drivers/gpu/drm/bridge/adv7511/adv7511_drv.c

   1 /*
   2  * Analog Devices ADV7511 HDMI transmitter driver
   3  *
   4  * Copyright 2012 Analog Devices Inc.
   5  *
   6  * Licensed under the GPL-2.
   7  */
   8
   9 #include <linux/device.h>
  10 #include <linux/gpio/consumer.h>
  11 #include <linux/module.h>
  12 #include <linux/of_device.h>
  13 #include <linux/slab.h>
  14 #include <linux/clk.h>
  15
  16 #include <drm/drmP.h>
  17 #include <drm/drm_atomic.h>
  18 #include <drm/drm_atomic_helper.h>
  19 #include <drm/drm_edid.h>
  20
  21 #include <media/cec.h>
  22
  23 #include "adv7511.h"
  24
  25 /* ADI recommended values for proper operation. */
  26 static const struct reg_sequence adv7511_fixed_registers[] = {
  27         { 0x98, 0x03 },
  28         { 0x9a, 0xe0 },
  29         { 0x9c, 0x30 },
  30         { 0x9d, 0x61 },
  31         { 0xa2, 0xa4 },
  32         { 0xa3, 0xa4 },
  33         { 0xe0, 0xd0 },
  34         { 0xf9, 0x00 },
  35         { 0x55, 0x02 },
  36 };
  37
  38 /* -----------------------------------------------------------------------------
  39  * Register access
  40  */
  41
  42 static const uint8_t adv7511_register_defaults[] = {
  43         0x12, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 00 */
  44         0x00, 0x00, 0x01, 0x0e, 0xbc, 0x18, 0x01, 0x13,
  45         0x25, 0x37, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 10 */
  46         0x46, 0x62, 0x04, 0xa8, 0x00, 0x00, 0x1c, 0x84,
  47         0x1c, 0xbf, 0x04, 0xa8, 0x1e, 0x70, 0x02, 0x1e, /* 20 */
  48         0x00, 0x00, 0x04, 0xa8, 0x08, 0x12, 0x1b, 0xac,
  49         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 30 */
  50         0x00, 0x00, 0x00, 0x80, 0x00, 0x00, 0x00, 0xb0,
  51         0x00, 0x50, 0x90, 0x7e, 0x79, 0x70, 0x00, 0x00, /* 40 */
  52         0x00, 0xa8, 0x80, 0x00, 0x00, 0x00, 0x00, 0x00,
  53         0x00, 0x00, 0x02, 0x0d, 0x00, 0x00, 0x00, 0x00, /* 50 */
  54         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
  55         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 60 */
  56         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
  57         0x01, 0x0a, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 70 */
  58         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
  59         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 80 */
  60         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
  61         0x00, 0x00, 0x00, 0x00, 0xc0, 0x00, 0x00, 0x00, /* 90 */
  62         0x0b, 0x02, 0x00, 0x18, 0x5a, 0x60, 0x00, 0x00,
  63         0x00, 0x00, 0x80, 0x80, 0x08, 0x04, 0x00, 0x00, /* a0 */
  64         0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x40, 0x14,
  65         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* b0 */
  66         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
  67         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* c0 */
  68         0x00, 0x03, 0x00, 0x00, 0x02, 0x00, 0x01, 0x04,
  69         0x30, 0xff, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, /* d0 */
  70         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x10, 0x01,
  71         0x80, 0x75, 0x00, 0x00, 0x60, 0x00, 0x00, 0x00, /* e0 */
  72         0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
  73         0x00, 0x00, 0x00, 0x00, 0x00, 0x75, 0x11, 0x00, /* f0 */
  74         0x00, 0x7c, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
  75 };
  76
  77 static bool adv7511_register_volatile(struct device *dev, unsigned int reg)
  78 {
  79         switch (reg) {
  80         case ADV7511_REG_CHIP_REVISION:
  81         case ADV7511_REG_SPDIF_FREQ:
  82         case ADV7511_REG_CTS_AUTOMATIC1:
  83         case ADV7511_REG_CTS_AUTOMATIC2:
  84         case ADV7511_REG_VIC_DETECTED:
  85         case ADV7511_REG_VIC_SEND:
  86         case ADV7511_REG_AUX_VIC_DETECTED:
  87         case ADV7511_REG_STATUS:
  88         case ADV7511_REG_GC(1):
  89         case ADV7511_REG_INT(0):
  90         case ADV7511_REG_INT(1):
  91         case ADV7511_REG_PLL_STATUS:
  92         case ADV7511_REG_AN(0):
  93         case ADV7511_REG_AN(1):
  94         case ADV7511_REG_AN(2):
  95         case ADV7511_REG_AN(3):
  96         case ADV7511_REG_AN(4):
  97         case ADV7511_REG_AN(5):
  98         case ADV7511_REG_AN(6):
  99         case ADV7511_REG_AN(7):
 100         case ADV7511_REG_HDCP_STATUS:
 101         case ADV7511_REG_BCAPS:
 102         case ADV7511_REG_BKSV(0):
 103         case ADV7511_REG_BKSV(1):
 104         case ADV7511_REG_BKSV(2):
 105         case ADV7511_REG_BKSV(3):
 106         case ADV7511_REG_BKSV(4):
 107         case ADV7511_REG_DDC_STATUS:
 108         case ADV7511_REG_EDID_READ_CTRL:
 109         case ADV7511_REG_BSTATUS(0):
 110         case ADV7511_REG_BSTATUS(1):
 111         case ADV7511_REG_CHIP_ID_HIGH:
 112         case ADV7511_REG_CHIP_ID_LOW:
 113                 return true;
 114         }
 115
 116         return false;
 117 }
 118
 119 static const struct regmap_config adv7511_regmap_config = {
 120         .reg_bits = 8,
 121         .val_bits = 8,
 122
 123         .max_register = 0xff,
 124         .cache_type = REGCACHE_RBTREE,
 125         .reg_defaults_raw = adv7511_register_defaults,
 126         .num_reg_defaults_raw = ARRAY_SIZE(adv7511_register_defaults),
 127
 128         .volatile_reg = adv7511_register_volatile,
 129 };
 130
 131 /* -----------------------------------------------------------------------------
 132  * Hardware configuration
 133  */
 134
 135 static void adv7511_set_colormap(struct adv7511 *adv7511, bool enable,
 136                                  const uint16_t *coeff,
 137                                  unsigned int scaling_factor)
 138 {
 139         unsigned int i;
 140
 141         regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(1),
 142                            ADV7511_CSC_UPDATE_MODE, ADV7511_CSC_UPDATE_MODE);
 143
 144         if (enable) {
 145                 for (i = 0; i < 12; ++i) {
 146                         regmap_update_bits(adv7511->regmap,
 147                                            ADV7511_REG_CSC_UPPER(i),
 148                                            0x1f, coeff[i] >> 8);
 149                         regmap_write(adv7511->regmap,
 150                                      ADV7511_REG_CSC_LOWER(i),
 151                                      coeff[i] & 0xff);
 152                 }
 153         }
 154
 155         if (enable)
 156                 regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(0),
 157                                    0xe0, 0x80 | (scaling_factor << 5));
 158         else
 159                 regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(0),
 160                                    0x80, 0x00);
 161
 162         regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(1),
 163                            ADV7511_CSC_UPDATE_MODE, 0);
 164 }
 165
 166 static int adv7511_packet_enable(struct adv7511 *adv7511, unsigned int packet)
 167 {
 168         if (packet & 0xff)
 169                 regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE0,
 170                                    packet, 0xff);
 171
 172         if (packet & 0xff00) {
