arch/arm/Kconfig

   1 menu "ARM architecture"
   2         depends on ARM
   3
   4 config SYS_ARCH
   5         default "arm"
   6
   7 config ARM64
   8         bool
   9         select PHYS_64BIT
  10         select SYS_CACHE_SHIFT_6
  11
  12 if ARM64
  13 config POSITION_INDEPENDENT
  14         bool "Generate position-independent pre-relocation code"
  15         help
  16           U-Boot expects to be linked to a specific hard-coded address, and to
  17           be loaded to and run from that address. This option lifts that
  18           restriction, thus allowing the code to be loaded to and executed
  19           from almost any address. This logic relies on the relocation
  20           information that is embedded into the binary to support U-Boot
  21           relocating itself to the top-of-RAM later during execution.
  22
  23 config SYS_INIT_SP_BSS_OFFSET
  24         int
  25         help
  26           U-Boot typically uses a hard-coded value for the stack pointer
  27           before relocation. Define this option to instead calculate the
  28           initial SP at run-time. This is useful to avoid hard-coding addresses
  29           into U-Boot, so that can be loaded and executed at arbitrary
  30           addresses and thus avoid using arbitrary addresses at runtime. This
  31           option's value is the offset added to &_bss_start in order to
  32           calculate the stack pointer. This offset should be large enough so
  33           that the early malloc region, global data (gd), and early stack usage
  34           do not overlap any appended DTB.
  35
  36 config LINUX_KERNEL_IMAGE_HEADER
  37         bool
  38         help
  39           Place a Linux kernel image header at the start of the U-Boot binary.
  40           The format of the header is described in the Linux kernel source at
  41           Documentation/arm64/booting.txt. This feature is useful since the
  42           image header reports the amount of memory (BSS and similar) that
  43           U-Boot needs to use, but which isn't part of the binary.
  44
  45 if LINUX_KERNEL_IMAGE_HEADER
  46 config LNX_KRNL_IMG_TEXT_OFFSET_BASE
  47         hex
  48         help
  49           The value subtracted from CONFIG_SYS_TEXT_BASE to calculate the
  50           TEXT_OFFSET value written in to the Linux kernel image header.
  51 endif
  52 endif
  53
  54 config STATIC_RELA
  55         bool
  56         default y if ARM64 && !POSITION_INDEPENDENT
  57
  58 config DMA_ADDR_T_64BIT
  59         bool
  60         default y if ARM64
  61
  62 config HAS_VBAR
  63         bool
  64
  65 config HAS_THUMB2
  66         bool
  67
  68 # Used for compatibility with asm files copied from the kernel
  69 config ARM_ASM_UNIFIED
  70         bool
  71         default y
  72
  73 # Used for compatibility with asm files copied from the kernel
  74 config THUMB2_KERNEL
  75         bool
  76
  77 config SYS_ARM_CACHE_CP15
  78         bool "CP15 based cache enabling support"
  79         help
  80           Select this if your processor suports enabling caches by using
  81           CP15 registers.
  82
  83 config SYS_ARM_MMU
  84         bool "MMU-based Paged Memory Management Support"
  85         select SYS_ARM_CACHE_CP15
  86         help
  87           Select if you want MMU-based virtualised addressing space
  88           support by paged memory management.
  89
  90 config SYS_ARM_MPU
  91         bool 'Use the ARM v7 PMSA Compliant MPU'
  92         help
  93           Some ARM systems without an MMU have instead a Memory Protection
  94           Unit (MPU) that defines the type and permissions for regions of
  95           memory.
  96           If your CPU has an MPU then you should choose 'y' here unless you
  97           know that you do not want to use the MPU.
  98
  99 # If set, the workarounds for these ARM errata are applied early during U-Boot
 100 # startup. Note that in general these options force the workarounds to be
 101 # applied; no CPU-type/version detection exists, unlike the similar options in
 102 # the Linux kernel. Do not set these options unless they apply!  Also note that
 103 # the following can be machine specific errata. These do have ability to
 104 # provide rudimentary version and machine specific checks, but expect no
 105 # product checks:
 106 # CONFIG_ARM_ERRATA_430973
 107 # CONFIG_ARM_ERRATA_454179
 108 # CONFIG_ARM_ERRATA_621766
 109 # CONFIG_ARM_ERRATA_798870
 110 # CONFIG_ARM_ERRATA_801819
 111 config ARM_ERRATA_430973
 112         bool
 113
 114 config ARM_ERRATA_454179
 115         bool
 116
 117 config ARM_ERRATA_621766
 118         bool
 119
 120 config ARM_ERRATA_716044
 121         bool
 122
 123 config ARM_ERRATA_725233
 124         bool
 125
 126 config ARM_ERRATA_742230
 127         bool
 128
 129 config ARM_ERRATA_743622
 130         bool
 131
 132 config ARM_ERRATA_751472
 133         bool
 134
 135 config ARM_ERRATA_761320
 136         bool
 137
 138 config ARM_ERRATA_773022
 139         bool
 140
 141 config ARM_ERRATA_774769
 142         bool
 143
 144 config ARM_ERRATA_794072
 145         bool
 146
 147 config ARM_ERRATA_798870
 148         bool
 149
 150 config ARM_ERRATA_801819
 151         bool
 152
 153 config ARM_ERRATA_826974
 154         bool
 155
 156 config ARM_ERRATA_828024
 157         bool
 158
 159 config ARM_ERRATA_829520
 160         bool
 161
 162 config ARM_ERRATA_833069
 163         bool
 164
 165 config ARM_ERRATA_833471
 166         bool
 167
 168 config ARM_ERRATA_845369
 169        bool
 170
 171 config ARM_ERRATA_852421
 172         bool
 173
 174 config ARM_ERRATA_852423
 175         bool
 176
 177 config ARM_ERRATA_855873
 178         bool
 179
 180 config CPU_ARM720T
 181         bool
 182         select SYS_CACHE_SHIFT_5
 183         imply SYS_ARM_MMU
 184
 185 config CPU_ARM920T
 186         bool
 187         select SYS_CACHE_SHIFT_5
 188         imply SYS_ARM_MMU
 189
 190 config CPU_ARM926EJS
 191         bool
 192         select SYS_CACHE_SHIFT_5
 193         imply SYS_ARM_MMU
 194
 195 config CPU_ARM946ES
 196         bool
 197         select SYS_CACHE_SHIFT_5
 198         imply SYS_ARM_MMU
 199
 200 config CPU_ARM1136
 201         bool
 202         select SYS_CACHE_SHIFT_5
 203         imply SYS_ARM_MMU
 204
 205 config CPU_ARM1176
 206         bool
 207         select HAS_VBAR
