board/freescale/mpc5121ads/mpc5121ads.c

   1 /*
   2  * (C) Copyright 2007-2009 DENX Software Engineering
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #include <common.h>
   8 #include <asm/bitops.h>
   9 #include <command.h>
  10 #include <asm/io.h>
  11 #include <asm/processor.h>
  12 #include <asm/mpc512x.h>
  13 #include <fdt_support.h>
  14 #ifdef CONFIG_MISC_INIT_R
  15 #include <i2c.h>
  16 #endif
  17 #include <net.h>
  18
  19 #include <linux/mtd/mtd.h>
  20 #include <linux/mtd/nand.h>
  21
  22 DECLARE_GLOBAL_DATA_PTR;
  23
  24 void __mpc5121_nfc_select_chip(struct mtd_info *mtd, int chip);
  25
  26 /* Active chip number set in board_nand_select_device() (mpc5121_nfc.c) */
  27 extern int mpc5121_nfc_chip;
  28
  29 /* Control chips select signal on MPC5121ADS board */
  30 void mpc5121_nfc_select_chip(struct mtd_info *mtd, int chip)
  31 {
  32         unsigned char *csreg = (u8 *)CONFIG_SYS_CPLD_BASE + 0x09;
  33         u8 v;
  34
  35         v = in_8(csreg);
  36         v |= 0x0F;
  37
  38         if (chip >= 0) {
  39                 __mpc5121_nfc_select_chip(mtd, 0);
  40                 v &= ~(1 << mpc5121_nfc_chip);
  41         } else {
  42                 __mpc5121_nfc_select_chip(mtd, -1);
  43         }
  44
  45         out_8(csreg, v);
  46 }
  47
  48 int board_early_init_f(void)
  49 {
  50         /*
  51          * Disable Boot NOR FLASH write protect - CPLD Reg 8 NOR FLASH Control
  52          *
  53          * Without this the flash identification routine fails, as it needs to issue
  54          * write commands in order to establish the device ID.
  55          */
  56
  57 #ifdef CONFIG_MPC5121ADS_REV2
  58         out_8((u8 *)(CONFIG_SYS_CPLD_BASE + 0x08), 0xC1);
  59 #else
  60         if (in_8((u8 *)(CONFIG_SYS_CPLD_BASE + 0x08)) & 0x04) {
  61                 out_8((u8 *)(CONFIG_SYS_CPLD_BASE + 0x08), 0xC1);
  62         } else {
  63                 /* running from Backup flash */
  64                 out_8((u8 *)(CONFIG_SYS_CPLD_BASE + 0x08), 0x32);
  65         }
  66 #endif
  67         return 0;
  68 }
  69
  70 int is_micron(void){
  71
  72         ushort brd_rev = *(vu_short *)(CONFIG_SYS_CPLD_BASE + 0x00);
  73         uchar macaddr[6];
  74         u32 brddate, macchk, ismicron;
  75
  76         /*
  77          * MAC address has serial number with date of manufacture
  78          * Boards made before Nov-08 #1180 use Micron memory;
  79          * 001e59 is the STx vendor #
  80          * Default is Elpida since it works for both but is slightly slower
  81          */
  82         ismicron = 0;
  83         if (brd_rev >= 0x0400 && eth_getenv_enetaddr("ethaddr", macaddr)) {
  84                 brddate = (macaddr[3] << 16) + (macaddr[4] << 8) + macaddr[5];
  85                 macchk = (macaddr[0] << 16) + (macaddr[1] << 8) + macaddr[2];
  86                 debug("brddate = %d\n\t", brddate);
  87
  88                 if (macchk == 0x001e59 && brddate <= 8111180)
  89                         ismicron = 1;
  90         } else if (brd_rev < 0x400) {
  91                 ismicron = 1;
  92         }
  93         debug("Using %s Memory settings\n\t",
  94                 ismicron ? "Micron" : "Elpida");
  95         return(ismicron);
  96 }
  97
  98 phys_size_t initdram(int board_type)
  99 {
 100         u32 msize = 0;
 101         /*
 102          * Elpida MDDRC and initialization settings are an alternative
 103          * to the Default Micron ones for all but the earliest Rev 4 boards
 104          */
 105         ddr512x_config_t elpida_mddrc_config = {
 106                 .ddr_sys_config   = CONFIG_SYS_MDDRC_SYS_CFG_ELPIDA,
 107                 .ddr_time_config0 = CONFIG_SYS_MDDRC_TIME_CFG0,
