arm: omap3: Add uart4 omap3 adddress

[people/ms/u-boot.git] / include / configs / MVBLM7.h

/*
 * Copyright (C) Matrix Vision GmbH 2008
 *
 * Matrix Vision mvBlueLYNX-M7 configuration file
 * based on Freescale's MPC8349ITX.
 *
 * SPDX-License-Identifier:     GPL-2.0+
 */


#ifndef __CONFIG_H
#define __CONFIG_H

#include <version.h>

/*
 * High Level Configuration Options
 */
#define CONFIG_E300     1
#define CONFIG_MPC83xx  1
#define CONFIG_MPC834x  1
#define CONFIG_MPC8343  1

#define CONFIG_SYS_TEXT_BASE    0xFFF00000

#define CONFIG_SYS_IMMR         0xE0000000

#define CONFIG_PCI
#define CONFIG_PCI_INDIRECT_BRIDGE
#define CONFIG_PCI_SKIP_HOST_BRIDGE
#define CONFIG_TSEC_ENET
#define CONFIG_MPC8XXX_SPI
#define CONFIG_HARD_SPI
#define MVBLM7_MMC_CS   0x04000000
#define CONFIG_MISC_INIT_R

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED        100000
#define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET       0x3000
#define CONFIG_SYS_FSL_I2C2_SPEED       100000
#define CONFIG_SYS_FSL_I2C2_SLAVE       0x7F
#define CONFIG_SYS_FSL_I2C2_OFFSET      0x3100

/*
 * DDR Setup
 */
#undef  CONFIG_SPD_EEPROM

#define CONFIG_SYS_DDR_BASE             0x00000000
#define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
#define CONFIG_SYS_83XX_DDR_USES_CS0    1
#define CONFIG_SYS_MEMTEST_START        (60<<20)
#define CONFIG_SYS_MEMTEST_END          (70<<20)
#define CONFIG_VERY_BIG_RAM

#define CONFIG_SYS_DDRCDR               (DDRCDR_PZ_HIZ \
                                        | DDRCDR_NZ_HIZ \
                                        | DDRCDR_Q_DRN)
                                        /* 0x22000001 */
#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05

#define CONFIG_SYS_DDR_SIZE             512

#define CONFIG_SYS_DDR_CS0_CONFIG       0x80014202

#define CONFIG_SYS_DDR_CS0_BNDS         0x0000003f

#define CONFIG_SYS_DDR_TIMING_0         0x00260802
#define CONFIG_SYS_DDR_TIMING_1         0x3837c322
#define CONFIG_SYS_DDR_TIMING_2         0x0f9848c6
#define CONFIG_SYS_DDR_TIMING_3         0x00000000

#define CONFIG_SYS_DDR_SDRAM_CFG        0x43080008
#define CONFIG_SYS_DDR_SDRAM_CFG2       0x00401000
#define CONFIG_SYS_DDR_INTERVAL         0x02000100

#define CONFIG_SYS_DDR_MODE             0x04040242
#define CONFIG_SYS_DDR_MODE2            0x00800000

/* Flash */
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_16BIT

#define CONFIG_SYS_FLASH_BASE           0xFF800000
#define CONFIG_SYS_FLASH_SIZE           8
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_ERASE_TOUT     60000
#define CONFIG_SYS_FLASH_WRITE_TOUT     500
#define CONFIG_SYS_MAX_FLASH_BANKS      1
#define CONFIG_SYS_MAX_FLASH_SECT       256

#define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE \
                                | BR_PS_16 \
                                | BR_MS_GPCM \
                                | BR_V)
#define CONFIG_SYS_OR0_PRELIM   (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \
                                | OR_UPM_XAM \
                                | OR_GPCM_CSNT \
                                | OR_GPCM_ACS_DIV2 \
                                | OR_GPCM_XACS \
                                | OR_GPCM_SCY_15 \
                                | OR_GPCM_TRLX_SET \
                                | OR_GPCM_EHTR_SET \
                                | OR_GPCM_EAD)
#define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_LBLAWAR0_PRELIM      (LBLAWAR_EN | LBLAWAR_8MB)

/*
 * U-Boot memory configuration
 */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#undef  CONFIG_SYS_RAMBOOT

#define CONFIG_SYS_INIT_RAM_LOCK
#define CONFIG_SYS_INIT_RAM_ADDR        0xFD000000 /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM*/

#define CONFIG_SYS_GBL_DATA_OFFSET      \
                        (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET

/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
#define CONFIG_SYS_MONITOR_LEN          (512 * 1024)
#define CONFIG_SYS_MALLOC_LEN           (512 * 1024)