 173                 packet >>= 8;
 174                 regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE1,
 175                                    packet, 0xff);
 176         }
 177
 178         return 0;
 179 }
 180
 181 static int adv7511_packet_disable(struct adv7511 *adv7511, unsigned int packet)
 182 {
 183         if (packet & 0xff)
 184                 regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE0,
 185                                    packet, 0x00);
 186
 187         if (packet & 0xff00) {
 188                 packet >>= 8;
 189                 regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE1,
 190                                    packet, 0x00);
 191         }
 192
 193         return 0;
 194 }
 195
 196 /* Coefficients for adv7511 color space conversion */
 197 static const uint16_t adv7511_csc_ycbcr_to_rgb[] = {
 198         0x0734, 0x04ad, 0x0000, 0x1c1b,
 199         0x1ddc, 0x04ad, 0x1f24, 0x0135,
 200         0x0000, 0x04ad, 0x087c, 0x1b77,
 201 };
 202
 203 static void adv7511_set_config_csc(struct adv7511 *adv7511,
 204                                    struct drm_connector *connector,
 205                                    bool rgb, bool hdmi_mode)
 206 {
 207         struct adv7511_video_config config;
 208         bool output_format_422, output_format_ycbcr;
 209         unsigned int mode;
 210         uint8_t infoframe[17];
 211
 212         config.hdmi_mode = hdmi_mode;
 213
 214         hdmi_avi_infoframe_init(&config.avi_infoframe);
 215
 216         config.avi_infoframe.scan_mode = HDMI_SCAN_MODE_UNDERSCAN;
 217
 218         if (rgb) {
 219                 config.csc_enable = false;
 220                 config.avi_infoframe.colorspace = HDMI_COLORSPACE_RGB;
 221         } else {
 222                 config.csc_scaling_factor = ADV7511_CSC_SCALING_4;
 223                 config.csc_coefficents = adv7511_csc_ycbcr_to_rgb;
 224
 225                 if ((connector->display_info.color_formats &
 226                      DRM_COLOR_FORMAT_YCRCB422) &&
 227                     config.hdmi_mode) {
 228                         config.csc_enable = false;
 229                         config.avi_infoframe.colorspace =
 230                                 HDMI_COLORSPACE_YUV422;
 231                 } else {
 232                         config.csc_enable = true;
 233                         config.avi_infoframe.colorspace = HDMI_COLORSPACE_RGB;
 234                 }
 235         }
 236
 237         if (config.hdmi_mode) {
 238                 mode = ADV7511_HDMI_CFG_MODE_HDMI;
 239
 240                 switch (config.avi_infoframe.colorspace) {
 241                 case HDMI_COLORSPACE_YUV444:
 242                         output_format_422 = false;
 243                         output_format_ycbcr = true;
 244                         break;
 245                 case HDMI_COLORSPACE_YUV422:
 246                         output_format_422 = true;
 247                         output_format_ycbcr = true;
 248                         break;
 249                 default:
 250                         output_format_422 = false;
 251                         output_format_ycbcr = false;
 252                         break;
 253                 }
 254         } else {
 255                 mode = ADV7511_HDMI_CFG_MODE_DVI;
 256                 output_format_422 = false;
 257                 output_format_ycbcr = false;
 258         }
 259
 260         adv7511_packet_disable(adv7511, ADV7511_PACKET_ENABLE_AVI_INFOFRAME);
 261
 262         adv7511_set_colormap(adv7511, config.csc_enable,
 263                              config.csc_coefficents,
 264                              config.csc_scaling_factor);
 265
 266         regmap_update_bits(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG1, 0x81,
 267                            (output_format_422 << 7) | output_format_ycbcr);
 268
 269         regmap_update_bits(adv7511->regmap, ADV7511_REG_HDCP_HDMI_CFG,
 270                            ADV7511_HDMI_CFG_MODE_MASK, mode);
 271
 272         hdmi_avi_infoframe_pack(&config.avi_infoframe, infoframe,
 273                                 sizeof(infoframe));
 274
 275         /* The AVI infoframe id is not configurable */
 276         regmap_bulk_write(adv7511->regmap, ADV7511_REG_AVI_INFOFRAME_VERSION,
 277                           infoframe + 1, sizeof(infoframe) - 1);
 278
 279         adv7511_packet_enable(adv7511, ADV7511_PACKET_ENABLE_AVI_INFOFRAME);
 280 }
 281
 282 static void adv7511_set_link_config(struct adv7511 *adv7511,
 283                                     const struct adv7511_link_config *config)
 284 {
 285         /*
 286          * The input style values documented in the datasheet don't match the
 287          * hardware register field values :-(
 288          */
 289         static const unsigned int input_styles[4] = { 0, 2, 1, 3 };
 290
 291         unsigned int clock_delay;
 292         unsigned int color_depth;
 293         unsigned int input_id;
 294
 295         clock_delay = (config->clock_delay + 1200) / 400;
 296         color_depth = config->input_color_depth == 8 ? 3
 297                     : (config->input_color_depth == 10 ? 1 : 2);
 298
 299         /* TODO Support input ID 6 */
 300         if (config->input_colorspace != HDMI_COLORSPACE_YUV422)
 301                 input_id = config->input_clock == ADV7511_INPUT_CLOCK_DDR
 302                          ? 5 : 0;
 303         else if (config->input_clock == ADV7511_INPUT_CLOCK_DDR)
 304                 input_id = config->embedded_sync ? 8 : 7;
 305         else if (config->input_clock == ADV7511_INPUT_CLOCK_2X)
 306                 input_id = config->embedded_sync ? 4 : 3;
 307         else
 308                 input_id = config->embedded_sync ? 2 : 1;
 309
 310         regmap_update_bits(adv7511->regmap, ADV7511_REG_I2C_FREQ_ID_CFG, 0xf,
 311                            input_id);
 312         regmap_update_bits(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG1, 0x7e,
 313                            (color_depth << 4) |
 314                            (input_styles[config->input_style] << 2));
 315         regmap_write(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG2,
 316                      config->input_justification << 3);
 317         regmap_write(adv7511->regmap, ADV7511_REG_TIMING_GEN_SEQ,
 318                      config->sync_pulse << 2);
 319
 320         regmap_write(adv7511->regmap, 0xba, clock_delay << 5);
 321
 322         adv7511->embedded_sync = config->embedded_sync;
 323         adv7511->hsync_polarity = config->hsync_polarity;
 324         adv7511->vsync_polarity = config->vsync_polarity;
 325         adv7511->rgb = config->input_colorspace == HDMI_COLORSPACE_RGB;
 326 }
 327
 328 static void __adv7511_power_on(struct adv7511 *adv7511)
 329 {
 330         adv7511->current_edid_segment = -1;
 331
 332         regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
 333                            ADV7511_POWER_POWER_DOWN, 0);
 334         if (adv7511->i2c_main->irq) {
 335                 /*
 336                  * Documentation says the INT_ENABLE registers are reset in
 337                  * POWER_DOWN mode. My 7511w preserved the bits, however.
