
/mxs u-boot.sb
1555 MKIMAGEFLAGS_u-boot-spl.img
= -A
$(ARCH
) -T firmware
-C none \
1556 -a
$(CONFIG_SPL_TEXT_BASE
) -e
$(CONFIG_SPL_TEXT_BASE
) -n XLOADER
1557 spl
/u-boot-spl.img
: spl
/u-boot-spl.bin FORCE
1558 $(call if_changed
,mkimage
)
1560 ifneq ($(CONFIG_ARCH_SOCFPGA
),)
1561 quiet_cmd_gensplx4
= GENSPLX4
$@
1562 cmd_gensplx4
= $(OBJCOPY
) -I binary
-O binary
--gap-fill
=0x0 \
1563 --pad-to
=$(CONFIG_SPL_PAD_TO
) \
1564 spl
/u-boot-spl.sfp spl
/u-boot-spl.sfp
&& \
1565 cat spl
/u-boot-spl.sfp spl
/u-boot-spl.sfp \
1566 spl
/u-boot-spl.sfp spl
/u-boot-spl.sfp
> $@ ||
{ rm -f
$@
; false
; }
1567 spl
/u-boot-splx4.sfp
: spl
/u-boot-spl.sfp FORCE
1568 $(call if_changed
,gensplx4
)
1570 quiet_cmd_socboot
= SOCBOOT
$@
1571 cmd_socboot
= cat spl
/u-boot-splx4.sfp u-boot.img
> $@ ||
{ rm -f
$@
; false
; }
1572 u-boot-with-spl.sfp
: spl
/u-boot-splx4.sfp u-boot.img FORCE
1573 $(call if_changed
,socboot
)
1575 quiet_cmd_gensplpadx4
= GENSPLPADX4
$@
1576 cmd_gensplpadx4
= dd if
=/dev
/zero of
=spl
/u-boot-spl.pad bs
=64 count
=1024 ; \
1577 cat spl
/u-boot-spl.sfp spl
/u-boot-spl.pad \
1578 spl
/u-boot-spl.sfp spl
/u-boot-spl.pad \
1579 spl
/u-boot-spl.sfp spl
/u-boot-spl.pad \
1580 spl
/u-boot-spl.sfp spl
/u-boot-spl.pad
> $@ || \
1581 { rm -f
$@ spl
/u-boot-spl.pad
; false
; }
1582 u-boot-spl-padx4.sfp
: spl
/u-boot-spl.sfp FORCE
1583 $(call if_changed
,gensplpadx4
)
1585 quiet_cmd_socnandboot
= SOCNANDBOOT
$@
1586 cmd_socnandboot
= cat u-boot-spl-padx4.sfp u-boot.img
> $@ ||
{ rm -f
$@
; false
; }
1587 u-boot-with-nand-spl.sfp
: u-boot-spl-padx4.sfp u-boot.img FORCE
1588 $(call if_changed
,socnandboot
)
1592 ifeq ($(CONFIG_MPC85xx
)$(CONFIG_OF_SEPARATE
),yy
)
1593 u-boot-with-dtb.bin
: u-boot.bin u-boot.dtb \
1594 $(if
$(CONFIG_MPC85XX_HAVE_RESET_VECTOR
), u-boot-br.bin
) FORCE
1595 $(call if_changed
,binman
)
1597 ifeq ($(CONFIG_MPC85XX_HAVE_RESET_VECTOR
),y
)
1598 OBJCOPYFLAGS_u-boot-br.bin
:= -O binary
-j .bootpg
-j .resetvec
1599 u-boot-br.bin
: u-boot FORCE
1600 $(call if_changed
,objcopy
)
1604 quiet_cmd_ldr
= LD
$@
1605 cmd_ldr
= $(LD
) $(LDFLAGS_
$(@F
)) \
1606 $(filter-out FORCE
,$^
) -o
$@
1609 OBJCOPYFLAGS_u-boot-x86-start16.bin
:= -O binary
-j .start16
1610 u-boot-x86-start16.bin
: u-boot FORCE
1611 $(call if_changed
,objcopy
)
1613 OBJCOPYFLAGS_u-boot-x86-reset16.bin
:= -O binary
-j .resetvec
1614 u-boot-x86-reset16.bin
: u-boot FORCE
1615 $(call if_changed
,objcopy
)
1619 OBJCOPYFLAGS_u-boot-app.efi
:= $(OBJCOPYFLAGS_EFI
)
1620 u-boot-app.efi
: u-boot FORCE
1621 $(call if_changed
,zobjcopy
)
1623 u-boot.bin.o
: u-boot.bin FORCE
1624 $(call if_changed
,efipayload
)
1626 u-boot-payload.lds
: $(LDSCRIPT_EFI
) FORCE
1627 $(call if_changed_dep
,cpp_lds
)
1629 # Rule to link the EFI payload which contains a stub and a U-Boot binary
1630 quiet_cmd_u-boot_payload ?
= LD
$@
1631 cmd_u-boot_payload ?
