drivers/spi/Kconfig

   1 # SPDX-License-Identifier: GPL-2.0-only
   2 #
   3 # SPI driver configuration
   4 #
   5 menuconfig SPI
   6         bool "SPI support"
   7         depends on HAS_IOMEM
   8         help
   9           The "Serial Peripheral Interface" is a low level synchronous
  10           protocol.  Chips that support SPI can have data transfer rates
  11           up to several tens of Mbit/sec.  Chips are addressed with a
  12           controller and a chipselect.  Most SPI slaves don't support
  13           dynamic device discovery; some are even write-only or read-only.
  14
  15           SPI is widely used by microcontrollers to talk with sensors,
  16           eeprom and flash memory, codecs and various other controller
  17           chips, analog to digital (and d-to-a) converters, and more.
  18           MMC and SD cards can be accessed using SPI protocol; and for
  19           DataFlash cards used in MMC sockets, SPI must always be used.
  20
  21           SPI is one of a family of similar protocols using a four wire
  22           interface (select, clock, data in, data out) including Microwire
  23           (half duplex), SSP, SSI, and PSP.  This driver framework should
  24           work with most such devices and controllers.
  25
  26 if SPI
  27
  28 config SPI_DEBUG
  29         bool "Debug support for SPI drivers"
  30         depends on DEBUG_KERNEL
  31         help
  32           Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
  33           sysfs, and debugfs support in SPI controller and protocol drivers.
  34
  35 #
  36 # MASTER side ... talking to discrete SPI slave chips including microcontrollers
  37 #
  38
  39 config SPI_MASTER
  40 #       bool "SPI Master Support"
  41         bool
  42         default SPI
  43         help
  44           If your system has an master-capable SPI controller (which
  45           provides the clock and chipselect), you can enable that
  46           controller and the protocol drivers for the SPI slave chips
  47           that are connected.
  48
  49 if SPI_MASTER
  50
  51 config SPI_MEM
  52         bool "SPI memory extension"
  53         help
  54           Enable this option if you want to enable the SPI memory extension.
  55           This extension is meant to simplify interaction with SPI memories
  56           by providing a high-level interface to send memory-like commands.
  57
  58 comment "SPI Master Controller Drivers"
  59
  60 config SPI_ALTERA
  61         tristate "Altera SPI Controller platform driver"
  62         select SPI_ALTERA_CORE
  63         select REGMAP_MMIO
  64         help
  65           This is the driver for the Altera SPI Controller.
  66
  67 config SPI_ALTERA_CORE
  68         tristate "Altera SPI Controller core code" if COMPILE_TEST
  69         select REGMAP
  70         help
  71           "The core code for the Altera SPI Controller"
  72
  73 config SPI_ALTERA_DFL
  74         tristate "DFL bus driver for Altera SPI Controller"
  75         depends on FPGA_DFL
  76         select SPI_ALTERA_CORE
  77         help
  78           This is a Device Feature List (DFL) bus driver for the
  79           Altera SPI master controller.  The SPI master is connected
  80           to a SPI slave to Avalon bridge in a Intel MAX BMC.
  81
  82 config SPI_AMLOGIC_SPIFC_A1
  83         tristate "Amlogic A1 SPIFC controller"
  84         depends on ARCH_MESON || COMPILE_TEST
  85         help
  86           This enables master mode support for the SPIFC (SPI flash
  87           controller) available in Amlogic A1 (A113L SoC).
  88
  89 config SPI_AR934X
  90         tristate "Qualcomm Atheros AR934X/QCA95XX SPI controller driver"
  91         depends on ATH79 || COMPILE_TEST
  92         help
  93           This enables support for the SPI controller present on the
  94           Qualcomm Atheros AR934X/QCA95XX SoCs.
  95
  96 config SPI_ATH79
  97         tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
  98         depends on ATH79 || COMPILE_TEST
  99         select SPI_BITBANG
 100         help
 101           This enables support for the SPI controller present on the
 102           Atheros AR71XX/AR724X/AR913X SoCs.
 103
 104 config SPI_ARMADA_3700
 105         tristate "Marvell Armada 3700 SPI Controller"
 106         depends on (ARCH_MVEBU && OF) || COMPILE_TEST
 107         help
 108           This enables support for the SPI controller present on the
 109           Marvell Armada 3700 SoCs.
 110
 111 config SPI_ASPEED_SMC
 112         tristate "Aspeed flash controllers in SPI mode"
 113         depends on ARCH_ASPEED || COMPILE_TEST
 114         depends on OF
 115         help
 116           This enables support for the Firmware Memory controller (FMC)
 117           in the Aspeed AST2600, AST2500 and AST2400 SoCs when attached
 118           to SPI NOR chips, and support for the SPI flash memory
 119           controller (SPI) for the host firmware. The implementation
 120           only supports SPI NOR.
 121
 122 config SPI_ATMEL
 123         tristate "Atmel SPI Controller"
 124         depends on ARCH_AT91 || COMPILE_TEST
 125         depends on OF
 126         help
 127           This selects a driver for the Atmel SPI Controller, present on
 128           many AT91 ARM chips.
 129
 130 config SPI_AT91_USART
 131         tristate "Atmel USART Controller SPI driver"
 132         depends on (ARCH_AT91 || COMPILE_TEST)
 133         depends on MFD_AT91_USART
 134         help
 135           This selects a driver for the AT91 USART Controller as SPI Master,
 136           present on AT91 and SAMA5 SoC series.
 137
 138 config SPI_ATMEL_QUADSPI
 139         tristate "Atmel Quad SPI Controller"
 140         depends on ARCH_AT91 || COMPILE_TEST
 141         depends on OF && HAS_IOMEM
 142         help
 143           This enables support for the Quad SPI controller in master mode.
 144           This driver does not support generic SPI. The implementation only
 145           supports spi-mem interface.
 146
 147 config SPI_AU1550
 148         tristate "Au1550/Au1200/Au1300 SPI Controller"
 149         depends on MIPS_ALCHEMY
 150         select SPI_BITBANG
 151         help
 152           If you say yes to this option, support will be included for the
 153           PSC SPI controller found on Au1550, Au1200 and Au1300 series.
 154
 155 config SPI_AXI_SPI_ENGINE
 156         tristate "Analog Devices AXI SPI Engine controller"
 157         depends on HAS_IOMEM
 158         help
 159           This enables support for the Analog Devices AXI SPI Engine SPI controller.
 160           It is part of the SPI Engine framework that is used in some Analog Devices
 161           reference designs for FPGAs.
