include/configs/B4860QDS.h

   1 /*
   2  * Copyright 2011-2012 Freescale Semiconductor, Inc.
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #ifndef __CONFIG_H
   8 #define __CONFIG_H
   9
  10 /*
  11  * B4860 QDS board configuration file
  12  */
  13 #define CONFIG_B4860QDS
  14 #define CONFIG_PHYS_64BIT
  15
  16 #ifdef CONFIG_RAMBOOT_PBL
  17 #define CONFIG_RAMBOOT_TEXT_BASE        CONFIG_SYS_TEXT_BASE
  18 #define CONFIG_RESET_VECTOR_ADDRESS     0xfffffffc
  19 #define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/b4860qds/b4_pbi.cfg
  20 #define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/b4860qds/b4_rcw.cfg
  21 #endif
  22
  23 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
  24 /* Set 1M boot space */
  25 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
  26 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
  27                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
  28 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
  29 #define CONFIG_SYS_NO_FLASH
  30 #endif
  31
  32 /* High Level Configuration Options */
  33 #define CONFIG_BOOKE
  34 #define CONFIG_E500                     /* BOOKE e500 family */
  35 #define CONFIG_E500MC                   /* BOOKE e500mc family */
  36 #define CONFIG_SYS_BOOK3E_HV            /* Category E.HV supported */
  37 #define CONFIG_MPC85xx                  /* MPC85xx/PQ3 platform */
  38 #define CONFIG_MP                       /* support multiple processors */
  39
  40 #ifndef CONFIG_SYS_TEXT_BASE
  41 #define CONFIG_SYS_TEXT_BASE    0xeff80000
  42 #endif
  43
  44 #ifndef CONFIG_RESET_VECTOR_ADDRESS
  45 #define CONFIG_RESET_VECTOR_ADDRESS     0xeffffffc
  46 #endif
  47
  48 #define CONFIG_SYS_FSL_CPC              /* Corenet Platform Cache */
  49 #define CONFIG_SYS_NUM_CPC              CONFIG_NUM_DDR_CONTROLLERS
  50 #define CONFIG_FSL_IFC                  /* Enable IFC Support */
  51 #define CONFIG_PCI                      /* Enable PCI/PCIE */
  52 #define CONFIG_PCIE1                    /* PCIE controler 1 */
  53 #define CONFIG_FSL_PCI_INIT             /* Use common FSL init code */
  54 #define CONFIG_SYS_PCI_64BIT            /* enable 64-bit PCI resources */
  55
  56 #ifndef CONFIG_PPC_B4420
  57 #define CONFIG_SYS_SRIO
  58 #define CONFIG_SRIO1                    /* SRIO port 1 */
  59 #define CONFIG_SRIO2                    /* SRIO port 2 */
  60 #define CONFIG_SRIO_PCIE_BOOT_MASTER
  61 #endif
  62
  63 #define CONFIG_FSL_LAW                  /* Use common FSL init code */
  64
  65 /* I2C bus multiplexer */
  66 #define I2C_MUX_PCA_ADDR                0x77
  67
  68 /* VSC Crossbar switches */
  69 #define CONFIG_VSC_CROSSBAR
  70 #define I2C_CH_DEFAULT                  0x8
  71 #define I2C_CH_VSC3316                  0xc
  72 #define I2C_CH_VSC3308                  0xd
  73
  74 #define VSC3316_TX_ADDRESS              0x70
  75 #define VSC3316_RX_ADDRESS              0x71
  76 #define VSC3308_TX_ADDRESS              0x02
  77 #define VSC3308_RX_ADDRESS              0x03
  78
  79 /* IDT clock synthesizers */
  80 #define CONFIG_IDT8T49N222A
  81 #define I2C_CH_IDT                     0x9
  82
  83 #define IDT_SERDES1_ADDRESS            0x6E
  84 #define IDT_SERDES2_ADDRESS            0x6C
  85
  86 #define CONFIG_ENV_OVERWRITE
  87
  88 #ifdef CONFIG_SYS_NO_FLASH
  89 #if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
  90 #define CONFIG_ENV_IS_NOWHERE
  91 #endif
  92 #else
  93 #define CONFIG_FLASH_CFI_DRIVER
  94 #define CONFIG_SYS_FLASH_CFI
  95 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
  96 #endif
  97
  98 #if defined(CONFIG_SPIFLASH)
  99 #define CONFIG_SYS_EXTRA_ENV_RELOC
 100 #define CONFIG_ENV_IS_IN_SPI_FLASH
 101 #define CONFIG_ENV_SPI_BUS              0
 102 #define CONFIG_ENV_SPI_CS               0
 103 #define CONFIG_ENV_SPI_MAX_HZ           10000000
 104 #define CONFIG_ENV_SPI_MODE             0
 105 #define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
 106 #define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
 107 #define CONFIG_ENV_SECT_SIZE            0x10000
 108 #elif defined(CONFIG_SDCARD)
 109 #define CONFIG_SYS_EXTRA_ENV_RELOC
 110 #define CONFIG_ENV_IS_IN_MMC
 111 #define CONFIG_SYS_MMC_ENV_DEV          0
 112 #define CONFIG_ENV_SIZE                 0x2000
 113 #define CONFIG_ENV_OFFSET               (512 * 1097)
 114 #elif defined(CONFIG_NAND)
 115 #define CONFIG_SYS_EXTRA_ENV_RELOC
 116 #define CONFIG_ENV_IS_IN_NAND
 117 #define CONFIG_ENV_SIZE                 CONFIG_SYS_NAND_BLOCK_SIZE
 118 #define CONFIG_ENV_OFFSET               (5 * CONFIG_SYS_NAND_BLOCK_SIZE)