 108                 .ddr_time_config1 = CONFIG_SYS_MDDRC_TIME_CFG1_ELPIDA,
 109                 .ddr_time_config2 = CONFIG_SYS_MDDRC_TIME_CFG2_ELPIDA,
 110         };
 111
 112         u32 elpida_init_sequence[] = {
 113                 CONFIG_SYS_DDRCMD_NOP,
 114                 CONFIG_SYS_DDRCMD_NOP,
 115                 CONFIG_SYS_DDRCMD_NOP,
 116                 CONFIG_SYS_DDRCMD_NOP,
 117                 CONFIG_SYS_DDRCMD_NOP,
 118                 CONFIG_SYS_DDRCMD_NOP,
 119                 CONFIG_SYS_DDRCMD_NOP,
 120                 CONFIG_SYS_DDRCMD_NOP,
 121                 CONFIG_SYS_DDRCMD_NOP,
 122                 CONFIG_SYS_DDRCMD_NOP,
 123                 CONFIG_SYS_DDRCMD_PCHG_ALL,
 124                 CONFIG_SYS_DDRCMD_NOP,
 125                 CONFIG_SYS_DDRCMD_RFSH,
 126                 CONFIG_SYS_DDRCMD_NOP,
 127                 CONFIG_SYS_DDRCMD_RFSH,
 128                 CONFIG_SYS_DDRCMD_NOP,
 129                 CONFIG_SYS_DDRCMD_EM2,
 130                 CONFIG_SYS_DDRCMD_EM3,
 131                 CONFIG_SYS_DDRCMD_EN_DLL,
 132                 CONFIG_SYS_ELPIDA_RES_DLL,
 133                 CONFIG_SYS_DDRCMD_PCHG_ALL,
 134                 CONFIG_SYS_DDRCMD_RFSH,
 135                 CONFIG_SYS_DDRCMD_RFSH,
 136                 CONFIG_SYS_DDRCMD_RFSH,
 137                 CONFIG_SYS_ELPIDA_INIT_DEV_OP,
 138                 CONFIG_SYS_DDRCMD_NOP,
 139                 CONFIG_SYS_DDRCMD_NOP,
 140                 CONFIG_SYS_DDRCMD_NOP,
 141                 CONFIG_SYS_DDRCMD_NOP,
 142                 CONFIG_SYS_DDRCMD_NOP,
 143                 CONFIG_SYS_DDRCMD_NOP,
 144                 CONFIG_SYS_DDRCMD_NOP,
 145                 CONFIG_SYS_DDRCMD_NOP,
 146                 CONFIG_SYS_DDRCMD_NOP,
 147                 CONFIG_SYS_DDRCMD_NOP,
 148                 CONFIG_SYS_DDRCMD_OCD_DEFAULT,
 149                 CONFIG_SYS_ELPIDA_OCD_EXIT,
 150                 CONFIG_SYS_DDRCMD_NOP,
 151                 CONFIG_SYS_DDRCMD_NOP,
 152                 CONFIG_SYS_DDRCMD_NOP,
 153                 CONFIG_SYS_DDRCMD_NOP,
 154                 CONFIG_SYS_DDRCMD_NOP,
 155                 CONFIG_SYS_DDRCMD_NOP,
 156                 CONFIG_SYS_DDRCMD_NOP,
 157                 CONFIG_SYS_DDRCMD_NOP,
 158                 CONFIG_SYS_DDRCMD_NOP,
 159                 CONFIG_SYS_DDRCMD_NOP
 160         };
 161
 162         if (is_micron()) {
 163                 msize = fixed_sdram(NULL, NULL, 0);
 164         } else {
 165                 msize = fixed_sdram(&elpida_mddrc_config,
 166                                 elpida_init_sequence,
 167                                 sizeof(elpida_init_sequence)/sizeof(u32));
 168         }
 169
 170         return msize;
 171 }
 172
 173 int misc_init_r(void)
 174 {
 175         u8 tmp_val;
 176
 177         /* Using this for DIU init before the driver in linux takes over
 178          *  Enable the TFP410 Encoder (I2C address 0x38)
 179          */
 180
 181         i2c_set_bus_num(2);
 182         tmp_val = 0xBF;
 183         i2c_write(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
 184         /* Verify if enabled */
 185         tmp_val = 0;
 186         i2c_read(0x38, 0x08, 1, &tmp_val, sizeof(tmp_val));
 187         debug("DVI Encoder Read: 0x%02x\n", tmp_val);
 188
 189         tmp_val = 0x10;
 190         i2c_write(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
 191         /* Verify if enabled */
 192         tmp_val = 0;
 193         i2c_read(0x38, 0x0A, 1, &tmp_val, sizeof(tmp_val));
 194         debug("DVI Encoder Read: 0x%02x\n", tmp_val);
 195
 196         return 0;
 197 }
 198
 199 static  iopin_t ioregs_init[] = {
 200         /* FUNC1=FEC_RX_DV Sets Next 3 to FEC pads */
 201         {