 208         select SYS_CACHE_SHIFT_5
 209         imply SYS_ARM_MMU
 210
 211 config CPU_V7A
 212         bool
 213         select HAS_VBAR
 214         select HAS_THUMB2
 215         select SYS_CACHE_SHIFT_6
 216         imply SYS_ARM_MMU
 217
 218 config CPU_V7M
 219         bool
 220         select HAS_THUMB2
 221         select THUMB2_KERNEL
 222         select SYS_CACHE_SHIFT_5
 223         select SYS_ARM_MPU
 224
 225 config CPU_V7R
 226         bool
 227         select HAS_THUMB2
 228         select SYS_CACHE_SHIFT_6
 229         select SYS_ARM_MPU
 230         select SYS_ARM_CACHE_CP15
 231
 232 config CPU_PXA
 233         bool
 234         select SYS_CACHE_SHIFT_5
 235         imply SYS_ARM_MMU
 236
 237 config CPU_SA1100
 238         bool
 239         select SYS_CACHE_SHIFT_5
 240         imply SYS_ARM_MMU
 241
 242 config SYS_CPU
 243         default "arm720t" if CPU_ARM720T
 244         default "arm920t" if CPU_ARM920T
 245         default "arm926ejs" if CPU_ARM926EJS
 246         default "arm946es" if CPU_ARM946ES
 247         default "arm1136" if CPU_ARM1136
 248         default "arm1176" if CPU_ARM1176
 249         default "armv7" if CPU_V7A
 250         default "armv7" if CPU_V7R
 251         default "armv7m" if CPU_V7M
 252         default "pxa" if CPU_PXA
 253         default "sa1100" if CPU_SA1100
 254         default "armv8" if ARM64
 255
 256 config SYS_ARM_ARCH
 257         int
 258         default 4 if CPU_ARM720T
 259         default 4 if CPU_ARM920T
 260         default 5 if CPU_ARM926EJS
 261         default 5 if CPU_ARM946ES
 262         default 6 if CPU_ARM1136
 263         default 6 if CPU_ARM1176
 264         default 7 if CPU_V7A
 265         default 7 if CPU_V7M
 266         default 7 if CPU_V7R
 267         default 5 if CPU_PXA
 268         default 4 if CPU_SA1100
 269         default 8 if ARM64
 270
 271 config SYS_CACHE_SHIFT_5
 272         bool
 273
 274 config SYS_CACHE_SHIFT_6
 275         bool
 276
 277 config SYS_CACHE_SHIFT_7
 278         bool
 279
 280 config SYS_CACHELINE_SIZE
 281         int
 282         default 128 if SYS_CACHE_SHIFT_7
 283         default 64 if SYS_CACHE_SHIFT_6
 284         default 32 if SYS_CACHE_SHIFT_5
 285
 286 config SYS_ARCH_TIMER
 287         bool "ARM Generic Timer support"
 288         depends on CPU_V7A || ARM64
 289         default y if ARM64
 290         help
 291           The ARM Generic Timer (aka arch-timer) provides an architected
 292           interface to a timer source on an SoC.
 293           It is mandantory for ARMv8 implementation and widely available
 294           on ARMv7 systems.
 295
 296 config ARM_SMCCC
 297         bool "Support for ARM SMC Calling Convention (SMCCC)"
 298         depends on CPU_V7A || ARM64
 299         select ARM_PSCI_FW
 300         help
 301           Say Y here if you want to enable ARM SMC Calling Convention.
 302           This should be enabled if U-Boot needs to communicate with system
 303           firmware (for example, PSCI) according to SMCCC.
 304
 305 config SEMIHOSTING
 306         bool "support boot from semihosting"
 307         help
 308           In emulated environments, semihosting is a way for
 309           the hosted environment to call out to the emulator to
 310           retrieve files from the host machine.
 311
 312 config SYS_THUMB_BUILD
 313         bool "Build U-Boot using the Thumb instruction set"
 314         depends on !ARM64
 315         help
 316            Use this flag to build U-Boot using the Thumb instruction set for
 317            ARM architectures. Thumb instruction set provides better code
 318            density. For ARM architectures that support Thumb2 this flag will
 319            result in Thumb2 code generated by GCC.
 320
 321 config SPL_SYS_THUMB_BUILD
 322         bool "Build SPL using the Thumb instruction set"
 323         default y if SYS_THUMB_BUILD
 324         depends on !ARM64
 325         help
 326            Use this flag to build SPL using the Thumb instruction set for
 327            ARM architectures. Thumb instruction set provides better code
 328            density. For ARM architectures that support Thumb2 this flag will
 329            result in Thumb2 code generated by GCC.
 330
 331 config SYS_L2CACHE_OFF
 332         bool "L2cache off"
 333         help
 334           If SoC does not support L2CACHE or one do not want to enable
 335           L2CACHE, choose this option.
 336
 337 config ENABLE_ARM_SOC_BOOT0_HOOK
 338         bool "prepare BOOT0 header"
 339         help
 340           If the SoC's BOOT0 requires a header area filled with (magic)
 341           values, then choose this option, and create a file included as
 342           <asm/arch/boot0.h> which contains the required assembler code.
 343
 344 config ARM_CORTEX_CPU_IS_UP
 345         bool
 346         default n
 347
 348 config USE_ARCH_MEMCPY
 349         bool "Use an assembly optimized implementation of memcpy"
 350         default y
 351         depends on !ARM64
 352         help
 353           Enable the generation of an optimized version of memcpy.
 354           Such implementation may be faster under some conditions
 355           but may increase the binary size.
 356
 357 config SPL_USE_ARCH_MEMCPY
 358         bool "Use an assembly optimized implementation of memcpy for SPL"
 359         default y if USE_ARCH_MEMCPY
 360         depends on !ARM64
 361         help
 362           Enable the generation of an optimized version of memcpy.
 363           Such implementation may be faster under some conditions
 364           but may increase the binary size.
 365
 366 config USE_ARCH_MEMSET
 367         bool "Use an assembly optimized implementation of memset"
 368         default y
 369         depends on !ARM64
 370         help
 371           Enable the generation of an optimized version of memset.
 372           Such implementation may be faster under some conditions
 373           but may increase the binary size.
 374
 375 config SPL_USE_ARCH_MEMSET
 376         bool "Use an assembly optimized implementation of memset for SPL"
 377         default y if USE_ARCH_MEMSET
 378         depends on !ARM64
 379         help
 380           Enable the generation of an optimized version of memset.
 381           Such implementation may be faster under some conditions
 382           but may increase the binary size.