 119 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 120 #define CONFIG_ENV_IS_IN_REMOTE
 121 #define CONFIG_ENV_ADDR         0xffe20000
 122 #define CONFIG_ENV_SIZE         0x2000
 123 #elif defined(CONFIG_ENV_IS_NOWHERE)
 124 #define CONFIG_ENV_SIZE         0x2000
 125 #else
 126 #define CONFIG_ENV_IS_IN_FLASH
 127 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 128 #define CONFIG_ENV_SIZE         0x2000
 129 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K (one sector) */
 130 #endif
 131
 132 #ifndef __ASSEMBLY__
 133 unsigned long get_board_sys_clk(void);
 134 unsigned long get_board_ddr_clk(void);
 135 #endif
 136 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk() /* sysclk for MPC85xx */
 137 #define CONFIG_DDR_CLK_FREQ     get_board_ddr_clk()
 138
 139 /*
 140  * These can be toggled for performance analysis, otherwise use default.
 141  */
 142 #define CONFIG_SYS_CACHE_STASHING
 143 #define CONFIG_BTB                      /* toggle branch predition */
 144 #define CONFIG_DDR_ECC
 145 #ifdef CONFIG_DDR_ECC
 146 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
 147 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
 148 #endif
 149
 150 #define CONFIG_ENABLE_36BIT_PHYS
 151
 152 #ifdef CONFIG_PHYS_64BIT
 153 #define CONFIG_ADDR_MAP
 154 #define CONFIG_SYS_NUM_ADDR_MAP         64      /* number of TLB1 entries */
 155 #endif
 156
 157 #if 0
 158 #define CONFIG_POST CONFIG_SYS_POST_MEMORY      /* test POST memory test */
 159 #endif
 160 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest works on */
 161 #define CONFIG_SYS_MEMTEST_END          0x00400000
 162 #define CONFIG_SYS_ALT_MEMTEST
 163 #define CONFIG_PANIC_HANG       /* do not reset board on panic */
 164
 165 /*
 166  *  Config the L3 Cache as L3 SRAM
 167  */
 168 #define CONFIG_SYS_INIT_L3_ADDR         CONFIG_RAMBOOT_TEXT_BASE
 169
 170 #ifdef CONFIG_PHYS_64BIT
 171 #define CONFIG_SYS_DCSRBAR              0xf0000000
 172 #define CONFIG_SYS_DCSRBAR_PHYS         0xf00000000ull
 173 #endif
 174
 175 /* EEPROM */
 176 #define CONFIG_SYS_I2C_EEPROM_NXID
 177 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 178 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x57
 179 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 180 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 181 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
 182
 183 /*
 184  * DDR Setup
 185  */
 186 #define CONFIG_VERY_BIG_RAM
 187 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
 188 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
 189
 190 /* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
 191 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 192 #define CONFIG_CHIP_SELECTS_PER_CTRL    (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 193
 194 #define CONFIG_DDR_SPD
 195 #define CONFIG_SYS_DDR_RAW_TIMING
 196 #define CONFIG_FSL_DDR3
 197 #define CONFIG_FSL_DDR_INTERACTIVE
 198
 199 #define CONFIG_SYS_SPD_BUS_NUM  0
 200 #define SPD_EEPROM_ADDRESS1     0x51
 201 #define SPD_EEPROM_ADDRESS2     0x53
 202
 203 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
 204 #define CONFIG_SYS_SDRAM_SIZE   2048    /* for fixed parameter use */
 205
 206 /*
 207  * IFC Definitions
 208  */
 209 #define CONFIG_SYS_FLASH_BASE   0xe0000000
 210 #ifdef CONFIG_PHYS_64BIT
 211 #define CONFIG_SYS_FLASH_BASE_PHYS      (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
 212 #else
 213 #define CONFIG_SYS_FLASH_BASE_PHYS      CONFIG_SYS_FLASH_BASE
 214 #endif
 215
 216 #define CONFIG_SYS_NOR0_CSPR_EXT        (0xf)
 217 #define CONFIG_SYS_NOR0_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
 218                                 + 0x8000000) | \
 219                                 CSPR_PORT_SIZE_16 | \
 220                                 CSPR_MSEL_NOR | \
 221                                 CSPR_V)
 222 #define CONFIG_SYS_NOR1_CSPR_EXT        (0xf)
 223 #define CONFIG_SYS_NOR1_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
 224                                 CSPR_PORT_SIZE_16 | \
 225                                 CSPR_MSEL_NOR | \
 226                                 CSPR_V)
 227 #define CONFIG_SYS_NOR_AMASK    IFC_AMASK(128 * 1024 * 1024)
 228 /* NOR Flash Timing Params */
 229 #define CONFIG_SYS_NOR_CSOR     CSOR_NOR_ADM_SHIFT(4)
 230 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x01) | \
 231                                 FTIM0_NOR_TEADC(0x04) | \
 232                                 FTIM0_NOR_TEAHC(0x20))
 233 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 234                                 FTIM1_NOR_TRAD_NOR(0x1A) |\