 338                  * Still, let's be safe and stick to the documentation.
 339                  */
 340                 regmap_write(adv7511->regmap, ADV7511_REG_INT_ENABLE(0),
 341                              ADV7511_INT0_EDID_READY | ADV7511_INT0_HPD);
 342                 regmap_update_bits(adv7511->regmap,
 343                                    ADV7511_REG_INT_ENABLE(1),
 344                                    ADV7511_INT1_DDC_ERROR,
 345                                    ADV7511_INT1_DDC_ERROR);
 346         }
 347
 348         /*
 349          * Per spec it is allowed to pulse the HPD signal to indicate that the
 350          * EDID information has changed. Some monitors do this when they wakeup
 351          * from standby or are enabled. When the HPD goes low the adv7511 is
 352          * reset and the outputs are disabled which might cause the monitor to
 353          * go to standby again. To avoid this we ignore the HPD pin for the
 354          * first few seconds after enabling the output.
 355          */
 356         regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
 357                            ADV7511_REG_POWER2_HPD_SRC_MASK,
 358                            ADV7511_REG_POWER2_HPD_SRC_NONE);
 359 }
 360
 361 static void adv7511_power_on(struct adv7511 *adv7511)
 362 {
 363         __adv7511_power_on(adv7511);
 364
 365         /*
 366          * Most of the registers are reset during power down or when HPD is low.
 367          */
 368         regcache_sync(adv7511->regmap);
 369
 370         if (adv7511->type == ADV7533)
 371                 adv7533_dsi_power_on(adv7511);
 372         adv7511->powered = true;
 373 }
 374
 375 static void __adv7511_power_off(struct adv7511 *adv7511)
 376 {
 377         /* TODO: setup additional power down modes */
 378         regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
 379                            ADV7511_POWER_POWER_DOWN,
 380                            ADV7511_POWER_POWER_DOWN);
 381         regmap_update_bits(adv7511->regmap,
 382                            ADV7511_REG_INT_ENABLE(1),
 383                            ADV7511_INT1_DDC_ERROR, 0);
 384         regcache_mark_dirty(adv7511->regmap);
 385 }
 386
 387 static void adv7511_power_off(struct adv7511 *adv7511)
 388 {
 389         __adv7511_power_off(adv7511);
 390         if (adv7511->type == ADV7533)
 391                 adv7533_dsi_power_off(adv7511);
 392         adv7511->powered = false;
 393 }
 394
 395 /* -----------------------------------------------------------------------------
 396  * Interrupt and hotplug detection
 397  */
 398
 399 static bool adv7511_hpd(struct adv7511 *adv7511)
 400 {
 401         unsigned int irq0;
 402         int ret;
 403
 404         ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0);
 405         if (ret < 0)
 406                 return false;
 407
 408         if (irq0 & ADV7511_INT0_HPD) {
 409                 regmap_write(adv7511->regmap, ADV7511_REG_INT(0),
 410                              ADV7511_INT0_HPD);
 411                 return true;
 412         }
 413
 414         return false;
 415 }
 416
 417 static void adv7511_hpd_work(struct work_struct *work)
 418 {
 419         struct adv7511 *adv7511 = container_of(work, struct adv7511, hpd_work);
 420         enum drm_connector_status status;
 421         unsigned int val;
 422         int ret;
 423
 424         ret = regmap_read(adv7511->regmap, ADV7511_REG_STATUS, &val);
 425         if (ret < 0)
 426                 status = connector_status_disconnected;
 427         else if (val & ADV7511_STATUS_HPD)
 428                 status = connector_status_connected;
 429         else
 430                 status = connector_status_disconnected;
 431
 432         /*
 433          * The bridge resets its registers on unplug. So when we get a plug
 434          * event and we're already supposed to be powered, cycle the bridge to
 435          * restore its state.