= $(LD
) $(LDFLAGS_EFI_PAYLOAD
) -o
$@ \
1632 -T u-boot-payload.lds arch
/x86
/cpu
/call32.o \
1633 lib
/efi
/efi.o lib
/efi
/efi_stub.o u-boot.bin.o \
1634 $(addprefix arch
/$(ARCH
)/lib
/,$(EFISTUB
))
1636 u-boot-payload
: u-boot.bin.o u-boot-payload.lds FORCE
1637 $(call if_changed
,u-boot_payload
)
1639 OBJCOPYFLAGS_u-boot-payload.efi
:= $(OBJCOPYFLAGS_EFI
)
1640 u-boot-payload.efi
: u-boot-payload FORCE
1641 $(call if_changed
,zobjcopy
)
1643 u-boot-img.bin
: spl
/u-boot-spl.bin u-boot.img FORCE
1644 $(call if_changed
,cat
)
1646 #Add a target to create boot binary having SPL binary in PBI format
1647 #concatenated with u-boot binary. It is need by PowerPC SoC having
1648 #internal SRAM <= 512KB.
1649 MKIMAGEFLAGS_u-boot-spl.pbl
= -n
$(srctree
)/$(CONFIG_SYS_FSL_PBL_RCW
:"%"=%) \
1650 -R
$(srctree
)/$(CONFIG_SYS_FSL_PBL_PBI
:"%"=%) -T pblimage \
1651 -A
$(ARCH
) -a
$(CONFIG_SPL_TEXT_BASE
)
1653 spl
/u-boot-spl.pbl
: spl
/u-boot-spl.bin FORCE
1654 $(call if_changed
,mkimage
)
1657 UBOOT_BINLOAD
:= u-boot.img
1659 ifeq ($(CONFIG_MPC85xx
)$(CONFIG_OF_SEPARATE
),yy
)
1660 UBOOT_BINLOAD
:= u-boot-with-dtb.bin
1662 UBOOT_BINLOAD
:= u-boot.bin
1666 OBJCOPYFLAGS_u-boot-with-spl-pbl.bin
= -I binary
-O binary
--pad-to
=$(CONFIG_SPL_PAD_TO
) \
1669 u-boot-with-spl-pbl.bin
: spl
/u-boot-spl.pbl
$(UBOOT_BINLOAD
) FORCE
1670 $(call if_changed
,pad_cat
)
1672 # PPC4xx needs the SPL at the end of the image, since the reset vector
1673 # is located at 0xfffffffc. So we can't use the "u-boot-img.bin" target
1674 # and need to introduce a new build target with the full blown U-Boot
1675 # at the start padded up to the start of the SPL image. And then concat
1676 # the SPL image to the end.
1678 OBJCOPYFLAGS_u-boot-img-spl-at-end.bin
:= -I binary
-O binary \
1679 --pad-to
=$(CONFIG_UBOOT_PAD_TO
) --gap-fill
=0xff
1680 u-boot-img-spl-at-end.bin
: u-boot.img spl
/u-boot-spl.bin FORCE
1681 $(call if_changed
,pad_cat
)
1683 quiet_cmd_u-boot-elf ?
= LD
$@
1684 cmd_u-boot-elf ?
= $(LD
) u-boot-elf.o
-o
$@ \
1685 -T u-boot-elf.lds
--defsym
=$(CONFIG_PLATFORM_ELFENTRY
)=$(CONFIG_SYS_TEXT_BASE
) \
1686 -Ttext
=$(CONFIG_SYS_TEXT_BASE
)
1687 u-boot.elf
: u-boot.bin u-boot-elf.lds
1688 $(Q
)$(OBJCOPY
) -I binary
$(PLATFORM_ELFFLAGS
) $< u-boot-elf.o
1689 $(call if_changed
,u-boot-elf
)
1691 u-boot-elf.lds
: arch
/u-boot-elf.lds prepare FORCE
1692 $(call if_changed_dep
,cpp_lds
)
1694 # MediaTek's ARM-based u-boot needs a header to contains its load address
1695 # which is parsed by the BootROM.
1696 # If the SPL build is enabled, the header will be added to the spl binary,
1697 # and the spl binary and the u-boot.img will be combined into one file.
1698 # Otherwise the header will be added to the u-boot.bin directly.
1700 ifeq ($(CONFIG_SPL
),y
)
1701 spl
/u-boot-spl-mtk.bin
: spl
/u-boot-spl
1703 u-boot-mtk.bin
: u-boot-with-spl.bin
1704 $(call if_changed
,copy
)
1706 MKIMAGEFLAGS_u-boot-mtk.bin
= -T mtk_image \
1707 -a
$(CONFIG_SYS_TEXT_BASE
) -e
$(CONFIG_SYS_TEXT_BASE
) \
1708 -n
"$(patsubst "%",%,$(CONFIG_MTK_BROM_HEADER_INFO))"
1710 u-boot-mtk.bin
: u-boot.bin FORCE
1711 $(call if_changed
,mkimage
)
1714 quiet_cmd_endian_swap
= SWAP
$@
1715 cmd_endian_swap
= $(srctree
)/tools
/endian-swap.py
$< $@
1717 u-boot-swap.bin
: u-boot.bin FORCE
1718 $(call if_changed
,endian_swap
)
1720 ARCH_POSTLINK
:= $(wildcard $(srctree
)/arch
/$(ARCH
)/Makefile.postlink
)
1722 # Generate linker list symbols references to force compiler to not optimize
1723 # them away when compiling with LTO
1725 u-boot-keep-syms-lto
:= keep-syms-lto.o
1726 u-boot-keep-syms-lto_c
:= $(patsubst %.o
,%.c
,$(u-boot-keep-syms-lto
))
1728 quiet_cmd_keep_syms_lto
= KSL
$@
1729 cmd_keep_syms_lto
= \
1730 $(srctree
)/scripts
/gen_ll_addressable_symbols.sh
$(NM
) $^
> $@
1732 quiet_cmd_keep_syms_lto_cc
= KSLCC
$@
1733 cmd_keep_syms_lto_cc
= \
1734 $(CC
) $(filter-out $(LTO_CFLAGS
),$(c_flags
)) -c
-o
$@
$<
1736 $(u-boot-keep-syms-lto_c
): $(u-boot-main
)
1737 $(call if_changed
,keep_syms_lto
)
1738 $(u-boot-keep-syms-lto
): $(u-boot-keep-syms-lto_c
)
1739 $(call if_changed
,keep_syms_lto_cc
)
1741 u-boot-keep-syms-lto
:=
1744 # Rule to link u-boot
1745 # May be overridden by arch/$(ARCH)/config.mk
1747 quiet_cmd_u-boot__ ?