 202                 offsetof(struct ioctrl512x, io_control_spdif_txclk), 3, 0,
 203                 IO_PIN_FMUX(1) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 204                 IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
 205         },
 206         /* Set highest Slew on 9 PATA pins */
 207         {
 208                 offsetof(struct ioctrl512x, io_control_pata_ce1), 9, 1,
 209                 IO_PIN_FMUX(0) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 210                 IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
 211         },
 212         /* FUNC1=FEC_COL Sets Next 15 to FEC pads */
 213         {
 214                 offsetof(struct ioctrl512x, io_control_psc0_0), 15, 0,
 215                 IO_PIN_FMUX(1) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 216                 IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
 217         },
 218         /* FUNC1=SPDIF_TXCLK */
 219         {
 220                 offsetof(struct ioctrl512x, io_control_lpc_cs1), 1, 0,
 221                 IO_PIN_FMUX(1) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 222                 IO_PIN_PUE(0) | IO_PIN_ST(1) | IO_PIN_DS(3)
 223         },
 224         /* FUNC2=SPDIF_TX and sets Next pin to SPDIF_RX */
 225         {
 226                 offsetof(struct ioctrl512x, io_control_i2c1_scl), 2, 0,
 227                 IO_PIN_FMUX(2) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 228                 IO_PIN_PUE(0) | IO_PIN_ST(1) | IO_PIN_DS(3)
 229         },
 230         /* FUNC2=DIU CLK */
 231         {
 232                 offsetof(struct ioctrl512x, io_control_psc6_0), 1, 0,
 233                 IO_PIN_FMUX(2) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 234                 IO_PIN_PUE(0) | IO_PIN_ST(1) | IO_PIN_DS(3)
 235         },
 236         /* FUNC2=DIU_HSYNC */
 237         {
 238                 offsetof(struct ioctrl512x, io_control_psc6_1), 1, 0,
 239                 IO_PIN_FMUX(2) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 240                 IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
 241         },
 242         /* FUNC2=DIUVSYNC Sets Next 26 to DIU Pads */
 243         {
 244                 offsetof(struct ioctrl512x, io_control_psc6_4), 26, 0,
 245                 IO_PIN_FMUX(2) | IO_PIN_HOLD(0) | IO_PIN_PUD(0) |
 246                 IO_PIN_PUE(0) | IO_PIN_ST(0) | IO_PIN_DS(3)
 247         }
 248 };
 249
 250 static  iopin_t rev2_silicon_pci_ioregs_init[] = {
 251         /* FUNC0=PCI Sets next 54 to PCI pads */
 252         {
 253                 offsetof(struct ioctrl512x, io_control_pci_ad31), 54, 0,
 254                 IO_PIN_FMUX(0) | IO_PIN_HOLD(0) | IO_PIN_DS(0)
 255         }
 256 };
 257
 258 int checkboard (void)
 259 {
 260         ushort brd_rev = *(vu_short *) (CONFIG_SYS_CPLD_BASE + 0x00);
 261         uchar cpld_rev = *(vu_char *) (CONFIG_SYS_CPLD_BASE + 0x02);
 262         volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
 263         u32 spridr = in_be32(&im->sysconf.spridr);
 264
 265         printf ("Board: MPC5121ADS rev. 0x%04x (CPLD rev. 0x%02x)\n",
 266                 brd_rev, cpld_rev);
 267
 268         /* initialize function mux & slew rate IO inter alia on IO Pins  */
 269         iopin_initialize(ioregs_init, ARRAY_SIZE(ioregs_init));
 270
 271         if (SVR_MJREV (spridr) >= 2)
 272                 iopin_initialize(rev2_silicon_pci_ioregs_init, 1);
 273
 274         return 0;
 275 }
 276
 277 #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
 278 int ft_board_setup(void *blob, bd_t *bd)
 279 {
 280         ft_cpu_setup(blob, bd);
 281
 282         return 0;
 283 }
 284 #endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */