drivers/power/Kconfig

   1 menu "Power"
   2
   3 source "drivers/power/domain/Kconfig"
   4
   5 source "drivers/power/pmic/Kconfig"
   6
   7 source "drivers/power/regulator/Kconfig"
   8
   9 choice
  10         prompt "Select Sunxi PMIC Variant"
  11         depends on ARCH_SUNXI
  12         default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
  13         default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40
  14         default AXP818_POWER if MACH_SUN8I_A83T
  15         default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I
  16
  17 config SUNXI_NO_PMIC
  18         bool "board without a pmic"
  19         ---help---
  20         Select this for boards which do not use a PMIC.
  21
  22 config AXP152_POWER
  23         bool "axp152 pmic support"
  24         depends on MACH_SUN5I
  25         select CMD_POWEROFF
  26         ---help---
  27         Select this to enable support for the axp152 pmic found on most
  28         A10s boards.
  29
  30 config AXP209_POWER
  31         bool "axp209 pmic support"
  32         depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
  33         select CMD_POWEROFF
  34         ---help---
  35         Select this to enable support for the axp209 pmic found on most
  36         A10, A13 and A20 boards.
  37
  38 config AXP221_POWER
  39         bool "axp221 / axp223 pmic support"
  40         depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40
  41         select CMD_POWEROFF
  42         ---help---
  43         Select this to enable support for the axp221/axp223 pmic found on most
  44         A23 and A31 boards.
  45
  46 config AXP809_POWER
  47         bool "axp809 pmic support"
  48         depends on MACH_SUN9I
  49         select CMD_POWEROFF
  50         ---help---
  51         Say y here to enable support for the axp809 pmic found on A80 boards.
  52
  53 config AXP818_POWER
  54         bool "axp818 pmic support"
  55         depends on MACH_SUN8I_A83T
  56         select CMD_POWEROFF
  57         ---help---
  58         Say y here to enable support for the axp818 pmic found on
  59         A83T dev board.
  60
  61 config SY8106A_POWER
  62         bool "SY8106A pmic support"
  63         depends on MACH_SUNXI_H3_H5
  64         ---help---
  65         Select this to enable support for the SY8106A pmic found on some
  66         H3 boards.
  67
  68 endchoice
  69
  70 config AXP_DCDC1_VOLT
  71         int "axp pmic dcdc1 voltage"
  72         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
  73         default 3300 if AXP818_POWER || MACH_SUN8I_R40
  74         default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
  75         ---help---
  76         Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to
  77         disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for
  78         generic 3.3V IO voltage for external devices like the lcd-panal and
  79         sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to
  80         save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T
  81         dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally
  82         powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG.
  83
  84 config AXP_DCDC2_VOLT
  85         int "axp pmic dcdc2 voltage"
  86         depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
  87         default 900 if AXP818_POWER
  88         default 1400 if AXP152_POWER || AXP209_POWER
  89         default 1200 if MACH_SUN6I
  90         default 1100 if MACH_SUN8I
  91         default 0 if MACH_SUN9I
  92         ---help---
  93         Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to
  94         disable dcdc2.
  95         On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V.
  96         On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V.
  97         On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V.
  98         On A80 boards dcdc2 powers the GPU and can be left off.
  99         On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
 100         On R40 boards dcdc2 is VDD-CPU and should be 1.1V
 101
 102 config AXP_DCDC3_VOLT
 103         int "axp pmic dcdc3 voltage"
 104         depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
 105         default 900 if AXP809_POWER || AXP818_POWER
 106         default 1500 if AXP152_POWER
 107         default 1250 if AXP209_POWER
 108         default 1100 if MACH_SUN8I_R40
 109         default 1200 if MACH_SUN6I || MACH_SUN8I
 110         ---help---
 111         Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to
 112         disable dcdc3.
 113         On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and
 114         should be 1.25V.
 115         On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V.
 116         On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V.
 117         On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
 118         On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
 119         On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V.
 120
 121 config AXP_DCDC4_VOLT
 122         int "axp pmic dcdc4 voltage"
 123         depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
 124         default 1250 if AXP152_POWER
 125         default 1200 if MACH_SUN6I
 126         default 0 if MACH_SUN8I
 127         default 900 if MACH_SUN9I
 128         ---help---
 129         Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to
 130         disable dcdc4.
 131         On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V.
 132         On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V.
 133         On A23 / A33 boards dcdc4 is unused and should be disabled.
 134         On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V.
 135         On A83T boards dcdc4 is used for VDD-GPU.
 136
 137 config AXP_DCDC5_VOLT
 138         int "axp pmic dcdc5 voltage"
 139         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 140         default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
 141         ---help---
 142         Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to
 143         disable dcdc5.
 144         On A23 / A31 / A33 / A80 / A83T / R40 boards dcdc5 is VCC-DRAM and
 145         should be 1.5V, 1.35V if DDR3L is used.
 146
 147 config AXP_ALDO1_VOLT
 148         int "axp pmic (a)ldo1 voltage"
 149         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 150         default 0 if MACH_SUN6I || MACH_SUN8I_R40
 151         default 1800 if MACH_SUN8I_A83T
 152         default 3000 if MACH_SUN8I || MACH_SUN9I
 153         ---help---
 154         Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to
 155         disable aldo1.
 156         On A31 boards aldo1 is often used to power the wifi module.
 157         On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V.
 158         On A80 boards aldo1 powers the USB hosts and should be 3.0V.
 159         On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and
 160         should be 1.8V.