 162
 163 config SPI_BCM2835
 164         tristate "BCM2835 SPI controller"
 165         depends on GPIOLIB
 166         depends on ARCH_BCM2835 || ARCH_BRCMSTB || COMPILE_TEST
 167         help
 168           This selects a driver for the Broadcom BCM2835 SPI master.
 169
 170           The BCM2835 contains two types of SPI master controller; the
 171           "universal SPI master", and the regular SPI controller. This driver
 172           is for the regular SPI controller. Slave mode operation is not also
 173           not supported.
 174
 175 config SPI_BCM2835AUX
 176         tristate "BCM2835 SPI auxiliary controller"
 177         depends on ((ARCH_BCM2835 || ARCH_BRCMSTB) && GPIOLIB) || COMPILE_TEST
 178         help
 179           This selects a driver for the Broadcom BCM2835 SPI aux master.
 180
 181           The BCM2835 contains two types of SPI master controller; the
 182           "universal SPI master", and the regular SPI controller.
 183           This driver is for the universal/auxiliary SPI controller.
 184
 185 config SPI_BCM63XX
 186         tristate "Broadcom BCM63xx SPI controller"
 187         depends on BCM63XX || BMIPS_GENERIC || COMPILE_TEST
 188         help
 189           Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
 190
 191 config SPI_BCM63XX_HSSPI
 192         tristate "Broadcom BCM63XX HS SPI controller driver"
 193         depends on BCM63XX || BMIPS_GENERIC || ARCH_BCMBCA || COMPILE_TEST
 194         help
 195           This enables support for the High Speed SPI controller present on
 196           newer Broadcom BCM63XX SoCs.
 197
 198 config SPI_BCM_QSPI
 199         tristate "Broadcom BSPI and MSPI controller support"
 200         depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || \
 201                         BMIPS_GENERIC || COMPILE_TEST
 202         default ARCH_BCM_IPROC
 203         help
 204           Enables support for the Broadcom SPI flash and MSPI controller.
 205           Select this option for any one of BRCMSTB, iProc NSP and NS2 SoCs
 206           based platforms. This driver works for both SPI master for SPI NOR
 207           flash device as well as MSPI device.
 208
 209 config SPI_BCMBCA_HSSPI
 210         tristate "Broadcom BCMBCA HS SPI controller driver"
 211         depends on ARCH_BCMBCA || COMPILE_TEST
 212         help
 213           This enables support for the High Speed SPI controller present on
 214           newer Broadcom BCMBCA SoCs. These SoCs include an updated SPI controller
 215           that adds the capability to allow the driver to control chip select
 216           explicitly.
 217
 218 config SPI_BITBANG
 219         tristate "Utilities for Bitbanging SPI masters"
 220         help
 221           With a few GPIO pins, your system can bitbang the SPI protocol.
 222           Select this to get SPI support through I/O pins (GPIO, parallel
 223           port, etc).  Or, some systems' SPI master controller drivers use
 224           this code to manage the per-word or per-transfer accesses to the
 225           hardware shift registers.
 226
 227           This is library code, and is automatically selected by drivers that
 228           need it.  You only need to select this explicitly to support driver
 229           modules that aren't part of this kernel tree.
 230
 231 config SPI_BUTTERFLY
 232         tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
 233         depends on PARPORT
 234         select SPI_BITBANG
 235         help
 236           This uses a custom parallel port cable to connect to an AVR
 237           Butterfly <http://www.atmel.com/products/avr/butterfly>, an
 238           inexpensive battery powered microcontroller evaluation board.
 239           This same cable can be used to flash new firmware.
 240
 241 config SPI_CADENCE
 242         tristate "Cadence SPI controller"
 243         help
 244           This selects the Cadence SPI controller master driver
 245           used by Xilinx Zynq and ZynqMP.
 246
 247 config SPI_CADENCE_QUADSPI
 248         tristate "Cadence Quad SPI controller"
 249         depends on OF && (ARM || ARM64 || X86 || RISCV || COMPILE_TEST)
 250         help
 251           Enable support for the Cadence Quad SPI Flash controller.
 252
 253           Cadence QSPI is a specialized controller for connecting an SPI
 254           Flash over 1/2/4-bit wide bus. Enable this option if you have a
 255           device with a Cadence QSPI controller and want to access the
 256           Flash as an MTD device.
 257
 258 config SPI_CADENCE_XSPI
 259         tristate "Cadence XSPI controller"
 260         depends on OF && HAS_IOMEM
 261         depends on SPI_MEM
 262         help
 263           Enable support for the Cadence XSPI Flash controller.
 264
 265           Cadence XSPI is a specialized controller for connecting an SPI
 266           Flash over up to 8-bit wide bus. Enable this option if you have a
 267           device with a Cadence XSPI controller and want to access the
 268           Flash as an MTD device.
 269
 270 config SPI_CLPS711X
 271         tristate "CLPS711X host SPI controller"
 272         depends on ARCH_CLPS711X || COMPILE_TEST
 273         help
 274           This enables dedicated general purpose SPI/Microwire1-compatible
 275           master mode interface (SSI1) for CLPS711X-based CPUs.
 276
 277 config SPI_COLDFIRE_QSPI
 278         tristate "Freescale Coldfire QSPI controller"
 279         depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
 280         help
 281           This enables support for the Coldfire QSPI controller in master
 282           mode.
 283
 284 config SPI_CS42L43
 285         tristate "Cirrus Logic CS42L43 SPI controller"
 286         depends on MFD_CS42L43 && PINCTRL_CS42L43
 287         help
 288           This enables support for the SPI controller inside the Cirrus Logic
 289           CS42L43 audio codec.
 290
 291 config SPI_DAVINCI
 292         tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
 293         depends on ARCH_DAVINCI || ARCH_KEYSTONE || COMPILE_TEST
 294         select SPI_BITBANG
 295         help
 296           SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
 297
 298 config SPI_DESIGNWARE
 299         tristate "DesignWare SPI controller core support"
 300         imply SPI_MEM
 301         help
 302           general driver for SPI controller core from DesignWare
 303
 304 if SPI_DESIGNWARE
 305
 306 config SPI_DW_DMA
 307         bool "DMA support for DW SPI controller"
 308
 309 config SPI_DW_PCI
 310         tristate "PCI interface driver for DW SPI core"
 311         depends on PCI
 312
 313 config SPI_DW_MMIO
 314         tristate "Memory-mapped io interface driver for DW SPI core"
 315         depends on HAS_IOMEM
 316
 317 config SPI_DW_BT1
 318         tristate "Baikal-T1 SPI driver for DW SPI core"
 319         depends on MIPS_BAIKAL_T1 || COMPILE_TEST
 320         select MULTIPLEXER
 321         help
 322           Baikal-T1 SoC is equipped with three DW APB SSI-based MMIO SPI
 323           controllers. Two of them are pretty much normal: with IRQ, DMA,
 324           FIFOs of 64 words depth, 4x CSs, but the third one as being a
 325           part of the Baikal-T1 System Boot Controller has got a very
 326           limited resources: no IRQ, no DMA, only a single native
 327           chip-select and Tx/Rx FIFO with just 8 words depth available.
