2 # (C) Copyright 2000 - 2013
3 # Wolfgang Denk, DENX Software Engineering, wd@denx.de.
5 # SPDX-License-Identifier: GPL-2.0+
11 This directory contains the source code for U-Boot, a boot loader for
12 Embedded boards based on PowerPC, ARM, MIPS and several other
13 processors, which can be installed in a boot ROM and used to
14 initialize and test the hardware or to download and run application
17 The development of U-Boot is closely related to Linux: some parts of
18 the source code originate in the Linux source tree, we have some
19 header files in common, and special provision has been made to
20 support booting of Linux images.
22 Some attention has been paid to make this software easily
23 configurable and extendable. For instance, all monitor commands are
24 implemented with the same call interface, so that it's very easy to
25 add new commands. Also, instead of permanently adding rarely used
26 code (for instance hardware test utilities) to the monitor, you can
27 load and run it dynamically.
33 In general, all boards for which a configuration option exists in the
34 Makefile have been tested to some extent and can be considered
35 "working". In fact, many of them are used in production systems.
37 In case of problems see the CHANGELOG and CREDITS files to find out
38 who contributed the specific port. The boards.cfg file lists board
41 Note: There is no CHANGELOG file in the actual U-Boot source tree;
42 it can be created dynamically from the Git log using:
50 In case you have questions about, problems with or contributions for
51 U-Boot you should send a message to the U-Boot mailing list at
52 <u-boot@lists.denx.de>. There is also an archive of previous traffic
53 on the mailing list - please search the archive before asking FAQ's.
54 Please see http://lists.denx.de/pipermail/u-boot and
55 http://dir.gmane.org/gmane.comp.boot-loaders.u-boot
58 Where to get source code:
59 =========================
61 The U-Boot source code is maintained in the git repository at
62 git://www.denx.de/git/u-boot.git ; you can browse it online at
63 http://www.denx.de/cgi-bin/gitweb.cgi?p=u-boot.git;a=summary
65 The "snapshot" links on this page allow you to download tarballs of
66 any version you might be interested in. Official releases are also
67 available for FTP download from the ftp://ftp.denx.de/pub/u-boot/
70 Pre-built (and tested) images are available from
71 ftp://ftp.denx.de/pub/u-boot/images/
77 - start from 8xxrom sources
78 - create PPCBoot project (http://sourceforge.net/projects/ppcboot)
80 - make it easier to add custom boards
81 - make it possible to add other [PowerPC] CPUs
82 - extend functions, especially:
83 * Provide extended interface to Linux boot loader
86 * PCMCIA / CompactFlash / ATA disk / SCSI ... boot
87 - create ARMBoot project (http://sourceforge.net/projects/armboot)
88 - add other CPU families (starting with ARM)
89 - create U-Boot project (http://sourceforge.net/projects/u-boot)
90 - current project page: see http://www.denx.de/wiki/U-Boot
96 The "official" name of this project is "Das U-Boot". The spelling
97 "U-Boot" shall be used in all written text (documentation, comments
98 in source files etc.). Example:
100 This is the README file for the U-Boot project.
102 File names etc. shall be based on the string "u-boot". Examples:
104 include/asm-ppc/u-boot.h
106 #include <asm/u-boot.h>
108 Variable names, preprocessor constants etc. shall be either based on
109 the string "u_boot" or on "U_BOOT". Example:
111 U_BOOT_VERSION u_boot_logo
112 IH_OS_U_BOOT u_boot_hush_start
118 Starting with the release in October 2008, the names of the releases
119 were changed from numerical release numbers without deeper meaning
120 into a time stamp based numbering. Regular releases are identified by
121 names consisting of the calendar year and month of the release date.
122 Additional fields (if present) indicate release candidates or bug fix
123 releases in "stable" maintenance trees.
126 U-Boot v2009.11 - Release November 2009
127 U-Boot v2009.11.1 - Release 1 in version November 2009 stable tree
128 U-Boot v2010.09-rc1 - Release candiate 1 for September 2010 release
134 /arch Architecture specific files
135 /arc Files generic to ARC architecture
136 /cpu CPU specific files
137 /arc700 Files specific to ARC 700 CPUs
138 /lib Architecture specific library files
139 /arm Files generic to ARM architecture
140 /cpu CPU specific files
141 /arm720t Files specific to ARM 720 CPUs
142 /arm920t Files specific to ARM 920 CPUs
143 /at91 Files specific to Atmel AT91RM9200 CPU
144 /imx Files specific to Freescale MC9328 i.MX CPUs
145 /s3c24x0 Files specific to Samsung S3C24X0 CPUs
146 /arm926ejs Files specific to ARM 926 CPUs
147 /arm1136 Files specific to ARM 1136 CPUs
148 /pxa Files specific to Intel XScale PXA CPUs
149 /sa1100 Files specific to Intel StrongARM SA1100 CPUs
150 /lib Architecture specific library files
151 /avr32 Files generic to AVR32 architecture
152 /cpu CPU specific files
153 /lib Architecture specific library files
154 /blackfin Files generic to Analog Devices Blackfin architecture
155 /cpu CPU specific files
156 /lib Architecture specific library files
157 /m68k Files generic to m68k architecture
158 /cpu CPU specific files
159 /mcf52x2 Files specific to Freescale ColdFire MCF52x2 CPUs
160 /mcf5227x Files specific to Freescale ColdFire MCF5227x CPUs
161 /mcf532x Files specific to Freescale ColdFire MCF5329 CPUs
162 /mcf5445x Files specific to Freescale ColdFire MCF5445x CPUs
163 /mcf547x_8x Files specific to Freescale ColdFire MCF547x_8x CPUs
164 /lib Architecture specific library files
165 /microblaze Files generic to microblaze architecture
166 /cpu CPU specific files
167 /lib Architecture specific library files
168 /mips Files generic to MIPS architecture
169 /cpu CPU specific files
170 /mips32 Files specific to MIPS32 CPUs
171 /mips64 Files specific to MIPS64 CPUs
172 /lib Architecture specific library files
173 /nds32 Files generic to NDS32 architecture
174 /cpu CPU specific files
175 /n1213 Files specific to Andes Technology N1213 CPUs
176 /lib Architecture specific library files
177 /nios2 Files generic to Altera NIOS2 architecture
178 /cpu CPU specific files
179 /lib Architecture specific library files
180 /openrisc Files generic to OpenRISC architecture
181 /cpu CPU specific files
182 /lib Architecture specific library files
183 /powerpc Files generic to PowerPC architecture
184 /cpu CPU specific files
185 /mpc5xx Files specific to Freescale MPC5xx CPUs
186 /mpc5xxx Files specific to Freescale MPC5xxx CPUs
187 /mpc8xx Files specific to Freescale MPC8xx CPUs
188 /mpc8260 Files specific to Freescale MPC8260 CPUs
189 /mpc85xx Files specific to Freescale MPC85xx CPUs
190 /ppc4xx Files specific to AMCC PowerPC 4xx CPUs
191 /lib Architecture specific library files
192 /sh Files generic to SH architecture
193 /cpu CPU specific files
194 /sh2 Files specific to sh2 CPUs
195 /sh3 Files specific to sh3 CPUs
196 /sh4 Files specific to sh4 CPUs
197 /lib Architecture specific library files
198 /sparc Files generic to SPARC architecture
199 /cpu CPU specific files
200 /leon2 Files specific to Gaisler LEON2 SPARC CPU
201 /leon3 Files specific to Gaisler LEON3 SPARC CPU
202 /lib Architecture specific library files
203 /x86 Files generic to x86 architecture
204 /cpu CPU specific files
205 /lib Architecture specific library files
206 /api Machine/arch independent API for external apps
207 /board Board dependent files
208 /common Misc architecture independent functions
209 /disk Code for disk drive partition handling
210 /doc Documentation (don't expect too much)
211 /drivers Commonly used device drivers
212 /dts Contains Makefile for building internal U-Boot fdt.
213 /examples Example code for standalone applications, etc.
214 /fs Filesystem code (cramfs, ext2, jffs2, etc.)
215 /include Header Files
216 /lib Files generic to all architectures
217 /libfdt Library files to support flattened device trees
218 /lzma Library files to support LZMA decompression
219 /lzo Library files to support LZO decompression
221 /post Power On Self Test
222 /spl Secondary Program Loader framework
223 /tools Tools to build S-Record or U-Boot images, etc.
225 Software Configuration:
226 =======================
228 Configuration is usually done using C preprocessor defines; the
229 rationale behind that is to avoid dead code whenever possible.
231 There are two classes of configuration variables:
233 * Configuration _OPTIONS_:
234 These are selectable by the user and have names beginning with
237 * Configuration _SETTINGS_:
238 These depend on the hardware etc. and should not be meddled with if
239 you don't know what you're doing; they have names beginning with
242 Later we will add a configuration tool - probably similar to or even
243 identical to what's used for the Linux kernel. Right now, we have to
244 do the configuration by hand, which means creating some symbolic
245 links and editing some configuration files. We use the TQM8xxL boards
249 Selection of Processor Architecture and Board Type:
250 ---------------------------------------------------
252 For all supported boards there are ready-to-use default
253 configurations available; just type "make <board_name>_defconfig".
255 Example: For a TQM823L module type:
258 make TQM823L_defconfig
260 For the Cogent platform, you need to specify the CPU type as well;
261 e.g. "make cogent_mpc8xx_defconfig". And also configure the cogent
262 directory according to the instructions in cogent/README.
268 U-Boot can be built natively to run on a Linux host using the 'sandbox'
269 board. This allows feature development which is not board- or architecture-
270 specific to be undertaken on a native platform. The sandbox is also used to
271 run some of U-Boot's tests.
273 See board/sandbox/README.sandbox for more details.
276 Board Initialisation Flow:
277 --------------------------
279 This is the intended start-up flow for boards. This should apply for both
280 SPL and U-Boot proper (i.e. they both follow the same rules). At present SPL
281 mostly uses a separate code path, but the funtion names and roles of each
282 function are the same. Some boards or architectures may not conform to this.
283 At least most ARM boards which use CONFIG_SPL_FRAMEWORK conform to this.
285 Execution starts with start.S with three functions called during init after
286 that. The purpose and limitations of each is described below.
289 - purpose: essential init to permit execution to reach board_init_f()
290 - no global_data or BSS
291 - there is no stack (ARMv7 may have one but it will soon be removed)
292 - must not set up SDRAM or use console
293 - must only do the bare minimum to allow execution to continue to
295 - this is almost never needed
296 - return normally from this function
299 - purpose: set up the machine ready for running board_init_r():
300 i.e. SDRAM and serial UART
301 - global_data is available
303 - BSS is not available, so you cannot use global/static variables,
304 only stack variables and global_data
306 Non-SPL-specific notes:
307 - dram_init() is called to set up DRAM. If already done in SPL this
311 - you can override the entire board_init_f() function with your own
313 - preloader_console_init() can be called here in extremis
314 - should set up SDRAM, and anything needed to make the UART work
315 - these is no need to clear BSS, it will be done by crt0.S
316 - must return normally from this function (don't call board_init_r()
319 Here the BSS is cleared. For SPL, if CONFIG_SPL_STACK_R is defined, then at
320 this point the stack and global_data are relocated to below
321 CONFIG_SPL_STACK_R_ADDR. For non-SPL, U-Boot is relocated to run at the top of
325 - purpose: main execution, common code
326 - global_data is available
328 - BSS is available, all static/global variables can be used
329 - execution eventually continues to main_loop()
331 Non-SPL-specific notes:
332 - U-Boot is relocated to the top of memory and is now running from
336 - stack is optionally in SDRAM, if CONFIG_SPL_STACK_R is defined and
337 CONFIG_SPL_STACK_R_ADDR points into SDRAM
338 - preloader_console_init() can be called here - typically this is
339 done by defining CONFIG_SPL_BOARD_INIT and then supplying a
340 spl_board_init() function containing this call
341 - loads U-Boot or (in falcon mode) Linux
345 Configuration Options:
346 ----------------------
348 Configuration depends on the combination of board and CPU type; all
349 such information is kept in a configuration file
350 "include/configs/<board_name>.h".
352 Example: For a TQM823L module, all configuration settings are in
353 "include/configs/TQM823L.h".
356 Many of the options are named exactly as the corresponding Linux
357 kernel configuration options. The intention is to make it easier to
358 build a config tool - later.
361 The following options need to be configured:
363 - CPU Type: Define exactly one, e.g. CONFIG_MPC85XX.
365 - Board Type: Define exactly one, e.g. CONFIG_MPC8540ADS.
367 - CPU Daughterboard Type: (if CONFIG_ATSTK1000 is defined)
368 Define exactly one, e.g. CONFIG_ATSTK1002
370 - CPU Module Type: (if CONFIG_COGENT is defined)
371 Define exactly one of
373 --- FIXME --- not tested yet:
374 CONFIG_CMA286_60, CONFIG_CMA286_21, CONFIG_CMA286_60P,
375 CONFIG_CMA287_23, CONFIG_CMA287_50
377 - Motherboard Type: (if CONFIG_COGENT is defined)
378 Define exactly one of
379 CONFIG_CMA101, CONFIG_CMA102
381 - Motherboard I/O Modules: (if CONFIG_COGENT is defined)
382 Define one or more of
385 - Motherboard Options: (if CONFIG_CMA101 or CONFIG_CMA102 are defined)
386 Define one or more of
387 CONFIG_LCD_HEARTBEAT - update a character position on
388 the LCD display every second with
391 - Marvell Family Member
392 CONFIG_SYS_MVFS - define it if you want to enable
393 multiple fs option at one time
394 for marvell soc family
396 - 8xx CPU Options: (if using an MPC8xx CPU)
397 CONFIG_8xx_GCLK_FREQ - deprecated: CPU clock if
398 get_gclk_freq() cannot work
399 e.g. if there is no 32KHz
400 reference PIT/RTC clock
401 CONFIG_8xx_OSCLK - PLL input clock (either EXTCLK
404 - 859/866/885 CPU options: (if using a MPC859 or MPC866 or MPC885 CPU):
405 CONFIG_SYS_8xx_CPUCLK_MIN
406 CONFIG_SYS_8xx_CPUCLK_MAX
407 CONFIG_8xx_CPUCLK_DEFAULT
408 See doc/README.MPC866
410 CONFIG_SYS_MEASURE_CPUCLK
412 Define this to measure the actual CPU clock instead
413 of relying on the correctness of the configured
414 values. Mostly useful for board bringup to make sure
415 the PLL is locked at the intended frequency. Note
416 that this requires a (stable) reference clock (32 kHz
417 RTC clock or CONFIG_SYS_8XX_XIN)
419 CONFIG_SYS_DELAYED_ICACHE
421 Define this option if you want to enable the
422 ICache only when Code runs from RAM.
427 Specifies that the core is a 64-bit PowerPC implementation (implements
428 the "64" category of the Power ISA). This is necessary for ePAPR
429 compliance, among other possible reasons.
431 CONFIG_SYS_FSL_TBCLK_DIV
433 Defines the core time base clock divider ratio compared to the
434 system clock. On most PQ3 devices this is 8, on newer QorIQ
435 devices it can be 16 or 32. The ratio varies from SoC to Soc.
437 CONFIG_SYS_FSL_PCIE_COMPAT
439 Defines the string to utilize when trying to match PCIe device
440 tree nodes for the given platform.
442 CONFIG_SYS_PPC_E500_DEBUG_TLB
444 Enables a temporary TLB entry to be used during boot to work
445 around limitations in e500v1 and e500v2 external debugger
446 support. This reduces the portions of the boot code where
447 breakpoints and single stepping do not work. The value of this
448 symbol should be set to the TLB1 entry to be used for this
451 CONFIG_SYS_FSL_ERRATUM_A004510
453 Enables a workaround for erratum A004510. If set,
454 then CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV and
455 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY must be set.
457 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV
458 CONFIG_SYS_FSL_ERRATUM_A004510_SVR_REV2 (optional)
460 Defines one or two SoC revisions (low 8 bits of SVR)
461 for which the A004510 workaround should be applied.
463 The rest of SVR is either not relevant to the decision
464 of whether the erratum is present (e.g. p2040 versus
465 p2041) or is implied by the build target, which controls
466 whether CONFIG_SYS_FSL_ERRATUM_A004510 is set.
468 See Freescale App Note 4493 for more information about
471 CONFIG_A003399_NOR_WORKAROUND
472 Enables a workaround for IFC erratum A003399. It is only
473 required during NOR boot.
475 CONFIG_A008044_WORKAROUND
476 Enables a workaround for T1040/T1042 erratum A008044. It is only
477 required during NAND boot and valid for Rev 1.0 SoC revision
479 CONFIG_SYS_FSL_CORENET_SNOOPVEC_COREONLY
481 This is the value to write into CCSR offset 0x18600
482 according to the A004510 workaround.
484 CONFIG_SYS_FSL_DSP_DDR_ADDR
485 This value denotes start offset of DDR memory which is
486 connected exclusively to the DSP cores.
488 CONFIG_SYS_FSL_DSP_M2_RAM_ADDR
489 This value denotes start offset of M2 memory
490 which is directly connected to the DSP core.
492 CONFIG_SYS_FSL_DSP_M3_RAM_ADDR
493 This value denotes start offset of M3 memory which is directly
494 connected to the DSP core.
496 CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT
497 This value denotes start offset of DSP CCSR space.
499 CONFIG_SYS_FSL_SINGLE_SOURCE_CLK
500 Single Source Clock is clocking mode present in some of FSL SoC's.
501 In this mode, a single differential clock is used to supply
502 clocks to the sysclock, ddrclock and usbclock.
504 CONFIG_SYS_CPC_REINIT_F
505 This CONFIG is defined when the CPC is configured as SRAM at the
506 time of U-boot entry and is required to be re-initialized.
509 Indicates this SoC supports deep sleep feature. If deep sleep is
510 supported, core will start to execute uboot when wakes up.
512 - Generic CPU options:
513 CONFIG_SYS_GENERIC_GLOBAL_DATA
514 Defines global data is initialized in generic board board_init_f().
515 If this macro is defined, global data is created and cleared in
516 generic board board_init_f(). Without this macro, architecture/board
517 should initialize global data before calling board_init_f().
519 CONFIG_SYS_BIG_ENDIAN, CONFIG_SYS_LITTLE_ENDIAN
521 Defines the endianess of the CPU. Implementation of those
522 values is arch specific.
525 Freescale DDR driver in use. This type of DDR controller is
526 found in mpc83xx, mpc85xx, mpc86xx as well as some ARM core
529 CONFIG_SYS_FSL_DDR_ADDR
530 Freescale DDR memory-mapped register base.
532 CONFIG_SYS_FSL_DDR_EMU
533 Specify emulator support for DDR. Some DDR features such as
534 deskew training are not available.
536 CONFIG_SYS_FSL_DDRC_GEN1
537 Freescale DDR1 controller.
539 CONFIG_SYS_FSL_DDRC_GEN2
540 Freescale DDR2 controller.
542 CONFIG_SYS_FSL_DDRC_GEN3
543 Freescale DDR3 controller.
545 CONFIG_SYS_FSL_DDRC_GEN4
546 Freescale DDR4 controller.
548 CONFIG_SYS_FSL_DDRC_ARM_GEN3
549 Freescale DDR3 controller for ARM-based SoCs.
552 Board config to use DDR1. It can be enabled for SoCs with
553 Freescale DDR1 or DDR2 controllers, depending on the board
557 Board config to use DDR2. It can be eanbeld for SoCs with
558 Freescale DDR2 or DDR3 controllers, depending on the board
562 Board config to use DDR3. It can be enabled for SoCs with
563 Freescale DDR3 or DDR3L controllers.
566 Board config to use DDR3L. It can be enabled for SoCs with
570 Board config to use DDR4. It can be enabled for SoCs with
573 CONFIG_SYS_FSL_IFC_BE
574 Defines the IFC controller register space as Big Endian
576 CONFIG_SYS_FSL_IFC_LE
577 Defines the IFC controller register space as Little Endian
579 CONFIG_SYS_FSL_PBL_PBI
580 It enables addition of RCW (Power on reset configuration) in built image.
581 Please refer doc/README.pblimage for more details
583 CONFIG_SYS_FSL_PBL_RCW
584 It adds PBI(pre-boot instructions) commands in u-boot build image.
585 PBI commands can be used to configure SoC before it starts the execution.
586 Please refer doc/README.pblimage for more details
589 It adds a target to create boot binary having SPL binary in PBI format
590 concatenated with u-boot binary.
592 CONFIG_SYS_FSL_DDR_BE
593 Defines the DDR controller register space as Big Endian
595 CONFIG_SYS_FSL_DDR_LE
596 Defines the DDR controller register space as Little Endian
598 CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY
599 Physical address from the view of DDR controllers. It is the
600 same as CONFIG_SYS_DDR_SDRAM_BASE for all Power SoCs. But
601 it could be different for ARM SoCs.
603 CONFIG_SYS_FSL_DDR_INTLV_256B
604 DDR controller interleaving on 256-byte. This is a special
605 interleaving mode, handled by Dickens for Freescale layerscape
608 CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS
609 Number of controllers used as main memory.
611 CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
612 Number of controllers used for other than main memory.
614 CONFIG_SYS_FSL_SEC_BE
615 Defines the SEC controller register space as Big Endian
617 CONFIG_SYS_FSL_SEC_LE
618 Defines the SEC controller register space as Little Endian
620 - Intel Monahans options:
621 CONFIG_SYS_MONAHANS_RUN_MODE_OSC_RATIO
623 Defines the Monahans run mode to oscillator
624 ratio. Valid values are 8, 16, 24, 31. The core
625 frequency is this value multiplied by 13 MHz.
627 CONFIG_SYS_MONAHANS_TURBO_RUN_MODE_RATIO
629 Defines the Monahans turbo mode to oscillator
630 ratio. Valid values are 1 (default if undefined) and
631 2. The core frequency as calculated above is multiplied
635 CONFIG_SYS_INIT_SP_OFFSET
637 Offset relative to CONFIG_SYS_SDRAM_BASE for initial stack
638 pointer. This is needed for the temporary stack before
641 CONFIG_SYS_MIPS_CACHE_MODE
643 Cache operation mode for the MIPS CPU.
644 See also arch/mips/include/asm/mipsregs.h.
646 CONF_CM_CACHABLE_NO_WA
649 CONF_CM_CACHABLE_NONCOHERENT
653 CONF_CM_CACHABLE_ACCELERATED
655 CONFIG_SYS_XWAY_EBU_BOOTCFG
657 Special option for Lantiq XWAY SoCs for booting from NOR flash.
658 See also arch/mips/cpu/mips32/start.S.
660 CONFIG_XWAY_SWAP_BYTES
662 Enable compilation of tools/xway-swap-bytes needed for Lantiq
663 XWAY SoCs for booting from NOR flash. The U-Boot image needs to
664 be swapped if a flash programmer is used.
667 CONFIG_SYS_EXCEPTION_VECTORS_HIGH
669 Select high exception vectors of the ARM core, e.g., do not
670 clear the V bit of the c1 register of CP15.
672 CONFIG_SYS_THUMB_BUILD
674 Use this flag to build U-Boot using the Thumb instruction
675 set for ARM architectures. Thumb instruction set provides
676 better code density. For ARM architectures that support
677 Thumb2 this flag will result in Thumb2 code generated by
680 CONFIG_ARM_ERRATA_716044
681 CONFIG_ARM_ERRATA_742230
682 CONFIG_ARM_ERRATA_743622
683 CONFIG_ARM_ERRATA_751472
684 CONFIG_ARM_ERRATA_794072
685 CONFIG_ARM_ERRATA_761320
687 If set, the workarounds for these ARM errata are applied early
688 during U-Boot startup. Note that these options force the
689 workarounds to be applied; no CPU-type/version detection
690 exists, unlike the similar options in the Linux kernel. Do not
691 set these options unless they apply!
693 NOTE: The following can be machine specific errata. These
694 do have ability to provide rudimentary version and machine
695 specific checks, but expect no product checks.
696 CONFIG_ARM_ERRATA_430973
697 CONFIG_ARM_ERRATA_454179
698 CONFIG_ARM_ERRATA_621766
699 CONFIG_ARM_ERRATA_798870
702 CONFIG_TEGRA_SUPPORT_NON_SECURE
704 Support executing U-Boot in non-secure (NS) mode. Certain
705 impossible actions will be skipped if the CPU is in NS mode,
706 such as ARM architectural timer initialization.
708 - Linux Kernel Interface:
711 U-Boot stores all clock information in Hz
712 internally. For binary compatibility with older Linux
713 kernels (which expect the clocks passed in the
714 bd_info data to be in MHz) the environment variable
715 "clocks_in_mhz" can be defined so that U-Boot
716 converts clock data to MHZ before passing it to the
718 When CONFIG_CLOCKS_IN_MHZ is defined, a definition of
719 "clocks_in_mhz=1" is automatically included in the
722 CONFIG_MEMSIZE_IN_BYTES [relevant for MIPS only]
724 When transferring memsize parameter to Linux, some versions
725 expect it to be in bytes, others in MB.
726 Define CONFIG_MEMSIZE_IN_BYTES to make it in bytes.
730 New kernel versions are expecting firmware settings to be
731 passed using flattened device trees (based on open firmware
735 * New libfdt-based support
736 * Adds the "fdt" command
737 * The bootm command automatically updates the fdt
739 OF_CPU - The proper name of the cpus node (only required for
740 MPC512X and MPC5xxx based boards).
741 OF_SOC - The proper name of the soc node (only required for
742 MPC512X and MPC5xxx based boards).
743 OF_TBCLK - The timebase frequency.
744 OF_STDOUT_PATH - The path to the console device
746 boards with QUICC Engines require OF_QE to set UCC MAC
749 CONFIG_OF_BOARD_SETUP
751 Board code has addition modification that it wants to make
752 to the flat device tree before handing it off to the kernel
754 CONFIG_OF_SYSTEM_SETUP
756 Other code has addition modification that it wants to make
757 to the flat device tree before handing it off to the kernel.
758 This causes ft_system_setup() to be called before booting
763 This define fills in the correct boot CPU in the boot
764 param header, the default value is zero if undefined.
768 U-Boot can detect if an IDE device is present or not.
769 If not, and this new config option is activated, U-Boot
770 removes the ATA node from the DTS before booting Linux,
771 so the Linux IDE driver does not probe the device and
772 crash. This is needed for buggy hardware (uc101) where
773 no pull down resistor is connected to the signal IDE5V_DD7.
775 CONFIG_MACH_TYPE [relevant for ARM only][mandatory]
777 This setting is mandatory for all boards that have only one
778 machine type and must be used to specify the machine type
779 number as it appears in the ARM machine registry
780 (see http://www.arm.linux.org.uk/developer/machines/).
781 Only boards that have multiple machine types supported
782 in a single configuration file and the machine type is
783 runtime discoverable, do not have to use this setting.
785 - vxWorks boot parameters:
787 bootvx constructs a valid bootline using the following
788 environments variables: bootfile, ipaddr, serverip, hostname.
789 It loads the vxWorks image pointed bootfile.
791 CONFIG_SYS_VXWORKS_BOOT_DEVICE - The vxworks device name
792 CONFIG_SYS_VXWORKS_MAC_PTR - Ethernet 6 byte MA -address
793 CONFIG_SYS_VXWORKS_SERVERNAME - Name of the server
794 CONFIG_SYS_VXWORKS_BOOT_ADDR - Address of boot parameters
796 CONFIG_SYS_VXWORKS_ADD_PARAMS
798 Add it at the end of the bootline. E.g "u=username pw=secret"
800 Note: If a "bootargs" environment is defined, it will overwride
801 the defaults discussed just above.
803 - Cache Configuration:
804 CONFIG_SYS_ICACHE_OFF - Do not enable instruction cache in U-Boot
805 CONFIG_SYS_DCACHE_OFF - Do not enable data cache in U-Boot
806 CONFIG_SYS_L2CACHE_OFF- Do not enable L2 cache in U-Boot
808 - Cache Configuration for ARM:
809 CONFIG_SYS_L2_PL310 - Enable support for ARM PL310 L2 cache
811 CONFIG_SYS_PL310_BASE - Physical base address of PL310
812 controller register space
817 Define this if you want support for Amba PrimeCell PL010 UARTs.
821 Define this if you want support for Amba PrimeCell PL011 UARTs.
825 If you have Amba PrimeCell PL011 UARTs, set this variable to
826 the clock speed of the UARTs.
830 If you have Amba PrimeCell PL010 or PL011 UARTs on your board,
831 define this to a list of base addresses for each (supported)
832 port. See e.g. include/configs/versatile.h
834 CONFIG_PL011_SERIAL_RLCR
836 Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
837 have separate receive and transmit line control registers. Set
838 this variable to initialize the extra register.
840 CONFIG_PL011_SERIAL_FLUSH_ON_INIT
842 On some platforms (e.g. U8500) U-Boot is loaded by a second stage
843 boot loader that has already initialized the UART. Define this
844 variable to flush the UART at init time.
846 CONFIG_SERIAL_HW_FLOW_CONTROL
848 Define this variable to enable hw flow control in serial driver.
849 Current user of this option is drivers/serial/nsl16550.c driver
852 Depending on board, define exactly one serial port
853 (like CONFIG_8xx_CONS_SMC1, CONFIG_8xx_CONS_SMC2,
854 CONFIG_8xx_CONS_SCC1, ...), or switch off the serial
855 console by defining CONFIG_8xx_CONS_NONE
857 Note: if CONFIG_8xx_CONS_NONE is defined, the serial
858 port routines must be defined elsewhere
859 (i.e. serial_init(), serial_getc(), ...)
862 Enables console device for a color framebuffer. Needs following
863 defines (cf. smiLynxEM, i8042)
864 VIDEO_FB_LITTLE_ENDIAN graphic memory organisation
866 VIDEO_HW_RECTFILL graphic chip supports
869 VIDEO_HW_BITBLT graphic chip supports
870 bit-blit (cf. smiLynxEM)
871 VIDEO_VISIBLE_COLS visible pixel columns
873 VIDEO_VISIBLE_ROWS visible pixel rows
874 VIDEO_PIXEL_SIZE bytes per pixel
875 VIDEO_DATA_FORMAT graphic data format
876 (0-5, cf. cfb_console.c)
877 VIDEO_FB_ADRS framebuffer address
878 VIDEO_KBD_INIT_FCT keyboard int fct
879 (i.e. i8042_kbd_init())
880 VIDEO_TSTC_FCT test char fct
882 VIDEO_GETC_FCT get char fct
884 CONFIG_CONSOLE_CURSOR cursor drawing on/off
885 (requires blink timer
887 CONFIG_SYS_CONSOLE_BLINK_COUNT blink interval (cf. i8042.c)
888 CONFIG_CONSOLE_TIME display time/date info in
890 (requires CONFIG_CMD_DATE)
891 CONFIG_VIDEO_LOGO display Linux logo in
893 CONFIG_VIDEO_BMP_LOGO use bmp_logo.h instead of
894 linux_logo.h for logo.
895 Requires CONFIG_VIDEO_LOGO
896 CONFIG_CONSOLE_EXTRA_INFO
897 additional board info beside
900 When CONFIG_CFB_CONSOLE_ANSI is defined, console will support
901 a limited number of ANSI escape sequences (cursor control,
902 erase functions and limited graphics rendition control).