= LTO
$@
1749 $(CC
) -nostdlib
-nostartfiles \
1750 $(LTO_FINAL_LDFLAGS
) $(c_flags
) \
1751 $(KBUILD_LDFLAGS
:%=-Wl
,%) $(LDFLAGS_u-boot
:%=-Wl
,%) -o
$@ \
1752 -T u-boot.lds
$(u-boot-init
) \
1753 -Wl
,--whole-archive \
1755 $(u-boot-keep-syms-lto
) \
1757 -Wl
,--no-whole-archive \
1758 -Wl
,-Map
,u-boot.map
; \
1759 $(if
$(ARCH_POSTLINK
), $(MAKE
) -f
$(ARCH_POSTLINK
) $@
, true
)
1761 # Note: Linking efi-x86_app64 causes a segfault in the linker at present
1762 # when using x86_64-linux-gnu-ld.bfd
1763 # For now, disable --whole-archive which makes things link, although not
1765 quiet_cmd_u-boot__ ?
= LD
$@
1766 cmd_u-boot__ ?
= $(LD
) $(KBUILD_LDFLAGS
) $(LDFLAGS_u-boot
) -o
$@ \
1767 -T u-boot.lds
$(u-boot-init
) \
1768 $(if
$(CONFIG_EFI_APP_64BIT
),,--whole-archive
) \
1770 $(if
$(CONFIG_EFI_APP_64BIT
),,--no-whole-archive
) \
1771 $(PLATFORM_LIBS
) -Map u-boot.map
; \
1772 $(if
$(ARCH_POSTLINK
), $(MAKE
) -f
$(ARCH_POSTLINK
) $@
, true
)
1775 quiet_cmd_smap
= GEN common
/system_map.o
1777 smap
=`$(call SYSTEM_MAP,u-boot) | \
1778 awk '$$2 ~ /[tTwW]/ {printf $$1 $$3 "\\\\000"}'` ; \
1779 $(CC
) $(c_flags
) -DSYSTEM_MAP
="\"$${smap}\"" \
1780 -c
$(srctree
)/common
/system_map.c
-o common
/system_map.o
1782 u-boot
: $(u-boot-init
) $(u-boot-main
) $(u-boot-keep-syms-lto
) u-boot.lds FORCE
1783 +$(call if_changed
,u-boot__
)
1784 ifeq ($(CONFIG_KALLSYMS
),y
)
1786 $(call cmd
,u-boot__
) common
/system_map.o
1789 ifeq ($(CONFIG_RISCV
),y
)
1790 @tools
/prelink-riscv
$@
0
1793 quiet_cmd_sym ?
= SYM
$@
1794 cmd_sym ?
= $(OBJDUMP
) -t
$< > $@
1795 u-boot.sym
: u-boot FORCE
1796 $(call if_changed
,sym
)
1798 # Environment processing
1799 # ---------------------------------------------------------------------------
1801 # Directory where we expect the .env file, if it exists
1802 ENV_DIR
:= $(srctree
)/board
/$(BOARDDIR
)
1804 # Basename of .env file, stripping quotes
1805 ENV_SOURCE_FILE
:= $(CONFIG_ENV_SOURCE_FILE
:"%"=%)
1807 # Filename of .env file
1808 ENV_FILE_CFG
:= $(ENV_DIR
)/$(ENV_SOURCE_FILE
).env
1810 # Default filename, if CONFIG_ENV_SOURCE_FILE is empty
1811 ENV_FILE_BOARD
:= $(ENV_DIR
)/$(CONFIG_SYS_BOARD
:"%"=%).env
1813 # Select between the CONFIG_ENV_SOURCE_FILE and the default one
1814 ENV_FILE
:= $(if
$(ENV_SOURCE_FILE
),$(ENV_FILE_CFG
),$(wildcard $(ENV_FILE_BOARD
)))
1816 # Run the environment text file through the preprocessor, but only if it is
1817 # non-empty, to save time and possible build errors if something is wonky with
1819 quiet_cmd_gen_envp
= ENVP
$@
1821 if
[ -s
"$(ENV_FILE)" ]; then \
1822 $(CPP
) -P
$(CFLAGS
) -x assembler-with-cpp
-D__ASSEMBLY__ \
1823 -D__UBOOT_CONFIG__ \
1824 -I .