/*
 * Local Bus LCRR and LBCR regs
 *  LCRR:  DLL bypass, Clock divider is 4
 * External Local Bus rate is
 *  CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
 */
#define CONFIG_SYS_LCRR_DBYP    LCRR_DBYP
#define CONFIG_SYS_LCRR_CLKDIV  LCRR_CLKDIV_4
#define CONFIG_SYS_LBC_LBCR     0x00000000

/* LB sdram refresh timer, about 6us */
#define CONFIG_SYS_LBC_LSRT     0x32000000
/* LB refresh timer prescal, 266MHz/32*/
#define CONFIG_SYS_LBC_MRTPR    0x20000000

/*
 * Serial Port
 */
#define CONFIG_CONS_INDEX       1
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)

#define CONFIG_SYS_BAUDRATE_TABLE  \
                {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

#define CONFIG_CONSOLE          ttyS0
#define CONFIG_BAUDRATE         115200

#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR + 0x4500)
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR + 0x4600)

/* pass open firmware flat tree */
#define CONFIG_OF_LIBFDT                1
#define CONFIG_OF_BOARD_SETUP           1
#define CONFIG_OF_STDOUT_VIA_ALIAS      1
#define MV_DTB_NAME     "mvblm7.dtb"

/*
 * PCI
 */
#define CONFIG_SYS_PCI1_MEM_BASE        0x80000000
#define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BASE
#define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000
#define CONFIG_SYS_PCI1_MMIO_BASE       \
                        (CONFIG_SYS_PCI1_MEM_BASE + CONFIG_SYS_PCI1_MEM_SIZE)
#define CONFIG_SYS_PCI1_MMIO_PHYS       CONFIG_SYS_PCI1_MMIO_BASE
#define CONFIG_SYS_PCI1_MMIO_SIZE       0x10000000
#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
#define CONFIG_SYS_PCI1_IO_SIZE 0x01000000

#define CONFIG_NET_RETRY_COUNT  3

#define CONFIG_PCI_66M
#define CONFIG_83XX_CLKIN       66666667
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW

/* TSEC */
#define CONFIG_GMII
#define CONFIG_SYS_VSC8601_SKEWFIX
#define CONFIG_SYS_VSC8601_SKEW_TX      3
#define CONFIG_SYS_VSC8601_SKEW_RX      3

#define CONFIG_TSEC1
#define CONFIG_TSEC2

#define CONFIG_HAS_ETH0
#define CONFIG_TSEC1_NAME       "TSEC0"
#define CONFIG_FEC1_PHY_NORXERR
#define CONFIG_SYS_TSEC1_OFFSET 0x24000
#define CONFIG_SYS_TSEC1        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
#define TSEC1_PHY_ADDR          0x10
#define TSEC1_PHYIDX            0
#define TSEC1_FLAGS             (TSEC_GIGABIT|TSEC_REDUCED)

#define CONFIG_HAS_ETH1
#define CONFIG_TSEC2_NAME       "TSEC1"
#define CONFIG_FEC2_PHY_NORXERR
#define CONFIG_SYS_TSEC2_OFFSET 0x25000
#define CONFIG_SYS_TSEC2        (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
#define TSEC2_PHY_ADDR          0x11
#define TSEC2_PHYIDX            0
#define TSEC2_FLAGS             (TSEC_GIGABIT|TSEC_REDUCED)

#define CONFIG_ETHPRIME         "TSEC0"

#define CONFIG_BOOTP_VENDOREX
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_DNS
#define CONFIG_BOOTP_DNS2
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_NTPSERVER
#define CONFIG_BOOTP_RANDOM_DELAY
#define CONFIG_BOOTP_SEND_HOSTNAME

/* USB */
#define CONFIG_SYS_USB_HOST
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_FSL
#define CONFIG_HAS_FSL_DR_USB
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET

/*
 * Environment
 */
#undef  CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_ENV_OVERWRITE

#define CONFIG_ENV_IS_IN_FLASH  1
#define CONFIG_ENV_ADDR         0xFF800000
#define CONFIG_ENV_SIZE         0x2000
#define CONFIG_ENV_SECT_SIZE    0x2000
#define CONFIG_ENV_ADDR_REDUND  (CONFIG_ENV_ADDR+CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE

#define CONFIG_LOADS_ECHO
#define CONFIG_SYS_LOADS_BAUD_CHANGE

/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_CACHE
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_NET
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_PCI
#define CONFIG_CMD_I2C
#define CONFIG_CMD_FPGA
#define CONFIG_CMD_USB
#define CONFIG_DOS_PARTITION

#undef CONFIG_WATCHDOG

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING
#define CONFIG_AUTO_COMPLETE    /* add autocompletion support   */
#define CONFIG_SYS_HUSH_PARSER

