arch/arm/Kconfig

   1 menu "ARM architecture"
   2         depends on ARM
   3
   4 config SYS_ARCH
   5         default "arm"
   6
   7 config ARM64
   8         bool
   9         select PHYS_64BIT
  10         select SYS_CACHE_SHIFT_6
  11
  12 if ARM64
  13 config POSITION_INDEPENDENT
  14         bool "Generate position-independent pre-relocation code"
  15         help
  16           U-Boot expects to be linked to a specific hard-coded address, and to
  17           be loaded to and run from that address. This option lifts that
  18           restriction, thus allowing the code to be loaded to and executed
  19           from almost any address. This logic relies on the relocation
  20           information that is embedded into the binary to support U-Boot
  21           relocating itself to the top-of-RAM later during execution.
  22
  23 config SYS_INIT_SP_BSS_OFFSET
  24         int
  25         help
  26           U-Boot typically uses a hard-coded value for the stack pointer
  27           before relocation. Define this option to instead calculate the
  28           initial SP at run-time. This is useful to avoid hard-coding addresses
  29           into U-Boot, so that can be loaded and executed at arbitrary
  30           addresses and thus avoid using arbitrary addresses at runtime. This
  31           option's value is the offset added to &_bss_start in order to
  32           calculate the stack pointer. This offset should be large enough so
  33           that the early malloc region, global data (gd), and early stack usage
  34           do not overlap any appended DTB.
  35
  36 config LINUX_KERNEL_IMAGE_HEADER
  37         bool
  38         help
  39           Place a Linux kernel image header at the start of the U-Boot binary.
  40           The format of the header is described in the Linux kernel source at
  41           Documentation/arm64/booting.txt. This feature is useful since the
  42           image header reports the amount of memory (BSS and similar) that
  43           U-Boot needs to use, but which isn't part of the binary.
  44
  45 if LINUX_KERNEL_IMAGE_HEADER
  46 config LNX_KRNL_IMG_TEXT_OFFSET_BASE
  47         hex
  48         help
  49           The value subtracted from CONFIG_SYS_TEXT_BASE to calculate the
  50           TEXT_OFFSET value written in to the Linux kernel image header.
  51 endif
  52 endif
  53
  54 config STATIC_RELA
  55         bool
  56         default y if ARM64 && !POSITION_INDEPENDENT
  57
  58 config DMA_ADDR_T_64BIT
  59         bool
  60         default y if ARM64
  61
  62 config HAS_VBAR
  63         bool
  64
  65 config HAS_THUMB2
  66         bool
  67
  68 # Used for compatibility with asm files copied from the kernel
  69 config ARM_ASM_UNIFIED
  70         bool
  71         default y
  72
  73 # Used for compatibility with asm files copied from the kernel
  74 config THUMB2_KERNEL
  75         bool
  76
  77 config SYS_ARM_CACHE_CP15
  78         bool "CP15 based cache enabling support"
  79         help
  80           Select this if your processor suports enabling caches by using
  81           CP15 registers.
  82
  83 config SYS_ARM_MMU
  84         bool "MMU-based Paged Memory Management Support"
  85         select SYS_ARM_CACHE_CP15
  86         help
  87           Select if you want MMU-based virtualised addressing space
  88           support by paged memory management.
  89
  90 config SYS_ARM_MPU
  91         bool 'Use the ARM v7 PMSA Compliant MPU'
  92         help
  93           Some ARM systems without an MMU have instead a Memory Protection
  94           Unit (MPU) that defines the type and permissions for regions of
  95           memory.
  96           If your CPU has an MPU then you should choose 'y' here unless you
  97           know that you do not want to use the MPU.
  98
  99 # If set, the workarounds for these ARM errata are applied early during U-Boot
 100 # startup. Note that in general these options force the workarounds to be
 101 # applied; no CPU-type/version detection exists, unlike the similar options in
 102 # the Linux kernel. Do not set these options unless they apply!  Also note that
 103 # the following can be machine specific errata. These do have ability to
 104 # provide rudimentary version and machine specific checks, but expect no
 105 # product checks:
 106 # CONFIG_ARM_ERRATA_430973
 107 # CONFIG_ARM_ERRATA_454179
 108 # CONFIG_ARM_ERRATA_621766
 109 # CONFIG_ARM_ERRATA_798870
 110 # CONFIG_ARM_ERRATA_801819
 111 # CONFIG_ARM_CORTEX_A8_CVE_2017_5715
 112 # CONFIG_ARM_CORTEX_A15_CVE_2017_5715
 113
 114 config ARM_ERRATA_430973
 115         bool
 116
 117 config ARM_ERRATA_454179
 118         bool
 119
 120 config ARM_ERRATA_621766
 121         bool
 122
 123 config ARM_ERRATA_716044
 124         bool
 125
 126 config ARM_ERRATA_725233
 127         bool
 128
 129 config ARM_ERRATA_742230
 130         bool
 131
 132 config ARM_ERRATA_743622
 133         bool
 134
 135 config ARM_ERRATA_751472
 136         bool
 137
 138 config ARM_ERRATA_761320
 139         bool
 140
 141 config ARM_ERRATA_773022
 142         bool
 143
 144 config ARM_ERRATA_774769
 145         bool
 146
 147 config ARM_ERRATA_794072
 148         bool
 149
 150 config ARM_ERRATA_798870
 151         bool
 152
 153 config ARM_ERRATA_801819
 154         bool
 155
 156 config ARM_ERRATA_826974
 157         bool
 158
 159 config ARM_ERRATA_828024
 160         bool
 161
 162 config ARM_ERRATA_829520
 163         bool
 164
 165 config ARM_ERRATA_833069
 166         bool
 167
 168 config ARM_ERRATA_833471
 169         bool
 170
 171 config ARM_ERRATA_845369
 172         bool
 173
 174 config ARM_ERRATA_852421
 175         bool
 176
 177 config ARM_ERRATA_852423
 178         bool
 179
 180 config ARM_ERRATA_855873
 181         bool
 182
 183 config ARM_CORTEX_A8_CVE_2017_5715
 184         bool
 185
 186 config ARM_CORTEX_A15_CVE_2017_5715
 187         bool
 188
 189 config CPU_ARM720T
 190         bool
 191         select SYS_CACHE_SHIFT_5
 192         imply SYS_ARM_MMU
 193
 194 config CPU_ARM920T
 195         bool
 196         select SYS_CACHE_SHIFT_5
 197         imply SYS_ARM_MMU
 198
 199 config CPU_ARM926EJS
 200         bool
 201         select SYS_CACHE_SHIFT_5
 202         imply SYS_ARM_MMU
 203
 204 config CPU_ARM946ES
 205         bool
 206         select SYS_CACHE_SHIFT_5
 207         imply SYS_ARM_MMU
 208
 209 config CPU_ARM1136
 210         bool
 211         select SYS_CACHE_SHIFT_5
 212         imply SYS_ARM_MMU