-I
include -I
$(srctree
)/include \
1825 -include linux
/kconfig.h
-include include/config.h \
1826 -I
$(srctree
)/arch
/$(ARCH
)/include \
1831 include/generated
/env.in
: include/generated
/env.txt FORCE
1832 $(call cmd
,gen_envp
)
1834 # Regenerate the environment if it changes
1835 # We use 'wildcard' since the file is not required to exist (at present), in
1836 # which case we don't want this dependency, but instead should create an empty
1838 # This rule is useful since it shows the source file for the environment
1839 quiet_cmd_envc
= ENVC
$@
1841 if
[ -f
"$<" ]; then \
1843 elif
[ -n
"$(ENV_SOURCE_FILE)" ]; then \
1844 echo
"Missing file $(ENV_FILE_CFG)"; \
1849 include/generated
/env.txt
: $(wildcard $(ENV_FILE
)) FORCE
1852 # Write out the resulting environment, converted to a C string
1853 quiet_cmd_gen_envt
= ENVT
$@
1855 awk
-f
$(srctree
)/scripts
/env2string.awk
$< >$@
1856 $(env_h
): include/generated
/env.in
1857 $(call cmd
,gen_envt
)
1859 # ---------------------------------------------------------------------------
1861 # The actual objects are generated when descending,
1862 # make sure no implicit rule kicks in
1863 $(sort $(u-boot-init
) $(u-boot-main
)): $(u-boot-dirs
) ;
1865 # Handle descending into subdirectories listed in $(u-boot-dirs)
1866 # Preset locale variables to speed up the build process. Limit locale
1867 # tweaks to this spot to avoid wrong language settings when running
1868 # make menuconfig etc.
1869 # Error messages still appears in the original language
1871 PHONY
+= $(u-boot-dirs
)
1872 $(u-boot-dirs
): prepare scripts
1873 $(Q
)$(MAKE
) $(build
)=$@
1876 # The "tools" are needed early
1877 $(filter-out tools
, $(u-boot-dirs
)): tools
1878 # The "examples" conditionally depend on U-Boot (say, when USE_PRIVATE_LIBGCC
1879 # is "yes"), so compile examples after U-Boot is compiled.
1880 examples
: $(filter-out examples
, $(u-boot-dirs
))
1882 define filechk_uboot.release
1883 echo
"$(UBOOTVERSION)$$($(CONFIG_SHELL) $(srctree)/scripts/setlocalversion $(srctree))"
1886 # Store (new) UBOOTRELEASE string in include/config/uboot.release
1887 include/config
/uboot.release
: include/config
/auto.conf FORCE
1888 $(call filechk
,uboot.release
)
1891 # Things we need to do before we recursively start building the kernel
1892 # or the modules are listed in "prepare".
1893 # A multi level approach is used. prepareN is processed before prepareN-1.
1894 # archprepare is used in arch Makefiles and when processed asm symlink,
1895 # version.h and scripts_basic is processed / created.
1897 # Listed in dependency order
1898 PHONY
+= prepare archprepare prepare0 prepare1 prepare2 prepare3
1900 # prepare3 is used to check if we are building in a separate output directory,
1902 # 1) Check that make has not been executed in the kernel src $(srctree)
1903 prepare3
: include/config
/uboot.release
1904 ifneq ($(KBUILD_SRC
),)
1905 @
$(kecho
) ' Using $(srctree) as source for U-Boot'
1906 $(Q
)if
[ -f
$(srctree
)/.config
-o
-d
$(srctree
)/include/config
]; then \
1907 echo
>&2 " $(srctree) is not clean, please run 'make mrproper'"; \
1908 echo
>&2 " in the '$(srctree)' directory.";\
1913 # prepare2 creates a makefile if using a separate output directory
1914 prepare2
: prepare3 outputmakefile cfg
1916 prepare1
: prepare2
$(version_h
) $(timestamp_h
) $(dt_h
) $(env_h
) \
1917 include/config
/auto.conf
1918 ifeq ($(wildcard $(LDSCRIPT
)),)
1919 @echo
>&2 " Could not find linker script."
1923 ifeq ($(CONFIG_USE_DEFAULT_ENV_FILE
),y
)
1924 prepare1
: $(defaultenv_h
)
1926 envtools
: $(defaultenv_h
)
1929 archprepare
: prepare1 scripts_basic
1931 prepare0
: archprepare FORCE
1932 $(Q
)$(MAKE
) $(build
)=.
1934 # All the preparing..
1937 # Generate some files
1938 # ---------------------------------------------------------------------------
1940 # Use sed to remove leading zeros from PATCHLEVEL to avoid using octal numbers
1941 define filechk_version.h
1942 (echo \
#define PLAIN_VERSION \"$(UBOOTRELEASE)\"; \
1943 echo \
#define U_BOOT_VERSION \"U-Boot \" PLAIN_VERSION; \
1944 echo \
#define U_BOOT_VERSION_NUM $(VERSION); \
1945 echo \
#define U_BOOT_VERSION_NUM_PATCH $$(echo $(PATCHLEVEL) | \
1946 sed
-e
"s/^0*//"); \
1947 echo \
#define CC_VERSION_STRING \"$$(LC_ALL=C $(CC) --version | head -n 1)\"; \
1948 echo \
#define LD_VERSION_STRING \"$$(LC_ALL=C $(LD) --version | head -n 1)\"; )
1951 # The SOURCE_DATE_EPOCH mechanism requires a date that behaves like GNU date.
1952 # The BSD date on the other hand behaves different and would produce errors
1953 # with the misused '-d' switch. Respect that and search a working date with
1954 # well known pre- and suffixes for the GNU variant of date.
