board/samsung/odroid/odroid.c

   1 /*
   2  * Copyright (C) 2014 Samsung Electronics
   3  * Przemyslaw Marczak <p.marczak@samsung.com>
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #include <common.h>
   9 #include <asm/arch/pinmux.h>
  10 #include <asm/arch/power.h>
  11 #include <asm/arch/clock.h>
  12 #include <asm/arch/gpio.h>
  13 #include <asm/gpio.h>
  14 #include <asm/arch/cpu.h>
  15 #include <power/pmic.h>
  16 #include <power/max77686_pmic.h>
  17 #include <errno.h>
  18 #include <usb.h>
  19 #include <usb/s3c_udc.h>
  20 #include <samsung/misc.h>
  21 #include "setup.h"
  22
  23 DECLARE_GLOBAL_DATA_PTR;
  24
  25 #ifdef CONFIG_BOARD_TYPES
  26 /* Odroid board types */
  27 enum {
  28         ODROID_TYPE_U3,
  29         ODROID_TYPE_X2,
  30         ODROID_TYPES,
  31 };
  32
  33 void set_board_type(void)
  34 {
  35         /* Set GPA1 pin 1 to HI - enable XCL205 output */
  36         writel(XCL205_EN_GPIO_CON_CFG, XCL205_EN_GPIO_CON);
  37         writel(XCL205_EN_GPIO_DAT_CFG, XCL205_EN_GPIO_CON + 0x4);
  38         writel(XCL205_EN_GPIO_PUD_CFG, XCL205_EN_GPIO_CON + 0x8);
  39         writel(XCL205_EN_GPIO_DRV_CFG, XCL205_EN_GPIO_CON + 0xc);
  40
  41         /* Set GPC1 pin 2 to IN - check XCL205 output state */
  42         writel(XCL205_STATE_GPIO_CON_CFG, XCL205_STATE_GPIO_CON);
  43         writel(XCL205_STATE_GPIO_PUD_CFG, XCL205_STATE_GPIO_CON + 0x8);
  44
  45         /* XCL205 - needs some latch time */
  46         sdelay(200000);
  47
  48         /* Check GPC1 pin2 - LED supplied by XCL205 - X2 only */
  49         if (readl(XCL205_STATE_GPIO_DAT) & (1 << XCL205_STATE_GPIO_PIN))
  50                 gd->board_type = ODROID_TYPE_X2;
  51         else
  52                 gd->board_type = ODROID_TYPE_U3;
  53 }
  54
  55 const char *get_board_type(void)
  56 {
  57         const char *board_type[] = {"u3", "x2"};
  58
  59         return board_type[gd->board_type];
  60 }
  61 #endif
  62
  63 #ifdef CONFIG_SET_DFU_ALT_INFO
  64 char *get_dfu_alt_system(void)
  65 {
  66         return getenv("dfu_alt_system");
  67 }
  68
  69 char *get_dfu_alt_boot(void)
  70 {
  71         char *alt_boot;
  72
  73         switch (get_boot_mode()) {
  74         case BOOT_MODE_SD:
  75                 alt_boot = CONFIG_DFU_ALT_BOOT_SD;
  76                 break;
  77         case BOOT_MODE_EMMC:
  78         case BOOT_MODE_EMMC_SD:
  79                 alt_boot = CONFIG_DFU_ALT_BOOT_EMMC;
  80                 break;
  81         default:
  82                 alt_boot = NULL;
  83                 break;
  84         }
  85         return alt_boot;
  86 }
  87 #endif
  88
  89 static void board_clock_init(void)
  90 {
  91         unsigned int set, clr, clr_src_cpu, clr_pll_con0, clr_src_dmc;
  92         struct exynos4x12_clock *clk = (struct exynos4x12_clock *)
  93                                                 samsung_get_base_clock();
  94
  95         /*
  96          * CMU_CPU clocks src to MPLL
  97          * Bit values:                 0  ; 1
  98          * MUX_APLL_SEL:        FIN_PLL   ; FOUT_APLL
  99          * MUX_CORE_SEL:        MOUT_APLL ; SCLK_MPLL
