include/configs/MPC8610HPCD.h

   1 /*
   2  * Copyright 2007 Freescale Semiconductor, Inc.
   3  *
   4  * This program is free software; you can redistribute it and/or
   5  * modify it under the terms of the GNU General Public License
   6  * Version 2 as published by the Free Software Foundation.
   7  */
   8
   9 /*
  10  * MPC8610HPCD board configuration file
  11  */
  12
  13 #ifndef __CONFIG_H
  14 #define __CONFIG_H
  15
  16 /* High Level Configuration Options */
  17 #define CONFIG_MPC86xx          1       /* MPC86xx */
  18 #define CONFIG_MPC8610          1       /* MPC8610 specific */
  19 #define CONFIG_MPC8610HPCD      1       /* MPC8610HPCD board specific */
  20 #define CONFIG_LINUX_RESET_VEC  0x100   /* Reset vector used by Linux */
  21
  22 #define CONFIG_FSL_DIU_FB       1       /* FSL DIU */
  23
  24 /* video */
  25 #undef CONFIG_VIDEO
  26
  27 #if defined(CONFIG_VIDEO)
  28 #define CONFIG_CFB_CONSOLE
  29 #define CONFIG_VGA_AS_SINGLE_DEVICE
  30 #endif
  31
  32 #ifdef RUN_DIAG
  33 #define CONFIG_SYS_DIAG_ADDR            0xff800000
  34 #endif
  35
  36 /*
  37  * virtual address to be used for temporary mappings.  There
  38  * should be 128k free at this VA.
  39  */
  40 #define CONFIG_SYS_SCRATCH_VA   0xc0000000
  41
  42 #define CONFIG_PCI              1       /* Enable PCI/PCIE*/
  43 #define CONFIG_PCI1             1       /* PCI controler 1 */
  44 #define CONFIG_PCIE1            1       /* PCIe 1 connected to ULI bridge */
  45 #define CONFIG_PCIE2            1       /* PCIe 2 connected to slot */
  46 #define CONFIG_FSL_PCI_INIT     1       /* Use common FSL init code */
  47 #define CONFIG_SYS_PCI_64BIT    1       /* enable 64-bit PCI resources */
  48 #define CONFIG_FSL_LAW          1       /* Use common FSL init code */
  49
  50 #define CONFIG_ENV_OVERWRITE
  51 #define CONFIG_INTERRUPTS               /* enable pci, srio, ddr interrupts */
  52
  53 #define CONFIG_HIGH_BATS        1       /* High BATs supported & enabled */
  54 #define CONFIG_ALTIVEC          1
  55
  56 /*
  57  * L2CR setup -- make sure this is right for your board!
  58  */
  59 #define CONFIG_SYS_L2
  60 #define L2_INIT         0
  61 #define L2_ENABLE       (L2CR_L2E |0x00100000 )
  62
  63 #ifndef CONFIG_SYS_CLK_FREQ
  64 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk(0)
  65 #endif
  66
  67 #define CONFIG_BOARD_EARLY_INIT_F       1       /* Call board_pre_init */
  68 #define CONFIG_MISC_INIT_R              1
  69
  70 #define CONFIG_SYS_MEMTEST_START        0x00200000      /* memtest region */
  71 #define CONFIG_SYS_MEMTEST_END          0x00400000
  72
  73 /*
  74  * Base addresses -- Note these are effective addresses where the
  75  * actual resources get mapped (not physical addresses)
  76  */
  77 #define CONFIG_SYS_CCSRBAR_DEFAULT      0xff700000      /* CCSRBAR Default */
  78 #define CONFIG_SYS_CCSRBAR              0xe0000000      /* relocated CCSRBAR */
  79 #define CONFIG_SYS_IMMR         CONFIG_SYS_CCSRBAR      /* PQII uses CONFIG_SYS_IMMR */
  80
  81 #define CONFIG_SYS_CCSRBAR_PHYS_LOW     CONFIG_SYS_CCSRBAR
  82 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH    0x0
  83 #define CONFIG_SYS_CCSRBAR_PHYS         CONFIG_SYS_CCSRBAR_PHYS_LOW
  84
  85 #define CONFIG_SYS_DIU_ADDR             (CONFIG_SYS_CCSRBAR+0x2c000)
