board/sunxi/Kconfig

   1 if ARCH_SUNXI
   2
   3 choice
   4         prompt "Sunxi SoC Variant"
   5
   6 config MACH_SUN4I
   7         bool "sun4i (Allwinner A10)"
   8         select CPU_V7
   9         select SUPPORT_SPL
  10
  11 config MACH_SUN5I
  12         bool "sun5i (Allwinner A13)"
  13         select CPU_V7
  14         select SUPPORT_SPL
  15
  16 config MACH_SUN6I
  17         bool "sun6i (Allwinner A31)"
  18         select CPU_V7
  19         select SUPPORT_SPL
  20
  21 config MACH_SUN7I
  22         bool "sun7i (Allwinner A20)"
  23         select CPU_V7
  24         select CPU_V7_HAS_NONSEC
  25         select CPU_V7_HAS_VIRT
  26         select SUPPORT_SPL
  27         select ARMV7_BOOT_SEC_DEFAULT if OLD_SUNXI_KERNEL_COMPAT
  28
  29 config MACH_SUN8I
  30         bool "sun8i (Allwinner A23)"
  31         select CPU_V7
  32         select SUPPORT_SPL
  33
  34 endchoice
  35
  36 if MACH_SUN6I || MACH_SUN8I
  37
  38 config DRAM_CLK
  39         int "sun6i dram clock speed"
  40         default 312
  41         ---help---
  42         Set the dram clock speed, valid range 240 - 480, must be a multiple
  43         of 24.
  44
  45 config DRAM_ZQ
  46         int "sun6i dram zq value"
  47         default 123
  48         ---help---
  49         Set the dram zq value.
  50
  51 endif
  52
  53 config SYS_CONFIG_NAME
  54         default "sun4i" if MACH_SUN4I
  55         default "sun5i" if MACH_SUN5I
  56         default "sun6i" if MACH_SUN6I
  57         default "sun7i" if MACH_SUN7I
  58         default "sun8i" if MACH_SUN8I
  59
  60 choice
  61         prompt "Board"
  62
  63 config TARGET_A10_OLINUXINO_L
  64         bool "A10_OLINUXINO_L"
  65         depends on MACH_SUN4I
  66
  67 config TARGET_A10S_OLINUXINO_M
  68         bool "A10S_OLINUXINO_M"
  69         depends on MACH_SUN5I
  70
  71 config TARGET_A13_OLINUXINOM
  72         bool "A13_OLINUXINOM"
  73         depends on MACH_SUN5I
  74
  75 config TARGET_A13_OLINUXINO
  76         bool "A13_OLINUXINO"
  77         depends on MACH_SUN5I
  78
  79 config TARGET_A20_OLINUXINO_L2
  80         bool "A20_OLINUXINO_L2"
  81         depends on MACH_SUN7I
  82
  83 config TARGET_A20_OLINUXINO_L
  84         bool "A20_OLINUXINO_L"
  85         depends on MACH_SUN7I
  86
  87 config TARGET_A20_OLINUXINO_M
  88         bool "A20_OLINUXINO_M"
  89         depends on MACH_SUN7I
  90
  91 config TARGET_AUXTEK_T004
  92         bool "AUXTEK_T004"
  93         depends on MACH_SUN5I
  94
  95 config TARGET_BANANAPI
  96         bool "BANANAPI"
  97         depends on MACH_SUN7I
  98
  99 config TARGET_COLOMBUS
 100         bool "COLOMBUS"
 101         depends on MACH_SUN6I
 102
 103 config TARGET_CUBIEBOARD2
 104         bool "CUBIEBOARD2"
 105         depends on MACH_SUN7I
 106
 107 config TARGET_CUBIEBOARD
 108         bool "CUBIEBOARD"
 109         depends on MACH_SUN4I
 110
 111 config TARGET_CUBIETRUCK
 112         bool "CUBIETRUCK"
 113         depends on MACH_SUN7I
 114
 115 config TARGET_HUMMINGBIRD_A31
 116         bool "HUMMINGBIRD_A31"
 117         depends on MACH_SUN6I
 118
 119 config TARGET_IPPO_Q8H_V5
 120         bool "IPPO_Q8H_V5"
 121         depends on MACH_SUN8I
 122
 123 config TARGET_PCDUINO3
 124         bool "PCDUINO3"
 125         depends on MACH_SUN7I
 126
 127 config TARGET_MELE_A1000G
 128         bool "MELE_A1000G"
 129         depends on MACH_SUN4I
 130
 131 config TARGET_MELE_A1000
 132         bool "MELE_A1000"
 133         depends on MACH_SUN4I
 134
 135 config TARGET_MELE_M3
 136         bool "MELE_M3"
 137         depends on MACH_SUN7I
 138
 139 config TARGET_MELE_M9
 140         bool "MELE_M9"
 141         depends on MACH_SUN6I
 142
 143 config TARGET_MINI_X_1GB
 144         bool "MINI_X_1GB"
 145         depends on MACH_SUN4I
 146
 147 config TARGET_MINI_X
 148         bool "MINI_X"
 149         depends on MACH_SUN4I
 150
 151 config TARGET_MSI_PRIMO81
 152         bool "MSI Primo81 (7.85\" tablet)"
 153         depends on MACH_SUN6I
 154         ---help---
 155         The MSI Primo81 is an A31s based tablet, with 1G RAM, 16G NAND,
 156         1024x768 IPS LCD display, mono speaker, 0.3 MP front camera, 2.0 MP
 157         rear camera, 3500 mAh battery, gt911 touchscreen, mma8452 accelerometer
 158         and rtl8188etv usb wifi. Has "power", "volume+" and "volume-" buttons
