3 * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
4 * Marius Groeger <mgroeger@sysgo.de>
7 * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
10 * Texas Instruments, <www.ti.com>
11 * Kshitij Gupta <Kshitij@ti.com>
15 * Philippe Robin, <philippe.robin@arm.com>
19 * Linus Walleij <linus.walleij@linaro.org>
21 * SPDX-License-Identifier: GPL-2.0+
26 #include "integrator-sc.h"
29 #define INTEGRATOR_BOOT_ROM_BASE 0x20000000
30 #define INTEGRATOR_HDR0_SDRAM_BASE 0x80000000
33 * These are in the physical addresses on the CPU side, i.e.
34 * where we read and write stuff - you don't want to try to
37 #define PHYS_PCI_MEM_BASE 0x40000000
38 #define PHYS_PCI_IO_BASE 0x60000000 /* PCI I/O space base */
39 #define PHYS_PCI_CONFIG_BASE 0x61000000
40 #define PHYS_PCI_V3_BASE 0x62000000 /* V360EPC registers */
41 #define SZ_256M 0x10000000
44 * These are in the PCI BUS address space
45 * Set to 0x00000000 in the Linux kernel, 0x40000000 in Boot monitor
46 * we follow the example of the kernel, because that is the address
47 * range that devices actually use - what would they be doing at
50 #define PCI_BUS_NONMEM_START 0x00000000
51 #define PCI_BUS_NONMEM_SIZE SZ_256M
53 #define PCI_BUS_PREMEM_START (PCI_BUS_NONMEM_START + PCI_BUS_NONMEM_SIZE)
54 #define PCI_BUS_PREMEM_SIZE SZ_256M
56 #if PCI_BUS_NONMEM_START & 0x000fffff
57 #error PCI_BUS_NONMEM_START must be megabyte aligned
59 #if PCI_BUS_PREMEM_START & 0x000fffff
60 #error PCI_BUS_PREMEM_START must be megabyte aligned
64 * Initialize PCI Devices, report devices found.
67 #ifndef CONFIG_PCI_PNP
68 #define PCI_ENET0_IOADDR 0x60000000 /* First card in PCI I/O space */
69 #define PCI_ENET0_MEMADDR 0x40000000 /* First card in PCI memory space */
70 static struct pci_config_table pci_integrator_config_table
[] = {
71 { PCI_ANY_ID
, PCI_ANY_ID
, PCI_ANY_ID
, PCI_ANY_ID
, 0x0f, PCI_ANY_ID
,
72 pci_cfgfunc_config_device
, { PCI_ENET0_IOADDR
,
74 PCI_COMMAND_MEMORY
| PCI_COMMAND_MASTER
}},
77 #endif /* CONFIG_PCI_PNP */
79 /* V3 access routines */
80 #define v3_writeb(o, v) __raw_writeb(v, PHYS_PCI_V3_BASE + (unsigned int)(o))
81 #define v3_readb(o) (__raw_readb(PHYS_PCI_V3_BASE + (unsigned int)(o)))
83 #define v3_writew(o, v) __raw_writew(v, PHYS_PCI_V3_BASE + (unsigned int)(o))
84 #define v3_readw(o) (__raw_readw(PHYS_PCI_V3_BASE + (unsigned int)(o)))
86 #define v3_writel(o, v) __raw_writel(v, PHYS_PCI_V3_BASE + (unsigned int)(o))
87 #define v3_readl(o) (__raw_readl(PHYS_PCI_V3_BASE + (unsigned int)(o)))
89 static unsigned long v3_open_config_window(pci_dev_t bdf
, int offset
)
91 unsigned int address
, mapaddress
;
92 unsigned int busnr
= PCI_BUS(bdf
);
93 unsigned int devfn
= PCI_FUNC(bdf
);
96 * Trap out illegal values
107 * Linux calls the thing U-Boot calls "DEV" "SLOT"
108 * instead, but it's the same 5 bits
110 int slot
= PCI_DEV(bdf
);
113 * local bus segment so need a type 0 config cycle
115 * build the PCI configuration "address" with one-hot in
119 * 3:1 = config cycle (101)
120 * 0 = PCI A1 & A0 are 0 (0)
122 address
= PCI_FUNC(bdf
) << 8;
123 mapaddress
= V3_LB_MAP_TYPE_CONFIG
;
127 * high order bits are handled by the MAP register
129 mapaddress
|= 1 << (slot
- 5);
132 * low order bits handled directly in the address
134 address
|= 1 << (slot
+ 11);
137 * not the local bus segment so need a type 1 config cycle
141 * 15:11 = slot number (7:3 of devfn)
142 * 10:8 = func number (2:0 of devfn)
145 * 3:1 = config cycle (101)
146 * 0 = PCI A1 & A0 from host bus (1)
148 mapaddress
= V3_LB_MAP_TYPE_CONFIG
| V3_LB_MAP_AD_LOW_EN
;
149 address
= (busnr
<< 16) | (devfn
<< 8);
153 * Set up base0 to see all 512Mbytes of memory space (not
154 * prefetchable), this frees up base1 for re-use by
155 * configuration memory
157 v3_writel(V3_LB_BASE0
, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE
) |
158 V3_LB_BASE_ADR_SIZE_512MB
| V3_LB_BASE_ENABLE
);
161 * Set up base1/map1 to point into configuration space.