 328           The later one is normally connected to an external SPI-nor flash
 329           of 128Mb (in general can be of bigger size).
 330
 331 config SPI_DW_BT1_DIRMAP
 332         bool "Directly mapped Baikal-T1 Boot SPI flash support"
 333         depends on SPI_DW_BT1
 334         help
 335           Directly mapped SPI flash memory is an interface specific to the
 336           Baikal-T1 System Boot Controller. It is a 16MB MMIO region, which
 337           can be used to access a peripheral memory device just by
 338           reading/writing data from/to it. Note that the system APB bus
 339           will stall during each IO from/to the dirmap region until the
 340           operation is finished. So try not to use it concurrently with
 341           time-critical tasks (like the SPI memory operations implemented
 342           in this driver).
 343
 344 endif
 345
 346 config SPI_DLN2
 347        tristate "Diolan DLN-2 USB SPI adapter"
 348        depends on MFD_DLN2
 349        help
 350          If you say yes to this option, support will be included for Diolan
 351          DLN2, a USB to SPI interface.
 352
 353          This driver can also be built as a module.  If so, the module
 354          will be called spi-dln2.
 355
 356 config SPI_EP93XX
 357         tristate "Cirrus Logic EP93xx SPI controller"
 358         depends on ARCH_EP93XX || COMPILE_TEST
 359         help
 360           This enables using the Cirrus EP93xx SPI controller in master
 361           mode.
 362
 363 config SPI_FALCON
 364         bool "Falcon SPI controller support"
 365         depends on SOC_FALCON
 366         help
 367           The external bus unit (EBU) found on the FALC-ON SoC has SPI
 368           emulation that is designed for serial flash access. This driver
 369           has only been tested with m25p80 type chips. The hardware has no
 370           support for other types of SPI peripherals.
 371
 372 config SPI_FSI
 373         tristate "FSI SPI driver"
 374         depends on FSI
 375         help
 376           This enables support for the driver for FSI bus attached SPI
 377           controllers.
 378
 379 config SPI_FSL_LPSPI
 380         tristate "Freescale i.MX LPSPI controller"
 381         depends on ARCH_MXC || COMPILE_TEST
 382         help
 383           This enables Freescale i.MX LPSPI controllers in master mode.
 384
 385 config SPI_FSL_QUADSPI
 386         tristate "Freescale QSPI controller"
 387         depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
 388         depends on HAS_IOMEM
 389         help
 390           This enables support for the Quad SPI controller in master mode.
 391           Up to four flash chips can be connected on two buses with two
 392           chipselects each.
 393           This controller does not support generic SPI messages. It only
 394           supports the high-level SPI memory interface.
 395
 396 config SPI_GXP
 397         tristate "GXP SPI driver"
 398         depends on ARCH_HPE || COMPILE_TEST
 399         help
 400           This enables support for the driver for GXP bus attached SPI
 401           controllers.
 402
 403 config SPI_HISI_KUNPENG
 404         tristate "HiSilicon SPI Controller for Kunpeng SoCs"
 405         depends on (ARM64 && ACPI) || COMPILE_TEST
 406         help
 407           This enables support for HiSilicon SPI controller found on
 408           Kunpeng SoCs.
 409
 410           This driver can also be built as a module. If so, the module
 411           will be called hisi-kunpeng-spi.
 412
 413 config SPI_HISI_SFC_V3XX
 414         tristate "HiSilicon SPI NOR Flash Controller for Hi16XX chipsets"
 415         depends on (ARM64 && ACPI) || COMPILE_TEST
 416         depends on HAS_IOMEM
 417         help
 418           This enables support for HiSilicon v3xx SPI NOR flash controller
 419           found in hi16xx chipsets.
 420
 421 config SPI_NXP_FLEXSPI
 422         tristate "NXP Flex SPI controller"
 423         depends on ARCH_LAYERSCAPE || ARCH_MXC || COMPILE_TEST
 424         depends on HAS_IOMEM
 425         help
 426           This enables support for the Flex SPI controller in master mode.
 427           Up to four slave devices can be connected on two buses with two
 428           chipselects each.
 429           This controller does not support generic SPI messages and only
 430           supports the high-level SPI memory interface.
 431
 432 config SPI_GPIO
 433         tristate "GPIO-based bitbanging SPI Master"
 434         depends on GPIOLIB || COMPILE_TEST
 435         select SPI_BITBANG
 436         help
 437           This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
 438           interface to manage MOSI, MISO, SCK, and chipselect signals.  SPI
 439           slaves connected to a bus using this driver are configured as usual,
 440           except that the spi_board_info.controller_data holds the GPIO number
 441           for the chipselect used by this controller driver.
 442
 443           Note that this driver often won't achieve even 1 Mbit/sec speeds,
 444           making it unusually slow for SPI.  If your platform can inline
 445           GPIO operations, you should be able to leverage that for better
 446           speed with a custom version of this driver; see the source code.
 447
 448 config SPI_IMG_SPFI
 449         tristate "IMG SPFI controller"
 450         depends on MIPS || COMPILE_TEST
 451         help
 452           This enables support for the SPFI master controller found on
 453           IMG SoCs.
 454
 455 config SPI_IMX
 456         tristate "Freescale i.MX SPI controllers"
 457         depends on ARCH_MXC || COMPILE_TEST
 458         help
 459           This enables support for the Freescale i.MX SPI controllers.
 460
 461 config SPI_INGENIC
 462         tristate "Ingenic SoCs SPI controller"
 463         depends on MACH_INGENIC || COMPILE_TEST
 464         help
 465           This enables support for the Ingenic SoCs SPI controller.
 466
 467           To compile this driver as a module, choose M here: the module
 468           will be called spi-ingenic.