 100          * MUX_HPM_SEL:         MOUT_APLL ; SCLK_MPLL_USER_C
 101          * MUX_MPLL_USER_SEL_C: FIN_PLL   ; SCLK_MPLL
 102         */
 103         clr_src_cpu = MUX_APLL_SEL(1) | MUX_CORE_SEL(1) |
 104                       MUX_HPM_SEL(1) | MUX_MPLL_USER_SEL_C(1);
 105         set = MUX_APLL_SEL(0) | MUX_CORE_SEL(1) | MUX_HPM_SEL(1) |
 106               MUX_MPLL_USER_SEL_C(1);
 107
 108         clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set);
 109
 110         /* Wait for mux change */
 111         while (readl(&clk->mux_stat_cpu) & MUX_STAT_CPU_CHANGING)
 112                 continue;
 113
 114         /* Set APLL to 1000MHz */
 115         clr_pll_con0 = SDIV(7) | PDIV(63) | MDIV(1023) | FSEL(1);
 116         set = SDIV(0) | PDIV(3) | MDIV(125) | FSEL(1);
 117
 118         clrsetbits_le32(&clk->apll_con0, clr_pll_con0, set);
 119
 120         /* Wait for PLL to be locked */
 121         while (!(readl(&clk->apll_con0) & PLL_LOCKED_BIT))
 122                 continue;
 123
 124         /* Set CMU_CPU clocks src to APLL */
 125         set = MUX_APLL_SEL(1) | MUX_CORE_SEL(0) | MUX_HPM_SEL(0) |
 126               MUX_MPLL_USER_SEL_C(1);
 127         clrsetbits_le32(&clk->src_cpu, clr_src_cpu, set);
 128
 129         /* Wait for mux change */
 130         while (readl(&clk->mux_stat_cpu) & MUX_STAT_CPU_CHANGING)
 131                 continue;
 132
 133         set = CORE_RATIO(0) | COREM0_RATIO(2) | COREM1_RATIO(5) |
 134               PERIPH_RATIO(0) | ATB_RATIO(4) | PCLK_DBG_RATIO(1) |
 135               APLL_RATIO(0) | CORE2_RATIO(0);
 136         /*
 137          * Set dividers for MOUTcore = 1000 MHz
 138          * coreout =      MOUT / (ratio + 1) = 1000 MHz (0)
 139          * corem0 =     armclk / (ratio + 1) = 333 MHz (2)
 140          * corem1 =     armclk / (ratio + 1) = 166 MHz (5)
 141          * periph =     armclk / (ratio + 1) = 1000 MHz (0)
 142          * atbout =       MOUT / (ratio + 1) = 200 MHz (4)
 143          * pclkdbgout = atbout / (ratio + 1) = 100 MHz (1)
 144          * sclkapll = MOUTapll / (ratio + 1) = 1000 MHz (0)
 145          * core2out = core_out / (ratio + 1) = 1000 MHz (0) (armclk)
 146         */
 147         clr = CORE_RATIO(7) | COREM0_RATIO(7) | COREM1_RATIO(7) |
 148               PERIPH_RATIO(7) | ATB_RATIO(7) | PCLK_DBG_RATIO(7) |
 149               APLL_RATIO(7) | CORE2_RATIO(7);
 150
 151         clrsetbits_le32(&clk->div_cpu0, clr, set);
 152
 153         /* Wait for divider ready status */
 154         while (readl(&clk->div_stat_cpu0) & DIV_STAT_CPU0_CHANGING)
 155                 continue;
 156
 157         /*
 158          * For MOUThpm = 1000 MHz (MOUTapll)
 159          * doutcopy = MOUThpm / (ratio + 1) = 200 (4)
 160          * sclkhpm = doutcopy / (ratio + 1) = 200 (4)
 161          * cores_out = armclk / (ratio + 1) = 200 (4)
 162          */
 163         clr = COPY_RATIO(7) | HPM_RATIO(7) | CORES_RATIO(7);
 164         set = COPY_RATIO(4) | HPM_RATIO(4) | CORES_RATIO(4);
 165
 166         clrsetbits_le32(&clk->div_cpu1, clr, set);
 167
 168         /* Wait for divider ready status */
 169         while (readl(&clk->div_stat_cpu1) & DIV_STAT_CPU1_CHANGING)
