arch/arm/mach-uniphier/Kconfig

   1 if ARCH_UNIPHIER
   2
   3 config SYS_CONFIG_NAME
   4         default "uniphier"
   5
   6 config ARCH_UNIPHIER_32BIT
   7         bool
   8         select CPU_V7
   9         select CPU_V7_HAS_NONSEC
  10         select ARMV7_NONSEC
  11
  12 config ARCH_UNIPHIER_64BIT
  13         bool
  14         select ARM64
  15         select SPL_SEPARATE_BSS
  16         select ARMV8_MULTIENTRY
  17         select ARMV8_SPIN_TABLE
  18
  19 choice
  20         prompt "UniPhier SoC select"
  21         default ARCH_UNIPHIER_PRO4
  22
  23 config ARCH_UNIPHIER_SLD3
  24         bool "UniPhier PH1-sLD3 SoC"
  25         select ARCH_UNIPHIER_32BIT
  26
  27 config ARCH_UNIPHIER_LD4_SLD8
  28         bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
  29         select ARCH_UNIPHIER_32BIT
  30
  31 config ARCH_UNIPHIER_PRO4
  32         bool "UniPhier PH1-Pro4 SoC"
  33         select ARCH_UNIPHIER_32BIT
  34
  35 config ARCH_UNIPHIER_PRO5_PXS2_LD6B
  36         bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
  37         select ARCH_UNIPHIER_32BIT
  38
  39 config ARCH_UNIPHIER_LD11
  40         bool "UniPhier PH1-LD11 SoC"
  41         select ARCH_UNIPHIER_64BIT
  42
  43 config ARCH_UNIPHIER_LD20
  44         bool "UniPhier PH1-LD20 SoC"
  45         select ARCH_UNIPHIER_64BIT
  46         select OF_BOARD_SETUP
  47
  48 endchoice
  49
  50 config ARCH_UNIPHIER_LD4
  51         bool "Enable UniPhier PH1-LD4 SoC support"
  52         depends on ARCH_UNIPHIER_LD4_SLD8
  53         default y
  54
  55 config ARCH_UNIPHIER_SLD8
  56         bool "Enable UniPhier PH1-sLD8 SoC support"
  57         depends on ARCH_UNIPHIER_LD4_SLD8
  58         default y
  59
  60 config ARCH_UNIPHIER_PRO5
  61         bool "Enable UniPhier PH1-Pro5 SoC support"
  62         depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
  63         default y
  64
  65 config ARCH_UNIPHIER_PXS2
  66         bool "Enable UniPhier ProXstream2 SoC support"
  67         depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
  68         default y
  69
  70 config ARCH_UNIPHIER_LD6B
  71         bool "Enable UniPhier PH1-LD6b SoC support"
  72         depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
  73         default y
  74
  75 config CACHE_UNIPHIER
  76         bool "Enable the UniPhier L2 cache controller"
  77         depends on ARCH_UNIPHIER_32BIT
  78         select SYS_CACHE_SHIFT_7
  79         default y
  80         help
  81           This option allows to use the UniPhier System Cache as L2 cache.
  82
  83 config MICRO_SUPPORT_CARD
  84         bool "Use Micro Support Card"
  85         help
  86           This option provides support for the expansion board, available
  87           on some UniPhier reference boards.
  88
  89           Say Y to use the on-board UART, Ether, LED devices.
  90
  91 config CMD_PINMON
  92         bool "Enable boot mode pins monitor command"
  93         default y
  94         help
  95           The command "pinmon" shows the state of the boot mode pins.
  96           The boot mode pins are latched when the system reset is deasserted
  97           and determine which device the system should load a boot image from.
  98
  99 config CMD_DDRPHY_DUMP
 100         bool "Enable dump command of DDR PHY parameters"
 101         depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8
 102         default y
 103         help
 104           The command "ddrphy" shows the resulting parameters of DDR PHY
 105           training; it is useful for the evaluation of DDR PHY training.
 106
 107 config CMD_DDRMPHY_DUMP
 108         bool "Enable dump command of DDR Multi PHY parameters"
 109         depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
 110         default y
 111         help
 112           The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
 113           training; it is useful for the evaluation of DDR Multi PHY training.
 114
 115 endif