163 v3_writel(V3_LB_BASE1
, v3_addr_to_lb_base(PHYS_PCI_CONFIG_BASE
) |
164 V3_LB_BASE_ADR_SIZE_16MB
| V3_LB_BASE_ENABLE
);
165 v3_writew(V3_LB_MAP1
, mapaddress
);
167 return PHYS_PCI_CONFIG_BASE
+ address
+ offset
;
170 static void v3_close_config_window(void)
173 * Reassign base1 for use by prefetchable PCI memory
175 v3_writel(V3_LB_BASE1
, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE
+ SZ_256M
) |
176 V3_LB_BASE_ADR_SIZE_256MB
| V3_LB_BASE_PREFETCH
|
178 v3_writew(V3_LB_MAP1
, v3_addr_to_lb_map(PCI_BUS_PREMEM_START
) |
179 V3_LB_MAP_TYPE_MEM_MULTIPLE
);
182 * And shrink base0 back to a 256M window (NOTE: MAP0 already correct)
184 v3_writel(V3_LB_BASE0
, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE
) |
185 V3_LB_BASE_ADR_SIZE_256MB
| V3_LB_BASE_ENABLE
);
188 static int pci_integrator_read_byte(struct pci_controller
*hose
, pci_dev_t bdf
,
189 int offset
, unsigned char *val
)
193 addr
= v3_open_config_window(bdf
, offset
);
194 *val
= __raw_readb(addr
);
195 v3_close_config_window();
199 static int pci_integrator_read__word(struct pci_controller
*hose
,
200 pci_dev_t bdf
, int offset
,
205 addr
= v3_open_config_window(bdf
, offset
);
206 *val
= __raw_readw(addr
);
207 v3_close_config_window();
211 static int pci_integrator_read_dword(struct pci_controller
*hose
,
212 pci_dev_t bdf
, int offset
,
217 addr
= v3_open_config_window(bdf
, offset
);
218 *val
= __raw_readl(addr
);
219 v3_close_config_window();
223 static int pci_integrator_write_byte(struct pci_controller
*hose
,
224 pci_dev_t bdf
, int offset
,
229 addr
= v3_open_config_window(bdf
, offset
);
230 __raw_writeb((u8
)val
, addr
);
232 v3_close_config_window();
236 static int pci_integrator_write_word(struct pci_controller
*hose
,
237 pci_dev_t bdf
, int offset
,
242 addr
= v3_open_config_window(bdf
, offset
);
243 __raw_writew((u8
)val
, addr
);
245 v3_close_config_window();
249 static int pci_integrator_write_dword(struct pci_controller
*hose
,
250 pci_dev_t bdf
, int offset
,
255 addr
= v3_open_config_window(bdf
, offset
);
256 __raw_writel((u8
)val
, addr
);
258 v3_close_config_window();
262 struct pci_controller integrator_hose
= {
263 #ifndef CONFIG_PCI_PNP
264 config_table
: pci_integrator_config_table
,
268 void pci_init_board(void)
270 struct pci_controller
*hose
= &integrator_hose
;
273 /* setting this register will take the V3 out of reset */
274 __raw_writel(SC_PCI_PCIEN
, SC_PCI
);