 170                 continue;
 171
 172         /*
 173          * Set CMU_DMC clocks src to APLL
 174          * Bit values:             0  ; 1
 175          * MUX_C2C_SEL:      SCLKMPLL ; SCLKAPLL
 176          * MUX_DMC_BUS_SEL:  SCLKMPLL ; SCLKAPLL
 177          * MUX_DPHY_SEL:     SCLKMPLL ; SCLKAPLL
 178          * MUX_MPLL_SEL:     FINPLL   ; MOUT_MPLL_FOUT
 179          * MUX_PWI_SEL:      0110 (MPLL); 0111 (EPLL); 1000 (VPLL); 0(XXTI)
 180          * MUX_G2D_ACP0_SEL: SCLKMPLL ; SCLKAPLL
 181          * MUX_G2D_ACP1_SEL: SCLKEPLL ; SCLKVPLL
 182          * MUX_G2D_ACP_SEL:  OUT_ACP0 ; OUT_ACP1
 183         */
 184         clr_src_dmc = MUX_C2C_SEL(1) | MUX_DMC_BUS_SEL(1) |
 185                       MUX_DPHY_SEL(1) | MUX_MPLL_SEL(1) |
 186                       MUX_PWI_SEL(15) | MUX_G2D_ACP0_SEL(1) |
 187                       MUX_G2D_ACP1_SEL(1) | MUX_G2D_ACP_SEL(1);
 188         set = MUX_C2C_SEL(1) | MUX_DMC_BUS_SEL(1) | MUX_DPHY_SEL(1) |
 189               MUX_MPLL_SEL(0) | MUX_PWI_SEL(0) | MUX_G2D_ACP0_SEL(1) |
 190               MUX_G2D_ACP1_SEL(1) | MUX_G2D_ACP_SEL(1);
 191
 192         clrsetbits_le32(&clk->src_dmc, clr_src_dmc, set);
 193
 194         /* Wait for mux change */
 195         while (readl(&clk->mux_stat_dmc) & MUX_STAT_DMC_CHANGING)
 196                 continue;
 197
 198         /* Set MPLL to 800MHz */
 199         set = SDIV(0) | PDIV(3) | MDIV(100) | FSEL(0) | PLL_ENABLE(1);
 200
 201         clrsetbits_le32(&clk->mpll_con0, clr_pll_con0, set);
 202
 203         /* Wait for PLL to be locked */
 204         while (!(readl(&clk->mpll_con0) & PLL_LOCKED_BIT))
 205                 continue;
 206
 207         /* Switch back CMU_DMC mux */
 208         set = MUX_C2C_SEL(0) | MUX_DMC_BUS_SEL(0) | MUX_DPHY_SEL(0) |
 209               MUX_MPLL_SEL(1) | MUX_PWI_SEL(8) | MUX_G2D_ACP0_SEL(0) |
 210               MUX_G2D_ACP1_SEL(0) | MUX_G2D_ACP_SEL(0);
 211
 212         clrsetbits_le32(&clk->src_dmc, clr_src_dmc, set);
 213
 214         /* Wait for mux change */
 215         while (readl(&clk->mux_stat_dmc) & MUX_STAT_DMC_CHANGING)
 216                 continue;
 217
 218         /* CLK_DIV_DMC0 */
 219         clr = ACP_RATIO(7) | ACP_PCLK_RATIO(7) | DPHY_RATIO(7) |
 220               DMC_RATIO(7) | DMCD_RATIO(7) | DMCP_RATIO(7);
 221         /*
 222          * For:
 223          * MOUTdmc = 800 MHz
 224          * MOUTdphy = 800 MHz
 225          *
 226          * aclk_acp = MOUTdmc / (ratio + 1) = 200 (3)
 227          * pclk_acp = aclk_acp / (ratio + 1) = 100 (1)
 228          * sclk_dphy = MOUTdphy / (ratio + 1) = 400 (1)
 229          * sclk_dmc = MOUTdmc / (ratio + 1) = 400 (1)
 230          * aclk_dmcd = sclk_dmc / (ratio + 1) = 200 (1)
 231          * aclk_dmcp = aclk_dmcd / (ratio + 1) = 100 (1)
 232          */
 233         set = ACP_RATIO(3) | ACP_PCLK_RATIO(1) | DPHY_RATIO(1) |
 234               DMC_RATIO(1) | DMCD_RATIO(1) | DMCP_RATIO(1);
 235
 236         clrsetbits_le32(&clk->div_dmc0, clr, set);
 237
 238         /* Wait for divider ready status */
 239         while (readl(&clk->div_stat_dmc0) & DIV_STAT_DMC0_CHANGING)
 240                 continue;
 241
 242         /* CLK_DIV_DMC1 */