 213
 214 config CPU_ARM1176
 215         bool
 216         select HAS_VBAR
 217         select SYS_CACHE_SHIFT_5
 218         imply SYS_ARM_MMU
 219
 220 config CPU_V7A
 221         bool
 222         select HAS_THUMB2
 223         select HAS_VBAR
 224         select SYS_CACHE_SHIFT_6
 225         imply SYS_ARM_MMU
 226
 227 config CPU_V7M
 228         bool
 229         select HAS_THUMB2
 230         select SYS_ARM_MPU
 231         select SYS_CACHE_SHIFT_5
 232         select SYS_THUMB_BUILD
 233         select THUMB2_KERNEL
 234
 235 config CPU_V7R
 236         bool
 237         select HAS_THUMB2
 238         select SYS_ARM_CACHE_CP15
 239         select SYS_ARM_MPU
 240         select SYS_CACHE_SHIFT_6
 241
 242 config CPU_PXA
 243         bool
 244         select SYS_CACHE_SHIFT_5
 245         imply SYS_ARM_MMU
 246
 247 config CPU_SA1100
 248         bool
 249         select SYS_CACHE_SHIFT_5
 250         imply SYS_ARM_MMU
 251
 252 config SYS_CPU
 253         default "arm720t" if CPU_ARM720T
 254         default "arm920t" if CPU_ARM920T
 255         default "arm926ejs" if CPU_ARM926EJS
 256         default "arm946es" if CPU_ARM946ES
 257         default "arm1136" if CPU_ARM1136
 258         default "arm1176" if CPU_ARM1176
 259         default "armv7" if CPU_V7A
 260         default "armv7" if CPU_V7R
 261         default "armv7m" if CPU_V7M
 262         default "pxa" if CPU_PXA
 263         default "sa1100" if CPU_SA1100
 264         default "armv8" if ARM64
 265
 266 config SYS_ARM_ARCH
 267         int
 268         default 4 if CPU_ARM720T
 269         default 4 if CPU_ARM920T
 270         default 5 if CPU_ARM926EJS
 271         default 5 if CPU_ARM946ES
 272         default 6 if CPU_ARM1136
 273         default 6 if CPU_ARM1176
 274         default 7 if CPU_V7A
 275         default 7 if CPU_V7M
 276         default 7 if CPU_V7R
 277         default 5 if CPU_PXA
 278         default 4 if CPU_SA1100
 279         default 8 if ARM64
 280
 281 config SYS_CACHE_SHIFT_5
 282         bool
 283
 284 config SYS_CACHE_SHIFT_6
 285         bool
 286
 287 config SYS_CACHE_SHIFT_7
 288         bool
 289
 290 config SYS_CACHELINE_SIZE
 291         int
 292         default 128 if SYS_CACHE_SHIFT_7
 293         default 64 if SYS_CACHE_SHIFT_6
 294         default 32 if SYS_CACHE_SHIFT_5
 295
 296 config SYS_ARCH_TIMER
 297         bool "ARM Generic Timer support"
 298         depends on CPU_V7A || ARM64
 299         default y if ARM64
 300         help
 301           The ARM Generic Timer (aka arch-timer) provides an architected
 302           interface to a timer source on an SoC.
 303           It is mandantory for ARMv8 implementation and widely available
 304           on ARMv7 systems.
 305
 306 config ARM_SMCCC
 307         bool "Support for ARM SMC Calling Convention (SMCCC)"
 308         depends on CPU_V7A || ARM64
 309         select ARM_PSCI_FW
 310         help
 311           Say Y here if you want to enable ARM SMC Calling Convention.
 312           This should be enabled if U-Boot needs to communicate with system
 313           firmware (for example, PSCI) according to SMCCC.
 314
 315 config SEMIHOSTING
 316         bool "support boot from semihosting"
 317         help
 318           In emulated environments, semihosting is a way for
 319           the hosted environment to call out to the emulator to
 320           retrieve files from the host machine.
 321
 322 config SYS_THUMB_BUILD
 323         bool "Build U-Boot using the Thumb instruction set"
 324         depends on !ARM64
 325         help
 326            Use this flag to build U-Boot using the Thumb instruction set for
 327            ARM architectures. Thumb instruction set provides better code
 328            density. For ARM architectures that support Thumb2 this flag will
 329            result in Thumb2 code generated by GCC.
 330
 331 config SPL_SYS_THUMB_BUILD
 332         bool "Build SPL using the Thumb instruction set"
 333         default y if SYS_THUMB_BUILD
 334         depends on !ARM64
 335         help
 336            Use this flag to build SPL using the Thumb instruction set for
 337            ARM architectures. Thumb instruction set provides better code
 338            density. For ARM architectures that support Thumb2 this flag will
 339            result in Thumb2 code generated by GCC.
 340
 341 config SYS_L2CACHE_OFF
 342         bool "L2cache off"
 343         help
 344           If SoC does not support L2CACHE or one do not want to enable
 345           L2CACHE, choose this option.
 346
 347 config ENABLE_ARM_SOC_BOOT0_HOOK
 348         bool "prepare BOOT0 header"
 349         help
 350           If the SoC's BOOT0 requires a header area filled with (magic)
 351           values, then choose this option, and create a file included as
 352           <asm/arch/boot0.h> which contains the required assembler code.
 353
 354 config ARM_CORTEX_CPU_IS_UP
 355         bool
 356         default n
 357
 358 config USE_ARCH_MEMCPY
 359         bool "Use an assembly optimized implementation of memcpy"
 360         default y
 361         depends on !ARM64
 362         help
 363           Enable the generation of an optimized version of memcpy.
 364           Such implementation may be faster under some conditions
 365           but may increase the binary size.
 366
 367 config SPL_USE_ARCH_MEMCPY
 368         bool "Use an assembly optimized implementation of memcpy for SPL"
 369         default y if USE_ARCH_MEMCPY
 370         depends on !ARM64
 371         help
 372           Enable the generation of an optimized version of memcpy.
 373           Such implementation may be faster under some conditions
 374           but may increase the binary size.
 375
 376 config USE_ARCH_MEMSET
 377         bool "Use an assembly optimized implementation of memset"
 378         default y
 379         depends on !ARM64
 380         help
 381           Enable the generation of an optimized version of memset.
 382           Such implementation may be faster under some conditions
 383           but may increase the binary size.
 384
 385 config SPL_USE_ARCH_MEMSET
 386         bool "Use an assembly optimized implementation of memset for SPL"
 387         default y if USE_ARCH_MEMSET
 388         depends on !ARM64
 389         help
 390           Enable the generation of an optimized version of memset.
 391           Such implementation may be faster under some conditions
 392           but may increase the binary size.
