arch/arm/mach-uniphier/Kconfig

   1 if ARCH_UNIPHIER
   2
   3 config SYS_CONFIG_NAME
   4         default "uniphier"
   5
   6 config ARCH_UNIPHIER_32BIT
   7         bool
   8         select CPU_V7
   9         select CPU_V7_HAS_NONSEC
  10         select ARMV7_NONSEC
  11         select ARCH_SUPPORT_PSCI
  12
  13 config ARCH_UNIPHIER_64BIT
  14         bool
  15         select ARM64
  16         select SPL_SEPARATE_BSS
  17         select ARMV8_MULTIENTRY
  18         select ARMV8_SPIN_TABLE
  19
  20 choice
  21         prompt "UniPhier SoC select"
  22         default ARCH_UNIPHIER_PRO4
  23
  24 config ARCH_UNIPHIER_SLD3
  25         bool "UniPhier PH1-sLD3 SoC"
  26         select ARCH_UNIPHIER_32BIT
  27
  28 config ARCH_UNIPHIER_LD4_SLD8
  29         bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
  30         select ARCH_UNIPHIER_32BIT
  31
  32 config ARCH_UNIPHIER_PRO4
  33         bool "UniPhier PH1-Pro4 SoC"
  34         select ARCH_UNIPHIER_32BIT
  35
  36 config ARCH_UNIPHIER_PRO5_PXS2_LD6B
  37         bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
  38         select ARCH_UNIPHIER_32BIT
  39
  40 config ARCH_UNIPHIER_LD11
  41         bool "UniPhier PH1-LD11 SoC"
  42         select ARCH_UNIPHIER_64BIT
  43
  44 config ARCH_UNIPHIER_LD20
  45         bool "UniPhier PH1-LD20 SoC"
  46         select ARCH_UNIPHIER_64BIT
  47         select OF_BOARD_SETUP
  48
  49 endchoice
  50
  51 config ARCH_UNIPHIER_LD4
  52         bool "Enable UniPhier PH1-LD4 SoC support"
  53         depends on ARCH_UNIPHIER_LD4_SLD8
  54         default y
  55
  56 config ARCH_UNIPHIER_SLD8
  57         bool "Enable UniPhier PH1-sLD8 SoC support"
  58         depends on ARCH_UNIPHIER_LD4_SLD8
  59         default y
  60
  61 config ARCH_UNIPHIER_PRO5
  62         bool "Enable UniPhier PH1-Pro5 SoC support"
  63         depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
  64         default y
  65
  66 config ARCH_UNIPHIER_PXS2
  67         bool "Enable UniPhier ProXstream2 SoC support"
  68         depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
  69         default y
  70
  71 config ARCH_UNIPHIER_LD6B
  72         bool "Enable UniPhier PH1-LD6b SoC support"
  73         depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
  74         default y
  75
  76 config CACHE_UNIPHIER
  77         bool "Enable the UniPhier L2 cache controller"
  78         depends on ARCH_UNIPHIER_32BIT
  79         select SYS_CACHE_SHIFT_7
  80         default y
  81         help
  82           This option allows to use the UniPhier System Cache as L2 cache.
  83
  84 config MICRO_SUPPORT_CARD
  85         bool "Use Micro Support Card"
  86         help
  87           This option provides support for the expansion board, available
  88           on some UniPhier reference boards.
  89
  90           Say Y to use the on-board UART, Ether, LED devices.
  91
  92 config CMD_PINMON
  93         bool "Enable boot mode pins monitor command"
  94         default y
  95         help
  96           The command "pinmon" shows the state of the boot mode pins.
  97           The boot mode pins are latched when the system reset is deasserted
  98           and determine which device the system should load a boot image from.
  99
 100 config CMD_DDRPHY_DUMP
 101         bool "Enable dump command of DDR PHY parameters"
 102         depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8
 103         default y
 104         help
 105           The command "ddrphy" shows the resulting parameters of DDR PHY
 106           training; it is useful for the evaluation of DDR PHY training.
 107
 108 config CMD_DDRMPHY_DUMP
 109         bool "Enable dump command of DDR Multi PHY parameters"
 110         depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
 111         default y
 112         help
 113           The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
 114           training; it is useful for the evaluation of DDR Multi PHY training.
 115
 116 endif