 436          */
 437         if (status == connector_status_connected &&
 438             adv7511->connector.status == connector_status_disconnected &&
 439             adv7511->powered) {
 440                 regcache_mark_dirty(adv7511->regmap);
 441                 adv7511_power_on(adv7511);
 442         }
 443
 444         if (adv7511->connector.status != status) {
 445                 adv7511->connector.status = status;
 446                 if (status == connector_status_disconnected)
 447                         cec_phys_addr_invalidate(adv7511->cec_adap);
 448                 drm_kms_helper_hotplug_event(adv7511->connector.dev);
 449         }
 450 }
 451
 452 static int adv7511_irq_process(struct adv7511 *adv7511, bool process_hpd)
 453 {
 454         unsigned int irq0, irq1;
 455         int ret;
 456
 457         ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0);
 458         if (ret < 0)
 459                 return ret;
 460
 461         ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(1), &irq1);
 462         if (ret < 0)
 463                 return ret;
 464
 465         regmap_write(adv7511->regmap, ADV7511_REG_INT(0), irq0);
 466         regmap_write(adv7511->regmap, ADV7511_REG_INT(1), irq1);
 467
 468         if (process_hpd && irq0 & ADV7511_INT0_HPD && adv7511->bridge.encoder)
 469                 schedule_work(&adv7511->hpd_work);
 470
 471         if (irq0 & ADV7511_INT0_EDID_READY || irq1 & ADV7511_INT1_DDC_ERROR) {
 472                 adv7511->edid_read = true;
 473
 474                 if (adv7511->i2c_main->irq)
 475                         wake_up_all(&adv7511->wq);
 476         }
 477
 478 #ifdef CONFIG_DRM_I2C_ADV7511_CEC
 479         adv7511_cec_irq_process(adv7511, irq1);
 480 #endif
 481
 482         return 0;
 483 }
 484
 485 static irqreturn_t adv7511_irq_handler(int irq, void *devid)
 486 {
 487         struct adv7511 *adv7511 = devid;
 488         int ret;
 489
 490         ret = adv7511_irq_process(adv7511, true);
 491         return ret < 0 ? IRQ_NONE : IRQ_HANDLED;
 492 }
 493
 494 /* -----------------------------------------------------------------------------
 495  * EDID retrieval
 496  */
 497
 498 static int adv7511_wait_for_edid(struct adv7511 *adv7511, int timeout)
 499 {
 500         int ret;
 501
 502         if (adv7511->i2c_main->irq) {
 503                 ret = wait_event_interruptible_timeout(adv7511->wq,
 504                                 adv7511->edid_read, msecs_to_jiffies(timeout));
 505         } else {
 506                 for (; timeout > 0; timeout -= 25) {
 507                         ret = adv7511_irq_process(adv7511, false);
 508                         if (ret < 0)
 509                                 break;
 510
 511                         if (adv7511->edid_read)
 512                                 break;
 513
 514                         msleep(25);
 515                 }
 516         }
 517
 518         return adv7511->edid_read ? 0 : -EIO;
 519 }
 520
 521 static int adv7511_get_edid_block(void *data, u8 *buf, unsigned int block,
 522                                   size_t len)
 523 {
 524         struct adv7511 *adv7511 = data;
 525         struct i2c_msg xfer[2];
 526         uint8_t offset;
 527         unsigned int i;
 528         int ret;
 529
 530         if (len > 128)
 531                 return -EINVAL;
 532
 533         if (adv7511->current_edid_segment != block / 2) {
 534                 unsigned int status;
 535
 536                 ret = regmap_read(adv7511->regmap, ADV7511_REG_DDC_STATUS,
 537                                   &status);
 538                 if (ret < 0)
 539                         return ret;
 540
 541                 if (status != 2) {
 542                         adv7511->edid_read = false;
 543                         regmap_write(adv7511->regmap, ADV7511_REG_EDID_SEGMENT,
 544                                      block);
 545                         ret = adv7511_wait_for_edid(adv7511, 200);
 546                         if (ret < 0)
 547                                 return ret;
 548                 }
 549
 550                 /* Break this apart, hopefully more I2C controllers will
 551                  * support 64 byte transfers than 256 byte transfers
 552                  */
 553
 554                 xfer[0].addr = adv7511->i2c_edid->addr;
 555                 xfer[0].flags = 0;
 556                 xfer[0].len = 1;
 557                 xfer[0].buf = &offset;
 558                 xfer[1].addr = adv7511->i2c_edid->addr;
 559                 xfer[1].flags = I2C_M_RD;
 560                 xfer[1].len = 64;
 561                 xfer[1].buf = adv7511->edid_buf;
 562
 563                 offset = 0;
 564
 565                 for (i = 0; i < 4; ++i) {
 566                         ret = i2c_transfer(adv7511->i2c_edid->adapter, xfer,
 567                                            ARRAY_SIZE(xfer));
 568                         if (ret < 0)
 569                                 return ret;
 570                         else if (ret != 2)
 571                                 return -EIO;
 572
 573                         xfer[1].buf += 64;
 574                         offset += 64;
 575                 }
 576
 577                 adv7511->current_edid_segment = block / 2;
 578         }
 579
 580         if (block % 2 == 0)
 581                 memcpy(buf, adv7511->edid_buf, len);
 582         else
 583                 memcpy(buf, adv7511->edid_buf + 128, len);
 584
 585         return 0;
 586 }
 587
 588 /* -----------------------------------------------------------------------------
 589  * ADV75xx helpers
 590  */
 591
 592 static int adv7511_get_modes(struct adv7511 *adv7511,
 593                              struct drm_connector *connector)
 594 {
 595         struct edid *edid;
 596         unsigned int count;
 597
 598         /* Reading the EDID only works if the device is powered */
 599         if (!adv7511->powered) {
 600                 unsigned int edid_i2c_addr =
 601                                         (adv7511->i2c_edid->addr << 1);
 602
 603                 __adv7511_power_on(adv7511);
 604
 605                 /* Reset the EDID_I2C_ADDR register as it might be cleared */
 606                 regmap_write(adv7511->regmap, ADV7511_REG_EDID_I2C_ADDR,
 607                              edid_i2c_addr);
 608         }
 609
 610         edid = drm_do_get_edid(connector, adv7511_get_edid_block, adv7511);
 611
 612         if (!adv7511->powered)
 613                 __adv7511_power_off(adv7511);
 614
 615
 616         drm_connector_update_edid_property(connector, edid);
 617         count = drm_add_edid_modes(connector, edid);
 618
 619         adv7511_set_config_csc(adv7511, connector, adv7511->rgb,
 620                                drm_detect_hdmi_monitor(edid));
 621
 622         cec_s_phys_addr_from_edid(adv7511->cec_adap, edid);
