2 * (C) Copyright 2015 Google, Inc
4 * SPDX-License-Identifier: GPL-2.0+
8 #include <debug_uart.h>
17 #include <asm/arch/clock.h>
18 #include <asm/arch/hardware.h>
19 #include <asm/arch/periph.h>
20 #include <asm/arch/sdram.h>
21 #include <asm/arch/timer.h>
22 #include <dm/pinctrl.h>
26 #include <power/regulator.h>
28 DECLARE_GLOBAL_DATA_PTR
;
30 u32
spl_boot_device(void)
32 #if !CONFIG_IS_ENABLED(OF_PLATDATA)
33 const void *blob
= gd
->fdt_blob
;
39 bootdev
= fdtdec_get_config_string(blob
, "u-boot,boot0");
40 debug("Boot device %s\n", bootdev
);
44 node
= fdt_path_offset(blob
, bootdev
);
46 debug("node=%d\n", node
);
49 ret
= device_get_global_by_of_offset(node
, &dev
);
51 debug("device at node %s/%d not found: %d\n", bootdev
, node
,
55 debug("Found device %s\n", dev
->name
);
56 switch (device_get_uclass_id(dev
)) {
57 case UCLASS_SPI_FLASH
:
58 return BOOT_DEVICE_SPI
;
60 return BOOT_DEVICE_MMC1
;
62 debug("Booting from device uclass '%s' not supported\n",
63 dev_get_uclass_name(dev
));
68 return BOOT_DEVICE_MMC1
;
71 u32
spl_boot_mode(const u32 boot_device
)
73 return MMCSD_MODE_RAW
;
76 /* read L2 control register (L2CTLR) */
77 static inline uint32_t read_l2ctlr(void)
81 asm volatile ("mrc p15, 1, %0, c9, c0, 2" : "=r" (val
));
86 /* write L2 control register (L2CTLR) */
87 static inline void write_l2ctlr(uint32_t val
)
90 * Note: L2CTLR can only be written when the L2 memory system
91 * is idle, ie before the MMU is enabled.
93 asm volatile("mcr p15, 1, %0, c9, c0, 2" : : "r" (val
) : "memory");
97 static void configure_l2ctlr(void)
101 l2ctlr
= read_l2ctlr();
102 l2ctlr
&= 0xfffc0000; /* clear bit0~bit17 */
105 * Data RAM write latency: 2 cycles
106 * Data RAM read latency: 2 cycles
107 * Data RAM setup latency: 1 cycle
108 * Tag RAM write latency: 1 cycle
109 * Tag RAM read latency: 1 cycle
110 * Tag RAM setup latency: 1 cycle
112 l2ctlr
|= (1 << 3 | 1 << 0);
113 write_l2ctlr(l2ctlr
);
116 #ifdef CONFIG_SPL_MMC_SUPPORT
117 static int configure_emmc(struct udevice
*pinctrl
)
119 struct gpio_desc desc
;
122 pinctrl_request_noflags(pinctrl
, PERIPH_ID_EMMC
);
125 * TODO(sjg@chromium.org): Pick this up from device tree or perhaps
126 * use the EMMC_PWREN setting.
128 ret
= dm_gpio_lookup_name("D9", &desc
);
130 debug("gpio ret=%d\n", ret
);
133 ret
= dm_gpio_request(&desc
, "emmc_pwren");
135 debug("gpio_request ret=%d\n", ret
);
138 ret
= dm_gpio_set_dir_flags(&desc
, GPIOD_IS_OUT
);
140 debug("gpio dir ret=%d\n", ret
);
143 ret
= dm_gpio_set_value(&desc
, 1);
145 debug("gpio value ret=%d\n", ret
);
153 void board_init_f(ulong dummy
)
155 struct udevice
*pinctrl
;
159 /* Example code showing how to enable the debug UART on RK3288 */
161 #include <asm/arch/grf_rk3288.h>
162 /* Enable early UART on the RK3288 */
163 #define GRF_BASE 0xff770000
164 struct rk3288_grf
* const grf
= (void *)GRF_BASE
;
166 rk_clrsetreg(&grf
->gpio7ch_iomux
, GPIO7C7_MASK
<< GPIO7C7_SHIFT
|
167 GPIO7C6_MASK
<< GPIO7C6_SHIFT
,
168 GPIO7C7_UART2DBG_SOUT
<< GPIO7C7_SHIFT
|
169 GPIO7C6_UART2DBG_SIN
<< GPIO7C6_SHIFT
);
171 * Debug UART can be used from here if required:
176 * printascii("string");
183 debug("spl_init() failed: %d\n", ret
);
187 rockchip_timer_init();
190 ret
= uclass_get_device(UCLASS_CLK
, 0, &dev
);
192 debug("CLK init failed: %d\n", ret
);
196 ret
= uclass_get_device(UCLASS_PINCTRL
, 0, &pinctrl
);
198 debug("Pinctrl init failed: %d\n", ret
);
202 ret
= uclass_get_device(UCLASS_RAM
, 0, &dev
);
204 debug("DRAM init failed: %d\n", ret
);
209 static int setup_led(void)
211 #ifdef CONFIG_SPL_LED
216 led_name
= fdtdec_get_config_string(gd
->fdt_blob
, "u-boot,boot-led");
219 ret
= led_get_by_label(led_name
, &dev
);
221 debug("%s: get=%d\n", __func__
, ret
);
224 ret
= led_set_on(dev
, 1);
232 void spl_board_init(void)
234 struct udevice
*pinctrl
;
240 debug("LED ret=%d\n", ret
);
244 ret
= uclass_get_device(UCLASS_PINCTRL
, 0, &pinctrl
);
246 debug("%s: Cannot find pinctrl device\n", __func__
);
249 #ifdef CONFIG_SPL_MMC_SUPPORT
250 if (!IS_ENABLED(CONFIG_TARGET_ROCK2
) &&
251 !IS_ENABLED(CONFIG_TARGET_FIREFLY_RK3288
)) {
252 ret
= pinctrl_request_noflags(pinctrl
, PERIPH_ID_SDCARD
);
254 debug("%s: Failed to set up SD card\n", __func__
);
257 ret
= configure_emmc(pinctrl
);
259 debug("%s: Failed to set up eMMC\n", __func__
);
265 /* Enable debug UART */
266 ret
= pinctrl_request_noflags(pinctrl
, PERIPH_ID_UART_DBG
);
268 debug("%s: Failed to set up console UART\n", __func__
);
272 preloader_console_init();
275 printf("spl_board_init: Error %d\n", ret
);
277 /* No way to report error here */
281 void lowlevel_init(void)