904 When CONFIG_CFB_CONSOLE is defined, video console is
905 default i/o. Serial console can be forced with
906 environment 'console=serial'.
908 When CONFIG_SILENT_CONSOLE is defined, all console
909 messages (by U-Boot and Linux!) can be silenced with
910 the "silent" environment variable. See
911 doc/README.silent for more information.
913 CONFIG_SYS_CONSOLE_BG_COL: define the backgroundcolor, default
915 CONFIG_SYS_CONSOLE_FG_COL: define the foregroundcolor, default
919 CONFIG_BAUDRATE - in bps
920 Select one of the baudrates listed in
921 CONFIG_SYS_BAUDRATE_TABLE, see below.
922 CONFIG_SYS_BRGCLK_PRESCALE, baudrate prescale
924 - Console Rx buffer length
925 With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
926 the maximum receive buffer length for the SMC.
927 This option is actual only for 82xx and 8xx possible.
928 If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
929 must be defined, to setup the maximum idle timeout for
932 - Pre-Console Buffer:
933 Prior to the console being initialised (i.e. serial UART
934 initialised etc) all console output is silently discarded.
935 Defining CONFIG_PRE_CONSOLE_BUFFER will cause U-Boot to
936 buffer any console messages prior to the console being
937 initialised to a buffer of size CONFIG_PRE_CON_BUF_SZ
938 bytes located at CONFIG_PRE_CON_BUF_ADDR. The buffer is
939 a circular buffer, so if more than CONFIG_PRE_CON_BUF_SZ
940 bytes are output before the console is initialised, the
941 earlier bytes are discarded.
943 'Sane' compilers will generate smaller code if
944 CONFIG_PRE_CON_BUF_SZ is a power of 2
946 - Safe printf() functions
947 Define CONFIG_SYS_VSNPRINTF to compile in safe versions of
948 the printf() functions. These are defined in
949 include/vsprintf.h and include snprintf(), vsnprintf() and
950 so on. Code size increase is approximately 300-500 bytes.
951 If this option is not given then these functions will
952 silently discard their buffer size argument - this means
953 you are not getting any overflow checking in this case.
955 - Boot Delay: CONFIG_BOOTDELAY - in seconds
956 Delay before automatically booting the default image;
957 set to -1 to disable autoboot.
958 set to -2 to autoboot with no delay and not check for abort
959 (even when CONFIG_ZERO_BOOTDELAY_CHECK is defined).
961 See doc/README.autoboot for these options that
962 work with CONFIG_BOOTDELAY. None are required.
963 CONFIG_BOOT_RETRY_TIME
964 CONFIG_BOOT_RETRY_MIN
965 CONFIG_AUTOBOOT_KEYED
966 CONFIG_AUTOBOOT_PROMPT
967 CONFIG_AUTOBOOT_DELAY_STR
968 CONFIG_AUTOBOOT_STOP_STR
969 CONFIG_AUTOBOOT_DELAY_STR2
970 CONFIG_AUTOBOOT_STOP_STR2
971 CONFIG_ZERO_BOOTDELAY_CHECK
972 CONFIG_RESET_TO_RETRY
976 Only needed when CONFIG_BOOTDELAY is enabled;
977 define a command string that is automatically executed
978 when no character is read on the console interface
979 within "Boot Delay" after reset.
982 This can be used to pass arguments to the bootm
983 command. The value of CONFIG_BOOTARGS goes into the
984 environment value "bootargs".
986 CONFIG_RAMBOOT and CONFIG_NFSBOOT
987 The value of these goes into the environment as
988 "ramboot" and "nfsboot" respectively, and can be used
989 as a convenience, when switching between booting from
993 CONFIG_BOOTCOUNT_LIMIT
994 Implements a mechanism for detecting a repeating reboot
996 http://www.denx.de/wiki/view/DULG/UBootBootCountLimit
999 If no softreset save registers are found on the hardware
1000 "bootcount" is stored in the environment. To prevent a
1001 saveenv on all reboots, the environment variable
1002 "upgrade_available" is used. If "upgrade_available" is
1003 0, "bootcount" is always 0, if "upgrade_available" is
1004 1 "bootcount" is incremented in the environment.
1005 So the Userspace Applikation must set the "upgrade_available"
1006 and "bootcount" variable to 0, if a boot was successfully.
1008 - Pre-Boot Commands:
1011 When this option is #defined, the existence of the
1012 environment variable "preboot" will be checked
1013 immediately before starting the CONFIG_BOOTDELAY
1014 countdown and/or running the auto-boot command resp.
1015 entering interactive mode.
1017 This feature is especially useful when "preboot" is
1018 automatically generated or modified. For an example
1019 see the LWMON board specific code: here "preboot" is
1020 modified when the user holds down a certain
1021 combination of keys on the (special) keyboard when
1024 - Serial Download Echo Mode:
1026 If defined to 1, all characters received during a
1027 serial download (using the "loads" command) are
1028 echoed back. This might be needed by some terminal
1029 emulations (like "cu"), but may as well just take
1030 time on others. This setting #define's the initial
1031 value of the "loads_echo" environment variable.
1033 - Kgdb Serial Baudrate: (if CONFIG_CMD_KGDB is defined)
1034 CONFIG_KGDB_BAUDRATE
1035 Select one of the baudrates listed in
1036 CONFIG_SYS_BAUDRATE_TABLE, see below.
1038 - Monitor Functions:
1039 Monitor commands can be included or excluded
1040 from the build by using the #include files
1041 <config_cmd_all.h> and #undef'ing unwanted
1042 commands, or using <config_cmd_default.h>
1043 and augmenting with additional #define's
1044 for wanted commands.
1046 The default command configuration includes all commands
1047 except those marked below with a "*".
1049 CONFIG_CMD_AES AES 128 CBC encrypt/decrypt
1050 CONFIG_CMD_ASKENV * ask for env variable
1051 CONFIG_CMD_BDI bdinfo
1052 CONFIG_CMD_BEDBUG * Include BedBug Debugger
1053 CONFIG_CMD_BMP * BMP support
1054 CONFIG_CMD_BSP * Board specific commands
1055 CONFIG_CMD_BOOTD bootd
1056 CONFIG_CMD_BOOTI * ARM64 Linux kernel Image support
1057 CONFIG_CMD_CACHE * icache, dcache
1058 CONFIG_CMD_CLK * clock command support
1059 CONFIG_CMD_CONSOLE coninfo
1060 CONFIG_CMD_CRC32 * crc32
1061 CONFIG_CMD_DATE * support for RTC, date/time...
1062 CONFIG_CMD_DHCP * DHCP support
1063 CONFIG_CMD_DIAG * Diagnostics
1064 CONFIG_CMD_DS4510 * ds4510 I2C gpio commands
1065 CONFIG_CMD_DS4510_INFO * ds4510 I2C info command
1066 CONFIG_CMD_DS4510_MEM * ds4510 I2C eeprom/sram commansd
1067 CONFIG_CMD_DS4510_RST * ds4510 I2C rst command
1068 CONFIG_CMD_DTT * Digital Therm and Thermostat
1069 CONFIG_CMD_ECHO echo arguments
1070 CONFIG_CMD_EDITENV edit env variable
1071 CONFIG_CMD_EEPROM * EEPROM read/write support
1072 CONFIG_CMD_ELF * bootelf, bootvx
1073 CONFIG_CMD_ENV_CALLBACK * display details about env callbacks
1074 CONFIG_CMD_ENV_FLAGS * display details about env flags
1075 CONFIG_CMD_ENV_EXISTS * check existence of env variable
1076 CONFIG_CMD_EXPORTENV * export the environment
1077 CONFIG_CMD_EXT2 * ext2 command support
1078 CONFIG_CMD_EXT4 * ext4 command support
1079 CONFIG_CMD_FS_GENERIC * filesystem commands (e.g. load, ls)
1080 that work for multiple fs types
1081 CONFIG_CMD_FS_UUID * Look up a filesystem UUID
1082 CONFIG_CMD_SAVEENV saveenv
1083 CONFIG_CMD_FDC * Floppy Disk Support
1084 CONFIG_CMD_FAT * FAT command support
1085 CONFIG_CMD_FLASH flinfo, erase, protect
1086 CONFIG_CMD_FPGA FPGA device initialization support
1087 CONFIG_CMD_FUSE * Device fuse support
1088 CONFIG_CMD_GETTIME * Get time since boot
1089 CONFIG_CMD_GO * the 'go' command (exec code)
1090 CONFIG_CMD_GREPENV * search environment
1091 CONFIG_CMD_HASH * calculate hash / digest
1092 CONFIG_CMD_HWFLOW * RTS/CTS hw flow control
1093 CONFIG_CMD_I2C * I2C serial bus support
1094 CONFIG_CMD_IDE * IDE harddisk support
1095 CONFIG_CMD_IMI iminfo
1096 CONFIG_CMD_IMLS List all images found in NOR flash
1097 CONFIG_CMD_IMLS_NAND * List all images found in NAND flash
1098 CONFIG_CMD_IMMAP * IMMR dump support
1099 CONFIG_CMD_IOTRACE * I/O tracing for debugging
1100 CONFIG_CMD_IMPORTENV * import an environment
1101 CONFIG_CMD_INI * import data from an ini file into the env
1102 CONFIG_CMD_IRQ * irqinfo
1103 CONFIG_CMD_ITEST Integer/string test of 2 values
1104 CONFIG_CMD_JFFS2 * JFFS2 Support
1105 CONFIG_CMD_KGDB * kgdb
1106 CONFIG_CMD_LDRINFO * ldrinfo (display Blackfin loader)
1107 CONFIG_CMD_LINK_LOCAL * link-local IP address auto-configuration
1109 CONFIG_CMD_LOADB loadb
1110 CONFIG_CMD_LOADS loads
1111 CONFIG_CMD_MD5SUM * print md5 message digest
1112 (requires CONFIG_CMD_MEMORY and CONFIG_MD5)
1113 CONFIG_CMD_MEMINFO * Display detailed memory information
1114 CONFIG_CMD_MEMORY md, mm, nm, mw, cp, cmp, crc, base,
1116 CONFIG_CMD_MEMTEST * mtest
1117 CONFIG_CMD_MISC Misc functions like sleep etc
1118 CONFIG_CMD_MMC * MMC memory mapped support
1119 CONFIG_CMD_MII * MII utility commands
1120 CONFIG_CMD_MTDPARTS * MTD partition support
1121 CONFIG_CMD_NAND * NAND support
1122 CONFIG_CMD_NET bootp, tftpboot, rarpboot
1123 CONFIG_CMD_NFS NFS support
1124 CONFIG_CMD_PCA953X * PCA953x I2C gpio commands
1125 CONFIG_CMD_PCA953X_INFO * PCA953x I2C gpio info command
1126 CONFIG_CMD_PCI * pciinfo
1127 CONFIG_CMD_PCMCIA * PCMCIA support
1128 CONFIG_CMD_PING * send ICMP ECHO_REQUEST to network
1130 CONFIG_CMD_PORTIO * Port I/O
1131 CONFIG_CMD_READ * Read raw data from partition
1132 CONFIG_CMD_REGINFO * Register dump
1133 CONFIG_CMD_RUN run command in env variable
1134 CONFIG_CMD_SANDBOX * sb command to access sandbox features
1135 CONFIG_CMD_SAVES * save S record dump
1136 CONFIG_CMD_SCSI * SCSI Support
1137 CONFIG_CMD_SDRAM * print SDRAM configuration information
1138 (requires CONFIG_CMD_I2C)
1139 CONFIG_CMD_SETGETDCR Support for DCR Register access
1141 CONFIG_CMD_SF * Read/write/erase SPI NOR flash
1142 CONFIG_CMD_SHA1SUM * print sha1 memory digest
1143 (requires CONFIG_CMD_MEMORY)
1144 CONFIG_CMD_SOFTSWITCH * Soft switch setting command for BF60x
1145 CONFIG_CMD_SOURCE "source" command Support
1146 CONFIG_CMD_SPI * SPI serial bus support
1147 CONFIG_CMD_TFTPSRV * TFTP transfer in server mode
1148 CONFIG_CMD_TFTPPUT * TFTP put command (upload)
1149 CONFIG_CMD_TIME * run command and report execution time (ARM specific)
1150 CONFIG_CMD_TIMER * access to the system tick timer
1151 CONFIG_CMD_USB * USB support
1152 CONFIG_CMD_CDP * Cisco Discover Protocol support
1153 CONFIG_CMD_MFSL * Microblaze FSL support
1154 CONFIG_CMD_XIMG Load part of Multi Image
1155 CONFIG_CMD_UUID * Generate random UUID or GUID string
1157 EXAMPLE: If you want all functions except of network
1158 support you can write:
1160 #include "config_cmd_all.h"
1161 #undef CONFIG_CMD_NET
1164 fdt (flattened device tree) command: CONFIG_OF_LIBFDT
1166 Note: Don't enable the "icache" and "dcache" commands
1167 (configuration option CONFIG_CMD_CACHE) unless you know
1168 what you (and your U-Boot users) are doing. Data
1169 cache cannot be enabled on systems like the 8xx or
1170 8260 (where accesses to the IMMR region must be
1171 uncached), and it cannot be disabled on all other
1172 systems where we (mis-) use the data cache to hold an
1173 initial stack and some data.
1176 XXX - this list needs to get updated!
1178 - Regular expression support:
1180 If this variable is defined, U-Boot is linked against
1181 the SLRE (Super Light Regular Expression) library,
1182 which adds regex support to some commands, as for
1183 example "env grep" and "setexpr".
1187 If this variable is defined, U-Boot will use a device tree
1188 to configure its devices, instead of relying on statically
1189 compiled #defines in the board file. This option is
1190 experimental and only available on a few boards. The device
1191 tree is available in the global data as gd->fdt_blob.
1193 U-Boot needs to get its device tree from somewhere. This can
1194 be done using one of the two options below:
1197 If this variable is defined, U-Boot will embed a device tree
1198 binary in its image. This device tree file should be in the
1199 board directory and called <soc>-<board>.dts. The binary file
1200 is then picked up in board_init_f() and made available through
1201 the global data structure as gd->blob.
1204 If this variable is defined, U-Boot will build a device tree
1205 binary. It will be called u-boot.dtb. Architecture-specific
1206 code will locate it at run-time. Generally this works by:
1208 cat u-boot.bin u-boot.dtb >image.bin
1210 and in fact, U-Boot does this for you, creating a file called
1211 u-boot-dtb.bin which is useful in the common case. You can
1212 still use the individual files if you need something more
1217 If this variable is defined, it enables watchdog
1218 support for the SoC. There must be support in the SoC
1219 specific code for a watchdog. For the 8xx and 8260
1220 CPUs, the SIU Watchdog feature is enabled in the SYPCR
1221 register. When supported for a specific SoC is
1222 available, then no further board specific code should
1223 be needed to use it.
1226 When using a watchdog circuitry external to the used
1227 SoC, then define this variable and provide board
1228 specific code for the "hw_watchdog_reset" function.
1230 CONFIG_AT91_HW_WDT_TIMEOUT
1231 specify the timeout in seconds. default 2 seconds.
1234 CONFIG_VERSION_VARIABLE
1235 If this variable is defined, an environment variable
1236 named "ver" is created by U-Boot showing the U-Boot
1237 version as printed by the "version" command.
1238 Any change to this variable will be reverted at the
1243 When CONFIG_CMD_DATE is selected, the type of the RTC
1244 has to be selected, too. Define exactly one of the
1247 CONFIG_RTC_MPC8xx - use internal RTC of MPC8xx
1248 CONFIG_RTC_PCF8563 - use Philips PCF8563 RTC
1249 CONFIG_RTC_MC13XXX - use MC13783 or MC13892 RTC
1250 CONFIG_RTC_MC146818 - use MC146818 RTC
1251 CONFIG_RTC_DS1307 - use Maxim, Inc. DS1307 RTC
1252 CONFIG_RTC_DS1337 - use Maxim, Inc. DS1337 RTC
1253 CONFIG_RTC_DS1338 - use Maxim, Inc. DS1338 RTC
1254 CONFIG_RTC_DS1339 - use Maxim, Inc. DS1339 RTC
1255 CONFIG_RTC_DS164x - use Dallas DS164x RTC
1256 CONFIG_RTC_ISL1208 - use Intersil ISL1208 RTC
1257 CONFIG_RTC_MAX6900 - use Maxim, Inc. MAX6900 RTC
1258 CONFIG_SYS_RTC_DS1337_NOOSC - Turn off the OSC output for DS1337
1259 CONFIG_SYS_RV3029_TCR - enable trickle charger on
1262 Note that if the RTC uses I2C, then the I2C interface
1263 must also be configured. See I2C Support, below.
1266 CONFIG_PCA953X - use NXP's PCA953X series I2C GPIO
1268 The CONFIG_SYS_I2C_PCA953X_WIDTH option specifies a list of
1269 chip-ngpio pairs that tell the PCA953X driver the number of
1270 pins supported by a particular chip.
1272 Note that if the GPIO device uses I2C, then the I2C interface
1273 must also be configured. See I2C Support, below.
1276 When CONFIG_IO_TRACE is selected, U-Boot intercepts all I/O
1277 accesses and can checksum them or write a list of them out
1278 to memory. See the 'iotrace' command for details. This is
1279 useful for testing device drivers since it can confirm that
1280 the driver behaves the same way before and after a code
1281 change. Currently this is supported on sandbox and arm. To
1282 add support for your architecture, add '#include <iotrace.h>'
1283 to the bottom of arch/<arch>/include/asm/io.h and test.
1285 Example output from the 'iotrace stats' command is below.
1286 Note that if the trace buffer is exhausted, the checksum will
1287 still continue to operate.
1290 Start: 10000000 (buffer start address)
1291 Size: 00010000 (buffer size)
1292 Offset: 00000120 (current buffer offset)
1293 Output: 10000120 (start + offset)
1294 Count: 00000018 (number of trace records)
1295 CRC32: 9526fb66 (CRC32 of all trace records)
1297 - Timestamp Support:
1299 When CONFIG_TIMESTAMP is selected, the timestamp
1300 (date and time) of an image is printed by image
1301 commands like bootm or iminfo. This option is
1302 automatically enabled when you select CONFIG_CMD_DATE .
1304 - Partition Labels (disklabels) Supported:
1305 Zero or more of the following:
1306 CONFIG_MAC_PARTITION Apple's MacOS partition table.
1307 CONFIG_DOS_PARTITION MS Dos partition table, traditional on the
1308 Intel architecture, USB sticks, etc.
1309 CONFIG_ISO_PARTITION ISO partition table, used on CDROM etc.
1310 CONFIG_EFI_PARTITION GPT partition table, common when EFI is the
1311 bootloader. Note 2TB partition limit; see
1313 CONFIG_MTD_PARTITIONS Memory Technology Device partition table.
1315 If IDE or SCSI support is enabled (CONFIG_CMD_IDE or
1316 CONFIG_CMD_SCSI) you must configure support for at
1317 least one non-MTD partition type as well.
1320 CONFIG_IDE_RESET_ROUTINE - this is defined in several
1321 board configurations files but used nowhere!
1323 CONFIG_IDE_RESET - is this is defined, IDE Reset will
1324 be performed by calling the function
1325 ide_set_reset(int reset)
1326 which has to be defined in a board specific file
1331 Set this to enable ATAPI support.
1336 Set this to enable support for disks larger than 137GB
1337 Also look at CONFIG_SYS_64BIT_LBA.
1338 Whithout these , LBA48 support uses 32bit variables and will 'only'
1339 support disks up to 2.1TB.
1341 CONFIG_SYS_64BIT_LBA:
1342 When enabled, makes the IDE subsystem use 64bit sector addresses.
1346 At the moment only there is only support for the
1347 SYM53C8XX SCSI controller; define
1348 CONFIG_SCSI_SYM53C8XX to enable it.
1350 CONFIG_SYS_SCSI_MAX_LUN [8], CONFIG_SYS_SCSI_MAX_SCSI_ID [7] and
1351 CONFIG_SYS_SCSI_MAX_DEVICE [CONFIG_SYS_SCSI_MAX_SCSI_ID *
1352 CONFIG_SYS_SCSI_MAX_LUN] can be adjusted to define the
1353 maximum numbers of LUNs, SCSI ID's and target
1355 CONFIG_SYS_SCSI_SYM53C8XX_CCF to fix clock timing (80Mhz)
1357 The environment variable 'scsidevs' is set to the number of
1358 SCSI devices found during the last scan.
1360 - NETWORK Support (PCI):
1362 Support for Intel 8254x/8257x gigabit chips.
1365 Utility code for direct access to the SPI bus on Intel 8257x.
1366 This does not do anything useful unless you set at least one
1367 of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
1369 CONFIG_E1000_SPI_GENERIC
1370 Allow generic access to the SPI bus on the Intel 8257x, for
1371 example with the "sspi" command.
1374 Management command for E1000 devices. When used on devices
1375 with SPI support you can reprogram the EEPROM from U-Boot.
1377 CONFIG_E1000_FALLBACK_MAC
1378 default MAC for empty EEPROM after production.
1381 Support for Intel 82557/82559/82559ER chips.
1382 Optional CONFIG_EEPRO100_SROM_WRITE enables EEPROM
1383 write routine for first time initialisation.
1386 Support for Digital 2114x chips.
1387 Optional CONFIG_TULIP_SELECT_MEDIA for board specific
1388 modem chip initialisation (KS8761/QS6611).
1391 Support for National dp83815 chips.
1394 Support for National dp8382[01] gigabit chips.
1396 - NETWORK Support (other):
1398 CONFIG_DRIVER_AT91EMAC
1399 Support for AT91RM9200 EMAC.
1402 Define this to use reduced MII inteface
1404 CONFIG_DRIVER_AT91EMAC_QUIET
1405 If this defined, the driver is quiet.
1406 The driver doen't show link status messages.
1408 CONFIG_CALXEDA_XGMAC
1409 Support for the Calxeda XGMAC device
1412 Support for SMSC's LAN91C96 chips.
1414 CONFIG_LAN91C96_BASE
1415 Define this to hold the physical address
1416 of the LAN91C96's I/O space
1418 CONFIG_LAN91C96_USE_32_BIT
1419 Define this to enable 32 bit addressing
1422 Support for SMSC's LAN91C111 chip
1424 CONFIG_SMC91111_BASE
1425 Define this to hold the physical address
1426 of the device (I/O space)
1428 CONFIG_SMC_USE_32_BIT
1429 Define this if data bus is 32 bits
1431 CONFIG_SMC_USE_IOFUNCS
1432 Define this to use i/o functions instead of macros
1433 (some hardware wont work with macros)
1435 CONFIG_DRIVER_TI_EMAC
1436 Support for davinci emac
1438 CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT
1439 Define this if you have more then 3 PHYs.
1442 Support for Faraday's FTGMAC100 Gigabit SoC Ethernet
1444 CONFIG_FTGMAC100_EGIGA
1445 Define this to use GE link update with gigabit PHY.
1446 Define this if FTGMAC100 is connected to gigabit PHY.
1447 If your system has 10/100 PHY only, it might not occur
1448 wrong behavior. Because PHY usually return timeout or
1449 useless data when polling gigabit status and gigabit
1450 control registers. This behavior won't affect the
1451 correctnessof 10/100 link speed update.
1454 Support for SMSC's LAN911x and LAN921x chips
1457 Define this to hold the physical address
1458 of the device (I/O space)
1460 CONFIG_SMC911X_32_BIT
1461 Define this if data bus is 32 bits
1463 CONFIG_SMC911X_16_BIT
1464 Define this if data bus is 16 bits. If your processor
1465 automatically converts one 32 bit word to two 16 bit
1466 words you may also try CONFIG_SMC911X_32_BIT.
1469 Support for Renesas on-chip Ethernet controller
1471 CONFIG_SH_ETHER_USE_PORT
1472 Define the number of ports to be used
1474 CONFIG_SH_ETHER_PHY_ADDR
1475 Define the ETH PHY's address
1477 CONFIG_SH_ETHER_CACHE_WRITEBACK
1478 If this option is set, the driver enables cache flush.
1482 Support for PWM modul on the imx6.
1486 Support TPM devices.
1489 Support for i2c bus TPM devices. Only one device
1490 per system is supported at this time.
1492 CONFIG_TPM_TIS_I2C_BUS_NUMBER
1493 Define the the i2c bus number for the TPM device
1495 CONFIG_TPM_TIS_I2C_SLAVE_ADDRESS
1496 Define the TPM's address on the i2c bus
1498 CONFIG_TPM_TIS_I2C_BURST_LIMITATION
1499 Define the burst count bytes upper limit
1501 CONFIG_TPM_ATMEL_TWI
1502 Support for Atmel TWI TPM device. Requires I2C support.
1505 Support for generic parallel port TPM devices. Only one device
1506 per system is supported at this time.
1508 CONFIG_TPM_TIS_BASE_ADDRESS
1509 Base address where the generic TPM device is mapped
1510 to. Contemporary x86 systems usually map it at
1514 Add tpm monitor functions.
1515 Requires CONFIG_TPM. If CONFIG_TPM_AUTH_SESSIONS is set, also
1516 provides monitor access to authorized functions.
1519 Define this to enable the TPM support library which provides
1520 functional interfaces to some TPM commands.
1521 Requires support for a TPM device.
1523 CONFIG_TPM_AUTH_SESSIONS
1524 Define this to enable authorized functions in the TPM library.
1525 Requires CONFIG_TPM and CONFIG_SHA1.
1528 At the moment only the UHCI host controller is
1529 supported (PIP405, MIP405, MPC5200); define
1530 CONFIG_USB_UHCI to enable it.
1531 define CONFIG_USB_KEYBOARD to enable the USB Keyboard
1532 and define CONFIG_USB_STORAGE to enable the USB
1535 Supported are USB Keyboards and USB Floppy drives
1537 MPC5200 USB requires additional defines:
1539 for 528 MHz Clock: 0x0001bbbb
1543 for differential drivers: 0x00001000
1544 for single ended drivers: 0x00005000
1545 for differential drivers on PSC3: 0x00000100
1546 for single ended drivers on PSC3: 0x00004100
1547 CONFIG_SYS_USB_EVENT_POLL
1548 May be defined to allow interrupt polling
1549 instead of using asynchronous interrupts
1551 CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the
1552 txfilltuning field in the EHCI controller on reset.
1554 CONFIG_USB_DWC2_REG_ADDR the physical CPU address of the DWC2
1555 HW module registers.
1558 Define the below if you wish to use the USB console.
1559 Once firmware is rebuilt from a serial console issue the
1560 command "setenv stdin usbtty; setenv stdout usbtty" and
1561 attach your USB cable. The Unix command "dmesg" should print
1562 it has found a new device. The environment variable usbtty
1563 can be set to gserial or cdc_acm to enable your device to
1564 appear to a USB host as a Linux gserial device or a
1565 Common Device Class Abstract Control Model serial device.
1566 If you select usbtty = gserial you should be able to enumerate
1568 # modprobe usbserial vendor=0xVendorID product=0xProductID
1569 else if using cdc_acm, simply setting the environment
1570 variable usbtty to be cdc_acm should suffice. The following
1571 might be defined in YourBoardName.h
1574 Define this to build a UDC device
1577 Define this to have a tty type of device available to
1578 talk to the UDC device
1581 Define this to enable the high speed support for usb
1582 device and usbtty. If this feature is enabled, a routine
1583 int is_usbd_high_speed(void)
1584 also needs to be defined by the driver to dynamically poll
1585 whether the enumeration has succeded at high speed or full
1588 CONFIG_SYS_CONSOLE_IS_IN_ENV
1589 Define this if you want stdin, stdout &/or stderr to
1593 CONFIG_SYS_USB_EXTC_CLK 0xBLAH
1594 Derive USB clock from external clock "blah"
1595 - CONFIG_SYS_USB_EXTC_CLK 0x02
1597 CONFIG_SYS_USB_BRG_CLK 0xBLAH
1598 Derive USB clock from brgclk
1599 - CONFIG_SYS_USB_BRG_CLK 0x04
1601 If you have a USB-IF assigned VendorID then you may wish to
1602 define your own vendor specific values either in BoardName.h
1603 or directly in usbd_vendor_info.h. If you don't define
1604 CONFIG_USBD_MANUFACTURER, CONFIG_USBD_PRODUCT_NAME,
1605 CONFIG_USBD_VENDORID and CONFIG_USBD_PRODUCTID, then U-Boot
1606 should pretend to be a Linux device to it's target host.
1608 CONFIG_USBD_MANUFACTURER
1609 Define this string as the name of your company for
1610 - CONFIG_USBD_MANUFACTURER "my company"
1612 CONFIG_USBD_PRODUCT_NAME
1613 Define this string as the name of your product
1614 - CONFIG_USBD_PRODUCT_NAME "acme usb device"
1616 CONFIG_USBD_VENDORID
1617 Define this as your assigned Vendor ID from the USB
1618 Implementors Forum. This *must* be a genuine Vendor ID
1619 to avoid polluting the USB namespace.
1620 - CONFIG_USBD_VENDORID 0xFFFF
1622 CONFIG_USBD_PRODUCTID
1623 Define this as the unique Product ID
1625 - CONFIG_USBD_PRODUCTID 0xFFFF
1627 - ULPI Layer Support:
1628 The ULPI (UTMI Low Pin (count) Interface) PHYs are supported via
1629 the generic ULPI layer. The generic layer accesses the ULPI PHY
1630 via the platform viewport, so you need both the genric layer and
1631 the viewport enabled. Currently only Chipidea/ARC based
1632 viewport is supported.
1633 To enable the ULPI layer support, define CONFIG_USB_ULPI and
1634 CONFIG_USB_ULPI_VIEWPORT in your board configuration file.
1635 If your ULPI phy needs a different reference clock than the
1636 standard 24 MHz then you have to define CONFIG_ULPI_REF_CLK to
1637 the appropriate value in Hz.
1640 The MMC controller on the Intel PXA is supported. To
1641 enable this define CONFIG_MMC. The MMC can be
1642 accessed from the boot prompt by mapping the device
1643 to physical memory similar to flash. Command line is
1644 enabled with CONFIG_CMD_MMC. The MMC driver also works with
1645 the FAT fs. This is enabled with CONFIG_CMD_FAT.
1648 Support for Renesas on-chip MMCIF controller
1650 CONFIG_SH_MMCIF_ADDR
1651 Define the base address of MMCIF registers
1654 Define the clock frequency for MMCIF
1657 Enable the generic MMC driver
1659 CONFIG_SUPPORT_EMMC_BOOT
1660 Enable some additional features of the eMMC boot partitions.
1662 CONFIG_SUPPORT_EMMC_RPMB
1663 Enable the commands for reading, writing and programming the
1664 key for the Replay Protection Memory Block partition in eMMC.
1666 - USB Device Firmware Update (DFU) class support:
1668 This enables the USB portion of the DFU USB class
1671 This enables the command "dfu" which is used to have
1672 U-Boot create a DFU class device via USB. This command
1673 requires that the "dfu_alt_info" environment variable be
1674 set and define the alt settings to expose to the host.
