drivers/net/Kconfig

   1 source "drivers/net/phy/Kconfig"
   2
   3 config DM_ETH
   4         bool "Enable Driver Model for Ethernet drivers"
   5         depends on DM
   6         help
   7           Enable driver model for Ethernet.
   8
   9           The eth_*() interface will be implemented by the UC_ETH class
  10           This is currently implemented in net/eth.c
  11           Look in include/net.h for details.
  12
  13 menuconfig NETDEVICES
  14         bool "Network device support"
  15         depends on NET
  16         default y if DM_ETH
  17         help
  18           You must select Y to enable any network device support
  19           Generally if you have any networking support this is a given
  20
  21           If unsure, say Y
  22
  23 if NETDEVICES
  24
  25 config PHY_GIGE
  26         bool "Enable GbE PHY status parsing and configuration"
  27         help
  28           Enables support for parsing the status output and for
  29           configuring GbE PHYs (affects the inner workings of some
  30           commands and miiphyutil.c).
  31
  32 config AG7XXX
  33         bool "Atheros AG7xxx Ethernet MAC support"
  34         depends on DM_ETH && ARCH_ATH79
  35         select PHYLIB
  36         help
  37           This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is
  38           present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips.
  39
  40
  41 config ALTERA_TSE
  42         bool "Altera Triple-Speed Ethernet MAC support"
  43         depends on DM_ETH
  44         select PHYLIB
  45         help
  46           This driver supports the Altera Triple-Speed (TSE) Ethernet MAC.
  47           Please find details on the "Triple-Speed Ethernet MegaCore Function
  48           Resource Center" of Altera.
  49
  50 config BCM_SF2_ETH
  51         bool "Broadcom SF2 (Starfighter2) Ethernet support"
  52         select PHYLIB
  53         help
  54           This is an abstract framework which provides a generic interface
  55           to MAC and DMA management for multiple Broadcom SoCs such as
  56           Cygnus, NSP and bcm28155_ap platforms.
  57
  58 config BCM_SF2_ETH_DEFAULT_PORT
  59         int "Broadcom SF2 (Starfighter2) Ethernet default port number"
  60         depends on BCM_SF2_ETH
  61         default 0
  62         help
  63           Default port number for the Starfighter2 ethernet driver.
  64
  65 config BCM_SF2_ETH_GMAC
  66         bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support"
  67         depends on BCM_SF2_ETH
  68         help
  69           This flag enables the ethernet support for Broadcom platforms with
  70           GMAC such as Cygnus. This driver is based on the framework provided
  71           by the BCM_SF2_ETH driver.
  72           Say Y to any bcmcygnus based platforms.
  73
  74 config DWC_ETH_QOS
  75         bool "Synopsys DWC Ethernet QOS device support"
  76         depends on DM_ETH
  77         select PHYLIB
  78         help
  79           This driver supports the Synopsys Designware Ethernet QOS (Quality
  80           Of Service) IP block. The IP supports many options for bus type,
  81           clocking/reset structure, and feature list. This driver currently
  82           supports the specific configuration used in NVIDIA's Tegra186 chip,
  83           but should be extensible to other combinations quite easily.
  84
  85 config E1000
  86         bool "Intel PRO/1000 Gigabit Ethernet support"
  87         help
  88           This driver supports Intel(R) PRO/1000 gigabit ethernet family of
  89           adapters.  For more information on how to identify your adapter, go
  90           to the Adapter & Driver ID Guide at:
  91
  92           <http://support.intel.com/support/network/adapter/pro100/21397.htm>
  93
  94 config E1000_SPI_GENERIC
  95         bool "Allow access to the Intel 8257x SPI bus"
  96         depends on E1000
  97         help
  98           Allow generic access to the SPI bus on the Intel 8257x, for
  99           example with the "sspi" command.
