2 * Copyright 2013 Freescale Semiconductor, Inc.
4 * SPDX-License-Identifier: GPL-2.0+
12 * The environment variables are written to just after the u-boot image
13 * on SDCard, so we must read the MBR to get the start address and code
14 * length of the u-boot image, then calculate the address of the env.
16 #define ESDHC_BOOT_IMAGE_SIZE 0x48
17 #define ESDHC_BOOT_IMAGE_ADDR 0x50
18 #define MBRDBR_BOOT_SIG_55 0x1fe
19 #define MBRDBR_BOOT_SIG_AA 0x1ff
20 #define CONFIG_CFG_DATA_SECTOR 0
23 * The main entry for mmc booting. It's necessary that SDRAM is already
24 * configured and available since this code loads the main U-Boot image
25 * from mmc into SDRAM and starts it from there.
28 void __noreturn
mmc_boot(void)
30 __attribute__((noreturn
)) void (*uboot
)(void);
31 uint blk_start
, blk_cnt
, err
;
39 mmc
= find_mmc_device(0);
41 puts("spl: mmc device not found!!\n");
45 #ifdef CONFIG_FSL_CORENET
46 offset
= CONFIG_SYS_MMC_U_BOOT_OFFS
;
47 code_len
= CONFIG_SYS_MMC_U_BOOT_SIZE
;
49 blklen
= mmc
->read_bl_len
;
50 tmp_buf
= malloc(blklen
);
52 puts("spl: malloc memory failed!!\n");
55 memset(tmp_buf
, 0, blklen
);
58 * Read source addr from sd card
60 err
= mmc
->block_dev
.block_read(0, CONFIG_CFG_DATA_SECTOR
, 1, tmp_buf
);
62 puts("spl: mmc read failed!!\n");
67 val
= *(tmp_buf
+ MBRDBR_BOOT_SIG_55
);
69 puts("spl: mmc signature is not valid!!\n");
73 val
= *(tmp_buf
+ MBRDBR_BOOT_SIG_AA
);
75 puts("spl: mmc signature is not valid!!\n");
82 for (i
= 0; i
< byte_num
; i
++) {
83 val
= *(tmp_buf
+ ESDHC_BOOT_IMAGE_ADDR
+ i
);
84 offset
= (offset
<< 8) + val
;
86 offset
+= CONFIG_SYS_MMC_U_BOOT_OFFS
;
87 /* Get the code size from offset 0x48 */
90 for (i
= 0; i
< byte_num
; i
++) {
91 val
= *(tmp_buf
+ ESDHC_BOOT_IMAGE_SIZE
+ i
);
92 code_len
= (code_len
<< 8) + val
;
94 code_len
-= CONFIG_SYS_MMC_U_BOOT_OFFS
;
96 * Load U-Boot image from mmc into RAM
99 blk_start
= ALIGN(offset
, mmc
->read_bl_len
) / mmc
->read_bl_len
;
100 blk_cnt
= ALIGN(code_len
, mmc
->read_bl_len
) / mmc
->read_bl_len
;
101 err
= mmc
->block_dev
.block_read(0, blk_start
, blk_cnt
,
102 (uchar
*)CONFIG_SYS_MMC_U_BOOT_DST
);
103 if (err
!= blk_cnt
) {
104 puts("spl: mmc read failed!!\n");
110 * Clean d-cache and invalidate i-cache, to
111 * make sure that no stale data is executed.
113 flush_cache(CONFIG_SYS_MMC_U_BOOT_DST
, CONFIG_SYS_MMC_U_BOOT_SIZE
);
116 * Jump to U-Boot image
118 uboot
= (void *)CONFIG_SYS_MMC_U_BOOT_START
;