 393
 394 config ARM64_SUPPORT_AARCH32
 395         bool "ARM64 system support AArch32 execution state"
 396         default y if ARM64 && !TARGET_THUNDERX_88XX
 397         help
 398           This ARM64 system supports AArch32 execution state.
 399
 400 choice
 401         prompt "Target select"
 402         default TARGET_HIKEY
 403
 404 config ARCH_AT91
 405         bool "Atmel AT91"
 406         select SPL_BOARD_INIT if SPL && !TARGET_SMARTWEB
 407
 408 config TARGET_EDB93XX
 409         bool "Support edb93xx"
 410         select CPU_ARM920T
 411         select PL010_SERIAL
 412
 413 config TARGET_ASPENITE
 414         bool "Support aspenite"
 415         select CPU_ARM926EJS
 416
 417 config TARGET_GPLUGD
 418         bool "Support gplugd"
 419         select CPU_ARM926EJS
 420
 421 config ARCH_DAVINCI
 422         bool "TI DaVinci"
 423         select CPU_ARM926EJS
 424         imply CMD_SAVES
 425         help
 426           Support for TI's DaVinci platform.
 427
 428 config KIRKWOOD
 429         bool "Marvell Kirkwood"
 430         select ARCH_MISC_INIT
 431         select BOARD_EARLY_INIT_F
 432         select CPU_ARM926EJS
 433
 434 config ARCH_MVEBU
 435         bool "Marvell MVEBU family (Armada XP/375/38x/3700/7K/8K)"
 436         select DM
 437         select DM_ETH
 438         select DM_SERIAL
 439         select DM_SPI
 440         select DM_SPI_FLASH
 441         select OF_CONTROL
 442         select OF_SEPARATE
 443         select SPI
 444         imply CMD_DM
 445
 446 config TARGET_DEVKIT3250
 447         bool "Support devkit3250"
 448         select CPU_ARM926EJS
 449         select SUPPORT_SPL
 450
 451 config TARGET_WORK_92105
 452         bool "Support work_92105"
 453         select CPU_ARM926EJS
 454         select SUPPORT_SPL
 455
 456 config TARGET_APF27
 457         bool "Support apf27"
 458         select CPU_ARM926EJS
 459         select SUPPORT_SPL
 460
 461 config ORION5X
 462         bool "Marvell Orion"
 463         select CPU_ARM926EJS
 464
 465 config TARGET_SPEAR300
 466         bool "Support spear300"
 467         select BOARD_EARLY_INIT_F
 468         select CPU_ARM926EJS
 469         select PL011_SERIAL
 470         imply CMD_SAVES
 471
 472 config TARGET_SPEAR310
 473         bool "Support spear310"
 474         select BOARD_EARLY_INIT_F
 475         select CPU_ARM926EJS
 476         select PL011_SERIAL
 477         imply CMD_SAVES
 478
 479 config TARGET_SPEAR320
 480         bool "Support spear320"
 481         select BOARD_EARLY_INIT_F
 482         select CPU_ARM926EJS
 483         select PL011_SERIAL
 484         imply CMD_SAVES
 485
 486 config TARGET_SPEAR600
 487         bool "Support spear600"
 488         select BOARD_EARLY_INIT_F
 489         select CPU_ARM926EJS
 490         select PL011_SERIAL
 491         imply CMD_SAVES
 492
 493 config TARGET_STV0991
 494         bool "Support stv0991"
 495         select CPU_V7A
 496         select DM
 497         select DM_SERIAL
 498         select DM_SPI
 499         select DM_SPI_FLASH
 500         select PL01X_SERIAL
 501         select SPI
 502         select SPI_FLASH
 503         imply CMD_DM
 504
 505 config TARGET_X600
 506         bool "Support x600"
 507         select BOARD_LATE_INIT
 508         select CPU_ARM926EJS
 509         select PL011_SERIAL
 510         select SUPPORT_SPL
 511
 512 config TARGET_WOODBURN
 513         bool "Support woodburn"
 514         select CPU_ARM1136
 515
 516 config TARGET_WOODBURN_SD
 517         bool "Support woodburn_sd"
 518         select CPU_ARM1136
 519         select SUPPORT_SPL
 520
 521 config TARGET_FLEA3
 522         bool "Support flea3"
 523         select CPU_ARM1136
 524
 525 config TARGET_MX35PDK
 526         bool "Support mx35pdk"
 527         select BOARD_LATE_INIT
 528         select CPU_ARM1136
 529
 530 config ARCH_BCM283X
 531         bool "Broadcom BCM283X family"
 532         select DM
 533         select DM_GPIO
 534         select DM_SERIAL
 535         select OF_CONTROL
 536         select PL01X_SERIAL
 537         select SERIAL_SEARCH_ALL
 538         imply CMD_DM
 539         imply FAT_WRITE
 540
 541 config TARGET_VEXPRESS_CA15_TC2
 542         bool "Support vexpress_ca15_tc2"
 543         select CPU_V7A
 544         select CPU_V7_HAS_NONSEC
 545         select CPU_V7_HAS_VIRT
 546         select PL011_SERIAL
 547
 548 config ARCH_BCMSTB
 549         bool "Broadcom BCM7XXX family"
 550         select CPU_V7A
 551         select DM
 552         select OF_CONTROL
 553         select OF_PRIOR_STAGE
 554         imply CMD_DM
 555         help
 556           This enables support for Broadcom ARM-based set-top box
 557           chipsets, including the 7445 family of chips.
 558
 559 config TARGET_VEXPRESS_CA5X2
 560         bool "Support vexpress_ca5x2"
 561         select CPU_V7A
 562         select PL011_SERIAL
 563
 564 config TARGET_VEXPRESS_CA9X4
 565         bool "Support vexpress_ca9x4"
 566         select CPU_V7A
 567         select PL011_SERIAL
 568
 569 config TARGET_BCM23550_W1D
 570         bool "Support bcm23550_w1d"
 571         select CPU_V7A
 572         imply CRC32_VERIFY
 573         imply FAT_WRITE
 574
 575 config TARGET_BCM28155_AP
 576         bool "Support bcm28155_ap"
 577         select CPU_V7A
 578         imply CRC32_VERIFY
 579         imply FAT_WRITE
 580
 581 config TARGET_BCMCYGNUS
 582         bool "Support bcmcygnus"
 583         select CPU_V7A
 584         imply BCM_SF2_ETH
 585         imply BCM_SF2_ETH_GMAC
 586         imply CMD_HASH
 587         imply CRC32_VERIFY
 588         imply FAT_WRITE
 589         imply HASH_VERIFY
 590         imply NETDEVICES
 591
 592 config TARGET_BCMNSP
 593         bool "Support bcmnsp"
 594         select CPU_V7A
 595
 596 config TARGET_BCMNS2
 597         bool "Support Broadcom Northstar2"
 598         select ARM64
 599         help
 600           Support for Broadcom Northstar 2 SoCs.  NS2 is a quad-core 64-bit
 601           ARMv8 Cortex-A57 processors targeting a broad range of networking
 602           applications
 603
 604 config ARCH_EXYNOS
 605         bool "Samsung EXYNOS"
 606         select DM
 607         select DM_GPIO
 608         select DM_I2C
 609         select DM_KEYBOARD
 610         select DM_SERIAL
 611         select DM_SPI
 612         select DM_SPI_FLASH
 613         select SPI
 614         imply CMD_DM
 615         imply FAT_WRITE
 616
 617 config ARCH_S5PC1XX
 618         bool "Samsung S5PC1XX"
 619         select CPU_V7A
 620         select DM
 621         select DM_GPIO
 622         select DM_I2C
 623         select DM_SERIAL
 624         imply CMD_DM
 625
 626 config ARCH_HIGHBANK
 627         bool "Calxeda Highbank"
 628         select CPU_V7A
 629         select PL011_SERIAL
 630
 631 config ARCH_INTEGRATOR
 632         bool "ARM Ltd. Integrator family"
 633         select DM
 634         select DM_SERIAL
 635         select PL01X_SERIAL
 636         imply CMD_DM
 637
 638 config ARCH_KEYSTONE
 639         bool "TI Keystone"
 640         select CMD_POWEROFF
 641         select CPU_V7A
 642         select SUPPORT_SPL
 643         select SYS_ARCH_TIMER
 644         select SYS_THUMB_BUILD
 645         imply CMD_MTDPARTS
 646         imply CMD_SAVES
 647         imply FIT
 648
 649 config ARCH_K3
 650         bool "Texas Instruments' K3 Architecture"
 651         select SPL
 652         select SUPPORT_SPL
 653         select FIT
 654
 655 config ARCH_OMAP2PLUS
 656         bool "TI OMAP2+"
 657         select CPU_V7A
 658         select SPL_BOARD_INIT if SPL
 659         select SPL_STACK_R if SPL
 660         select SUPPORT_SPL
 661         imply FIT
 662
 663 config ARCH_MESON
 664         bool "Amlogic Meson"
 665         imply DISTRO_DEFAULTS
 666         help
 667           Support for the Meson SoC family developed by Amlogic Inc.,
 668           targeted at media players and tablet computers. We currently
 669           support the S905 (GXBaby) 64-bit SoC.