 623
 624         kfree(edid);
 625
 626         return count;
 627 }
 628
 629 static enum drm_connector_status
 630 adv7511_detect(struct adv7511 *adv7511, struct drm_connector *connector)
 631 {
 632         enum drm_connector_status status;
 633         unsigned int val;
 634         bool hpd;
 635         int ret;
 636
 637         ret = regmap_read(adv7511->regmap, ADV7511_REG_STATUS, &val);
 638         if (ret < 0)
 639                 return connector_status_disconnected;
 640
 641         if (val & ADV7511_STATUS_HPD)
 642                 status = connector_status_connected;
 643         else
 644                 status = connector_status_disconnected;
 645
 646         hpd = adv7511_hpd(adv7511);
 647
 648         /* The chip resets itself when the cable is disconnected, so in case
 649          * there is a pending HPD interrupt and the cable is connected there was
 650          * at least one transition from disconnected to connected and the chip
 651          * has to be reinitialized. */
 652         if (status == connector_status_connected && hpd && adv7511->powered) {
 653                 regcache_mark_dirty(adv7511->regmap);
 654                 adv7511_power_on(adv7511);
 655                 adv7511_get_modes(adv7511, connector);
 656                 if (adv7511->status == connector_status_connected)
 657                         status = connector_status_disconnected;
 658         } else {
 659                 /* Renable HPD sensing */
 660                 regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
 661                                    ADV7511_REG_POWER2_HPD_SRC_MASK,
 662                                    ADV7511_REG_POWER2_HPD_SRC_BOTH);
 663         }
 664
 665         adv7511->status = status;
 666         return status;
 667 }
 668
 669 static enum drm_mode_status adv7511_mode_valid(struct adv7511 *adv7511,
 670                               struct drm_display_mode *mode)
 671 {
 672         if (mode->clock > 165000)
 673                 return MODE_CLOCK_HIGH;
 674
 675         return MODE_OK;
 676 }
 677
 678 static void adv7511_mode_set(struct adv7511 *adv7511,
 679                              struct drm_display_mode *mode,
 680                              struct drm_display_mode *adj_mode)
 681 {
 682         unsigned int low_refresh_rate;
 683         unsigned int hsync_polarity = 0;
 684         unsigned int vsync_polarity = 0;
 685
 686         if (adv7511->embedded_sync) {
 687                 unsigned int hsync_offset, hsync_len;
 688                 unsigned int vsync_offset, vsync_len;
 689
 690                 hsync_offset = adj_mode->crtc_hsync_start -
 691                                adj_mode->crtc_hdisplay;
 692                 vsync_offset = adj_mode->crtc_vsync_start -
 693                                adj_mode->crtc_vdisplay;
 694                 hsync_len = adj_mode->crtc_hsync_end -
 695                             adj_mode->crtc_hsync_start;
 696                 vsync_len = adj_mode->crtc_vsync_end -
 697                             adj_mode->crtc_vsync_start;
 698
 699                 /* The hardware vsync generator has a off-by-one bug */
 700                 vsync_offset += 1;
 701
 702                 regmap_write(adv7511->regmap, ADV7511_REG_HSYNC_PLACEMENT_MSB,
 703                              ((hsync_offset >> 10) & 0x7) << 5);
 704                 regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(0),
 705                              (hsync_offset >> 2) & 0xff);
 706                 regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(1),
 707                              ((hsync_offset & 0x3) << 6) |
 708                              ((hsync_len >> 4) & 0x3f));
 709                 regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(2),
 710                              ((hsync_len & 0xf) << 4) |
 711                              ((vsync_offset >> 6) & 0xf));
 712                 regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(3),
 713                              ((vsync_offset & 0x3f) << 2) |
 714                              ((vsync_len >> 8) & 0x3));
 715                 regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(4),
 716                              vsync_len & 0xff);
 717
 718                 hsync_polarity = !(adj_mode->flags & DRM_MODE_FLAG_PHSYNC);
 719                 vsync_polarity = !(adj_mode->flags & DRM_MODE_FLAG_PVSYNC);
 720         } else {
 721                 enum adv7511_sync_polarity mode_hsync_polarity;
 722                 enum adv7511_sync_polarity mode_vsync_polarity;
 723
 724                 /**
 725                  * If the input signal is always low or always high we want to
 726                  * invert or let it passthrough depending on the polarity of the
 727                  * current mode.
 728                  **/
 729                 if (adj_mode->flags & DRM_MODE_FLAG_NHSYNC)
 730                         mode_hsync_polarity = ADV7511_SYNC_POLARITY_LOW;
 731                 else
 732                         mode_hsync_polarity = ADV7511_SYNC_POLARITY_HIGH;
 733
 734                 if (adj_mode->flags & DRM_MODE_FLAG_NVSYNC)
 735                         mode_vsync_polarity = ADV7511_SYNC_POLARITY_LOW;
 736                 else
 737                         mode_vsync_polarity = ADV7511_SYNC_POLARITY_HIGH;
 738
 739                 if (adv7511->hsync_polarity != mode_hsync_polarity &&
 740                     adv7511->hsync_polarity !=
 741                     ADV7511_SYNC_POLARITY_PASSTHROUGH)
 742                         hsync_polarity = 1;
 743
 744                 if (adv7511->vsync_polarity != mode_vsync_polarity &&
 745                     adv7511->vsync_polarity !=
 746                     ADV7511_SYNC_POLARITY_PASSTHROUGH)
 747                         vsync_polarity = 1;
 748         }
 749
 750         if (drm_mode_vrefresh(mode) <= 24)
 751                 low_refresh_rate = ADV7511_LOW_REFRESH_RATE_24HZ;
 752         else if (drm_mode_vrefresh(mode) <= 25)
 753                 low_refresh_rate = ADV7511_LOW_REFRESH_RATE_25HZ;
 754         else if (drm_mode_vrefresh(mode) <= 30)
 755                 low_refresh_rate = ADV7511_LOW_REFRESH_RATE_30HZ;
 756         else
 757                 low_refresh_rate = ADV7511_LOW_REFRESH_RATE_NONE;
 758
 759         regmap_update_bits(adv7511->regmap, 0xfb,
 760                 0x6, low_refresh_rate << 1);
 761         regmap_update_bits(adv7511->regmap, 0x17,
 762                 0x60, (vsync_polarity << 6) | (hsync_polarity << 5));
 763
 764         if (adv7511->type == ADV7533)
 765                 adv7533_mode_set(adv7511, adj_mode);
 766
 767         drm_mode_copy(&adv7511->curr_mode, adj_mode);
 768
 769         /*
 770          * TODO Test first order 4:2:2 to 4:4:4 up conversion method, which is
 771          * supposed to give better results.
