board/c2mon/pcmcia.c

   1 #include <common.h>
   2 #include <mpc8xx.h>
   3 #include <pcmcia.h>
   4
   5 #undef  CONFIG_PCMCIA
   6
   7 #if     defined(CONFIG_CMD_PCMCIA)
   8 #define CONFIG_PCMCIA
   9 #endif
  10
  11 #if defined(CONFIG_CMD_IDE) && defined(CONFIG_IDE_8xx_PCCARD)
  12 #define CONFIG_PCMCIA
  13 #endif
  14
  15 #ifdef  CONFIG_PCMCIA
  16
  17 #define PCMCIA_BOARD_MSG "C2MON"
  18
  19 static void cfg_ports (void)
  20 {
  21         volatile immap_t        *immap;
  22         volatile cpm8xx_t       *cp;
  23         ushort sreg;
  24
  25         immap = (immap_t *)CONFIG_SYS_IMMR;
  26         cp    = (cpm8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_cpm));
  27
  28         /*
  29         * Configure Port C for TPS2211 PC-Card Power-Interface Switch
  30         *
  31         * Switch off all voltages, assert shutdown
  32         */
  33         sreg = immap->im_ioport.iop_pcdat;
  34         sreg |=  (TPS2211_VPPD0 | TPS2211_VPPD1);       /* VAVPP => Hi-Z */
  35         sreg &= ~(TPS2211_VCCD0 | TPS2211_VCCD1);       /* 3V and 5V off */
  36         immap->im_ioport.iop_pcdat = sreg;
  37
  38         immap->im_ioport.iop_pcpar &= ~(TPS2211_OUTPUTS);
  39         immap->im_ioport.iop_pcdir |=   TPS2211_OUTPUTS;
  40
  41         debug ("Set Port C: PAR:     %04x DIR:     %04x DAT:     %04x\n",
  42                immap->im_ioport.iop_pcpar,
  43                immap->im_ioport.iop_pcdir,
  44                immap->im_ioport.iop_pcdat);
  45
  46         /*
  47         * Configure Port B for TPS2211 PC-Card Power-Interface Switch
  48         *
  49         * Over-Current Input only
  50         */
  51         cp->cp_pbpar &= ~(TPS2211_INPUTS);
  52         cp->cp_pbdir &= ~(TPS2211_INPUTS);
  53
  54         debug ("Set Port B: PAR: %08x DIR: %08x DAT: %08x\n",
  55                cp->cp_pbpar, cp->cp_pbdir, cp->cp_pbdat);
  56 }
  57
  58 int pcmcia_hardware_enable(int slot)
  59 {
  60         volatile immap_t        *immap;
  61         volatile cpm8xx_t       *cp;
  62         volatile pcmconf8xx_t   *pcmp;
  63         volatile sysconf8xx_t   *sysp;
  64         uint reg, pipr, mask;
  65         ushort sreg;
  66         int i;
  67
  68         debug ("hardware_enable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
  69
  70         udelay(10000);
  71
  72         immap = (immap_t *)CONFIG_SYS_IMMR;
  73         sysp  = (sysconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_siu_conf));
  74         pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
  75         cp    = (cpm8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_cpm));
  76
  77         /* Configure Ports for TPS2211A PC-Card Power-Interface Switch */
  78         cfg_ports ();
  79
  80         /*
  81         * Configure SIUMCR to enable PCMCIA port B
  82         * (VFLS[0:1] are not used for debugging, we connect FRZ# instead)
  83         */
  84         sysp->sc_siumcr &= ~SIUMCR_DBGC11;      /* set DBGC to 00 */
  85
  86         /* clear interrupt state, and disable interrupts */
  87         pcmp->pcmc_pscr =  PCMCIA_MASK(_slot_);
  88         pcmp->pcmc_per &= ~PCMCIA_MASK(_slot_);
  89
  90         /*
  91         * Disable interrupts, DMA, and PCMCIA buffers
  92         * (isolate the interface) and assert RESET signal
  93         */
  94         debug ("Disable PCMCIA buffers and assert RESET\n");
  95         reg  = 0;
  96         reg |= __MY_PCMCIA_GCRX_CXRESET;        /* active high */
  97         reg |= __MY_PCMCIA_GCRX_CXOE;           /* active low  */
  98         PCMCIA_PGCRX(_slot_) = reg;
  99         udelay(500);
 100
 101         /*
 102         * Make sure there is a card in the slot, then configure the interface.