 670
 671 config ARCH_IMX8
 672         bool "NXP i.MX8 platform"
 673         select ARM64
 674         select DM
 675         select OF_CONTROL
 676
 677 config ARCH_MX8M
 678         bool "NXP i.MX8M platform"
 679         select ARM64
 680         select DM
 681         select SUPPORT_SPL
 682         imply CMD_DM
 683
 684 config ARCH_MX23
 685         bool "NXP i.MX23 family"
 686         select CPU_ARM926EJS
 687         select PL011_SERIAL
 688         select SUPPORT_SPL
 689
 690 config ARCH_MX25
 691         bool "NXP MX25"
 692         select CPU_ARM926EJS
 693         imply MXC_GPIO
 694
 695 config ARCH_MX28
 696         bool "NXP i.MX28 family"
 697         select CPU_ARM926EJS
 698         select PL011_SERIAL
 699         select SUPPORT_SPL
 700
 701 config ARCH_MX31
 702         bool "NXP i.MX31 family"
 703         select CPU_ARM1136
 704
 705 config ARCH_MX7ULP
 706         bool "NXP MX7ULP"
 707         select CPU_V7A
 708         select ROM_UNIFIED_SECTIONS
 709         imply MXC_GPIO
 710
 711 config ARCH_MX7
 712         bool "Freescale MX7"
 713         select ARCH_MISC_INIT
 714         select BOARD_EARLY_INIT_F
 715         select CPU_V7A
 716         select SYS_FSL_HAS_SEC if SECURE_BOOT
 717         select SYS_FSL_SEC_COMPAT_4
 718         select SYS_FSL_SEC_LE
 719         imply MXC_GPIO
 720
 721 config ARCH_MX6
 722         bool "Freescale MX6"
 723         select CPU_V7A
 724         select SYS_FSL_HAS_SEC if SECURE_BOOT
 725         select SYS_FSL_SEC_COMPAT_4
 726         select SYS_FSL_SEC_LE
 727         select SYS_THUMB_BUILD if SPL
 728         imply MXC_GPIO
 729
 730 if ARCH_MX6
 731 config SPL_LDSCRIPT
 732         default "arch/arm/mach-omap2/u-boot-spl.lds"
 733 endif
 734
 735 config ARCH_MX5
 736         bool "Freescale MX5"
 737         select BOARD_EARLY_INIT_F
 738         select CPU_V7A
 739         imply MXC_GPIO
 740
 741 config ARCH_OWL
 742         bool "Actions Semi OWL SoCs"
 743         select ARM64
 744         select DM
 745         select DM_SERIAL
 746         select OF_CONTROL
 747         imply CMD_DM
 748
 749 config ARCH_QEMU
 750         bool "QEMU Virtual Platform"
 751         select DM
 752         select DM_SERIAL
 753         select OF_CONTROL
 754         select PL01X_SERIAL
 755         imply CMD_DM
 756         imply DM_RTC
 757         imply RTC_PL031
 758
 759 config ARCH_RMOBILE
 760         bool "Renesas ARM SoCs"
 761         select BOARD_EARLY_INIT_F
 762         select DM
 763         select DM_SERIAL
 764         imply CMD_DM
 765         imply FAT_WRITE
 766         imply SYS_THUMB_BUILD
 767
 768 config TARGET_S32V234EVB
 769         bool "Support s32v234evb"
 770         select ARM64
 771         select SYS_FSL_ERRATUM_ESDHC111
 772
 773 config ARCH_SNAPDRAGON
 774         bool "Qualcomm Snapdragon SoCs"
 775         select ARM64
 776         select DM
 777         select DM_GPIO
 778         select DM_SERIAL
 779         select MSM_SMEM
 780         select OF_CONTROL
 781         select OF_SEPARATE
 782         select SMEM
 783         select SPMI
 784         imply CMD_DM
 785
 786 config ARCH_SOCFPGA
 787         bool "Altera SOCFPGA family"
 788         select ARCH_EARLY_INIT_R
 789         select ARCH_MISC_INIT if !TARGET_SOCFPGA_ARRIA10
 790         select ARM64 if TARGET_SOCFPGA_STRATIX10
 791         select CPU_V7A if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
 792         select DM
 793         select DM_SERIAL
 794         select ENABLE_ARM_SOC_BOOT0_HOOK if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
 795         select OF_CONTROL
 796         select SPL_DM_RESET if DM_RESET
 797         select SPL_DM_SERIAL
 798         select SPL_LIBCOMMON_SUPPORT
 799         select SPL_LIBDISK_SUPPORT
 800         select SPL_LIBGENERIC_SUPPORT
 801         select SPL_MMC_SUPPORT if DM_MMC
 802         select SPL_NAND_SUPPORT if SPL_NAND_DENALI
 803         select SPL_OF_CONTROL
 804         select SPL_SEPARATE_BSS if TARGET_SOCFPGA_STRATIX10
 805         select SPL_SERIAL_SUPPORT
 806         select SPL_SPI_FLASH_SUPPORT if SPL_SPI_SUPPORT
 807         select SPL_SPI_SUPPORT if DM_SPI
 808         select SPL_WATCHDOG_SUPPORT
 809         select SUPPORT_SPL
 810         select SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION_TYPE
 811         select SYS_NS16550
 812         select SYS_THUMB_BUILD if TARGET_SOCFPGA_GEN5 || TARGET_SOCFPGA_ARRIA10
 813         imply CMD_DM
 814         imply CMD_MTDPARTS
 815         imply CRC32_VERIFY
 816         imply DM_SPI
 817         imply DM_SPI_FLASH
 818         imply FAT_WRITE
 819         imply SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION
 820
 821 config ARCH_SUNXI
 822         bool "Support sunxi (Allwinner) SoCs"
 823         select BINMAN
 824         select CMD_GPIO
 825         select CMD_MMC if MMC
 826         select CMD_USB if DISTRO_DEFAULTS
 827         select DM
 828         select DM_ETH
 829         select DM_GPIO
 830         select DM_KEYBOARD
 831         select DM_SERIAL
 832         select DM_USB if DISTRO_DEFAULTS
 833         select OF_BOARD_SETUP
 834         select OF_CONTROL
 835         select OF_SEPARATE
 836         select SPECIFY_CONSOLE_INDEX
 837         select SPL_STACK_R if SPL
 838         select SPL_SYS_MALLOC_SIMPLE if SPL