 235                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 236 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x01) | \
 237                                 FTIM2_NOR_TCH(0x0E) | \
 238                                 FTIM2_NOR_TWPH(0x0E) | \
 239                                 FTIM2_NOR_TWP(0x1c))
 240 #define CONFIG_SYS_NOR_FTIM3    0x0
 241
 242 #define CONFIG_SYS_FLASH_QUIET_TEST
 243 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 244
 245 #define CONFIG_SYS_MAX_FLASH_BANKS      2       /* number of banks */
 246 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 247 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 248 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 249
 250 #define CONFIG_SYS_FLASH_EMPTY_INFO
 251 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE_PHYS \
 252                                         + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
 253
 254 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 255 #define CONFIG_FSL_QIXIS_V2
 256 #define QIXIS_BASE              0xffdf0000
 257 #ifdef CONFIG_PHYS_64BIT
 258 #define QIXIS_BASE_PHYS         (0xf00000000ull | QIXIS_BASE)
 259 #else
 260 #define QIXIS_BASE_PHYS         QIXIS_BASE
 261 #endif
 262 #define QIXIS_LBMAP_SWITCH              0x01
 263 #define QIXIS_LBMAP_MASK                0x0f
 264 #define QIXIS_LBMAP_SHIFT               0
 265 #define QIXIS_LBMAP_DFLTBANK            0x00
 266 #define QIXIS_LBMAP_ALTBANK             0x02
 267 #define QIXIS_RST_CTL_RESET             0x31
 268 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 269 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 270 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 271
 272 #define CONFIG_SYS_CSPR3_EXT    (0xf)
 273 #define CONFIG_SYS_CSPR3        (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
 274                                 | CSPR_PORT_SIZE_8 \
 275                                 | CSPR_MSEL_GPCM \
 276                                 | CSPR_V)
 277 #define CONFIG_SYS_AMASK3       IFC_AMASK(4 * 1024)
 278 #define CONFIG_SYS_CSOR3        0x0
 279 /* QIXIS Timing parameters for IFC CS3 */
 280 #define CONFIG_SYS_CS3_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 281                                         FTIM0_GPCM_TEADC(0x0e) | \
 282                                         FTIM0_GPCM_TEAHC(0x0e))
 283 #define CONFIG_SYS_CS3_FTIM1            (FTIM1_GPCM_TACO(0x0e) | \
 284                                         FTIM1_GPCM_TRAD(0x1f))
 285 #define CONFIG_SYS_CS3_FTIM2            (FTIM2_GPCM_TCS(0x0e) | \
 286                                         FTIM2_GPCM_TCH(0x0) | \
 287                                         FTIM2_GPCM_TWP(0x1f))
 288 #define CONFIG_SYS_CS3_FTIM3            0x0
 289
 290 /* NAND Flash on IFC */
 291 #define CONFIG_NAND_FSL_IFC
 292 #define CONFIG_SYS_NAND_BASE            0xff800000
 293 #ifdef CONFIG_PHYS_64BIT
 294 #define CONFIG_SYS_NAND_BASE_PHYS       (0xf00000000ull | CONFIG_SYS_NAND_BASE)
 295 #else
 296 #define CONFIG_SYS_NAND_BASE_PHYS       CONFIG_SYS_NAND_BASE
 297 #endif
 298
 299 #define CONFIG_SYS_NAND_CSPR_EXT        (0xf)
 300 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 301                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 302                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 303                                 | CSPR_V)
 304 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64 * 1024)
 305
 306 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 307                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 308                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 309                                 | CSOR_NAND_RAL_3       /* RAL = 2Byes */ \
 310                                 | CSOR_NAND_PGS_2K      /* Page Size = 2K */ \
 311                                 | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
 312                                 | CSOR_NAND_PB(64))     /*Pages Per Block = 64*/
 313
 314 #define CONFIG_SYS_NAND_ONFI_DETECTION
 315
 316 /* ONFI NAND Flash mode0 Timing Params */
 317 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x07) | \
 318                                         FTIM0_NAND_TWP(0x18)   | \
 319                                         FTIM0_NAND_TWCHT(0x07) | \
 320                                         FTIM0_NAND_TWH(0x0a))
 321 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x32) | \
 322                                         FTIM1_NAND_TWBE(0x39)  | \
