include/configs/P1022DS.h

   1 /*
   2  * Copyright 2010 Freescale Semiconductor, Inc.
   3  * Authors: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
   4  *          Timur Tabi <timur@freescale.com>
   5  *
   6  * This program is free software; you can redistribute it and/or modify it
   7  * under the terms of the GNU General Public License as published by the Free
   8  * Software Foundation; either version 2 of the License, or (at your option)
   9  * any later version.
  10  */
  11
  12 #ifndef __CONFIG_H
  13 #define __CONFIG_H
  14
  15 #include "../board/freescale/common/ics307_clk.h"
  16
  17 /* High Level Configuration Options */
  18 #define CONFIG_BOOKE                    /* BOOKE */
  19 #define CONFIG_E500                     /* BOOKE e500 family */
  20 #define CONFIG_MPC85xx                  /* MPC8540/60/55/41/48 */
  21 #define CONFIG_P1022
  22 #define CONFIG_P1022DS
  23 #define CONFIG_MP                       /* support multiple processors */
  24
  25 #define CONFIG_FSL_ELBC                 /* Has Enhanced localbus controller */
  26 #define CONFIG_PCI                      /* Enable PCI/PCIE */
  27 #define CONFIG_PCIE1                    /* PCIE controler 1 (slot 1) */
  28 #define CONFIG_PCIE2                    /* PCIE controler 2 (slot 2) */
  29 #define CONFIG_PCIE3                    /* PCIE controler 3 (ULI bridge) */
  30 #define CONFIG_FSL_PCI_INIT             /* Use common FSL init code */
  31 #define CONFIG_FSL_PCIE_RESET           /* need PCIe reset errata */
  32 #define CONFIG_SYS_PCI_64BIT            /* enable 64-bit PCI resources */
  33
  34 #define CONFIG_PHYS_64BIT
  35 #define CONFIG_ENABLE_36BIT_PHYS
  36 #define CONFIG_ADDR_MAP
  37 #define CONFIG_SYS_NUM_ADDR_MAP         16      /* number of TLB1 entries */
  38
  39 #define CONFIG_FSL_LAW                  /* Use common FSL init code */
  40
  41 #define CONFIG_SYS_CLK_FREQ     get_board_sys_clk()
  42 #define CONFIG_DDR_CLK_FREQ     get_board_ddr_clk()
  43 #define CONFIG_ICS307_REFCLK_HZ 33333000  /* ICS307 clock chip ref freq */
  44
  45 /*
  46  * These can be toggled for performance analysis, otherwise use default.
  47  */
  48 #define CONFIG_L2_CACHE
  49 #define CONFIG_BTB
  50
  51 #define CONFIG_SYS_MEMTEST_START        0x00000000
  52 #define CONFIG_SYS_MEMTEST_END          0x7fffffff
  53
  54 /*
  55  * Base addresses -- Note these are effective addresses where the
  56  * actual resources get mapped (not physical addresses)
  57  */
  58 #define CONFIG_SYS_CCSRBAR_DEFAULT      0xff700000      /* CCSRBAR Default */
  59 #define CONFIG_SYS_CCSRBAR              0xffe00000      /* relocated CCSRBAR */
  60 #define CONFIG_SYS_CCSRBAR_PHYS         0xfffe00000ull
  61 #define CONFIG_SYS_IMMR                 CONFIG_SYS_CCSRBAR
  62
  63 #define CONFIG_SYS_PCIE1_ADDR           (CONFIG_SYS_CCSRBAR + 0x9000) /* pci0 */
  64 #define CONFIG_SYS_PCIE2_ADDR           (CONFIG_SYS_CCSRBAR + 0xa000) /* pci1 */
  65 #define CONFIG_SYS_PCIE3_ADDR           (CONFIG_SYS_CCSRBAR + 0xb000) /* pci2 */
  66
  67 /* DDR Setup */
  68 #define CONFIG_DDR_SPD
  69 #define CONFIG_VERY_BIG_RAM
  70 #define CONFIG_FSL_DDR3
  71
  72 #ifdef CONFIG_DDR_ECC
  73 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  74 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  75 #endif
  76
  77 #define CONFIG_SYS_DDR_SDRAM_BASE       0x00000000
  78 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  79
  80 #define CONFIG_NUM_DDR_CONTROLLERS      1
  81 #define CONFIG_DIMM_SLOTS_PER_CTLR      1
  82 #define CONFIG_CHIP_SELECTS_PER_CTRL    (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
  83
  84 /* I2C addresses of SPD EEPROMs */
  85 #define CONFIG_SYS_SPD_BUS_NUM          1
  86 #define SPD_EEPROM_ADDRESS1             0x51    /* CTLR 0 DIMM 0 */
  87
  88 /*