1677 This enables support for exposing (e)MMC devices via DFU.
1680 This enables support for exposing NAND devices via DFU.
1683 This enables support for exposing RAM via DFU.
1684 Note: DFU spec refer to non-volatile memory usage, but
1685 allow usages beyond the scope of spec - here RAM usage,
1686 one that would help mostly the developer.
1688 CONFIG_SYS_DFU_DATA_BUF_SIZE
1689 Dfu transfer uses a buffer before writing data to the
1690 raw storage device. Make the size (in bytes) of this buffer
1691 configurable. The size of this buffer is also configurable
1692 through the "dfu_bufsiz" environment variable.
1694 CONFIG_SYS_DFU_MAX_FILE_SIZE
1695 When updating files rather than the raw storage device,
1696 we use a static buffer to copy the file into and then write
1697 the buffer once we've been given the whole file. Define
1698 this to the maximum filesize (in bytes) for the buffer.
1699 Default is 4 MiB if undefined.
1701 DFU_DEFAULT_POLL_TIMEOUT
1702 Poll timeout [ms], is the timeout a device can send to the
1703 host. The host must wait for this timeout before sending
1704 a subsequent DFU_GET_STATUS request to the device.
1706 DFU_MANIFEST_POLL_TIMEOUT
1707 Poll timeout [ms], which the device sends to the host when
1708 entering dfuMANIFEST state. Host waits this timeout, before
1709 sending again an USB request to the device.
1711 - USB Device Android Fastboot support:
1713 This enables the command "fastboot" which enables the Android
1714 fastboot mode for the platform's USB device. Fastboot is a USB
1715 protocol for downloading images, flashing and device control
1716 used on Android devices.
1717 See doc/README.android-fastboot for more information.
1719 CONFIG_ANDROID_BOOT_IMAGE
1720 This enables support for booting images which use the Android
1721 image format header.
1723 CONFIG_USB_FASTBOOT_BUF_ADDR
1724 The fastboot protocol requires a large memory buffer for
1725 downloads. Define this to the starting RAM address to use for
1728 CONFIG_USB_FASTBOOT_BUF_SIZE
1729 The fastboot protocol requires a large memory buffer for
1730 downloads. This buffer should be as large as possible for a
1731 platform. Define this to the size available RAM for fastboot.
1733 CONFIG_FASTBOOT_FLASH
1734 The fastboot protocol includes a "flash" command for writing
1735 the downloaded image to a non-volatile storage device. Define
1736 this to enable the "fastboot flash" command.
1738 CONFIG_FASTBOOT_FLASH_MMC_DEV
1739 The fastboot "flash" command requires additional information
1740 regarding the non-volatile storage device. Define this to
1741 the eMMC device that fastboot should use to store the image.
1743 CONFIG_FASTBOOT_GPT_NAME
1744 The fastboot "flash" command supports writing the downloaded
1745 image to the Protective MBR and the Primary GUID Partition
1746 Table. (Additionally, this downloaded image is post-processed
1747 to generate and write the Backup GUID Partition Table.)
1748 This occurs when the specified "partition name" on the
1749 "fastboot flash" command line matches this value.
1750 Default is GPT_ENTRY_NAME (currently "gpt") if undefined.
1752 - Journaling Flash filesystem support:
1753 CONFIG_JFFS2_NAND, CONFIG_JFFS2_NAND_OFF, CONFIG_JFFS2_NAND_SIZE,
1754 CONFIG_JFFS2_NAND_DEV
1755 Define these for a default partition on a NAND device
1757 CONFIG_SYS_JFFS2_FIRST_SECTOR,
1758 CONFIG_SYS_JFFS2_FIRST_BANK, CONFIG_SYS_JFFS2_NUM_BANKS
1759 Define these for a default partition on a NOR device
1761 CONFIG_SYS_JFFS_CUSTOM_PART
1762 Define this to create an own partition. You have to provide a
1763 function struct part_info* jffs2_part_info(int part_num)
1765 If you define only one JFFS2 partition you may also want to
1766 #define CONFIG_SYS_JFFS_SINGLE_PART 1
1767 to disable the command chpart. This is the default when you
1768 have not defined a custom partition
1770 - FAT(File Allocation Table) filesystem write function support:
1773 Define this to enable support for saving memory data as a
1774 file in FAT formatted partition.
1776 This will also enable the command "fatwrite" enabling the
1777 user to write files to FAT.
1779 CBFS (Coreboot Filesystem) support
1782 Define this to enable support for reading from a Coreboot
1783 filesystem. Available commands are cbfsinit, cbfsinfo, cbfsls
1786 - FAT(File Allocation Table) filesystem cluster size:
1787 CONFIG_FS_FAT_MAX_CLUSTSIZE
1789 Define the max cluster size for fat operations else
1790 a default value of 65536 will be defined.
1795 Define this to enable standard (PC-Style) keyboard
1799 Standard PC keyboard driver with US (is default) and
1800 GERMAN key layout (switch via environment 'keymap=de') support.
1801 Export function i8042_kbd_init, i8042_tstc and i8042_getc
1802 for cfb_console. Supports cursor blinking.
1805 Enables a Chrome OS keyboard using the CROS_EC interface.
1806 This uses CROS_EC to communicate with a second microcontroller
1807 which provides key scans on request.
1812 Define this to enable video support (for output to
1815 CONFIG_VIDEO_CT69000
1817 Enable Chips & Technologies 69000 Video chip
1819 CONFIG_VIDEO_SMI_LYNXEM
1820 Enable Silicon Motion SMI 712/710/810 Video chip. The
1821 video output is selected via environment 'videoout'
1822 (1 = LCD and 2 = CRT). If videoout is undefined, CRT is
1825 For the CT69000 and SMI_LYNXEM drivers, videomode is
1826 selected via environment 'videomode'. Two different ways
1828 - "videomode=num" 'num' is a standard LiLo mode numbers.
1829 Following standard modes are supported (* is default):
1831 Colors 640x480 800x600 1024x768 1152x864 1280x1024
1832 -------------+---------------------------------------------
1833 8 bits | 0x301* 0x303 0x305 0x161 0x307
1834 15 bits | 0x310 0x313 0x316 0x162 0x319
1835 16 bits | 0x311 0x314 0x317 0x163 0x31A
1836 24 bits | 0x312 0x315 0x318 ? 0x31B
1837 -------------+---------------------------------------------
1838 (i.e. setenv videomode 317; saveenv; reset;)
1840 - "videomode=bootargs" all the video parameters are parsed
1841 from the bootargs. (See drivers/video/videomodes.c)
1844 CONFIG_VIDEO_SED13806
1845 Enable Epson SED13806 driver. This driver supports 8bpp
1846 and 16bpp modes defined by CONFIG_VIDEO_SED13806_8BPP
1847 or CONFIG_VIDEO_SED13806_16BPP
1850 Enable the Freescale DIU video driver. Reference boards for
1851 SOCs that have a DIU should define this macro to enable DIU
1852 support, and should also define these other macros:
1858 CONFIG_VIDEO_SW_CURSOR
1859 CONFIG_VGA_AS_SINGLE_DEVICE
1861 CONFIG_VIDEO_BMP_LOGO
1863 The DIU driver will look for the 'video-mode' environment
1864 variable, and if defined, enable the DIU as a console during
1865 boot. See the documentation file README.video for a
1866 description of this variable.
1870 Enable the VGA video / BIOS for x86. The alternative if you
1871 are using coreboot is to use the coreboot frame buffer
1878 Define this to enable a custom keyboard support.
1879 This simply calls drv_keyboard_init() which must be
1880 defined in your board-specific files.
1881 The only board using this so far is RBC823.
1883 - LCD Support: CONFIG_LCD
1885 Define this to enable LCD support (for output to LCD
1886 display); also select one of the supported displays
1887 by defining one of these:
1891 HITACHI TX09D70VM1CCA, 3.5", 240x320.
1893 CONFIG_NEC_NL6448AC33:
1895 NEC NL6448AC33-18. Active, color, single scan.
1897 CONFIG_NEC_NL6448BC20
1899 NEC NL6448BC20-08. 6.5", 640x480.
1900 Active, color, single scan.
1902 CONFIG_NEC_NL6448BC33_54
1904 NEC NL6448BC33-54. 10.4", 640x480.
1905 Active, color, single scan.
1909 Sharp 320x240. Active, color, single scan.
1910 It isn't 16x9, and I am not sure what it is.
1912 CONFIG_SHARP_LQ64D341
1914 Sharp LQ64D341 display, 640x480.
1915 Active, color, single scan.
1919 HLD1045 display, 640x480.
1920 Active, color, single scan.
1924 Optrex CBL50840-2 NF-FW 99 22 M5
1926 Hitachi LMG6912RPFC-00T
1930 320x240. Black & white.
1932 Normally display is black on white background; define
1933 CONFIG_SYS_WHITE_ON_BLACK to get it inverted.
1935 CONFIG_LCD_ALIGNMENT
1937 Normally the LCD is page-aligned (typically 4KB). If this is
1938 defined then the LCD will be aligned to this value instead.
1939 For ARM it is sometimes useful to use MMU_SECTION_SIZE
1940 here, since it is cheaper to change data cache settings on
1941 a per-section basis.
1943 CONFIG_CONSOLE_SCROLL_LINES
1945 When the console need to be scrolled, this is the number of
1946 lines to scroll by. It defaults to 1. Increasing this makes
1947 the console jump but can help speed up operation when scrolling
1952 Support drawing of RLE8-compressed bitmaps on the LCD.
1956 Enables an 'i2c edid' command which can read EDID
1957 information over I2C from an attached LCD display.
1959 - Splash Screen Support: CONFIG_SPLASH_SCREEN
1961 If this option is set, the environment is checked for
1962 a variable "splashimage". If found, the usual display
1963 of logo, copyright and system information on the LCD
1964 is suppressed and the BMP image at the address
1965 specified in "splashimage" is loaded instead. The
1966 console is redirected to the "nulldev", too. This
1967 allows for a "silent" boot where a splash screen is
1968 loaded very quickly after power-on.
1970 CONFIG_SPLASHIMAGE_GUARD
1972 If this option is set, then U-Boot will prevent the environment
1973 variable "splashimage" from being set to a problematic address
1974 (see README.displaying-bmps).
1975 This option is useful for targets where, due to alignment
1976 restrictions, an improperly aligned BMP image will cause a data
1977 abort. If you think you will not have problems with unaligned
1978 accesses (for example because your toolchain prevents them)
1979 there is no need to set this option.
1981 CONFIG_SPLASH_SCREEN_ALIGN
1983 If this option is set the splash image can be freely positioned
1984 on the screen. Environment variable "splashpos" specifies the
1985 position as "x,y". If a positive number is given it is used as
1986 number of pixel from left/top. If a negative number is given it
1987 is used as number of pixel from right/bottom. You can also
1988 specify 'm' for centering the image.
1991 setenv splashpos m,m
1992 => image at center of screen
1994 setenv splashpos 30,20
1995 => image at x = 30 and y = 20
1997 setenv splashpos -10,m
1998 => vertically centered image
1999 at x = dspWidth - bmpWidth - 9
2001 - Gzip compressed BMP image support: CONFIG_VIDEO_BMP_GZIP
2003 If this option is set, additionally to standard BMP
2004 images, gzipped BMP images can be displayed via the
2005 splashscreen support or the bmp command.
2007 - Run length encoded BMP image (RLE8) support: CONFIG_VIDEO_BMP_RLE8
2009 If this option is set, 8-bit RLE compressed BMP images
2010 can be displayed via the splashscreen support or the
2013 - Do compressing for memory range:
2016 If this option is set, it would use zlib deflate method
2017 to compress the specified memory at its best effort.
2019 - Compression support:
2022 Enabled by default to support gzip compressed images.
2026 If this option is set, support for bzip2 compressed
2027 images is included. If not, only uncompressed and gzip
2028 compressed images are supported.
2030 NOTE: the bzip2 algorithm requires a lot of RAM, so
2031 the malloc area (as defined by CONFIG_SYS_MALLOC_LEN) should
2036 If this option is set, support for lzma compressed
2039 Note: The LZMA algorithm adds between 2 and 4KB of code and it
2040 requires an amount of dynamic memory that is given by the
2043 (1846 + 768 << (lc + lp)) * sizeof(uint16)
2045 Where lc and lp stand for, respectively, Literal context bits
2046 and Literal pos bits.
2048 This value is upper-bounded by 14MB in the worst case. Anyway,
2049 for a ~4MB large kernel image, we have lc=3 and lp=0 for a
2050 total amount of (1846 + 768 << (3 + 0)) * 2 = ~41KB... that is
2051 a very small buffer.
2053 Use the lzmainfo tool to determinate the lc and lp values and
2054 then calculate the amount of needed dynamic memory (ensuring
2055 the appropriate CONFIG_SYS_MALLOC_LEN value).
2059 If this option is set, support for LZO compressed images
2065 The address of PHY on MII bus.
2067 CONFIG_PHY_CLOCK_FREQ (ppc4xx)
2069 The clock frequency of the MII bus
2073 If this option is set, support for speed/duplex
2074 detection of gigabit PHY is included.
2076 CONFIG_PHY_RESET_DELAY
2078 Some PHY like Intel LXT971A need extra delay after
2079 reset before any MII register access is possible.
2080 For such PHY, set this option to the usec delay
2081 required. (minimum 300usec for LXT971A)
2083 CONFIG_PHY_CMD_DELAY (ppc4xx)
2085 Some PHY like Intel LXT971A need extra delay after
2086 command issued before MII status register can be read
2096 Define a default value for Ethernet address to use
2097 for the respective Ethernet interface, in case this
2098 is not determined automatically.
2103 Define a default value for the IP address to use for
2104 the default Ethernet interface, in case this is not
2105 determined through e.g. bootp.
2106 (Environment variable "ipaddr")
2108 - Server IP address:
2111 Defines a default value for the IP address of a TFTP
2112 server to contact when using the "tftboot" command.
2113 (Environment variable "serverip")
2115 CONFIG_KEEP_SERVERADDR
2117 Keeps the server's MAC address, in the env 'serveraddr'
2118 for passing to bootargs (like Linux's netconsole option)
2120 - Gateway IP address:
2123 Defines a default value for the IP address of the
2124 default router where packets to other networks are
2126 (Environment variable "gatewayip")
2131 Defines a default value for the subnet mask (or
2132 routing prefix) which is used to determine if an IP
2133 address belongs to the local subnet or needs to be
2134 forwarded through a router.
2135 (Environment variable "netmask")
2137 - Multicast TFTP Mode:
2140 Defines whether you want to support multicast TFTP as per
2141 rfc-2090; for example to work with atftp. Lets lots of targets
2142 tftp down the same boot image concurrently. Note: the Ethernet
2143 driver in use must provide a function: mcast() to join/leave a
2146 - BOOTP Recovery Mode:
2147 CONFIG_BOOTP_RANDOM_DELAY
2149 If you have many targets in a network that try to
2150 boot using BOOTP, you may want to avoid that all
2151 systems send out BOOTP requests at precisely the same
2152 moment (which would happen for instance at recovery
2153 from a power failure, when all systems will try to
2154 boot, thus flooding the BOOTP server. Defining
2155 CONFIG_BOOTP_RANDOM_DELAY causes a random delay to be
2156 inserted before sending out BOOTP requests. The
2157 following delays are inserted then:
2159 1st BOOTP request: delay 0 ... 1 sec
2160 2nd BOOTP request: delay 0 ... 2 sec
2161 3rd BOOTP request: delay 0 ... 4 sec
2163 BOOTP requests: delay 0 ... 8 sec
2165 CONFIG_BOOTP_ID_CACHE_SIZE
2167 BOOTP packets are uniquely identified using a 32-bit ID. The
2168 server will copy the ID from client requests to responses and
2169 U-Boot will use this to determine if it is the destination of
2170 an incoming response. Some servers will check that addresses
2171 aren't in use before handing them out (usually using an ARP
2172 ping) and therefore take up to a few hundred milliseconds to
2173 respond. Network congestion may also influence the time it
2174 takes for a response to make it back to the client. If that
2175 time is too long, U-Boot will retransmit requests. In order
2176 to allow earlier responses to still be accepted after these
2177 retransmissions, U-Boot's BOOTP client keeps a small cache of
2178 IDs. The CONFIG_BOOTP_ID_CACHE_SIZE controls the size of this
2179 cache. The default is to keep IDs for up to four outstanding
2180 requests. Increasing this will allow U-Boot to accept offers
2181 from a BOOTP client in networks with unusually high latency.
2183 - DHCP Advanced Options:
2184 You can fine tune the DHCP functionality by defining
2185 CONFIG_BOOTP_* symbols:
2187 CONFIG_BOOTP_SUBNETMASK
2188 CONFIG_BOOTP_GATEWAY
2189 CONFIG_BOOTP_HOSTNAME
2190 CONFIG_BOOTP_NISDOMAIN
2191 CONFIG_BOOTP_BOOTPATH
2192 CONFIG_BOOTP_BOOTFILESIZE
2195 CONFIG_BOOTP_SEND_HOSTNAME
2196 CONFIG_BOOTP_NTPSERVER
2197 CONFIG_BOOTP_TIMEOFFSET
2198 CONFIG_BOOTP_VENDOREX
2199 CONFIG_BOOTP_MAY_FAIL
2201 CONFIG_BOOTP_SERVERIP - TFTP server will be the serverip
2202 environment variable, not the BOOTP server.
2204 CONFIG_BOOTP_MAY_FAIL - If the DHCP server is not found
2205 after the configured retry count, the call will fail
2206 instead of starting over. This can be used to fail over
2207 to Link-local IP address configuration if the DHCP server
2210 CONFIG_BOOTP_DNS2 - If a DHCP client requests the DNS
2211 serverip from a DHCP server, it is possible that more
2212 than one DNS serverip is offered to the client.
2213 If CONFIG_BOOTP_DNS2 is enabled, the secondary DNS
2214 serverip will be stored in the additional environment
2215 variable "dnsip2". The first DNS serverip is always
2216 stored in the variable "dnsip", when CONFIG_BOOTP_DNS
2219 CONFIG_BOOTP_SEND_HOSTNAME - Some DHCP servers are capable
2220 to do a dynamic update of a DNS server. To do this, they
2221 need the hostname of the DHCP requester.
2222 If CONFIG_BOOTP_SEND_HOSTNAME is defined, the content
2223 of the "hostname" environment variable is passed as
2224 option 12 to the DHCP server.
2226 CONFIG_BOOTP_DHCP_REQUEST_DELAY
2228 A 32bit value in microseconds for a delay between
2229 receiving a "DHCP Offer" and sending the "DHCP Request".
2230 This fixes a problem with certain DHCP servers that don't
2231 respond 100% of the time to a "DHCP request". E.g. On an
2232 AT91RM9200 processor running at 180MHz, this delay needed
2233 to be *at least* 15,000 usec before a Windows Server 2003
2234 DHCP server would reply 100% of the time. I recommend at
2235 least 50,000 usec to be safe. The alternative is to hope
2236 that one of the retries will be successful but note that
2237 the DHCP timeout and retry process takes a longer than
2240 - Link-local IP address negotiation:
2241 Negotiate with other link-local clients on the local network
2242 for an address that doesn't require explicit configuration.
2243 This is especially useful if a DHCP server cannot be guaranteed
2244 to exist in all environments that the device must operate.
2246 See doc/README.link-local for more information.
2249 CONFIG_CDP_DEVICE_ID
2251 The device id used in CDP trigger frames.
2253 CONFIG_CDP_DEVICE_ID_PREFIX
2255 A two character string which is prefixed to the MAC address
2260 A printf format string which contains the ascii name of
2261 the port. Normally is set to "eth%d" which sets
2262 eth0 for the first Ethernet, eth1 for the second etc.
2264 CONFIG_CDP_CAPABILITIES
2266 A 32bit integer which indicates the device capabilities;
2267 0x00000010 for a normal host which does not forwards.
2271 An ascii string containing the version of the software.
2275 An ascii string containing the name of the platform.
2279 A 32bit integer sent on the trigger.
2281 CONFIG_CDP_POWER_CONSUMPTION
2283 A 16bit integer containing the power consumption of the
2284 device in .1 of milliwatts.
2286 CONFIG_CDP_APPLIANCE_VLAN_TYPE
2288 A byte containing the id of the VLAN.
2290 - Status LED: CONFIG_STATUS_LED
2292 Several configurations allow to display the current
2293 status using a LED. For instance, the LED will blink
2294 fast while running U-Boot code, stop blinking as
2295 soon as a reply to a BOOTP request was received, and
2296 start blinking slow once the Linux kernel is running
2297 (supported by a status LED driver in the Linux
2298 kernel). Defining CONFIG_STATUS_LED enables this
2304 The status LED can be connected to a GPIO pin.
2305 In such cases, the gpio_led driver can be used as a
2306 status LED backend implementation. Define CONFIG_GPIO_LED
2307 to include the gpio_led driver in the U-Boot binary.
2309 CONFIG_GPIO_LED_INVERTED_TABLE
2310 Some GPIO connected LEDs may have inverted polarity in which
2311 case the GPIO high value corresponds to LED off state and
2312 GPIO low value corresponds to LED on state.
2313 In such cases CONFIG_GPIO_LED_INVERTED_TABLE may be defined
2314 with a list of GPIO LEDs that have inverted polarity.
2316 - CAN Support: CONFIG_CAN_DRIVER
2318 Defining CONFIG_CAN_DRIVER enables CAN driver support
2319 on those systems that support this (optional)
2320 feature, like the TQM8xxL modules.
2322 - I2C Support: CONFIG_SYS_I2C
2324 This enable the NEW i2c subsystem, and will allow you to use
2325 i2c commands at the u-boot command line (as long as you set
2326 CONFIG_CMD_I2C in CONFIG_COMMANDS) and communicate with i2c
2327 based realtime clock chips or other i2c devices. See
2328 common/cmd_i2c.c for a description of the command line
2331 ported i2c driver to the new framework:
2332 - drivers/i2c/soft_i2c.c:
2333 - activate first bus with CONFIG_SYS_I2C_SOFT define
2334 CONFIG_SYS_I2C_SOFT_SPEED and CONFIG_SYS_I2C_SOFT_SLAVE
2335 for defining speed and slave address
2336 - activate second bus with I2C_SOFT_DECLARATIONS2 define
2337 CONFIG_SYS_I2C_SOFT_SPEED_2 and CONFIG_SYS_I2C_SOFT_SLAVE_2
2338 for defining speed and slave address
2339 - activate third bus with I2C_SOFT_DECLARATIONS3 define
2340 CONFIG_SYS_I2C_SOFT_SPEED_3 and CONFIG_SYS_I2C_SOFT_SLAVE_3
2341 for defining speed and slave address
2342 - activate fourth bus with I2C_SOFT_DECLARATIONS4 define
2343 CONFIG_SYS_I2C_SOFT_SPEED_4 and CONFIG_SYS_I2C_SOFT_SLAVE_4
2344 for defining speed and slave address
2346 - drivers/i2c/fsl_i2c.c:
2347 - activate i2c driver with CONFIG_SYS_I2C_FSL
2348 define CONFIG_SYS_FSL_I2C_OFFSET for setting the register
2349 offset CONFIG_SYS_FSL_I2C_SPEED for the i2c speed and
2350 CONFIG_SYS_FSL_I2C_SLAVE for the slave addr of the first
2352 - If your board supports a second fsl i2c bus, define
2353 CONFIG_SYS_FSL_I2C2_OFFSET for the register offset
2354 CONFIG_SYS_FSL_I2C2_SPEED for the speed and
2355 CONFIG_SYS_FSL_I2C2_SLAVE for the slave address of the
2358 - drivers/i2c/tegra_i2c.c:
2359 - activate this driver with CONFIG_SYS_I2C_TEGRA
2360 - This driver adds 4 i2c buses with a fix speed from
2361 100000 and the slave addr 0!
2363 - drivers/i2c/ppc4xx_i2c.c
2364 - activate this driver with CONFIG_SYS_I2C_PPC4XX
2365 - CONFIG_SYS_I2C_PPC4XX_CH0 activate hardware channel 0
2366 - CONFIG_SYS_I2C_PPC4XX_CH1 activate hardware channel 1
2368 - drivers/i2c/i2c_mxc.c
2369 - activate this driver with CONFIG_SYS_I2C_MXC
2370 - define speed for bus 1 with CONFIG_SYS_MXC_I2C1_SPEED
2371 - define slave for bus 1 with CONFIG_SYS_MXC_I2C1_SLAVE
2372 - define speed for bus 2 with CONFIG_SYS_MXC_I2C2_SPEED
2373 - define slave for bus 2 with CONFIG_SYS_MXC_I2C2_SLAVE
2374 - define speed for bus 3 with CONFIG_SYS_MXC_I2C3_SPEED
2375 - define slave for bus 3 with CONFIG_SYS_MXC_I2C3_SLAVE
2376 If those defines are not set, default value is 100000
2377 for speed, and 0 for slave.
2379 - drivers/i2c/rcar_i2c.c:
2380 - activate this driver with CONFIG_SYS_I2C_RCAR
2381 - This driver adds 4 i2c buses
2383 - CONFIG_SYS_RCAR_I2C0_BASE for setting the register channel 0
2384 - CONFIG_SYS_RCAR_I2C0_SPEED for for the speed channel 0
2385 - CONFIG_SYS_RCAR_I2C1_BASE for setting the register channel 1
2386 - CONFIG_SYS_RCAR_I2C1_SPEED for for the speed channel 1
2387 - CONFIG_SYS_RCAR_I2C2_BASE for setting the register channel 2
2388 - CONFIG_SYS_RCAR_I2C2_SPEED for for the speed channel 2
2389 - CONFIG_SYS_RCAR_I2C3_BASE for setting the register channel 3
2390 - CONFIG_SYS_RCAR_I2C3_SPEED for for the speed channel 3
2391 - CONFIF_SYS_RCAR_I2C_NUM_CONTROLLERS for number of i2c buses
2393 - drivers/i2c/sh_i2c.c:
2394 - activate this driver with CONFIG_SYS_I2C_SH
2395 - This driver adds from 2 to 5 i2c buses
2397 - CONFIG_SYS_I2C_SH_BASE0 for setting the register channel 0
2398 - CONFIG_SYS_I2C_SH_SPEED0 for for the speed channel 0
2399 - CONFIG_SYS_I2C_SH_BASE1 for setting the register channel 1
2400 - CONFIG_SYS_I2C_SH_SPEED1 for for the speed channel 1
2401 - CONFIG_SYS_I2C_SH_BASE2 for setting the register channel 2
2402 - CONFIG_SYS_I2C_SH_SPEED2 for for the speed channel 2
2403 - CONFIG_SYS_I2C_SH_BASE3 for setting the register channel 3
2404 - CONFIG_SYS_I2C_SH_SPEED3 for for the speed channel 3
2405 - CONFIG_SYS_I2C_SH_BASE4 for setting the register channel 4
2406 - CONFIG_SYS_I2C_SH_SPEED4 for for the speed channel 4
2407 - CONFIG_SYS_I2C_SH_BASE5 for setting the register channel 5
2408 - CONFIG_SYS_I2C_SH_SPEED5 for for the speed channel 5
2409 - CONFIG_SYS_I2C_SH_NUM_CONTROLLERS for number of i2c buses
2411 - drivers/i2c/omap24xx_i2c.c
2412 - activate this driver with CONFIG_SYS_I2C_OMAP24XX
2413 - CONFIG_SYS_OMAP24_I2C_SPEED speed channel 0
2414 - CONFIG_SYS_OMAP24_I2C_SLAVE slave addr channel 0
2415 - CONFIG_SYS_OMAP24_I2C_SPEED1 speed channel 1
2416 - CONFIG_SYS_OMAP24_I2C_SLAVE1 slave addr channel 1
2417 - CONFIG_SYS_OMAP24_I2C_SPEED2 speed channel 2
2418 - CONFIG_SYS_OMAP24_I2C_SLAVE2 slave addr channel 2
2419 - CONFIG_SYS_OMAP24_I2C_SPEED3 speed channel 3
2420 - CONFIG_SYS_OMAP24_I2C_SLAVE3 slave addr channel 3
2421 - CONFIG_SYS_OMAP24_I2C_SPEED4 speed channel 4
2422 - CONFIG_SYS_OMAP24_I2C_SLAVE4 slave addr channel 4
2424 - drivers/i2c/zynq_i2c.c
2425 - activate this driver with CONFIG_SYS_I2C_ZYNQ
2426 - set CONFIG_SYS_I2C_ZYNQ_SPEED for speed setting
2427 - set CONFIG_SYS_I2C_ZYNQ_SLAVE for slave addr
2429 - drivers/i2c/s3c24x0_i2c.c:
2430 - activate this driver with CONFIG_SYS_I2C_S3C24X0
2431 - This driver adds i2c buses (11 for Exynos5250, Exynos5420
2432 9 i2c buses for Exynos4 and 1 for S3C24X0 SoCs from Samsung)
2433 with a fix speed from 100000 and the slave addr 0!
2435 - drivers/i2c/ihs_i2c.c
2436 - activate this driver with CONFIG_SYS_I2C_IHS
2437 - CONFIG_SYS_I2C_IHS_CH0 activate hardware channel 0
2438 - CONFIG_SYS_I2C_IHS_SPEED_0 speed channel 0
2439 - CONFIG_SYS_I2C_IHS_SLAVE_0 slave addr channel 0
2440 - CONFIG_SYS_I2C_IHS_CH1 activate hardware channel 1
2441 - CONFIG_SYS_I2C_IHS_SPEED_1 speed channel 1
2442 - CONFIG_SYS_I2C_IHS_SLAVE_1 slave addr channel 1
2443 - CONFIG_SYS_I2C_IHS_CH2 activate hardware channel 2
2444 - CONFIG_SYS_I2C_IHS_SPEED_2 speed channel 2
2445 - CONFIG_SYS_I2C_IHS_SLAVE_2 slave addr channel 2
2446 - CONFIG_SYS_I2C_IHS_CH3 activate hardware channel 3
2447 - CONFIG_SYS_I2C_IHS_SPEED_3 speed channel 3
2448 - CONFIG_SYS_I2C_IHS_SLAVE_3 slave addr channel 3
2452 CONFIG_SYS_NUM_I2C_BUSES
2453 Hold the number of i2c buses you want to use. If you
2454 don't use/have i2c muxes on your i2c bus, this
2455 is equal to CONFIG_SYS_NUM_I2C_ADAPTERS, and you can
2458 CONFIG_SYS_I2C_DIRECT_BUS
2459 define this, if you don't use i2c muxes on your hardware.