 103         */
 104         udelay(10000);
 105         debug ("[%d] %s: PIPR(%p)=0x%x\n",
 106                __LINE__,__FUNCTION__,
 107                &(pcmp->pcmc_pipr),pcmp->pcmc_pipr);
 108         if (pcmp->pcmc_pipr & (0x18000000 >> (slot << 4))) {
 109                 printf ("   No Card found\n");
 110                 return (1);
 111         }
 112
 113         /*
 114         * Power On: Set VAVCC to 3.3V or 5V, set VAVPP to Hi-Z
 115         */
 116         mask = PCMCIA_VS1(slot) | PCMCIA_VS2(slot);
 117         pipr = pcmp->pcmc_pipr;
 118         debug ("PIPR: 0x%x ==> VS1=o%s, VS2=o%s\n",
 119                pipr,
 120                (reg&PCMCIA_VS1(slot))?"n":"ff",
 121                (reg&PCMCIA_VS2(slot))?"n":"ff");
 122
 123         sreg = immap->im_ioport.iop_pcdat;
 124         if ((pipr & mask) == mask) {
 125                 sreg |=  (TPS2211_VPPD0 | TPS2211_VPPD1 |       /* VAVPP => Hi-Z */
 126                                 TPS2211_VCCD1);                 /* 5V on        */
 127                 sreg &= ~(TPS2211_VCCD0);                       /* 3V off       */
 128                 puts (" 5.0V card found: ");
 129         } else {
 130                 sreg |=  (TPS2211_VPPD0 | TPS2211_VPPD1 |       /* VAVPP => Hi-Z */
 131                                 TPS2211_VCCD0);                 /* 3V on        */
 132                 sreg &= ~(TPS2211_VCCD1);                       /* 5V off       */
 133                 puts (" 3.3V card found: ");
 134         }
 135
 136         debug ("\nPC DAT: %04x -> 3.3V %s 5.0V %s\n",
 137                sreg,
 138                ( (sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) ? "on" : "off",
 139                (!(sreg & TPS2211_VCCD0) &&  (sreg & TPS2211_VCCD1)) ? "on" : "off"
 140               );
 141
 142         immap->im_ioport.iop_pcdat = sreg;
 143
 144         /*  Wait 500 ms; use this to check for over-current */
 145         for (i=0; i<5000; ++i) {
 146                 if ((cp->cp_pbdat & TPS2211_OC) == 0) {
 147                         printf ("   *** Overcurrent - Safety shutdown ***\n");
 148                         immap->im_ioport.iop_pcdat &= ~(TPS2211_VCCD0|TPS2211_VCCD1);
 149                         return (1);
 150                 }
 151                 udelay (100);
 152         }
 153
 154         debug ("Enable PCMCIA buffers and stop RESET\n");
 155         reg  =  PCMCIA_PGCRX(_slot_);
 156         reg &= ~__MY_PCMCIA_GCRX_CXRESET;       /* active high */
 157         reg &= ~__MY_PCMCIA_GCRX_CXOE;          /* active low  */
 158         PCMCIA_PGCRX(_slot_) = reg;
 159
 160         udelay(250000); /* some cards need >150 ms to come up :-( */
 161
 162         debug ("# hardware_enable done\n");
 163
 164         return (0);
 165 }
 166
 167
 168 #if defined(CONFIG_CMD_PCMCIA)
 169 int pcmcia_hardware_disable(int slot)
 170 {
 171         volatile immap_t        *immap;
 172         volatile cpm8xx_t       *cp;
 173         volatile pcmconf8xx_t   *pcmp;
 174         u_long reg;
 175
 176         debug ("hardware_disable: " PCMCIA_BOARD_MSG " Slot %c\n", 'A'+slot);
 177
 178         immap = (immap_t *)CONFIG_SYS_IMMR;
 179         pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
 180
 181         /* Configure PCMCIA General Control Register */
 182         debug ("Disable PCMCIA buffers and assert RESET\n");
 183         reg  = 0;
 184         reg |= __MY_PCMCIA_GCRX_CXRESET;        /* active high */
 185         reg |= __MY_PCMCIA_GCRX_CXOE;           /* active low  */