276 /* Wait for 230 ms (from spec) before accessing any V3 registers */
279 /* Now write the Base I/O Address Word to PHYS_PCI_V3_BASE + 0x6E */
280 v3_writew(V3_LB_IO_BASE
, (PHYS_PCI_V3_BASE
>> 16));
282 /* Wait for the mailbox to settle */
284 v3_writeb(V3_MAIL_DATA
, 0xAA);
285 v3_writeb(V3_MAIL_DATA
+ 4, 0x55);
286 } while (v3_readb(V3_MAIL_DATA
) != 0xAA ||
287 v3_readb(V3_MAIL_DATA
+ 4) != 0x55);
289 /* Make sure that V3 register access is not locked, if it is, unlock it */
290 if (v3_readw(V3_SYSTEM
) & V3_SYSTEM_M_LOCK
)
291 v3_writew(V3_SYSTEM
, 0xA05F);
294 * Ensure that the slave accesses from PCI are disabled while we
295 * setup memory windows
297 val
= v3_readw(V3_PCI_CMD
);
298 val
&= ~(V3_COMMAND_M_MEM_EN
| V3_COMMAND_M_IO_EN
);
299 v3_writew(V3_PCI_CMD
, val
);
301 /* Clear RST_OUT to 0; keep the PCI bus in reset until we've finished */
302 val
= v3_readw(V3_SYSTEM
);
303 val
&= ~V3_SYSTEM_M_RST_OUT
;
304 v3_writew(V3_SYSTEM
, val
);
306 /* Make all accesses from PCI space retry until we're ready for them */
307 val
= v3_readw(V3_PCI_CFG
);
308 val
|= V3_PCI_CFG_M_RETRY_EN
;
309 v3_writew(V3_PCI_CFG
, val
);
312 * Set up any V3 PCI Configuration Registers that we absolutely have to.
313 * LB_CFG controls Local Bus protocol.
314 * Enable LocalBus byte strobes for READ accesses too.
315 * set bit 7 BE_IMODE and bit 6 BE_OMODE
317 val
= v3_readw(V3_LB_CFG
);
319 v3_writew(V3_LB_CFG
, val
);
321 /* PCI_CMD controls overall PCI operation. Enable PCI bus master. */
322 val
= v3_readw(V3_PCI_CMD
);
323 val
|= V3_COMMAND_M_MASTER_EN
;
324 v3_writew(V3_PCI_CMD
, val
);
327 * PCI_MAP0 controls where the PCI to CPU memory window is on
330 v3_writel(V3_PCI_MAP0
,
331 (INTEGRATOR_BOOT_ROM_BASE
) | (V3_PCI_MAP_M_ADR_SIZE_512MB
|
332 V3_PCI_MAP_M_REG_EN
|
333 V3_PCI_MAP_M_ENABLE
));
335 /* PCI_BASE0 is the PCI address of the start of the window */
336 v3_writel(V3_PCI_BASE0
, INTEGRATOR_BOOT_ROM_BASE
);
338 /* PCI_MAP1 is LOCAL address of the start of the window */
339 v3_writel(V3_PCI_MAP1
,
340 (INTEGRATOR_HDR0_SDRAM_BASE
) | (V3_PCI_MAP_M_ADR_SIZE_1GB
|
341 V3_PCI_MAP_M_REG_EN
|
342 V3_PCI_MAP_M_ENABLE
));
344 /* PCI_BASE1 is the PCI address of the start of the window */
345 v3_writel(V3_PCI_BASE1
, INTEGRATOR_HDR0_SDRAM_BASE
);
348 * Set up memory the windows from local bus memory into PCI
349 * configuration, I/O and Memory regions.
350 * PCI I/O, LB_BASE2 and LB_MAP2 are used exclusively for this.