 469
 470 config SPI_INTEL
 471         tristate
 472
 473 config SPI_INTEL_PCI
 474         tristate "Intel PCH/PCU SPI flash PCI driver"
 475         depends on PCI
 476         depends on X86 || COMPILE_TEST
 477         depends on SPI_MEM
 478         select SPI_INTEL
 479         help
 480           This enables PCI support for the Intel PCH/PCU SPI controller in
 481           master mode. This controller is used to hold BIOS and other
 482           persistent settings. Controllers present in modern Intel hardware
 483           only work in hardware sequencing mode, this means that the
 484           controller exposes a subset of operations that makes it safer to
 485           use. Using this driver it is possible to upgrade BIOS directly
 486           from Linux.
 487
 488           To compile this driver as a module, choose M here: the module
 489           will be called spi-intel-pci.
 490
 491 config SPI_INTEL_PLATFORM
 492         tristate "Intel PCH/PCU SPI flash platform driver (DANGEROUS)"
 493         depends on X86 || COMPILE_TEST
 494         depends on SPI_MEM
 495         select SPI_INTEL
 496         help
 497           This enables platform support for the Intel PCH/PCU SPI
 498           controller in master mode that is used to hold BIOS and other
 499           persistent settings. Most of these controllers work in
 500           software sequencing mode, which means that the controller
 501           exposes the low level SPI-NOR opcodes to the software. Using
 502           this driver it is possible to upgrade BIOS directly from Linux.
 503
 504           Say N here unless you know what you are doing. Overwriting the
 505           SPI flash may render the system unbootable.
 506
 507           To compile this driver as a module, choose M here: the module
 508           will be called spi-intel-platform.
 509
 510 config SPI_JCORE
 511         tristate "J-Core SPI Master"
 512         depends on OF && (SUPERH || COMPILE_TEST)
 513         help
 514           This enables support for the SPI master controller in the J-Core
 515           synthesizable, open source SoC.
 516
 517 config SPI_LM70_LLP
 518         tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
 519         depends on PARPORT
 520         select SPI_BITBANG
 521         help
 522           This driver supports the NS LM70 LLP Evaluation Board,
 523           which interfaces to an LM70 temperature sensor using
 524           a parallel port.
 525
 526 config SPI_LOONGSON_CORE
 527         tristate
 528         depends on LOONGARCH || COMPILE_TEST
 529
 530 config SPI_LOONGSON_PCI
 531         tristate "Loongson SPI Controller PCI Driver Support"
 532         select SPI_LOONGSON_CORE
 533         depends on PCI && (LOONGARCH || COMPILE_TEST)
 534         help
 535           This bus driver supports the Loongson SPI hardware controller in
 536           the Loongson platforms and supports to use PCI framework to
 537           register SPI device resources.
 538           Say Y or M here if you want to use the SPI controller on
 539           Loongson platform.
 540
 541 config SPI_LOONGSON_PLATFORM
 542         tristate "Loongson SPI Controller Platform Driver Support"
 543         select SPI_LOONGSON_CORE
 544         depends on OF && (LOONGARCH || COMPILE_TEST)
 545         help
 546           This bus driver supports the Loongson SPI hardware controller in
 547           the Loongson platforms and supports to use DTS framework to
 548           register SPI device resources.
 549           Say Y or M here if you want to use the SPI controller on
 550           Loongson platform.
 551
 552 config SPI_LP8841_RTC
 553         tristate "ICP DAS LP-8841 SPI Controller for RTC"
 554         depends on MACH_PXA27X_DT || COMPILE_TEST
 555         help
 556           This driver provides an SPI master device to drive Maxim
 557           DS-1302 real time clock.
 558
 559           Say N here unless you plan to run the kernel on an ICP DAS
 560           LP-8x4x industrial computer.
 561
 562 config SPI_MPC52xx
 563         tristate "Freescale MPC52xx SPI (non-PSC) controller support"
 564         depends on PPC_MPC52xx
 565         help
 566           This drivers supports the MPC52xx SPI controller in master SPI
 567           mode.
 568
 569 config SPI_MPC52xx_PSC
 570         tristate "Freescale MPC52xx PSC SPI controller"
 571         depends on PPC_MPC52xx
 572         help
 573           This enables using the Freescale MPC52xx Programmable Serial
 574           Controller in master SPI mode.
 575
 576 config SPI_MPC512x_PSC
 577         tristate "Freescale MPC512x PSC SPI controller"
 578         depends on PPC_MPC512x
 579         help
 580           This enables using the Freescale MPC5121 Programmable Serial
 581           Controller in SPI master mode.
 582
 583 config SPI_FSL_LIB
 584         tristate
 585         depends on OF
 586
 587 config SPI_FSL_CPM
 588         tristate
 589         depends on FSL_SOC
 590
 591 config SPI_FSL_SPI
 592         tristate "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
 593         depends on OF
 594         select SPI_FSL_LIB
 595         select SPI_FSL_CPM if FSL_SOC
 596         help
 597           This enables using the Freescale SPI controllers in master mode.
 598           MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
 599           MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
 600           This also enables using the Aeroflex Gaisler GRLIB SPI controller in
 601           master mode.
 602
 603 config SPI_FSL_DSPI
 604         tristate "Freescale DSPI controller"
 605         select REGMAP_MMIO
 606         depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || M5441x || COMPILE_TEST
 607         help
 608           This enables support for the Freescale DSPI controller in master
 609           mode. VF610, LS1021A and ColdFire platforms uses the controller.
 610
 611 config SPI_FSL_ESPI
 612         tristate "Freescale eSPI controller"
 613         depends on FSL_SOC
 614         help
 615           This enables using the Freescale eSPI controllers in master mode.
 616           From MPC8536, 85xx platform uses the controller, and all P10xx,
 617           P20xx, P30xx,P40xx, P50xx uses this controller.
 618
 619 config SPI_LJCA
 620         tristate "Intel La Jolla Cove Adapter SPI support"
 621         depends on USB_LJCA
 622         default USB_LJCA
 623         help
 624           Select this option to enable SPI driver for the Intel
 625           La Jolla Cove Adapter (LJCA) board.
 626
 627           This driver can also be built as a module. If so, the module
 628           will be called spi-ljca.