  86
  87 /* DDR Setup */
  88 #define CONFIG_FSL_DDR2
  89 #undef CONFIG_FSL_DDR_INTERACTIVE
  90 #define CONFIG_SPD_EEPROM               /* Use SPD for DDR */
  91 #define CONFIG_DDR_SPD
  92
  93 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER       /* DDR controller or DMA? */
  94 #define CONFIG_MEM_INIT_VALUE   0xDeadBeef
  95
  96 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000      /* DDR is system memory*/
  97 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  98 #define CONFIG_SYS_MAX_DDR_BAT_SIZE     0x80000000      /* BAT mapping size */
  99 #define CONFIG_VERY_BIG_RAM
 100
 101 #define CONFIG_NUM_DDR_CONTROLLERS      1
 102 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
 103 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
 104
 105 #define SPD_EEPROM_ADDRESS1     0x51    /* CTLR 0 DIMM 0 */
 106
 107 /* These are used when DDR doesn't use SPD.  */
 108 #define CONFIG_SYS_SDRAM_SIZE   256             /* DDR is 256MB */
 109
 110 #if 0 /* TODO */
 111 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F
 112 #define CONFIG_SYS_DDR_CS0_CONFIG       0x80010202      /* Enable, no interleaving */
 113 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
 114 #define CONFIG_SYS_DDR_TIMING_0 0x00260802
 115 #define CONFIG_SYS_DDR_TIMING_1 0x3935d322
 116 #define CONFIG_SYS_DDR_TIMING_2 0x14904cc8
 117 #define CONFIG_SYS_DDR_MODE_1           0x00480432
 118 #define CONFIG_SYS_DDR_MODE_2           0x00000000
 119 #define CONFIG_SYS_DDR_INTERVAL 0x06180100
 120 #define CONFIG_SYS_DDR_DATA_INIT        0xdeadbeef
 121 #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000
 122 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
 123 #define CONFIG_SYS_DDR_OCD_STATUS       0x00000000
 124 #define CONFIG_SYS_DDR_CONTROL          0xe3008000      /* Type = DDR2 */
 125 #define CONFIG_SYS_DDR_CONTROL2 0x04400010
 126
 127 #define CONFIG_SYS_DDR_ERR_INT_EN       0x00000000
 128 #define CONFIG_SYS_DDR_ERR_DIS          0x00000000
 129 #define CONFIG_SYS_DDR_SBE              0x000f0000
 130
 131 #endif
 132
 133
 134 #define CONFIG_ID_EEPROM
 135 #define CONFIG_SYS_I2C_EEPROM_NXID
 136 #define CONFIG_ID_EEPROM
 137 #define CONFIG_SYS_I2C_EEPROM_ADDR     0x57
 138 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 139
 140
 141 #define CONFIG_SYS_FLASH_BASE           0xf0000000 /* start of FLASH 128M */
 142 #define CONFIG_SYS_FLASH_BASE2          0xf8000000
 143
 144 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
 145
 146 #define CONFIG_SYS_BR0_PRELIM           0xf8001001 /* port size 16bit */
 147 #define CONFIG_SYS_OR0_PRELIM           0xf8006e65 /* 128MB NOR Flash*/
 148
 149 #define CONFIG_SYS_BR1_PRELIM           0xf0001001 /* port size 16bit */
 150 #define CONFIG_SYS_OR1_PRELIM           0xf8006e65 /* 128MB Promjet */
 151 #if 0 /* TODO */
 152 #define CONFIG_SYS_BR2_PRELIM           0xf0000000
 153 #define CONFIG_SYS_OR2_PRELIM           0xf0000000 /* 256MB NAND Flash - bank 1 */
 154 #endif
 155 #define CONFIG_SYS_BR3_PRELIM           0xe8000801 /* port size 8bit */
 156 #define CONFIG_SYS_OR3_PRELIM           0xfff06ff7 /* 1MB PIXIS area*/
 157
 158
 159 #define CONFIG_FSL_PIXIS        1       /* use common PIXIS code */
 160 #define PIXIS_BASE      0xe8000000      /* PIXIS registers */
