]> git.ipfire.org Git - thirdparty/linux.git/blob - arch/arm64/boot/dts/rockchip/rk3328-evb.dts
io_uring: reset -EBUSY error when io sq thread is waken up
[thirdparty/linux.git] / arch / arm64 / boot / dts / rockchip / rk3328-evb.dts
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2 /*
3 * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd
4 */
5
6 /dts-v1/;
7 #include "rk3328.dtsi"
8
9 / {
10 model = "Rockchip RK3328 EVB";
11 compatible = "rockchip,rk3328-evb", "rockchip,rk3328";
12
13 chosen {
14 stdout-path = "serial2:1500000n8";
15 };
16
17 dc_12v: dc-12v {
18 compatible = "regulator-fixed";
19 regulator-name = "dc_12v";
20 regulator-always-on;
21 regulator-boot-on;
22 regulator-min-microvolt = <12000000>;
23 regulator-max-microvolt = <12000000>;
24 };
25
26 sdio_pwrseq: sdio-pwrseq {
27 compatible = "mmc-pwrseq-simple";
28 pinctrl-names = "default";
29 pinctrl-0 = <&wifi_enable_h>;
30
31 /*
32 * On the module itself this is one of these (depending
33 * on the actual card populated):
34 * - SDIO_RESET_L_WL_REG_ON
35 * - PDN (power down when low)
36 */
37 reset-gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
38 };
39
40 vcc_sd: sdmmc-regulator {
41 compatible = "regulator-fixed";
42 gpio = <&gpio0 30 GPIO_ACTIVE_LOW>;
43 pinctrl-names = "default";
44 pinctrl-0 = <&sdmmc0m1_gpio>;
45 regulator-name = "vcc_sd";
46 regulator-min-microvolt = <3300000>;
47 regulator-max-microvolt = <3300000>;
48 vin-supply = <&vcc_io>;
49 };
50
51 vcc_sys: vcc-sys {
52 compatible = "regulator-fixed";
53 regulator-name = "vcc_sys";
54 regulator-always-on;
55 regulator-boot-on;
56 regulator-min-microvolt = <5000000>;
57 regulator-max-microvolt = <5000000>;
58 vin-supply = <&dc_12v>;
59 };
60
61 vcc_phy: vcc-phy-regulator {
62 compatible = "regulator-fixed";
63 regulator-name = "vcc_phy";
64 regulator-always-on;
65 regulator-boot-on;
66 };
67 };
68
69 &cpu0 {
70 cpu-supply = <&vdd_arm>;
71 };
72
73 &emmc {
74 bus-width = <8>;
75 cap-mmc-highspeed;
76 non-removable;
77 pinctrl-names = "default";
78 pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
79 status = "okay";
80 };
81
82 &gmac2phy {
83 phy-supply = <&vcc_phy>;
84 clock_in_out = "output";
85 assigned-clocks = <&cru SCLK_MAC2PHY_SRC>;
86 assigned-clock-rate = <50000000>;
87 assigned-clocks = <&cru SCLK_MAC2PHY>;
88 assigned-clock-parents = <&cru SCLK_MAC2PHY_SRC>;
89
90 };
91
92 &i2c1 {
93 status = "okay";
94
95 rk805: rk805@18 {
96 compatible = "rockchip,rk805";
97 reg = <0x18>;
98 interrupt-parent = <&gpio2>;
99 interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
100 #clock-cells = <1>;
101 clock-output-names = "xin32k", "rk805-clkout2";
102 gpio-controller;
103 #gpio-cells = <2>;
104 pinctrl-names = "default";
105 pinctrl-0 = <&pmic_int_l>;
106 rockchip,system-power-controller;
107 wakeup-source;
108
109 vcc1-supply = <&vcc_sys>;
110 vcc2-supply = <&vcc_sys>;
111 vcc3-supply = <&vcc_sys>;
112 vcc4-supply = <&vcc_sys>;
113 vcc5-supply = <&vcc_io>;
114 vcc6-supply = <&vcc_io>;
115
116 regulators {
117 vdd_logic: DCDC_REG1 {
118 regulator-name = "vdd_logic";
119 regulator-min-microvolt = <712500>;
120 regulator-max-microvolt = <1450000>;