 243         clr = G2D_ACP_RATIO(15) | C2C_RATIO(7) | PWI_RATIO(15) |
 244               C2C_ACLK_RATIO(7) | DVSEM_RATIO(127) | DPM_RATIO(127);
 245         /*
 246          * For:
 247          * MOUTg2d = 800 MHz
 248          * MOUTc2c = 800 Mhz
 249          * MOUTpwi = 108 MHz
 250          *
 251          * sclk_g2d_acp = MOUTg2d / (ratio + 1) = 200 (3)
 252          * sclk_c2c = MOUTc2c / (ratio + 1) = 400 (1)
 253          * aclk_c2c = sclk_c2c / (ratio + 1) = 200 (1)
 254          * sclk_pwi = MOUTpwi / (ratio + 1) = 18 (5)
 255          */
 256         set = G2D_ACP_RATIO(3) | C2C_RATIO(1) | PWI_RATIO(5) |
 257               C2C_ACLK_RATIO(1) | DVSEM_RATIO(1) | DPM_RATIO(1);
 258
 259         clrsetbits_le32(&clk->div_dmc1, clr, set);
 260
 261         /* Wait for divider ready status */
 262         while (readl(&clk->div_stat_dmc1) & DIV_STAT_DMC1_CHANGING)
 263                 continue;
 264
 265         /* CLK_SRC_PERIL0 */
 266         clr = UART0_SEL(15) | UART1_SEL(15) | UART2_SEL(15) |
 267               UART3_SEL(15) | UART4_SEL(15);
 268         /*
 269          * Set CLK_SRC_PERIL0 clocks src to MPLL
 270          * src values: 0(XXTI); 1(XusbXTI); 2(SCLK_HDMI24M); 3(SCLK_USBPHY0);
 271          *             5(SCLK_HDMIPHY); 6(SCLK_MPLL_USER_T); 7(SCLK_EPLL);
 272          *             8(SCLK_VPLL)
 273          *
 274          * Set all to SCLK_MPLL_USER_T
 275          */
 276         set = UART0_SEL(6) | UART1_SEL(6) | UART2_SEL(6) | UART3_SEL(6) |
 277               UART4_SEL(6);
 278
 279         clrsetbits_le32(&clk->src_peril0, clr, set);
 280
 281         /* CLK_DIV_PERIL0 */
 282         clr = UART0_RATIO(15) | UART1_RATIO(15) | UART2_RATIO(15) |
 283               UART3_RATIO(15) | UART4_RATIO(15);
 284         /*
 285          * For MOUTuart0-4: 800MHz
 286          *
 287          * SCLK_UARTx = MOUTuartX / (ratio + 1) = 100 (7)
 288         */
 289         set = UART0_RATIO(7) | UART1_RATIO(7) | UART2_RATIO(7) |
 290               UART3_RATIO(7) | UART4_RATIO(7);
 291
 292         clrsetbits_le32(&clk->div_peril0, clr, set);
 293
 294         while (readl(&clk->div_stat_peril0) & DIV_STAT_PERIL0_CHANGING)
 295                 continue;
 296
 297         /* CLK_DIV_FSYS1 */
 298         clr = MMC0_RATIO(15) | MMC0_PRE_RATIO(255) | MMC1_RATIO(15) |
 299               MMC1_PRE_RATIO(255);
 300         /*
 301          * For MOUTmmc0-3 = 800 MHz (MPLL)
 302          *
 303          * DOUTmmc1 = MOUTmmc1 / (ratio + 1) = 100 (7)
 304          * sclk_mmc1 = DOUTmmc1 / (ratio + 1) = 50 (1)
 305          * DOUTmmc0 = MOUTmmc0 / (ratio + 1) = 100 (7)
 306          * sclk_mmc0 = DOUTmmc0 / (ratio + 1) = 50 (1)
 307         */
 308         set = MMC0_RATIO(7) | MMC0_PRE_RATIO(1) | MMC1_RATIO(7) |
 309               MMC1_PRE_RATIO(1);
 310
 311         clrsetbits_le32(&clk->div_fsys1, clr, set);
 312
 313         /* Wait for divider ready status */
 314         while (readl(&clk->div_stat_fsys1) & DIV_STAT_FSYS1_CHANGING)
 315                 continue;
 316
 317         /* CLK_DIV_FSYS2 */
 318         clr = MMC2_RATIO(15) | MMC2_PRE_RATIO(255) | MMC3_RATIO(15) |
 319               MMC3_PRE_RATIO(255);