 100
 101 config E1000_SPI
 102         bool "Enable SPI bus utility code"
 103         depends on E1000
 104         help
 105           Utility code for direct access to the SPI bus on Intel 8257x.
 106           This does not do anything useful unless you set at least one
 107           of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
 108
 109 config CMD_E1000
 110         bool "Enable the e1000 command"
 111         depends on E1000
 112         help
 113           This enables the 'e1000' management command for E1000 devices. When
 114           used on devices with SPI support you can reprogram the EEPROM from
 115           U-Boot.
 116
 117 config ETH_SANDBOX
 118         depends on DM_ETH && SANDBOX
 119         default y
 120         bool "Sandbox: Mocked Ethernet driver"
 121         help
 122           This driver simply responds with fake ARP replies and ping
 123           replies that are used to verify network stack functionality
 124
 125           This driver is particularly useful in the test/dm/eth.c tests
 126
 127 config ETH_SANDBOX_RAW
 128         depends on DM_ETH && SANDBOX
 129         default y
 130         bool "Sandbox: Bridge to Linux Raw Sockets"
 131         help
 132           This driver is a bridge from the bottom of the network stack
 133           in U-Boot to the RAW AF_PACKET API in Linux. This allows real
 134           network traffic to be tested from within sandbox. See
 135           board/sandbox/README.sandbox for more details.
 136
 137 config ETH_DESIGNWARE
 138         bool "Synopsys Designware Ethernet MAC"
 139         select PHYLIB
 140         help
 141           This MAC is present in SoCs from various vendors. It supports
 142           100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to
 143           provide the PHY (physical media interface).
 144
 145 config ETHOC
 146         bool "OpenCores 10/100 Mbps Ethernet MAC"
 147         help
 148           This MAC is present in OpenRISC and Xtensa XTFPGA boards.
 149
 150 config FEC_MXC
 151         bool "FEC Ethernet controller"
 152         depends on MX5 || MX6
 153         help
 154           This driver supports the 10/100 Fast Ethernet controller for
 155           NXP i.MX processors.
 156
 157 config FTMAC100
 158         bool "Ftmac100 Ethernet Support"
 159         help
 160           This MAC is present in Andestech SoCs.
 161
 162 config MVNETA
 163         bool "Marvell Armada 385 network interface support"
 164         depends on ARMADA_XP || ARMADA_38X
 165         select PHYLIB
 166         help
 167           This driver supports the network interface units in the
 168           Marvell ARMADA XP and 38X SoCs
 169
 170 config MVPP2
 171         bool "Marvell Armada 375/7K/8K network interface support"
 172         depends on ARMADA_375 || ARMADA_8K
 173         select PHYLIB
 174         help
 175           This driver supports the network interface units in the
 176           Marvell ARMADA 375, 7K and 8K SoCs.
 177
 178 config MACB
 179         bool "Cadence MACB/GEM Ethernet Interface"
 180         depends on DM_ETH
 181         select PHYLIB
 182         help
 183           The Cadence MACB ethernet interface is found on many Atmel
 184           AT91 and SAMA5 parts.  This driver also supports the Cadence
 185           GEM (Gigabit Ethernet MAC) found in some ARM SoC devices.
 186           Say Y to include support for the MACB/GEM chip.
 187
 188 config PCH_GBE
 189         bool "Intel Platform Controller Hub EG20T GMAC driver"
 190         depends on DM_ETH && DM_PCI
 191         select PHYLIB
 192         help
 193           This MAC is present in Intel Platform Controller Hub EG20T. It
 194           supports 10/100/1000 Mbps operation.
 195
 196 config RGMII
 197         bool "Enable RGMII"
 198         help
 199           Enable the support of the Reduced Gigabit Media-Independent
 200           Interface (RGMII).
 201
 202 config RTL8139
 203         bool "Realtek 8139 series Ethernet controller driver"
 204         help
 205           This driver supports Realtek 8139 series fast ethernet family of
 206           PCI chipsets/adapters.
 207
 208 config RTL8169
 209         bool "Realtek 8169 series Ethernet controller driver"
 210         help
 211           This driver supports Realtek 8169 series gigabit ethernet family of
 212           PCI/PCIe chipsets/adapters.
 213
 214 config SMC911X
 215         bool "SMSC LAN911x and LAN921x controller driver"
 216
 217 if SMC911X
 218
 219 config SMC911X_BASE
 220         hex "SMC911X Base Address"
 221         help
 222           Define this to hold the physical address
 223           of the device (I/O space)
 224
 225 choice
 226         prompt "SMC911X bus width"
 227         default SMC911X_16_BIT
 228
 229 config SMC911X_32_BIT
 230         bool "Enable 32-bit interface"
 231
 232 config SMC911X_16_BIT
 233         bool "Enable 16-bit interface"
 234         help
 235           Define this if data bus is 16 bits. If your processor
 236           automatically converts one 32 bit word to two 16 bit
 237           words you may also try CONFIG_SMC911X_32_BIT.