 161
 162 config AXP_ALDO2_VOLT
 163         int "axp pmic (a)ldo2 voltage"
 164         depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
 165         default 3000 if AXP152_POWER || AXP209_POWER
 166         default 0 if MACH_SUN6I || MACH_SUN9I
 167         default 1800 if MACH_SUN8I_A83T
 168         default 2500 if MACH_SUN8I
 169         ---help---
 170         Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to
 171         disable aldo2.
 172         On A10(s) / A13 / A20 boards aldo2 is AVCC and should be 3.0V.
 173         On A31 boards aldo2 is typically unused and should be disabled.
 174         On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V.
 175         On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V.
 176         On A80 boards aldo2 powers PB pingroup and camera IO and can be left off.
 177         On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC,
 178         LPDDR2, and the codec. It should be 1.8V.
 179
 180 config AXP_ALDO3_VOLT
 181         int "axp pmic (a)ldo3 voltage"
 182         depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
 183         default 0 if AXP209_POWER || MACH_SUN9I
 184         default 3000 if MACH_SUN6I || MACH_SUN8I
 185         ---help---
 186         Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to
 187         disable aldo3.
 188         On A10(s) / A13 / A20 boards aldo3 should be 2.8V.
 189         On A23 / A31 / A33 / R40 boards aldo3 is VCC-PLL and AVCC and should
 190         be 3.0V.
 191         On A80 boards aldo3 is normally not used.
 192         On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
 193         3.0V.
 194
 195 config AXP_ALDO4_VOLT
 196         int "axp pmic (a)ldo4 voltage"
 197         depends on AXP209_POWER
 198         default 0 if AXP209_POWER
 199         ---help---
 200         Set the voltage (mV) to program the axp pmic aldo4 at, set to 0 to
 201         disable aldo4.
 202         On A10(s) / A13 / A20 boards aldo4 should be 2.8V.
 203
 204 config AXP_DLDO1_VOLT
 205         int "axp pmic dldo1 voltage"
 206         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 207         default 0
 208         ---help---
 209         Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to
 210         disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used
 211         to power the ethernet phy. On A23, A33 and A80 boards this is often
 212         used to power the wifi.
 213
 214 config AXP_DLDO2_VOLT
 215         int "axp pmic dldo2 voltage"
 216         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 217         default 3000 if MACH_SUN9I
 218         default 0
 219         ---help---
 220         Set the voltage (mV) to program the axp pmic dldo2 at, set to 0 to
 221         disable dldo2.
 222         On A80 boards dldo2 normally powers the PL pins and should be 3.0V.
 223
 224 config AXP_DLDO3_VOLT
 225         int "axp pmic dldo3 voltage"
 226         depends on AXP221_POWER || AXP818_POWER
 227         default 0
 228         ---help---
 229         Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to
 230         disable dldo3.
 231
 232 config AXP_DLDO4_VOLT
 233         int "axp pmic dldo4 voltage"
 234         depends on AXP221_POWER || AXP818_POWER
 235         default 0
 236         ---help---
 237         Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to
 238         disable dldo4.
 239
 240 config AXP_ELDO1_VOLT
 241         int "axp pmic eldo1 voltage"
 242         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 243         default 0
 244         ---help---
 245         Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to
 246         disable eldo1.
 247
 248 config AXP_ELDO2_VOLT
 249         int "axp pmic eldo2 voltage"
 250         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 251         default 0
 252         ---help---
 253         Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to
 254         disable eldo2.
 255
 256 config AXP_ELDO3_VOLT
 257         int "axp pmic eldo3 voltage"
 258         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 259         default 3000 if MACH_SUN9I
 260         default 0
 261         ---help---
 262         Set the voltage (mV) to program the axp pmic eldo3 at, set to 0 to
 263         disable eldo3. On some A31(s) tablets it might be used to supply
 264         1.2V for the SSD2828 chip (converter of parallel LCD interface
 265         into MIPI DSI).
 266         On A80 boards it powers the PM pingroup and should be 3.0V.
 267
 268 config AXP_FLDO1_VOLT
 269         int "axp pmic fldo1 voltage"
 270         depends on AXP818_POWER
 271         default 0 if MACH_SUN8I_A83T
 272         ---help---
 273         Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to
 274         disable fldo1.
 275         On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is
 276         used.
 277
 278 config AXP_FLDO2_VOLT
 279         int "axp pmic fldo2 voltage"
 280         depends on AXP818_POWER
 281         default 900 if MACH_SUN8I_A83T
 282         ---help---
 283         Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to
 284         disable fldo2.
 285         On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V.
 286
 287 config AXP_FLDO3_VOLT
 288         int "axp pmic fldo3 voltage"
 289         depends on AXP818_POWER
 290         default 0
 291         ---help---
 292         Set the voltage (mV) to program the axp pmic fldo3 at, set to 0 to
 293         disable fldo3.
 294
 295 config AXP_SW_ON
 296         bool "axp pmic sw on"
 297         depends on AXP809_POWER || AXP818_POWER
 298         default n
 299         ---help---
 300         Enable to turn on axp pmic sw.
 301
 302 config SY8106A_VOUT1_VOLT
 303         int "SY8106A pmic VOUT1 voltage"
 304         depends on SY8106A_POWER
 305         default 1200
 306         ---help---
 307         Set the voltage (mV) to program the SY8106A pmic VOUT1. This
 308         is typically used to power the VDD-CPU and should be 1200mV.
 309         Values can range from 680mV till 1950mV.
 310
 311 config TWL4030_POWER
 312         depends on OMAP34XX
 313         bool "Enable driver for TI TWL4030 power management chip"
 314         imply CMD_POWEROFF
 315         ---help---
 316         The TWL4030 in a combination audio CODEC/power management with
 317         GPIO and it is commonly used with the OMAP3 family of processors
 318
 319 endmenu