]> git.ipfire.org Git - people/ms/u-boot.git/blob - arch/arm/mach-mvebu/include/mach/config.h
arm: mvebu: Add DM and OF_CONTROL support to SPL
[people/ms/u-boot.git] / arch / arm / mach-mvebu / include / mach / config.h
1 /*
2 * (C) Copyright 2011
3 * Marvell Semiconductor <www.marvell.com>
4 * Written-by: Lei Wen <leiwen@marvell.com>
5 *
6 * SPDX-License-Identifier: GPL-2.0+
7 */
8
9 /*
10 * This file should be included in board config header file.
11 *
12 * It supports common definitions for MVEBU platforms
13 */
14
15 #ifndef _MVEBU_CONFIG_H
16 #define _MVEBU_CONFIG_H
17
18 #include <asm/arch/soc.h>
19
20 #if defined(CONFIG_ARMADA_XP)
21 #define MV88F78X60 /* for the DDR training bin_hdr code */
22 #endif
23
24 #define CONFIG_SYS_CACHELINE_SIZE 32
25
26 /*
27 * By default kwbimage.cfg from board specific folder is used
28 * If for some board, different configuration file need to be used,
29 * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
30 */
31 #ifndef CONFIG_SYS_KWD_CONFIG
32 #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
33 #endif /* CONFIG_SYS_KWD_CONFIG */
34
35 /* Add target to build it automatically upon "make" */
36 #ifdef CONFIG_SPL
37 #define CONFIG_BUILD_TARGET "u-boot-spl.kwb"
38 #endif
39
40 /* end of 16M scrubbed by training in bootrom */
41 #define CONFIG_SYS_INIT_SP_ADDR 0x00FF0000
42 #define CONFIG_NR_DRAM_BANKS_MAX 2
43
44 #define MV_UART_CONSOLE_BASE MVEBU_UART0_BASE
45
46 /*
47 * SPI Flash configuration
48 */
49 #ifdef CONFIG_CMD_SF
50 #define CONFIG_HARD_SPI 1
51 #define CONFIG_KIRKWOOD_SPI 1
52 #ifndef CONFIG_ENV_SPI_BUS
53 # define CONFIG_ENV_SPI_BUS 0
54 #endif
55 #ifndef CONFIG_ENV_SPI_CS
56 # define CONFIG_ENV_SPI_CS 0
57 #endif
58 #ifndef CONFIG_ENV_SPI_MAX_HZ
59 # define CONFIG_ENV_SPI_MAX_HZ 50000000
60 #endif
61 #endif
62
63 /*
64 * Ethernet Driver configuration
65 */
66 #ifdef CONFIG_CMD_NET
67 #define CONFIG_CMD_MII
68 #define CONFIG_MII /* expose smi ove miiphy interface */
69 #define CONFIG_MVNETA /* Enable Marvell Gbe Controller Driver */
70 #define CONFIG_PHYLIB
71 #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
72 #define CONFIG_PHY_GIGE /* GbE speed/duplex detect */
73 #define CONFIG_ARP_TIMEOUT 200
74 #define CONFIG_NET_RETRY_COUNT 50
75 #endif /* CONFIG_CMD_NET */
76
77 /*
78 * I2C related stuff
79 */
80 #ifdef CONFIG_CMD_I2C
81 #ifndef CONFIG_SYS_I2C_SOFT
82 #define CONFIG_I2C_MVTWSI
83 #endif
84 #define CONFIG_SYS_I2C_SLAVE 0x0
85 #define CONFIG_SYS_I2C_SPEED 100000
86 #endif
87
88 /* Use common timer */
89 #define CONFIG_SYS_TIMER_COUNTS_DOWN
90 #define CONFIG_SYS_TIMER_COUNTER (MVEBU_TIMER_BASE + 0x14)
91 #define CONFIG_SYS_TIMER_RATE 25000000
92
93 #endif /* __MVEBU_CONFIG_H */