2460 if CONFIG_SYS_I2C_MAX_HOPS is not defined or == 0 you can
2463 CONFIG_SYS_I2C_MAX_HOPS
2464 define how many muxes are maximal consecutively connected
2465 on one i2c bus. If you not use i2c muxes, omit this
2468 CONFIG_SYS_I2C_BUSES
2469 hold a list of buses you want to use, only used if
2470 CONFIG_SYS_I2C_DIRECT_BUS is not defined, for example
2471 a board with CONFIG_SYS_I2C_MAX_HOPS = 1 and
2472 CONFIG_SYS_NUM_I2C_BUSES = 9:
2474 CONFIG_SYS_I2C_BUSES {{0, {I2C_NULL_HOP}}, \
2475 {0, {{I2C_MUX_PCA9547, 0x70, 1}}}, \
2476 {0, {{I2C_MUX_PCA9547, 0x70, 2}}}, \
2477 {0, {{I2C_MUX_PCA9547, 0x70, 3}}}, \
2478 {0, {{I2C_MUX_PCA9547, 0x70, 4}}}, \
2479 {0, {{I2C_MUX_PCA9547, 0x70, 5}}}, \
2480 {1, {I2C_NULL_HOP}}, \
2481 {1, {{I2C_MUX_PCA9544, 0x72, 1}}}, \
2482 {1, {{I2C_MUX_PCA9544, 0x72, 2}}}, \
2486 bus 0 on adapter 0 without a mux
2487 bus 1 on adapter 0 with a PCA9547 on address 0x70 port 1
2488 bus 2 on adapter 0 with a PCA9547 on address 0x70 port 2
2489 bus 3 on adapter 0 with a PCA9547 on address 0x70 port 3
2490 bus 4 on adapter 0 with a PCA9547 on address 0x70 port 4
2491 bus 5 on adapter 0 with a PCA9547 on address 0x70 port 5
2492 bus 6 on adapter 1 without a mux
2493 bus 7 on adapter 1 with a PCA9544 on address 0x72 port 1
2494 bus 8 on adapter 1 with a PCA9544 on address 0x72 port 2
2496 If you do not have i2c muxes on your board, omit this define.
2498 - Legacy I2C Support: CONFIG_HARD_I2C
2500 NOTE: It is intended to move drivers to CONFIG_SYS_I2C which
2501 provides the following compelling advantages:
2503 - more than one i2c adapter is usable
2504 - approved multibus support
2505 - better i2c mux support
2507 ** Please consider updating your I2C driver now. **
2509 These enable legacy I2C serial bus commands. Defining
2510 CONFIG_HARD_I2C will include the appropriate I2C driver
2511 for the selected CPU.
2513 This will allow you to use i2c commands at the u-boot
2514 command line (as long as you set CONFIG_CMD_I2C in
2515 CONFIG_COMMANDS) and communicate with i2c based realtime
2516 clock chips. See common/cmd_i2c.c for a description of the
2517 command line interface.
2519 CONFIG_HARD_I2C selects a hardware I2C controller.
2521 There are several other quantities that must also be
2522 defined when you define CONFIG_HARD_I2C.
2524 In both cases you will need to define CONFIG_SYS_I2C_SPEED
2525 to be the frequency (in Hz) at which you wish your i2c bus
2526 to run and CONFIG_SYS_I2C_SLAVE to be the address of this node (ie
2527 the CPU's i2c node address).
2529 Now, the u-boot i2c code for the mpc8xx
2530 (arch/powerpc/cpu/mpc8xx/i2c.c) sets the CPU up as a master node
2531 and so its address should therefore be cleared to 0 (See,
2532 eg, MPC823e User's Manual p.16-473). So, set
2533 CONFIG_SYS_I2C_SLAVE to 0.
2535 CONFIG_SYS_I2C_INIT_MPC5XXX
2537 When a board is reset during an i2c bus transfer
2538 chips might think that the current transfer is still
2539 in progress. Reset the slave devices by sending start
2540 commands until the slave device responds.
2542 That's all that's required for CONFIG_HARD_I2C.
2544 If you use the software i2c interface (CONFIG_SYS_I2C_SOFT)
2545 then the following macros need to be defined (examples are
2546 from include/configs/lwmon.h):
2550 (Optional). Any commands necessary to enable the I2C
2551 controller or configure ports.
2553 eg: #define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
2557 (Only for MPC8260 CPU). The I/O port to use (the code
2558 assumes both bits are on the same port). Valid values
2559 are 0..3 for ports A..D.
2563 The code necessary to make the I2C data line active
2564 (driven). If the data line is open collector, this
2567 eg: #define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
2571 The code necessary to make the I2C data line tri-stated
2572 (inactive). If the data line is open collector, this
2575 eg: #define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
2579 Code that returns true if the I2C data line is high,
2582 eg: #define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
2586 If <bit> is true, sets the I2C data line high. If it
2587 is false, it clears it (low).
2589 eg: #define I2C_SDA(bit) \
2590 if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
2591 else immr->im_cpm.cp_pbdat &= ~PB_SDA
2595 If <bit> is true, sets the I2C clock line high. If it
2596 is false, it clears it (low).
2598 eg: #define I2C_SCL(bit) \
2599 if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
2600 else immr->im_cpm.cp_pbdat &= ~PB_SCL
2604 This delay is invoked four times per clock cycle so this
2605 controls the rate of data transfer. The data rate thus
2606 is 1 / (I2C_DELAY * 4). Often defined to be something
2609 #define I2C_DELAY udelay(2)
2611 CONFIG_SOFT_I2C_GPIO_SCL / CONFIG_SOFT_I2C_GPIO_SDA
2613 If your arch supports the generic GPIO framework (asm/gpio.h),
2614 then you may alternatively define the two GPIOs that are to be
2615 used as SCL / SDA. Any of the previous I2C_xxx macros will
2616 have GPIO-based defaults assigned to them as appropriate.
2618 You should define these to the GPIO value as given directly to
2619 the generic GPIO functions.
2621 CONFIG_SYS_I2C_INIT_BOARD
2623 When a board is reset during an i2c bus transfer
2624 chips might think that the current transfer is still
2625 in progress. On some boards it is possible to access
2626 the i2c SCLK line directly, either by using the
2627 processor pin as a GPIO or by having a second pin
2628 connected to the bus. If this option is defined a
2629 custom i2c_init_board() routine in boards/xxx/board.c
2630 is run early in the boot sequence.
2632 CONFIG_SYS_I2C_BOARD_LATE_INIT
2634 An alternative to CONFIG_SYS_I2C_INIT_BOARD. If this option is
2635 defined a custom i2c_board_late_init() routine in
2636 boards/xxx/board.c is run AFTER the operations in i2c_init()
2637 is completed. This callpoint can be used to unreset i2c bus
2638 using CPU i2c controller register accesses for CPUs whose i2c
2639 controller provide such a method. It is called at the end of
2640 i2c_init() to allow i2c_init operations to setup the i2c bus
2641 controller on the CPU (e.g. setting bus speed & slave address).
2643 CONFIG_I2CFAST (PPC405GP|PPC405EP only)
2645 This option enables configuration of bi_iic_fast[] flags
2646 in u-boot bd_info structure based on u-boot environment
2647 variable "i2cfast". (see also i2cfast)
2649 CONFIG_I2C_MULTI_BUS
2651 This option allows the use of multiple I2C buses, each of which
2652 must have a controller. At any point in time, only one bus is
2653 active. To switch to a different bus, use the 'i2c dev' command.
2654 Note that bus numbering is zero-based.
2656 CONFIG_SYS_I2C_NOPROBES
2658 This option specifies a list of I2C devices that will be skipped
2659 when the 'i2c probe' command is issued. If CONFIG_I2C_MULTI_BUS
2660 is set, specify a list of bus-device pairs. Otherwise, specify
2661 a 1D array of device addresses
2664 #undef CONFIG_I2C_MULTI_BUS
2665 #define CONFIG_SYS_I2C_NOPROBES {0x50,0x68}
2667 will skip addresses 0x50 and 0x68 on a board with one I2C bus
2669 #define CONFIG_I2C_MULTI_BUS
2670 #define CONFIG_SYS_I2C_MULTI_NOPROBES {{0,0x50},{0,0x68},{1,0x54}}
2672 will skip addresses 0x50 and 0x68 on bus 0 and address 0x54 on bus 1
2674 CONFIG_SYS_SPD_BUS_NUM
2676 If defined, then this indicates the I2C bus number for DDR SPD.
2677 If not defined, then U-Boot assumes that SPD is on I2C bus 0.
2679 CONFIG_SYS_RTC_BUS_NUM
2681 If defined, then this indicates the I2C bus number for the RTC.
2682 If not defined, then U-Boot assumes that RTC is on I2C bus 0.
2684 CONFIG_SYS_DTT_BUS_NUM
2686 If defined, then this indicates the I2C bus number for the DTT.
2687 If not defined, then U-Boot assumes that DTT is on I2C bus 0.
2689 CONFIG_SYS_I2C_DTT_ADDR:
2691 If defined, specifies the I2C address of the DTT device.
2692 If not defined, then U-Boot uses predefined value for
2693 specified DTT device.
2695 CONFIG_SOFT_I2C_READ_REPEATED_START
2697 defining this will force the i2c_read() function in
2698 the soft_i2c driver to perform an I2C repeated start
2699 between writing the address pointer and reading the
2700 data. If this define is omitted the default behaviour
2701 of doing a stop-start sequence will be used. Most I2C
2702 devices can use either method, but some require one or
2705 - SPI Support: CONFIG_SPI
2707 Enables SPI driver (so far only tested with
2708 SPI EEPROM, also an instance works with Crystal A/D and
2709 D/As on the SACSng board)
2713 Enables the driver for SPI controller on SuperH. Currently
2714 only SH7757 is supported.
2718 Enables extended (16-bit) SPI EEPROM addressing.
2719 (symmetrical to CONFIG_I2C_X)
2723 Enables a software (bit-bang) SPI driver rather than
2724 using hardware support. This is a general purpose
2725 driver that only requires three general I/O port pins
2726 (two outputs, one input) to function. If this is
2727 defined, the board configuration must define several
2728 SPI configuration items (port pins to use, etc). For
2729 an example, see include/configs/sacsng.h.
2733 Enables a hardware SPI driver for general-purpose reads
2734 and writes. As with CONFIG_SOFT_SPI, the board configuration
2735 must define a list of chip-select function pointers.
2736 Currently supported on some MPC8xxx processors. For an
2737 example, see include/configs/mpc8349emds.h.
2741 Enables the driver for the SPI controllers on i.MX and MXC
2742 SoCs. Currently i.MX31/35/51 are supported.
2744 CONFIG_SYS_SPI_MXC_WAIT
2745 Timeout for waiting until spi transfer completed.
2746 default: (CONFIG_SYS_HZ/100) /* 10 ms */
2748 - FPGA Support: CONFIG_FPGA
2750 Enables FPGA subsystem.
2752 CONFIG_FPGA_<vendor>
2754 Enables support for specific chip vendors.
2757 CONFIG_FPGA_<family>
2759 Enables support for FPGA family.
2760 (SPARTAN2, SPARTAN3, VIRTEX2, CYCLONE2, ACEX1K, ACEX)
2764 Specify the number of FPGA devices to support.
2766 CONFIG_CMD_FPGA_LOADMK
2768 Enable support for fpga loadmk command
2770 CONFIG_CMD_FPGA_LOADP
2772 Enable support for fpga loadp command - load partial bitstream
2774 CONFIG_CMD_FPGA_LOADBP
2776 Enable support for fpga loadbp command - load partial bitstream
2779 CONFIG_SYS_FPGA_PROG_FEEDBACK
2781 Enable printing of hash marks during FPGA configuration.
2783 CONFIG_SYS_FPGA_CHECK_BUSY
2785 Enable checks on FPGA configuration interface busy
2786 status by the configuration function. This option
2787 will require a board or device specific function to
2792 If defined, a function that provides delays in the FPGA
2793 configuration driver.
2795 CONFIG_SYS_FPGA_CHECK_CTRLC
2796 Allow Control-C to interrupt FPGA configuration
2798 CONFIG_SYS_FPGA_CHECK_ERROR
2800 Check for configuration errors during FPGA bitfile
2801 loading. For example, abort during Virtex II
2802 configuration if the INIT_B line goes low (which
2803 indicated a CRC error).
2805 CONFIG_SYS_FPGA_WAIT_INIT
2807 Maximum time to wait for the INIT_B line to de-assert
2808 after PROB_B has been de-asserted during a Virtex II
2809 FPGA configuration sequence. The default time is 500
2812 CONFIG_SYS_FPGA_WAIT_BUSY
2814 Maximum time to wait for BUSY to de-assert during
2815 Virtex II FPGA configuration. The default is 5 ms.
2817 CONFIG_SYS_FPGA_WAIT_CONFIG
2819 Time to wait after FPGA configuration. The default is
2822 - Configuration Management:
2825 Some SoCs need special image types (e.g. U-Boot binary
2826 with a special header) as build targets. By defining
2827 CONFIG_BUILD_TARGET in the SoC / board header, this
2828 special image will be automatically built upon calling
2833 If defined, this string will be added to the U-Boot
2834 version information (U_BOOT_VERSION)
2836 - Vendor Parameter Protection:
2838 U-Boot considers the values of the environment
2839 variables "serial#" (Board Serial Number) and
2840 "ethaddr" (Ethernet Address) to be parameters that
2841 are set once by the board vendor / manufacturer, and
2842 protects these variables from casual modification by
2843 the user. Once set, these variables are read-only,
2844 and write or delete attempts are rejected. You can
2845 change this behaviour:
2847 If CONFIG_ENV_OVERWRITE is #defined in your config
2848 file, the write protection for vendor parameters is
2849 completely disabled. Anybody can change or delete
2852 Alternatively, if you #define _both_ CONFIG_ETHADDR
2853 _and_ CONFIG_OVERWRITE_ETHADDR_ONCE, a default
2854 Ethernet address is installed in the environment,
2855 which can be changed exactly ONCE by the user. [The
2856 serial# is unaffected by this, i. e. it remains
2859 The same can be accomplished in a more flexible way
2860 for any variable by configuring the type of access
2861 to allow for those variables in the ".flags" variable
2862 or define CONFIG_ENV_FLAGS_LIST_STATIC.
2867 Define this variable to enable the reservation of
2868 "protected RAM", i. e. RAM which is not overwritten
2869 by U-Boot. Define CONFIG_PRAM to hold the number of
2870 kB you want to reserve for pRAM. You can overwrite
2871 this default value by defining an environment
2872 variable "pram" to the number of kB you want to
2873 reserve. Note that the board info structure will
2874 still show the full amount of RAM. If pRAM is
2875 reserved, a new environment variable "mem" will
2876 automatically be defined to hold the amount of
2877 remaining RAM in a form that can be passed as boot
2878 argument to Linux, for instance like that:
2880 setenv bootargs ... mem=\${mem}
2883 This way you can tell Linux not to use this memory,
2884 either, which results in a memory region that will
2885 not be affected by reboots.
2887 *WARNING* If your board configuration uses automatic
2888 detection of the RAM size, you must make sure that
2889 this memory test is non-destructive. So far, the
2890 following board configurations are known to be
2893 IVMS8, IVML24, SPD8xx, TQM8xxL,
2894 HERMES, IP860, RPXlite, LWMON,
2897 - Access to physical memory region (> 4GB)
2898 Some basic support is provided for operations on memory not
2899 normally accessible to U-Boot - e.g. some architectures
2900 support access to more than 4GB of memory on 32-bit
2901 machines using physical address extension or similar.
2902 Define CONFIG_PHYSMEM to access this basic support, which
2903 currently only supports clearing the memory.
2908 Define this variable to stop the system in case of a
2909 fatal error, so that you have to reset it manually.
2910 This is probably NOT a good idea for an embedded
2911 system where you want the system to reboot
2912 automatically as fast as possible, but it may be
2913 useful during development since you can try to debug
2914 the conditions that lead to the situation.
2916 CONFIG_NET_RETRY_COUNT
2918 This variable defines the number of retries for
2919 network operations like ARP, RARP, TFTP, or BOOTP
2920 before giving up the operation. If not defined, a
2921 default value of 5 is used.
2925 Timeout waiting for an ARP reply in milliseconds.
2929 Timeout in milliseconds used in NFS protocol.
2930 If you encounter "ERROR: Cannot umount" in nfs command,
2931 try longer timeout such as
2932 #define CONFIG_NFS_TIMEOUT 10000UL
2934 - Command Interpreter:
2935 CONFIG_AUTO_COMPLETE
2937 Enable auto completion of commands using TAB.
2939 CONFIG_SYS_PROMPT_HUSH_PS2
2941 This defines the secondary prompt string, which is
2942 printed when the command interpreter needs more input
2943 to complete a command. Usually "> ".
2947 In the current implementation, the local variables
2948 space and global environment variables space are
2949 separated. Local variables are those you define by
2950 simply typing `name=value'. To access a local
2951 variable later on, you have write `$name' or
2952 `${name}'; to execute the contents of a variable
2953 directly type `$name' at the command prompt.
2955 Global environment variables are those you use
2956 setenv/printenv to work with. To run a command stored
2957 in such a variable, you need to use the run command,
2958 and you must not use the '$' sign to access them.
2960 To store commands and special characters in a
2961 variable, please use double quotation marks
2962 surrounding the whole text of the variable, instead
2963 of the backslashes before semicolons and special
2966 - Command Line Editing and History:
2967 CONFIG_CMDLINE_EDITING
2969 Enable editing and History functions for interactive
2970 command line input operations
2972 - Default Environment:
2973 CONFIG_EXTRA_ENV_SETTINGS
2975 Define this to contain any number of null terminated
2976 strings (variable = value pairs) that will be part of
2977 the default environment compiled into the boot image.
2979 For example, place something like this in your
2980 board's config file:
2982 #define CONFIG_EXTRA_ENV_SETTINGS \
2986 Warning: This method is based on knowledge about the
2987 internal format how the environment is stored by the
2988 U-Boot code. This is NOT an official, exported
2989 interface! Although it is unlikely that this format
2990 will change soon, there is no guarantee either.
2991 You better know what you are doing here.
2993 Note: overly (ab)use of the default environment is
2994 discouraged. Make sure to check other ways to preset
2995 the environment like the "source" command or the
2998 CONFIG_ENV_VARS_UBOOT_CONFIG
3000 Define this in order to add variables describing the
3001 U-Boot build configuration to the default environment.
3002 These will be named arch, cpu, board, vendor, and soc.
3004 Enabling this option will cause the following to be defined:
3012 CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
3014 Define this in order to add variables describing certain
3015 run-time determined information about the hardware to the
3016 environment. These will be named board_name, board_rev.
3018 CONFIG_DELAY_ENVIRONMENT
3020 Normally the environment is loaded when the board is
3021 initialised so that it is available to U-Boot. This inhibits
3022 that so that the environment is not available until
3023 explicitly loaded later by U-Boot code. With CONFIG_OF_CONTROL
3024 this is instead controlled by the value of
3025 /config/load-environment.
3027 - DataFlash Support:
3028 CONFIG_HAS_DATAFLASH
3030 Defining this option enables DataFlash features and
3031 allows to read/write in Dataflash via the standard
3034 - Serial Flash support
3037 Defining this option enables SPI flash commands
3038 'sf probe/read/write/erase/update'.
3040 Usage requires an initial 'probe' to define the serial
3041 flash parameters, followed by read/write/erase/update
3044 The following defaults may be provided by the platform
3045 to handle the common case when only a single serial
3046 flash is present on the system.
3048 CONFIG_SF_DEFAULT_BUS Bus identifier
3049 CONFIG_SF_DEFAULT_CS Chip-select
3050 CONFIG_SF_DEFAULT_MODE (see include/spi.h)
3051 CONFIG_SF_DEFAULT_SPEED in Hz
3055 Define this option to include a destructive SPI flash
3058 CONFIG_SPI_FLASH_BAR Ban/Extended Addr Reg
3060 Define this option to use the Bank addr/Extended addr
3061 support on SPI flashes which has size > 16Mbytes.
3063 CONFIG_SF_DUAL_FLASH Dual flash memories
3065 Define this option to use dual flash support where two flash
3066 memories can be connected with a given cs line.
3067 Currently Xilinx Zynq qspi supports these type of connections.
3069 CONFIG_SYS_SPI_ST_ENABLE_WP_PIN
3070 enable the W#/Vpp signal to disable writing to the status
3071 register on ST MICRON flashes like the N25Q128.
3072 The status register write enable/disable bit, combined with
3073 the W#/VPP signal provides hardware data protection for the
3074 device as follows: When the enable/disable bit is set to 1,
3075 and the W#/VPP signal is driven LOW, the status register
3076 nonvolatile bits become read-only and the WRITE STATUS REGISTER
3077 operation will not execute. The only way to exit this
3078 hardware-protected mode is to drive W#/VPP HIGH.
3080 - SystemACE Support:
3083 Adding this option adds support for Xilinx SystemACE
3084 chips attached via some sort of local bus. The address
3085 of the chip must also be defined in the
3086 CONFIG_SYS_SYSTEMACE_BASE macro. For example:
3088 #define CONFIG_SYSTEMACE
3089 #define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
3091 When SystemACE support is added, the "ace" device type
3092 becomes available to the fat commands, i.e. fatls.
3094 - TFTP Fixed UDP Port:
3097 If this is defined, the environment variable tftpsrcp
3098 is used to supply the TFTP UDP source port value.
3099 If tftpsrcp isn't defined, the normal pseudo-random port
3100 number generator is used.
3102 Also, the environment variable tftpdstp is used to supply
3103 the TFTP UDP destination port value. If tftpdstp isn't
3104 defined, the normal port 69 is used.
3106 The purpose for tftpsrcp is to allow a TFTP server to
3107 blindly start the TFTP transfer using the pre-configured
3108 target IP address and UDP port. This has the effect of
3109 "punching through" the (Windows XP) firewall, allowing
3110 the remainder of the TFTP transfer to proceed normally.
3111 A better solution is to properly configure the firewall,
3112 but sometimes that is not allowed.
3117 This enables a generic 'hash' command which can produce
3118 hashes / digests from a few algorithms (e.g. SHA1, SHA256).
3122 Enable the hash verify command (hash -v). This adds to code
3125 CONFIG_SHA1 - This option enables support of hashing using SHA1
3126 algorithm. The hash is calculated in software.
3127 CONFIG_SHA256 - This option enables support of hashing using
3128 SHA256 algorithm. The hash is calculated in software.
3129 CONFIG_SHA_HW_ACCEL - This option enables hardware acceleration
3130 for SHA1/SHA256 hashing.
3131 This affects the 'hash' command and also the
3132 hash_lookup_algo() function.
3133 CONFIG_SHA_PROG_HW_ACCEL - This option enables
3134 hardware-acceleration for SHA1/SHA256 progressive hashing.
3135 Data can be streamed in a block at a time and the hashing
3136 is performed in hardware.
3138 Note: There is also a sha1sum command, which should perhaps
3139 be deprecated in favour of 'hash sha1'.
3141 - Freescale i.MX specific commands:
3142 CONFIG_CMD_HDMIDETECT
3143 This enables 'hdmidet' command which returns true if an
3144 HDMI monitor is detected. This command is i.MX 6 specific.
3147 This enables the 'bmode' (bootmode) command for forcing
3148 a boot from specific media.
3150 This is useful for forcing the ROM's usb downloader to
3151 activate upon a watchdog reset which is nice when iterating
3152 on U-Boot. Using the reset button or running bmode normal
3153 will set it back to normal. This command currently
3154 supports i.MX53 and i.MX6.
3159 This enables the RSA algorithm used for FIT image verification
3160 in U-Boot. See doc/uImage.FIT/signature.txt for more information.
3162 The Modular Exponentiation algorithm in RSA is implemented using
3163 driver model. So CONFIG_DM needs to be enabled by default for this
3164 library to function.
3166 The signing part is build into mkimage regardless of this
3167 option. The software based modular exponentiation is built into
3168 mkimage irrespective of this option.
3170 - bootcount support:
3171 CONFIG_BOOTCOUNT_LIMIT
3173 This enables the bootcounter support, see:
3174 http://www.denx.de/wiki/DULG/UBootBootCountLimit
3177 enable special bootcounter support on at91sam9xe based boards.
3179 enable special bootcounter support on blackfin based boards.
3181 enable special bootcounter support on da850 based boards.
3182 CONFIG_BOOTCOUNT_RAM
3183 enable support for the bootcounter in RAM
3184 CONFIG_BOOTCOUNT_I2C
3185 enable support for the bootcounter on an i2c (like RTC) device.
3186 CONFIG_SYS_I2C_RTC_ADDR = i2c chip address
3187 CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for
3189 CONFIG_BOOTCOUNT_ALEN = address len
3191 - Show boot progress:
3192 CONFIG_SHOW_BOOT_PROGRESS
3194 Defining this option allows to add some board-
3195 specific code (calling a user-provided function
3196 "show_boot_progress(int)") that enables you to show
3197 the system's boot progress on some display (for
3198 example, some LED's) on your board. At the moment,
3199 the following checkpoints are implemented:
3202 Legacy uImage format:
3205 1 common/cmd_bootm.c before attempting to boot an image
3206 -1 common/cmd_bootm.c Image header has bad magic number
3207 2 common/cmd_bootm.c Image header has correct magic number
3208 -2 common/cmd_bootm.c Image header has bad checksum
3209 3 common/cmd_bootm.c Image header has correct checksum
3210 -3 common/cmd_bootm.c Image data has bad checksum
3211 4 common/cmd_bootm.c Image data has correct checksum
3212 -4 common/cmd_bootm.c Image is for unsupported architecture
3213 5 common/cmd_bootm.c Architecture check OK
3214 -5 common/cmd_bootm.c Wrong Image Type (not kernel, multi)
3215 6 common/cmd_bootm.c Image Type check OK
3216 -6 common/cmd_bootm.c gunzip uncompression error
3217 -7 common/cmd_bootm.c Unimplemented compression type
3218 7 common/cmd_bootm.c Uncompression OK
3219 8 common/cmd_bootm.c No uncompress/copy overwrite error
3220 -9 common/cmd_bootm.c Unsupported OS (not Linux, BSD, VxWorks, QNX)
3222 9 common/image.c Start initial ramdisk verification
3223 -10 common/image.c Ramdisk header has bad magic number
3224 -11 common/image.c Ramdisk header has bad checksum
3225 10 common/image.c Ramdisk header is OK
3226 -12 common/image.c Ramdisk data has bad checksum
3227 11 common/image.c Ramdisk data has correct checksum
3228 12 common/image.c Ramdisk verification complete, start loading
3229 -13 common/image.c Wrong Image Type (not PPC Linux ramdisk)
3230 13 common/image.c Start multifile image verification
3231 14 common/image.c No initial ramdisk, no multifile, continue.
3233 15 arch/<arch>/lib/bootm.c All preparation done, transferring control to OS
3235 -30 arch/powerpc/lib/board.c Fatal error, hang the system
3236 -31 post/post.c POST test failed, detected by post_output_backlog()
3237 -32 post/post.c POST test failed, detected by post_run_single()
3239 34 common/cmd_doc.c before loading a Image from a DOC device
3240 -35 common/cmd_doc.c Bad usage of "doc" command
3241 35 common/cmd_doc.c correct usage of "doc" command
3242 -36 common/cmd_doc.c No boot device
3243 36 common/cmd_doc.c correct boot device
3244 -37 common/cmd_doc.c Unknown Chip ID on boot device
3245 37 common/cmd_doc.c correct chip ID found, device available
3246 -38 common/cmd_doc.c Read Error on boot device
3247 38 common/cmd_doc.c reading Image header from DOC device OK
3248 -39 common/cmd_doc.c Image header has bad magic number
3249 39 common/cmd_doc.c Image header has correct magic number
3250 -40 common/cmd_doc.c Error reading Image from DOC device
3251 40 common/cmd_doc.c Image header has correct magic number
3252 41 common/cmd_ide.c before loading a Image from a IDE device
3253 -42 common/cmd_ide.c Bad usage of "ide" command
3254 42 common/cmd_ide.c correct usage of "ide" command
3255 -43 common/cmd_ide.c No boot device
3256 43 common/cmd_ide.c boot device found
3257 -44 common/cmd_ide.c Device not available
3258 44 common/cmd_ide.c Device available
3259 -45 common/cmd_ide.c wrong partition selected
3260 45 common/cmd_ide.c partition selected
3261 -46 common/cmd_ide.c Unknown partition table
3262 46 common/cmd_ide.c valid partition table found
3263 -47 common/cmd_ide.c Invalid partition type
3264 47 common/cmd_ide.c correct partition type
3265 -48 common/cmd_ide.c Error reading Image Header on boot device
3266 48 common/cmd_ide.c reading Image Header from IDE device OK
3267 -49 common/cmd_ide.c Image header has bad magic number
3268 49 common/cmd_ide.c Image header has correct magic number
3269 -50 common/cmd_ide.c Image header has bad checksum
3270 50 common/cmd_ide.c Image header has correct checksum
3271 -51 common/cmd_ide.c Error reading Image from IDE device
3272 51 common/cmd_ide.c reading Image from IDE device OK
3273 52 common/cmd_nand.c before loading a Image from a NAND device
3274 -53 common/cmd_nand.c Bad usage of "nand" command
3275 53 common/cmd_nand.c correct usage of "nand" command
3276 -54 common/cmd_nand.c No boot device
3277 54 common/cmd_nand.c boot device found
3278 -55 common/cmd_nand.c Unknown Chip ID on boot device
3279 55 common/cmd_nand.c correct chip ID found, device available
3280 -56 common/cmd_nand.c Error reading Image Header on boot device
3281 56 common/cmd_nand.c reading Image Header from NAND device OK
3282 -57 common/cmd_nand.c Image header has bad magic number
3283 57 common/cmd_nand.c Image header has correct magic number
3284 -58 common/cmd_nand.c Error reading Image from NAND device
3285 58 common/cmd_nand.c reading Image from NAND device OK
3287 -60 common/env_common.c Environment has a bad CRC, using default
3289 64 net/eth.c starting with Ethernet configuration.
3290 -64 net/eth.c no Ethernet found.
3291 65 net/eth.c Ethernet found.