 772          */
 773
 774         adv7511->f_tmds = mode->clock;
 775 }
 776
 777 /* Connector funcs */
 778 static struct adv7511 *connector_to_adv7511(struct drm_connector *connector)
 779 {
 780         return container_of(connector, struct adv7511, connector);
 781 }
 782
 783 static int adv7511_connector_get_modes(struct drm_connector *connector)
 784 {
 785         struct adv7511 *adv = connector_to_adv7511(connector);
 786
 787         return adv7511_get_modes(adv, connector);
 788 }
 789
 790 static enum drm_mode_status
 791 adv7511_connector_mode_valid(struct drm_connector *connector,
 792                              struct drm_display_mode *mode)
 793 {
 794         struct adv7511 *adv = connector_to_adv7511(connector);
 795
 796         return adv7511_mode_valid(adv, mode);
 797 }
 798
 799 static struct drm_connector_helper_funcs adv7511_connector_helper_funcs = {
 800         .get_modes = adv7511_connector_get_modes,
 801         .mode_valid = adv7511_connector_mode_valid,
 802 };
 803
 804 static enum drm_connector_status
 805 adv7511_connector_detect(struct drm_connector *connector, bool force)
 806 {
 807         struct adv7511 *adv = connector_to_adv7511(connector);
 808
 809         return adv7511_detect(adv, connector);
 810 }
 811
 812 static const struct drm_connector_funcs adv7511_connector_funcs = {
 813         .fill_modes = drm_helper_probe_single_connector_modes,
 814         .detect = adv7511_connector_detect,
 815         .destroy = drm_connector_cleanup,
 816         .reset = drm_atomic_helper_connector_reset,
 817         .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
 818         .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
 819 };
 820
 821 /* Bridge funcs */
 822 static struct adv7511 *bridge_to_adv7511(struct drm_bridge *bridge)
 823 {
 824         return container_of(bridge, struct adv7511, bridge);
 825 }
 826
 827 static void adv7511_bridge_enable(struct drm_bridge *bridge)
 828 {
 829         struct adv7511 *adv = bridge_to_adv7511(bridge);
 830
 831         adv7511_power_on(adv);
 832 }
 833
 834 static void adv7511_bridge_disable(struct drm_bridge *bridge)
 835 {
 836         struct adv7511 *adv = bridge_to_adv7511(bridge);
 837
 838         adv7511_power_off(adv);
 839 }
 840
 841 static void adv7511_bridge_mode_set(struct drm_bridge *bridge,
 842                                     struct drm_display_mode *mode,
 843                                     struct drm_display_mode *adj_mode)
 844 {
 845         struct adv7511 *adv = bridge_to_adv7511(bridge);
 846
 847         adv7511_mode_set(adv, mode, adj_mode);
 848 }
 849
 850 static int adv7511_bridge_attach(struct drm_bridge *bridge)
 851 {
 852         struct adv7511 *adv = bridge_to_adv7511(bridge);
 853         int ret;
 854
 855         if (!bridge->encoder) {
 856                 DRM_ERROR("Parent encoder object not found");
 857                 return -ENODEV;
 858         }
 859
 860         if (adv->i2c_main->irq)
 861                 adv->connector.polled = DRM_CONNECTOR_POLL_HPD;
 862         else
 863                 adv->connector.polled = DRM_CONNECTOR_POLL_CONNECT |
 864                                 DRM_CONNECTOR_POLL_DISCONNECT;
 865
 866         ret = drm_connector_init(bridge->dev, &adv->connector,
 867                                  &adv7511_connector_funcs,
 868                                  DRM_MODE_CONNECTOR_HDMIA);
 869         if (ret) {
 870                 DRM_ERROR("Failed to initialize connector with drm\n");
 871                 return ret;
 872         }
 873         drm_connector_helper_add(&adv->connector,
 874                                  &adv7511_connector_helper_funcs);
 875         drm_connector_attach_encoder(&adv->connector, bridge->encoder);
 876
 877         if (adv->type == ADV7533)
 878                 ret = adv7533_attach_dsi(adv);
 879
 880         if (adv->i2c_main->irq)
 881                 regmap_write(adv->regmap, ADV7511_REG_INT_ENABLE(0),
 882                              ADV7511_INT0_HPD);
 883
 884         return ret;
 885 }
 886
 887 static const struct drm_bridge_funcs adv7511_bridge_funcs = {
 888         .enable = adv7511_bridge_enable,
 889         .disable = adv7511_bridge_disable,
 890         .mode_set = adv7511_bridge_mode_set,
 891         .attach = adv7511_bridge_attach,
 892 };
 893
 894 /* -----------------------------------------------------------------------------
 895  * Probe & remove
 896  */
 897
 898 static const char * const adv7511_supply_names[] = {
 899         "avdd",
 900         "dvdd",
 901         "pvdd",
 902         "bgvdd",
 903         "dvdd-3v",
 904 };
 905
 906 static const char * const adv7533_supply_names[] = {
 907         "avdd",
 908         "dvdd",
 909         "pvdd",
 910         "a2vdd",
 911         "v3p3",
 912         "v1p2",
 913 };
 914
 915 static int adv7511_init_regulators(struct adv7511 *adv)
 916 {
 917         struct device *dev = &adv->i2c_main->dev;
 918         const char * const *supply_names;
 919         unsigned int i;
 920         int ret;
 921
 922         if (adv->type == ADV7511) {
 923                 supply_names = adv7511_supply_names;
 924                 adv->num_supplies = ARRAY_SIZE(adv7511_supply_names);
 925         } else {
 926                 supply_names = adv7533_supply_names;
 927                 adv->num_supplies = ARRAY_SIZE(adv7533_supply_names);
 928         }
 929
 930         adv->supplies = devm_kcalloc(dev, adv->num_supplies,
 931                                      sizeof(*adv->supplies), GFP_KERNEL);
 932         if (!adv->supplies)
 933                 return -ENOMEM;
 934
 935         for (i = 0; i < adv->num_supplies; i++)
 936                 adv->supplies[i].supply = supply_names[i];
 937
 938         ret = devm_regulator_bulk_get(dev, adv->num_supplies, adv->supplies);
 939         if (ret)
 940                 return ret;
 941
 942         return regulator_bulk_enable(adv->num_supplies, adv->supplies);
 943 }
 944
 945 static void adv7511_uninit_regulators(struct adv7511 *adv)
 946 {
 947         regulator_bulk_disable(adv->num_supplies, adv->supplies);
 948 }
 949
 950 static bool adv7511_cec_register_volatile(struct device *dev, unsigned int reg)
 951 {
 952         struct i2c_client *i2c = to_i2c_client(dev);
 953         struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
 954
 955         if (adv7511->type == ADV7533)
 956                 reg -= ADV7533_REG_CEC_OFFSET;
 957
 958         switch (reg) {
 959         case ADV7511_REG_CEC_RX_FRAME_HDR:
 960         case ADV7511_REG_CEC_RX_FRAME_DATA0...