 383
 384 config ARM64_SUPPORT_AARCH32
 385         bool "ARM64 system support AArch32 execution state"
 386         default y if ARM64 && !TARGET_THUNDERX_88XX
 387         help
 388           This ARM64 system supports AArch32 execution state.
 389
 390 choice
 391         prompt "Target select"
 392         default TARGET_HIKEY
 393
 394 config ARCH_AT91
 395         bool "Atmel AT91"
 396         select SPL_BOARD_INIT if SPL
 397
 398 config TARGET_EDB93XX
 399         bool "Support edb93xx"
 400         select CPU_ARM920T
 401         select PL010_SERIAL
 402
 403 config TARGET_ASPENITE
 404         bool "Support aspenite"
 405         select CPU_ARM926EJS
 406
 407 config TARGET_GPLUGD
 408         bool "Support gplugd"
 409         select CPU_ARM926EJS
 410
 411 config ARCH_DAVINCI
 412         bool "TI DaVinci"
 413         select CPU_ARM926EJS
 414         imply CMD_SAVES
 415         help
 416           Support for TI's DaVinci platform.
 417
 418 config KIRKWOOD
 419         bool "Marvell Kirkwood"
 420         select CPU_ARM926EJS
 421         select BOARD_EARLY_INIT_F
 422         select ARCH_MISC_INIT
 423
 424 config ARCH_MVEBU
 425         bool "Marvell MVEBU family (Armada XP/375/38x/3700/7K/8K)"
 426         select OF_CONTROL
 427         select OF_SEPARATE
 428         select DM
 429         select DM_ETH
 430         select DM_SERIAL
 431         select DM_SPI
 432         select DM_SPI_FLASH
 433         select SPI
 434
 435 config TARGET_DEVKIT3250
 436         bool "Support devkit3250"
 437         select CPU_ARM926EJS
 438         select SUPPORT_SPL
 439
 440 config TARGET_WORK_92105
 441         bool "Support work_92105"
 442         select CPU_ARM926EJS
 443         select SUPPORT_SPL
 444
 445 config TARGET_APF27
 446         bool "Support apf27"
 447         select CPU_ARM926EJS
 448         select SUPPORT_SPL
 449
 450 config ORION5X
 451         bool "Marvell Orion"
 452         select CPU_ARM926EJS
 453
 454 config TARGET_SPEAR300
 455         bool "Support spear300"
 456         select CPU_ARM926EJS
 457         select BOARD_EARLY_INIT_F
 458         imply CMD_SAVES
 459         select PL011_SERIAL
 460
 461 config TARGET_SPEAR310
 462         bool "Support spear310"
 463         select CPU_ARM926EJS
 464         select BOARD_EARLY_INIT_F
 465         imply CMD_SAVES
 466         select PL011_SERIAL
 467
 468 config TARGET_SPEAR320
 469         bool "Support spear320"
 470         select CPU_ARM926EJS
 471         select BOARD_EARLY_INIT_F
 472         imply CMD_SAVES
 473         select PL011_SERIAL
 474
 475 config TARGET_SPEAR600
 476         bool "Support spear600"
 477         select CPU_ARM926EJS
 478         select BOARD_EARLY_INIT_F
 479         imply CMD_SAVES
 480         select PL011_SERIAL
 481
 482 config TARGET_STV0991
 483         bool "Support stv0991"
 484         select CPU_V7A
 485         select DM
 486         select DM_SERIAL
 487         select DM_SPI
 488         select DM_SPI_FLASH
 489         select SPI
 490         select SPI_FLASH
 491         select PL01X_SERIAL
 492
 493 config TARGET_X600
 494         bool "Support x600"
 495         select BOARD_LATE_INIT
 496         select CPU_ARM926EJS
 497         select SUPPORT_SPL
 498         select PL011_SERIAL
 499
 500 config TARGET_WOODBURN
 501         bool "Support woodburn"
 502         select CPU_ARM1136
 503
 504 config TARGET_WOODBURN_SD
 505         bool "Support woodburn_sd"
 506         select CPU_ARM1136
 507         select SUPPORT_SPL
 508
 509 config TARGET_FLEA3
 510         bool "Support flea3"
 511         select CPU_ARM1136
 512
 513 config TARGET_MX35PDK
 514         bool "Support mx35pdk"
 515         select BOARD_LATE_INIT
 516         select CPU_ARM1136
 517
 518 config ARCH_BCM283X
 519         bool "Broadcom BCM283X family"
 520         select DM
 521         select DM_SERIAL
 522         select DM_GPIO
 523         select OF_CONTROL
 524         select PL01X_SERIAL
 525         select SERIAL_SEARCH_ALL
 526         imply FAT_WRITE
 527
 528 config TARGET_VEXPRESS_CA15_TC2
 529         bool "Support vexpress_ca15_tc2"
 530         select CPU_V7A
 531         select CPU_V7_HAS_NONSEC
 532         select CPU_V7_HAS_VIRT
 533         select PL011_SERIAL
 534
 535 config TARGET_VEXPRESS_CA5X2
 536         bool "Support vexpress_ca5x2"
 537         select CPU_V7A
 538         select PL011_SERIAL
 539
 540 config TARGET_VEXPRESS_CA9X4
 541         bool "Support vexpress_ca9x4"
 542         select CPU_V7A
 543         select PL011_SERIAL
 544
 545 config TARGET_BCM23550_W1D
 546         bool "Support bcm23550_w1d"
 547         select CPU_V7A
 548         imply CRC32_VERIFY
 549         imply FAT_WRITE
 550
 551 config TARGET_BCM28155_AP
 552         bool "Support bcm28155_ap"
 553         select CPU_V7A
 554         imply CRC32_VERIFY
 555         imply FAT_WRITE
 556
 557 config TARGET_BCMCYGNUS
 558         bool "Support bcmcygnus"
 559         select CPU_V7A
 560         imply CRC32_VERIFY
 561         imply CMD_HASH
 562         imply FAT_WRITE
 563         imply HASH_VERIFY
 564         imply NETDEVICES
 565         imply BCM_SF2_ETH
 566         imply BCM_SF2_ETH_GMAC
 567
 568 config TARGET_BCMNSP
 569         bool "Support bcmnsp"
 570         select CPU_V7A
 571
 572 config TARGET_BCMNS2
 573         bool "Support Broadcom Northstar2"
 574         select ARM64
 575         help
 576           Support for Broadcom Northstar 2 SoCs.  NS2 is a quad-core 64-bit
 577           ARMv8 Cortex-A57 processors targeting a broad range of networking
 578           applications
 579
 580 config ARCH_EXYNOS
 581         bool "Samsung EXYNOS"
 582         select DM
 583         select DM_I2C
 584         select DM_SPI_FLASH
 585         select DM_SERIAL
 586         select DM_SPI
 587         select DM_GPIO
 588         select DM_KEYBOARD
 589         select SPI
 590         imply FAT_WRITE
 591
 592 config ARCH_S5PC1XX
 593         bool "Samsung S5PC1XX"
 594         select CPU_V7A
 595         select DM
 596         select DM_SERIAL
 597         select DM_GPIO
 598         select DM_I2C
 599
 600 config ARCH_HIGHBANK
 601         bool "Calxeda Highbank"
 602         select CPU_V7A
 603         select PL011_SERIAL
 604
 605 config ARCH_INTEGRATOR
 606         bool "ARM Ltd. Integrator family"
 607         select DM
 608         select DM_SERIAL
 609         select PL01X_SERIAL
 610
 611 config ARCH_KEYSTONE
 612         bool "TI Keystone"
 613         select CPU_V7A
 614         select SUPPORT_SPL
 615         select SYS_THUMB_BUILD
 616         select CMD_POWEROFF
 617         select SYS_ARCH_TIMER
 618         imply CMD_MTDPARTS
 619         imply FIT
 620         imply CMD_SAVES
 621
 622 config ARCH_OMAP2PLUS
 623         bool "TI OMAP2+"
 624         select CPU_V7A
 625         select SPL_BOARD_INIT if SPL
 626         select SPL_STACK_R if SPL
 627         select SUPPORT_SPL
 628         imply FIT
 629
 630 config ARCH_MESON
 631         bool "Amlogic Meson"
 632         imply DISTRO_DEFAULTS
 633         help
 634           Support for the Meson SoC family developed by Amlogic Inc.,
 635           targeted at media players and tablet computers. We currently
 636           support the S905 (GXBaby) 64-bit SoC.