 629
 630 config SPI_MESON_SPICC
 631         tristate "Amlogic Meson SPICC controller"
 632         depends on COMMON_CLK
 633         depends on ARCH_MESON || COMPILE_TEST
 634         help
 635           This enables master mode support for the SPICC (SPI communication
 636           controller) available in Amlogic Meson SoCs.
 637
 638 config SPI_MESON_SPIFC
 639         tristate "Amlogic Meson SPIFC controller"
 640         depends on ARCH_MESON || COMPILE_TEST
 641         select REGMAP_MMIO
 642         help
 643           This enables master mode support for the SPIFC (SPI flash
 644           controller) available in Amlogic Meson SoCs.
 645
 646 config SPI_MICROCHIP_CORE
 647         tristate "Microchip FPGA SPI controllers"
 648         depends on SPI_MASTER
 649         help
 650           This enables the SPI driver for Microchip FPGA SPI controllers.
 651           Say Y or M here if you want to use the "hard" controllers on
 652           PolarFire SoC.
 653           If built as a module, it will be called spi-microchip-core.
 654
 655 config SPI_MICROCHIP_CORE_QSPI
 656         tristate "Microchip FPGA QSPI controllers"
 657         depends on SPI_MASTER
 658         help
 659           This enables the QSPI driver for Microchip FPGA QSPI controllers.
 660           Say Y or M here if you want to use the QSPI controllers on
 661           PolarFire SoC.
 662           If built as a module, it will be called spi-microchip-core-qspi.
 663
 664 config SPI_MT65XX
 665         tristate "MediaTek SPI controller"
 666         depends on ARCH_MEDIATEK || COMPILE_TEST
 667         help
 668           This selects the MediaTek(R) SPI bus driver.
 669           If you want to use MediaTek(R) SPI interface,
 670           say Y or M here.If you are not sure, say N.
 671           SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
 672
 673 config SPI_MT7621
 674         tristate "MediaTek MT7621 SPI Controller"
 675         depends on RALINK || COMPILE_TEST
 676         help
 677           This selects a driver for the MediaTek MT7621 SPI Controller.
 678
 679 config SPI_MTK_NOR
 680         tristate "MediaTek SPI NOR controller"
 681         depends on ARCH_MEDIATEK || COMPILE_TEST
 682         help
 683           This enables support for SPI NOR controller found on MediaTek
 684           ARM SoCs. This is a controller specifically for SPI NOR flash.
 685           It can perform generic SPI transfers up to 6 bytes via generic
 686           SPI interface as well as several SPI NOR specific instructions
 687           via SPI MEM interface.
 688
 689 config SPI_MTK_SNFI
 690         tristate "MediaTek SPI NAND Flash Interface"
 691         depends on ARCH_MEDIATEK || COMPILE_TEST
 692         depends on MTD_NAND_ECC_MEDIATEK
 693         help
 694           This enables support for SPI-NAND mode on the MediaTek NAND
 695           Flash Interface found on MediaTek ARM SoCs. This controller
 696           is implemented as a SPI-MEM controller with pipelined ECC
 697           capcability.
 698
 699 config SPI_WPCM_FIU
 700         tristate "Nuvoton WPCM450 Flash Interface Unit"
 701         depends on ARCH_NPCM || COMPILE_TEST
 702         select REGMAP
 703         help
 704           This enables support got the Flash Interface Unit SPI controller
 705           present in the Nuvoton WPCM450 SoC.
 706
 707           This driver does not support generic SPI. The implementation only
 708           supports the spi-mem interface.
 709
 710 config SPI_NPCM_FIU
 711         tristate "Nuvoton NPCM FLASH Interface Unit"
 712         depends on ARCH_NPCM || COMPILE_TEST
 713         depends on OF && HAS_IOMEM
 714         help
 715           This enables support for the Flash Interface Unit SPI controller
 716           in master mode.
 717           This driver does not support generic SPI. The implementation only
 718           supports spi-mem interface.
 719
 720 config SPI_NPCM_PSPI
 721         tristate "Nuvoton NPCM PSPI Controller"
 722         depends on ARCH_NPCM || COMPILE_TEST
 723         help
 724           This driver provides support for Nuvoton NPCM BMC
 725           Peripheral SPI controller in master mode.
 726
 727 config SPI_LANTIQ_SSC
 728         tristate "Lantiq SSC SPI controller"
 729         depends on LANTIQ || X86 || COMPILE_TEST
 730         help
 731           This driver supports the Lantiq SSC SPI controller in master
 732           mode. This controller is found on Intel (former Lantiq) SoCs like
 733           the Danube, Falcon, xRX200, xRX300, Lightning Mountain.
 734
 735 config SPI_OC_TINY
 736         tristate "OpenCores tiny SPI"
 737         depends on GPIOLIB || COMPILE_TEST
 738         select SPI_BITBANG
 739         help
 740           This is the driver for OpenCores tiny SPI master controller.
 741
 742 config SPI_OCTEON
 743         tristate "Cavium OCTEON SPI controller"
 744         depends on CAVIUM_OCTEON_SOC
 745         help
 746           SPI host driver for the hardware found on some Cavium OCTEON
 747           SOCs.
 748
 749 config SPI_OMAP_UWIRE
 750         tristate "OMAP1 MicroWire"
 751         depends on ARCH_OMAP1 || (ARM && COMPILE_TEST)
 752         select SPI_BITBANG
 753         help
 754           This hooks up to the MicroWire controller on OMAP1 chips.
 755
 756 config SPI_OMAP24XX
 757         tristate "McSPI driver for OMAP"
 758         depends on ARCH_OMAP2PLUS || ARCH_K3 || COMPILE_TEST
 759         select SG_SPLIT
 760         help
 761           SPI master controller for OMAP24XX and later Multichannel SPI
 762           (McSPI) modules.
 763
 764 config SPI_TI_QSPI
 765         tristate "DRA7xxx QSPI controller support"
 766         depends on ARCH_OMAP2PLUS || COMPILE_TEST
 767         help
 768           QSPI master controller for DRA7xxx used for flash devices.
 769           This device supports single, dual and quad read support, while
 770           it only supports single write mode.
 771
 772 config SPI_ORION
 773         tristate "Orion SPI master"
 774         depends on PLAT_ORION || ARCH_MVEBU || COMPILE_TEST
 775         help
 776           This enables using the SPI master controller on the Orion
 777           and MVEBU chips.