1955 define filechk_timestamp.h
1956 (if
test -n
"$${SOURCE_DATE_EPOCH}"; then \
1957 SOURCE_DATE
="@$${SOURCE_DATE_EPOCH}"; \
1959 for date in gdate date.gnu date
; do \
1960 $${date} -u
-d
"$${SOURCE_DATE}" >/dev
/null
2>&1 && DATE
="$${date}"; \
1962 if
test -n
"$${DATE}"; then \
1963 LC_ALL
=C
$${DATE} -u
-d
"$${SOURCE_DATE}" +'#define U_BOOT_DATE "%b %d %C%y"'; \
1964 LC_ALL
=C
$${DATE} -u
-d
"$${SOURCE_DATE}" +'#define U_BOOT_TIME "%T"'; \
1965 LC_ALL
=C
$${DATE} -u
-d
"$${SOURCE_DATE}" +'#define U_BOOT_TZ "%z"'; \
1966 LC_ALL
=C
$${DATE} -u
-d
"$${SOURCE_DATE}" +'#define U_BOOT_EPOCH %s'; \
1971 LC_ALL
=C date
+'#define U_BOOT_DATE "%b %d %C%y"'; \
1972 LC_ALL
=C date
+'#define U_BOOT_TIME "%T"'; \
1973 LC_ALL
=C date
+'#define U_BOOT_TZ "%z"'; \
1974 LC_ALL
=C date
+'#define U_BOOT_EPOCH %s'; \
1978 define filechk_defaultenv.h
1979 ( { grep
-v
'^#' | grep
-v
'^$$' || true
; echo
'' ; } | \
1981 sed
-e
's/\\\x0\s*//g' | \
1986 (if
test -n
"$${DEVICE_TREE}"; then \
1987 echo \
#define DEVICE_TREE \"$(DEVICE_TREE)\"; \
1989 echo \
#define DEVICE_TREE CONFIG_DEFAULT_DEVICE_TREE; \
1993 $(version_h
): include/config
/uboot.release FORCE
1994 $(call filechk
,version.h
)
1996 $(timestamp_h
): $(srctree
)/Makefile FORCE
1997 $(call filechk
,timestamp.h
)
1999 $(dt_h
): $(srctree
)/Makefile FORCE
2000 $(call filechk
,dt.h
)
2002 $(defaultenv_h
): $(CONFIG_DEFAULT_ENV_FILE
:"%"=%) FORCE
2003 $(call filechk
,defaultenv.h
)
2005 # ---------------------------------------------------------------------------
2008 ifneq ($(wildcard $(srctree
)/arch
/$(SRCARCH
)/boot
/dts
/),)
2009 dtstree
:= arch
/$(SRCARCH
)/boot
/dts
2014 %.dtb
: prepare3 scripts_dtc
2015 $(Q
)$(MAKE
) $(build
)=$(dtstree
) $(dtstree
)/$@
2017 PHONY
+= dtbs dtbs_install
2018 dtbs
: prepare3 scripts_dtc
2019 $(Q
)$(MAKE
) $(build
)=$(dtstree
)
2022 $(Q
)$(MAKE
) $(dtbinst
)=$(dtstree
)
2024 ifdef CONFIG_OF_EARLY_FLATTREE
2030 # Check dtc and pylibfdt, if DTC is provided, else build them
2031 PHONY
+= scripts_dtc
2032 scripts_dtc
: scripts_basic
2033 $(Q
)if
test "$(DTC)" = "$(DTC_INTREE)"; then \
2034 $(MAKE
) $(build
)=scripts
/dtc
; \
2036 if
! $(DTC
) -v
>/dev
/null
; then \
2037 echo
'*** Failed to check dtc version: $(DTC)'; \
2040 if
test "$(call dtc-version)" -lt
$(DTC_MIN_VERSION
); then \
2041 echo
'*** Your dtc is too old, please upgrade to dtc $(DTC_MIN_VERSION) or newer'; \
2044 if
[ -n
"$(CONFIG_PYLIBFDT)" ]; then \
2045 if
! echo
"import libfdt" |
$(PYTHON3
) 2>/dev
/null
; then \
2046 echo
'*** pylibfdt does not seem to be available with $(PYTHON3)'; \
2054 # ---------------------------------------------------------------------------
2055 quiet_cmd_cpp_lds
= LDS
$@
2056 cmd_cpp_lds
= $(CPP
) -Wp
,-MD
,$(depfile
) $(cpp_flags
) $(LDPPFLAGS
) \
2057 -D__ASSEMBLY__
-x assembler-with-cpp
-std
=c99
-P
-o
$@
$<
2059 u-boot.lds
: $(LDSCRIPT
) prepare FORCE
2060 $(call if_changed_dep
,cpp_lds
)
2062 spl
/u-boot-spl.bin
: spl
/u-boot-spl
2066 spl
/u-boot-spl-dtb.bin
: spl
/u-boot-spl
2069 spl
/u-boot-spl-dtb.hex
: spl
/u-boot-spl
2072 spl
/u-boot-spl
: tools prepare \
2073 $(if
$(CONFIG_OF_SEPARATE
)$(CONFIG_OF_EMBED
)$(CONFIG_SPL_OF_PLATDATA
),dts
/dt.dtb
) \
2074 $(if
$(CONFIG_OF_SEPARATE
)$(CONFIG_OF_EMBED
)$(CONFIG_TPL_OF_PLATDATA
),dts
/dt.dtb
)
2075 $(Q
)$(MAKE
) obj
=spl
-f
$(srctree
)/scripts
/Makefile.spl
all
2077 spl
/sunxi-spl.bin
: spl
/u-boot-spl
2080 spl
/sunxi-spl-with-ecc.bin
: spl
/sunxi-spl.bin
2083 spl
/u-boot-spl.sfp
: spl
/u-boot-spl
2086 spl
/boot.bin
: spl
/u-boot-spl
2089 tpl
/u-boot-tpl.bin
: tools prepare \
2090 $(if
$(CONFIG_OF_SEPARATE
)$(CONFIG_OF_EMBED
