doc/README.mpc8641hpcn

   1 Freescale MPC8641HPCN board
   2 ===========================
   3
   4 Created 05/24/2006 Haiying Wang
   5 -------------------------------
   6
   7 1. Building U-Boot
   8 ------------------
   9 The 86xx HPCN code base is known to compile using:
  10     Binutils 2.15, Gcc 3.4.3, Glibc 2.3.3
  11
  12     $ make MPC8641HPCN_config
  13     Configuring for MPC8641HPCN board...
  14
  15     $ make
  16
  17
  18 2. Switch and Jumper Setting
  19 ----------------------------
  20 Jumpers:
  21         J14 Pins 1-2 (near plcc32 socket)
  22
  23 Switches:
  24         SW1(1-5) = 01100        CFG_COREPLL     = 01000 :: CORE =   2:1
  25                                                   01100 :: CORE = 2.5:1
  26                                                   10000 :: CORE =   3:1
  27                                                   11100 :: CORE = 3.5:1
  28                                                   10100 :: CORE =   4:1
  29                                                   01110 :: CORE = 4.5:1
  30         SW1(6-8) = 001          CFG_SYSCLK      = 000   :: SYSCLK = 33MHz
  31                                                   001   :: SYSCLK = 40MHz
  32
  33         SW2(1-4) = 1100         CFG_CCBPLL      = 0010  :: 2X
  34                                                   0100  :: 4X
  35                                                   0110  :: 6X
  36                                                   1000  :: 8X
  37                                                   1010  :: 10X
  38                                                   1100  :: 12X
  39                                                   1110  :: 14X
  40                                                   0000  :: 16X
  41         SW2(5-8) = 1110         CFG_BOOTLOC     = 1110  :: boot 16-bit localbus
  42
  43         SW3(1-7) = 0011000      CFG_VID         = 0011000 :: VCORE = 1.2V
  44                                                   0100000 :: VCORE = 1.11V
  45         SW3(8)   = 0            VCC_PLAT        = 0     :: VCC_PLAT = 1.2V
  46                                                   1     :: VCC_PLAT = 1.0V
  47
  48         SW4(1-2) = 11           CFG_HOSTMODE    = 11    :: both prots host/root
  49         SW4(3-4) = 11           CFG_BOOTSEQ     = 11    :: no boot seq
  50         SW4(5-8) = 0011         CFG_IOPORT      = 0011  :: both PEX
  51
  52         SW5(1)   = 1            CFG_FLASHMAP    = 1     :: boot from flash
  53                                                   0     :: boot from PromJet
  54         SW5(2)   = 1            CFG_FLASHBANK   = 1     :: swap upper/lower
  55                                                          halves (virtual banks)
