drivers/power/Kconfig

   1 menu "Power"
   2
   3 source "drivers/power/pmic/Kconfig"
   4
   5 source "drivers/power/regulator/Kconfig"
   6
   7 choice
   8         prompt "Select Sunxi PMIC Variant"
   9         depends on ARCH_SUNXI
  10         default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
  11         default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
  12         default AXP818_POWER if MACH_SUN8I_A83T
  13         default SUNXI_NO_PMIC if MACH_SUN8I_H3 || MACH_SUN50I
  14
  15 config SUNXI_NO_PMIC
  16         boolean "board without a pmic"
  17         ---help---
  18         Select this for boards which do not use a PMIC.
  19
  20 config AXP152_POWER
  21         boolean "axp152 pmic support"
  22         depends on MACH_SUN5I
  23         select CMD_POWEROFF
  24         ---help---
  25         Select this to enable support for the axp152 pmic found on most
  26         A10s boards.
  27
  28 config AXP209_POWER
  29         boolean "axp209 pmic support"
  30         depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
  31         select CMD_POWEROFF
  32         ---help---
  33         Select this to enable support for the axp209 pmic found on most
  34         A10, A13 and A20 boards.
  35
  36 config AXP221_POWER
  37         boolean "axp221 / axp223 pmic support"
  38         depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
  39         select CMD_POWEROFF
  40         ---help---
  41         Select this to enable support for the axp221/axp223 pmic found on most
  42         A23 and A31 boards.
  43
  44 config AXP809_POWER
  45         boolean "axp809 pmic support"
  46         depends on MACH_SUN9I
  47         select CMD_POWEROFF
  48         ---help---
  49         Say y here to enable support for the axp809 pmic found on A80 boards.
  50
  51 config AXP818_POWER
  52         boolean "axp818 pmic support"
  53         depends on MACH_SUN8I_A83T
  54         select CMD_POWEROFF
  55         ---help---
  56         Say y here to enable support for the axp818 pmic found on
  57         A83T dev board.
  58
  59 config SY8106A_POWER
  60         boolean "SY8106A pmic support"
  61         depends on MACH_SUN8I_H3
  62         ---help---
  63         Select this to enable support for the SY8106A pmic found on some
  64         H3 boards.
  65
  66 endchoice
  67
  68 config AXP_DCDC1_VOLT
  69         int "axp pmic dcdc1 voltage"
  70         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
  71         default 3300 if AXP818_POWER
  72         default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
  73         ---help---
  74         Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to
  75         disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for
  76         generic 3.3V IO voltage for external devices like the lcd-panal and
  77         sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to
  78         save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T
  79         dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally
  80         powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG.
  81
  82 config AXP_DCDC2_VOLT
  83         int "axp pmic dcdc2 voltage"
  84         depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
  85         default 900 if AXP818_POWER
  86         default 1400 if AXP152_POWER || AXP209_POWER
  87         default 1200 if MACH_SUN6I
  88         default 1100 if MACH_SUN8I
  89         default 0 if MACH_SUN9I
  90         ---help---
  91         Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to
  92         disable dcdc2.
  93         On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V.
  94         On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V.
  95         On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V.
  96         On A80 boards dcdc2 powers the GPU and can be left off.
  97         On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
  98
  99 config AXP_DCDC3_VOLT
 100         int "axp pmic dcdc3 voltage"
 101         depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
 102         default 900 if AXP809_POWER || AXP818_POWER
 103         default 1500 if AXP152_POWER
 104         default 1250 if AXP209_POWER
 105         default 1200 if MACH_SUN6I || MACH_SUN8I
 106         ---help---
 107         Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to
 108         disable dcdc3.
 109         On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and
 110         should be 1.25V.
 111         On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V.
 112         On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V.
 113         On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
 114         On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
 115
 116 config AXP_DCDC4_VOLT
 117         int "axp pmic dcdc4 voltage"
 118         depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
 119         default 1250 if AXP152_POWER
 120         default 1200 if MACH_SUN6I
 121         default 0 if MACH_SUN8I
 122         default 900 if MACH_SUN9I
 123         ---help---
 124         Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to
 125         disable dcdc4.
 126         On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V.
 127         On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V.
 128         On A23 / A33 boards dcdc4 is unused and should be disabled.
 129         On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V.
 130         On A83T boards dcdc4 is used for VDD-GPU.
 131
 132 config AXP_DCDC5_VOLT
 133         int "axp pmic dcdc5 voltage"
 134         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 135         default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
 136         ---help---
 137         Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to
 138         disable dcdc5.
 139         On A23 / A31 / A33 / A80 / A83T boards dcdc5 is VCC-DRAM and
 140         should be 1.5V, 1.35V if DDR3L is used.
 141
 142 config AXP_ALDO1_VOLT
 143         int "axp pmic (a)ldo1 voltage"
 144         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 145         default 0 if MACH_SUN6I
 146         default 1800 if MACH_SUN8I_A83T
 147         default 3000 if MACH_SUN8I || MACH_SUN9I
 148         ---help---
 149         Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to
 150         disable aldo1.
 151         On A31 boards aldo1 is often used to power the wifi module.
 152         On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V.
 153         On A80 boards aldo1 powers the USB hosts and should be 3.0V.
 154         On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and
 155         should be 1.8V.
