board/sbc8641d/ddr.c

   1 /*
   2  * Copyright 2008 Freescale Semiconductor, Inc.
   3  *
   4  * This program is free software; you can redistribute it and/or
   5  * modify it under the terms of the GNU General Public License
   6  * Version 2 as published by the Free Software Foundation.
   7  */
   8
   9 #include <common.h>
  10 #include <i2c.h>
  11
  12 #include <asm/fsl_ddr_sdram.h>
  13 #include <asm/fsl_ddr_dimm_params.h>
  14
  15 static void
  16 get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
  17 {
  18         i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr2_spd_eeprom_t));
  19 }
  20
  21 unsigned int fsl_ddr_get_mem_data_rate(void)
  22 {
  23         return get_bus_freq(0);
  24 }
  25
  26 void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
  27                       unsigned int ctrl_num)
  28 {
  29         unsigned int i;
  30         unsigned int i2c_address = 0;
  31
  32         for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
  33                 if (ctrl_num == 0 && i == 0) {
  34                         i2c_address = SPD_EEPROM_ADDRESS1;
  35                 }
  36                 if (ctrl_num == 0 && i == 1) {
  37                         i2c_address = SPD_EEPROM_ADDRESS2;
  38                 }
  39                 if (ctrl_num == 1 && i == 0) {
  40                         i2c_address = SPD_EEPROM_ADDRESS3;
  41                 }
  42                 if (ctrl_num == 1 && i == 1) {
  43                         i2c_address = SPD_EEPROM_ADDRESS4;
  44                 }
  45                 get_spd(&(ctrl_dimms_spd[i]), i2c_address);
  46         }
  47 }
  48
  49 void fsl_ddr_board_options(memctl_options_t *popts,
  50                                 dimm_params_t *pdimm,
  51                                 unsigned int ctrl_num)
  52 {
  53         /*
  54          * Factors to consider for clock adjust:
  55          *      - number of chips on bus
  56          *      - position of slot
  57          *      - DDR1 vs. DDR2?
  58          *      - ???
  59          *
  60          * This needs to be determined on a board-by-board basis.
  61          *      0110    3/4 cycle late
  62          *      0111    7/8 cycle late
  63          */
  64         popts->clk_adjust = 7;
  65
  66         /*
  67          * Factors to consider for CPO:
  68          *      - frequency
  69          *      - ddr1 vs. ddr2
  70          */
  71         popts->cpo_override = 10;
  72
  73         /*
  74          * Factors to consider for write data delay:
  75          *      - number of DIMMs
  76          *
  77          * 1 = 1/4 clock delay
  78          * 2 = 1/2 clock delay
  79          * 3 = 3/4 clock delay
  80          * 4 = 1   clock delay
  81          * 5 = 5/4 clock delay
  82          * 6 = 3/2 clock delay
  83          */
  84         popts->write_data_delay = 3;
  85
  86         /*
  87          * Factors to consider for half-strength driver enable:
  88          *      - number of DIMMs installed
  89          */
  90         popts->half_strength_driver_enable = 0;
  91 }