 186         PCMCIA_PGCRX(_slot_) = reg;
 187
 188         /* ALl voltages off / Hi-Z */
 189         immap->im_ioport.iop_pcdat |= (TPS2211_VPPD0 | TPS2211_VPPD1 |
 190                         TPS2211_VCCD0 | TPS2211_VCCD1 );
 191
 192         udelay(10000);
 193
 194         return (0);
 195 }
 196 #endif
 197
 198
 199 int pcmcia_voltage_set(int slot, int vcc, int vpp)
 200 {
 201         volatile immap_t        *immap;
 202         volatile cpm8xx_t       *cp;
 203         volatile pcmconf8xx_t   *pcmp;
 204         u_long reg;
 205         ushort sreg;
 206
 207         debug ("voltage_set: "
 208                         PCMCIA_BOARD_MSG
 209                         " Slot %c, Vcc=%d.%d, Vpp=%d.%d\n",
 210         'A'+slot, vcc/10, vcc%10, vpp/10, vcc%10);
 211
 212         immap = (immap_t *)CONFIG_SYS_IMMR;
 213         cp    = (cpm8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_cpm));
 214         pcmp  = (pcmconf8xx_t *)(&(((immap_t *)CONFIG_SYS_IMMR)->im_pcmcia));
 215         /*
 216         * Disable PCMCIA buffers (isolate the interface)
 217         * and assert RESET signal
 218         */
 219         debug ("Disable PCMCIA buffers and assert RESET\n");
 220         reg  = PCMCIA_PGCRX(_slot_);
 221         reg |= __MY_PCMCIA_GCRX_CXRESET;        /* active high */
 222         reg |= __MY_PCMCIA_GCRX_CXOE;           /* active low  */
 223         PCMCIA_PGCRX(_slot_) = reg;
 224         udelay(500);
 225
 226         /*
 227         * Configure Port C pins for
 228         * 5 Volts Enable and 3 Volts enable,
 229         * Turn all power pins to Hi-Z
 230         */
 231         debug ("PCMCIA power OFF\n");
 232         cfg_ports ();   /* Enables switch, but all in Hi-Z */
 233
 234         sreg  = immap->im_ioport.iop_pcdat;
 235         sreg |= TPS2211_VPPD0 | TPS2211_VPPD1;          /* VAVPP always Hi-Z */
 236
 237         switch(vcc) {
 238                 case  0:                        break;  /* Switch off           */
 239                 case 33: sreg |=  TPS2211_VCCD0;        /* Switch on 3.3V       */
 240                 sreg &= ~TPS2211_VCCD1;
 241                 break;
 242                 case 50: sreg &= ~TPS2211_VCCD0;        /* Switch on 5.0V       */
 243                 sreg |=  TPS2211_VCCD1;
 244                 break;
 245                 default:                        goto done;
 246         }
 247
 248         /* Checking supported voltages */
 249
 250         debug ("PIPR: 0x%x --> %s\n",
 251                pcmp->pcmc_pipr,
 252                (pcmp->pcmc_pipr & 0x00008000) ? "only 5 V" : "can do 3.3V");
 253
 254         immap->im_ioport.iop_pcdat = sreg;
 255
 256 #ifdef DEBUG
 257 {
 258         char *s;
 259
 260         if ((sreg & TPS2211_VCCD0) && !(sreg & TPS2211_VCCD1)) {
 261                 s = "at 3.3V";
 262         } else if (!(sreg & TPS2211_VCCD0) &&  (sreg & TPS2211_VCCD1)) {
 263                 s = "at 5.0V";
 264         } else {
 265                 s = "down";
 266         }
 267         printf ("PCMCIA powered %s\n", s);
 268 }
 269 #endif
 270
 271 done:
 272         debug ("Enable PCMCIA buffers and stop RESET\n");
 273         reg  =  PCMCIA_PGCRX(_slot_);
 274         reg &= ~__MY_PCMCIA_GCRX_CXRESET;       /* active high */
 275         reg &= ~__MY_PCMCIA_GCRX_CXOE;          /* active low  */
 276         PCMCIA_PGCRX(_slot_) = reg;
 277         udelay(500);
 278
 279         debug ("voltage_set: " PCMCIA_BOARD_MSG " Slot %c, DONE\n",
 280                slot+'A');
 281         return (0);
 282 }
 283
 284 #endif  /* CONFIG_PCMCIA */