 161 #define PIXIS_ID                0x0     /* Board ID at offset 0 */
 162 #define PIXIS_VER               0x1     /* Board version at offset 1 */
 163 #define PIXIS_PVER              0x2     /* PIXIS FPGA version at offset 2 */
 164 #define PIXIS_RST               0x4     /* PIXIS Reset Control register */
 165 #define PIXIS_AUX               0x6     /* PIXIS Auxiliary register; Scratch */
 166 #define PIXIS_SPD               0x7     /* Register for SYSCLK speed */
 167 #define PIXIS_BRDCFG0           0x8     /* PIXIS Board Configuration Register0*/
 168 #define PIXIS_VCTL              0x10    /* VELA Control Register */
 169 #define PIXIS_VCFGEN0           0x12    /* VELA Config Enable 0 */
 170 #define PIXIS_VCFGEN1           0x13    /* VELA Config Enable 1 */
 171 #define PIXIS_VBOOT             0x16    /* VELA VBOOT Register */
 172 #define PIXIS_VSPEED0           0x17    /* VELA VSpeed 0 */
 173 #define PIXIS_VSPEED1           0x18    /* VELA VSpeed 1 */
 174 #define PIXIS_VCLKH             0x19    /* VELA VCLKH register */
 175 #define PIXIS_VCLKL             0x1A    /* VELA VCLKL register */
 176 #define CONFIG_SYS_PIXIS_VBOOT_MASK     0xC0    /* Reset altbank mask */
 177
 178 #define CONFIG_SYS_MAX_FLASH_BANKS      2               /* number of banks */
 179 #define CONFIG_SYS_MAX_FLASH_SECT       1024            /* sectors per device */
 180
 181 #undef  CONFIG_SYS_FLASH_CHECKSUM
 182 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 183 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 184 #define CONFIG_SYS_MONITOR_BASE TEXT_BASE       /* start of monitor */
 185 #define CONFIG_SYS_MONITOR_BASE_EARLY   0xfff00000      /* early monitor loc */
 186
 187 #define CONFIG_FLASH_CFI_DRIVER
 188 #define CONFIG_SYS_FLASH_CFI
 189 #define CONFIG_SYS_FLASH_EMPTY_INFO
 190
 191 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 192 #define CONFIG_SYS_RAMBOOT
 193 #else
 194 #undef  CONFIG_SYS_RAMBOOT
 195 #endif
 196
 197 #if defined(CONFIG_SYS_RAMBOOT)
 198 #undef CONFIG_SPD_EEPROM
 199 #define CONFIG_SYS_SDRAM_SIZE   256
 200 #endif
 201
 202 #undef CONFIG_CLOCKS_IN_MHZ
 203
 204 #define CONFIG_SYS_INIT_RAM_LOCK        1
 205 #ifndef CONFIG_SYS_INIT_RAM_LOCK
 206 #define CONFIG_SYS_INIT_RAM_ADDR        0xe4010000      /* Initial RAM address */
 207 #else
 208 #define CONFIG_SYS_INIT_RAM_ADDR        0xe4000000      /* Initial RAM address */
 209 #endif
 210 #define CONFIG_SYS_INIT_RAM_END 0x4000          /* End of used area in RAM */
 211
 212 #define CONFIG_SYS_GBL_DATA_SIZE        128             /* num bytes initial data */
 213 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 214 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 215
 216 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 KB for Mon */
 217 #define CONFIG_SYS_MALLOC_LEN           (6 * 1024 * 1024)       /* Reserved for malloc */
 218
 219 /* Serial Port */
 220 #define CONFIG_CONS_INDEX       1
 221 #undef  CONFIG_SERIAL_SOFTWARE_FIFO
 222 #define CONFIG_SYS_NS16550
 223 #define CONFIG_SYS_NS16550_SERIAL
 224 #define CONFIG_SYS_NS16550_REG_SIZE     1
 225 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 226
 227 #define CONFIG_SYS_BAUDRATE_TABLE \
 228         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
 229