/* default load address */
#define CONFIG_SYS_LOAD_ADDR    0x2000000
/* default location for tftp and bootm */
#define CONFIG_LOADADDR 0x200000

#define CONFIG_SYS_PROMPT       "mvBL-M7> "
#define CONFIG_SYS_CBSIZE       256

#define CONFIG_SYS_PBSIZE       \
                        (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS      16
#define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 256 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
                                /* Initial Memory map for Linux*/
#define CONFIG_SYS_BOOTMAPSZ    (256 << 20)

#define CONFIG_SYS_HRCW_LOW     0x0
#define CONFIG_SYS_HRCW_HIGH    0x0

/*
 * System performance
 */
#define CONFIG_SYS_ACR_PIPE_DEP 3       /* Arbiter pipeline depth (0-3) */
#define CONFIG_SYS_ACR_RPTCNT   3       /* Arbiter repeat count (0-7) */
#define CONFIG_SYS_SPCR_TSEC1EP 3       /* TSEC1 emergency priority (0-3) */
#define CONFIG_SYS_SPCR_TSEC2EP 3       /* TSEC2 emergency priority (0-3) */

/* clocking */
#define CONFIG_SYS_SCCR_ENCCM           0
#define CONFIG_SYS_SCCR_USBMPHCM        0
#define CONFIG_SYS_SCCR_USBDRCM 2
#define CONFIG_SYS_SCCR_TSEC1CM 1
#define CONFIG_SYS_SCCR_TSEC2CM 1

#define CONFIG_SYS_SICRH        0x1fef0003
#define CONFIG_SYS_SICRL        (SICRL_LDP_A | SICRL_USB1 | SICRL_USB0)

#define CONFIG_SYS_HID0_INIT    0x000000000
#define CONFIG_SYS_HID0_FINAL   (CONFIG_SYS_HID0_INIT | \
                                 HID0_ENABLE_INSTRUCTION_CACHE)

#define CONFIG_SYS_HID2 HID2_HBE
#define CONFIG_HIGH_BATS        1

/* DDR  */
#define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE \
                                | BATL_PP_RW \
                                | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE \
                                | BATU_BL_256M \
                                | BATU_VS \
                                | BATU_VP)

/* PCI  */
#define CONFIG_SYS_IBAT1L       (CONFIG_SYS_PCI1_MEM_BASE \
                                | BATL_PP_RW \
                                | BATL_MEMCOHERENCE)
#define CONFIG_SYS_IBAT1U       (CONFIG_SYS_PCI1_MEM_BASE \
                                | BATU_BL_256M \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_IBAT2L       (CONFIG_SYS_PCI1_MMIO_BASE \
                                | BATL_PP_RW \
                                | BATL_CACHEINHIBIT \
                                | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT2U       (CONFIG_SYS_PCI1_MMIO_BASE \
                                | BATU_BL_256M \
                                | BATU_VS \
                                | BATU_VP)

/* no PCI2 */
#define CONFIG_SYS_IBAT3L       0
#define CONFIG_SYS_IBAT3U       0
#define CONFIG_SYS_IBAT4L       0
#define CONFIG_SYS_IBAT4U       0

/* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
#define CONFIG_SYS_IBAT5L       (CONFIG_SYS_IMMR \
                                | BATL_PP_RW \
                                | BATL_CACHEINHIBIT \
                                | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT5U       (CONFIG_SYS_IMMR \
                                | BATU_BL_256M \
                                | BATU_VS \
                                | BATU_VP)

/* stack in DCACHE 0xFDF00000 & FLASH @ 0xFF800000 */
#define CONFIG_SYS_IBAT6L       (0xF0000000 \
                                | BATL_PP_RW \
                                | BATL_MEMCOHERENCE \
                                | BATL_GUARDEDSTORAGE)
#define CONFIG_SYS_IBAT6U       (0xF0000000 \
                                | BATU_BL_256M \
                                | BATU_VS \
                                | BATU_VP)
#define CONFIG_SYS_IBAT7L       0
#define CONFIG_SYS_IBAT7U       0

#define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
#define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
#define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
#define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
#define CONFIG_SYS_DBAT2L       CONFIG_SYS_IBAT2L
#define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
#define CONFIG_SYS_DBAT3L       CONFIG_SYS_IBAT3L
#define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
#define CONFIG_SYS_DBAT4L       CONFIG_SYS_IBAT4L
#define CONFIG_SYS_DBAT4U       CONFIG_SYS_IBAT4U
#define CONFIG_SYS_DBAT5L       CONFIG_SYS_IBAT5L
#define CONFIG_SYS_DBAT5U       CONFIG_SYS_IBAT5U
#define CONFIG_SYS_DBAT6L       CONFIG_SYS_IBAT6L
#define CONFIG_SYS_DBAT6U       CONFIG_SYS_IBAT6U
#define CONFIG_SYS_DBAT7L       CONFIG_SYS_IBAT7L
#define CONFIG_SYS_DBAT7U       CONFIG_SYS_IBAT7U