352 v3_writew(V3_LB_BASE2
,
353 v3_addr_to_lb_map(PHYS_PCI_IO_BASE
) | V3_LB_BASE_ENABLE
);
354 v3_writew(V3_LB_MAP2
, 0);
356 /* PCI Configuration, use LB_BASE1/LB_MAP1. */
359 * PCI Memory use LB_BASE0/LB_MAP0 and LB_BASE1/LB_MAP1
360 * Map first 256Mbytes as non-prefetchable via BASE0/MAP0
362 v3_writel(V3_LB_BASE0
, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE
) |
363 V3_LB_BASE_ADR_SIZE_256MB
| V3_LB_BASE_ENABLE
);
364 v3_writew(V3_LB_MAP0
,
365 v3_addr_to_lb_map(PCI_BUS_NONMEM_START
) | V3_LB_MAP_TYPE_MEM
);
367 /* Map second 256 Mbytes as prefetchable via BASE1/MAP1 */
368 v3_writel(V3_LB_BASE1
, v3_addr_to_lb_base(PHYS_PCI_MEM_BASE
+ SZ_256M
) |
369 V3_LB_BASE_ADR_SIZE_256MB
| V3_LB_BASE_PREFETCH
|
371 v3_writew(V3_LB_MAP1
, v3_addr_to_lb_map(PCI_BUS_PREMEM_START
) |
372 V3_LB_MAP_TYPE_MEM_MULTIPLE
);
374 /* Dump PCI to local address space mappings */
375 debug("LB_BASE0 = %08x\n", v3_readl(V3_LB_BASE0
));
376 debug("LB_MAP0 = %04x\n", v3_readw(V3_LB_MAP0
));
377 debug("LB_BASE1 = %08x\n", v3_readl(V3_LB_BASE1
));
378 debug("LB_MAP1 = %04x\n", v3_readw(V3_LB_MAP1
));
379 debug("LB_BASE2 = %04x\n", v3_readw(V3_LB_BASE2
));
380 debug("LB_MAP2 = %04x\n", v3_readw(V3_LB_MAP2
));
381 debug("LB_IO_BASE = %04x\n", v3_readw(V3_LB_IO_BASE
));
384 * Allow accesses to PCI Configuration space and set up A1, A0 for
385 * type 1 config cycles
387 val
= v3_readw(V3_PCI_CFG
);
388 val
&= ~(V3_PCI_CFG_M_RETRY_EN
| V3_PCI_CFG_M_AD_LOW1
);
389 val
|= V3_PCI_CFG_M_AD_LOW0
;
390 v3_writew(V3_PCI_CFG
, val
);
392 /* now we can allow incoming PCI MEMORY accesses */
393 val
= v3_readw(V3_PCI_CMD
);
394 val
|= V3_COMMAND_M_MEM_EN
;
395 v3_writew(V3_PCI_CMD
, val
);
398 * Set RST_OUT to take the PCI bus is out of reset, PCI devices can
401 val
= v3_readw(V3_SYSTEM
);
402 val
|= V3_SYSTEM_M_RST_OUT
;
403 v3_writew(V3_SYSTEM
, val
);
405 /* Lock the V3 system register so that no one else can play with it */
406 val
= v3_readw(V3_SYSTEM
);
407 val
|= V3_SYSTEM_M_LOCK
;
408 v3_writew(V3_SYSTEM
, val
);
411 * Configure and register the PCI hose
413 hose
->first_busno
= 0;
414 hose
->last_busno
= 0xff;
416 /* System memory space, window 0 256 MB non-prefetchable */
417 pci_set_region(hose
->regions
+ 0,
418 PCI_BUS_NONMEM_START
, PHYS_PCI_MEM_BASE
,
422 /* System memory space, window 1 256 MB prefetchable */
423 pci_set_region(hose
->regions
+ 1,
424 PCI_BUS_PREMEM_START
, PHYS_PCI_MEM_BASE
+ SZ_256M
,
427 PCI_REGION_PREFETCH
);
430 pci_set_region(hose
->regions
+ 2,
431 0x00000000, PHYS_PCI_IO_BASE
, 0x01000000,
434 /* PCI Memory - config space */
435 pci_set_region(hose
->regions
+ 3,
436 0x00000000, PHYS_PCI_CONFIG_BASE
, 0x01000000,
439 pci_set_region(hose
->regions
+ 4,
440 0x00000000, PHYS_PCI_V3_BASE
, 0x01000000,
443 hose
->region_count
= 5;
446 pci_integrator_read_byte
,
447 pci_integrator_read__word
,
448 pci_integrator_read_dword
,
449 pci_integrator_write_byte
,
450 pci_integrator_write_word
,
451 pci_integrator_write_dword
);
453 pci_register_hose(hose
);
455 pciauto_config_init(hose
);
456 pciauto_config_device(hose
, 0);
458 hose
->last_busno
= pci_hose_scan(hose
);