 323                                         FTIM1_NAND_TRR(0x0e)   | \
 324                                         FTIM1_NAND_TRP(0x18))
 325 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x0f) | \
 326                                         FTIM2_NAND_TREH(0x0a) | \
 327                                         FTIM2_NAND_TWHRE(0x1e))
 328 #define CONFIG_SYS_NAND_FTIM3           0x0
 329
 330 #define CONFIG_SYS_NAND_DDR_LAW         11
 331
 332 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 333 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 334 #define CONFIG_MTD_NAND_VERIFY_WRITE
 335 #define CONFIG_CMD_NAND
 336
 337 #define CONFIG_SYS_NAND_BLOCK_SIZE      (128 * 1024)
 338
 339 #if defined(CONFIG_NAND)
 340 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 341 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 342 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 343 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 344 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 345 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 346 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 347 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 348 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 349 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR0_CSPR
 350 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
 351 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
 352 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
 353 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
 354 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
 355 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
 356 #else
 357 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 358 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR
 359 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 360 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 361 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 362 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 363 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 364 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 365 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NAND_CSPR_EXT
 366 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NAND_CSPR
 367 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NAND_AMASK
 368 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NAND_CSOR
 369 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NAND_FTIM0
 370 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NAND_FTIM1
 371 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NAND_FTIM2
 372 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NAND_FTIM3
 373 #endif
 374 #define CONFIG_SYS_CSPR1_EXT            CONFIG_SYS_NOR1_CSPR_EXT
 375 #define CONFIG_SYS_CSPR1                CONFIG_SYS_NOR1_CSPR
 376 #define CONFIG_SYS_AMASK1               CONFIG_SYS_NOR_AMASK
 377 #define CONFIG_SYS_CSOR1                CONFIG_SYS_NOR_CSOR
 378 #define CONFIG_SYS_CS1_FTIM0            CONFIG_SYS_NOR_FTIM0
 379 #define CONFIG_SYS_CS1_FTIM1            CONFIG_SYS_NOR_FTIM1
 380 #define CONFIG_SYS_CS1_FTIM2            CONFIG_SYS_NOR_FTIM2
 381 #define CONFIG_SYS_CS1_FTIM3            CONFIG_SYS_NOR_FTIM3
 382
 383 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
 384
 385 #if defined(CONFIG_RAMBOOT_PBL)
 386 #define CONFIG_SYS_RAMBOOT
 387 #endif
 388
 389 #define CONFIG_BOARD_EARLY_INIT_R
 390 #define CONFIG_MISC_INIT_R
 391
 392 #define CONFIG_HWCONFIG
 393
 394 /* define to use L1 as initial stack */
 395 #define CONFIG_L1_INIT_RAM
 396 #define CONFIG_SYS_INIT_RAM_LOCK
 397 #define CONFIG_SYS_INIT_RAM_ADDR        0xfdd00000      /* Initial L1 address */
 398 #ifdef CONFIG_PHYS_64BIT
 399 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH      0xf
 400 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW       0xfe0ec000
 401 /* The assembler doesn't like typecast */
 402 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
 403         ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
 404           CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
 405 #else
 406 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS   0xfe0ec000 /* Initial L1 address */
 407 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
 408 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
 409 #endif
 410 #define CONFIG_SYS_INIT_RAM_SIZE                0x00004000
 411
 412 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 413                                         GENERATED_GBL_DATA_SIZE)
 414 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 415