)$(CONFIG_SPL_OF_PLATDATA
),dts
/dt.dtb
)
2091 $(Q
)$(MAKE
) obj
=tpl
-f
$(srctree
)/scripts
/Makefile.spl
all
2094 TAG_SUBDIRS
:= $(patsubst %,$(srctree
)/%,$(u-boot-dirs
) include)
2100 ctags
-w
-o ctags
`$(FIND) $(FINDFLAGS) $(TAG_SUBDIRS) \
2101 -name '*.[chS]' -print`
2105 etags
-a
-o etags
`$(FIND) $(FINDFLAGS) $(TAG_SUBDIRS) \
2106 -name '*.[chS]' -print`
2108 $(FIND
) $(FINDFLAGS
) $(TAG_SUBDIRS
) -name
'*.[chS]' -print > \
2110 @find
$(TAG_SUBDIRS
) -name
'*.[chS]' -type l
-print | \
2111 grep
-xvf
- cscope.files
> cscope.files.no-symlinks
; \
2112 mv cscope.files.no-symlinks cscope.files
2117 grep
-v
'\(compiled\)\|\(\.o$$\)\|\( [aUw] \)\|\(\.\.ng$$\)\|\(LASH[RL]DI\)' | \
2120 @
$(call SYSTEM_MAP
,$<) > $@
2122 #########################################################################
2124 # ARM relocations should all be R_ARM_RELATIVE (32-bit) or
2125 # R_AARCH64_RELATIVE (64-bit).
2126 checkarmreloc
: u-boot
2127 @RELOC
="`$(CROSS_COMPILE)readelf -r -W $< | cut -d ' ' -f 4 | \
2128 grep R_A | sort -u`"; \
2129 if
test "$$RELOC" != "R_ARM_RELATIVE" -a \
2130 "$$RELOC" != "R_AARCH64_RELATIVE"; then \
2131 echo
"$< contains unexpected relocations: $$RELOC"; \
2135 tools
/version.h
: include/version.h
2136 $(Q
)mkdir
-p
$(dir $@
)
2137 $(call if_changed
,copy
)
2139 envtools
: scripts_basic
$(version_h
) $(timestamp_h
) tools
/version.h
2140 $(Q
)$(MAKE
) $(build
)=tools
/env
2142 tools-only
: export TOOLS_ONLY
=y
2143 tools-only
: scripts_basic
$(version_h
) $(timestamp_h
) tools
/version.h
2144 $(Q
)$(MAKE
) $(build
)=tools
2146 tools-all
: export HOST_TOOLS_ALL
=y
2147 tools-all
: envtools tools
;
2149 cross_tools
: export CROSS_BUILD_TOOLS
=y
2150 cross_tools
: tools
;
2154 git log
--no-merges U-Boot-1_1_5.. | \
2155 unexpand
-a | sed
-e
's/\s\s*$$//' > $@
2157 #########################################################################
2160 # Cleaning is done on three levels.
2161 # make clean Delete most generated files
2162 # Leave enough to build external modules
2163 # make mrproper Delete the current configuration, and all generated files
2164 # make distclean Remove editor backup files, patch leftover files and the like
2166 # Directories & files removed with 'make clean'
2167 CLEAN_DIRS
+= $(MODVERDIR
) \
2168 $(foreach d
, spl tpl
, $(patsubst %,$d/%, \
2169 $(filter-out include, $(shell ls
-1 $d 2>/dev
/null
))))
2171 CLEAN_FILES
+= include/bmp_logo.h
include/bmp_logo_data.h tools
/version.h \
2172 u-boot
* MLO
* SPL System.map fit-dtb.blob
* \
2173 u-boot-ivt.img.log u-boot-dtb.imx.log SPL.log u-boot.imx.log \
2174 lpc32xx-
* bl31.c bl31.elf bl31_
*.bin image.map tispl.bin
* \
2175 idbloader.img flash.bin flash.log defconfig keep-syms-lto.c
2177 # Directories & files removed with 'make mrproper'
2178 MRPROPER_DIRS
+= include/config
include/generated spl tpl \
2179 .tmp_objdiff doc
/output
include/asm
2181 # Remove include/asm symlink created by U-Boot before v2014.01
2182 MRPROPER_FILES
+= .config .config.old
include/autoconf.mk
* include/config.h \
2183 ctags etags
tags TAGS cscope
* GPATH GTAGS GRTAGS GSYMS \
2184 drivers
/video
/fonts
/*.S
include/asm
2186 # clean - Delete most, but leave enough to build external modules
2188 clean: rm-dirs
:= $(CLEAN_DIRS
)
2189 clean: rm-files
:= $(CLEAN_FILES
)
2191 clean-dirs
:= $(foreach f
,$(u-boot-alldirs
),$(if
$(wildcard $(srctree
)/$f/Makefile
),$f))
2193 clean-dirs
:= $(addprefix _clean_
, $(clean-dirs
))
2195 PHONY
+= $(clean-dirs
) clean archclean
2197 $(Q
)$(MAKE
) $(clean)=$(patsubst _clean_
%,%,$@
)
2199 clean: $(clean-dirs
)
2202 @find
$(if
$(KBUILD_EXTMOD
), $(KBUILD_EXTMOD
), .
