drivers/net/ethernet/ti/Kconfig

   1 # SPDX-License-Identifier: GPL-2.0-only
   2 #
   3 # TI device configuration
   4 #
   5
   6 config NET_VENDOR_TI
   7         bool "Texas Instruments (TI) devices"
   8         default y
   9         depends on PCI || EISA || AR7 || ARCH_DAVINCI || ARCH_OMAP2PLUS || ARCH_KEYSTONE || ARCH_K3
  10         ---help---
  11           If you have a network (Ethernet) card belonging to this class, say Y.
  12
  13           Note that the answer to this question doesn't directly affect the
  14           kernel: saying N will just cause the configurator to skip all
  15           the questions about TI devices. If you say Y, you will be asked for
  16           your specific card in the following questions.
  17
  18 if NET_VENDOR_TI
  19
  20 config TI_DAVINCI_EMAC
  21         tristate "TI DaVinci EMAC Support"
  22         depends on ARM && ( ARCH_DAVINCI || ARCH_OMAP3 ) || COMPILE_TEST
  23         select TI_DAVINCI_MDIO
  24         select PHYLIB
  25         select GENERIC_ALLOCATOR
  26         ---help---
  27           This driver supports TI's DaVinci Ethernet .
  28
  29           To compile this driver as a module, choose M here: the module
  30           will be called davinci_emac_driver.  This is recommended.
  31
  32 config TI_DAVINCI_MDIO
  33         tristate "TI DaVinci MDIO Support"
  34         depends on ARCH_DAVINCI || ARCH_OMAP2PLUS || ARCH_KEYSTONE || ARCH_K3 || COMPILE_TEST
  35         select PHYLIB
  36         ---help---
  37           This driver supports TI's DaVinci MDIO module.
  38
  39           To compile this driver as a module, choose M here: the module
  40           will be called davinci_mdio.  This is recommended.
  41
  42 config TI_CPSW_PHY_SEL
  43         bool "TI CPSW Phy mode Selection (DEPRECATED)"
  44         default n
  45         ---help---
  46           This driver supports configuring of the phy mode connected to
  47           the CPSW. DEPRECATED: use PHY_TI_GMII_SEL.
  48
  49 config TI_CPSW
  50         tristate "TI CPSW Switch Support"
  51         depends on ARCH_DAVINCI || ARCH_OMAP2PLUS || COMPILE_TEST
  52         select TI_DAVINCI_MDIO
  53         select MFD_SYSCON
  54         select PAGE_POOL
  55         select REGMAP
  56         imply PHY_TI_GMII_SEL
  57         ---help---
  58           This driver supports TI's CPSW Ethernet Switch.
  59
  60           To compile this driver as a module, choose M here: the module
  61           will be called cpsw.
  62
  63 config TI_CPSW_SWITCHDEV
  64         tristate "TI CPSW Switch Support with switchdev"
  65         depends on ARCH_DAVINCI || ARCH_OMAP2PLUS || COMPILE_TEST
  66         depends on NET_SWITCHDEV
  67         select PAGE_POOL
  68         select TI_DAVINCI_MDIO
  69         select MFD_SYSCON
  70         select REGMAP
  71         select NET_DEVLINK
  72         imply PHY_TI_GMII_SEL
  73         help
  74           This driver supports TI's CPSW Ethernet Switch.
  75
  76           To compile this driver as a module, choose M here: the module
  77           will be called cpsw_new.
  78
  79 config TI_CPTS
  80         bool "TI Common Platform Time Sync (CPTS) Support"
  81         depends on TI_CPSW || TI_KEYSTONE_NETCP || TI_CPSW_SWITCHDEV || COMPILE_TEST
  82         depends on COMMON_CLK
  83         depends on POSIX_TIMERS
  84         ---help---
  85           This driver supports the Common Platform Time Sync unit of
  86           the CPSW Ethernet Switch and Keystone 2 1g/10g Switch Subsystem.
  87           The unit can time stamp PTP UDP/IPv4 and Layer 2 packets, and the
  88           driver offers a PTP Hardware Clock.
  89
  90 config TI_CPTS_MOD
  91         tristate
  92         depends on TI_CPTS
  93         default y if TI_CPSW=y || TI_KEYSTONE_NETCP=y || TI_CPSW_SWITCHDEV=y
  94         select NET_PTP_CLASSIFY
  95         imply PTP_1588_CLOCK
  96         default m
  97
  98 config TI_K3_AM65_CPSW_NUSS
  99         tristate "TI K3 AM654x/J721E CPSW Ethernet driver"
 100         depends on ARCH_K3 && OF && TI_K3_UDMA_GLUE_LAYER
 101         select TI_DAVINCI_MDIO
 102         imply PHY_TI_GMII_SEL
 103         help
 104           This driver supports TI K3 AM654/J721E CPSW2G Ethernet SubSystem.
 105           The two-port Gigabit Ethernet MAC (MCU_CPSW0) subsystem provides
 106           Ethernet packet communication for the device: One Ethernet port
 107           (port 1) with selectable RGMII and RMII interfaces and an internal
 108           Communications Port Programming Interface (CPPI) port (port 0).
 109
 110           To compile this driver as a module, choose M here: the module
 111           will be called ti-am65-cpsw-nuss.
 112
 113 config TI_KEYSTONE_NETCP
 114         tristate "TI Keystone NETCP Core Support"
 115         select TI_DAVINCI_MDIO
 116         depends on OF
 117         depends on KEYSTONE_NAVIGATOR_DMA && KEYSTONE_NAVIGATOR_QMSS
 118         ---help---
 119           This driver supports TI's Keystone NETCP Core.
 120
 121           To compile this driver as a module, choose M here: the module
 122           will be called keystone_netcp.
 123
 124 config TI_KEYSTONE_NETCP_ETHSS
 125         depends on TI_KEYSTONE_NETCP
 126         tristate "TI Keystone NETCP Ethernet subsystem Support"
 127         ---help---
 128
 129           To compile this driver as a module, choose M here: the module
 130           will be called keystone_netcp_ethss.
 131
 132 config TLAN
 133         tristate "TI ThunderLAN support"
 134         depends on (PCI || EISA)
 135         ---help---
 136           If you have a PCI Ethernet network card based on the ThunderLAN chip
 137           which is supported by this driver, say Y here.
 138
 139           Devices currently supported by this driver are Compaq Netelligent,
 140           Compaq NetFlex and Olicom cards.  Please read the file
 141           <file:Documentation/networking/device_drivers/ti/tlan.txt>
 142           for more details.
 143
 144           To compile this driver as a module, choose M here. The module
 145           will be called tlan.
 146
 147           Please email feedback to <torben.mathiasen@compaq.com>.
 148
 149 config CPMAC
 150         tristate "TI AR7 CPMAC Ethernet support"
 151         depends on AR7
 152         select PHYLIB
 153         ---help---
 154           TI AR7 CPMAC Ethernet support
 155
 156 endif # NET_VENDOR_TI