 839         select SPL_SYS_THUMB_BUILD if !ARM64
 840         select SYS_NS16550
 841         select SYS_THUMB_BUILD if !ARM64
 842         select USB if DISTRO_DEFAULTS
 843         select USB_KEYBOARD if DISTRO_DEFAULTS
 844         select USB_STORAGE if DISTRO_DEFAULTS
 845         select USE_TINY_PRINTF
 846         imply CMD_DM
 847         imply CMD_GPT
 848         imply CMD_UBI if NAND
 849         imply DISTRO_DEFAULTS
 850         imply FAT_WRITE
 851         imply OF_LIBFDT_OVERLAY
 852         imply PRE_CONSOLE_BUFFER
 853         imply SPL_GPIO_SUPPORT
 854         imply SPL_LIBCOMMON_SUPPORT
 855         imply SPL_LIBDISK_SUPPORT
 856         imply SPL_LIBGENERIC_SUPPORT
 857         imply SPL_MMC_SUPPORT if MMC
 858         imply SPL_POWER_SUPPORT
 859         imply SPL_SERIAL_SUPPORT
 860         imply USB_GADGET
 861
 862 config ARCH_VF610
 863         bool "Freescale Vybrid"
 864         select CPU_V7A
 865         select SYS_FSL_ERRATUM_ESDHC111
 866         imply CMD_MTDPARTS
 867         imply NAND
 868
 869 config ARCH_ZYNQ
 870         bool "Xilinx Zynq based platform"
 871         select BOARD_EARLY_INIT_F if WDT
 872         select CLK
 873         select CLK_ZYNQ
 874         select CPU_V7A
 875         select DM
 876         select DM_ETH if NET
 877         select DM_MMC if MMC
 878         select DM_SERIAL
 879         select DM_SPI
 880         select DM_SPI_FLASH
 881         select DM_USB if USB
 882         select OF_CONTROL
 883         select SPI
 884         select SPL_BOARD_INIT if SPL
 885         select SPL_CLK if SPL
 886         select SPL_DM if SPL
 887         select SPL_OF_CONTROL if SPL
 888         select SPL_SEPARATE_BSS if SPL
 889         select SUPPORT_SPL
 890         imply ARCH_EARLY_INIT_R
 891         imply BOARD_LATE_INIT
 892         imply CMD_CLK
 893         imply CMD_DM
 894         imply CMD_SPL
 895         imply FAT_WRITE
 896
 897 config ARCH_ZYNQMP_R5
 898         bool "Xilinx ZynqMP R5 based platform"
 899         select CLK
 900         select CPU_V7R
 901         select DM
 902         select DM_SERIAL
 903         select OF_CONTROL
 904         imply CMD_DM
 905
 906 config ARCH_ZYNQMP
 907         bool "Xilinx ZynqMP based platform"
 908         select ARM64
 909         select CLK
 910         select DM
 911         select DM_SERIAL
 912         select DM_USB if USB
 913         select OF_CONTROL
 914         select SPL_BOARD_INIT if SPL
 915         select SPL_CLK if SPL
 916         select SUPPORT_SPL
 917         imply BOARD_LATE_INIT
 918         imply CMD_DM
 919         imply FAT_WRITE
 920
 921 config TEGRA
 922         bool "NVIDIA Tegra"
 923         imply DISTRO_DEFAULTS
 924         imply FAT_WRITE
 925
 926 config TARGET_VEXPRESS64_AEMV8A
 927         bool "Support vexpress_aemv8a"
 928         select ARM64
 929         select PL01X_SERIAL
 930
 931 config TARGET_VEXPRESS64_BASE_FVP
 932         bool "Support Versatile Express ARMv8a FVP BASE model"
 933         select ARM64
 934         select PL01X_SERIAL
 935         select SEMIHOSTING
 936
 937 config TARGET_VEXPRESS64_BASE_FVP_DRAM
 938         bool "Support Versatile Express ARMv8a FVP BASE model booting from DRAM"
 939         select ARM64
 940         select PL01X_SERIAL
 941         help
 942           This target is derived from TARGET_VEXPRESS64_BASE_FVP and over-rides
 943           the default config to allow the user to load the images directly into
 944           DRAM using model parameters rather than by using semi-hosting to load
 945           the files from the host filesystem.
 946
 947 config TARGET_VEXPRESS64_JUNO
 948         bool "Support Versatile Express Juno Development Platform"
 949         select ARM64
 950         select PL01X_SERIAL
 951
 952 config TARGET_LS2080A_EMU
 953         bool "Support ls2080a_emu"
 954         select ARCH_LS2080A
 955         select ARCH_MISC_INIT
 956         select ARM64
 957         select ARMV8_MULTIENTRY
 958         help
 959           Support for Freescale LS2080A_EMU platform
 960           The LS2080A Development System (EMULATOR) is a pre silicon
 961           development platform that supports the QorIQ LS2080A
 962           Layerscape Architecture processor.
 963
 964 config TARGET_LS2080A_SIMU
 965         bool "Support ls2080a_simu"
 966         select ARCH_LS2080A
 967         select ARCH_MISC_INIT
 968         select ARM64
 969         select ARMV8_MULTIENTRY
 970         help
 971           Support for Freescale LS2080A_SIMU platform
 972           The LS2080A Development System (QDS) is a pre silicon
 973           development platform that supports the QorIQ LS2080A
 974           Layerscape Architecture processor.
 975
 976 config TARGET_LS1088AQDS
 977         bool "Support ls1088aqds"
 978         select ARCH_LS1088A
 979         select ARCH_MISC_INIT
 980         select ARM64
 981         select ARMV8_MULTIENTRY
 982         select BOARD_LATE_INIT
 983         select SUPPORT_SPL
 984         help
 985           Support for NXP LS1088AQDS platform
 986           The LS1088A Development System (QDS) is a high-performance
 987           development platform that supports the QorIQ LS1088A
 988           Layerscape Architecture processor.
 989
 990 config TARGET_LS2080AQDS
 991         bool "Support ls2080aqds"