 159         (both volume buttons are also connected to the UBOOT_SEL pin). The
 160         external connectors are represented by MicroSD slot, MiniHDMI, MicroUSB
 161         OTG and 3.5mm headphone jack. More details are available at
 162             http://linux-sunxi.org/MSI_Primo81
 163
 164 config TARGET_BA10_TV_BOX
 165         bool "BA10_TV_BOX"
 166         depends on MACH_SUN4I
 167
 168 config TARGET_I12_TVBOX
 169         bool "I12_TVBOX"
 170         depends on MACH_SUN7I
 171
 172 config TARGET_QT840A
 173         bool "QT840A"
 174         depends on MACH_SUN7I
 175
 176 config TARGET_R7DONGLE
 177         bool "R7DONGLE"
 178         depends on MACH_SUN5I
 179
 180 endchoice
 181
 182 config SYS_BOARD
 183         default "sunxi"
 184
 185 config SYS_SOC
 186         default "sunxi"
 187
 188 config SPL_FEL
 189         bool "SPL/FEL mode support"
 190         depends on SPL
 191         default n
 192
 193 config UART0_PORT_F
 194         bool "UART0 on MicroSD breakout board"
 195         depends on SPL_FEL
 196         default n
 197         ---help---
 198         Repurpose the SD card slot for getting access to the UART0 serial
 199         console. Primarily useful only for low level u-boot debugging on
 200         tablets, where normal UART0 is difficult to access and requires
 201         device disassembly and/or soldering. As the SD card can't be used
 202         at the same time, the system can be only booted in the FEL mode.
 203         Only enable this if you really know what you are doing.
 204
 205 config FDTFILE
 206         string "Default fdtfile env setting for this board"
 207
 208 config OLD_SUNXI_KERNEL_COMPAT
 209         boolean "Enable workarounds for booting old kernels"
 210         default n
 211         ---help---
 212         Set this to enable various workarounds for old kernels, this results in
 213         sub-optimal settings for newer kernels, only enable if needed.
 214
 215 config MMC0_CD_PIN
 216         string "Card detect pin for mmc0"
 217         default ""
 218         ---help---
 219         Set the card detect pin for mmc0, leave empty to not use cd. This
 220         takes a string in the format understood by sunxi_name_to_gpio, e.g.
 221         PH1 for pin 1 of port H.
 222
 223 config MMC1_CD_PIN
 224         string "Card detect pin for mmc1"
 225         default ""
 226         ---help---
 227         See MMC0_CD_PIN help text.
 228
 229 config MMC2_CD_PIN
 230         string "Card detect pin for mmc2"
 231         default ""
 232         ---help---
 233         See MMC0_CD_PIN help text.
 234
 235 config MMC3_CD_PIN
 236         string "Card detect pin for mmc3"
 237         default ""
 238         ---help---
 239         See MMC0_CD_PIN help text.
 240
 241 config MMC_SUNXI_SLOT_EXTRA
 242         int "mmc extra slot number"
 243         default -1
 244         ---help---
 245         sunxi builds always enable mmc0, some boards also have a second sdcard
 246         slot or emmc on mmc1 - mmc3. Setting this to 1, 2 or 3 will enable
 247         support for this.
 248
 249 config USB1_VBUS_PIN
 250         string "Vbus enable pin for usb1 (ehci0)"
 251         default "PH6" if MACH_SUN4I || MACH_SUN7I
 252         default "PH27" if MACH_SUN6I
 253         ---help---
 254         Set the Vbus enable pin for usb1 (ehci0, usb0 is the otg). This takes
 255         a string in the format understood by sunxi_name_to_gpio, e.g.
 256         PH1 for pin 1 of port H.
 257
 258 config USB2_VBUS_PIN
 259         string "Vbus enable pin for usb2 (ehci1)"
 260         default "PH3" if MACH_SUN4I || MACH_SUN7I
 261         default "PH24" if MACH_SUN6I
 262         ---help---
 263         See USB1_VBUS_PIN help text.
 264
 265 config VIDEO
 266         boolean "Enable graphical uboot console on HDMI"
 267         default y
 268         ---help---
 269         Say Y here to add support for using a cfb console on the HDMI output
 270         found on most sunxi devices.
 271
 272 config USB_KEYBOARD
 273         boolean "Enable USB keyboard support"
 274         default y
 275         ---help---
 276         Say Y here to add support for using a USB keyboard (typically used
 277         in combination with a graphical console on HDMI).
 278
 279 endif