3293 -80 common/cmd_net.c usage wrong
3294 80 common/cmd_net.c before calling net_loop()
3295 -81 common/cmd_net.c some error in net_loop() occurred
3296 81 common/cmd_net.c net_loop() back without error
3297 -82 common/cmd_net.c size == 0 (File with size 0 loaded)
3298 82 common/cmd_net.c trying automatic boot
3299 83 common/cmd_net.c running "source" command
3300 -83 common/cmd_net.c some error in automatic boot or "source" command
3301 84 common/cmd_net.c end without errors
3306 100 common/cmd_bootm.c Kernel FIT Image has correct format
3307 -100 common/cmd_bootm.c Kernel FIT Image has incorrect format
3308 101 common/cmd_bootm.c No Kernel subimage unit name, using configuration
3309 -101 common/cmd_bootm.c Can't get configuration for kernel subimage
3310 102 common/cmd_bootm.c Kernel unit name specified
3311 -103 common/cmd_bootm.c Can't get kernel subimage node offset
3312 103 common/cmd_bootm.c Found configuration node
3313 104 common/cmd_bootm.c Got kernel subimage node offset
3314 -104 common/cmd_bootm.c Kernel subimage hash verification failed
3315 105 common/cmd_bootm.c Kernel subimage hash verification OK
3316 -105 common/cmd_bootm.c Kernel subimage is for unsupported architecture
3317 106 common/cmd_bootm.c Architecture check OK
3318 -106 common/cmd_bootm.c Kernel subimage has wrong type
3319 107 common/cmd_bootm.c Kernel subimage type OK
3320 -107 common/cmd_bootm.c Can't get kernel subimage data/size
3321 108 common/cmd_bootm.c Got kernel subimage data/size
3322 -108 common/cmd_bootm.c Wrong image type (not legacy, FIT)
3323 -109 common/cmd_bootm.c Can't get kernel subimage type
3324 -110 common/cmd_bootm.c Can't get kernel subimage comp
3325 -111 common/cmd_bootm.c Can't get kernel subimage os
3326 -112 common/cmd_bootm.c Can't get kernel subimage load address
3327 -113 common/cmd_bootm.c Image uncompress/copy overwrite error
3329 120 common/image.c Start initial ramdisk verification
3330 -120 common/image.c Ramdisk FIT image has incorrect format
3331 121 common/image.c Ramdisk FIT image has correct format
3332 122 common/image.c No ramdisk subimage unit name, using configuration
3333 -122 common/image.c Can't get configuration for ramdisk subimage
3334 123 common/image.c Ramdisk unit name specified
3335 -124 common/image.c Can't get ramdisk subimage node offset
3336 125 common/image.c Got ramdisk subimage node offset
3337 -125 common/image.c Ramdisk subimage hash verification failed
3338 126 common/image.c Ramdisk subimage hash verification OK
3339 -126 common/image.c Ramdisk subimage for unsupported architecture
3340 127 common/image.c Architecture check OK
3341 -127 common/image.c Can't get ramdisk subimage data/size
3342 128 common/image.c Got ramdisk subimage data/size
3343 129 common/image.c Can't get ramdisk load address
3344 -129 common/image.c Got ramdisk load address
3346 -130 common/cmd_doc.c Incorrect FIT image format
3347 131 common/cmd_doc.c FIT image format OK
3349 -140 common/cmd_ide.c Incorrect FIT image format
3350 141 common/cmd_ide.c FIT image format OK
3352 -150 common/cmd_nand.c Incorrect FIT image format
3353 151 common/cmd_nand.c FIT image format OK
3355 - legacy image format:
3356 CONFIG_IMAGE_FORMAT_LEGACY
3357 enables the legacy image format support in U-Boot.
3360 enabled if CONFIG_FIT_SIGNATURE is not defined.
3362 CONFIG_DISABLE_IMAGE_LEGACY
3363 disable the legacy image format
3365 This define is introduced, as the legacy image format is
3366 enabled per default for backward compatibility.
3368 - FIT image support:
3370 Enable support for the FIT uImage format.
3372 CONFIG_FIT_BEST_MATCH
3373 When no configuration is explicitly selected, default to the
3374 one whose fdt's compatibility field best matches that of
3375 U-Boot itself. A match is considered "best" if it matches the
3376 most specific compatibility entry of U-Boot's fdt's root node.
3377 The order of entries in the configuration's fdt is ignored.
3379 CONFIG_FIT_SIGNATURE
3380 This option enables signature verification of FIT uImages,
3381 using a hash signed and verified using RSA. If
3382 CONFIG_SHA_PROG_HW_ACCEL is defined, i.e support for progressive
3383 hashing is available using hardware, RSA library will use it.
3384 See doc/uImage.FIT/signature.txt for more details.
3386 WARNING: When relying on signed FIT images with required
3387 signature check the legacy image format is default
3388 disabled. If a board need legacy image format support
3389 enable this through CONFIG_IMAGE_FORMAT_LEGACY
3391 CONFIG_FIT_DISABLE_SHA256
3392 Supporting SHA256 hashes has quite an impact on binary size.
3393 For constrained systems sha256 hash support can be disabled
3396 - Standalone program support:
3397 CONFIG_STANDALONE_LOAD_ADDR
3399 This option defines a board specific value for the
3400 address where standalone program gets loaded, thus
3401 overwriting the architecture dependent default
3404 - Frame Buffer Address:
3407 Define CONFIG_FB_ADDR if you want to use specific
3408 address for frame buffer. This is typically the case
3409 when using a graphics controller has separate video
3410 memory. U-Boot will then place the frame buffer at
3411 the given address instead of dynamically reserving it
3412 in system RAM by calling lcd_setmem(), which grabs
3413 the memory for the frame buffer depending on the
3414 configured panel size.
3416 Please see board_init_f function.
3418 - Automatic software updates via TFTP server
3420 CONFIG_UPDATE_TFTP_CNT_MAX
3421 CONFIG_UPDATE_TFTP_MSEC_MAX
3423 These options enable and control the auto-update feature;
3424 for a more detailed description refer to doc/README.update.
3426 - MTD Support (mtdparts command, UBI support)
3429 Adds the MTD device infrastructure from the Linux kernel.
3430 Needed for mtdparts command support.
3432 CONFIG_MTD_PARTITIONS
3434 Adds the MTD partitioning infrastructure from the Linux
3435 kernel. Needed for UBI support.
3440 Adds commands for interacting with MTD partitions formatted
3441 with the UBI flash translation layer
3443 Requires also defining CONFIG_RBTREE
3445 CONFIG_UBI_SILENCE_MSG
3447 Make the verbose messages from UBI stop printing. This leaves
3448 warnings and errors enabled.
3451 CONFIG_MTD_UBI_WL_THRESHOLD
3452 This parameter defines the maximum difference between the highest
3453 erase counter value and the lowest erase counter value of eraseblocks
3454 of UBI devices. When this threshold is exceeded, UBI starts performing
3455 wear leveling by means of moving data from eraseblock with low erase
3456 counter to eraseblocks with high erase counter.
3458 The default value should be OK for SLC NAND flashes, NOR flashes and
3459 other flashes which have eraseblock life-cycle 100000 or more.
3460 However, in case of MLC NAND flashes which typically have eraseblock
3461 life-cycle less than 10000, the threshold should be lessened (e.g.,
3462 to 128 or 256, although it does not have to be power of 2).
3466 CONFIG_MTD_UBI_BEB_LIMIT
3467 This option specifies the maximum bad physical eraseblocks UBI
3468 expects on the MTD device (per 1024 eraseblocks). If the
3469 underlying flash does not admit of bad eraseblocks (e.g. NOR
3470 flash), this value is ignored.
3472 NAND datasheets often specify the minimum and maximum NVM
3473 (Number of Valid Blocks) for the flashes' endurance lifetime.
3474 The maximum expected bad eraseblocks per 1024 eraseblocks
3475 then can be calculated as "1024 * (1 - MinNVB / MaxNVB)",
3476 which gives 20 for most NANDs (MaxNVB is basically the total
3477 count of eraseblocks on the chip).
3479 To put it differently, if this value is 20, UBI will try to
3480 reserve about 1.9% of physical eraseblocks for bad blocks
3481 handling. And that will be 1.9% of eraseblocks on the entire
3482 NAND chip, not just the MTD partition UBI attaches. This means
3483 that if you have, say, a NAND flash chip admits maximum 40 bad
3484 eraseblocks, and it is split on two MTD partitions of the same
3485 size, UBI will reserve 40 eraseblocks when attaching a
3490 CONFIG_MTD_UBI_FASTMAP
3491 Fastmap is a mechanism which allows attaching an UBI device
3492 in nearly constant time. Instead of scanning the whole MTD device it
3493 only has to locate a checkpoint (called fastmap) on the device.
3494 The on-flash fastmap contains all information needed to attach
3495 the device. Using fastmap makes only sense on large devices where
3496 attaching by scanning takes long. UBI will not automatically install
3497 a fastmap on old images, but you can set the UBI parameter
3498 CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT to 1 if you want so. Please note
3499 that fastmap-enabled images are still usable with UBI implementations
3500 without fastmap support. On typical flash devices the whole fastmap
3501 fits into one PEB. UBI will reserve PEBs to hold two fastmaps.
3503 CONFIG_MTD_UBI_FASTMAP_AUTOCONVERT
3504 Set this parameter to enable fastmap automatically on images
3511 Adds commands for interacting with UBI volumes formatted as
3512 UBIFS. UBIFS is read-only in u-boot.
3514 Requires UBI support as well as CONFIG_LZO
3516 CONFIG_UBIFS_SILENCE_MSG
3518 Make the verbose messages from UBIFS stop printing. This leaves
3519 warnings and errors enabled.
3523 Enable building of SPL globally.
3526 LDSCRIPT for linking the SPL binary.
3528 CONFIG_SPL_MAX_FOOTPRINT
3529 Maximum size in memory allocated to the SPL, BSS included.
3530 When defined, the linker checks that the actual memory
3531 used by SPL from _start to __bss_end does not exceed it.
3532 CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
3533 must not be both defined at the same time.
3536 Maximum size of the SPL image (text, data, rodata, and
3537 linker lists sections), BSS excluded.
3538 When defined, the linker checks that the actual size does
3541 CONFIG_SPL_TEXT_BASE
3542 TEXT_BASE for linking the SPL binary.
3544 CONFIG_SPL_RELOC_TEXT_BASE
3545 Address to relocate to. If unspecified, this is equal to
3546 CONFIG_SPL_TEXT_BASE (i.e. no relocation is done).
3548 CONFIG_SPL_BSS_START_ADDR
3549 Link address for the BSS within the SPL binary.
3551 CONFIG_SPL_BSS_MAX_SIZE
3552 Maximum size in memory allocated to the SPL BSS.
3553 When defined, the linker checks that the actual memory used
3554 by SPL from __bss_start to __bss_end does not exceed it.
3555 CONFIG_SPL_MAX_FOOTPRINT and CONFIG_SPL_BSS_MAX_SIZE
3556 must not be both defined at the same time.
3559 Adress of the start of the stack SPL will use
3561 CONFIG_SPL_PANIC_ON_RAW_IMAGE
3562 When defined, SPL will panic() if the image it has
3563 loaded does not have a signature.
3564 Defining this is useful when code which loads images
3565 in SPL cannot guarantee that absolutely all read errors
3567 An example is the LPC32XX MLC NAND driver, which will
3568 consider that a completely unreadable NAND block is bad,
3569 and thus should be skipped silently.
3571 CONFIG_SPL_RELOC_STACK
3572 Adress of the start of the stack SPL will use after
3573 relocation. If unspecified, this is equal to
3576 CONFIG_SYS_SPL_MALLOC_START
3577 Starting address of the malloc pool used in SPL.
3579 CONFIG_SYS_SPL_MALLOC_SIZE
3580 The size of the malloc pool used in SPL.
3582 CONFIG_SPL_FRAMEWORK
3583 Enable the SPL framework under common/. This framework
3584 supports MMC, NAND and YMODEM loading of U-Boot and NAND
3585 NAND loading of the Linux Kernel.
3588 Enable booting directly to an OS from SPL.
3589 See also: doc/README.falcon
3591 CONFIG_SPL_DISPLAY_PRINT
3592 For ARM, enable an optional function to print more information
3593 about the running system.
3595 CONFIG_SPL_INIT_MINIMAL
3596 Arch init code should be built for a very small image
3598 CONFIG_SPL_LIBCOMMON_SUPPORT
3599 Support for common/libcommon.o in SPL binary
3601 CONFIG_SPL_LIBDISK_SUPPORT
3602 Support for disk/libdisk.o in SPL binary
3604 CONFIG_SPL_I2C_SUPPORT
3605 Support for drivers/i2c/libi2c.o in SPL binary
3607 CONFIG_SPL_GPIO_SUPPORT
3608 Support for drivers/gpio/libgpio.o in SPL binary
3610 CONFIG_SPL_MMC_SUPPORT
3611 Support for drivers/mmc/libmmc.o in SPL binary
3613 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR,
3614 CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS,
3615 Address and partition on the MMC to load U-Boot from
3616 when the MMC is being used in raw mode.
3618 CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
3619 Partition on the MMC to load U-Boot from when the MMC is being
3622 CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR
3623 Sector to load kernel uImage from when MMC is being
3624 used in raw mode (for Falcon mode)
3626 CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR,
3627 CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS
3628 Sector and number of sectors to load kernel argument
3629 parameters from when MMC is being used in raw mode
3632 CONFIG_SYS_MMCSD_FS_BOOT_PARTITION
3633 Partition on the MMC to load U-Boot from when the MMC is being
3636 CONFIG_SPL_FAT_SUPPORT
3637 Support for fs/fat/libfat.o in SPL binary
3639 CONFIG_SPL_EXT_SUPPORT
3640 Support for EXT filesystem in SPL binary
3642 CONFIG_SPL_FS_LOAD_PAYLOAD_NAME
3643 Filename to read to load U-Boot when reading from filesystem
3645 CONFIG_SPL_FS_LOAD_KERNEL_NAME
3646 Filename to read to load kernel uImage when reading
3647 from filesystem (for Falcon mode)
3649 CONFIG_SPL_FS_LOAD_ARGS_NAME
3650 Filename to read to load kernel argument parameters
3651 when reading from filesystem (for Falcon mode)
3653 CONFIG_SPL_MPC83XX_WAIT_FOR_NAND
3654 Set this for NAND SPL on PPC mpc83xx targets, so that
3655 start.S waits for the rest of the SPL to load before
3656 continuing (the hardware starts execution after just
3657 loading the first page rather than the full 4K).
3659 CONFIG_SPL_SKIP_RELOCATE
3660 Avoid SPL relocation
3662 CONFIG_SPL_NAND_BASE
3663 Include nand_base.c in the SPL. Requires
3664 CONFIG_SPL_NAND_DRIVERS.
3666 CONFIG_SPL_NAND_DRIVERS
3667 SPL uses normal NAND drivers, not minimal drivers.
3670 Include standard software ECC in the SPL
3672 CONFIG_SPL_NAND_SIMPLE
3673 Support for NAND boot using simple NAND drivers that
3674 expose the cmd_ctrl() interface.
3676 CONFIG_SPL_MTD_SUPPORT
3677 Support for the MTD subsystem within SPL. Useful for
3678 environment on NAND support within SPL.
3680 CONFIG_SPL_NAND_RAW_ONLY
3681 Support to boot only raw u-boot.bin images. Use this only
3682 if you need to save space.
3684 CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
3685 Set for the SPL on PPC mpc8xxx targets, support for
3686 drivers/ddr/fsl/libddr.o in SPL binary.
3688 CONFIG_SPL_COMMON_INIT_DDR
3689 Set for common ddr init with serial presence detect in
3692 CONFIG_SYS_NAND_5_ADDR_CYCLE, CONFIG_SYS_NAND_PAGE_COUNT,
3693 CONFIG_SYS_NAND_PAGE_SIZE, CONFIG_SYS_NAND_OOBSIZE,
3694 CONFIG_SYS_NAND_BLOCK_SIZE, CONFIG_SYS_NAND_BAD_BLOCK_POS,
3695 CONFIG_SYS_NAND_ECCPOS, CONFIG_SYS_NAND_ECCSIZE,
3696 CONFIG_SYS_NAND_ECCBYTES
3697 Defines the size and behavior of the NAND that SPL uses
3700 CONFIG_SPL_NAND_BOOT
3701 Add support NAND boot
3703 CONFIG_SYS_NAND_U_BOOT_OFFS
3704 Location in NAND to read U-Boot from
3706 CONFIG_SYS_NAND_U_BOOT_DST
3707 Location in memory to load U-Boot to
3709 CONFIG_SYS_NAND_U_BOOT_SIZE
3710 Size of image to load
3712 CONFIG_SYS_NAND_U_BOOT_START
3713 Entry point in loaded image to jump to
3715 CONFIG_SYS_NAND_HW_ECC_OOBFIRST
3716 Define this if you need to first read the OOB and then the
3717 data. This is used, for example, on davinci platforms.
3719 CONFIG_SPL_OMAP3_ID_NAND
3720 Support for an OMAP3-specific set of functions to return the
3721 ID and MFR of the first attached NAND chip, if present.
3723 CONFIG_SPL_SERIAL_SUPPORT
3724 Support for drivers/serial/libserial.o in SPL binary
3726 CONFIG_SPL_SPI_FLASH_SUPPORT
3727 Support for drivers/mtd/spi/libspi_flash.o in SPL binary
3729 CONFIG_SPL_SPI_SUPPORT
3730 Support for drivers/spi/libspi.o in SPL binary
3732 CONFIG_SPL_RAM_DEVICE
3733 Support for running image already present in ram, in SPL binary
3735 CONFIG_SPL_LIBGENERIC_SUPPORT
3736 Support for lib/libgeneric.o in SPL binary
3738 CONFIG_SPL_ENV_SUPPORT
3739 Support for the environment operating in SPL binary
3741 CONFIG_SPL_NET_SUPPORT
3742 Support for the net/libnet.o in SPL binary.
3743 It conflicts with SPL env from storage medium specified by
3744 CONFIG_ENV_IS_xxx but CONFIG_ENV_IS_NOWHERE
3747 Image offset to which the SPL should be padded before appending
3748 the SPL payload. By default, this is defined as
3749 CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
3750 CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
3751 payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
3754 Final target image containing SPL and payload. Some SPLs
3755 use an arch-specific makefile fragment instead, for
3756 example if more than one image needs to be produced.
3758 CONFIG_FIT_SPL_PRINT
3759 Printing information about a FIT image adds quite a bit of
3760 code to SPL. So this is normally disabled in SPL. Use this
3761 option to re-enable it. This will affect the output of the
3762 bootm command when booting a FIT image.
3766 Enable building of TPL globally.
3769 Image offset to which the TPL should be padded before appending
3770 the TPL payload. By default, this is defined as
3771 CONFIG_SPL_MAX_SIZE, or 0 if CONFIG_SPL_MAX_SIZE is undefined.
3772 CONFIG_SPL_PAD_TO must be either 0, meaning to append the SPL
3773 payload without any padding, or >= CONFIG_SPL_MAX_SIZE.
3778 [so far only for SMDK2400 boards]
3780 - Modem support enable:
3781 CONFIG_MODEM_SUPPORT
3783 - RTS/CTS Flow control enable:
3786 - Modem debug support:
3787 CONFIG_MODEM_SUPPORT_DEBUG
3789 Enables debugging stuff (char screen[1024], dbg())
3790 for modem support. Useful only with BDI2000.
3792 - Interrupt support (PPC):
3794 There are common interrupt_init() and timer_interrupt()
3795 for all PPC archs. interrupt_init() calls interrupt_init_cpu()
3796 for CPU specific initialization. interrupt_init_cpu()
3797 should set decrementer_count to appropriate value. If
3798 CPU resets decrementer automatically after interrupt
3799 (ppc4xx) it should set decrementer_count to zero.
3800 timer_interrupt() calls timer_interrupt_cpu() for CPU
3801 specific handling. If board has watchdog / status_led
3802 / other_activity_monitor it works automatically from
3803 general timer_interrupt().
3807 In the target system modem support is enabled when a
3808 specific key (key combination) is pressed during
3809 power-on. Otherwise U-Boot will boot normally
3810 (autoboot). The key_pressed() function is called from
3811 board_init(). Currently key_pressed() is a dummy
3812 function, returning 1 and thus enabling modem
3815 If there are no modem init strings in the
3816 environment, U-Boot proceed to autoboot; the
3817 previous output (banner, info printfs) will be
3820 See also: doc/README.Modem
3822 Board initialization settings:
3823 ------------------------------
3825 During Initialization u-boot calls a number of board specific functions
3826 to allow the preparation of board specific prerequisites, e.g. pin setup
3827 before drivers are initialized. To enable these callbacks the
3828 following configuration macros have to be defined. Currently this is
3829 architecture specific, so please check arch/your_architecture/lib/board.c
3830 typically in board_init_f() and board_init_r().
3832 - CONFIG_BOARD_EARLY_INIT_F: Call board_early_init_f()
3833 - CONFIG_BOARD_EARLY_INIT_R: Call board_early_init_r()
3834 - CONFIG_BOARD_LATE_INIT: Call board_late_init()
3835 - CONFIG_BOARD_POSTCLK_INIT: Call board_postclk_init()
3837 Configuration Settings:
3838 -----------------------
3840 - CONFIG_SYS_SUPPORT_64BIT_DATA: Defined automatically if compiled as 64-bit.
3841 Optionally it can be defined to support 64-bit memory commands.
3843 - CONFIG_SYS_LONGHELP: Defined when you want long help messages included;
3844 undefine this when you're short of memory.
3846 - CONFIG_SYS_HELP_CMD_WIDTH: Defined when you want to override the default
3847 width of the commands listed in the 'help' command output.
3849 - CONFIG_SYS_PROMPT: This is what U-Boot prints on the console to
3850 prompt for user input.
3852 - CONFIG_SYS_CBSIZE: Buffer size for input from the Console
3854 - CONFIG_SYS_PBSIZE: Buffer size for Console output
3856 - CONFIG_SYS_MAXARGS: max. Number of arguments accepted for monitor commands
3858 - CONFIG_SYS_BARGSIZE: Buffer size for Boot Arguments which are passed to
3859 the application (usually a Linux kernel) when it is
3862 - CONFIG_SYS_BAUDRATE_TABLE:
3863 List of legal baudrate settings for this board.
3865 - CONFIG_SYS_CONSOLE_INFO_QUIET
3866 Suppress display of console information at boot.
3868 - CONFIG_SYS_CONSOLE_IS_IN_ENV
3869 If the board specific function
3870 extern int overwrite_console (void);
3871 returns 1, the stdin, stderr and stdout are switched to the
3872 serial port, else the settings in the environment are used.
3874 - CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
3875 Enable the call to overwrite_console().
3877 - CONFIG_SYS_CONSOLE_ENV_OVERWRITE
3878 Enable overwrite of previous console environment settings.
3880 - CONFIG_SYS_MEMTEST_START, CONFIG_SYS_MEMTEST_END:
3881 Begin and End addresses of the area used by the
3884 - CONFIG_SYS_ALT_MEMTEST:
3885 Enable an alternate, more extensive memory test.
3887 - CONFIG_SYS_MEMTEST_SCRATCH:
3888 Scratch address used by the alternate memory test
3889 You only need to set this if address zero isn't writeable
3891 - CONFIG_SYS_MEM_TOP_HIDE (PPC only):
3892 If CONFIG_SYS_MEM_TOP_HIDE is defined in the board config header,
3893 this specified memory area will get subtracted from the top
3894 (end) of RAM and won't get "touched" at all by U-Boot. By
3895 fixing up gd->ram_size the Linux kernel should gets passed
3896 the now "corrected" memory size and won't touch it either.
3897 This should work for arch/ppc and arch/powerpc. Only Linux
3898 board ports in arch/powerpc with bootwrapper support that
3899 recalculate the memory size from the SDRAM controller setup
3900 will have to get fixed in Linux additionally.
3902 This option can be used as a workaround for the 440EPx/GRx
3903 CHIP 11 errata where the last 256 bytes in SDRAM shouldn't
3906 WARNING: Please make sure that this value is a multiple of
3907 the Linux page size (normally 4k). If this is not the case,
3908 then the end address of the Linux memory will be located at a
3909 non page size aligned address and this could cause major
3912 - CONFIG_SYS_LOADS_BAUD_CHANGE:
3913 Enable temporary baudrate change while serial download
3915 - CONFIG_SYS_SDRAM_BASE:
3916 Physical start address of SDRAM. _Must_ be 0 here.
3918 - CONFIG_SYS_MBIO_BASE:
3919 Physical start address of Motherboard I/O (if using a
3922 - CONFIG_SYS_FLASH_BASE:
3923 Physical start address of Flash memory.
3925 - CONFIG_SYS_MONITOR_BASE:
3926 Physical start address of boot monitor code (set by
3927 make config files to be same as the text base address
3928 (CONFIG_SYS_TEXT_BASE) used when linking) - same as
3929 CONFIG_SYS_FLASH_BASE when booting from flash.
3931 - CONFIG_SYS_MONITOR_LEN:
3932 Size of memory reserved for monitor code, used to
3933 determine _at_compile_time_ (!) if the environment is
3934 embedded within the U-Boot image, or in a separate
3937 - CONFIG_SYS_MALLOC_LEN:
3938 Size of DRAM reserved for malloc() use.
3940 - CONFIG_SYS_MALLOC_F_LEN
3941 Size of the malloc() pool for use before relocation. If
3942 this is defined, then a very simple malloc() implementation
3943 will become available before relocation. The address is just
3944 below the global data, and the stack is moved down to make
3947 This feature allocates regions with increasing addresses
3948 within the region. calloc() is supported, but realloc()
3949 is not available. free() is supported but does nothing.
3950 The memory will be freed (or in fact just forgotten) when
3951 U-Boot relocates itself.
3953 Pre-relocation malloc() is only supported on ARM and sandbox
3954 at present but is fairly easy to enable for other archs.
3956 - CONFIG_SYS_MALLOC_SIMPLE
3957 Provides a simple and small malloc() and calloc() for those
3958 boards which do not use the full malloc in SPL (which is
3959 enabled with CONFIG_SYS_SPL_MALLOC_START).
3961 - CONFIG_SYS_NONCACHED_MEMORY:
3962 Size of non-cached memory area. This area of memory will be
3963 typically located right below the malloc() area and mapped
3964 uncached in the MMU. This is useful for drivers that would
3965 otherwise require a lot of explicit cache maintenance. For
3966 some drivers it's also impossible to properly maintain the
3967 cache. For example if the regions that need to be flushed
3968 are not a multiple of the cache-line size, *and* padding
3969 cannot be allocated between the regions to align them (i.e.
3970 if the HW requires a contiguous array of regions, and the
3971 size of each region is not cache-aligned), then a flush of
3972 one region may result in overwriting data that hardware has
3973 written to another region in the same cache-line. This can
3974 happen for example in network drivers where descriptors for
3975 buffers are typically smaller than the CPU cache-line (e.g.
3976 16 bytes vs. 32 or 64 bytes).
3978 Non-cached memory is only supported on 32-bit ARM at present.
3980 - CONFIG_SYS_BOOTM_LEN:
3981 Normally compressed uImages are limited to an
3982 uncompressed size of 8 MBytes. If this is not enough,
3983 you can define CONFIG_SYS_BOOTM_LEN in your board config file
3984 to adjust this setting to your needs.
3986 - CONFIG_SYS_BOOTMAPSZ:
3987 Maximum size of memory mapped by the startup code of
3988 the Linux kernel; all data that must be processed by
3989 the Linux kernel (bd_info, boot arguments, FDT blob if
3990 used) must be put below this limit, unless "bootm_low"
3991 environment variable is defined and non-zero. In such case
3992 all data for the Linux kernel must be between "bootm_low"
3993 and "bootm_low" + CONFIG_SYS_BOOTMAPSZ. The environment
3994 variable "bootm_mapsize" will override the value of
3995 CONFIG_SYS_BOOTMAPSZ. If CONFIG_SYS_BOOTMAPSZ is undefined,
3996 then the value in "bootm_size" will be used instead.
3998 - CONFIG_SYS_BOOT_RAMDISK_HIGH:
3999 Enable initrd_high functionality. If defined then the
4000 initrd_high feature is enabled and the bootm ramdisk subcommand
4003 - CONFIG_SYS_BOOT_GET_CMDLINE:
4004 Enables allocating and saving kernel cmdline in space between
4005 "bootm_low" and "bootm_low" + BOOTMAPSZ.
4007 - CONFIG_SYS_BOOT_GET_KBD:
4008 Enables allocating and saving a kernel copy of the bd_info in
4009 space between "bootm_low" and "bootm_low" + BOOTMAPSZ.
4011 - CONFIG_SYS_MAX_FLASH_BANKS:
4012 Max number of Flash memory banks
4014 - CONFIG_SYS_MAX_FLASH_SECT:
4015 Max number of sectors on a Flash chip
4017 - CONFIG_SYS_FLASH_ERASE_TOUT:
4018 Timeout for Flash erase operations (in ms)
4020 - CONFIG_SYS_FLASH_WRITE_TOUT:
4021 Timeout for Flash write operations (in ms)
4023 - CONFIG_SYS_FLASH_LOCK_TOUT
4024 Timeout for Flash set sector lock bit operation (in ms)
4026 - CONFIG_SYS_FLASH_UNLOCK_TOUT
4027 Timeout for Flash clear lock bits operation (in ms)
4029 - CONFIG_SYS_FLASH_PROTECTION
4030 If defined, hardware flash sectors protection is used
4031 instead of U-Boot software protection.
4033 - CONFIG_SYS_DIRECT_FLASH_TFTP:
4035 Enable TFTP transfers directly to flash memory;
4036 without this option such a download has to be
4037 performed in two steps: (1) download to RAM, and (2)
4038 copy from RAM to flash.
4040 The two-step approach is usually more reliable, since
4041 you can check if the download worked before you erase
4042 the flash, but in some situations (when system RAM is
4043 too limited to allow for a temporary copy of the
4044 downloaded image) this option may be very useful.
4046 - CONFIG_SYS_FLASH_CFI:
4047 Define if the flash driver uses extra elements in the
4048 common flash structure for storing flash geometry.
4050 - CONFIG_FLASH_CFI_DRIVER
4051 This option also enables the building of the cfi_flash driver
4052 in the drivers directory
4054 - CONFIG_FLASH_CFI_MTD
4055 This option enables the building of the cfi_mtd driver
4056 in the drivers directory. The driver exports CFI flash
4059 - CONFIG_SYS_FLASH_USE_BUFFER_WRITE
4060 Use buffered writes to flash.
4062 - CONFIG_FLASH_SPANSION_S29WS_N
4063 s29ws-n MirrorBit flash has non-standard addresses for buffered
4066 - CONFIG_SYS_FLASH_QUIET_TEST
4067 If this option is defined, the common CFI flash doesn't
4068 print it's warning upon not recognized FLASH banks. This
4069 is useful, if some of the configured banks are only
4070 optionally available.
4072 - CONFIG_FLASH_SHOW_PROGRESS
4073 If defined (must be an integer), print out countdown
4074 digits and dots. Recommended value: 45 (9..1) for 80
4075 column displays, 15 (3..1) for 40 column displays.
4077 - CONFIG_FLASH_VERIFY
4078 If defined, the content of the flash (destination) is compared
4079 against the source after the write operation. An error message
4080 will be printed when the contents are not identical.
4081 Please note that this option is useless in nearly all cases,
4082 since such flash programming errors usually are detected earlier
4083 while unprotecting/erasing/programming. Please only enable
4084 this option if you really know what you are doing.
4086 - CONFIG_SYS_RX_ETH_BUFFER:
4087 Defines the number of Ethernet receive buffers. On some
4088 Ethernet controllers it is recommended to set this value
4089 to 8 or even higher (EEPRO100 or 405 EMAC), since all
4090 buffers can be full shortly after enabling the interface
4091 on high Ethernet traffic.
4092 Defaults to 4 if not defined.
4094 - CONFIG_ENV_MAX_ENTRIES
4096 Maximum number of entries in the hash table that is used
4097 internally to store the environment settings. The default
4098 setting is supposed to be generous and should work in most
4099 cases. This setting can be used to tune behaviour; see
4100 lib/hashtable.c for details.
4102 - CONFIG_ENV_FLAGS_LIST_DEFAULT
4103 - CONFIG_ENV_FLAGS_LIST_STATIC
4104 Enable validation of the values given to environment variables when
4105 calling env set. Variables can be restricted to only decimal,
4106 hexadecimal, or boolean. If CONFIG_CMD_NET is also defined,
4107 the variables can also be restricted to IP address or MAC address.