) $(RCS_FIND_IGNORE
) \
2203 \
( -name
'*.[oas]' -o
-name
'*.ko' -o
-name
'.*.cmd' \
2204 -o
-name
'*.ko.*' -o
-name
'*.su' -o
-name
'*.pyc' \
2205 -o
-name
'.*.d' -o
-name
'.*.tmp' -o
-name
'*.mod.c' \
2206 -o
-name
'*.lex.c' -o
-name
'*.tab.[ch]' \
2207 -o
-name
'*.asn1.[ch]' \
2208 -o
-name
'*.symtypes' -o
-name
'modules.order' \
2209 -o
-name modules.builtin
-o
-name
'.tmp_*.o.*' \
2210 -o
-name
'dsdt.aml' -o
-name
'dsdt.asl.tmp' -o
-name
'dsdt.c' \
2211 -o
-name
'*.efi' -o
-name
'*.gcno' -o
-name
'*.so' \
) \
2212 -type f
-print | xargs
rm -f
2214 # mrproper - Delete all generated files, including .config
2216 mrproper
: rm-dirs
:= $(wildcard $(MRPROPER_DIRS
))
2217 mrproper
: rm-files
:= $(wildcard $(MRPROPER_FILES
))
2218 mrproper-dirs
:= $(addprefix _mrproper_
,scripts
)
2220 PHONY
+= $(mrproper-dirs
) mrproper archmrproper
2222 $(Q
)$(MAKE
) $(clean)=$(patsubst _mrproper_
%,%,$@
)
2224 mrproper
: clean $(mrproper-dirs
)
2227 @
rm -f arch
/*/include/asm
/arch
2234 @find
$(srctree
) $(RCS_FIND_IGNORE
) \
2235 \
( -name
'*.orig' -o
-name
'*.rej' -o
-name
'*~' \
2236 -o
-name
'*.bak' -o
-name
'#*#' -o
-name
'.*.orig' \
2237 -o
-name
'.*.rej' -o
-name
'*%' -o
-name
'core' \
2238 -o
-name
'*.pyc' \
) \
2239 -type f
-print | xargs
rm -f
2240 @
rm -f boards.cfg CHANGELOG
2243 F
=`basename $(srctree)` ; cd ..
; \
2244 gtar
--force-local
-zcvf
`LC_ALL=C date "+$$F-%Y-%m-%d-%T.tar.gz"` $$F
2247 @echo
'Cleaning targets:'
2248 @echo
' clean - Remove most generated files but keep the config'
2249 @echo
' mrproper - Remove all generated files + config + various backup files'
2250 @echo
' distclean - mrproper + remove editor backup and patch files'
2252 @echo
'Configuration targets:'
2253 @
$(MAKE
) -f
$(srctree
)/scripts
/kconfig
/Makefile help
2255 @echo
'Test targets:'
2257 @echo
' check - Run all automated tests that use sandbox'
2258 @echo
' qcheck - Run quick automated tests that use sandbox'
2259 @echo
' tcheck - Run quick automated tests on tools'
2261 @echo
'Other generic targets:'
2262 @echo
' all - Build all necessary images depending on configuration'
2263 @echo
' tests - Build U-Boot for sandbox and run tests'
2264 @echo
'* u-boot - Build the bare u-boot'
2265 @echo
' dir/ - Build all files in dir and below'
2266 @echo
' dir/file.[oisS] - Build specified target only'
2267 @echo
' dir/file.lst - Build specified mixed source/assembly target only'
2268 @echo
' (requires a recent binutils and recent build (System.map))'
2269 @echo
' tags/ctags - Generate ctags file for editors'
2270 @echo
' etags - Generate etags file for editors'
2271 @echo
' cscope - Generate cscope index'
2272 @echo
' ubootrelease - Output the release version string (use with make -s)'
2273 @echo
' ubootversion - Output the version stored in Makefile (use with make -s)'
2274 @echo
" cfg - Don't build, just create the .cfg files"
2275 @echo
" envtools - Build only the target-side environment tools"
2277 @echo
'Static analysers'
2278 @echo
' checkstack - Generate a list of stack hogs'
2279 @echo
' coccicheck - Execute static code analysis with Coccinelle'
2281 @echo
'Documentation targets:'
2282 @
$(MAKE
) -f
$(srctree
)/doc
/Makefile dochelp
2284 @echo
' make V=0|1 [targets] 0 => quiet build (default), 1 => verbose build'
2285 @echo
' make V=2 [targets] 2 => give reason for rebuild of target'
2286 @echo
' make O=dir [targets] Locate all output files in "dir", including .config'
2287 @echo
' make C=1 [targets] Check all c source with $$CHECK (sparse by default)'
2288 @echo
' make C=2 [targets] Force check of all c source with $$CHECK'
2289 @echo
' make RECORDMCOUNT_WARN=1 [targets] Warn about ignored mcount sections'
2290 @echo
' make W=n [targets] Enable extra gcc checks, n=1,2,3 where'
2291 @echo
' 1: warnings which may be relevant and do not occur too often'
2292 @echo
' 2: warnings which occur quite often but may still be relevant'
2293 @echo
' 3: more obscure warnings, can most likely be ignored'
2294 @echo
' Multiple levels can be combined with W=12 or W=123'
2296 @echo
'Execute "make" or "make all" to build all targets marked with [*] '
2297 @echo
'For further info see the ./README file'
2303 $(srctree
)/test/run quick
2306 $(srctree
)/test/run tools
2308 # Documentation targets
2309 # ---------------------------------------------------------------------------
2310 DOC_TARGETS
:= xmldocs latexdocs pdfdocs htmldocs epubdocs cleandocs \
2311 linkcheckdocs dochelp refcheckdocs
2312 PHONY
+= $(DOC_TARGETS
)
2313 $(DOC_TARGETS
): scripts_basic FORCE
2314 $(Q
)$(MAKE
) $(build
)=doc
$@
2316 PHONY
+= checkstack ubootrelease ubootversion
2319 $(OBJDUMP
) -d u-boot
$$(find .