 778
 779 config SPI_PCI1XXXX
 780         tristate "PCI1XXXX SPI Bus support"
 781         depends on PCI
 782         help
 783           Say "yes" to Enable the SPI Bus support for the PCI1xxxx card
 784           This is a PCI to SPI Bus driver
 785           This driver can be built as module. If so, the module will be
 786           called as spi-pci1xxxx.
 787
 788 config SPI_PIC32
 789         tristate "Microchip PIC32 series SPI"
 790         depends on MACH_PIC32 || COMPILE_TEST
 791         help
 792           SPI driver for Microchip PIC32 SPI master controller.
 793
 794 config SPI_PIC32_SQI
 795         tristate "Microchip PIC32 Quad SPI driver"
 796         depends on MACH_PIC32 || COMPILE_TEST
 797         help
 798           SPI driver for PIC32 Quad SPI controller.
 799
 800 config SPI_PL022
 801         tristate "ARM AMBA PL022 SSP controller"
 802         depends on ARM_AMBA
 803         default y if ARCH_REALVIEW
 804         default y if INTEGRATOR_IMPD1
 805         default y if ARCH_VERSATILE
 806         help
 807           This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
 808           controller. If you have an embedded system with an AMBA(R)
 809           bus and a PL022 controller, say Y or M here.
 810
 811 config SPI_PPC4xx
 812         tristate "PPC4xx SPI Controller"
 813         depends on PPC32 && 4xx
 814         select SPI_BITBANG
 815         help
 816           This selects a driver for the PPC4xx SPI Controller.
 817
 818 config SPI_PXA2XX
 819         tristate "PXA2xx SSP SPI master"
 820         depends on ARCH_PXA || ARCH_MMP || PCI || ACPI || COMPILE_TEST
 821         select PXA_SSP if ARCH_PXA || ARCH_MMP
 822         help
 823           This enables using a PXA2xx or Sodaville SSP port as a SPI master
 824           controller. The driver can be configured to use any SSP port and
 825           additional documentation can be found a Documentation/spi/pxa2xx.rst.
 826
 827 config SPI_PXA2XX_PCI
 828         def_tristate SPI_PXA2XX && PCI && COMMON_CLK
 829
 830 config SPI_ROCKCHIP
 831         tristate "Rockchip SPI controller driver"
 832         depends on ARCH_ROCKCHIP || COMPILE_TEST
 833         help
 834           This selects a driver for Rockchip SPI controller.
 835
 836           If you say yes to this option, support will be included for
 837           RK3066, RK3188 and RK3288 families of SPI controller.
 838           Rockchip SPI controller support DMA transport and PIO mode.
 839           The main usecase of this controller is to use spi flash as boot
 840           device.
 841
 842 config SPI_ROCKCHIP_SFC
 843         tristate "Rockchip Serial Flash Controller (SFC)"
 844         depends on ARCH_ROCKCHIP || COMPILE_TEST
 845         depends on HAS_IOMEM && HAS_DMA
 846         help
 847           This enables support for Rockchip serial flash controller. This
 848           is a specialized controller used to access SPI flash on some
 849           Rockchip SOCs.
 850
 851           ROCKCHIP SFC supports DMA and PIO modes. When DMA is not available,
 852           the driver automatically falls back to PIO mode.
 853
 854 config SPI_RB4XX
 855         tristate "Mikrotik RB4XX SPI master"
 856         depends on SPI_MASTER && ATH79
 857         help
 858           SPI controller driver for the Mikrotik RB4xx series boards.
 859
 860 config SPI_RPCIF
 861         tristate "Renesas RPC-IF SPI driver"
 862         depends on RENESAS_RPCIF
 863         help
 864           SPI driver for Renesas R-Car Gen3 or RZ/G2 RPC-IF.
 865
 866 config SPI_RSPI
 867         tristate "Renesas RSPI/QSPI controller"
 868         depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
 869         help
 870           SPI driver for Renesas RSPI and QSPI blocks.
 871
 872 config SPI_RZV2M_CSI
 873         tristate "Renesas RZ/V2M CSI controller"
 874         depends on ARCH_RENESAS || COMPILE_TEST
 875         help
 876           SPI driver for Renesas RZ/V2M Clocked Serial Interface (CSI).
 877           CSI supports both SPI host and SPI target roles.
 878
 879 config SPI_QCOM_QSPI
 880         tristate "QTI QSPI controller"
 881         depends on ARCH_QCOM || COMPILE_TEST
 882         help
 883           QSPI(Quad SPI) driver for Qualcomm QSPI controller.
 884
 885 config SPI_QUP
 886         tristate "Qualcomm SPI controller with QUP interface"
 887         depends on ARCH_QCOM || COMPILE_TEST
 888         help
 889           Qualcomm Universal Peripheral (QUP) core is an AHB slave that
 890           provides a common data path (an output FIFO and an input FIFO)
 891           for serial peripheral interface (SPI) mini-core. SPI in master
 892           mode supports up to 50MHz, up to four chip selects, programmable
 893           data path from 4 bits to 32 bits and numerous protocol variants.
 894
 895           This driver can also be built as a module.  If so, the module
 896           will be called spi_qup.
 897
 898 config SPI_QCOM_GENI
 899         tristate "Qualcomm GENI based SPI controller"
 900         depends on QCOM_GENI_SE
 901         help
 902           This driver supports GENI serial engine based SPI controller in
 903           master mode on the Qualcomm Technologies Inc.'s SoCs. If you say
 904           yes to this option, support will be included for the built-in SPI
 905           interface on the Qualcomm Technologies Inc.'s SoCs.
 906
 907           This driver can also be built as a module.  If so, the module
 908           will be called spi-geni-qcom.