4109 The format of the list is:
4110 type_attribute = [s|d|x|b|i|m]
4111 access_attribute = [a|r|o|c]
4112 attributes = type_attribute[access_attribute]
4113 entry = variable_name[:attributes]
4116 The type attributes are:
4117 s - String (default)
4120 b - Boolean ([1yYtT|0nNfF])
4124 The access attributes are:
4130 - CONFIG_ENV_FLAGS_LIST_DEFAULT
4131 Define this to a list (string) to define the ".flags"
4132 environment variable in the default or embedded environment.
4134 - CONFIG_ENV_FLAGS_LIST_STATIC
4135 Define this to a list (string) to define validation that
4136 should be done if an entry is not found in the ".flags"
4137 environment variable. To override a setting in the static
4138 list, simply add an entry for the same variable name to the
4141 - CONFIG_ENV_ACCESS_IGNORE_FORCE
4142 If defined, don't allow the -f switch to env set override variable
4145 - CONFIG_SYS_GENERIC_BOARD
4146 This selects the architecture-generic board system instead of the
4147 architecture-specific board files. It is intended to move boards
4148 to this new framework over time. Defining this will disable the
4149 arch/foo/lib/board.c file and use common/board_f.c and
4150 common/board_r.c instead. To use this option your architecture
4151 must support it (i.e. must select HAVE_GENERIC_BOARD in arch/Kconfig).
4152 If you find problems enabling this option on your board please report
4153 the problem and send patches!
4155 - CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC (OMAP only)
4156 This is set by OMAP boards for the max time that reset should
4157 be asserted. See doc/README.omap-reset-time for details on how
4158 the value can be calculated on a given board.
4161 If stdint.h is available with your toolchain you can define this
4162 option to enable it. You can provide option 'USE_STDINT=1' when
4163 building U-Boot to enable this.
4165 The following definitions that deal with the placement and management
4166 of environment data (variable area); in general, we support the
4167 following configurations:
4169 - CONFIG_BUILD_ENVCRC:
4171 Builds up envcrc with the target environment so that external utils
4172 may easily extract it and embed it in final U-Boot images.
4174 - CONFIG_ENV_IS_IN_FLASH:
4176 Define this if the environment is in flash memory.
4178 a) The environment occupies one whole flash sector, which is
4179 "embedded" in the text segment with the U-Boot code. This
4180 happens usually with "bottom boot sector" or "top boot
4181 sector" type flash chips, which have several smaller
4182 sectors at the start or the end. For instance, such a
4183 layout can have sector sizes of 8, 2x4, 16, Nx32 kB. In
4184 such a case you would place the environment in one of the
4185 4 kB sectors - with U-Boot code before and after it. With
4186 "top boot sector" type flash chips, you would put the
4187 environment in one of the last sectors, leaving a gap
4188 between U-Boot and the environment.
4190 - CONFIG_ENV_OFFSET:
4192 Offset of environment data (variable area) to the
4193 beginning of flash memory; for instance, with bottom boot
4194 type flash chips the second sector can be used: the offset
4195 for this sector is given here.
4197 CONFIG_ENV_OFFSET is used relative to CONFIG_SYS_FLASH_BASE.
4201 This is just another way to specify the start address of
4202 the flash sector containing the environment (instead of
4205 - CONFIG_ENV_SECT_SIZE:
4207 Size of the sector containing the environment.
4210 b) Sometimes flash chips have few, equal sized, BIG sectors.
4211 In such a case you don't want to spend a whole sector for
4216 If you use this in combination with CONFIG_ENV_IS_IN_FLASH
4217 and CONFIG_ENV_SECT_SIZE, you can specify to use only a part
4218 of this flash sector for the environment. This saves
4219 memory for the RAM copy of the environment.
4221 It may also save flash memory if you decide to use this
4222 when your environment is "embedded" within U-Boot code,
4223 since then the remainder of the flash sector could be used
4224 for U-Boot code. It should be pointed out that this is
4225 STRONGLY DISCOURAGED from a robustness point of view:
4226 updating the environment in flash makes it always
4227 necessary to erase the WHOLE sector. If something goes
4228 wrong before the contents has been restored from a copy in
4229 RAM, your target system will be dead.
4231 - CONFIG_ENV_ADDR_REDUND
4232 CONFIG_ENV_SIZE_REDUND
4234 These settings describe a second storage area used to hold
4235 a redundant copy of the environment data, so that there is
4236 a valid backup copy in case there is a power failure during
4237 a "saveenv" operation.
4239 BE CAREFUL! Any changes to the flash layout, and some changes to the
4240 source code will make it necessary to adapt <board>/u-boot.lds*
4244 - CONFIG_ENV_IS_IN_NVRAM:
4246 Define this if you have some non-volatile memory device
4247 (NVRAM, battery buffered SRAM) which you want to use for the
4253 These two #defines are used to determine the memory area you
4254 want to use for environment. It is assumed that this memory
4255 can just be read and written to, without any special
4258 BE CAREFUL! The first access to the environment happens quite early
4259 in U-Boot initialization (when we try to get the setting of for the
4260 console baudrate). You *MUST* have mapped your NVRAM area then, or
4263 Please note that even with NVRAM we still use a copy of the
4264 environment in RAM: we could work on NVRAM directly, but we want to
4265 keep settings there always unmodified except somebody uses "saveenv"
4266 to save the current settings.
4269 - CONFIG_ENV_IS_IN_EEPROM:
4271 Use this if you have an EEPROM or similar serial access
4272 device and a driver for it.
4274 - CONFIG_ENV_OFFSET:
4277 These two #defines specify the offset and size of the
4278 environment area within the total memory of your EEPROM.
4280 - CONFIG_SYS_I2C_EEPROM_ADDR:
4281 If defined, specified the chip address of the EEPROM device.
4282 The default address is zero.
4284 - CONFIG_SYS_I2C_EEPROM_BUS:
4285 If defined, specified the i2c bus of the EEPROM device.
4287 - CONFIG_SYS_EEPROM_PAGE_WRITE_BITS:
4288 If defined, the number of bits used to address bytes in a
4289 single page in the EEPROM device. A 64 byte page, for example
4290 would require six bits.
4292 - CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS:
4293 If defined, the number of milliseconds to delay between
4294 page writes. The default is zero milliseconds.
4296 - CONFIG_SYS_I2C_EEPROM_ADDR_LEN:
4297 The length in bytes of the EEPROM memory array address. Note
4298 that this is NOT the chip address length!
4300 - CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW:
4301 EEPROM chips that implement "address overflow" are ones
4302 like Catalyst 24WC04/08/16 which has 9/10/11 bits of
4303 address and the extra bits end up in the "chip address" bit
4304 slots. This makes a 24WC08 (1Kbyte) chip look like four 256
4307 Note that we consider the length of the address field to
4308 still be one byte because the extra address bits are hidden
4309 in the chip address.
4311 - CONFIG_SYS_EEPROM_SIZE:
4312 The size in bytes of the EEPROM device.
4314 - CONFIG_ENV_EEPROM_IS_ON_I2C
4315 define this, if you have I2C and SPI activated, and your
4316 EEPROM, which holds the environment, is on the I2C bus.
4318 - CONFIG_I2C_ENV_EEPROM_BUS
4319 if you have an Environment on an EEPROM reached over
4320 I2C muxes, you can define here, how to reach this
4321 EEPROM. For example:
4323 #define CONFIG_I2C_ENV_EEPROM_BUS 1
4325 EEPROM which holds the environment, is reached over
4326 a pca9547 i2c mux with address 0x70, channel 3.
4328 - CONFIG_ENV_IS_IN_DATAFLASH:
4330 Define this if you have a DataFlash memory device which you
4331 want to use for the environment.
4333 - CONFIG_ENV_OFFSET:
4337 These three #defines specify the offset and size of the
4338 environment area within the total memory of your DataFlash placed
4339 at the specified address.
4341 - CONFIG_ENV_IS_IN_SPI_FLASH:
4343 Define this if you have a SPI Flash memory device which you
4344 want to use for the environment.
4346 - CONFIG_ENV_OFFSET:
4349 These two #defines specify the offset and size of the
4350 environment area within the SPI Flash. CONFIG_ENV_OFFSET must be
4351 aligned to an erase sector boundary.
4353 - CONFIG_ENV_SECT_SIZE:
4355 Define the SPI flash's sector size.
4357 - CONFIG_ENV_OFFSET_REDUND (optional):
4359 This setting describes a second storage area of CONFIG_ENV_SIZE
4360 size used to hold a redundant copy of the environment data, so
4361 that there is a valid backup copy in case there is a power failure
4362 during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
4363 aligned to an erase sector boundary.
4365 - CONFIG_ENV_SPI_BUS (optional):
4366 - CONFIG_ENV_SPI_CS (optional):
4368 Define the SPI bus and chip select. If not defined they will be 0.
4370 - CONFIG_ENV_SPI_MAX_HZ (optional):
4372 Define the SPI max work clock. If not defined then use 1MHz.
4374 - CONFIG_ENV_SPI_MODE (optional):
4376 Define the SPI work mode. If not defined then use SPI_MODE_3.
4378 - CONFIG_ENV_IS_IN_REMOTE:
4380 Define this if you have a remote memory space which you
4381 want to use for the local device's environment.
4386 These two #defines specify the address and size of the
4387 environment area within the remote memory space. The
4388 local device can get the environment from remote memory
4389 space by SRIO or PCIE links.
4391 BE CAREFUL! For some special cases, the local device can not use
4392 "saveenv" command. For example, the local device will get the
4393 environment stored in a remote NOR flash by SRIO or PCIE link,
4394 but it can not erase, write this NOR flash by SRIO or PCIE interface.
4396 - CONFIG_ENV_IS_IN_NAND:
4398 Define this if you have a NAND device which you want to use
4399 for the environment.
4401 - CONFIG_ENV_OFFSET:
4404 These two #defines specify the offset and size of the environment
4405 area within the first NAND device. CONFIG_ENV_OFFSET must be
4406 aligned to an erase block boundary.
4408 - CONFIG_ENV_OFFSET_REDUND (optional):
4410 This setting describes a second storage area of CONFIG_ENV_SIZE
4411 size used to hold a redundant copy of the environment data, so
4412 that there is a valid backup copy in case there is a power failure
4413 during a "saveenv" operation. CONFIG_ENV_OFFSET_RENDUND must be
4414 aligned to an erase block boundary.
4416 - CONFIG_ENV_RANGE (optional):
4418 Specifies the length of the region in which the environment
4419 can be written. This should be a multiple of the NAND device's
4420 block size. Specifying a range with more erase blocks than
4421 are needed to hold CONFIG_ENV_SIZE allows bad blocks within
4422 the range to be avoided.
4424 - CONFIG_ENV_OFFSET_OOB (optional):
4426 Enables support for dynamically retrieving the offset of the
4427 environment from block zero's out-of-band data. The
4428 "nand env.oob" command can be used to record this offset.
4429 Currently, CONFIG_ENV_OFFSET_REDUND is not supported when
4430 using CONFIG_ENV_OFFSET_OOB.
4432 - CONFIG_NAND_ENV_DST
4434 Defines address in RAM to which the nand_spl code should copy the
4435 environment. If redundant environment is used, it will be copied to
4436 CONFIG_NAND_ENV_DST + CONFIG_ENV_SIZE.
4438 - CONFIG_ENV_IS_IN_UBI:
4440 Define this if you have an UBI volume that you want to use for the
4441 environment. This has the benefit of wear-leveling the environment
4442 accesses, which is important on NAND.
4444 - CONFIG_ENV_UBI_PART:
4446 Define this to a string that is the mtd partition containing the UBI.
4448 - CONFIG_ENV_UBI_VOLUME:
4450 Define this to the name of the volume that you want to store the
4453 - CONFIG_ENV_UBI_VOLUME_REDUND:
4455 Define this to the name of another volume to store a second copy of
4456 the environment in. This will enable redundant environments in UBI.
4457 It is assumed that both volumes are in the same MTD partition.
4459 - CONFIG_UBI_SILENCE_MSG
4460 - CONFIG_UBIFS_SILENCE_MSG
4462 You will probably want to define these to avoid a really noisy system
4463 when storing the env in UBI.
4465 - CONFIG_ENV_IS_IN_FAT:
4466 Define this if you want to use the FAT file system for the environment.
4468 - FAT_ENV_INTERFACE:
4470 Define this to a string that is the name of the block device.
4472 - FAT_ENV_DEV_AND_PART:
4474 Define this to a string to specify the partition of the device. It can
4477 "D:P", "D:0", "D", "D:" or "D:auto" (D, P are integers. And P >= 1)
4478 - "D:P": device D partition P. Error occurs if device D has no
4481 - "D" or "D:": device D partition 1 if device D has partition
4482 table, or the whole device D if has no partition
4484 - "D:auto": first partition in device D with bootable flag set.
4485 If none, first valid partition in device D. If no
4486 partition table then means device D.
4490 It's a string of the FAT file name. This file use to store the
4494 This should be defined. Otherwise it cannot save the environment file.
4496 - CONFIG_ENV_IS_IN_MMC:
4498 Define this if you have an MMC device which you want to use for the
4501 - CONFIG_SYS_MMC_ENV_DEV:
4503 Specifies which MMC device the environment is stored in.
4505 - CONFIG_SYS_MMC_ENV_PART (optional):
4507 Specifies which MMC partition the environment is stored in. If not
4508 set, defaults to partition 0, the user area. Common values might be
4509 1 (first MMC boot partition), 2 (second MMC boot partition).
4511 - CONFIG_ENV_OFFSET:
4514 These two #defines specify the offset and size of the environment
4515 area within the specified MMC device.
4517 If offset is positive (the usual case), it is treated as relative to
4518 the start of the MMC partition. If offset is negative, it is treated
4519 as relative to the end of the MMC partition. This can be useful if
4520 your board may be fitted with different MMC devices, which have
4521 different sizes for the MMC partitions, and you always want the
4522 environment placed at the very end of the partition, to leave the
4523 maximum possible space before it, to store other data.
4525 These two values are in units of bytes, but must be aligned to an
4526 MMC sector boundary.
4528 - CONFIG_ENV_OFFSET_REDUND (optional):
4530 Specifies a second storage area, of CONFIG_ENV_SIZE size, used to
4531 hold a redundant copy of the environment data. This provides a
4532 valid backup copy in case the other copy is corrupted, e.g. due
4533 to a power failure during a "saveenv" operation.
4535 This value may also be positive or negative; this is handled in the
4536 same way as CONFIG_ENV_OFFSET.
4538 This value is also in units of bytes, but must also be aligned to
4539 an MMC sector boundary.
4541 - CONFIG_ENV_SIZE_REDUND (optional):
4543 This value need not be set, even when CONFIG_ENV_OFFSET_REDUND is
4544 set. If this value is set, it must be set to the same value as
4547 - CONFIG_SYS_SPI_INIT_OFFSET
4549 Defines offset to the initial SPI buffer area in DPRAM. The
4550 area is used at an early stage (ROM part) if the environment
4551 is configured to reside in the SPI EEPROM: We need a 520 byte
4552 scratch DPRAM area. It is used between the two initialization
4553 calls (spi_init_f() and spi_init_r()). A value of 0xB00 seems
4554 to be a good choice since it makes it far enough from the
4555 start of the data area as well as from the stack pointer.
4557 Please note that the environment is read-only until the monitor
4558 has been relocated to RAM and a RAM copy of the environment has been
4559 created; also, when using EEPROM you will have to use getenv_f()
4560 until then to read environment variables.
4562 The environment is protected by a CRC32 checksum. Before the monitor
4563 is relocated into RAM, as a result of a bad CRC you will be working
4564 with the compiled-in default environment - *silently*!!! [This is
4565 necessary, because the first environment variable we need is the
4566 "baudrate" setting for the console - if we have a bad CRC, we don't
4567 have any device yet where we could complain.]
4569 Note: once the monitor has been relocated, then it will complain if
4570 the default environment is used; a new CRC is computed as soon as you
4571 use the "saveenv" command to store a valid environment.
4573 - CONFIG_SYS_FAULT_ECHO_LINK_DOWN:
4574 Echo the inverted Ethernet link state to the fault LED.
4576 Note: If this option is active, then CONFIG_SYS_FAULT_MII_ADDR
4577 also needs to be defined.
4579 - CONFIG_SYS_FAULT_MII_ADDR:
4580 MII address of the PHY to check for the Ethernet link state.
4582 - CONFIG_NS16550_MIN_FUNCTIONS:
4583 Define this if you desire to only have use of the NS16550_init
4584 and NS16550_putc functions for the serial driver located at
4585 drivers/serial/ns16550.c. This option is useful for saving
4586 space for already greatly restricted images, including but not
4587 limited to NAND_SPL configurations.
4589 - CONFIG_DISPLAY_BOARDINFO
4590 Display information about the board that U-Boot is running on
4591 when U-Boot starts up. The board function checkboard() is called
4594 - CONFIG_DISPLAY_BOARDINFO_LATE
4595 Similar to the previous option, but display this information
4596 later, once stdio is running and output goes to the LCD, if
4599 - CONFIG_BOARD_SIZE_LIMIT:
4600 Maximum size of the U-Boot image. When defined, the
4601 build system checks that the actual size does not
4604 Low Level (hardware related) configuration options:
4605 ---------------------------------------------------
4607 - CONFIG_SYS_CACHELINE_SIZE:
4608 Cache Line Size of the CPU.
4610 - CONFIG_SYS_DEFAULT_IMMR:
4611 Default address of the IMMR after system reset.
4613 Needed on some 8260 systems (MPC8260ADS, PQ2FADS-ZU,
4614 and RPXsuper) to be able to adjust the position of
4615 the IMMR register after a reset.
4617 - CONFIG_SYS_CCSRBAR_DEFAULT:
4618 Default (power-on reset) physical address of CCSR on Freescale
4621 - CONFIG_SYS_CCSRBAR:
4622 Virtual address of CCSR. On a 32-bit build, this is typically
4623 the same value as CONFIG_SYS_CCSRBAR_DEFAULT.
4625 CONFIG_SYS_DEFAULT_IMMR must also be set to this value,
4626 for cross-platform code that uses that macro instead.
4628 - CONFIG_SYS_CCSRBAR_PHYS:
4629 Physical address of CCSR. CCSR can be relocated to a new
4630 physical address, if desired. In this case, this macro should
4631 be set to that address. Otherwise, it should be set to the
4632 same value as CONFIG_SYS_CCSRBAR_DEFAULT. For example, CCSR
4633 is typically relocated on 36-bit builds. It is recommended
4634 that this macro be defined via the _HIGH and _LOW macros:
4636 #define CONFIG_SYS_CCSRBAR_PHYS ((CONFIG_SYS_CCSRBAR_PHYS_HIGH
4637 * 1ull) << 32 | CONFIG_SYS_CCSRBAR_PHYS_LOW)
4639 - CONFIG_SYS_CCSRBAR_PHYS_HIGH:
4640 Bits 33-36 of CONFIG_SYS_CCSRBAR_PHYS. This value is typically
4641 either 0 (32-bit build) or 0xF (36-bit build). This macro is
4642 used in assembly code, so it must not contain typecasts or
4643 integer size suffixes (e.g. "ULL").
4645 - CONFIG_SYS_CCSRBAR_PHYS_LOW:
4646 Lower 32-bits of CONFIG_SYS_CCSRBAR_PHYS. This macro is
4647 used in assembly code, so it must not contain typecasts or
4648 integer size suffixes (e.g. "ULL").
4650 - CONFIG_SYS_CCSR_DO_NOT_RELOCATE:
4651 If this macro is defined, then CONFIG_SYS_CCSRBAR_PHYS will be
4652 forced to a value that ensures that CCSR is not relocated.
4654 - Floppy Disk Support:
4655 CONFIG_SYS_FDC_DRIVE_NUMBER
4657 the default drive number (default value 0)
4659 CONFIG_SYS_ISA_IO_STRIDE
4661 defines the spacing between FDC chipset registers
4664 CONFIG_SYS_ISA_IO_OFFSET
4666 defines the offset of register from address. It
4667 depends on which part of the data bus is connected to
4668 the FDC chipset. (default value 0)
4670 If CONFIG_SYS_ISA_IO_STRIDE CONFIG_SYS_ISA_IO_OFFSET and
4671 CONFIG_SYS_FDC_DRIVE_NUMBER are undefined, they take their
4674 if CONFIG_SYS_FDC_HW_INIT is defined, then the function
4675 fdc_hw_init() is called at the beginning of the FDC
4676 setup. fdc_hw_init() must be provided by the board
4677 source code. It is used to make hardware-dependent
4681 Most IDE controllers were designed to be connected with PCI
4682 interface. Only few of them were designed for AHB interface.
4683 When software is doing ATA command and data transfer to
4684 IDE devices through IDE-AHB controller, some additional
4685 registers accessing to these kind of IDE-AHB controller
4688 - CONFIG_SYS_IMMR: Physical address of the Internal Memory.
4689 DO NOT CHANGE unless you know exactly what you're
4690 doing! (11-4) [MPC8xx/82xx systems only]
4692 - CONFIG_SYS_INIT_RAM_ADDR:
4694 Start address of memory area that can be used for
4695 initial data and stack; please note that this must be
4696 writable memory that is working WITHOUT special
4697 initialization, i. e. you CANNOT use normal RAM which
4698 will become available only after programming the
4699 memory controller and running certain initialization
4702 U-Boot uses the following memory types:
4703 - MPC8xx and MPC8260: IMMR (internal memory of the CPU)
4704 - MPC824X: data cache
4705 - PPC4xx: data cache
4707 - CONFIG_SYS_GBL_DATA_OFFSET:
4709 Offset of the initial data structure in the memory
4710 area defined by CONFIG_SYS_INIT_RAM_ADDR. Usually
4711 CONFIG_SYS_GBL_DATA_OFFSET is chosen such that the initial
4712 data is located at the end of the available space
4713 (sometimes written as (CONFIG_SYS_INIT_RAM_SIZE -
4714 CONFIG_SYS_INIT_DATA_SIZE), and the initial stack is just
4715 below that area (growing from (CONFIG_SYS_INIT_RAM_ADDR +
4716 CONFIG_SYS_GBL_DATA_OFFSET) downward.
4719 On the MPC824X (or other systems that use the data
4720 cache for initial memory) the address chosen for
4721 CONFIG_SYS_INIT_RAM_ADDR is basically arbitrary - it must
4722 point to an otherwise UNUSED address space between
4723 the top of RAM and the start of the PCI space.
4725 - CONFIG_SYS_SIUMCR: SIU Module Configuration (11-6)
4727 - CONFIG_SYS_SYPCR: System Protection Control (11-9)
4729 - CONFIG_SYS_TBSCR: Time Base Status and Control (11-26)
4731 - CONFIG_SYS_PISCR: Periodic Interrupt Status and Control (11-31)
4733 - CONFIG_SYS_PLPRCR: PLL, Low-Power, and Reset Control Register (15-30)
4735 - CONFIG_SYS_SCCR: System Clock and reset Control Register (15-27)
4737 - CONFIG_SYS_OR_TIMING_SDRAM:
4740 - CONFIG_SYS_MAMR_PTA:
4741 periodic timer for refresh
4743 - CONFIG_SYS_DER: Debug Event Register (37-47)
4745 - FLASH_BASE0_PRELIM, FLASH_BASE1_PRELIM, CONFIG_SYS_REMAP_OR_AM,
4746 CONFIG_SYS_PRELIM_OR_AM, CONFIG_SYS_OR_TIMING_FLASH, CONFIG_SYS_OR0_REMAP,
4747 CONFIG_SYS_OR0_PRELIM, CONFIG_SYS_BR0_PRELIM, CONFIG_SYS_OR1_REMAP, CONFIG_SYS_OR1_PRELIM,
4748 CONFIG_SYS_BR1_PRELIM:
4749 Memory Controller Definitions: BR0/1 and OR0/1 (FLASH)
4751 - SDRAM_BASE2_PRELIM, SDRAM_BASE3_PRELIM, SDRAM_MAX_SIZE,
4752 CONFIG_SYS_OR_TIMING_SDRAM, CONFIG_SYS_OR2_PRELIM, CONFIG_SYS_BR2_PRELIM,
4753 CONFIG_SYS_OR3_PRELIM, CONFIG_SYS_BR3_PRELIM:
4754 Memory Controller Definitions: BR2/3 and OR2/3 (SDRAM)
4756 - CONFIG_SYS_MAMR_PTA, CONFIG_SYS_MPTPR_2BK_4K, CONFIG_SYS_MPTPR_1BK_4K, CONFIG_SYS_MPTPR_2BK_8K,
4757 CONFIG_SYS_MPTPR_1BK_8K, CONFIG_SYS_MAMR_8COL, CONFIG_SYS_MAMR_9COL:
4758 Machine Mode Register and Memory Periodic Timer
4759 Prescaler definitions (SDRAM timing)
4761 - CONFIG_SYS_I2C_UCODE_PATCH, CONFIG_SYS_I2C_DPMEM_OFFSET [0x1FC0]:
4762 enable I2C microcode relocation patch (MPC8xx);
4763 define relocation offset in DPRAM [DSP2]
4765 - CONFIG_SYS_SMC_UCODE_PATCH, CONFIG_SYS_SMC_DPMEM_OFFSET [0x1FC0]:
4766 enable SMC microcode relocation patch (MPC8xx);
4767 define relocation offset in DPRAM [SMC1]
4769 - CONFIG_SYS_SPI_UCODE_PATCH, CONFIG_SYS_SPI_DPMEM_OFFSET [0x1FC0]:
4770 enable SPI microcode relocation patch (MPC8xx);
4771 define relocation offset in DPRAM [SCC4]
4773 - CONFIG_SYS_USE_OSCCLK:
4774 Use OSCM clock mode on MBX8xx board. Be careful,
4775 wrong setting might damage your board. Read
4776 doc/README.MBX before setting this variable!
4778 - CONFIG_SYS_CPM_POST_WORD_ADDR: (MPC8xx, MPC8260 only)
4779 Offset of the bootmode word in DPRAM used by post
4780 (Power On Self Tests). This definition overrides
4781 #define'd default value in commproc.h resp.
4784 - CONFIG_SYS_PCI_SLV_MEM_LOCAL, CONFIG_SYS_PCI_SLV_MEM_BUS, CONFIG_SYS_PICMR0_MASK_ATTRIB,
4785 CONFIG_SYS_PCI_MSTR0_LOCAL, CONFIG_SYS_PCIMSK0_MASK, CONFIG_SYS_PCI_MSTR1_LOCAL,
4786 CONFIG_SYS_PCIMSK1_MASK, CONFIG_SYS_PCI_MSTR_MEM_LOCAL, CONFIG_SYS_PCI_MSTR_MEM_BUS,
4787 CONFIG_SYS_CPU_PCI_MEM_START, CONFIG_SYS_PCI_MSTR_MEM_SIZE, CONFIG_SYS_POCMR0_MASK_ATTRIB,
4788 CONFIG_SYS_PCI_MSTR_MEMIO_LOCAL, CONFIG_SYS_PCI_MSTR_MEMIO_BUS, CPU_PCI_MEMIO_START,
4789 CONFIG_SYS_PCI_MSTR_MEMIO_SIZE, CONFIG_SYS_POCMR1_MASK_ATTRIB, CONFIG_SYS_PCI_MSTR_IO_LOCAL,
4790 CONFIG_SYS_PCI_MSTR_IO_BUS, CONFIG_SYS_CPU_PCI_IO_START, CONFIG_SYS_PCI_MSTR_IO_SIZE,
4791 CONFIG_SYS_POCMR2_MASK_ATTRIB: (MPC826x only)
4792 Overrides the default PCI memory map in arch/powerpc/cpu/mpc8260/pci.c if set.
4794 - CONFIG_PCI_DISABLE_PCIE:
4795 Disable PCI-Express on systems where it is supported but not
4798 - CONFIG_PCI_ENUM_ONLY
4799 Only scan through and get the devices on the buses.
4800 Don't do any setup work, presumably because someone or
4801 something has already done it, and we don't need to do it
4802 a second time. Useful for platforms that are pre-booted
4803 by coreboot or similar.
4805 - CONFIG_PCI_INDIRECT_BRIDGE:
4806 Enable support for indirect PCI bridges.
4809 Chip has SRIO or not
4812 Board has SRIO 1 port available
4815 Board has SRIO 2 port available
4817 - CONFIG_SRIO_PCIE_BOOT_MASTER
4818 Board can support master function for Boot from SRIO and PCIE
4820 - CONFIG_SYS_SRIOn_MEM_VIRT:
4821 Virtual Address of SRIO port 'n' memory region
4823 - CONFIG_SYS_SRIOn_MEM_PHYS:
4824 Physical Address of SRIO port 'n' memory region
4826 - CONFIG_SYS_SRIOn_MEM_SIZE:
4827 Size of SRIO port 'n' memory region
4829 - CONFIG_SYS_NAND_BUSWIDTH_16BIT
4830 Defined to tell the NAND controller that the NAND chip is using
4832 Not all NAND drivers use this symbol.
4833 Example of drivers that use it:
4834 - drivers/mtd/nand/ndfc.c
4835 - drivers/mtd/nand/mxc_nand.c
4837 - CONFIG_SYS_NDFC_EBC0_CFG
4838 Sets the EBC0_CFG register for the NDFC. If not defined
4839 a default value will be used.
4842 Get DDR timing information from an I2C EEPROM. Common
4843 with pluggable memory modules such as SODIMMs
4846 I2C address of the SPD EEPROM
4848 - CONFIG_SYS_SPD_BUS_NUM
4849 If SPD EEPROM is on an I2C bus other than the first
4850 one, specify here. Note that the value must resolve
4851 to something your driver can deal with.
4853 - CONFIG_SYS_DDR_RAW_TIMING
4854 Get DDR timing information from other than SPD. Common with
4855 soldered DDR chips onboard without SPD. DDR raw timing
4856 parameters are extracted from datasheet and hard-coded into
4857 header files or board specific files.
4859 - CONFIG_FSL_DDR_INTERACTIVE
4860 Enable interactive DDR debugging. See doc/README.fsl-ddr.
4862 - CONFIG_FSL_DDR_SYNC_REFRESH
4863 Enable sync of refresh for multiple controllers.
4865 - CONFIG_SYS_83XX_DDR_USES_CS0
4866 Only for 83xx systems. If specified, then DDR should
4867 be configured using CS0 and CS1 instead of CS2 and CS3.
4869 - CONFIG_ETHER_ON_FEC[12]
4870 Define to enable FEC[12] on a 8xx series processor.
4872 - CONFIG_FEC[12]_PHY
4873 Define to the hardcoded PHY address which corresponds
4874 to the given FEC; i. e.
4875 #define CONFIG_FEC1_PHY 4
4876 means that the PHY with address 4 is connected to FEC1
4878 When set to -1, means to probe for first available.
4880 - CONFIG_FEC[12]_PHY_NORXERR
4881 The PHY does not have a RXERR line (RMII only).
4882 (so program the FEC to ignore it).
4885 Enable RMII mode for all FECs.
4886 Note that this is a global option, we can't
4887 have one FEC in standard MII mode and another in RMII mode.