  56                                                   0     :: normal
  57         SW5(3)   = 0            CFG_FLASHWP     = 0     :: not protected
  58         SW5(4)   = 0            CFG_PORTDIV     = 1     :: 2:1 for PD4
  59                                                            1:1 for PD6
  60         SW5(5-6) = 11           CFG_PIXISOPT    = 11    :: s/w determined
  61         SW5(7-8) = 11           CFG_LADOPT      = 11    :: s/w determined
  62
  63         SW6(1)   = 1            CFG_CPUBOOT     = 1     :: no boot holdoff
  64         SW6(2)   = 1            CFG_BOOTADDR    = 1     :: no traslation
  65         SW6(3-5) = 000          CFG_REFCLKSEL   = 000   :: 100MHZ
  66         SW6(6)   = 1            CFG_SERROM_ADDR= 1      ::
  67         SW6(7)   = 1            CFG_MEMDEBUG    = 1     ::
  68         SW6(8)   = 1            CFG_DDRDEBUG    = 1     ::
  69
  70         SW8(1)   = 1            ACZ_SYNC        = 1     :: 48MHz on TP49
  71         SW8(2)   = 1            ACB_SYNC        = 1     :: THRMTRIP disabled
  72         SW8(3)   = 1            ACZ_SDOUT       = 1     :: p4 mode
  73         SW8(4)   = 1            ACB_SDOUT       = 1     :: PATA freq. = 133MHz
  74         SW8(5)   = 0            SUSLED          = 0     :: SouthBridge Mode
  75         SW8(6)   = 0            SPREAD          = 0     :: REFCLK SSCG Disabled
  76         SW8(7)   = 1            ACPWR           = 1     :: non-battery
  77         SW8(8)   = 0            CFG_IDWP        = 0     :: write enable
  78
  79
  80 3. Flash U-Boot
  81 ---------------
  82 The flash range 0xFF800000 to 0xFFFFFFFF can be divided into 2 halves.
  83 It is possible to use either half to boot using u-boot.  Switch 5 bit 2
  84 is used for this purpose.
  85
  86 0xFF800000 to 0xFFBFFFFF - 4MB
  87 0xFFC00000 to 0xFFFFFFFF - 4MB
  88 When this bit is 0, U-Boot is at 0xFFF00000.
  89 When this bit is 1, U-Boot is at 0xFFB00000.
  90
  91 Use the above mentioned flash commands to program the other half, and
  92 use switch 5, bit 2 to alternate between the halves.  Note: The booting
  93 version of U-Boot will always be at 0xFFF00000.
  94
  95 To Flash U-Boot into the booting bank (0xFFC00000 - 0xFFFFFFFF):
  96
  97         tftp 1000000 u-boot.bin
  98         protect off all
  99         erase fff00000 ffffffff
 100         cp.b 1000000 fff00100 80000
 101
 102 To Flash U-boot into the alternative bank (0xFF800000 - 0xFFBFFFFF):
 103
 104         tftp 1000000 u-boot.bin
 105         erase ffb00000 ffbfffff
 106         cp.b 1000000 ffb00100 80000
 107
 108
 109 4. Memory Map
 110 -------------
 111
 112         Memory Range                    Device          Size
 113         ------------                    ------          ----
 114         0x0000_0000     0x7fff_ffff     DDR             2G
 115         0x8000_0000     0x9fff_ffff     PCI1/PEX1 MEM   512M
 116         0xa000_0000     0xafff_ffff     PCI2/PEX2 MEM   512M
 117         0xf800_0000     0xf80f_ffff     CCSR            1M
 118         0xf810_0000     0xf81f_ffff     PIXIS           1M
 119         0xf840_0000     0xf840_3fff     Stack space     32K
 120         0xe200_0000     0xe2ff_ffff     PCI1/PEX1 IO    16M
 121         0xe300_0000     0xe3ff_ffff     PCI2/PEX2 IO    16M
 122         0xfe00_0000     0xfeff_ffff     Flash(alternate)16M
 123         0xff00_0000     0xffff_ffff     Flash(boot bank)16M
 124
 125 5. pixis_reset command
 126 --------------------
 127 A new command, "pixis_reset", is introduced to reset mpc8641hpcn board
 128 using the FPGA sequencer.  When the board restarts, it has the option
 129 of using either the current or alternate flash bank as the boot
 130 image, with or without the watchdog timer enabled, and finally with
 131 or without frequency changes.
 132
 133 Usage is;
 134
 135         pixis_reset
 136         pixis_reset altbank
 137         pixis_reset altbank wd
 138         pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
 139         pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
 140
 141 Examples;
 142
 143         /* reset to current bank, like "reset" command */
 144         pixis_reset
 145
 146         /* reset board but use the to alternate flash bank */
 147         pixis_reset altbank
 148
 149         /* reset board, use alternate flash bank with watchdog timer enabled*/
 150         pixis_reset altbank wd
 151
 152         /* reset board to alternate bank with frequency changed.
 153          * 40 is SYSCLK, 2.5 is COREPLL ratio, 10 is MPXPLL ratio
 154          */
 155         pixis-reset altbank cf 40 2.5 10
 156
 157 Valid clock choices are in the 8641 Reference Manuals.