 909
 910 config SPI_S3C64XX
 911         tristate "Samsung S3C64XX/Exynos SoC series type SPI"
 912         depends on (PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST)
 913         help
 914           SPI driver for Samsung S3C64XX, S5Pv210 and Exynos SoCs.
 915           Choose Y/M here only if you build for such Samsung SoC.
 916
 917 config SPI_SC18IS602
 918         tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
 919         depends on I2C
 920         help
 921           SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
 922
 923 config SPI_SH_MSIOF
 924         tristate "SuperH MSIOF SPI controller"
 925         depends on HAVE_CLK
 926         depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST
 927         help
 928           SPI driver for SuperH and SH Mobile MSIOF blocks.
 929
 930 config SPI_SH
 931         tristate "SuperH SPI controller"
 932         depends on SUPERH || COMPILE_TEST
 933         help
 934           SPI driver for SuperH SPI blocks.
 935
 936 config SPI_SH_SCI
 937         tristate "SuperH SCI SPI controller"
 938         depends on SUPERH
 939         select SPI_BITBANG
 940         help
 941           SPI driver for SuperH SCI blocks.
 942
 943 config SPI_SH_HSPI
 944         tristate "SuperH HSPI controller"
 945         depends on ARCH_RENESAS || COMPILE_TEST
 946         help
 947           SPI driver for SuperH HSPI blocks.
 948
 949 config SPI_SIFIVE
 950         tristate "SiFive SPI controller"
 951         depends on HAS_IOMEM
 952         help
 953           This exposes the SPI controller IP from SiFive.
 954
 955 config SPI_SLAVE_MT27XX
 956         tristate "MediaTek SPI slave device"
 957         depends on ARCH_MEDIATEK || COMPILE_TEST
 958         depends on SPI_SLAVE
 959         help
 960           This selects the MediaTek(R) SPI slave device driver.
 961           If you want to use MediaTek(R) SPI slave interface,
 962           say Y or M here.If you are not sure, say N.
 963           SPI slave drivers for Mediatek MT27XX series ARM SoCs.
 964
 965 config SPI_SN_F_OSPI
 966         tristate "Socionext F_OSPI SPI flash controller"
 967         depends on OF && HAS_IOMEM
 968         depends on SPI_MEM
 969         help
 970           This enables support for the Socionext F_OSPI controller
 971           for connecting an SPI Flash memory over up to 8-bit wide bus.
 972           It supports indirect access mode only.
 973
 974 config SPI_SPRD
 975         tristate "Spreadtrum SPI controller"
 976         depends on ARCH_SPRD || COMPILE_TEST
 977         help
 978           SPI driver for Spreadtrum SoCs.
 979
 980 config SPI_SPRD_ADI
 981         tristate "Spreadtrum ADI controller"
 982         depends on ARCH_SPRD || COMPILE_TEST
 983         depends on HWSPINLOCK || (COMPILE_TEST && !HWSPINLOCK)
 984         help
 985           ADI driver based on SPI for Spreadtrum SoCs.
 986
 987 config SPI_STM32
 988         tristate "STMicroelectronics STM32 SPI controller"
 989         depends on ARCH_STM32 || COMPILE_TEST
 990         select SPI_SLAVE
 991         help
 992           SPI driver for STMicroelectronics STM32 SoCs.
 993
 994           STM32 SPI controller supports DMA and PIO modes. When DMA
 995           is not available, the driver automatically falls back to
 996           PIO mode.
 997
 998 config SPI_STM32_QSPI
 999         tristate "STMicroelectronics STM32 QUAD SPI controller"
1000         depends on ARCH_STM32 || COMPILE_TEST
1001         depends on OF
1002         depends on SPI_MEM
1003         help
1004           This enables support for the Quad SPI controller in master mode.
1005           This driver does not support generic SPI. The implementation only
1006           supports spi-mem interface.
1007
1008 config SPI_ST_SSC4
1009         tristate "STMicroelectronics SPI SSC-based driver"
1010         depends on ARCH_STI || COMPILE_TEST
1011         help
1012           STMicroelectronics SoCs support for SPI. If you say yes to
1013           this option, support will be included for the SSC driven SPI.
1014
1015 config SPI_SUN4I
1016         tristate "Allwinner A10 SoCs SPI controller"
1017         depends on ARCH_SUNXI || COMPILE_TEST
1018         help
1019           SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
1020
1021 config SPI_SUN6I
1022         tristate "Allwinner A31 SPI controller"
1023         depends on ARCH_SUNXI || COMPILE_TEST
1024         depends on RESET_CONTROLLER
1025         help
1026           This enables using the SPI controller on the Allwinner A31 SoCs.
1027
1028 config SPI_SUNPLUS_SP7021
1029         tristate "Sunplus SP7021 SPI controller"
1030         depends on SOC_SP7021 || COMPILE_TEST
1031         help
1032           This enables Sunplus SP7021 SPI controller driver on the SP7021 SoCs.
1033           This driver can also be built as a module. If so, the module will be
1034           called as spi-sunplus-sp7021.
1035
1036           If you have a  Sunplus SP7021 platform say Y here.
1037           If unsure, say N.
1038
1039 config SPI_SYNQUACER
1040         tristate "Socionext's SynQuacer HighSpeed SPI controller"
1041         depends on ARCH_SYNQUACER || COMPILE_TEST
1042         help
1043           SPI driver for Socionext's High speed SPI controller which provides
1044           various operating modes for interfacing to serial peripheral devices
1045           that use the de-facto standard SPI protocol.
1046
1047           It also supports the new dual-bit and quad-bit SPI protocol.
1048
1049 config SPI_MXIC
1050         tristate "Macronix MX25F0A SPI controller"
1051         depends on SPI_MASTER
1052         imply MTD_NAND_ECC_MXIC
1053         help
1054           This selects the Macronix MX25F0A SPI controller driver.
1055
1056 config SPI_MXS
1057         tristate "Freescale MXS SPI controller"
1058         depends on ARCH_MXS
1059         select STMP_DEVICE
1060         help
1061           SPI driver for Freescale MXS devices.
1062
1063 config SPI_TEGRA210_QUAD
1064         tristate "NVIDIA Tegra QSPI Controller"
1065         depends on ARCH_TEGRA || COMPILE_TEST
1066         depends on RESET_CONTROLLER
1067         help
1068           QSPI driver for NVIDIA Tegra QSPI Controller interface. This
1069           controller is different from the SPI controller and is available
1070           on Tegra SoCs starting from Tegra210.
1071
1072 config SPI_TEGRA114
1073         tristate "NVIDIA Tegra114 SPI Controller"
1074         depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
1075         depends on RESET_CONTROLLER
1076         help
1077           SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
1078           is different than the older SoCs SPI controller and also register interface
1079           get changed with this controller.
1080
1081 config SPI_TEGRA20_SFLASH
1082         tristate "Nvidia Tegra20 Serial flash Controller"
1083         depends on ARCH_TEGRA || COMPILE_TEST
1084         depends on RESET_CONTROLLER
1085         help
1086           SPI driver for Nvidia Tegra20 Serial flash Controller interface.
1087           The main usecase of this controller is to use spi flash as boot
1088           device.