 992         select ARCH_LS2080A
 993         select ARCH_MISC_INIT
 994         select ARM64
 995         select ARMV8_MULTIENTRY
 996         select BOARD_LATE_INIT
 997         select SUPPORT_SPL
 998         imply SCSI
 999         imply SCSI_AHCI
1000         help
1001           Support for Freescale LS2080AQDS platform
1002           The LS2080A Development System (QDS) is a high-performance
1003           development platform that supports the QorIQ LS2080A
1004           Layerscape Architecture processor.
1005
1006 config TARGET_LS2080ARDB
1007         bool "Support ls2080ardb"
1008         select ARCH_LS2080A
1009         select ARCH_MISC_INIT
1010         select ARM64
1011         select ARMV8_MULTIENTRY
1012         select BOARD_LATE_INIT
1013         select SUPPORT_SPL
1014         imply SCSI
1015         imply SCSI_AHCI
1016         help
1017           Support for Freescale LS2080ARDB platform.
1018           The LS2080A Reference design board (RDB) is a high-performance
1019           development platform that supports the QorIQ LS2080A
1020           Layerscape Architecture processor.
1021
1022 config TARGET_LS2081ARDB
1023         bool "Support ls2081ardb"
1024         select ARCH_LS2080A
1025         select ARCH_MISC_INIT
1026         select ARM64
1027         select ARMV8_MULTIENTRY
1028         select BOARD_LATE_INIT
1029         select SUPPORT_SPL
1030         help
1031           Support for Freescale LS2081ARDB platform.
1032           The LS2081A Reference design board (RDB) is a high-performance
1033           development platform that supports the QorIQ LS2081A/LS2041A
1034           Layerscape Architecture processor.
1035
1036 config TARGET_HIKEY
1037         bool "Support HiKey 96boards Consumer Edition Platform"
1038         select ARM64
1039         select DM
1040         select DM_GPIO
1041         select DM_SERIAL
1042         select OF_CONTROL
1043         select PL01X_SERIAL
1044         select SPECIFY_CONSOLE_INDEX
1045         imply CMD_DM
1046           help
1047           Support for HiKey 96boards platform. It features a HI6220
1048           SoC, with 8xA53 CPU, mali450 gpu, and 1GB RAM.
1049
1050 config TARGET_POPLAR
1051         bool "Support Poplar 96boards Enterprise Edition Platform"
1052         select ARM64
1053         select DM
1054         select DM_SERIAL
1055         select DM_USB
1056         select OF_CONTROL
1057         select PL01X_SERIAL
1058         imply CMD_DM
1059           help
1060           Support for Poplar 96boards EE platform. It features a HI3798cv200
1061           SoC, with 4xA53 CPU, 1GB RAM and the high performance Mali T720 GPU
1062           making it capable of running any commercial set-top solution based on
1063           Linux or Android.
1064
1065 config TARGET_LS1012AQDS
1066         bool "Support ls1012aqds"
1067         select ARCH_LS1012A
1068         select ARM64
1069         select BOARD_LATE_INIT
1070         help
1071           Support for Freescale LS1012AQDS platform.
1072           The LS1012A Development System (QDS) is a high-performance
1073           development platform that supports the QorIQ LS1012A
1074           Layerscape Architecture processor.
1075
1076 config TARGET_LS1012ARDB
1077         bool "Support ls1012ardb"
1078         select ARCH_LS1012A
1079         select ARM64
1080         select BOARD_LATE_INIT
1081         imply SCSI
1082         imply SCSI_AHCI
1083         help
1084           Support for Freescale LS1012ARDB platform.
1085           The LS1012A Reference design board (RDB) is a high-performance
1086           development platform that supports the QorIQ LS1012A
1087           Layerscape Architecture processor.
1088
1089 config TARGET_LS1012A2G5RDB
1090         bool "Support ls1012a2g5rdb"
1091         select ARCH_LS1012A
1092         select ARM64
1093         select BOARD_LATE_INIT
1094         imply SCSI
1095         help
1096           Support for Freescale LS1012A2G5RDB platform.
1097           The LS1012A 2G5 Reference design board (RDB) is a high-performance
1098           development platform that supports the QorIQ LS1012A
1099           Layerscape Architecture processor.
1100
1101 config TARGET_LS1012AFRWY
1102         bool "Support ls1012afrwy"
1103         select ARCH_LS1012A
1104         select ARM64
1105         select BOARD_LATE_INIT
1106         imply SCSI
1107         imply SCSI_AHCI
1108         help
1109          Support for Freescale LS1012AFRWY platform.
1110          The LS1012A FRWY board (FRWY) is a high-performance
1111          development platform that supports the QorIQ LS1012A
1112          Layerscape Architecture processor.
1113
1114 config TARGET_LS1012AFRDM
1115         bool "Support ls1012afrdm"
1116         select ARCH_LS1012A
1117         select ARM64
1118         help
1119           Support for Freescale LS1012AFRDM platform.
1120           The LS1012A Freedom  board (FRDM) is a high-performance
1121           development platform that supports the QorIQ LS1012A
1122           Layerscape Architecture processor.
1123
1124 config TARGET_LS1088ARDB
1125         bool "Support ls1088ardb"
1126         select ARCH_LS1088A
1127         select ARCH_MISC_INIT
1128         select ARM64
1129         select ARMV8_MULTIENTRY
1130         select BOARD_LATE_INIT
1131         select SUPPORT_SPL
1132         help
1133           Support for NXP LS1088ARDB platform.
1134           The LS1088A Reference design board (RDB) is a high-performance
1135           development platform that supports the QorIQ LS1088A
1136           Layerscape Architecture processor.
1137
1138 config TARGET_LS1021AQDS
1139         bool "Support ls1021aqds"
1140         select ARCH_LS1021A
1141         select ARCH_SUPPORT_PSCI
1142         select BOARD_EARLY_INIT_F
1143         select BOARD_LATE_INIT
1144         select CPU_V7A
1145         select CPU_V7_HAS_NONSEC
1146         select CPU_V7_HAS_VIRT
1147         select LS1_DEEP_SLEEP
1148         select SUPPORT_SPL
1149         select SYS_FSL_DDR
1150         imply SCSI
1151
1152 config TARGET_LS1021ATWR
1153         bool "Support ls1021atwr"
1154         select ARCH_LS1021A
1155         select ARCH_SUPPORT_PSCI
1156         select BOARD_EARLY_INIT_F
1157         select BOARD_LATE_INIT
1158         select CPU_V7A
1159         select CPU_V7_HAS_NONSEC
1160         select CPU_V7_HAS_VIRT
1161         select LS1_DEEP_SLEEP
1162         select SUPPORT_SPL
1163         imply SCSI
1164
1165 config TARGET_LS1021AIOT
1166         bool "Support ls1021aiot"