 320         /*
 321          * For MOUTmmc0-3 = 800 MHz (MPLL)
 322          *
 323          * DOUTmmc3 = MOUTmmc3 / (ratio + 1) = 100 (7)
 324          * sclk_mmc3 = DOUTmmc3 / (ratio + 1) = 50 (1)
 325          * DOUTmmc2 = MOUTmmc2 / (ratio + 1) = 100 (7)
 326          * sclk_mmc2 = DOUTmmc2 / (ratio + 1) = 50 (1)
 327         */
 328         set = MMC2_RATIO(7) | MMC2_PRE_RATIO(1) | MMC3_RATIO(7) |
 329               MMC3_PRE_RATIO(1);
 330
 331         clrsetbits_le32(&clk->div_fsys2, clr, set);
 332
 333         /* Wait for divider ready status */
 334         while (readl(&clk->div_stat_fsys2) & DIV_STAT_FSYS2_CHANGING)
 335                 continue;
 336
 337         /* CLK_DIV_FSYS3 */
 338         clr = MMC4_RATIO(15) | MMC4_PRE_RATIO(255);
 339         /*
 340          * For MOUTmmc4 = 800 MHz (MPLL)
 341          *
 342          * DOUTmmc4 = MOUTmmc4 / (ratio + 1) = 100 (7)
 343          * sclk_mmc4 = DOUTmmc4 / (ratio + 1) = 100 (0)
 344         */
 345         set = MMC4_RATIO(7) | MMC4_PRE_RATIO(0);
 346
 347         clrsetbits_le32(&clk->div_fsys3, clr, set);
 348
 349         /* Wait for divider ready status */
 350         while (readl(&clk->div_stat_fsys3) & DIV_STAT_FSYS3_CHANGING)
 351                 continue;
 352
 353         return;
 354 }
 355
 356 static void board_gpio_init(void)
 357 {
 358         /* eMMC Reset Pin */
 359         gpio_request(EXYNOS4X12_GPIO_K12, "eMMC Reset");
 360
 361         gpio_cfg_pin(EXYNOS4X12_GPIO_K12, S5P_GPIO_FUNC(0x1));
 362         gpio_set_pull(EXYNOS4X12_GPIO_K12, S5P_GPIO_PULL_NONE);
 363         gpio_set_drv(EXYNOS4X12_GPIO_K12, S5P_GPIO_DRV_4X);
 364
 365         /* Enable FAN (Odroid U3) */
 366         gpio_request(EXYNOS4X12_GPIO_D00, "FAN Control");
 367
 368         gpio_set_pull(EXYNOS4X12_GPIO_D00, S5P_GPIO_PULL_UP);
 369         gpio_set_drv(EXYNOS4X12_GPIO_D00, S5P_GPIO_DRV_4X);
 370         gpio_direction_output(EXYNOS4X12_GPIO_D00, 1);
 371
 372         /* OTG Vbus output (Odroid U3+) */
 373         gpio_request(EXYNOS4X12_GPIO_L20, "OTG Vbus");
 374
 375         gpio_set_pull(EXYNOS4X12_GPIO_L20, S5P_GPIO_PULL_NONE);
 376         gpio_set_drv(EXYNOS4X12_GPIO_L20, S5P_GPIO_DRV_4X);
 377         gpio_direction_output(EXYNOS4X12_GPIO_L20, 0);
 378
 379         /* OTG INT (Odroid U3+) */
 380         gpio_request(EXYNOS4X12_GPIO_X31, "OTG INT");
 381
 382         gpio_set_pull(EXYNOS4X12_GPIO_X31, S5P_GPIO_PULL_UP);
 383         gpio_set_drv(EXYNOS4X12_GPIO_X31, S5P_GPIO_DRV_4X);
 384         gpio_direction_input(EXYNOS4X12_GPIO_X31);
 385
 386         /* Blue LED (Odroid X2/U2/U3) */
 387         gpio_request(EXYNOS4X12_GPIO_C10, "Blue LED");
 388
 389         gpio_direction_output(EXYNOS4X12_GPIO_C10, 0);
 390
 391 #ifdef CONFIG_CMD_USB
 392         /* USB3503A Reference frequency */
 393         gpio_request(EXYNOS4X12_GPIO_X30, "USB3503A RefFreq");
 394
 395         /* USB3503A Connect */
 396         gpio_request(EXYNOS4X12_GPIO_X34, "USB3503A Connect");
 397
 398         /* USB3503A Reset */
 399         gpio_request(EXYNOS4X12_GPIO_X35, "USB3503A Reset");
 400 #endif
 401 }
 402
 403 static int pmic_init_max77686(void)