 230 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 231 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 232
 233 /* Use the HUSH parser */
 234 #define CONFIG_SYS_HUSH_PARSER
 235 #ifdef  CONFIG_SYS_HUSH_PARSER
 236 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 237 #endif
 238
 239 /*
 240  * Pass open firmware flat tree to kernel
 241  */
 242 #define CONFIG_OF_LIBFDT                1
 243 #define CONFIG_OF_BOARD_SETUP           1
 244 #define CONFIG_OF_STDOUT_VIA_ALIAS      1
 245
 246
 247 /* maximum size of the flat tree (8K) */
 248 #define OF_FLAT_TREE_MAX_SIZE   8192
 249
 250 /*
 251  * I2C
 252  */
 253 #define CONFIG_FSL_I2C          /* Use FSL common I2C driver */
 254 #define CONFIG_HARD_I2C         /* I2C with hardware support*/
 255 #undef  CONFIG_SOFT_I2C                 /* I2C bit-banged */
 256 #define CONFIG_SYS_I2C_SPEED            400000  /* I2C speed and slave address */
 257 #define CONFIG_SYS_I2C_SLAVE            0x7F
 258 #define CONFIG_SYS_I2C_NOPROBES {0x69}  /* Don't probe these addrs */
 259 #define CONFIG_SYS_I2C_OFFSET           0x3000
 260
 261 /*
 262  * General PCI
 263  * Addresses are mapped 1-1.
 264  */
 265 #define CONFIG_SYS_PCI1_MEM_BUS         0x80000000
 266 #define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BUS
 267 #define CONFIG_SYS_PCI1_MEM_VIRT        CONFIG_SYS_PCI1_MEM_BUS
 268 #define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000      /* 256M */
 269 #define CONFIG_SYS_PCI1_IO_BUS  0x0000000
 270 #define CONFIG_SYS_PCI1_IO_PHYS 0xe1000000
 271 #define CONFIG_SYS_PCI1_IO_VIRT 0xe1000000
 272 #define CONFIG_SYS_PCI1_IO_SIZE 0x00100000      /* 1M */
 273
 274 /* controller 1, Base address 0xa000 */
 275 #define CONFIG_SYS_PCIE1_MEM_BUS        0xa0000000
 276 #define CONFIG_SYS_PCIE1_MEM_PHYS       CONFIG_SYS_PCIE1_MEM_BUS
 277 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x10000000      /* 256M */
 278 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 279 #define CONFIG_SYS_PCIE1_IO_PHYS        0xe3000000
 280 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00100000      /* 1M */
 281
 282 /* controller 2, Base Address 0x9000 */
 283 #define CONFIG_SYS_PCIE2_MEM_BUS        0x90000000
 284 #define CONFIG_SYS_PCIE2_MEM_PHYS       CONFIG_SYS_PCIE2_MEM_BUS
 285 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x10000000      /* 256M */
 286 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000      /* reuse mem LAW */
 287 #define CONFIG_SYS_PCIE2_IO_PHYS        0xe2000000
 288 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00100000      /* 1M */
 289
 290
 291 #if defined(CONFIG_PCI)
 292
 293 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 294
 295 #define CONFIG_NET_MULTI
 296 #define CONFIG_CMD_NET
 297 #define CONFIG_PCI_PNP          /* do pci plug-and-play */
 298 #define CONFIG_CMD_REGINFO
 299
 300 #define CONFIG_ULI526X
 301 #ifdef CONFIG_ULI526X
 302 #define CONFIG_ETHADDR   00:E0:0C:00:00:01
 303 #endif
 304
 305 /************************************************************
 306  * USB support
 307  ************************************************************/
 308 #define CONFIG_PCI_OHCI         1
 309 #define CONFIG_USB_OHCI_NEW             1
 310 #define CONFIG_USB_KEYBOARD     1
 311 #define CONFIG_SYS_STDIO_DEREGISTER