 416 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)
 417 #define CONFIG_SYS_MALLOC_LEN           (4 * 1024 * 1024)
 418
 419 /* Serial Port - controlled on board with jumper J8
 420  * open - index 2
 421  * shorted - index 1
 422  */
 423 #define CONFIG_CONS_INDEX       1
 424 #define CONFIG_SYS_NS16550
 425 #define CONFIG_SYS_NS16550_SERIAL
 426 #define CONFIG_SYS_NS16550_REG_SIZE     1
 427 #define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)
 428
 429 #define CONFIG_SYS_BAUDRATE_TABLE       \
 430         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 431
 432 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
 433 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
 434 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
 435 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
 436 #define CONFIG_SERIAL_MULTI             /* Enable both serial ports */
 437 #define CONFIG_SYS_CONSOLE_IS_IN_ENV    /* determine from environment */
 438
 439
 440 /* Use the HUSH parser */
 441 #define CONFIG_SYS_HUSH_PARSER
 442 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 443
 444 /* pass open firmware flat tree */
 445 #define CONFIG_OF_LIBFDT
 446 #define CONFIG_OF_BOARD_SETUP
 447 #define CONFIG_OF_STDOUT_VIA_ALIAS
 448
 449 /* new uImage format support */
 450 #define CONFIG_FIT
 451 #define CONFIG_FIT_VERBOSE      /* enable fit_format_{error,warning}() */
 452
 453 /* I2C */
 454 #define CONFIG_SYS_I2C
 455 #define CONFIG_SYS_I2C_FSL              /* Use FSL common I2C driver */
 456 #define CONFIG_SYS_FSL_I2C_SPEED        400000  /* I2C speed in Hz */
 457 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 458 #define CONFIG_SYS_FSL_I2C2_SPEED       400000  /* I2C speed in Hz */
 459 #define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
 460 #define CONFIG_SYS_FSL_I2C_OFFSET       0x118000
 461 #define CONFIG_SYS_FSL_I2C2_OFFSET      0x119000
 462
 463 /*
 464  * RTC configuration
 465  */
 466 #define RTC
 467 #define CONFIG_RTC_DS3231               1
 468 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 469
 470 /*
 471  * RapidIO
 472  */
 473 #ifdef CONFIG_SYS_SRIO
 474 #ifdef CONFIG_SRIO1
 475 #define CONFIG_SYS_SRIO1_MEM_VIRT       0xa0000000
 476 #ifdef CONFIG_PHYS_64BIT
 477 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xc20000000ull
 478 #else
 479 #define CONFIG_SYS_SRIO1_MEM_PHYS       0xa0000000
 480 #endif
 481 #define CONFIG_SYS_SRIO1_MEM_SIZE       0x10000000      /* 256M */
 482 #endif
 483
 484 #ifdef CONFIG_SRIO2
 485 #define CONFIG_SYS_SRIO2_MEM_VIRT       0xb0000000
 486 #ifdef CONFIG_PHYS_64BIT
 487 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xc30000000ull
 488 #else
 489 #define CONFIG_SYS_SRIO2_MEM_PHYS       0xb0000000
 490 #endif
 491 #define CONFIG_SYS_SRIO2_MEM_SIZE       0x10000000      /* 256M */
 492 #endif
 493 #endif
 494
 495 /*
 496  * for slave u-boot IMAGE instored in master memory space,
 497  * PHYS must be aligned based on the SIZE
 498  */
 499 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
 500 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
 501 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x80000        /* 512K */
 502 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
 503 /*
 504  * for slave UCODE and ENV instored in master memory space,
 505  * PHYS must be aligned based on the SIZE
 506  */
 507 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
 508 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
 509 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000    /* 256K */
 510
 511 /* slave core release by master*/
 512 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
 513 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
 514
 515 /*
 516  * SRIO_PCIE_BOOT - SLAVE
 517  */
 518 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
 519 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
 520 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
 521                 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
 522 #endif
 523
 524 /*
 525  * eSPI - Enhanced SPI
 526  */
 527 #define CONFIG_FSL_ESPI
 528 #define CONFIG_SPI_FLASH
 529 #define CONFIG_SPI_FLASH_SST
 530 #define CONFIG_CMD_SF
 531 #define CONFIG_SF_DEFAULT_SPEED         10000000
 532 #define CONFIG_SF_DEFAULT_MODE          0
 533
 534 /*
 535  * MAPLE
 536  */
 537 #ifdef CONFIG_PHYS_64BIT
 538 #define CONFIG_SYS_MAPLE_MEM_PHYS      0xFA0000000ull
 539 #else
 540 #define CONFIG_SYS_MAPLE_MEM_PHYS      0xA0000000
 541 #endif
 542
 543 /*
 544  * General PCI
 545  * Memory space is mapped 1-1, but I/O space must start from 0.