 961                 ADV7511_REG_CEC_RX_FRAME_DATA0 + 14:
 962         case ADV7511_REG_CEC_RX_FRAME_LEN:
 963         case ADV7511_REG_CEC_RX_BUFFERS:
 964         case ADV7511_REG_CEC_TX_LOW_DRV_CNT:
 965                 return true;
 966         }
 967
 968         return false;
 969 }
 970
 971 static const struct regmap_config adv7511_cec_regmap_config = {
 972         .reg_bits = 8,
 973         .val_bits = 8,
 974
 975         .max_register = 0xff,
 976         .cache_type = REGCACHE_RBTREE,
 977         .volatile_reg = adv7511_cec_register_volatile,
 978 };
 979
 980 static int adv7511_init_cec_regmap(struct adv7511 *adv)
 981 {
 982         int ret;
 983
 984         adv->i2c_cec = i2c_new_secondary_device(adv->i2c_main, "cec",
 985                                                 ADV7511_CEC_I2C_ADDR_DEFAULT);
 986         if (!adv->i2c_cec)
 987                 return -EINVAL;
 988         i2c_set_clientdata(adv->i2c_cec, adv);
 989
 990         adv->regmap_cec = devm_regmap_init_i2c(adv->i2c_cec,
 991                                         &adv7511_cec_regmap_config);
 992         if (IS_ERR(adv->regmap_cec)) {
 993                 ret = PTR_ERR(adv->regmap_cec);
 994                 goto err;
 995         }
 996
 997         if (adv->type == ADV7533) {
 998                 ret = adv7533_patch_cec_registers(adv);
 999                 if (ret)
1000                         goto err;
1001         }
1002
1003         return 0;
1004 err:
1005         i2c_unregister_device(adv->i2c_cec);
1006         return ret;
1007 }
1008
1009 static int adv7511_parse_dt(struct device_node *np,
1010                             struct adv7511_link_config *config)
1011 {
1012         const char *str;
1013         int ret;
1014
1015         of_property_read_u32(np, "adi,input-depth", &config->input_color_depth);
1016         if (config->input_color_depth != 8 && config->input_color_depth != 10 &&
1017             config->input_color_depth != 12)
1018                 return -EINVAL;
1019
1020         ret = of_property_read_string(np, "adi,input-colorspace", &str);
1021         if (ret < 0)
1022                 return ret;
1023
1024         if (!strcmp(str, "rgb"))
1025                 config->input_colorspace = HDMI_COLORSPACE_RGB;
1026         else if (!strcmp(str, "yuv422"))
1027                 config->input_colorspace = HDMI_COLORSPACE_YUV422;
1028         else if (!strcmp(str, "yuv444"))
1029                 config->input_colorspace = HDMI_COLORSPACE_YUV444;
1030         else
1031                 return -EINVAL;
1032
1033         ret = of_property_read_string(np, "adi,input-clock", &str);
1034         if (ret < 0)
1035                 return ret;
1036
1037         if (!strcmp(str, "1x"))
1038                 config->input_clock = ADV7511_INPUT_CLOCK_1X;
1039         else if (!strcmp(str, "2x"))
1040                 config->input_clock = ADV7511_INPUT_CLOCK_2X;
1041         else if (!strcmp(str, "ddr"))
1042                 config->input_clock = ADV7511_INPUT_CLOCK_DDR;
1043         else
1044                 return -EINVAL;
1045
1046         if (config->input_colorspace == HDMI_COLORSPACE_YUV422 ||
1047             config->input_clock != ADV7511_INPUT_CLOCK_1X) {
1048                 ret = of_property_read_u32(np, "adi,input-style",
1049                                            &config->input_style);
1050                 if (ret)
1051                         return ret;
1052
1053                 if (config->input_style < 1 || config->input_style > 3)
1054                         return -EINVAL;
1055
1056                 ret = of_property_read_string(np, "adi,input-justification",
1057                                               &str);
1058                 if (ret < 0)
1059                         return ret;
1060
1061                 if (!strcmp(str, "left"))
1062                         config->input_justification =
1063                                 ADV7511_INPUT_JUSTIFICATION_LEFT;
1064                 else if (!strcmp(str, "evenly"))
1065                         config->input_justification =
1066                                 ADV7511_INPUT_JUSTIFICATION_EVENLY;
1067                 else if (!strcmp(str, "right"))
1068                         config->input_justification =
1069                                 ADV7511_INPUT_JUSTIFICATION_RIGHT;
1070                 else
1071                         return -EINVAL;
1072
1073         } else {
1074                 config->input_style = 1;
1075                 config->input_justification = ADV7511_INPUT_JUSTIFICATION_LEFT;
1076         }
1077
1078         of_property_read_u32(np, "adi,clock-delay", &config->clock_delay);
1079         if (config->clock_delay < -1200 || config->clock_delay > 1600)
1080                 return -EINVAL;
1081
1082         config->embedded_sync = of_property_read_bool(np, "adi,embedded-sync");
1083
1084         /* Hardcode the sync pulse configurations for now. */
1085         config->sync_pulse = ADV7511_INPUT_SYNC_PULSE_NONE;
1086         config->vsync_polarity = ADV7511_SYNC_POLARITY_PASSTHROUGH;
1087         config->hsync_polarity = ADV7511_SYNC_POLARITY_PASSTHROUGH;
1088
1089         return 0;
1090 }
1091
1092 static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
1093 {
1094         struct adv7511_link_config link_config;
1095         struct adv7511 *adv7511;
1096         struct device *dev = &i2c->dev;
1097         unsigned int val;
1098         int ret;
1099
1100         if (!dev->of_node)
1101                 return -EINVAL;
1102
1103         adv7511 = devm_kzalloc(dev, sizeof(*adv7511), GFP_KERNEL);
1104         if (!adv7511)
1105                 return -ENOMEM;
1106
1107         adv7511->i2c_main = i2c;
1108         adv7511->powered = false;
1109         adv7511->status = connector_status_disconnected;
1110
1111         if (dev->of_node)
1112                 adv7511->type = (enum adv7511_type)of_device_get_match_data(dev);
1113         else
1114                 adv7511->type = id->driver_data;
1115
1116         memset(&link_config, 0, sizeof(link_config));
1117
1118         if (adv7511->type == ADV7511)
1119                 ret = adv7511_parse_dt(dev->of_node, &link_config);
1120         else
1121                 ret = adv7533_parse_dt(dev->of_node, adv7511);
1122         if (ret)
1123                 return ret;
1124
1125         ret = adv7511_init_regulators(adv7511);
1126         if (ret) {
1127                 dev_err(dev, "failed to init regulators\n");
1128                 return ret;
1129         }
1130
1131         /*
1132          * The power down GPIO is optional. If present, toggle it from active to
1133          * inactive to wake up the encoder.