 312 #define CONFIG_SYS_USB_EVENT_POLL       1
 313 #define CONFIG_SYS_USB_OHCI_SLOT_NAME   "ohci_pci"
 314 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
 315 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
 316
 317 #if !defined(CONFIG_PCI_PNP)
 318 #define PCI_ENET0_IOADDR        0xe0000000
 319 #define PCI_ENET0_MEMADDR       0xe0000000
 320 #define PCI_IDSEL_NUMBER        0x0c    /* slot0->3(IDSEL)=12->15 */
 321 #endif
 322
 323 #define CONFIG_DOS_PARTITION
 324 #define CONFIG_SCSI_AHCI
 325
 326 #ifdef CONFIG_SCSI_AHCI
 327 #define CONFIG_SATA_ULI5288
 328 #define CONFIG_SYS_SCSI_MAX_SCSI_ID     4
 329 #define CONFIG_SYS_SCSI_MAX_LUN 1
 330 #define CONFIG_SYS_SCSI_MAX_DEVICE      (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
 331 #define CONFIG_SYS_SCSI_MAXDEVICE       CONFIG_SYS_SCSI_MAX_DEVICE
 332 #endif
 333
 334 #endif  /* CONFIG_PCI */
 335
 336 /*
 337  * BAT0         2G      Cacheable, non-guarded
 338  * 0x0000_0000  2G      DDR
 339  */
 340 #define CONFIG_SYS_DBAT0L       (BATL_PP_RW)
 341 #define CONFIG_SYS_IBAT0L       (BATL_PP_RW)
 342
 343 /*
 344  * BAT1         1G      Cache-inhibited, guarded
 345  * 0x8000_0000  256M    PCI-1 Memory
 346  * 0xa000_0000  256M    PCI-Express 1 Memory
 347  * 0x9000_0000  256M    PCI-Express 2 Memory
 348  */
 349
 350 #define CONFIG_SYS_DBAT1L       (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
 351                         | BATL_GUARDEDSTORAGE)
 352 #define CONFIG_SYS_DBAT1U       (CONFIG_SYS_PCI1_MEM_VIRT | BATU_BL_1G | BATU_VS | BATU_VP)
 353 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
 354 #define CONFIG_SYS_IBAT1U       CONFIG_SYS_DBAT1U
 355
 356 /*
 357  * BAT2         16M     Cache-inhibited, guarded
 358  * 0xe100_0000  1M      PCI-1 I/O
 359  */
 360
 361 #define CONFIG_SYS_DBAT2L       (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
 362                         | BATL_GUARDEDSTORAGE)
 363 #define CONFIG_SYS_DBAT2U       (CONFIG_SYS_PCI1_IO_VIRT | BATU_BL_16M | BATU_VS | BATU_VP)
 364 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
 365 #define CONFIG_SYS_IBAT2U       CONFIG_SYS_DBAT2U
 366
 367 /*
 368  * BAT3         4M      Cache-inhibited, guarded
 369  * 0xe000_0000  4M      CCSR
 370  */
 371
 372 #define CONFIG_SYS_DBAT3L       (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
 373                         | BATL_GUARDEDSTORAGE)
 374 #define CONFIG_SYS_DBAT3U       (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
 375 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
 376 #define CONFIG_SYS_IBAT3U       CONFIG_SYS_DBAT3U
 377
 378 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR)
 379 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
 380                                        | BATL_PP_RW | BATL_CACHEINHIBIT \
 381                                        | BATL_GUARDEDSTORAGE)
 382 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \
 383                                        | BATU_BL_1M | BATU_VS | BATU_VP)
 384 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \
 385                                        | BATL_PP_RW | BATL_CACHEINHIBIT)
 386 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU
 387 #endif
 388
 389 /*
 390  * BAT4         32M     Cache-inhibited, guarded
 391  * 0xe200_0000  1M      PCI-Express 2 I/O