 546  */
 547
 548 /* controller 1, direct to uli, tgtid 3, Base address 20000 */
 549 #define CONFIG_SYS_PCIE1_MEM_VIRT       0x80000000
 550 #ifdef CONFIG_PHYS_64BIT
 551 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 552 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc00000000ull
 553 #else
 554 #define CONFIG_SYS_PCIE1_MEM_BUS        0x80000000
 555 #define CONFIG_SYS_PCIE1_MEM_PHYS       0x80000000
 556 #endif
 557 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 558 #define CONFIG_SYS_PCIE1_IO_VIRT        0xf8000000
 559 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 560 #ifdef CONFIG_PHYS_64BIT
 561 #define CONFIG_SYS_PCIE1_IO_PHYS        0xff8000000ull
 562 #else
 563 #define CONFIG_SYS_PCIE1_IO_PHYS        0xf8000000
 564 #endif
 565 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 566
 567 /* Qman/Bman */
 568 #ifndef CONFIG_NOBQFMAN
 569 #define CONFIG_SYS_DPAA_QBMAN           /* Support Q/Bman */
 570 #define CONFIG_SYS_BMAN_NUM_PORTALS     25
 571 #define CONFIG_SYS_BMAN_MEM_BASE        0xf4000000
 572 #ifdef CONFIG_PHYS_64BIT
 573 #define CONFIG_SYS_BMAN_MEM_PHYS        0xff4000000ull
 574 #else
 575 #define CONFIG_SYS_BMAN_MEM_PHYS        CONFIG_SYS_BMAN_MEM_BASE
 576 #endif
 577 #define CONFIG_SYS_BMAN_MEM_SIZE        0x02000000
 578 #define CONFIG_SYS_QMAN_NUM_PORTALS     25
 579 #define CONFIG_SYS_QMAN_MEM_BASE        0xf6000000
 580 #ifdef CONFIG_PHYS_64BIT
 581 #define CONFIG_SYS_QMAN_MEM_PHYS        0xff6000000ull
 582 #else
 583 #define CONFIG_SYS_QMAN_MEM_PHYS        CONFIG_SYS_QMAN_MEM_BASE
 584 #endif
 585 #define CONFIG_SYS_QMAN_MEM_SIZE        0x02000000
 586
 587 #define CONFIG_SYS_DPAA_FMAN
 588
 589 #define CONFIG_SYS_DPAA_RMAN
 590
 591 /* Default address of microcode for the Linux Fman driver */
 592 #if defined(CONFIG_SPIFLASH)
 593 /*
 594  * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
 595  * env, so we got 0x110000.
 596  */
 597 #define CONFIG_SYS_QE_FW_IN_SPIFLASH
 598 #define CONFIG_SYS_QE_FMAN_FW_ADDR      0x110000
 599 #elif defined(CONFIG_SDCARD)
 600 /*
 601  * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
 602  * about 545KB (1089 blocks), Env is stored after the image, and the env size is
 603  * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
 604  */
 605 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC
 606 #define CONFIG_SYS_QE_FMAN_FW_ADDR      (512 * 1130)
 607 #elif defined(CONFIG_NAND)
 608 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND
 609 #define CONFIG_SYS_QE_FMAN_FW_ADDR      (6 * CONFIG_SYS_NAND_BLOCK_SIZE)
 610 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
 611 /*
 612  * Slave has no ucode locally, it can fetch this from remote. When implementing
 613  * in two corenet boards, slave's ucode could be stored in master's memory
 614  * space, the address can be mapped from slave TLB->slave LAW->
 615  * slave SRIO or PCIE outbound window->master inbound window->
 616  * master LAW->the ucode address in master's memory space.