1089
1090 config SPI_TEGRA20_SLINK
1091         tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
1092         depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
1093         depends on RESET_CONTROLLER
1094         help
1095           SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
1096
1097 config SPI_THUNDERX
1098         tristate "Cavium ThunderX SPI controller"
1099         depends on PCI && 64BIT && (ARM64 || COMPILE_TEST)
1100         help
1101           SPI host driver for the hardware found on Cavium ThunderX
1102           SOCs.
1103
1104 config SPI_TOPCLIFF_PCH
1105         tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
1106         depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
1107         help
1108           SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
1109           used in some x86 embedded processors.
1110
1111           This driver also supports the ML7213/ML7223/ML7831, a companion chip
1112           for the Atom E6xx series and compatible with the Intel EG20T PCH.
1113
1114 config SPI_UNIPHIER
1115         tristate "Socionext UniPhier SPI Controller"
1116         depends on (ARCH_UNIPHIER || COMPILE_TEST) && OF
1117         depends on HAS_IOMEM
1118         help
1119           This enables a driver for the Socionext UniPhier SoC SCSSI SPI controller.
1120
1121           UniPhier SoCs have SCSSI and MCSSI SPI controllers.
1122           Every UniPhier SoC has SCSSI which supports single channel.
1123           Older UniPhier Pro4/Pro5 also has MCSSI which support multiple channels.
1124           This driver supports SCSSI only.
1125
1126           If your SoC supports SCSSI, say Y here.
1127
1128 config SPI_XCOMM
1129         tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
1130         depends on I2C
1131         help
1132           Support for the SPI-I2C bridge found on the Analog Devices
1133           AD-FMCOMMS1-EBZ board.
1134
1135 config SPI_XILINX
1136         tristate "Xilinx SPI controller common module"
1137         depends on HAS_IOMEM
1138         select SPI_BITBANG
1139         help
1140           This exposes the SPI controller IP from the Xilinx EDK.
1141
1142           See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
1143           Product Specification document (DS464) for hardware details.
1144
1145           Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
1146
1147 config SPI_XLP
1148         tristate "Cavium ThunderX2 SPI controller driver"
1149         depends on ARCH_THUNDER2 || COMPILE_TEST
1150         help
1151           Enable support for the SPI controller on the Cavium ThunderX2.
1152           (Originally on Netlogic XLP SoCs.)
1153
1154           If you have a Cavium ThunderX2 platform say Y here.
1155           If unsure, say N.
1156
1157 config SPI_XTENSA_XTFPGA
1158         tristate "Xtensa SPI controller for xtfpga"
1159         depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
1160         select SPI_BITBANG
1161         help
1162           SPI driver for xtfpga SPI master controller.
1163
1164           This simple SPI master controller is built into xtfpga bitstreams
1165           and is used to control daughterboard audio codec. It always transfers
1166           16 bit words in SPI mode 0, automatically asserting CS on transfer
1167           start and deasserting on end.
1168
1169 config SPI_ZYNQ_QSPI
1170         tristate "Xilinx Zynq QSPI controller"
1171         depends on ARCH_ZYNQ || COMPILE_TEST
1172         help
1173           This enables support for the Zynq Quad SPI controller
1174           in master mode.
1175           This controller only supports SPI memory interface.
1176
1177 config SPI_ZYNQMP_GQSPI
1178         tristate "Xilinx ZynqMP GQSPI controller"
1179         depends on (SPI_MASTER && HAS_DMA) || COMPILE_TEST
1180         help
1181           Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
1182
1183 config SPI_AMD
1184         tristate "AMD SPI controller"
1185         depends on SPI_MASTER || COMPILE_TEST
1186         help
1187           Enables SPI controller driver for AMD SoC.
1188
1189 #
1190 # Add new SPI master controllers in alphabetical order above this line
1191 #
1192
1193 comment "SPI Multiplexer support"
1194
1195 config SPI_MUX
1196         tristate "SPI multiplexer support"
1197         select MULTIPLEXER
1198         help
1199           This adds support for SPI multiplexers. Each SPI mux will be
1200           accessible as a SPI controller, the devices behind the mux will appear
1201           to be chip selects on this controller. It is still necessary to
1202           select one or more specific mux-controller drivers.
1203
1204 #
1205 # There are lots of SPI device types, with sensors and memory
1206 # being probably the most widely used ones.
1207 #
1208 comment "SPI Protocol Masters"
1209
1210 config SPI_SPIDEV
1211         tristate "User mode SPI device driver support"
1212         help
1213           This supports user mode SPI protocol drivers.
1214
1215 config SPI_LOOPBACK_TEST
1216         tristate "spi loopback test framework support"
1217         depends on m
1218         help
1219           This enables the SPI loopback testing framework driver
1220
1221           primarily used for development of spi_master drivers
1222           and to detect regressions
1223
1224 config SPI_TLE62X0
1225         tristate "Infineon TLE62X0 (for power switching)"
1226         depends on SYSFS
1227         help
1228           SPI driver for Infineon TLE62X0 series line driver chips,
1229           such as the TLE6220, TLE6230 and TLE6240.  This provides a
1230           sysfs interface, with each line presented as a kind of GPIO
1231           exposing both switch control and diagnostic feedback.
1232
1233 #
1234 # Add new SPI protocol masters in alphabetical order above this line
1235 #
1236
1237 endif # SPI_MASTER
1238
1239 #
1240 # SLAVE side ... listening to other SPI masters
1241 #
1242
1243 config SPI_SLAVE
1244         bool "SPI slave protocol handlers"
1245         help
1246           If your system has a slave-capable SPI controller, you can enable
1247           slave protocol handlers.
1248
1249 if SPI_SLAVE
1250
1251 config SPI_SLAVE_TIME
1252         tristate "SPI slave handler reporting boot up time"
1253         help
1254           SPI slave handler responding with the time of reception of the last
1255           SPI message.
1256
1257 config SPI_SLAVE_SYSTEM_CONTROL
1258         tristate "SPI slave handler controlling system state"
1259         help
1260           SPI slave handler to allow remote control of system reboot, power
1261           off, halt, and suspend.
1262
1263 endif # SPI_SLAVE
1264
1265 config SPI_DYNAMIC
1266         def_bool ACPI || OF_DYNAMIC || SPI_SLAVE
1267
1268 endif # SPI