121 regulator-always-on;
122 regulator-boot-on;
123 regulator-state-mem {
124 regulator-on-in-suspend;
125 regulator-suspend-microvolt = <1000000>;
126 };
127 };
128
129 vdd_arm: DCDC_REG2 {
130 regulator-name = "vdd_arm";
131 regulator-min-microvolt = <712500>;
132 regulator-max-microvolt = <1450000>;
133 regulator-always-on;
134 regulator-boot-on;
135 regulator-state-mem {
136 regulator-on-in-suspend;
137 regulator-suspend-microvolt = <950000>;
138 };
139 };
140
141 vcc_ddr: DCDC_REG3 {
142 regulator-name = "vcc_ddr";
143 regulator-always-on;
144 regulator-boot-on;
145 regulator-state-mem {
146 regulator-on-in-suspend;
147 };
148 };
149
150 vcc_io: DCDC_REG4 {
151 regulator-name = "vcc_io";
152 regulator-min-microvolt = <3300000>;
153 regulator-max-microvolt = <3300000>;
154 regulator-always-on;
155 regulator-boot-on;
156 regulator-state-mem {
157 regulator-on-in-suspend;
158 regulator-suspend-microvolt = <3300000>;
159 };
160 };
161
162 vcc_18: LDO_REG1 {
163 regulator-name = "vcc_18";
164 regulator-min-microvolt = <1800000>;
165 regulator-max-microvolt = <1800000>;
166 regulator-always-on;
167 regulator-boot-on;
168 regulator-state-mem {
169 regulator-on-in-suspend;
170 regulator-suspend-microvolt = <1800000>;
171 };
172 };
173
174 vcc18_emmc: LDO_REG2 {
175 regulator-name = "vcc18_emmc";
176 regulator-min-microvolt = <1800000>;
177 regulator-max-microvolt = <1800000>;
178 regulator-always-on;
179 regulator-boot-on;
180 regulator-state-mem {
181 regulator-on-in-suspend;
182 regulator-suspend-microvolt = <1800000>;
183 };
184 };
185
186 vdd_10: LDO_REG3 {
187 regulator-name = "vdd_10";
188 regulator-min-microvolt = <1000000>;
189 regulator-max-microvolt = <1000000>;
190 regulator-always-on;
191 regulator-boot-on;
192 regulator-state-mem {
193 regulator-on-in-suspend;
194 regulator-suspend-microvolt = <1000000>;
195 };
196 };
197 };
198 };
199 };
200
201 &pinctrl {
202 pmic {
203 pmic_int_l: pmic-int-l {
204 rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
205 };
206 };
207
208 sdio-pwrseq {
209 wifi_enable_h: wifi-enable-h {
210 rockchip,pins =
211 <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
212 };
213 };
214 };
215
216 &sdio {
217 bus-width = <4>;
218 cap-sd-highspeed;
219 cap-sdio-irq;
220 keep-power-in-suspend;
221 max-frequency = <150000000>;
222 mmc-pwrseq = <&sdio_pwrseq>;
223 non-removable;
224 pinctrl-names = "default";
225 pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
226 status = "okay";
227 };
228
229 &sdmmc {
230 bus-width = <4>;
231 cap-mmc-highspeed;
232 cap-sd-highspeed;
233 disable-wp;
234 max-frequency = <150000000>;
235 pinctrl-names = "default";
236 pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
237 vmmc-supply = <&vcc_sd>;
238 status = "okay";
239 };
240
241 &tsadc {
242 status = "okay";
243 };
244
245 &uart2 {
246 status = "okay";
247 };
248
249 &u2phy {
250 status = "okay";
251 };
252
253 &u2phy_host {
254 status = "okay";
255 };
256
257 &u2phy_otg {
258 status = "okay";
259 };
260
261 &usb20_otg {
262 status = "okay";
263 };
264
265 &usb_host0_ehci {
266 status = "okay";
267 };
268
269 &usb_host0_ohci {
270 status = "okay";
271 };