 617  */
 618 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
 619 #define CONFIG_SYS_QE_FMAN_FW_ADDR      0xFFE00000
 620 #else
 621 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR
 622 #define CONFIG_SYS_QE_FMAN_FW_ADDR              0xEFF40000
 623 #endif
 624 #define CONFIG_SYS_QE_FMAN_FW_LENGTH    0x10000
 625 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 626 #endif /* CONFIG_NOBQFMAN */
 627
 628 #ifdef CONFIG_SYS_DPAA_FMAN
 629 #define CONFIG_FMAN_ENET
 630 #define CONFIG_PHYLIB_10G
 631 #define CONFIG_PHY_VITESSE
 632 #define CONFIG_PHY_TERANETICS
 633 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C
 634 #define SGMII_CARD_PORT2_PHY_ADDR 0x10
 635 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E
 636 #define SGMII_CARD_PORT4_PHY_ADDR 0x11
 637 #endif
 638
 639 #ifdef CONFIG_PCI
 640 #define CONFIG_PCI_INDIRECT_BRIDGE
 641 #define CONFIG_NET_MULTI
 642 #define CONFIG_PCI_PNP                  /* do pci plug-and-play */
 643 #define CONFIG_E1000
 644
 645 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 646 #define CONFIG_DOS_PARTITION
 647 #endif  /* CONFIG_PCI */
 648
 649 #ifdef CONFIG_FMAN_ENET
 650 #define CONFIG_SYS_FM1_DTSEC5_PHY_ADDR  0x10
 651 #define CONFIG_SYS_FM1_DTSEC6_PHY_ADDR  0x11
 652
 653 /*B4860 QDS AMC2PEX-2S default PHY_ADDR */
 654 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0x7       /*SLOT 1*/
 655 #define CONFIG_SYS_FM1_10GEC2_PHY_ADDR 0x6       /*SLOT 2*/
 656
 657
 658 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR    0x1c
 659 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR    0x1d
 660 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR    0x1e
 661 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR    0x1f
 662
 663 #define CONFIG_MII              /* MII PHY management */
 664 #define CONFIG_ETHPRIME         "FM1@DTSEC1"
 665 #define CONFIG_PHY_GIGE         /* Include GbE speed/duplex detection */
 666 #endif
 667
 668 /*
 669  * Environment
 670  */
 671 #define CONFIG_LOADS_ECHO               /* echo on for serial download */
 672 #define CONFIG_SYS_LOADS_BAUD_CHANGE    /* allow baudrate change */
 673
 674 /*
 675  * Command line configuration.
 676  */
 677 #include <config_cmd_default.h>
 678
 679 #define CONFIG_CMD_DATE
 680 #define CONFIG_CMD_DHCP
 681 #define CONFIG_CMD_EEPROM
 682 #define CONFIG_CMD_ELF
 683 #define CONFIG_CMD_ERRATA
 684 #define CONFIG_CMD_GREPENV
 685 #define CONFIG_CMD_IRQ
 686 #define CONFIG_CMD_I2C
 687 #define CONFIG_CMD_MII
 688 #define CONFIG_CMD_PING
 689 #define CONFIG_CMD_REGINFO
 690 #define CONFIG_CMD_SETEXPR
 691
 692 #ifdef CONFIG_PCI
 693 #define CONFIG_CMD_PCI
 694 #define CONFIG_CMD_NET
 695 #endif
 696
 697 /*
 698 * USB
 699 */
 700 #define CONFIG_HAS_FSL_DR_USB
 701
 702 #ifdef CONFIG_HAS_FSL_DR_USB
 703 #define CONFIG_USB_EHCI
 704
 705 #ifdef CONFIG_USB_EHCI
 706 #define CONFIG_CMD_USB
 707 #define CONFIG_USB_STORAGE
 708 #define CONFIG_USB_EHCI_FSL
 709 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 710 #define CONFIG_CMD_EXT2
 711 #endif
 712 #endif
 713
 714 /*
 715  * Miscellaneous configurable options
 716  */
 717 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 718 #define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
 719 #define CONFIG_AUTO_COMPLETE                    /* add autocompletion support */
 720 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 721 #define CONFIG_SYS_PROMPT       "=> "           /* Monitor Command Prompt */
 722 #ifdef CONFIG_CMD_KGDB
 723 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 724 #else
 725 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
 726 #endif
 727 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 728 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 729 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
 730 #define CONFIG_SYS_HZ           1000            /* decrementer freq: 1ms ticks*/
 731
 732 /*
 733  * For booting Linux, the board info and command line data
 734  * have to be in the first 64 MB of memory, since this is
 735  * the maximum mapped by the Linux kernel during initialization.