1167         select ARCH_LS1021A
1168         select ARCH_SUPPORT_PSCI
1169         select BOARD_LATE_INIT
1170         select CPU_V7A
1171         select CPU_V7_HAS_NONSEC
1172         select CPU_V7_HAS_VIRT
1173         select SUPPORT_SPL
1174         imply SCSI
1175         help
1176           Support for Freescale LS1021AIOT platform.
1177           The LS1021A Freescale board (IOT) is a high-performance
1178           development platform that supports the QorIQ LS1021A
1179           Layerscape Architecture processor.
1180
1181 config TARGET_LS1043AQDS
1182         bool "Support ls1043aqds"
1183         select ARCH_LS1043A
1184         select ARM64
1185         select ARMV8_MULTIENTRY
1186         select BOARD_EARLY_INIT_F
1187         select BOARD_LATE_INIT
1188         select SUPPORT_SPL
1189         imply SCSI
1190         help
1191           Support for Freescale LS1043AQDS platform.
1192
1193 config TARGET_LS1043ARDB
1194         bool "Support ls1043ardb"
1195         select ARCH_LS1043A
1196         select ARM64
1197         select ARMV8_MULTIENTRY
1198         select BOARD_EARLY_INIT_F
1199         select BOARD_LATE_INIT
1200         select SUPPORT_SPL
1201         imply SCSI
1202         help
1203           Support for Freescale LS1043ARDB platform.
1204
1205 config TARGET_LS1046AQDS
1206         bool "Support ls1046aqds"
1207         select ARCH_LS1046A
1208         select ARM64
1209         select ARMV8_MULTIENTRY
1210         select BOARD_EARLY_INIT_F
1211         select BOARD_LATE_INIT
1212         select DM_SPI_FLASH if DM_SPI
1213         select SUPPORT_SPL
1214         imply SCSI
1215         help
1216           Support for Freescale LS1046AQDS platform.
1217           The LS1046A Development System (QDS) is a high-performance
1218           development platform that supports the QorIQ LS1046A
1219           Layerscape Architecture processor.
1220
1221 config TARGET_LS1046ARDB
1222         bool "Support ls1046ardb"
1223         select ARCH_LS1046A
1224         select ARM64
1225         select ARMV8_MULTIENTRY
1226         select BOARD_EARLY_INIT_F
1227         select BOARD_LATE_INIT
1228         select DM_SPI_FLASH if DM_SPI
1229         select POWER_MC34VR500
1230         select SUPPORT_SPL
1231         imply SCSI
1232         help
1233           Support for Freescale LS1046ARDB platform.
1234           The LS1046A Reference Design Board (RDB) is a high-performance
1235           development platform that supports the QorIQ LS1046A
1236           Layerscape Architecture processor.
1237
1238 config TARGET_H2200
1239         bool "Support h2200"
1240         select CPU_PXA
1241
1242 config TARGET_ZIPITZ2
1243         bool "Support zipitz2"
1244         select CPU_PXA
1245
1246 config TARGET_COLIBRI_PXA270
1247         bool "Support colibri_pxa270"
1248         select CPU_PXA
1249
1250 config ARCH_UNIPHIER
1251         bool "Socionext UniPhier SoCs"
1252         select BOARD_LATE_INIT
1253         select DM
1254         select DM_GPIO
1255         select DM_I2C
1256         select DM_MMC
1257         select DM_RESET
1258         select DM_SERIAL
1259         select DM_USB
1260         select OF_BOARD_SETUP
1261         select OF_CONTROL
1262         select OF_LIBFDT
1263         select PINCTRL
1264         select SPL_BOARD_INIT if SPL
1265         select SPL_DM if SPL
1266         select SPL_LIBCOMMON_SUPPORT if SPL
1267         select SPL_LIBGENERIC_SUPPORT if SPL
1268         select SPL_OF_CONTROL if SPL
1269         select SPL_PINCTRL if SPL
1270         select SUPPORT_SPL
1271         imply CMD_DM
1272         imply DISTRO_DEFAULTS
1273         imply FAT_WRITE
1274         help
1275           Support for UniPhier SoC family developed by Socionext Inc.
1276           (formerly, System LSI Business Division of Panasonic Corporation)
1277
1278 config STM32
1279         bool "Support STMicroelectronics STM32 MCU with cortex M"
1280         select CPU_V7M
1281         select DM
1282         select DM_SERIAL
1283         imply CMD_DM
1284
1285 config ARCH_STI
1286         bool "Support STMicrolectronics SoCs"
1287         select BLK
1288         select CPU_V7A
1289         select DM
1290         select DM_MMC
1291         select DM_RESET
1292         select DM_SERIAL
1293         imply CMD_DM
1294         help
1295           Support for STMicroelectronics STiH407/10 SoC family.
1296           This SoC is used on Linaro 96Board STiH410-B2260
1297
1298 config ARCH_STM32MP
1299         bool "Support STMicroelectronics STM32MP Socs with cortex A"
1300         select ARCH_MISC_INIT
1301         select BOARD_LATE_INIT
1302         select CLK
1303         select DM
1304         select DM_GPIO
1305         select DM_RESET
1306         select DM_SERIAL
1307         select MISC
1308         select OF_CONTROL
1309         select OF_LIBFDT
1310         select PINCTRL
1311         select REGMAP
1312         select SUPPORT_SPL
1313         select SYSCON
1314         select SYSRESET
1315         select SYS_THUMB_BUILD
1316         imply CMD_DM
1317         help
1318           Support for STM32MP SoC family developed by STMicroelectronics,
1319           MPUs based on ARM cortex A core
1320           U-BOOT is running in DDR and SPL support is the unsecure First Stage
1321           BootLoader (FSBL)
1322
1323 config ARCH_ROCKCHIP
1324         bool "Support Rockchip SoCs"
1325         select BLK
1326         select DM
1327         select DM_GPIO
1328         select DM_I2C
1329         select DM_MMC
1330         select DM_PWM
1331         select DM_REGULATOR
1332         select DM_SERIAL
1333         select DM_SPI
1334         select DM_SPI_FLASH
1335         select DM_USB if USB
1336         select ENABLE_ARM_SOC_BOOT0_HOOK
1337         select OF_CONTROL
1338         select SPI
1339         select SPL_DM if SPL
1340         select SPL_SYS_MALLOC_SIMPLE if SPL
1341         select SYS_MALLOC_F
1342         select SYS_THUMB_BUILD if !ARM64
1343         imply ADC
1344         imply CMD_DM
1345         imply DISTRO_DEFAULTS
1346         imply FAT_WRITE
1347         imply SARADC_ROCKCHIP
1348         imply SPL_SYSRESET
1349         imply SYS_NS16550
1350         imply TPL_SYSRESET
1351         imply USB_FUNCTION_FASTBOOT
1352
1353 config TARGET_THUNDERX_88XX
1354         bool "Support ThunderX 88xx"
1355         select ARM64
1356         select OF_CONTROL
1357         select PL01X_SERIAL
1358         select SYS_CACHE_SHIFT_7
1359
1360 config ARCH_ASPEED
1361         bool "Support Aspeed SoCs"
1362         select DM
1363         select OF_CONTROL
1364         imply CMD_DM
1365
1366 endchoice
1367
1368 config TI_SECURE_DEVICE
1369         bool "HS Device Type Support"
1370         depends on ARCH_KEYSTONE || ARCH_OMAP2PLUS
1371         help
1372           If a high secure (HS) device type is being used, this config
1373           must be set. This option impacts various aspects of the
1374           build system (to create signed boot images that can be
1375           authenticated) and the code. See the doc/README.ti-secure
1376           file for further details.
