board/Marvell/openrd/kwbimage.cfg

   1 #
   2 # (C) Copyright 2009
   3 # Marvell Semiconductor <www.marvell.com>
   4 # Written-by: Prafulla Wadaskar <prafulla@marvell.com>
   5 #
   6 # SPDX-License-Identifier:      GPL-2.0+
   7 #
   8 # Refer doc/README.kwbimage for more details about how-to configure
   9 # and create kirkwood boot image
  10 #
  11
  12 # Boot Media configurations
  13 BOOT_FROM       nand
  14 NAND_ECC_MODE   default
  15 NAND_PAGE_SIZE  0x0800
  16
  17 # SOC registers configuration using bootrom header extension
  18 # Maximum KWBIMAGE_MAX_CONFIG configurations allowed
  19
  20 # Configure RGMII-0 interface pad voltage to 1.8V
  21 DATA 0xFFD100e0 0x1b1b1b9b
  22
  23 #Dram initalization for SINGLE x16 CL=5 @ 400MHz
  24 DATA 0xFFD01400 0x43000c30      # DDR Configuration register
  25 # bit13-0:  0xc30 (3120 DDR2 clks refresh rate)
  26 # bit23-14: zero
  27 # bit24: 1= enable exit self refresh mode on DDR access
  28 # bit25: 1 required
  29 # bit29-26: zero
  30 # bit31-30: 01
  31
  32 DATA 0xFFD01404 0x37543000      # DDR Controller Control Low
  33 # bit 4:    0=addr/cmd in smame cycle
  34 # bit 5:    0=clk is driven during self refresh, we don't care for APX
  35 # bit 6:    0=use recommended falling edge of clk for addr/cmd
  36 # bit14:    0=input buffer always powered up
  37 # bit18:    1=cpu lock transaction enabled
  38 # bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
  39 # bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
  40 # bit30-28: 3 required
  41 # bit31:    0=no additional STARTBURST delay
  42
  43 DATA 0xFFD01408 0x22125451      # DDR Timing (Low) (active cycles value +1)
  44 # bit3-0:   TRAS lsbs
  45 # bit7-4:   TRCD
  46 # bit11- 8: TRP
  47 # bit15-12: TWR
  48 # bit19-16: TWTR
  49 # bit20:    TRAS msb
  50 # bit23-21: 0x0
  51 # bit27-24: TRRD
  52 # bit31-28: TRTP
  53
  54 DATA 0xFFD0140C 0x00000a33      #  DDR Timing (High)
  55 # bit6-0:   TRFC
  56 # bit8-7:   TR2R
  57 # bit10-9:  TR2W
  58 # bit12-11: TW2W
  59 # bit31-13: zero required
  60
  61 DATA 0xFFD01410 0x000000cc      #  DDR Address Control
  62 # bit1-0:   00, Cs0width=x8
  63 # bit3-2:   11, Cs0size=1Gb
  64 # bit5-4:   00, Cs1width=x8
  65 # bit7-6:   11, Cs1size=1Gb
  66 # bit9-8:   00, Cs2width=nonexistent
  67 # bit11-10: 00, Cs2size =nonexistent
  68 # bit13-12: 00, Cs3width=nonexistent
  69 # bit15-14: 00, Cs3size =nonexistent
  70 # bit16:    0,  Cs0AddrSel
  71 # bit17:    0,  Cs1AddrSel
  72 # bit18:    0,  Cs2AddrSel
  73 # bit19:    0,  Cs3AddrSel
  74 # bit31-20: 0 required
  75
  76 DATA 0xFFD01414 0x00000000      #  DDR Open Pages Control
  77 # bit0:    0,  OpenPage enabled
  78 # bit31-1: 0 required
  79
  80 DATA 0xFFD01418 0x00000000      #  DDR Operation
  81 # bit3-0:   0x0, DDR cmd
  82 # bit31-4:  0 required
  83
  84 DATA 0xFFD0141C 0x00000C52      #  DDR Mode
  85 # bit2-0:   2, BurstLen=2 required
  86 # bit3:     0, BurstType=0 required
  87 # bit6-4:   4, CL=5
  88 # bit7:     0, TestMode=0 normal
  89 # bit8:     0, DLL reset=0 normal
  90 # bit11-9:  6, auto-precharge write recovery ????????????
  91 # bit12:    0, PD must be zero
  92 # bit31-13: 0 required
  93
  94 DATA 0xFFD01420 0x00000042      #  DDR Extended Mode
  95 # bit0:    0,  DDR DLL enabled
  96 # bit1:    1,  DDR drive strength reduced
  97 # bit2:    0,  DDR ODT control lsd (disabled)
  98 # bit5-3:  000, required
  99 # bit6:    1,  DDR ODT control msb, (disabled)
 100 # bit9-7:  000, required
 101 # bit10:   0,  differential DQS enabled
 102 # bit11:   0, required
 103 # bit12:   0, DDR output buffer enabled
 104 # bit31-13: 0 required
 105
 106 DATA 0xFFD01424 0x0000F17F      #  DDR Controller Control High
 107 # bit2-0:  111, required
 108 # bit3  :  1  , MBUS Burst Chop disabled
 109 # bit6-4:  111, required
 110 # bit7  :  0
 111 # bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
 112 # bit9  :  0  , no half clock cycle addition to dataout
 113 # bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
 114 # bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
 115 # bit15-12: 1111 required
 116 # bit31-16: 0    required
 117
 118 DATA 0xFFD01428 0x00085520      # DDR2 ODT Read Timing (default values)
 119 DATA 0xFFD0147C 0x00008552      # DDR2 ODT Write Timing (default values)
 120
 121 DATA 0xFFD01500 0x00000000      # CS[0]n Base address to 0x0
 122 DATA 0xFFD01504 0x0FFFFFF1      # CS[0]n Size
 123 # bit0:    1,  Window enabled
 124 # bit1:    0,  Write Protect disabled
 125 # bit3-2:  00, CS0 hit selected
 126 # bit23-4: ones, required
 127 # bit31-24: 0x0F, Size (i.e. 256MB)
 128
 129 DATA 0xFFD01508 0x10000000      # CS[1]n Base address to 256Mb
 130 DATA 0xFFD0150C 0x0FFFFFF5      # CS[1]n Size 256Mb Window enabled for CS1
 131
 132 DATA 0xFFD01514 0x00000000      # CS[2]n Size, window disabled
 133 DATA 0xFFD0151C 0x00000000      # CS[3]n Size, window disabled
 134
 135 DATA 0xFFD01494 0x00120012      #  DDR ODT Control (Low)
 136 # bit3-0:   0010, (read) M_ODT[0] is asserted during read from DRAM CS1
 137 # bit7-4:   0001, (read) M_ODT[1] is asserted during read from DRAM CS0
 138 # bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
 139 # bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
 140 DATA 0xFFD01498 0x00000000      #  DDR ODT Control (High)
 141
 142 DATA 0xFFD0149C 0x0000E40f      # CPU ODT Control
 143 # bit3-0:    1111, internal ODT is asserted during read from DRAM bank 0-3
 144 # bit11-10:    01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
 145 # bit13-12:    10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
 146 # bit14:        1, M_STARTBURST_IN ODT: Enabled
 147 # bit15:        1, DDR IO ODT Unit: Use ODT block
 148 DATA 0xFFD01480 0x00000001      # DDR Initialization Control
 149 #bit0=1, enable DDR init upon this register write
 150
 151 # End of Header extension
 152 DATA 0x0 0x0