 736  */
 737 #define CONFIG_SYS_BOOTMAPSZ    (64 << 20)      /* Initial map for Linux*/
 738 #define CONFIG_SYS_BOOTM_LEN    (64 << 20)      /* Increase max gunzip size */
 739
 740 #ifdef CONFIG_CMD_KGDB
 741 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 742 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 743 #endif
 744
 745 /*
 746  * Environment Configuration
 747  */
 748 #define CONFIG_ROOTPATH         "/opt/nfsroot"
 749 #define CONFIG_BOOTFILE         "uImage"
 750 #define CONFIG_UBOOTPATH        "u-boot.bin"    /* U-Boot image on TFTP server*/
 751
 752 /* default location for tftp and bootm */
 753 #define CONFIG_LOADADDR         1000000
 754
 755 #define CONFIG_BOOTDELAY        10      /* -1 disables auto-boot */
 756
 757 #define CONFIG_BAUDRATE 115200
 758
 759 #define __USB_PHY_TYPE  ulpi
 760
 761 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 762         "hwconfig=fsl_ddr:ctlr_intlv=null,"             \
 763         "bank_intlv=cs0_cs1;"                                   \
 764         "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
 765         "netdev=eth0\0"                                         \
 766         "uboot=" __stringify(CONFIG_UBOOTPATH) "\0"                     \
 767         "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"                     \
 768         "tftpflash=tftpboot $loadaddr $uboot && "               \
 769         "protect off $ubootaddr +$filesize && "                 \
 770         "erase $ubootaddr +$filesize && "                       \
 771         "cp.b $loadaddr $ubootaddr $filesize && "               \
 772         "protect on $ubootaddr +$filesize && "                  \
 773         "cmp.b $loadaddr $ubootaddr $filesize\0"                \
 774         "consoledev=ttyS0\0"                                    \
 775         "ramdiskaddr=2000000\0"                                 \
 776         "ramdiskfile=b4860qds/ramdisk.uboot\0"                  \
 777         "fdtaddr=c00000\0"                                      \
 778         "fdtfile=b4860qds/b4860qds.dtb\0"                               \
 779         "bdev=sda3\0"                                           \
 780         "c=ffe\0"
 781
 782 /* For emulation this causes u-boot to jump to the start of the proof point
 783    app code automatically */
 784 #define CONFIG_PROOF_POINTS                     \
 785  "setenv bootargs root=/dev/$bdev rw "          \
 786  "console=$consoledev,$baudrate $othbootargs;"  \
 787  "cpu 1 release 0x29000000 - - -;"              \
 788  "cpu 2 release 0x29000000 - - -;"              \
 789  "cpu 3 release 0x29000000 - - -;"              \
 790  "cpu 4 release 0x29000000 - - -;"              \
 791  "cpu 5 release 0x29000000 - - -;"              \
 792  "cpu 6 release 0x29000000 - - -;"              \
 793  "cpu 7 release 0x29000000 - - -;"              \
 794  "go 0x29000000"
 795
 796 #define CONFIG_HVBOOT   \
 797  "setenv bootargs config-addr=0x60000000; "     \
 798  "bootm 0x01000000 - 0x00f00000"
 799
 800 #define CONFIG_ALU                              \
 801  "setenv bootargs root=/dev/$bdev rw "          \
 802  "console=$consoledev,$baudrate $othbootargs;"  \
 803  "cpu 1 release 0x01000000 - - -;"              \
 804  "cpu 2 release 0x01000000 - - -;"              \
 805  "cpu 3 release 0x01000000 - - -;"              \
 806  "cpu 4 release 0x01000000 - - -;"              \
 807  "cpu 5 release 0x01000000 - - -;"              \
 808  "cpu 6 release 0x01000000 - - -;"              \
 809  "cpu 7 release 0x01000000 - - -;"              \
 810  "go 0x01000000"
 811
 812 #define CONFIG_LINUX                            \
 813  "setenv bootargs root=/dev/ram rw "            \
 814  "console=$consoledev,$baudrate $othbootargs;"  \
 815  "setenv ramdiskaddr 0x02000000;"               \
 816  "setenv fdtaddr 0x00c00000;"                   \
 817  "setenv loadaddr 0x1000000;"                   \
 818  "bootm $loadaddr $ramdiskaddr $fdtaddr"
 819
 820 #define CONFIG_HDBOOT                                   \
 821         "setenv bootargs root=/dev/$bdev rw "           \
 822         "console=$consoledev,$baudrate $othbootargs;"   \
 823         "tftp $loadaddr $bootfile;"                     \
 824         "tftp $fdtaddr $fdtfile;"                       \
 825         "bootm $loadaddr - $fdtaddr"
 826
 827 #define CONFIG_NFSBOOTCOMMAND                   \
 828         "setenv bootargs root=/dev/nfs rw "     \
 829         "nfsroot=$serverip:$rootpath "          \
 830         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 831         "console=$consoledev,$baudrate $othbootargs;"   \
 832         "tftp $loadaddr $bootfile;"             \
 833         "tftp $fdtaddr $fdtfile;"               \
 834         "bootm $loadaddr - $fdtaddr"
 835
 836 #define CONFIG_RAMBOOTCOMMAND                           \
 837         "setenv bootargs root=/dev/ram rw "             \
 838         "console=$consoledev,$baudrate $othbootargs;"   \
 839         "tftp $ramdiskaddr $ramdiskfile;"               \
 840         "tftp $loadaddr $bootfile;"                     \
 841         "tftp $fdtaddr $fdtfile;"                       \
 842         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 843
 844 #define CONFIG_BOOTCOMMAND              CONFIG_LINUX
 845
 846 #include <asm/fsl_secure_boot.h>
 847
 848 #endif  /* __CONFIG_H */