1134          */
1135         adv7511->gpio_pd = devm_gpiod_get_optional(dev, "pd", GPIOD_OUT_HIGH);
1136         if (IS_ERR(adv7511->gpio_pd)) {
1137                 ret = PTR_ERR(adv7511->gpio_pd);
1138                 goto uninit_regulators;
1139         }
1140
1141         if (adv7511->gpio_pd) {
1142                 usleep_range(5000, 6000);
1143                 gpiod_set_value_cansleep(adv7511->gpio_pd, 0);
1144         }
1145
1146         adv7511->regmap = devm_regmap_init_i2c(i2c, &adv7511_regmap_config);
1147         if (IS_ERR(adv7511->regmap)) {
1148                 ret = PTR_ERR(adv7511->regmap);
1149                 goto uninit_regulators;
1150         }
1151
1152         ret = regmap_read(adv7511->regmap, ADV7511_REG_CHIP_REVISION, &val);
1153         if (ret)
1154                 goto uninit_regulators;
1155         dev_dbg(dev, "Rev. %d\n", val);
1156
1157         if (adv7511->type == ADV7511)
1158                 ret = regmap_register_patch(adv7511->regmap,
1159                                             adv7511_fixed_registers,
1160                                             ARRAY_SIZE(adv7511_fixed_registers));
1161         else
1162                 ret = adv7533_patch_registers(adv7511);
1163         if (ret)
1164                 goto uninit_regulators;
1165
1166         adv7511_packet_disable(adv7511, 0xffff);
1167
1168         adv7511->i2c_edid = i2c_new_secondary_device(i2c, "edid",
1169                                         ADV7511_EDID_I2C_ADDR_DEFAULT);
1170         if (!adv7511->i2c_edid) {
1171                 ret = -EINVAL;
1172                 goto uninit_regulators;
1173         }
1174
1175         regmap_write(adv7511->regmap, ADV7511_REG_EDID_I2C_ADDR,
1176                      adv7511->i2c_edid->addr << 1);
1177
1178         adv7511->i2c_packet = i2c_new_secondary_device(i2c, "packet",
1179                                         ADV7511_PACKET_I2C_ADDR_DEFAULT);
1180         if (!adv7511->i2c_packet) {
1181                 ret = -EINVAL;
1182                 goto err_i2c_unregister_edid;
1183         }
1184
1185         regmap_write(adv7511->regmap, ADV7511_REG_PACKET_I2C_ADDR,
1186                      adv7511->i2c_packet->addr << 1);
1187
1188         ret = adv7511_init_cec_regmap(adv7511);
1189         if (ret)
1190                 goto err_i2c_unregister_packet;
1191
1192         regmap_write(adv7511->regmap, ADV7511_REG_CEC_I2C_ADDR,
1193                      adv7511->i2c_cec->addr << 1);
1194
1195         INIT_WORK(&adv7511->hpd_work, adv7511_hpd_work);
1196
1197         if (i2c->irq) {
1198                 init_waitqueue_head(&adv7511->wq);
1199
1200                 ret = devm_request_threaded_irq(dev, i2c->irq, NULL,
1201                                                 adv7511_irq_handler,
1202                                                 IRQF_ONESHOT, dev_name(dev),
1203                                                 adv7511);
1204                 if (ret)
1205                         goto err_unregister_cec;
1206         }
1207
1208         adv7511_power_off(adv7511);
1209
1210         i2c_set_clientdata(i2c, adv7511);
1211
1212         if (adv7511->type == ADV7511)
1213                 adv7511_set_link_config(adv7511, &link_config);
1214
1215         ret = adv7511_cec_init(dev, adv7511);
1216         if (ret)
1217                 goto err_unregister_cec;
1218
1219         adv7511->bridge.funcs = &adv7511_bridge_funcs;
1220         adv7511->bridge.of_node = dev->of_node;
1221
1222         drm_bridge_add(&adv7511->bridge);
1223
1224         adv7511_audio_init(dev, adv7511);
1225         return 0;
1226
1227 err_unregister_cec:
1228         i2c_unregister_device(adv7511->i2c_cec);
1229         if (adv7511->cec_clk)
1230                 clk_disable_unprepare(adv7511->cec_clk);
1231 err_i2c_unregister_packet:
1232         i2c_unregister_device(adv7511->i2c_packet);
1233 err_i2c_unregister_edid:
1234         i2c_unregister_device(adv7511->i2c_edid);
1235 uninit_regulators:
1236         adv7511_uninit_regulators(adv7511);
1237
1238         return ret;
1239 }
1240
1241 static int adv7511_remove(struct i2c_client *i2c)
1242 {
1243         struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
1244
1245         if (adv7511->type == ADV7533)
1246                 adv7533_detach_dsi(adv7511);
1247         i2c_unregister_device(adv7511->i2c_cec);
1248         if (adv7511->cec_clk)
1249                 clk_disable_unprepare(adv7511->cec_clk);
1250
1251         adv7511_uninit_regulators(adv7511);
1252
1253         drm_bridge_remove(&adv7511->bridge);
1254
1255         adv7511_audio_exit(adv7511);
1256
1257         cec_unregister_adapter(adv7511->cec_adap);
1258
1259         i2c_unregister_device(adv7511->i2c_packet);
1260         i2c_unregister_device(adv7511->i2c_edid);
1261
1262         return 0;
1263 }
1264
1265 static const struct i2c_device_id adv7511_i2c_ids[] = {
1266         { "adv7511", ADV7511 },
1267         { "adv7511w", ADV7511 },
1268         { "adv7513", ADV7511 },
1269 #ifdef CONFIG_DRM_I2C_ADV7533
1270         { "adv7533", ADV7533 },
1271 #endif
1272         { }
1273 };
1274 MODULE_DEVICE_TABLE(i2c, adv7511_i2c_ids);
1275
1276 static const struct of_device_id adv7511_of_ids[] = {
1277         { .compatible = "adi,adv7511", .data = (void *)ADV7511 },
1278         { .compatible = "adi,adv7511w", .data = (void *)ADV7511 },
1279         { .compatible = "adi,adv7513", .data = (void *)ADV7511 },
1280 #ifdef CONFIG_DRM_I2C_ADV7533
1281         { .compatible = "adi,adv7533", .data = (void *)ADV7533 },
1282 #endif
1283         { }
1284 };
1285 MODULE_DEVICE_TABLE(of, adv7511_of_ids);
1286
1287 static struct mipi_dsi_driver adv7533_dsi_driver = {
1288         .driver.name = "adv7533",
1289 };
1290
1291 static struct i2c_driver adv7511_driver = {
1292         .driver = {
1293                 .name = "adv7511",
1294                 .of_match_table = adv7511_of_ids,
1295         },
1296         .id_table = adv7511_i2c_ids,
1297         .probe = adv7511_probe,
1298         .remove = adv7511_remove,
1299 };
1300
1301 static int __init adv7511_init(void)
1302 {
1303         if (IS_ENABLED(CONFIG_DRM_MIPI_DSI))
1304                 mipi_dsi_driver_register(&adv7533_dsi_driver);
1305
1306         return i2c_add_driver(&adv7511_driver);
1307 }
1308 module_init(adv7511_init);
1309
1310 static void __exit adv7511_exit(void)
1311 {
1312         i2c_del_driver(&adv7511_driver);
1313
1314         if (IS_ENABLED(CONFIG_DRM_MIPI_DSI))
1315                 mipi_dsi_driver_unregister(&adv7533_dsi_driver);
1316 }
1317 module_exit(adv7511_exit);
1318
1319 MODULE_AUTHOR("Lars-Peter Clausen <lars@metafoo.de>");
1320 MODULE_DESCRIPTION("ADV7511 HDMI transmitter driver");
1321 MODULE_LICENSE("GPL");