4889 - CONFIG_CRC32_VERIFY
4890 Add a verify option to the crc32 command.
4893 => crc32 -v <address> <count> <crc32>
4895 Where address/count indicate a memory area
4896 and crc32 is the correct crc32 which the
4900 Add the "loopw" memory command. This only takes effect if
4901 the memory commands are activated globally (CONFIG_CMD_MEM).
4904 Add the "mdc" and "mwc" memory commands. These are cyclic
4909 This command will print 4 bytes (10,11,12,13) each 500 ms.
4911 => mwc.l 100 12345678 10
4912 This command will write 12345678 to address 100 all 10 ms.
4914 This only takes effect if the memory commands are activated
4915 globally (CONFIG_CMD_MEM).
4917 - CONFIG_SKIP_LOWLEVEL_INIT
4918 [ARM, NDS32, MIPS only] If this variable is defined, then certain
4919 low level initializations (like setting up the memory
4920 controller) are omitted and/or U-Boot does not
4921 relocate itself into RAM.
4923 Normally this variable MUST NOT be defined. The only
4924 exception is when U-Boot is loaded (to RAM) by some
4925 other boot loader or by a debugger which performs
4926 these initializations itself.
4929 Modifies the behaviour of start.S when compiling a loader
4930 that is executed before the actual U-Boot. E.g. when
4931 compiling a NAND SPL.
4934 Modifies the behaviour of start.S when compiling a loader
4935 that is executed after the SPL and before the actual U-Boot.
4936 It is loaded by the SPL.
4938 - CONFIG_SYS_MPC85XX_NO_RESETVEC
4939 Only for 85xx systems. If this variable is specified, the section
4940 .resetvec is not kept and the section .bootpg is placed in the
4941 previous 4k of the .text section.
4943 - CONFIG_ARCH_MAP_SYSMEM
4944 Generally U-Boot (and in particular the md command) uses
4945 effective address. It is therefore not necessary to regard
4946 U-Boot address as virtual addresses that need to be translated
4947 to physical addresses. However, sandbox requires this, since
4948 it maintains its own little RAM buffer which contains all
4949 addressable memory. This option causes some memory accesses
4950 to be mapped through map_sysmem() / unmap_sysmem().
4952 - CONFIG_USE_ARCH_MEMCPY
4953 CONFIG_USE_ARCH_MEMSET
4954 If these options are used a optimized version of memcpy/memset will
4955 be used if available. These functions may be faster under some
4956 conditions but may increase the binary size.
4958 - CONFIG_X86_RESET_VECTOR
4959 If defined, the x86 reset vector code is included. This is not
4960 needed when U-Boot is running from Coreboot.
4963 Defines the MPU clock speed (in MHz).
4965 NOTE : currently only supported on AM335x platforms.
4967 - CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC:
4968 Enables the RTC32K OSC on AM33xx based plattforms
4970 - CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
4971 Option to disable subpage write in NAND driver
4972 driver that uses this:
4973 drivers/mtd/nand/davinci_nand.c
4975 Freescale QE/FMAN Firmware Support:
4976 -----------------------------------
4978 The Freescale QUICCEngine (QE) and Frame Manager (FMAN) both support the
4979 loading of "firmware", which is encoded in the QE firmware binary format.
4980 This firmware often needs to be loaded during U-Boot booting, so macros
4981 are used to identify the storage device (NOR flash, SPI, etc) and the address
4984 - CONFIG_SYS_FMAN_FW_ADDR
4985 The address in the storage device where the FMAN microcode is located. The
4986 meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
4989 - CONFIG_SYS_QE_FW_ADDR
4990 The address in the storage device where the QE microcode is located. The
4991 meaning of this address depends on which CONFIG_SYS_QE_FW_IN_xxx macro
4994 - CONFIG_SYS_QE_FMAN_FW_LENGTH
4995 The maximum possible size of the firmware. The firmware binary format
4996 has a field that specifies the actual size of the firmware, but it
4997 might not be possible to read any part of the firmware unless some
4998 local storage is allocated to hold the entire firmware first.
5000 - CONFIG_SYS_QE_FMAN_FW_IN_NOR
5001 Specifies that QE/FMAN firmware is located in NOR flash, mapped as
5002 normal addressable memory via the LBC. CONFIG_SYS_FMAN_FW_ADDR is the
5003 virtual address in NOR flash.
5005 - CONFIG_SYS_QE_FMAN_FW_IN_NAND
5006 Specifies that QE/FMAN firmware is located in NAND flash.
5007 CONFIG_SYS_FMAN_FW_ADDR is the offset within NAND flash.
5009 - CONFIG_SYS_QE_FMAN_FW_IN_MMC
5010 Specifies that QE/FMAN firmware is located on the primary SD/MMC
5011 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
5013 - CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH
5014 Specifies that QE/FMAN firmware is located on the primary SPI
5015 device. CONFIG_SYS_FMAN_FW_ADDR is the byte offset on that device.
5017 - CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
5018 Specifies that QE/FMAN firmware is located in the remote (master)
5019 memory space. CONFIG_SYS_FMAN_FW_ADDR is a virtual address which
5020 can be mapped from slave TLB->slave LAW->slave SRIO or PCIE outbound
5021 window->master inbound window->master LAW->the ucode address in
5022 master's memory space.
5024 Freescale Layerscape Management Complex Firmware Support:
5025 ---------------------------------------------------------
5026 The Freescale Layerscape Management Complex (MC) supports the loading of
5028 This firmware often needs to be loaded during U-Boot booting, so macros
5029 are used to identify the storage device (NOR flash, SPI, etc) and the address
5032 - CONFIG_FSL_MC_ENET
5033 Enable the MC driver for Layerscape SoCs.
5035 - CONFIG_SYS_LS_MC_FW_ADDR
5036 The address in the storage device where the firmware is located. The
5037 meaning of this address depends on which CONFIG_SYS_LS_MC_FW_IN_xxx macro
5040 - CONFIG_SYS_LS_MC_FW_LENGTH
5041 The maximum possible size of the firmware. The firmware binary format
5042 has a field that specifies the actual size of the firmware, but it
5043 might not be possible to read any part of the firmware unless some
5044 local storage is allocated to hold the entire firmware first.
5046 - CONFIG_SYS_LS_MC_FW_IN_NOR
5047 Specifies that MC firmware is located in NOR flash, mapped as
5048 normal addressable memory via the LBC. CONFIG_SYS_LS_MC_FW_ADDR is the
5049 virtual address in NOR flash.
5051 Building the Software:
5052 ======================
5054 Building U-Boot has been tested in several native build environments
5055 and in many different cross environments. Of course we cannot support
5056 all possibly existing versions of cross development tools in all
5057 (potentially obsolete) versions. In case of tool chain problems we
5058 recommend to use the ELDK (see http://www.denx.de/wiki/DULG/ELDK)
5059 which is extensively used to build and test U-Boot.
5061 If you are not using a native environment, it is assumed that you
5062 have GNU cross compiling tools available in your path. In this case,
5063 you must set the environment variable CROSS_COMPILE in your shell.
5064 Note that no changes to the Makefile or any other source files are
5065 necessary. For example using the ELDK on a 4xx CPU, please enter:
5067 $ CROSS_COMPILE=ppc_4xx-
5068 $ export CROSS_COMPILE
5070 Note: If you wish to generate Windows versions of the utilities in
5071 the tools directory you can use the MinGW toolchain
5072 (http://www.mingw.org). Set your HOST tools to the MinGW
5073 toolchain and execute 'make tools'. For example:
5075 $ make HOSTCC=i586-mingw32msvc-gcc HOSTSTRIP=i586-mingw32msvc-strip tools
5077 Binaries such as tools/mkimage.exe will be created which can
5078 be executed on computers running Windows.
5080 U-Boot is intended to be simple to build. After installing the
5081 sources you must configure U-Boot for one specific board type. This
5086 where "NAME_defconfig" is the name of one of the existing configu-
5087 rations; see boards.cfg for supported names.
5089 Note: for some board special configuration names may exist; check if
5090 additional information is available from the board vendor; for
5091 instance, the TQM823L systems are available without (standard)
5092 or with LCD support. You can select such additional "features"
5093 when choosing the configuration, i. e.
5095 make TQM823L_defconfig
5096 - will configure for a plain TQM823L, i. e. no LCD support
5098 make TQM823L_LCD_defconfig
5099 - will configure for a TQM823L with U-Boot console on LCD
5104 Finally, type "make all", and you should get some working U-Boot
5105 images ready for download to / installation on your system:
5107 - "u-boot.bin" is a raw binary image
5108 - "u-boot" is an image in ELF binary format
5109 - "u-boot.srec" is in Motorola S-Record format
5111 By default the build is performed locally and the objects are saved
5112 in the source directory. One of the two methods can be used to change
5113 this behavior and build U-Boot to some external directory:
5115 1. Add O= to the make command line invocations:
5117 make O=/tmp/build distclean
5118 make O=/tmp/build NAME_defconfig
5119 make O=/tmp/build all
5121 2. Set environment variable KBUILD_OUTPUT to point to the desired location:
5123 export KBUILD_OUTPUT=/tmp/build
5128 Note that the command line "O=" setting overrides the KBUILD_OUTPUT environment
5132 Please be aware that the Makefiles assume you are using GNU make, so
5133 for instance on NetBSD you might need to use "gmake" instead of
5137 If the system board that you have is not listed, then you will need
5138 to port U-Boot to your hardware platform. To do this, follow these
5141 1. Add a new configuration option for your board to the toplevel
5142 "boards.cfg" file, using the existing entries as examples.
5143 Follow the instructions there to keep the boards in order.
5144 2. Create a new directory to hold your board specific code. Add any
5145 files you need. In your board directory, you will need at least
5146 the "Makefile", a "<board>.c", "flash.c" and "u-boot.lds".
5147 3. Create a new configuration file "include/configs/<board>.h" for
5149 3. If you're porting U-Boot to a new CPU, then also create a new
5150 directory to hold your CPU specific code. Add any files you need.
5151 4. Run "make <board>_defconfig" with your new name.
5152 5. Type "make", and you should get a working "u-boot.srec" file
5153 to be installed on your target system.
5154 6. Debug and solve any problems that might arise.
5155 [Of course, this last step is much harder than it sounds.]
5158 Testing of U-Boot Modifications, Ports to New Hardware, etc.:
5159 ==============================================================
5161 If you have modified U-Boot sources (for instance added a new board
5162 or support for new devices, a new CPU, etc.) you are expected to
5163 provide feedback to the other developers. The feedback normally takes
5164 the form of a "patch", i. e. a context diff against a certain (latest
5165 official or latest in the git repository) version of U-Boot sources.
5167 But before you submit such a patch, please verify that your modifi-
5168 cation did not break existing code. At least make sure that *ALL* of
5169 the supported boards compile WITHOUT ANY compiler warnings. To do so,
5170 just run the "MAKEALL" script, which will configure and build U-Boot
5171 for ALL supported system. Be warned, this will take a while. You can
5172 select which (cross) compiler to use by passing a `CROSS_COMPILE'
5173 environment variable to the script, i. e. to use the ELDK cross tools
5176 CROSS_COMPILE=ppc_8xx- MAKEALL
5178 or to build on a native PowerPC system you can type
5180 CROSS_COMPILE=' ' MAKEALL
5182 When using the MAKEALL script, the default behaviour is to build
5183 U-Boot in the source directory. This location can be changed by
5184 setting the BUILD_DIR environment variable. Also, for each target
5185 built, the MAKEALL script saves two log files (<target>.ERR and
5186 <target>.MAKEALL) in the <source dir>/LOG directory. This default
5187 location can be changed by setting the MAKEALL_LOGDIR environment
5188 variable. For example:
5190 export BUILD_DIR=/tmp/build
5191 export MAKEALL_LOGDIR=/tmp/log
5192 CROSS_COMPILE=ppc_8xx- MAKEALL
5194 With the above settings build objects are saved in the /tmp/build,
5195 log files are saved in the /tmp/log and the source tree remains clean
5196 during the whole build process.
5199 See also "U-Boot Porting Guide" below.
5202 Monitor Commands - Overview:
5203 ============================
5205 go - start application at address 'addr'
5206 run - run commands in an environment variable
5207 bootm - boot application image from memory
5208 bootp - boot image via network using BootP/TFTP protocol
5209 bootz - boot zImage from memory
5210 tftpboot- boot image via network using TFTP protocol
5211 and env variables "ipaddr" and "serverip"
5212 (and eventually "gatewayip")
5213 tftpput - upload a file via network using TFTP protocol
5214 rarpboot- boot image via network using RARP/TFTP protocol
5215 diskboot- boot from IDE devicebootd - boot default, i.e., run 'bootcmd'
5216 loads - load S-Record file over serial line
5217 loadb - load binary file over serial line (kermit mode)
5219 mm - memory modify (auto-incrementing)
5220 nm - memory modify (constant address)
5221 mw - memory write (fill)
5223 cmp - memory compare
5224 crc32 - checksum calculation
5225 i2c - I2C sub-system
5226 sspi - SPI utility commands
5227 base - print or set address offset
5228 printenv- print environment variables
5229 setenv - set environment variables
5230 saveenv - save environment variables to persistent storage
5231 protect - enable or disable FLASH write protection
5232 erase - erase FLASH memory
5233 flinfo - print FLASH memory information
5234 nand - NAND memory operations (see doc/README.nand)
5235 bdinfo - print Board Info structure
5236 iminfo - print header information for application image
5237 coninfo - print console devices and informations
5238 ide - IDE sub-system
5239 loop - infinite loop on address range
5240 loopw - infinite write loop on address range
5241 mtest - simple RAM test
5242 icache - enable or disable instruction cache
5243 dcache - enable or disable data cache
5244 reset - Perform RESET of the CPU
5245 echo - echo args to console
5246 version - print monitor version
5247 help - print online help
5248 ? - alias for 'help'
5251 Monitor Commands - Detailed Description:
5252 ========================================
5256 For now: just type "help <command>".
5259 Environment Variables:
5260 ======================
5262 U-Boot supports user configuration using Environment Variables which
5263 can be made persistent by saving to Flash memory.
5265 Environment Variables are set using "setenv", printed using
5266 "printenv", and saved to Flash using "saveenv". Using "setenv"
5267 without a value can be used to delete a variable from the
5268 environment. As long as you don't save the environment you are
5269 working with an in-memory copy. In case the Flash area containing the
5270 environment is erased by accident, a default environment is provided.
5272 Some configuration options can be set using Environment Variables.
5274 List of environment variables (most likely not complete):
5276 baudrate - see CONFIG_BAUDRATE
5278 bootdelay - see CONFIG_BOOTDELAY
5280 bootcmd - see CONFIG_BOOTCOMMAND
5282 bootargs - Boot arguments when booting an RTOS image
5284 bootfile - Name of the image to load with TFTP
5286 bootm_low - Memory range available for image processing in the bootm
5287 command can be restricted. This variable is given as
5288 a hexadecimal number and defines lowest address allowed
5289 for use by the bootm command. See also "bootm_size"
5290 environment variable. Address defined by "bootm_low" is
5291 also the base of the initial memory mapping for the Linux
5292 kernel -- see the description of CONFIG_SYS_BOOTMAPSZ and
5295 bootm_mapsize - Size of the initial memory mapping for the Linux kernel.
5296 This variable is given as a hexadecimal number and it
5297 defines the size of the memory region starting at base
5298 address bootm_low that is accessible by the Linux kernel
5299 during early boot. If unset, CONFIG_SYS_BOOTMAPSZ is used
5300 as the default value if it is defined, and bootm_size is
5303 bootm_size - Memory range available for image processing in the bootm
5304 command can be restricted. This variable is given as
5305 a hexadecimal number and defines the size of the region
5306 allowed for use by the bootm command. See also "bootm_low"
5307 environment variable.
5309 updatefile - Location of the software update file on a TFTP server, used
5310 by the automatic software update feature. Please refer to
5311 documentation in doc/README.update for more details.
5313 autoload - if set to "no" (any string beginning with 'n'),
5314 "bootp" will just load perform a lookup of the
5315 configuration from the BOOTP server, but not try to
5316 load any image using TFTP
5318 autostart - if set to "yes", an image loaded using the "bootp",
5319 "rarpboot", "tftpboot" or "diskboot" commands will
5320 be automatically started (by internally calling
5323 If set to "no", a standalone image passed to the
5324 "bootm" command will be copied to the load address
5325 (and eventually uncompressed), but NOT be started.
5326 This can be used to load and uncompress arbitrary
5329 fdt_high - if set this restricts the maximum address that the
5330 flattened device tree will be copied into upon boot.
5331 For example, if you have a system with 1 GB memory
5332 at physical address 0x10000000, while Linux kernel
5333 only recognizes the first 704 MB as low memory, you
5334 may need to set fdt_high as 0x3C000000 to have the
5335 device tree blob be copied to the maximum address
5336 of the 704 MB low memory, so that Linux kernel can
5337 access it during the boot procedure.
5339 If this is set to the special value 0xFFFFFFFF then
5340 the fdt will not be copied at all on boot. For this
5341 to work it must reside in writable memory, have
5342 sufficient padding on the end of it for u-boot to
5343 add the information it needs into it, and the memory
5344 must be accessible by the kernel.
5346 fdtcontroladdr- if set this is the address of the control flattened
5347 device tree used by U-Boot when CONFIG_OF_CONTROL is
5350 i2cfast - (PPC405GP|PPC405EP only)
5351 if set to 'y' configures Linux I2C driver for fast
5352 mode (400kHZ). This environment variable is used in
5353 initialization code. So, for changes to be effective
5354 it must be saved and board must be reset.
5356 initrd_high - restrict positioning of initrd images:
5357 If this variable is not set, initrd images will be
5358 copied to the highest possible address in RAM; this
5359 is usually what you want since it allows for
5360 maximum initrd size. If for some reason you want to
5361 make sure that the initrd image is loaded below the
5362 CONFIG_SYS_BOOTMAPSZ limit, you can set this environment
5363 variable to a value of "no" or "off" or "0".
5364 Alternatively, you can set it to a maximum upper
5365 address to use (U-Boot will still check that it
5366 does not overwrite the U-Boot stack and data).
5368 For instance, when you have a system with 16 MB
5369 RAM, and want to reserve 4 MB from use by Linux,
5370 you can do this by adding "mem=12M" to the value of
5371 the "bootargs" variable. However, now you must make
5372 sure that the initrd image is placed in the first
5373 12 MB as well - this can be done with
5375 setenv initrd_high 00c00000
5377 If you set initrd_high to 0xFFFFFFFF, this is an
5378 indication to U-Boot that all addresses are legal
5379 for the Linux kernel, including addresses in flash
5380 memory. In this case U-Boot will NOT COPY the
5381 ramdisk at all. This may be useful to reduce the
5382 boot time on your system, but requires that this
5383 feature is supported by your Linux kernel.
5385 ipaddr - IP address; needed for tftpboot command
5387 loadaddr - Default load address for commands like "bootp",
5388 "rarpboot", "tftpboot", "loadb" or "diskboot"
5390 loads_echo - see CONFIG_LOADS_ECHO
5392 serverip - TFTP server IP address; needed for tftpboot command
5394 bootretry - see CONFIG_BOOT_RETRY_TIME
5396 bootdelaykey - see CONFIG_AUTOBOOT_DELAY_STR
5398 bootstopkey - see CONFIG_AUTOBOOT_STOP_STR
5400 ethprime - controls which interface is used first.
5402 ethact - controls which interface is currently active.
5403 For example you can do the following
5405 => setenv ethact FEC
5406 => ping 192.168.0.1 # traffic sent on FEC
5407 => setenv ethact SCC
5408 => ping 10.0.0.1 # traffic sent on SCC
5410 ethrotate - When set to "no" U-Boot does not go through all
5411 available network interfaces.
5412 It just stays at the currently selected interface.
5414 netretry - When set to "no" each network operation will
5415 either succeed or fail without retrying.
5416 When set to "once" the network operation will
5417 fail when all the available network interfaces
5418 are tried once without success.
5419 Useful on scripts which control the retry operation
5422 npe_ucode - set load address for the NPE microcode
5424 silent_linux - If set then Linux will be told to boot silently, by
5425 changing the console to be empty. If "yes" it will be
5426 made silent. If "no" it will not be made silent. If
5427 unset, then it will be made silent if the U-Boot console
5430 tftpsrcport - If this is set, the value is used for TFTP's
5433 tftpdstport - If this is set, the value is used for TFTP's UDP
5434 destination port instead of the Well Know Port 69.
5436 tftpblocksize - Block size to use for TFTP transfers; if not set,
5437 we use the TFTP server's default block size
5439 tftptimeout - Retransmission timeout for TFTP packets (in milli-
5440 seconds, minimum value is 1000 = 1 second). Defines
5441 when a packet is considered to be lost so it has to
5442 be retransmitted. The default is 5000 = 5 seconds.
5443 Lowering this value may make downloads succeed
5444 faster in networks with high packet loss rates or
5445 with unreliable TFTP servers.
5447 vlan - When set to a value < 4095 the traffic over
5448 Ethernet is encapsulated/received over 802.1q
5451 The following image location variables contain the location of images
5452 used in booting. The "Image" column gives the role of the image and is
5453 not an environment variable name. The other columns are environment
5454 variable names. "File Name" gives the name of the file on a TFTP
5455 server, "RAM Address" gives the location in RAM the image will be
5456 loaded to, and "Flash Location" gives the image's address in NOR
5457 flash or offset in NAND flash.
5459 *Note* - these variables don't have to be defined for all boards, some
5460 boards currenlty use other variables for these purposes, and some
5461 boards use these variables for other purposes.
5463 Image File Name RAM Address Flash Location
5464 ----- --------- ----------- --------------
5465 u-boot u-boot u-boot_addr_r u-boot_addr
5466 Linux kernel bootfile kernel_addr_r kernel_addr
5467 device tree blob fdtfile fdt_addr_r fdt_addr
5468 ramdisk ramdiskfile ramdisk_addr_r ramdisk_addr
5470 The following environment variables may be used and automatically
5471 updated by the network boot commands ("bootp" and "rarpboot"),
5472 depending the information provided by your boot server:
5474 bootfile - see above
5475 dnsip - IP address of your Domain Name Server
5476 dnsip2 - IP address of your secondary Domain Name Server
5477 gatewayip - IP address of the Gateway (Router) to use
5478 hostname - Target hostname
5480 netmask - Subnet Mask
5481 rootpath - Pathname of the root filesystem on the NFS server
5482 serverip - see above
5485 There are two special Environment Variables:
5487 serial# - contains hardware identification information such
5488 as type string and/or serial number
5489 ethaddr - Ethernet address
5491 These variables can be set only once (usually during manufacturing of
5492 the board). U-Boot refuses to delete or overwrite these variables
5493 once they have been set once.
5496 Further special Environment Variables:
5498 ver - Contains the U-Boot version string as printed
5499 with the "version" command. This variable is
5500 readonly (see CONFIG_VERSION_VARIABLE).
5503 Please note that changes to some configuration parameters may take
5504 only effect after the next boot (yes, that's just like Windoze :-).
5507 Callback functions for environment variables:
5508 ---------------------------------------------
5510 For some environment variables, the behavior of u-boot needs to change
5511 when their values are changed. This functionality allows functions to
5512 be associated with arbitrary variables. On creation, overwrite, or
5513 deletion, the callback will provide the opportunity for some side
5514 effect to happen or for the change to be rejected.
5516 The callbacks are named and associated with a function using the
5517 U_BOOT_ENV_CALLBACK macro in your board or driver code.
5519 These callbacks are associated with variables in one of two ways. The
5520 static list can be added to by defining CONFIG_ENV_CALLBACK_LIST_STATIC
5521 in the board configuration to a string that defines a list of
5522 associations. The list must be in the following format:
5524 entry = variable_name[:callback_name]
5527 If the callback name is not specified, then the callback is deleted.
5528 Spaces are also allowed anywhere in the list.
5530 Callbacks can also be associated by defining the ".callbacks" variable
5531 with the same list format above. Any association in ".callbacks" will
5532 override any association in the static list. You can define
5533 CONFIG_ENV_CALLBACK_LIST_DEFAULT to a list (string) to define the
5534 ".callbacks" environment variable in the default or embedded environment.
5537 Command Line Parsing:
5538 =====================
5540 There are two different command line parsers available with U-Boot:
5541 the old "simple" one, and the much more powerful "hush" shell:
5543 Old, simple command line parser:
5544 --------------------------------
5546 - supports environment variables (through setenv / saveenv commands)
5547 - several commands on one line, separated by ';'
5548 - variable substitution using "... ${name} ..." syntax
5549 - special characters ('$', ';') can be escaped by prefixing with '\',
5551 setenv bootcmd bootm \${address}
5552 - You can also escape text by enclosing in single apostrophes, for example:
5553 setenv addip 'setenv bootargs $bootargs ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off'
5558 - similar to Bourne shell, with control structures like
5559 if...then...else...fi, for...do...done; while...do...done,
5560 until...do...done, ...
5561 - supports environment ("global") variables (through setenv / saveenv
5562 commands) and local shell variables (through standard shell syntax
5563 "name=value"); only environment variables can be used with "run"
5569 (1) If a command line (or an environment variable executed by a "run"
5570 command) contains several commands separated by semicolon, and
5571 one of these commands fails, then the remaining commands will be
5574 (2) If you execute several variables with one call to run (i. e.
5575 calling run with a list of variables as arguments), any failing
5576 command will cause "run" to terminate, i. e. the remaining
5577 variables are not executed.
5579 Note for Redundant Ethernet Interfaces:
5580 =======================================
5582 Some boards come with redundant Ethernet interfaces; U-Boot supports
5583 such configurations and is capable of automatic selection of a
5584 "working" interface when needed. MAC assignment works as follows:
5586 Network interfaces are numbered eth0, eth1, eth2, ... Corresponding
5587 MAC addresses can be stored in the environment as "ethaddr" (=>eth0),
5588 "eth1addr" (=>eth1), "eth2addr", ...
5590 If the network interface stores some valid MAC address (for instance
5591 in SROM), this is used as default address if there is NO correspon-
5592 ding setting in the environment; if the corresponding environment
5593 variable is set, this overrides the settings in the card; that means:
5595 o If the SROM has a valid MAC address, and there is no address in the
5596 environment, the SROM's address is used.
5598 o If there is no valid address in the SROM, and a definition in the
5599 environment exists, then the value from the environment variable is
5602 o If both the SROM and the environment contain a MAC address, and
5603 both addresses are the same, this MAC address is used.
5605 o If both the SROM and the environment contain a MAC address, and the
5606 addresses differ, the value from the environment is used and a
5609 o If neither SROM nor the environment contain a MAC address, an error
5612 If Ethernet drivers implement the 'write_hwaddr' function, valid MAC addresses
5613 will be programmed into hardware as part of the initialization process. This
5614 may be skipped by setting the appropriate 'ethmacskip' environment variable.
5615 The naming convention is as follows:
5616 "ethmacskip" (=>eth0), "eth1macskip" (=>eth1) etc.
5621 U-Boot is capable of booting (and performing other auxiliary operations on)
5622 images in two formats:
5624 New uImage format (FIT)
5625 -----------------------
5627 Flexible and powerful format based on Flattened Image Tree -- FIT (similar
5628 to Flattened Device Tree). It allows the use of images with multiple
5629 components (several kernels, ramdisks, etc.), with contents protected by
5630 SHA1, MD5 or CRC32. More details are found in the doc/uImage.FIT directory.
5636 Old image format is based on binary files which can be basically anything,
5637 preceded by a special header; see the definitions in include/image.h for
5638 details; basically, the header defines the following image properties:
5640 * Target Operating System (Provisions for OpenBSD, NetBSD, FreeBSD,
5641 4.4BSD, Linux, SVR4, Esix, Solaris, Irix, SCO, Dell, NCR, VxWorks,
5642 LynxOS, pSOS, QNX, RTEMS, INTEGRITY;
5643 Currently supported: Linux, NetBSD, VxWorks, QNX, RTEMS, LynxOS,
5645 * Target CPU Architecture (Provisions for Alpha, ARM, AVR32, Intel x86,
5646 IA64, MIPS, NDS32, Nios II, PowerPC, IBM S390, SuperH, Sparc, Sparc 64 Bit;
5647 Currently supported: ARM, AVR32, Intel x86, MIPS, NDS32, Nios II, PowerPC).
5648 * Compression Type (uncompressed, gzip, bzip2)
5654 The header is marked by a special Magic Number, and both the header
5655 and the data portions of the image are secured against corruption by
5662 Although U-Boot should support any OS or standalone application
5663 easily, the main focus has always been on Linux during the design of
5666 U-Boot includes many features that so far have been part of some
5667 special "boot loader" code within the Linux kernel. Also, any
5668 "initrd" images to be used are no longer part of one big Linux image;
5669 instead, kernel and "initrd" are separate images. This implementation
5670 serves several purposes:
5672 - the same features can be used for other OS or standalone
5673 applications (for instance: using compressed images to reduce the
5674 Flash memory footprint)
5676 - it becomes much easier to port new Linux kernel versions because
5677 lots of low-level, hardware dependent stuff are done by U-Boot
5679 - the same Linux kernel image can now be used with different "initrd"
5680 images; of course this also means that different kernel images can
5681 be run with the same "initrd". This makes testing easier (you don't
5682 have to build a new "zImage.initrd" Linux image when you just
5683 change a file in your "initrd"). Also, a field-upgrade of the
5684 software is easier now.
5690 Porting Linux to U-Boot based systems:
5691 ---------------------------------------
5693 U-Boot cannot save you from doing all the necessary modifications to
5694 configure the Linux device drivers for use with your target hardware
5695 (no, we don't intend to provide a full virtual machine interface to
5698 But now you can ignore ALL boot loader code (in arch/powerpc/mbxboot).
5700 Just make sure your machine specific header file (for instance
5701 include/asm-ppc/tqm8xx.h) includes the same definition of the Board
5702 Information structure as we define in include/asm-<arch>/u-boot.h,
5703 and make sure that your definition of IMAP_ADDR uses the same value
5704 as your U-Boot configuration in CONFIG_SYS_IMMR.
5706 Note that U-Boot now has a driver model, a unified model for drivers.
5707 If you are adding a new driver, plumb it into driver model. If there
5708 is no uclass available, you are encouraged to create one. See
5712 Configuring the Linux kernel:
5713 -----------------------------
5715 No specific requirements for U-Boot. Make sure you have some root
5716 device (initial ramdisk, NFS) for your target system.
5719 Building a Linux Image:
5720 -----------------------
5722 With U-Boot, "normal" build targets like "zImage" or "bzImage" are
5723 not used. If you use recent kernel source, a new build target
5724 "uImage" will exist which automatically builds an image usable by
5725 U-Boot. Most older kernels also have support for a "pImage" target,
5726 which was introduced for our predecessor project PPCBoot and uses a
5727 100% compatible format.