 637
 638 config ARCH_MX8M
 639         bool "NXP i.MX8M platform"
 640         select ARM64
 641         select DM
 642         select SUPPORT_SPL
 643
 644 config ARCH_MX23
 645         bool "NXP i.MX23 family"
 646         select CPU_ARM926EJS
 647         select PL011_SERIAL
 648         select SUPPORT_SPL
 649
 650 config ARCH_MX25
 651         bool "NXP MX25"
 652         select CPU_ARM926EJS
 653         imply MXC_GPIO
 654
 655 config ARCH_MX28
 656         bool "NXP i.MX28 family"
 657         select CPU_ARM926EJS
 658         select PL011_SERIAL
 659         select SUPPORT_SPL
 660
 661 config ARCH_MX31
 662         bool "NXP i.MX31 family"
 663         select CPU_ARM1136
 664
 665 config ARCH_MX7ULP
 666         bool "NXP MX7ULP"
 667         select CPU_V7A
 668         select ROM_UNIFIED_SECTIONS
 669         imply MXC_GPIO
 670
 671 config ARCH_MX7
 672         bool "Freescale MX7"
 673         select CPU_V7A
 674         select SYS_FSL_HAS_SEC if SECURE_BOOT
 675         select SYS_FSL_SEC_COMPAT_4
 676         select SYS_FSL_SEC_LE
 677         select BOARD_EARLY_INIT_F
 678         select ARCH_MISC_INIT
 679         imply MXC_GPIO
 680
 681 config ARCH_MX6
 682         bool "Freescale MX6"
 683         select CPU_V7A
 684         select SYS_FSL_HAS_SEC if SECURE_BOOT
 685         select SYS_FSL_SEC_COMPAT_4
 686         select SYS_FSL_SEC_LE
 687         select SYS_THUMB_BUILD if SPL
 688         imply MXC_GPIO
 689
 690 if ARCH_MX6
 691 config SPL_LDSCRIPT
 692         default "arch/arm/mach-omap2/u-boot-spl.lds"
 693 endif
 694
 695 config ARCH_MX5
 696         bool "Freescale MX5"
 697         select CPU_V7A
 698         select BOARD_EARLY_INIT_F
 699         imply MXC_GPIO
 700
 701 config ARCH_QEMU
 702         bool "QEMU Virtual Platform"
 703         select DM
 704         select DM_SERIAL
 705         select OF_CONTROL
 706         select PL01X_SERIAL
 707
 708 config ARCH_RMOBILE
 709         bool "Renesas ARM SoCs"
 710         select DM
 711         select DM_SERIAL
 712         select BOARD_EARLY_INIT_F
 713         imply FAT_WRITE
 714         imply SYS_THUMB_BUILD
 715
 716 config TARGET_S32V234EVB
 717         bool "Support s32v234evb"
 718         select ARM64
 719         select SYS_FSL_ERRATUM_ESDHC111
 720
 721 config ARCH_SNAPDRAGON
 722         bool "Qualcomm Snapdragon SoCs"
 723         select ARM64
 724         select DM
 725         select DM_GPIO
 726         select DM_SERIAL
 727         select SPMI
 728         select OF_CONTROL
 729         select OF_SEPARATE
 730
 731 config ARCH_SOCFPGA
 732         bool "Altera SOCFPGA family"
 733         select ARCH_EARLY_INIT_R
 734         select ARCH_MISC_INIT
 735         select CPU_V7A
 736         select DM
 737         select DM_SERIAL
 738         select ENABLE_ARM_SOC_BOOT0_HOOK
 739         select OF_CONTROL
 740         select SPL_LIBCOMMON_SUPPORT
 741         select SPL_LIBDISK_SUPPORT
 742         select SPL_LIBGENERIC_SUPPORT
 743         select SPL_MMC_SUPPORT if DM_MMC
 744         select SPL_NAND_SUPPORT if SPL_NAND_DENALI
 745         select SPL_OF_CONTROL
 746         select SPL_SERIAL_SUPPORT
 747         select SPL_DM_SERIAL
 748         select SPL_SPI_FLASH_SUPPORT if SPL_SPI_SUPPORT
 749         select SPL_SPI_SUPPORT if DM_SPI
 750         select SPL_WATCHDOG_SUPPORT
 751         select SUPPORT_SPL
 752         select SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
 753         select SYS_NS16550
 754         select SYS_THUMB_BUILD
 755         imply CMD_MTDPARTS
 756         imply CRC32_VERIFY
 757         imply DM_SPI
 758         imply DM_SPI_FLASH
 759         imply FAT_WRITE
 760         imply HW_WATCHDOG
 761         imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
 762
 763 config ARCH_SUNXI
 764         bool "Support sunxi (Allwinner) SoCs"
 765         select BINMAN
 766         select CMD_GPIO
 767         select CMD_MMC if MMC
 768         select CMD_USB if DISTRO_DEFAULTS
 769         select DM
 770         select DM_ETH
 771         select DM_GPIO
 772         select DM_KEYBOARD
 773         select DM_SERIAL
 774         select DM_USB if DISTRO_DEFAULTS
 775         select OF_BOARD_SETUP
 776         select OF_CONTROL
 777         select OF_SEPARATE
 778         select SPECIFY_CONSOLE_INDEX
 779         select SPL_STACK_R if SPL
 780         select SPL_SYS_MALLOC_SIMPLE if SPL
 781         select SYS_NS16550
 782         select SPL_SYS_THUMB_BUILD if !ARM64
 783         select SYS_THUMB_BUILD if !ARM64
 784         select USB if DISTRO_DEFAULTS
 785         select USB_STORAGE if DISTRO_DEFAULTS
 786         select USB_KEYBOARD if DISTRO_DEFAULTS
 787         select USE_TINY_PRINTF
 788         imply CMD_GPT
 789         imply DISTRO_DEFAULTS
 790         imply FAT_WRITE