 238
 239 endchoice
 240 endif #SMC911X
 241
 242 config SUN7I_GMAC
 243         bool "Enable Allwinner GMAC Ethernet support"
 244         help
 245           Enable the support for Sun7i GMAC Ethernet controller
 246
 247 config SUN4I_EMAC
 248         bool "Allwinner Sun4i Ethernet MAC support"
 249         depends on DM_ETH
 250         select PHYLIB
 251         help
 252           This driver supports the Allwinner based SUN4I Ethernet MAC.
 253
 254 config SUN8I_EMAC
 255         bool "Allwinner Sun8i Ethernet MAC support"
 256         depends on DM_ETH
 257         select PHYLIB
 258         select PHY_GIGE
 259         help
 260           This driver supports the  Allwinner based SUN8I/SUN50I Ethernet MAC.
 261           It can be found in H3/A64/A83T based SoCs and compatible with both
 262           External and Internal PHYs.
 263
 264 config XILINX_AXIEMAC
 265         depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP)
 266         select PHYLIB
 267         select MII
 268         bool "Xilinx AXI Ethernet"
 269         help
 270           This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
 271
 272 config XILINX_EMACLITE
 273         depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS)
 274         select PHYLIB
 275         select MII
 276         bool "Xilinx Ethernetlite"
 277         help
 278           This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs.
 279
 280 config ZYNQ_GEM
 281         depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP)
 282         select PHYLIB
 283         bool "Xilinx Ethernet GEM"
 284         help
 285           This MAC is present in Xilinx Zynq and ZynqMP SoCs.
 286
 287 config PIC32_ETH
 288         bool "Microchip PIC32 Ethernet Support"
 289         depends on DM_ETH && MACH_PIC32
 290         select PHYLIB
 291         help
 292           This driver implements 10/100 Mbps Ethernet and MAC layer for
 293           Microchip PIC32 microcontrollers.
 294
 295 config GMAC_ROCKCHIP
 296         bool "Rockchip Synopsys Designware Ethernet MAC"
 297         depends on DM_ETH && ETH_DESIGNWARE
 298         help
 299           This driver provides Rockchip SoCs network support based on the
 300           Synopsys Designware driver.
 301
 302 config RENESAS_RAVB
 303         bool "Renesas Ethernet AVB MAC"
 304         depends on DM_ETH && RCAR_GEN3
 305         select PHYLIB
 306         help
 307           This driver implements support for the Ethernet AVB block in
 308           Renesas M3 and H3 SoCs.
 309
 310 config MPC8XX_FEC
 311         bool "Fast Ethernet Controller on MPC8XX"
 312         depends on 8xx
 313         select MII
 314         help
 315           This driver implements support for the Fast Ethernet Controller
 316           on MPC8XX
 317
 318 config ETHER_ON_FEC1
 319         bool "FEC1"
 320         depends on MPC8XX_FEC
 321         default y
 322
 323 config FEC1_PHY
 324         int "FEC1 PHY"
 325         depends on ETHER_ON_FEC1
 326         default -1
 327         help
 328           Define to the hardcoded PHY address which corresponds
 329           to the given FEC; i. e.
 330                 #define CONFIG_FEC1_PHY 4
 331           means that the PHY with address 4 is connected to FEC1
 332
 333           When set to -1, means to probe for first available.
 334
 335 config PHY_NORXERR
 336         bool "PHY_NORXERR"
 337         depends on ETHER_ON_FEC1
 338         default n
 339         help
 340           The PHY does not have a RXERR line (RMII only).
 341           (so program the FEC to ignore it).
 342
 343 config ETHER_ON_FEC2
 344         bool "FEC2"
 345         depends on MPC8XX_FEC && MPC885
 346         default y
 347
 348 config FEC2_PHY
 349         int "FEC2 PHY"
 350         depends on ETHER_ON_FEC2
 351         default -1
 352         help
 353           Define to the hardcoded PHY address which corresponds
 354           to the given FEC; i. e.
 355                 #define CONFIG_FEC1_PHY 4
 356           means that the PHY with address 4 is connected to FEC1
 357
 358           When set to -1, means to probe for first available.
 359
 360 config FEC2_PHY_NORXERR
 361         bool "PHY_NORXERR"
 362         depends on ETHER_ON_FEC2
 363         default n
 364         help
 365           The PHY does not have a RXERR line (RMII only).
 366           (so program the FEC to ignore it).
 367
 368 endif # NETDEVICES