1377
1378 source "arch/arm/mach-aspeed/Kconfig"
1379
1380 source "arch/arm/mach-at91/Kconfig"
1381
1382 source "arch/arm/mach-bcm283x/Kconfig"
1383
1384 source "arch/arm/mach-bcmstb/Kconfig"
1385
1386 source "arch/arm/mach-davinci/Kconfig"
1387
1388 source "arch/arm/mach-exynos/Kconfig"
1389
1390 source "arch/arm/mach-highbank/Kconfig"
1391
1392 source "arch/arm/mach-integrator/Kconfig"
1393
1394 source "arch/arm/mach-k3/Kconfig"
1395
1396 source "arch/arm/mach-keystone/Kconfig"
1397
1398 source "arch/arm/mach-kirkwood/Kconfig"
1399
1400 source "arch/arm/mach-mvebu/Kconfig"
1401
1402 source "arch/arm/cpu/armv7/ls102xa/Kconfig"
1403
1404 source "arch/arm/mach-imx/mx2/Kconfig"
1405
1406 source "arch/arm/mach-imx/mx3/Kconfig"
1407
1408 source "arch/arm/mach-imx/mx5/Kconfig"
1409
1410 source "arch/arm/mach-imx/mx6/Kconfig"
1411
1412 source "arch/arm/mach-imx/mx7/Kconfig"
1413
1414 source "arch/arm/mach-imx/mx7ulp/Kconfig"
1415
1416 source "arch/arm/mach-imx/imx8/Kconfig"
1417
1418 source "arch/arm/mach-imx/mx8m/Kconfig"
1419
1420 source "arch/arm/mach-imx/mxs/Kconfig"
1421
1422 source "arch/arm/mach-omap2/Kconfig"
1423
1424 source "arch/arm/cpu/armv8/fsl-layerscape/Kconfig"
1425
1426 source "arch/arm/mach-orion5x/Kconfig"
1427
1428 source "arch/arm/mach-owl/Kconfig"
1429
1430 source "arch/arm/mach-rmobile/Kconfig"
1431
1432 source "arch/arm/mach-meson/Kconfig"
1433
1434 source "arch/arm/mach-qemu/Kconfig"
1435
1436 source "arch/arm/mach-rockchip/Kconfig"
1437
1438 source "arch/arm/mach-s5pc1xx/Kconfig"
1439
1440 source "arch/arm/mach-snapdragon/Kconfig"
1441
1442 source "arch/arm/mach-socfpga/Kconfig"
1443
1444 source "arch/arm/mach-sti/Kconfig"
1445
1446 source "arch/arm/mach-stm32/Kconfig"
1447
1448 source "arch/arm/mach-stm32mp/Kconfig"
1449
1450 source "arch/arm/mach-sunxi/Kconfig"
1451
1452 source "arch/arm/mach-tegra/Kconfig"
1453
1454 source "arch/arm/mach-uniphier/Kconfig"
1455
1456 source "arch/arm/cpu/armv7/vf610/Kconfig"
1457
1458 source "arch/arm/mach-zynq/Kconfig"
1459
1460 source "arch/arm/mach-zynqmp-r5/Kconfig"
1461
1462 source "arch/arm/cpu/armv7/Kconfig"
1463
1464 source "arch/arm/cpu/armv8/zynqmp/Kconfig"
1465
1466 source "arch/arm/cpu/armv8/Kconfig"
1467
1468 source "arch/arm/mach-imx/Kconfig"
1469
1470 source "board/bosch/shc/Kconfig"
1471 source "board/CarMediaLab/flea3/Kconfig"
1472 source "board/Marvell/aspenite/Kconfig"
1473 source "board/Marvell/gplugd/Kconfig"
1474 source "board/armadeus/apf27/Kconfig"
1475 source "board/armltd/vexpress/Kconfig"
1476 source "board/armltd/vexpress64/Kconfig"
1477 source "board/broadcom/bcm23550_w1d/Kconfig"
1478 source "board/broadcom/bcm28155_ap/Kconfig"
1479 source "board/broadcom/bcmcygnus/Kconfig"
1480 source "board/broadcom/bcmnsp/Kconfig"
1481 source "board/broadcom/bcmns2/Kconfig"
1482 source "board/cavium/thunderx/Kconfig"
1483 source "board/cirrus/edb93xx/Kconfig"
1484 source "board/eets/pdu001/Kconfig"
1485 source "board/freescale/ls2080a/Kconfig"
1486 source "board/freescale/ls2080aqds/Kconfig"
1487 source "board/freescale/ls2080ardb/Kconfig"
1488 source "board/freescale/ls1088a/Kconfig"
1489 source "board/freescale/ls1021aqds/Kconfig"
1490 source "board/freescale/ls1043aqds/Kconfig"
1491 source "board/freescale/ls1021atwr/Kconfig"
1492 source "board/freescale/ls1021aiot/Kconfig"
1493 source "board/freescale/ls1046aqds/Kconfig"
1494 source "board/freescale/ls1043ardb/Kconfig"
1495 source "board/freescale/ls1046ardb/Kconfig"
1496 source "board/freescale/ls1012aqds/Kconfig"
1497 source "board/freescale/ls1012ardb/Kconfig"
1498 source "board/freescale/ls1012afrdm/Kconfig"
1499 source "board/freescale/mx35pdk/Kconfig"
1500 source "board/freescale/s32v234evb/Kconfig"
1501 source "board/grinn/chiliboard/Kconfig"
1502 source "board/gumstix/pepper/Kconfig"
1503 source "board/h2200/Kconfig"
1504 source "board/hisilicon/hikey/Kconfig"
1505 source "board/hisilicon/poplar/Kconfig"
1506 source "board/isee/igep003x/Kconfig"
1507 source "board/phytec/pcm051/Kconfig"
1508 source "board/silica/pengwyn/Kconfig"
1509 source "board/spear/spear300/Kconfig"
1510 source "board/spear/spear310/Kconfig"
1511 source "board/spear/spear320/Kconfig"
1512 source "board/spear/spear600/Kconfig"
1513 source "board/spear/x600/Kconfig"
1514 source "board/st/stv0991/Kconfig"
1515 source "board/tcl/sl50/Kconfig"
1516 source "board/ucRobotics/bubblegum_96/Kconfig"
1517 source "board/birdland/bav335x/Kconfig"
1518 source "board/timll/devkit3250/Kconfig"
1519 source "board/toradex/colibri_pxa270/Kconfig"
1520 source "board/vscom/baltos/Kconfig"
1521 source "board/woodburn/Kconfig"
1522 source "board/work-microwave/work_92105/Kconfig"
1523 source "board/xilinx/Kconfig"
1524 source "board/xilinx/zynq/Kconfig"
1525 source "board/xilinx/zynqmp/Kconfig"
1526 source "board/zipitz2/Kconfig"
1527
1528 source "arch/arm/Kconfig.debug"
1529
1530 endmenu
1531
1532 config SPL_LDSCRIPT
1533         default "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" if (ARCH_MX23 || ARCH_MX28) && !SPL_FRAMEWORK
1534         default "arch/arm/cpu/arm1136/u-boot-spl.lds" if CPU_ARM1136
1535         default "arch/arm/cpu/armv8/u-boot-spl.lds" if ARM64
1536
1537