 791         imply OF_LIBFDT_OVERLAY
 792         imply PRE_CONSOLE_BUFFER
 793         imply SPL_GPIO_SUPPORT
 794         imply SPL_LIBCOMMON_SUPPORT
 795         imply SPL_LIBDISK_SUPPORT
 796         imply SPL_LIBGENERIC_SUPPORT
 797         imply SPL_MMC_SUPPORT if MMC
 798         imply SPL_POWER_SUPPORT
 799         imply SPL_SERIAL_SUPPORT
 800         imply USB_GADGET
 801
 802 config ARCH_VF610
 803         bool "Freescale Vybrid"
 804         select CPU_V7A
 805         select SYS_FSL_ERRATUM_ESDHC111
 806         imply CMD_MTDPARTS
 807         imply NAND
 808
 809 config ARCH_ZYNQ
 810         bool "Xilinx Zynq based platform"
 811         select BOARD_LATE_INIT
 812         select CPU_V7A
 813         select SUPPORT_SPL
 814         select OF_CONTROL
 815         select SPL_BOARD_INIT if SPL
 816         select BOARD_EARLY_INIT_F if WDT
 817         select SPL_OF_CONTROL if SPL
 818         select DM
 819         select DM_ETH if NET
 820         select SPL_DM if SPL
 821         select DM_MMC if MMC
 822         select DM_SPI
 823         select DM_SERIAL
 824         select DM_SPI_FLASH
 825         select SPL_SEPARATE_BSS if SPL
 826         select DM_USB if USB
 827         select CLK
 828         select SPL_CLK if SPL
 829         select CLK_ZYNQ
 830         select SPI
 831         imply CMD_CLK
 832         imply FAT_WRITE
 833         imply CMD_SPL
 834         imply ARCH_EARLY_INIT_R
 835
 836 config ARCH_ZYNQMP_R5
 837         bool "Xilinx ZynqMP R5 based platform"
 838         select CPU_V7R
 839         select OF_CONTROL
 840         select DM
 841         select DM_SERIAL
 842         select CLK
 843
 844 config ARCH_ZYNQMP
 845         bool "Xilinx ZynqMP based platform"
 846         select ARM64
 847         select BOARD_LATE_INIT
 848         select DM
 849         select OF_CONTROL
 850         select DM_SERIAL
 851         select SUPPORT_SPL
 852         select CLK
 853         select SPL_BOARD_INIT if SPL
 854         select SPL_CLK if SPL
 855         select DM_USB if USB
 856         imply FAT_WRITE
 857
 858 config TEGRA
 859         bool "NVIDIA Tegra"
 860         imply DISTRO_DEFAULTS
 861         imply FAT_WRITE
 862
 863 config TARGET_VEXPRESS64_AEMV8A
 864         bool "Support vexpress_aemv8a"
 865         select ARM64
 866         select PL01X_SERIAL
 867
 868 config TARGET_VEXPRESS64_BASE_FVP
 869         bool "Support Versatile Express ARMv8a FVP BASE model"
 870         select ARM64
 871         select SEMIHOSTING
 872         select PL01X_SERIAL
 873
 874 config TARGET_VEXPRESS64_BASE_FVP_DRAM
 875         bool "Support Versatile Express ARMv8a FVP BASE model booting from DRAM"
 876         select ARM64
 877         select PL01X_SERIAL
 878         help
 879           This target is derived from TARGET_VEXPRESS64_BASE_FVP and over-rides
 880           the default config to allow the user to load the images directly into
 881           DRAM using model parameters rather than by using semi-hosting to load
 882           the files from the host filesystem.
 883
 884 config TARGET_VEXPRESS64_JUNO
 885         bool "Support Versatile Express Juno Development Platform"
 886         select ARM64
 887         select PL01X_SERIAL
 888
 889 config TARGET_LS2080A_EMU
 890         bool "Support ls2080a_emu"
 891         select ARCH_LS2080A
 892         select ARM64
 893         select ARMV8_MULTIENTRY
 894         select ARCH_MISC_INIT
 895         help
 896           Support for Freescale LS2080A_EMU platform
 897           The LS2080A Development System (EMULATOR) is a pre silicon
 898           development platform that supports the QorIQ LS2080A
 899           Layerscape Architecture processor.
 900
 901 config TARGET_LS2080A_SIMU
 902         bool "Support ls2080a_simu"
 903         select ARCH_LS2080A
 904         select ARM64
 905         select ARMV8_MULTIENTRY
 906         select ARCH_MISC_INIT
 907         help
 908           Support for Freescale LS2080A_SIMU platform
 909           The LS2080A Development System (QDS) is a pre silicon
 910           development platform that supports the QorIQ LS2080A
 911           Layerscape Architecture processor.
 912
 913 config TARGET_LS1088AQDS
 914         bool "Support ls1088aqds"
 915         select ARCH_LS1088A
 916         select ARM64
 917         select ARMV8_MULTIENTRY
 918         select ARCH_MISC_INIT
 919         select BOARD_LATE_INIT
 920         select SUPPORT_SPL
 921         help
 922           Support for NXP LS1088AQDS platform
 923           The LS1088A Development System (QDS) is a high-performance
 924           development platform that supports the QorIQ LS1088A
 925           Layerscape Architecture processor.
 926
 927 config TARGET_LS2080AQDS
 928         bool "Support ls2080aqds"
 929         select ARCH_LS2080A
 930         select ARM64
 931         select ARMV8_MULTIENTRY
 932         select BOARD_LATE_INIT
 933         select SUPPORT_SPL
 934         select ARCH_MISC_INIT
 935         imply SCSI
 936         imply SCSI_AHCI
 937         help
 938           Support for Freescale LS2080AQDS platform
 939           The LS2080A Development System (QDS) is a high-performance
 940           development platform that supports the QorIQ LS2080A
 941           Layerscape Architecture processor.
 942
 943 config TARGET_LS2080ARDB
 944         bool "Support ls2080ardb"
 945         select ARCH_LS2080A
 946         select ARM64
 947         select ARMV8_MULTIENTRY
 948         select BOARD_LATE_INIT
 949         select SUPPORT_SPL
 950         select ARCH_MISC_INIT
 951         imply SCSI
 952         imply SCSI_AHCI
 953         help
 954           Support for Freescale LS2080ARDB platform.
 955           The LS2080A Reference design board (RDB) is a high-performance
 956           development platform that supports the QorIQ LS2080A
 957           Layerscape Architecture processor.
 958
 959 config TARGET_LS2081ARDB
 960         bool "Support ls2081ardb"
 961         select ARCH_LS2080A
 962         select ARM64
 963         select ARMV8_MULTIENTRY
 964         select BOARD_LATE_INIT
 965         select SUPPORT_SPL
 966         select ARCH_MISC_INIT
 967         help
 968           Support for Freescale LS2081ARDB platform.
 969           The LS2081A Reference design board (RDB) is a high-performance
 970           development platform that supports the QorIQ LS2081A/LS2041A
 971           Layerscape Architecture processor.
 972
 973 config TARGET_HIKEY
 974         bool "Support HiKey 96boards Consumer Edition Platform"
 975         select ARM64
 976         select DM
 977         select DM_GPIO
 978         select DM_SERIAL
 979         select OF_CONTROL
 980         select PL01X_SERIAL
 981         select SPECIFY_CONSOLE_INDEX
 982           help
 983           Support for HiKey 96boards platform. It features a HI6220
 984           SoC, with 8xA53 CPU, mali450 gpu, and 1GB RAM.
 985
 986 config TARGET_POPLAR
 987         bool "Support Poplar 96boards Enterprise Edition Platform"
 988         select ARM64
 989         select DM
 990         select OF_CONTROL
 991         select DM_SERIAL
 992         select DM_USB
 993         select PL01X_SERIAL
 994           help
 995           Support for Poplar 96boards EE platform. It features a HI3798cv200
 996           SoC, with 4xA53 CPU, 1GB RAM and the high performance Mali T720 GPU
 997           making it capable of running any commercial set-top solution based on
 998           Linux or Android.
 999
1000 config TARGET_LS1012AQDS
1001         bool "Support ls1012aqds"
1002         select ARCH_LS1012A
1003         select ARM64
1004         select BOARD_LATE_INIT
1005         help
1006           Support for Freescale LS1012AQDS platform.
1007           The LS1012A Development System (QDS) is a high-performance
1008           development platform that supports the QorIQ LS1012A
1009           Layerscape Architecture processor.
1010
1011 config TARGET_LS1012ARDB
1012         bool "Support ls1012ardb"
1013         select ARCH_LS1012A
1014         select ARM64
1015         select BOARD_LATE_INIT
1016         imply SCSI
1017         imply SCSI_AHCI
1018         help
1019           Support for Freescale LS1012ARDB platform.
1020           The LS1012A Reference design board (RDB) is a high-performance
1021           development platform that supports the QorIQ LS1012A
1022           Layerscape Architecture processor.
1023
1024 config TARGET_LS1012A2G5RDB
1025         bool "Support ls1012a2g5rdb"
1026         select ARCH_LS1012A
1027         select ARM64
1028         select BOARD_LATE_INIT
1029         imply SCSI
1030         help
1031           Support for Freescale LS1012A2G5RDB platform.
1032           The LS1012A 2G5 Reference design board (RDB) is a high-performance
1033           development platform that supports the QorIQ LS1012A
1034           Layerscape Architecture processor.
1035
1036 config TARGET_LS1012AFRDM
1037         bool "Support ls1012afrdm"
1038         select ARCH_LS1012A
1039         select ARM64
1040         help
1041           Support for Freescale LS1012AFRDM platform.
1042           The LS1012A Freedom  board (FRDM) is a high-performance
1043           development platform that supports the QorIQ LS1012A
1044           Layerscape Architecture processor.
1045
1046 config TARGET_LS1088ARDB
1047         bool "Support ls1088ardb"
1048         select ARCH_LS1088A
1049         select ARM64
1050         select ARMV8_MULTIENTRY
1051         select ARCH_MISC_INIT
1052         select BOARD_LATE_INIT
1053         select SUPPORT_SPL
1054         help
1055           Support for NXP LS1088ARDB platform.
1056           The LS1088A Reference design board (RDB) is a high-performance
1057           development platform that supports the QorIQ LS1088A
1058           Layerscape Architecture processor.
1059
1060 config TARGET_LS1021AQDS
1061         bool "Support ls1021aqds"
1062         select BOARD_LATE_INIT
1063         select CPU_V7A
1064         select CPU_V7_HAS_NONSEC
1065         select CPU_V7_HAS_VIRT
1066         select SUPPORT_SPL
1067         select ARCH_LS1021A
1068         select ARCH_SUPPORT_PSCI
1069         select LS1_DEEP_SLEEP
1070         select SYS_FSL_DDR
1071         select BOARD_EARLY_INIT_F
1072         imply SCSI
1073
1074 config TARGET_LS1021ATWR
1075         bool "Support ls1021atwr"
1076         select BOARD_LATE_INIT
1077         select CPU_V7A
1078         select CPU_V7_HAS_NONSEC
1079         select CPU_V7_HAS_VIRT
1080         select SUPPORT_SPL
1081         select ARCH_LS1021A
1082         select ARCH_SUPPORT_PSCI
1083         select LS1_DEEP_SLEEP
1084         select BOARD_EARLY_INIT_F
1085         imply SCSI
1086
1087 config TARGET_LS1021AIOT
1088         bool "Support ls1021aiot"
1089         select BOARD_LATE_INIT
1090         select CPU_V7A
1091         select CPU_V7_HAS_NONSEC
1092         select CPU_V7_HAS_VIRT
1093         select SUPPORT_SPL
1094         select ARCH_LS1021A
1095         select ARCH_SUPPORT_PSCI
1096         imply SCSI
1097         help
1098           Support for Freescale LS1021AIOT platform.
1099           The LS1021A Freescale board (IOT) is a high-performance
1100           development platform that supports the QorIQ LS1021A
1101           Layerscape Architecture processor.
1102
1103 config TARGET_LS1043AQDS
1104         bool "Support ls1043aqds"
1105         select ARCH_LS1043A
1106         select ARM64
1107         select ARMV8_MULTIENTRY
1108         select BOARD_LATE_INIT
1109         select SUPPORT_SPL
1110         select BOARD_EARLY_INIT_F
1111         imply SCSI
1112         help
1113           Support for Freescale LS1043AQDS platform.
1114
1115 config TARGET_LS1043ARDB
1116         bool "Support ls1043ardb"
1117         select ARCH_LS1043A
1118         select ARM64
1119         select ARMV8_MULTIENTRY
1120         select BOARD_LATE_INIT
1121         select SUPPORT_SPL
1122         select BOARD_EARLY_INIT_F
1123         imply SCSI
1124         help
1125           Support for Freescale LS1043ARDB platform.
1126
1127 config TARGET_LS1046AQDS
1128         bool "Support ls1046aqds"
1129         select ARCH_LS1046A
1130         select ARM64
1131         select ARMV8_MULTIENTRY
1132         select BOARD_LATE_INIT
1133         select SUPPORT_SPL
1134         select DM_SPI_FLASH if DM_SPI
1135         select BOARD_EARLY_INIT_F
1136         imply SCSI
1137         help
1138           Support for Freescale LS1046AQDS platform.
1139           The LS1046A Development System (QDS) is a high-performance
1140           development platform that supports the QorIQ LS1046A
1141           Layerscape Architecture processor.
1142
1143 config TARGET_LS1046ARDB
1144         bool "Support ls1046ardb"
1145         select ARCH_LS1046A
1146         select ARM64
1147         select ARMV8_MULTIENTRY
1148         select BOARD_LATE_INIT
1149         select SUPPORT_SPL
1150         select DM_SPI_FLASH if DM_SPI
1151         select POWER_MC34VR500
1152         select BOARD_EARLY_INIT_F
1153         imply SCSI
1154         help
1155           Support for Freescale LS1046ARDB platform.
1156           The LS1046A Reference Design Board (RDB) is a high-performance
1157           development platform that supports the QorIQ LS1046A
1158           Layerscape Architecture processor.
1159
1160 config TARGET_H2200
1161         bool "Support h2200"
1162         select CPU_PXA
1163
1164 config TARGET_ZIPITZ2
1165         bool "Support zipitz2"
1166         select CPU_PXA
1167
1168 config TARGET_COLIBRI_PXA270
1169         bool "Support colibri_pxa270"
1170         select CPU_PXA
1171
1172 config ARCH_UNIPHIER
1173         bool "Socionext UniPhier SoCs"
1174         select BOARD_LATE_INIT
1175         select DM
1176         select DM_GPIO
1177         select DM_I2C
1178         select DM_MMC
1179         select DM_RESET
1180         select DM_SERIAL
1181         select DM_USB
1182         select OF_CONTROL
1183         select OF_LIBFDT
1184         select PINCTRL
1185         select SPL_BOARD_INIT if SPL
1186         select SPL_DM if SPL
1187         select SPL_LIBCOMMON_SUPPORT if SPL
1188         select SPL_LIBGENERIC_SUPPORT if SPL
1189         select SPL_OF_CONTROL if SPL
1190         select SPL_PINCTRL if SPL
1191         select SUPPORT_SPL
1192         imply FAT_WRITE
1193         help
1194           Support for UniPhier SoC family developed by Socionext Inc.
1195           (formerly, System LSI Business Division of Panasonic Corporation)
1196
1197 config STM32
1198         bool "Support STMicroelectronics STM32 MCU with cortex M"
1199         select CPU_V7M
1200         select DM
1201         select DM_SERIAL
1202         select SYS_THUMB_BUILD
1203
1204 config ARCH_STI
1205         bool "Support STMicrolectronics SoCs"
1206         select CPU_V7A
1207         select DM
1208         select DM_SERIAL
1209         select BLK
1210         select DM_MMC
1211         select DM_RESET
1212         help
1213           Support for STMicroelectronics STiH407/10 SoC family.
1214           This SoC is used on Linaro 96Board STiH410-B2260
1215
1216 config ARCH_STM32MP
1217         bool "Support STMicroelectronics STM32MP Socs with cortex A"
1218         select ARCH_MISC_INIT
1219         select BOARD_LATE_INIT
1220         select CLK
1221         select DM
1222         select DM_GPIO
1223         select DM_RESET
1224         select DM_SERIAL
1225         select OF_CONTROL
1226         select OF_LIBFDT
1227         select PINCTRL
1228         select REGMAP
1229         select SUPPORT_SPL
1230         select SYSCON
1231         select SYSRESET
1232         select SYS_THUMB_BUILD
1233         help
1234           Support for STM32MP SoC family developed by STMicroelectronics,
1235           MPUs based on ARM cortex A core
1236           U-BOOT is running in DDR and SPL support is the unsecure First Stage
1237           BootLoader (FSBL)
1238
1239 config ARCH_ROCKCHIP
1240         bool "Support Rockchip SoCs"
1241         select OF_CONTROL
1242         select BLK
1243         select DM
1244         select SPL_DM if SPL
1245         select SYS_MALLOC_F
1246         select SYS_THUMB_BUILD if !ARM64
1247         select SPL_SYS_MALLOC_SIMPLE if SPL
1248         select DM_GPIO
1249         select DM_I2C
1250         select DM_MMC
1251         select DM_SERIAL
1252         select DM_SPI
1253         select DM_SPI_FLASH
1254         select DM_USB if USB
1255         select DM_PWM
1256         select DM_REGULATOR
1257         select ENABLE_ARM_SOC_BOOT0_HOOK
1258         select SPI
1259         imply CMD_FASTBOOT
1260         imply DISTRO_DEFAULTS
1261         imply FASTBOOT
1262         imply FAT_WRITE
1263         imply USB_FUNCTION_FASTBOOT
1264         imply SPL_SYSRESET
1265         imply TPL_SYSRESET
1266         imply ADC
1267         imply SARADC_ROCKCHIP
1268         imply SYS_NS16550
1269
1270 config TARGET_THUNDERX_88XX
1271         bool "Support ThunderX 88xx"
1272         select ARM64
1273         select OF_CONTROL
1274         select SYS_CACHE_SHIFT_7
1275         select PL01X_SERIAL
1276
1277 config ARCH_ASPEED
1278         bool "Support Aspeed SoCs"
1279         select OF_CONTROL
1280         select DM
1281
1282 endchoice
1283
1284 config TI_SECURE_DEVICE
1285         bool "HS Device Type Support"
1286         depends on ARCH_KEYSTONE || ARCH_OMAP2PLUS
1287         help
1288           If a high secure (HS) device type is being used, this config
1289           must be set. This option impacts various aspects of the
1290           build system (to create signed boot images that can be
1291           authenticated) and the code. See the doc/README.ti-secure
1292           file for further details.
1293
1294 source "arch/arm/mach-aspeed/Kconfig"
1295
1296 source "arch/arm/mach-at91/Kconfig"
1297
1298 source "arch/arm/mach-bcm283x/Kconfig"
1299
1300 source "arch/arm/mach-davinci/Kconfig"
1301
1302 source "arch/arm/mach-exynos/Kconfig"
1303
1304 source "arch/arm/mach-highbank/Kconfig"
1305
1306 source "arch/arm/mach-integrator/Kconfig"
1307
1308 source "arch/arm/mach-keystone/Kconfig"
1309
1310 source "arch/arm/mach-kirkwood/Kconfig"
1311
1312 source "arch/arm/mach-mvebu/Kconfig"
1313
1314 source "arch/arm/cpu/armv7/ls102xa/Kconfig"
1315
1316 source "arch/arm/mach-imx/mx2/Kconfig"
1317
1318 source "arch/arm/mach-imx/mx3/Kconfig"
1319
1320 source "arch/arm/mach-imx/mx5/Kconfig"
1321
1322 source "arch/arm/mach-imx/mx6/Kconfig"
1323
1324 source "arch/arm/mach-imx/mx7/Kconfig"
1325
1326 source "arch/arm/mach-imx/mx7ulp/Kconfig"
1327
1328 source "arch/arm/mach-imx/mx8m/Kconfig"
1329
1330 source "arch/arm/mach-imx/mxs/Kconfig"
1331
1332 source "arch/arm/mach-omap2/Kconfig"
1333
1334 source "arch/arm/cpu/armv8/fsl-layerscape/Kconfig"
1335
1336 source "arch/arm/mach-orion5x/Kconfig"
1337
1338 source "arch/arm/mach-rmobile/Kconfig"
1339
1340 source "arch/arm/mach-meson/Kconfig"
1341
1342 source "arch/arm/mach-qemu/Kconfig"
1343
1344 source "arch/arm/mach-rockchip/Kconfig"
1345
1346 source "arch/arm/mach-s5pc1xx/Kconfig"
1347
1348 source "arch/arm/mach-snapdragon/Kconfig"
1349
1350 source "arch/arm/mach-socfpga/Kconfig"
1351
1352 source "arch/arm/mach-sti/Kconfig"
1353
1354 source "arch/arm/mach-stm32/Kconfig"
1355
1356 source "arch/arm/mach-stm32mp/Kconfig"
1357
1358 source "arch/arm/mach-sunxi/Kconfig"
1359
1360 source "arch/arm/mach-tegra/Kconfig"
1361
1362 source "arch/arm/mach-uniphier/Kconfig"
1363
1364 source "arch/arm/cpu/armv7/vf610/Kconfig"
1365
1366 source "arch/arm/mach-zynq/Kconfig"
1367
1368 source "arch/arm/mach-zynqmp-r5/Kconfig"
1369
1370 source "arch/arm/cpu/armv7/Kconfig"
1371
1372 source "arch/arm/cpu/armv8/zynqmp/Kconfig"
1373
1374 source "arch/arm/cpu/armv8/Kconfig"
1375
1376 source "arch/arm/mach-imx/Kconfig"
1377
1378 source "board/bosch/shc/Kconfig"
1379 source "board/CarMediaLab/flea3/Kconfig"
1380 source "board/Marvell/aspenite/Kconfig"
1381 source "board/Marvell/gplugd/Kconfig"
1382 source "board/armadeus/apf27/Kconfig"
1383 source "board/armltd/vexpress/Kconfig"
1384 source "board/armltd/vexpress64/Kconfig"
1385 source "board/broadcom/bcm23550_w1d/Kconfig"
1386 source "board/broadcom/bcm28155_ap/Kconfig"
1387 source "board/broadcom/bcmcygnus/Kconfig"
1388 source "board/broadcom/bcmnsp/Kconfig"
1389 source "board/broadcom/bcmns2/Kconfig"
1390 source "board/cavium/thunderx/Kconfig"
1391 source "board/cirrus/edb93xx/Kconfig"
1392 source "board/eets/pdu001/Kconfig"
1393 source "board/freescale/ls2080a/Kconfig"
1394 source "board/freescale/ls2080aqds/Kconfig"
1395 source "board/freescale/ls2080ardb/Kconfig"
1396 source "board/freescale/ls1088a/Kconfig"
1397 source "board/freescale/ls1021aqds/Kconfig"
1398 source "board/freescale/ls1043aqds/Kconfig"
1399 source "board/freescale/ls1021atwr/Kconfig"
1400 source "board/freescale/ls1021aiot/Kconfig"
1401 source "board/freescale/ls1046aqds/Kconfig"
1402 source "board/freescale/ls1043ardb/Kconfig"
1403 source "board/freescale/ls1046ardb/Kconfig"
1404 source "board/freescale/ls1012aqds/Kconfig"
1405 source "board/freescale/ls1012ardb/Kconfig"
1406 source "board/freescale/ls1012afrdm/Kconfig"
1407 source "board/freescale/mx35pdk/Kconfig"
1408 source "board/freescale/s32v234evb/Kconfig"
1409 source "board/gdsys/a38x/Kconfig"
1410 source "board/grinn/chiliboard/Kconfig"
1411 source "board/gumstix/pepper/Kconfig"
1412 source "board/h2200/Kconfig"
1413 source "board/hisilicon/hikey/Kconfig"
1414 source "board/hisilicon/poplar/Kconfig"
1415 source "board/isee/igep003x/Kconfig"
1416 source "board/phytec/pcm051/Kconfig"
1417 source "board/silica/pengwyn/Kconfig"
1418 source "board/spear/spear300/Kconfig"
1419 source "board/spear/spear310/Kconfig"
1420 source "board/spear/spear320/Kconfig"
1421 source "board/spear/spear600/Kconfig"
1422 source "board/spear/x600/Kconfig"
1423 source "board/st/stv0991/Kconfig"
1424 source "board/tcl/sl50/Kconfig"
1425 source "board/birdland/bav335x/Kconfig"
1426 source "board/timll/devkit3250/Kconfig"
1427 source "board/toradex/colibri_pxa270/Kconfig"
1428 source "board/vscom/baltos/Kconfig"
1429 source "board/woodburn/Kconfig"
1430 source "board/work-microwave/work_92105/Kconfig"
1431 source "board/xilinx/zynqmp/Kconfig"
1432 source "board/zipitz2/Kconfig"
1433
1434 source "arch/arm/Kconfig.debug"
1435
1436 endmenu
1437
1438 config SPL_LDSCRIPT
1439         default "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" if (ARCH_MX23 || ARCH_MX28) && !SPL_FRAMEWORK
1440         default "arch/arm/cpu/arm1136/u-boot-spl.lds" if CPU_ARM1136
1441         default "arch/arm/cpu/armv8/u-boot-spl.lds" if ARM64
1442
1443