-name u-boot-spl
) | \
2320 $(PERL
) $(src
)/scripts
/checkstack.pl
$(ARCH
)
2323 @echo
"$(UBOOTVERSION)$$($(CONFIG_SHELL) $(srctree)/scripts/setlocalversion $(srctree))"
2326 @echo
$(UBOOTVERSION
)
2329 # ---------------------------------------------------------------------------
2330 # Single targets are compatible with:
2331 # - build with mixed source and output
2332 # - build with separate output dir 'make O=...'
2333 # - external modules
2335 # target-dir => where to store outputfile
2336 # build-dir => directory in kernel source tree to use
2338 ifeq ($(KBUILD_EXTMOD
),)
2339 build-dir
= $(patsubst %/,%,$(dir $@
))
2340 target-dir
= $(dir $@
)
2342 zap-slash
=$(filter-out .
,$(patsubst %/,%,$(dir $@
)))
2343 build-dir
= $(KBUILD_EXTMOD
)$(if
$(zap-slash
),/$(zap-slash
))
2344 target-dir
= $(if
$(KBUILD_EXTMOD
),$(dir $<),$(dir $@
))
2347 %.s
: %.c prepare scripts FORCE
2348 $(Q
)$(MAKE
) $(build
)=$(build-dir
) $(target-dir
)$(notdir $@
)
2349 %.i
: %.c prepare scripts FORCE
2350 $(Q
)$(MAKE
) $(build
)=$(build-dir
) $(target-dir
)$(notdir $@
)
2351 %.o
: %.c prepare scripts FORCE
2352 $(Q
)$(MAKE
) $(build
)=$(build-dir
) $(target-dir
)$(notdir $@
)
2353 %.lst
: %.c prepare scripts FORCE
2354 $(Q
)$(MAKE
) $(build
)=$(build-dir
) $(target-dir
)$(notdir $@
)
2355 %.s
: %.S prepare scripts FORCE
2356 $(Q
)$(MAKE
) $(build
)=$(build-dir
) $(target-dir
)$(notdir $@
)
2357 %.o
: %.S prepare scripts FORCE
2358 $(Q
)$(MAKE
) $(build
)=$(build-dir
) $(target-dir
)$(notdir $@
)
2359 %.symtypes
: %.c prepare scripts FORCE
2360 $(Q
)$(MAKE
) $(build
)=$(build-dir
) $(target-dir
)$(notdir $@
)
2363 /: prepare scripts FORCE
2365 $(Q
)$(MAKE
) KBUILD_MODULES
=$(if
$(CONFIG_MODULES
),1) \
2366 $(build
)=$(build-dir
)
2367 %/: prepare scripts FORCE
2369 $(Q
)$(MAKE
) KBUILD_MODULES
=$(if
$(CONFIG_MODULES
),1) \
2370 $(build
)=$(build-dir
)
2371 %.ko
: prepare scripts FORCE
2373 $(Q
)$(MAKE
) KBUILD_MODULES
=$(if
$(CONFIG_MODULES
),1) \
2374 $(build
)=$(build-dir
) $(@
:.ko
=.o
)
2375 $(Q
)$(MAKE
) -f
$(srctree
)/scripts
/Makefile.modpost
2377 quiet_cmd_genenv
= GENENV
$@
2378 cmd_genenv
= $(OBJCOPY
) --dump-section .rodata.default_environment
=$@ env
/common.o
; \
2379 sed
--in-place
-e
's/\x00/\x0A/g' $@
2381 u-boot-initial-env
: u-boot.bin
2382 $(call if_changed
,genenv
)
2384 # Consistency checks
2385 # ---------------------------------------------------------------------------
2390 $(Q
)$(CONFIG_SHELL
) $(srctree
)/scripts
/$@
2392 # FIXME Should go into a make.lib or something
2393 # ===========================================================================
2395 quiet_cmd_rmdirs
= $(if
$(wildcard $(rm-dirs
)),CLEAN
$(wildcard $(rm-dirs
)))
2396 cmd_rmdirs
= rm -rf
$(rm-dirs
)
2398 quiet_cmd_rmfiles
= $(if
$(wildcard $(rm-files
)),CLEAN
$(wildcard $(rm-files
)))
2399 cmd_rmfiles
= rm -f
$(rm-files
)
2401 # read all saved command lines
2403 cmd_files
:= $(wildcard .
*.cmd
)
2405 ifneq ($(cmd_files
),)
2406 $(cmd_files
): ; # Do not try to update included dependency files
2407 include $(cmd_files
)
2410 endif #ifeq ($(config-targets),1)
2411 endif #ifeq ($(mixed-targets),1)
2412 endif # skip-makefile
2417 # Declare the contents of the PHONY variable as phony. We keep that
2418 # information in a variable so we can use it in if_changed and friends.