 392  * 0xe300_0000  1M      PCI-Express 1 I/O
 393  */
 394
 395 #define CONFIG_SYS_DBAT4L       (CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
 396                         | BATL_GUARDEDSTORAGE)
 397 #define CONFIG_SYS_DBAT4U       (CONFIG_SYS_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
 398 #define CONFIG_SYS_IBAT4L       (CONFIG_SYS_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
 399 #define CONFIG_SYS_IBAT4U       CONFIG_SYS_DBAT4U
 400
 401
 402 /*
 403  * BAT5         128K    Cacheable, non-guarded
 404  * 0xe400_0000  128K    Init RAM for stack in the CPU DCache (no backing memory)
 405  */
 406 #define CONFIG_SYS_DBAT5L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
 407 #define CONFIG_SYS_DBAT5U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
 408 #define CONFIG_SYS_IBAT5L       CONFIG_SYS_DBAT5L
 409 #define CONFIG_SYS_IBAT5U       CONFIG_SYS_DBAT5U
 410
 411 /*
 412  * BAT6         256M    Cache-inhibited, guarded
 413  * 0xf000_0000  256M    FLASH
 414  */
 415 #define CONFIG_SYS_DBAT6L       (CONFIG_SYS_FLASH_BASE   | BATL_PP_RW | BATL_CACHEINHIBIT \
 416                         | BATL_GUARDEDSTORAGE)
 417 #define CONFIG_SYS_DBAT6U       (CONFIG_SYS_FLASH_BASE   | BATU_BL_256M | BATU_VS | BATU_VP)
 418 #define CONFIG_SYS_IBAT6L       (CONFIG_SYS_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
 419 #define CONFIG_SYS_IBAT6U       CONFIG_SYS_DBAT6U
 420
 421 /* Map the last 1M of flash where we're running from reset */
 422 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
 423                                  | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 424 #define CONFIG_SYS_DBAT6U_EARLY (TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
 425 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \
 426                                  | BATL_MEMCOHERENCE)
 427 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY
 428
 429 /*
 430  * BAT7         4M      Cache-inhibited, guarded
 431  * 0xe800_0000  4M      PIXIS
 432  */
 433 #define CONFIG_SYS_DBAT7L       (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
 434                         | BATL_GUARDEDSTORAGE)
 435 #define CONFIG_SYS_DBAT7U       (PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
 436 #define CONFIG_SYS_IBAT7L       (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
 437 #define CONFIG_SYS_IBAT7U       CONFIG_SYS_DBAT7U
 438
 439
 440 /*
 441  * Environment
 442  */
 443 #ifndef CONFIG_SYS_RAMBOOT
 444 #define CONFIG_ENV_IS_IN_FLASH  1
 445 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 446 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 126k (one sector) for env */
 447 #define CONFIG_ENV_SIZE         0x2000
 448 #else
 449 #define CONFIG_ENV_IS_NOWHERE   1       /* Store ENV in memory only */
 450 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 451 #define CONFIG_ENV_SIZE         0x2000
 452 #endif
 453
 454 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 455 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 456
 457
 458 /*
 459  * BOOTP options
 460  */
 461 #define CONFIG_BOOTP_BOOTFILESIZE
 462 #define CONFIG_BOOTP_BOOTPATH
 463 #define CONFIG_BOOTP_GATEWAY
 464 #define CONFIG_BOOTP_HOSTNAME
 465
 466
 467 /*
 468  * Command line configuration.
 469  */
 470 #include <config_cmd_default.h>
 471
 472 #define CONFIG_CMD_PING
 473 #define CONFIG_CMD_I2C
 474 #define CONFIG_CMD_MII
 475
 476 #if defined(CONFIG_SYS_RAMBOOT)
 477 #undef CONFIG_CMD_SAVEENV
 478 #endif
 479
 480 #if defined(CONFIG_PCI)
 481 #define CONFIG_CMD_PCI
 482 #define CONFIG_CMD_SCSI
 483 #define CONFIG_CMD_EXT2
 484 #define CONFIG_CMD_USB
 485 #endif
 486
 487
 488 #define CONFIG_WATCHDOG                 /* watchdog enabled */
 489 #define CONFIG_SYS_WATCHDOG_FREQ        5000    /* Feed interval, 5s */
 490
 491 /*DIU Configuration*/
 492 #define DIU_CONNECT_TO_DVI              /* DIU controller connects to DVI encoder*/
 493
 494 /*
 495  * Miscellaneous configurable options
 496  */
 497 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 498 #define CONFIG_CMDLINE_EDITING          /* Command-line editing */
 499 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 500 #define CONFIG_SYS_PROMPT       "=> "           /* Monitor Command Prompt */
 501
 502 #if defined(CONFIG_CMD_KGDB)
 503 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 504 #else
 505 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
 506 #endif
 507
 508 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 509 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 510 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 511 #define CONFIG_SYS_HZ           1000            /* decrementer freq: 1ms ticks */
 512
 513 /*
 514  * For booting Linux, the board info and command line data
 515  * have to be in the first 8 MB of memory, since this is
 516  * the maximum mapped by the Linux kernel during initialization.
 517  */
 518 #define CONFIG_SYS_BOOTMAPSZ    (8 << 20)       /* Initial Memory map for Linux*/
 519
 520 /*
 521  * Internal Definitions
 522  *
 523  * Boot Flags
 524  */
 525 #define BOOTFLAG_COLD   0x01            /* Normal Power-On: Boot from FLASH */
 526 #define BOOTFLAG_WARM   0x02            /* Software reboot */
 527
 528 #if defined(CONFIG_CMD_KGDB)
 529 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 530 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 531 #endif
 532
 533 /*
 534  * Environment Configuration
 535  */
 536 #define CONFIG_IPADDR           192.168.1.100
 537
 538 #define CONFIG_HOSTNAME         unknown
 539 #define CONFIG_ROOTPATH         /opt/nfsroot
 540 #define CONFIG_BOOTFILE         uImage
 541 #define CONFIG_UBOOTPATH        8610hpcd/u-boot.bin
 542
 543 #define CONFIG_SERVERIP         192.168.1.1
 544 #define CONFIG_GATEWAYIP        192.168.1.1
 545 #define CONFIG_NETMASK          255.255.255.0
 546
 547 /* default location for tftp and bootm */
 548 #define CONFIG_LOADADDR         1000000
 549
 550 #define CONFIG_BOOTDELAY 10     /* -1 disables auto-boot */
 551 #undef  CONFIG_BOOTARGS         /* the boot command will set bootargs */
 552
 553 #define CONFIG_BAUDRATE 115200
 554
 555 #if defined(CONFIG_PCI1)
 556 #define PCI_ENV \
 557  "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
 558         "echo e;md ${a}e00 9\0" \
 559  "pci1regs=setenv a e0008; run pcireg\0" \
 560  "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
 561         "pci d.w $b.0 56 1\0" \
 562  "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \
 563         "pci w.w $b.0 56 ffff\0"        \
 564  "pci1err=setenv a e0008; run pcierr\0" \
 565  "pci1errc=setenv a e0008; run pcierrc\0"
 566 #else
 567 #define PCI_ENV ""
 568 #endif
 569
 570 #if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2)
 571 #define PCIE_ENV \
 572  "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
 573         "echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
 574  "pcie1regs=setenv a e000a; run pciereg\0"      \
 575  "pcie2regs=setenv a e0009; run pciereg\0"      \
 576  "pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\
 577         "pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;"        \
 578         "pci d $b.0 130 1\0" \
 579  "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\
 580         "pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \
 581         "pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0"            \
 582  "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0"       \
 583  "pcie1err=setenv a e000a; run pcieerr\0"       \
 584  "pcie2err=setenv a e0009; run pcieerr\0"       \
 585  "pcie1errc=setenv a e000a; run pcieerrc\0"     \
 586  "pcie2errc=setenv a e0009; run pcieerrc\0"
 587 #else
 588 #define PCIE_ENV ""
 589 #endif
 590
 591 #define DMA_ENV \
 592  "dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\
 593         "mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \
 594  "dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\
 595         "mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \
 596  "dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\
 597         "mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \
 598  "dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\
 599         "mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0"
 600
 601 #ifdef ENV_DEBUG
 602 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 603  "netdev=eth0\0"                                                \
 604  "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"                         \
 605  "tftpflash=tftpboot $loadaddr $uboot; "                        \
 606         "protect off " MK_STR(TEXT_BASE) " +$filesize; "        \
 607         "erase " MK_STR(TEXT_BASE) " +$filesize; "              \
 608         "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "      \
 609         "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
 610         "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"     \
 611  "consoledev=ttyS0\0"                                           \
 612  "ramdiskaddr=2000000\0"                                        \
 613  "ramdiskfile=8610hpcd/ramdisk.uboot\0"                         \
 614  "fdtaddr=c00000\0"                                             \
 615  "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0"                          \
 616  "bdev=sda3\0"                                  \
 617  "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
 618  "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
 619  "maxcpus=1"    \
 620  "eoi=mw e00400b0 0\0"                                          \
 621  "iack=md e00400a0 1\0"                                         \
 622  "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \
 623         "md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \
 624         "md ${a}f00 5\0" \
 625  "ddr1regs=setenv a e0002; run ddrreg\0" \
 626  "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \
 627         "md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \
 628         "md ${a}e60 1; md ${a}ef0 1d\0" \
 629  "guregs=setenv a e00e0; run gureg\0" \
 630  "mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \
 631  "mcmregs=setenv a e0001; run mcmreg\0" \
 632  "diuregs=md e002c000 1d\0" \
 633  "dium=mw e002c01c\0" \
 634  "diuerr=md e002c014 1\0" \
 635  "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 debug\0" \
 636  "monitor=0-DVI\0" \
 637  "pmregs=md e00e1000 2b\0" \
 638  "lawregs=md e0000c08 4b\0" \
 639  "lbcregs=md e0005000 36\0" \
 640  "dma0regs=md e0021100 12\0" \
 641  "dma1regs=md e0021180 12\0" \
 642  "dma2regs=md e0021200 12\0" \
 643  "dma3regs=md e0021280 12\0" \
 644  PCI_ENV \
 645  PCIE_ENV \
 646  DMA_ENV
 647 #else
 648 #define CONFIG_EXTRA_ENV_SETTINGS                               \
 649  "netdev=eth0\0"                                                \
 650  "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"                         \
 651  "consoledev=ttyS0\0"                                           \
 652  "ramdiskaddr=2000000\0"                                        \
 653  "ramdiskfile=8610hpcd/ramdisk.uboot\0"                         \
 654  "fdtaddr=c00000\0"                                             \
 655  "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0"                          \
 656  "bdev=sda3\0"                                                  \
 657  "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0\0"\
 658  "monitor=0-DVI\0"
 659 #endif
 660
 661 #define CONFIG_NFSBOOTCOMMAND                                   \
 662  "setenv bootargs root=/dev/nfs rw "                            \
 663         "nfsroot=$serverip:$rootpath "                          \
 664         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 665         "console=$consoledev,$baudrate $othbootargs;"           \
 666  "tftp $loadaddr $bootfile;"                                    \
 667  "tftp $fdtaddr $fdtfile;"                                      \
 668  "bootm $loadaddr - $fdtaddr"
 669
 670 #define CONFIG_RAMBOOTCOMMAND \
 671  "setenv bootargs root=/dev/ram rw "                            \
 672         "console=$consoledev,$baudrate $othbootargs;"           \
 673  "tftp $ramdiskaddr $ramdiskfile;"                              \
 674  "tftp $loadaddr $bootfile;"                                    \
 675  "tftp $fdtaddr $fdtfile;"                                      \
 676  "bootm $loadaddr $ramdiskaddr $fdtaddr"
 677
 678 #define CONFIG_BOOTCOMMAND              \
 679  "setenv bootargs root=/dev/$bdev rw "  \
 680         "console=$consoledev,$baudrate $othbootargs;"   \
 681  "tftp $loadaddr $bootfile;"            \
 682  "tftp $fdtaddr $fdtfile;"              \
 683  "bootm $loadaddr - $fdtaddr"
 684
 685 #endif  /* __CONFIG_H */