 404 {
 405         struct pmic *p = pmic_get("MAX77686_PMIC");
 406
 407         if (pmic_probe(p))
 408                 return -ENODEV;
 409
 410         /* Set LDO Voltage */
 411         max77686_set_ldo_voltage(p, 20, 1800000);       /* LDO20 eMMC */
 412         max77686_set_ldo_voltage(p, 21, 2800000);       /* LDO21 SD */
 413         max77686_set_ldo_voltage(p, 22, 2800000);       /* LDO22 eMMC */
 414
 415         return 0;
 416 }
 417
 418 int exynos_early_init_f(void)
 419 {
 420         board_clock_init();
 421
 422         return 0;
 423 }
 424
 425 int exynos_init(void)
 426 {
 427         /* The last MB of memory is reserved for secure firmware */
 428         gd->ram_size -= SZ_1M;
 429         gd->bd->bi_dram[CONFIG_NR_DRAM_BANKS - 1].size -= SZ_1M;
 430
 431         board_gpio_init();
 432
 433         return 0;
 434 }
 435
 436 int exynos_power_init(void)
 437 {
 438         pmic_init(0);
 439         pmic_init_max77686();
 440
 441         return 0;
 442 }
 443
 444 #ifdef CONFIG_USB_GADGET
 445 static int s5pc210_phy_control(int on)
 446 {
 447         struct pmic *p_pmic;
 448
 449         p_pmic = pmic_get("MAX77686_PMIC");
 450         if (!p_pmic)
 451                 return -ENODEV;
 452
 453         if (pmic_probe(p_pmic))
 454                 return -1;
 455
 456         if (on)
 457                 return max77686_set_ldo_mode(p_pmic, 12, OPMODE_ON);
 458         else
 459                 return max77686_set_ldo_mode(p_pmic, 12, OPMODE_LPM);
 460 }
 461
 462 struct s3c_plat_otg_data s5pc210_otg_data = {
 463         .phy_control    = s5pc210_phy_control,
 464         .regs_phy       = EXYNOS4X12_USBPHY_BASE,
 465         .regs_otg       = EXYNOS4X12_USBOTG_BASE,
 466         .usb_phy_ctrl   = EXYNOS4X12_USBPHY_CONTROL,
 467         .usb_flags      = PHY0_SLEEP,
 468 };
 469 #endif
 470
 471 #if defined(CONFIG_USB_GADGET) || defined(CONFIG_CMD_USB)
 472
 473 int board_usb_init(int index, enum usb_init_type init)
 474 {
 475 #ifdef CONFIG_CMD_USB
 476         struct pmic *p_pmic;
 477
 478         /* Set Ref freq 0 => 24MHz, 1 => 26MHz*/
 479         /* Odroid Us have it at 24MHz, Odroid Xs at 26MHz */
 480         if (gd->board_type == ODROID_TYPE_U3)
 481                 gpio_direction_output(EXYNOS4X12_GPIO_X30, 0);
 482         else
 483                 gpio_direction_output(EXYNOS4X12_GPIO_X30, 1);
 484
 485         /* Disconnect, Reset, Connect */
 486         gpio_direction_output(EXYNOS4X12_GPIO_X34, 0);
 487         gpio_direction_output(EXYNOS4X12_GPIO_X35, 0);
 488         gpio_direction_output(EXYNOS4X12_GPIO_X35, 1);
 489         gpio_direction_output(EXYNOS4X12_GPIO_X34, 1);
 490
 491         /* Power off and on BUCK8 for LAN9730 */
 492         debug("LAN9730 - Turning power buck 8 OFF and ON.\n");
 493
 494         p_pmic = pmic_get("MAX77686_PMIC");
 495         if (p_pmic && !pmic_probe(p_pmic)) {
 496                 max77686_set_buck_voltage(p_pmic, 8, 750000);
 497                 max77686_set_buck_voltage(p_pmic, 8, 3300000);
 498         }
 499
 500 #endif
 501
 502         debug("USB_udc_probe\n");
 503         return s3c_udc_probe(&s5pc210_otg_data);
 504 }
 505 #endif