/*
 * Environment Configuration
 */
#define CONFIG_ENV_OVERWRITE

#define CONFIG_NETDEV           eth0

/* Default path and filenames */
#define CONFIG_BOOTDELAY                5
#define CONFIG_AUTOBOOT_KEYED
#define CONFIG_AUTOBOOT_STOP_STR        "s"
#define CONFIG_ZERO_BOOTDELAY_CHECK
#define CONFIG_RESET_TO_RETRY           1000

#define MV_CI                   "mvBL-M7"
#define MV_VCI                  "mvBL-M7"
#define MV_FPGA_DATA            0xfff40000
#define MV_FPGA_SIZE            0
#define MV_KERNEL_ADDR          0xff810000
#define MV_INITRD_ADDR          0xffb00000
#define MV_SCRIPT_ADDR          0xff804000
#define MV_SCRIPT_ADDR2         0xff806000
#define MV_DTB_ADDR             0xff808000
#define MV_INITRD_LENGTH        0x00400000

#define CONFIG_SHOW_BOOT_PROGRESS 1

#define MV_KERNEL_ADDR_RAM      0x00100000
#define MV_DTB_ADDR_RAM         0x00600000
#define MV_INITRD_ADDR_RAM      0x01000000

#define CONFIG_BOOTCOMMAND      "if imi ${script_addr}; "               \
                                        "then source ${script_addr}; "  \
                                        "else source ${script_addr2}; " \
                                "fi;"
#define CONFIG_BOOTARGS         "root=/dev/ram ro rootfstype=squashfs"

#define CONFIG_EXTRA_ENV_SETTINGS                               \
        "console_nr=0\0"                                        \
        "baudrate=" __stringify(CONFIG_BAUDRATE) "\0"           \
        "stdin=serial\0"                                        \
        "stdout=serial\0"                                       \
        "stderr=serial\0"                                       \
        "fpga=0\0"                                              \
        "fpgadata=" __stringify(MV_FPGA_DATA) "\0"                      \
        "fpgadatasize=" __stringify(MV_FPGA_SIZE) "\0"          \
        "script_addr=" __stringify(MV_SCRIPT_ADDR) "\0"         \
        "script_addr2=" __stringify(MV_SCRIPT_ADDR2) "\0"               \
        "mv_kernel_addr=" __stringify(MV_KERNEL_ADDR) "\0"              \
        "mv_kernel_addr_ram=" __stringify(MV_KERNEL_ADDR_RAM) "\0"      \
        "mv_initrd_addr=" __stringify(MV_INITRD_ADDR) "\0"              \
        "mv_initrd_addr_ram=" __stringify(MV_INITRD_ADDR_RAM) "\0"      \
        "mv_initrd_length=" __stringify(MV_INITRD_LENGTH) "\0"  \
        "mv_dtb_addr=" __stringify(MV_DTB_ADDR) "\0"                    \
        "mv_dtb_addr_ram=" __stringify(MV_DTB_ADDR_RAM) "\0"            \
        "dtb_name=" __stringify(MV_DTB_NAME) "\0"                       \
        "mv_version=" U_BOOT_VERSION "\0"                       \
        "dhcp_client_id=" MV_CI "\0"                            \
        "dhcp_vendor-class-identifier=" MV_VCI "\0"             \
        "netretry=no\0"                                         \
        "use_static_ipaddr=no\0"                                \
        "static_ipaddr=192.168.90.10\0"                         \
        "static_netmask=255.255.255.0\0"                        \
        "static_gateway=0.0.0.0\0"                              \
        "initrd_name=uInitrd.mvBL-M7-rfs\0"                     \
        "zcip=no\0"                                             \
        "netboot=yes\0"                                         \
        "mvtest=Ff\0"                                           \
        "tried_bootfromflash=no\0"                              \
        "tried_bootfromnet=no\0"                                \
        "bootfile=mvblm72625.boot\0"                            \
        "use_dhcp=yes\0"                                        \
        "gev_start=yes\0"                                       \
        "mvbcdma_debug=0\0"                                     \
        "mvbcia_debug=0\0"                                      \
        "propdev_debug=0\0"                                     \
        "gevss_debug=0\0"                                       \
        "watchdog=0\0"                                          \
        "usb_dr_mode=host\0"                                    \
        "sensor_cnt=2\0"                                        \
        ""

#define CONFIG_FPGA_COUNT       1
#define CONFIG_FPGA
#define CONFIG_FPGA_ALTERA
#define CONFIG_FPGA_CYCLON2

#endif