 156
 157 config AXP_ALDO2_VOLT
 158         int "axp pmic (a)ldo2 voltage"
 159         depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
 160         default 3000 if AXP152_POWER || AXP209_POWER
 161         default 0 if MACH_SUN6I || MACH_SUN9I
 162         default 1800 if MACH_SUN8I_A83T
 163         default 2500 if MACH_SUN8I
 164         ---help---
 165         Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to
 166         disable aldo2.
 167         On A10(s) / A13 / A20 boards aldo2 is AVCC and should be 3.0V.
 168         On A31 boards aldo2 is typically unused and should be disabled.
 169         On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V.
 170         On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V.
 171         On A80 boards aldo2 powers PB pingroup and camera IO and can be left off.
 172         On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC,
 173         LPDDR2, and the codec. It should be 1.8V.
 174
 175 config AXP_ALDO3_VOLT
 176         int "axp pmic (a)ldo3 voltage"
 177         depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
 178         default 0 if AXP209_POWER || MACH_SUN9I
 179         default 3000 if MACH_SUN6I || MACH_SUN8I
 180         ---help---
 181         Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to
 182         disable aldo3.
 183         On A10(s) / A13 / A20 boards aldo3 should be 2.8V.
 184         On A23 / A31 / A33 boards aldo3 is VCC-PLL and AVCC and should be 3.0V.
 185         On A80 boards aldo3 is normally not used.
 186         On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
 187         3.0V.
 188
 189 config AXP_ALDO4_VOLT
 190         int "axp pmic (a)ldo4 voltage"
 191         depends on AXP209_POWER
 192         default 0 if AXP209_POWER
 193         ---help---
 194         Set the voltage (mV) to program the axp pmic aldo4 at, set to 0 to
 195         disable aldo4.
 196         On A10(s) / A13 / A20 boards aldo4 should be 2.8V.
 197
 198 config AXP_DLDO1_VOLT
 199         int "axp pmic dldo1 voltage"
 200         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 201         default 0
 202         ---help---
 203         Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to
 204         disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used
 205         to power the ethernet phy. On A23, A33 and A80 boards this is often
 206         used to power the wifi.
 207
 208 config AXP_DLDO2_VOLT
 209         int "axp pmic dldo2 voltage"
 210         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 211         default 3000 if MACH_SUN9I
 212         default 0
 213         ---help---
 214         Set the voltage (mV) to program the axp pmic dldo2 at, set to 0 to
 215         disable dldo2.
 216         On A80 boards dldo2 normally powers the PL pins and should be 3.0V.
 217
 218 config AXP_DLDO3_VOLT
 219         int "axp pmic dldo3 voltage"
 220         depends on AXP221_POWER || AXP818_POWER
 221         default 0
 222         ---help---
 223         Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to
 224         disable dldo3.
 225
 226 config AXP_DLDO4_VOLT
 227         int "axp pmic dldo4 voltage"
 228         depends on AXP221_POWER || AXP818_POWER
 229         default 0
 230         ---help---
 231         Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to
 232         disable dldo4.
 233
 234 config AXP_ELDO1_VOLT
 235         int "axp pmic eldo1 voltage"
 236         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 237         default 0
 238         ---help---
 239         Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to
 240         disable eldo1.
 241
 242 config AXP_ELDO2_VOLT
 243         int "axp pmic eldo2 voltage"
 244         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 245         default 0
 246         ---help---
 247         Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to
 248         disable eldo2.
 249
 250 config AXP_ELDO3_VOLT
 251         int "axp pmic eldo3 voltage"
 252         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 253         default 3000 if MACH_SUN9I
 254         default 0
 255         ---help---
 256         Set the voltage (mV) to program the axp pmic eldo3 at, set to 0 to
 257         disable eldo3. On some A31(s) tablets it might be used to supply
 258         1.2V for the SSD2828 chip (converter of parallel LCD interface
 259         into MIPI DSI).
 260         On A80 boards it powers the PM pingroup and should be 3.0V.
 261
 262 config AXP_FLDO1_VOLT
 263         int "axp pmic fldo1 voltage"
 264         depends on AXP818_POWER
 265         default 0 if MACH_SUN8I_A83T
 266         ---help---
 267         Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to
 268         disable fldo1.
 269         On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is
 270         used.
 271
 272 config AXP_FLDO2_VOLT
 273         int "axp pmic fldo2 voltage"
 274         depends on AXP818_POWER
 275         default 900 if MACH_SUN8I_A83T
 276         ---help---
 277         Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to
 278         disable fldo2.
 279         On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V.
 280
 281 config AXP_FLDO3_VOLT
 282         int "axp pmic fldo3 voltage"
 283         depends on AXP818_POWER
 284         default 0
 285         ---help---
 286         Set the voltage (mV) to program the axp pmic fldo3 at, set to 0 to
 287         disable fldo3.
 288
 289 config AXP_SW_ON
 290         bool "axp pmic sw on"
 291         depends on AXP809_POWER || AXP818_POWER
 292         default n
 293         ---help---
 294         Enable to turn on axp pmic sw.
 295
 296 config SY8106A_VOUT1_VOLT
 297         int "SY8106A pmic VOUT1 voltage"
 298         depends on SY8106A_POWER
 299         default 1200
 300         ---help---
 301         Set the voltage (mV) to program the SY8106A pmic VOUT1. This
 302         is typically used to power the VDD-CPU and should be 1200mV.
 303         Values can range from 680mV till 1950mV.
 304
 305 endmenu