5731 make TQM850L_defconfig
5736 The "uImage" build target uses a special tool (in 'tools/mkimage') to
5737 encapsulate a compressed Linux kernel image with header information,
5738 CRC32 checksum etc. for use with U-Boot. This is what we are doing:
5740 * build a standard "vmlinux" kernel image (in ELF binary format):
5742 * convert the kernel into a raw binary image:
5744 ${CROSS_COMPILE}-objcopy -O binary \
5745 -R .note -R .comment \
5746 -S vmlinux linux.bin
5748 * compress the binary image:
5752 * package compressed binary image for U-Boot:
5754 mkimage -A ppc -O linux -T kernel -C gzip \
5755 -a 0 -e 0 -n "Linux Kernel Image" \
5756 -d linux.bin.gz uImage
5759 The "mkimage" tool can also be used to create ramdisk images for use
5760 with U-Boot, either separated from the Linux kernel image, or
5761 combined into one file. "mkimage" encapsulates the images with a 64
5762 byte header containing information about target architecture,
5763 operating system, image type, compression method, entry points, time
5764 stamp, CRC32 checksums, etc.
5766 "mkimage" can be called in two ways: to verify existing images and
5767 print the header information, or to build new images.
5769 In the first form (with "-l" option) mkimage lists the information
5770 contained in the header of an existing U-Boot image; this includes
5771 checksum verification:
5773 tools/mkimage -l image
5774 -l ==> list image header information
5776 The second form (with "-d" option) is used to build a U-Boot image
5777 from a "data file" which is used as image payload:
5779 tools/mkimage -A arch -O os -T type -C comp -a addr -e ep \
5780 -n name -d data_file image
5781 -A ==> set architecture to 'arch'
5782 -O ==> set operating system to 'os'
5783 -T ==> set image type to 'type'
5784 -C ==> set compression type 'comp'
5785 -a ==> set load address to 'addr' (hex)
5786 -e ==> set entry point to 'ep' (hex)
5787 -n ==> set image name to 'name'
5788 -d ==> use image data from 'datafile'
5790 Right now, all Linux kernels for PowerPC systems use the same load
5791 address (0x00000000), but the entry point address depends on the
5794 - 2.2.x kernels have the entry point at 0x0000000C,
5795 - 2.3.x and later kernels have the entry point at 0x00000000.
5797 So a typical call to build a U-Boot image would read:
5799 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
5800 > -A ppc -O linux -T kernel -C gzip -a 0 -e 0 \
5801 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz \
5802 > examples/uImage.TQM850L
5803 Image Name: 2.4.4 kernel for TQM850L
5804 Created: Wed Jul 19 02:34:59 2000
5805 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5806 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
5807 Load Address: 0x00000000
5808 Entry Point: 0x00000000
5810 To verify the contents of the image (or check for corruption):
5812 -> tools/mkimage -l examples/uImage.TQM850L
5813 Image Name: 2.4.4 kernel for TQM850L
5814 Created: Wed Jul 19 02:34:59 2000
5815 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5816 Data Size: 335725 Bytes = 327.86 kB = 0.32 MB
5817 Load Address: 0x00000000
5818 Entry Point: 0x00000000
5820 NOTE: for embedded systems where boot time is critical you can trade
5821 speed for memory and install an UNCOMPRESSED image instead: this
5822 needs more space in Flash, but boots much faster since it does not
5823 need to be uncompressed:
5825 -> gunzip /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux.gz
5826 -> tools/mkimage -n '2.4.4 kernel for TQM850L' \
5827 > -A ppc -O linux -T kernel -C none -a 0 -e 0 \
5828 > -d /opt/elsk/ppc_8xx/usr/src/linux-2.4.4/arch/powerpc/coffboot/vmlinux \
5829 > examples/uImage.TQM850L-uncompressed
5830 Image Name: 2.4.4 kernel for TQM850L
5831 Created: Wed Jul 19 02:34:59 2000
5832 Image Type: PowerPC Linux Kernel Image (uncompressed)
5833 Data Size: 792160 Bytes = 773.59 kB = 0.76 MB
5834 Load Address: 0x00000000
5835 Entry Point: 0x00000000
5838 Similar you can build U-Boot images from a 'ramdisk.image.gz' file
5839 when your kernel is intended to use an initial ramdisk:
5841 -> tools/mkimage -n 'Simple Ramdisk Image' \
5842 > -A ppc -O linux -T ramdisk -C gzip \
5843 > -d /LinuxPPC/images/SIMPLE-ramdisk.image.gz examples/simple-initrd
5844 Image Name: Simple Ramdisk Image
5845 Created: Wed Jan 12 14:01:50 2000
5846 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
5847 Data Size: 566530 Bytes = 553.25 kB = 0.54 MB
5848 Load Address: 0x00000000
5849 Entry Point: 0x00000000
5851 The "dumpimage" is a tool to disassemble images built by mkimage. Its "-i"
5852 option performs the converse operation of the mkimage's second form (the "-d"
5853 option). Given an image built by mkimage, the dumpimage extracts a "data file"
5856 tools/dumpimage -i image -T type -p position data_file
5857 -i ==> extract from the 'image' a specific 'data_file'
5858 -T ==> set image type to 'type'
5859 -p ==> 'position' (starting at 0) of the 'data_file' inside the 'image'
5862 Installing a Linux Image:
5863 -------------------------
5865 To downloading a U-Boot image over the serial (console) interface,
5866 you must convert the image to S-Record format:
5868 objcopy -I binary -O srec examples/image examples/image.srec
5870 The 'objcopy' does not understand the information in the U-Boot
5871 image header, so the resulting S-Record file will be relative to
5872 address 0x00000000. To load it to a given address, you need to
5873 specify the target address as 'offset' parameter with the 'loads'
5876 Example: install the image to address 0x40100000 (which on the
5877 TQM8xxL is in the first Flash bank):
5879 => erase 40100000 401FFFFF
5885 ## Ready for S-Record download ...
5886 ~>examples/image.srec
5887 1 2 3 4 5 6 7 8 9 10 11 12 13 ...
5889 15989 15990 15991 15992
5890 [file transfer complete]
5892 ## Start Addr = 0x00000000
5895 You can check the success of the download using the 'iminfo' command;
5896 this includes a checksum verification so you can be sure no data
5897 corruption happened:
5901 ## Checking Image at 40100000 ...
5902 Image Name: 2.2.13 for initrd on TQM850L
5903 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5904 Data Size: 335725 Bytes = 327 kB = 0 MB
5905 Load Address: 00000000
5906 Entry Point: 0000000c
5907 Verifying Checksum ... OK
5913 The "bootm" command is used to boot an application that is stored in
5914 memory (RAM or Flash). In case of a Linux kernel image, the contents
5915 of the "bootargs" environment variable is passed to the kernel as
5916 parameters. You can check and modify this variable using the
5917 "printenv" and "setenv" commands:
5920 => printenv bootargs
5921 bootargs=root=/dev/ram
5923 => setenv bootargs root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5925 => printenv bootargs
5926 bootargs=root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5929 ## Booting Linux kernel at 40020000 ...
5930 Image Name: 2.2.13 for NFS on TQM850L
5931 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5932 Data Size: 381681 Bytes = 372 kB = 0 MB
5933 Load Address: 00000000
5934 Entry Point: 0000000c
5935 Verifying Checksum ... OK
5936 Uncompressing Kernel Image ... OK
5937 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:35:17 MEST 2000
5938 Boot arguments: root=/dev/nfs rw nfsroot=10.0.0.2:/LinuxPPC nfsaddrs=10.0.0.99:10.0.0.2
5939 time_init: decrementer frequency = 187500000/60
5940 Calibrating delay loop... 49.77 BogoMIPS
5941 Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000000]
5944 If you want to boot a Linux kernel with initial RAM disk, you pass
5945 the memory addresses of both the kernel and the initrd image (PPBCOOT
5946 format!) to the "bootm" command:
5948 => imi 40100000 40200000
5950 ## Checking Image at 40100000 ...
5951 Image Name: 2.2.13 for initrd on TQM850L
5952 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5953 Data Size: 335725 Bytes = 327 kB = 0 MB
5954 Load Address: 00000000
5955 Entry Point: 0000000c
5956 Verifying Checksum ... OK
5958 ## Checking Image at 40200000 ...
5959 Image Name: Simple Ramdisk Image
5960 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
5961 Data Size: 566530 Bytes = 553 kB = 0 MB
5962 Load Address: 00000000
5963 Entry Point: 00000000
5964 Verifying Checksum ... OK
5966 => bootm 40100000 40200000
5967 ## Booting Linux kernel at 40100000 ...
5968 Image Name: 2.2.13 for initrd on TQM850L
5969 Image Type: PowerPC Linux Kernel Image (gzip compressed)
5970 Data Size: 335725 Bytes = 327 kB = 0 MB
5971 Load Address: 00000000
5972 Entry Point: 0000000c
5973 Verifying Checksum ... OK
5974 Uncompressing Kernel Image ... OK
5975 ## Loading RAMDisk Image at 40200000 ...
5976 Image Name: Simple Ramdisk Image
5977 Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
5978 Data Size: 566530 Bytes = 553 kB = 0 MB
5979 Load Address: 00000000
5980 Entry Point: 00000000
5981 Verifying Checksum ... OK
5982 Loading Ramdisk ... OK
5983 Linux version 2.2.13 (wd@denx.local.net) (gcc version 2.95.2 19991024 (release)) #1 Wed Jul 19 02:32:08 MEST 2000
5984 Boot arguments: root=/dev/ram
5985 time_init: decrementer frequency = 187500000/60
5986 Calibrating delay loop... 49.77 BogoMIPS
5988 RAMDISK: Compressed image found at block 0
5989 VFS: Mounted root (ext2 filesystem).
5993 Boot Linux and pass a flat device tree:
5996 First, U-Boot must be compiled with the appropriate defines. See the section
5997 titled "Linux Kernel Interface" above for a more in depth explanation. The
5998 following is an example of how to start a kernel and pass an updated
6004 oft=oftrees/mpc8540ads.dtb
6005 => tftp $oftaddr $oft
6006 Speed: 1000, full duplex
6008 TFTP from server 192.168.1.1; our IP address is 192.168.1.101
6009 Filename 'oftrees/mpc8540ads.dtb'.
6010 Load address: 0x300000
6013 Bytes transferred = 4106 (100a hex)
6014 => tftp $loadaddr $bootfile
6015 Speed: 1000, full duplex
6017 TFTP from server 192.168.1.1; our IP address is 192.168.1.2
6019 Load address: 0x200000
6020 Loading:############
6022 Bytes transferred = 1029407 (fb51f hex)
6027 => bootm $loadaddr - $oftaddr
6028 ## Booting image at 00200000 ...
6029 Image Name: Linux-2.6.17-dirty
6030 Image Type: PowerPC Linux Kernel Image (gzip compressed)
6031 Data Size: 1029343 Bytes = 1005.2 kB
6032 Load Address: 00000000
6033 Entry Point: 00000000
6034 Verifying Checksum ... OK
6035 Uncompressing Kernel Image ... OK
6036 Booting using flat device tree at 0x300000
6037 Using MPC85xx ADS machine description
6038 Memory CAM mapping: CAM0=256Mb, CAM1=256Mb, CAM2=0Mb residual: 0Mb
6042 More About U-Boot Image Types:
6043 ------------------------------
6045 U-Boot supports the following image types:
6047 "Standalone Programs" are directly runnable in the environment
6048 provided by U-Boot; it is expected that (if they behave
6049 well) you can continue to work in U-Boot after return from
6050 the Standalone Program.
6051 "OS Kernel Images" are usually images of some Embedded OS which
6052 will take over control completely. Usually these programs
6053 will install their own set of exception handlers, device
6054 drivers, set up the MMU, etc. - this means, that you cannot
6055 expect to re-enter U-Boot except by resetting the CPU.
6056 "RAMDisk Images" are more or less just data blocks, and their
6057 parameters (address, size) are passed to an OS kernel that is
6059 "Multi-File Images" contain several images, typically an OS
6060 (Linux) kernel image and one or more data images like
6061 RAMDisks. This construct is useful for instance when you want
6062 to boot over the network using BOOTP etc., where the boot
6063 server provides just a single image file, but you want to get
6064 for instance an OS kernel and a RAMDisk image.
6066 "Multi-File Images" start with a list of image sizes, each
6067 image size (in bytes) specified by an "uint32_t" in network
6068 byte order. This list is terminated by an "(uint32_t)0".
6069 Immediately after the terminating 0 follow the images, one by
6070 one, all aligned on "uint32_t" boundaries (size rounded up to
6071 a multiple of 4 bytes).
6073 "Firmware Images" are binary images containing firmware (like
6074 U-Boot or FPGA images) which usually will be programmed to
6077 "Script files" are command sequences that will be executed by
6078 U-Boot's command interpreter; this feature is especially
6079 useful when you configure U-Boot to use a real shell (hush)
6080 as command interpreter.
6082 Booting the Linux zImage:
6083 -------------------------
6085 On some platforms, it's possible to boot Linux zImage. This is done
6086 using the "bootz" command. The syntax of "bootz" command is the same
6087 as the syntax of "bootm" command.
6089 Note, defining the CONFIG_SUPPORT_RAW_INITRD allows user to supply
6090 kernel with raw initrd images. The syntax is slightly different, the
6091 address of the initrd must be augmented by it's size, in the following
6092 format: "<initrd addres>:<initrd size>".
6098 One of the features of U-Boot is that you can dynamically load and
6099 run "standalone" applications, which can use some resources of
6100 U-Boot like console I/O functions or interrupt services.
6102 Two simple examples are included with the sources:
6107 'examples/hello_world.c' contains a small "Hello World" Demo
6108 application; it is automatically compiled when you build U-Boot.
6109 It's configured to run at address 0x00040004, so you can play with it
6113 ## Ready for S-Record download ...
6114 ~>examples/hello_world.srec
6115 1 2 3 4 5 6 7 8 9 10 11 ...
6116 [file transfer complete]
6118 ## Start Addr = 0x00040004
6120 => go 40004 Hello World! This is a test.
6121 ## Starting application at 0x00040004 ...
6132 Hit any key to exit ...
6134 ## Application terminated, rc = 0x0
6136 Another example, which demonstrates how to register a CPM interrupt
6137 handler with the U-Boot code, can be found in 'examples/timer.c'.
6138 Here, a CPM timer is set up to generate an interrupt every second.
6139 The interrupt service routine is trivial, just printing a '.'
6140 character, but this is just a demo program. The application can be
6141 controlled by the following keys:
6143 ? - print current values og the CPM Timer registers
6144 b - enable interrupts and start timer
6145 e - stop timer and disable interrupts
6146 q - quit application
6149 ## Ready for S-Record download ...
6150 ~>examples/timer.srec
6151 1 2 3 4 5 6 7 8 9 10 11 ...
6152 [file transfer complete]
6154 ## Start Addr = 0x00040004
6157 ## Starting application at 0x00040004 ...
6160 tgcr @ 0xfff00980, tmr @ 0xfff00990, trr @ 0xfff00994, tcr @ 0xfff00998, tcn @ 0xfff0099c, ter @ 0xfff009b0
6163 [q, b, e, ?] Set interval 1000000 us
6166 [q, b, e, ?] ........
6167 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0xef6, ter=0x0
6170 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x2ad4, ter=0x0
6173 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x1efc, ter=0x0
6176 tgcr=0x1, tmr=0xff1c, trr=0x3d09, tcr=0x0, tcn=0x169d, ter=0x0
6178 [q, b, e, ?] ...Stopping timer
6180 [q, b, e, ?] ## Application terminated, rc = 0x0
6186 Over time, many people have reported problems when trying to use the
6187 "minicom" terminal emulation program for serial download. I (wd)
6188 consider minicom to be broken, and recommend not to use it. Under
6189 Unix, I recommend to use C-Kermit for general purpose use (and
6190 especially for kermit binary protocol download ("loadb" command), and
6191 use "cu" for S-Record download ("loads" command). See
6192 http://www.denx.de/wiki/view/DULG/SystemSetup#Section_4.3.
6193 for help with kermit.
6196 Nevertheless, if you absolutely want to use it try adding this
6197 configuration to your "File transfer protocols" section:
6199 Name Program Name U/D FullScr IO-Red. Multi
6200 X kermit /usr/bin/kermit -i -l %l -s Y U Y N N
6201 Y kermit /usr/bin/kermit -i -l %l -r N D Y N N
6207 Starting at version 0.9.2, U-Boot supports NetBSD both as host
6208 (build U-Boot) and target system (boots NetBSD/mpc8xx).
6210 Building requires a cross environment; it is known to work on
6211 NetBSD/i386 with the cross-powerpc-netbsd-1.3 package (you will also
6212 need gmake since the Makefiles are not compatible with BSD make).
6213 Note that the cross-powerpc package does not install include files;
6214 attempting to build U-Boot will fail because <machine/ansi.h> is
6215 missing. This file has to be installed and patched manually:
6217 # cd /usr/pkg/cross/powerpc-netbsd/include
6219 # ln -s powerpc machine
6220 # cp /usr/src/sys/arch/powerpc/include/ansi.h powerpc/ansi.h
6221 # ${EDIT} powerpc/ansi.h ## must remove __va_list, _BSD_VA_LIST
6223 Native builds *don't* work due to incompatibilities between native
6224 and U-Boot include files.
6226 Booting assumes that (the first part of) the image booted is a
6227 stage-2 loader which in turn loads and then invokes the kernel
6228 proper. Loader sources will eventually appear in the NetBSD source
6229 tree (probably in sys/arc/mpc8xx/stand/u-boot_stage2/); in the
6230 meantime, see ftp://ftp.denx.de/pub/u-boot/ppcboot_stage2.tar.gz
6233 Implementation Internals:
6234 =========================
6236 The following is not intended to be a complete description of every
6237 implementation detail. However, it should help to understand the
6238 inner workings of U-Boot and make it easier to port it to custom
6242 Initial Stack, Global Data:
6243 ---------------------------
6245 The implementation of U-Boot is complicated by the fact that U-Boot
6246 starts running out of ROM (flash memory), usually without access to
6247 system RAM (because the memory controller is not initialized yet).
6248 This means that we don't have writable Data or BSS segments, and BSS
6249 is not initialized as zero. To be able to get a C environment working
6250 at all, we have to allocate at least a minimal stack. Implementation
6251 options for this are defined and restricted by the CPU used: Some CPU
6252 models provide on-chip memory (like the IMMR area on MPC8xx and
6253 MPC826x processors), on others (parts of) the data cache can be
6254 locked as (mis-) used as memory, etc.
6256 Chris Hallinan posted a good summary of these issues to the
6257 U-Boot mailing list:
6259 Subject: RE: [U-Boot-Users] RE: More On Memory Bank x (nothingness)?
6260 From: "Chris Hallinan" <clh@net1plus.com>
6261 Date: Mon, 10 Feb 2003 16:43:46 -0500 (22:43 MET)
6264 Correct me if I'm wrong, folks, but the way I understand it
6265 is this: Using DCACHE as initial RAM for Stack, etc, does not
6266 require any physical RAM backing up the cache. The cleverness
6267 is that the cache is being used as a temporary supply of
6268 necessary storage before the SDRAM controller is setup. It's
6269 beyond the scope of this list to explain the details, but you
6270 can see how this works by studying the cache architecture and
6271 operation in the architecture and processor-specific manuals.
6273 OCM is On Chip Memory, which I believe the 405GP has 4K. It
6274 is another option for the system designer to use as an
6275 initial stack/RAM area prior to SDRAM being available. Either
6276 option should work for you. Using CS 4 should be fine if your
6277 board designers haven't used it for something that would
6278 cause you grief during the initial boot! It is frequently not
6281 CONFIG_SYS_INIT_RAM_ADDR should be somewhere that won't interfere
6282 with your processor/board/system design. The default value
6283 you will find in any recent u-boot distribution in
6284 walnut.h should work for you. I'd set it to a value larger
6285 than your SDRAM module. If you have a 64MB SDRAM module, set
6286 it above 400_0000. Just make sure your board has no resources
6287 that are supposed to respond to that address! That code in
6288 start.S has been around a while and should work as is when
6289 you get the config right.
6294 It is essential to remember this, since it has some impact on the C
6295 code for the initialization procedures:
6297 * Initialized global data (data segment) is read-only. Do not attempt
6300 * Do not use any uninitialized global data (or implicitly initialized
6301 as zero data - BSS segment) at all - this is undefined, initiali-
6302 zation is performed later (when relocating to RAM).
6304 * Stack space is very limited. Avoid big data buffers or things like
6307 Having only the stack as writable memory limits means we cannot use
6308 normal global data to share information between the code. But it
6309 turned out that the implementation of U-Boot can be greatly
6310 simplified by making a global data structure (gd_t) available to all
6311 functions. We could pass a pointer to this data as argument to _all_
6312 functions, but this would bloat the code. Instead we use a feature of
6313 the GCC compiler (Global Register Variables) to share the data: we
6314 place a pointer (gd) to the global data into a register which we
6315 reserve for this purpose.
6317 When choosing a register for such a purpose we are restricted by the
6318 relevant (E)ABI specifications for the current architecture, and by
6319 GCC's implementation.
6321 For PowerPC, the following registers have specific use:
6323 R2: reserved for system use
6324 R3-R4: parameter passing and return values
6325 R5-R10: parameter passing
6326 R13: small data area pointer
6330 (U-Boot also uses R12 as internal GOT pointer. r12
6331 is a volatile register so r12 needs to be reset when
6332 going back and forth between asm and C)
6334 ==> U-Boot will use R2 to hold a pointer to the global data
6336 Note: on PPC, we could use a static initializer (since the
6337 address of the global data structure is known at compile time),
6338 but it turned out that reserving a register results in somewhat
6339 smaller code - although the code savings are not that big (on
6340 average for all boards 752 bytes for the whole U-Boot image,
6341 624 text + 127 data).
6343 On Blackfin, the normal C ABI (except for P3) is followed as documented here:
6344 http://docs.blackfin.uclinux.org/doku.php?id=application_binary_interface
6346 ==> U-Boot will use P3 to hold a pointer to the global data
6348 On ARM, the following registers are used:
6350 R0: function argument word/integer result
6351 R1-R3: function argument word
6352 R9: platform specific
6353 R10: stack limit (used only if stack checking is enabled)
6354 R11: argument (frame) pointer
6355 R12: temporary workspace
6358 R15: program counter
6360 ==> U-Boot will use R9 to hold a pointer to the global data
6362 Note: on ARM, only R_ARM_RELATIVE relocations are supported.
6364 On Nios II, the ABI is documented here:
6365 http://www.altera.com/literature/hb/nios2/n2cpu_nii51016.pdf
6367 ==> U-Boot will use gp to hold a pointer to the global data
6369 Note: on Nios II, we give "-G0" option to gcc and don't use gp
6370 to access small data sections, so gp is free.
6372 On NDS32, the following registers are used:
6374 R0-R1: argument/return
6376 R15: temporary register for assembler
6377 R16: trampoline register
6378 R28: frame pointer (FP)
6379 R29: global pointer (GP)
6380 R30: link register (LP)
6381 R31: stack pointer (SP)
6382 PC: program counter (PC)
6384 ==> U-Boot will use R10 to hold a pointer to the global data
6386 NOTE: DECLARE_GLOBAL_DATA_PTR must be used with file-global scope,
6387 or current versions of GCC may "optimize" the code too much.
6392 U-Boot runs in system state and uses physical addresses, i.e. the
6393 MMU is not used either for address mapping nor for memory protection.
6395 The available memory is mapped to fixed addresses using the memory
6396 controller. In this process, a contiguous block is formed for each
6397 memory type (Flash, SDRAM, SRAM), even when it consists of several
6398 physical memory banks.
6400 U-Boot is installed in the first 128 kB of the first Flash bank (on
6401 TQM8xxL modules this is the range 0x40000000 ... 0x4001FFFF). After
6402 booting and sizing and initializing DRAM, the code relocates itself
6403 to the upper end of DRAM. Immediately below the U-Boot code some
6404 memory is reserved for use by malloc() [see CONFIG_SYS_MALLOC_LEN
6405 configuration setting]. Below that, a structure with global Board
6406 Info data is placed, followed by the stack (growing downward).
6408 Additionally, some exception handler code is copied to the low 8 kB
6409 of DRAM (0x00000000 ... 0x00001FFF).
6411 So a typical memory configuration with 16 MB of DRAM could look like
6414 0x0000 0000 Exception Vector code
6417 0x0000 2000 Free for Application Use
6423 0x00FB FF20 Monitor Stack (Growing downward)
6424 0x00FB FFAC Board Info Data and permanent copy of global data
6425 0x00FC 0000 Malloc Arena
6428 0x00FE 0000 RAM Copy of Monitor Code
6429 ... eventually: LCD or video framebuffer
6430 ... eventually: pRAM (Protected RAM - unchanged by reset)
6431 0x00FF FFFF [End of RAM]
6434 System Initialization:
6435 ----------------------
6437 In the reset configuration, U-Boot starts at the reset entry point
6438 (on most PowerPC systems at address 0x00000100). Because of the reset
6439 configuration for CS0# this is a mirror of the on board Flash memory.
6440 To be able to re-map memory U-Boot then jumps to its link address.
6441 To be able to implement the initialization code in C, a (small!)
6442 initial stack is set up in the internal Dual Ported RAM (in case CPUs
6443 which provide such a feature like MPC8xx or MPC8260), or in a locked
6444 part of the data cache. After that, U-Boot initializes the CPU core,
6445 the caches and the SIU.
6447 Next, all (potentially) available memory banks are mapped using a
6448 preliminary mapping. For example, we put them on 512 MB boundaries
6449 (multiples of 0x20000000: SDRAM on 0x00000000 and 0x20000000, Flash
6450 on 0x40000000 and 0x60000000, SRAM on 0x80000000). Then UPM A is
6451 programmed for SDRAM access. Using the temporary configuration, a
6452 simple memory test is run that determines the size of the SDRAM
6455 When there is more than one SDRAM bank, and the banks are of
6456 different size, the largest is mapped first. For equal size, the first
6457 bank (CS2#) is mapped first. The first mapping is always for address
6458 0x00000000, with any additional banks following immediately to create
6459 contiguous memory starting from 0.
6461 Then, the monitor installs itself at the upper end of the SDRAM area
6462 and allocates memory for use by malloc() and for the global Board
6463 Info data; also, the exception vector code is copied to the low RAM
6464 pages, and the final stack is set up.
6466 Only after this relocation will you have a "normal" C environment;
6467 until that you are restricted in several ways, mostly because you are
6468 running from ROM, and because the code will have to be relocated to a
6472 U-Boot Porting Guide:
6473 ----------------------
6475 [Based on messages by Jerry Van Baren in the U-Boot-Users mailing
6479 int main(int argc, char *argv[])
6481 sighandler_t no_more_time;
6483 signal(SIGALRM, no_more_time);
6484 alarm(PROJECT_DEADLINE - toSec (3 * WEEK));
6486 if (available_money > available_manpower) {
6487 Pay consultant to port U-Boot;
6491 Download latest U-Boot source;
6493 Subscribe to u-boot mailing list;
6496 email("Hi, I am new to U-Boot, how do I get started?");
6499 Read the README file in the top level directory;
6500 Read http://www.denx.de/twiki/bin/view/DULG/Manual;
6501 Read applicable doc/*.README;
6502 Read the source, Luke;
6503 /* find . -name "*.[chS]" | xargs grep -i <keyword> */
6506 if (available_money > toLocalCurrency ($2500))
6509 Add a lot of aggravation and time;
6511 if (a similar board exists) { /* hopefully... */
6512 cp -a board/<similar> board/<myboard>
6513 cp include/configs/<similar>.h include/configs/<myboard>.h
6515 Create your own board support subdirectory;
6516 Create your own board include/configs/<myboard>.h file;
6518 Edit new board/<myboard> files
6519 Edit new include/configs/<myboard>.h
6524 Add / modify source code;
6528 email("Hi, I am having problems...");
6530 Send patch file to the U-Boot email list;
6531 if (reasonable critiques)
6532 Incorporate improvements from email list code review;
6534 Defend code as written;
6540 void no_more_time (int sig)
6549 All contributions to U-Boot should conform to the Linux kernel
6550 coding style; see the file "Documentation/CodingStyle" and the script
6551 "scripts/Lindent" in your Linux kernel source directory.
6553 Source files originating from a different project (for example the
6554 MTD subsystem) are generally exempt from these guidelines and are not
6555 reformatted to ease subsequent migration to newer versions of those
6558 Please note that U-Boot is implemented in C (and to some small parts in
6559 Assembler); no C++ is used, so please do not use C++ style comments (//)
6562 Please also stick to the following formatting rules:
6563 - remove any trailing white space
6564 - use TAB characters for indentation and vertical alignment, not spaces
6565 - make sure NOT to use DOS '\r\n' line feeds
6566 - do not add more than 2 consecutive empty lines to source files
6567 - do not add trailing empty lines to source files
6569 Submissions which do not conform to the standards may be returned
6570 with a request to reformat the changes.
6576 Since the number of patches for U-Boot is growing, we need to
6577 establish some rules. Submissions which do not conform to these rules
6578 may be rejected, even when they contain important and valuable stuff.
6580 Please see http://www.denx.de/wiki/U-Boot/Patches for details.
6582 Patches shall be sent to the u-boot mailing list <u-boot@lists.denx.de>;
6583 see http://lists.denx.de/mailman/listinfo/u-boot
6585 When you send a patch, please include the following information with
6588 * For bug fixes: a description of the bug and how your patch fixes
6589 this bug. Please try to include a way of demonstrating that the
6590 patch actually fixes something.
6592 * For new features: a description of the feature and your
6595 * A CHANGELOG entry as plaintext (separate from the patch)
6597 * For major contributions, your entry to the CREDITS file
6599 * When you add support for a new board, don't forget to add a
6600 maintainer e-mail address to the boards.cfg file, too.
6602 * If your patch adds new configuration options, don't forget to
6603 document these in the README file.
6605 * The patch itself. If you are using git (which is *strongly*
6606 recommended) you can easily generate the patch using the
6607 "git format-patch". If you then use "git send-email" to send it to
6608 the U-Boot mailing list, you will avoid most of the common problems
6609 with some other mail clients.
6611 If you cannot use git, use "diff -purN OLD NEW". If your version of
6612 diff does not support these options, then get the latest version of
6615 The current directory when running this command shall be the parent
6616 directory of the U-Boot source tree (i. e. please make sure that
6617 your patch includes sufficient directory information for the
6620 We prefer patches as plain text. MIME attachments are discouraged,
6621 and compressed attachments must not be used.
6623 * If one logical set of modifications affects or creates several
6624 files, all these changes shall be submitted in a SINGLE patch file.
6626 * Changesets that contain different, unrelated modifications shall be
6627 submitted as SEPARATE patches, one patch per changeset.
6632 * Before sending the patch, run the MAKEALL script on your patched
6633 source tree and make sure that no errors or warnings are reported
6634 for any of the boards.
6636 * Keep your modifications to the necessary minimum: A patch
6637 containing several unrelated changes or arbitrary reformats will be
6638 returned with a request to re-formatting / split it.
6640 * If you modify existing code, make sure that your new code does not
6641 add to the memory footprint of the code ;-) Small is beautiful!
6642 When adding new features, these should compile conditionally only
6643 (using #ifdef), and the resulting code with the new feature
6644 disabled must not need more memory than the old code without your
6647 * Remember that there is a size limit of 100 kB per message on the
6648 u-boot mailing list. Bigger patches will be moderated. If they are
6649 reasonable and not too big, they will be acknowledged. But patches
6650 bigger than the size limit should be avoided.
projects / people / ms / u-boot.git / blob