  89  * Memory map
  90  *
  91  * 0x0000_0000  0x7fff_ffff     DDR                     2G Cacheable
  92  * 0x8000_0000  0xdfff_ffff     PCI Express Mem         1.5G non-cacheable
  93  * 0xffc0_0000  0xffc2_ffff     PCI IO range            192K non-cacheable
  94  *
  95  * Localbus cacheable (TBD)
  96  * 0xXXXX_XXXX  0xXXXX_XXXX     SRAM                    YZ M Cacheable
  97  *
  98  * Localbus non-cacheable
  99  * 0xe000_0000  0xe80f_ffff     Promjet/free            128M non-cacheable
 100  * 0xe800_0000  0xefff_ffff     FLASH                   128M non-cacheable
 101  * 0xffdf_0000  0xffdf_7fff     PIXIS                   32K non-cacheable TLB0
 102  * 0xffd0_0000  0xffd0_3fff     L1 for stack            16K Cacheable TLB0
 103  * 0xffe0_0000  0xffef_ffff     CCSR                    1M non-cacheable
 104  */
 105
 106 /*
 107  * Local Bus Definitions
 108  */
 109 #define CONFIG_SYS_FLASH_BASE           0xe0000000 /* start of FLASH 128M */
 110 #define CONFIG_SYS_FLASH_BASE_PHYS      0xfe0000000ull
 111
 112 #define CONFIG_FLASH_BR_PRELIM  \
 113         (BR_PHYS_ADDR((CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000)) | BR_PS_16 | BR_V)
 114 #define CONFIG_FLASH_OR_PRELIM  (OR_AM_128MB | 0xff7)
 115
 116 #define CONFIG_SYS_BR0_PRELIM   CONFIG_FLASH_BR_PRELIM  /* NOR Base Address */
 117 #define CONFIG_SYS_OR0_PRELIM   CONFIG_FLASH_OR_PRELIM  /* NOR Options */
 118
 119 #define CONFIG_SYS_BR1_PRELIM   \
 120         (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
 121 #define CONFIG_SYS_OR1_PRELIM   CONFIG_FLASH_OR_PRELIM
 122
 123 #define CONFIG_SYS_FLASH_BANKS_LIST     \
 124         {CONFIG_SYS_FLASH_BASE_PHYS + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
 125 #define CONFIG_SYS_FLASH_QUIET_TEST
 126 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 127
 128 #define CONFIG_SYS_MAX_FLASH_BANKS      2
 129 #define CONFIG_SYS_MAX_FLASH_SECT       1024
 130
 131 #define CONFIG_SYS_MONITOR_BASE         TEXT_BASE       /* start of monitor */
 132
 133 #define CONFIG_FLASH_CFI_DRIVER
 134 #define CONFIG_SYS_FLASH_CFI
 135 #define CONFIG_SYS_FLASH_EMPTY_INFO
 136
 137 #define CONFIG_BOARD_EARLY_INIT_F
 138 #define CONFIG_BOARD_EARLY_INIT_R
 139 #define CONFIG_MISC_INIT_R
 140
 141 #define CONFIG_FSL_NGPIXIS
 142 #define PIXIS_BASE              0xffdf0000      /* PIXIS registers */
 143 #define PIXIS_BASE_PHYS         0xfffdf0000ull
 144
 145 #define CONFIG_SYS_BR2_PRELIM   (BR_PHYS_ADDR(PIXIS_BASE_PHYS) | BR_PS_8 | BR_V)
 146 #define CONFIG_SYS_OR2_PRELIM   (OR_AM_32KB | 0x6ff7)
 147
 148 #define PIXIS_LBMAP_SWITCH      7
 149 #define PIXIS_LBMAP_MASK        0xE0
 150 #define PIXIS_LBMAP_ALTBANK     0x20
 151
 152 #define CONFIG_SYS_INIT_RAM_LOCK
 153 #define CONFIG_SYS_INIT_RAM_ADDR        0xffd00000 /* Initial L1 address */
 154 #define CONFIG_SYS_INIT_RAM_END         0x00004000 /* End of used area in RAM */
 155
 156 #define CONFIG_SYS_GBL_DATA_SIZE        128     /* num bytes initial data */
 157 #define CONFIG_SYS_GBL_DATA_OFFSET      \
 158         (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 159 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 160
 161 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)
 162 #define CONFIG_SYS_MALLOC_LEN           (6 * 1024 * 1024)
 163
 164 /*
 165  * Serial Port
 166  */
 167 #define CONFIG_CONS_INDEX               1
 168 #define CONFIG_SYS_NS16550
 169 #define CONFIG_SYS_NS16550_SERIAL
 170 #define CONFIG_SYS_NS16550_REG_SIZE     1
 171 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 172
 173 #define CONFIG_SYS_BAUDRATE_TABLE       \
 174         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 175
 176 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
 177 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
 178
 179 /* Use the HUSH parser */
 180 #define CONFIG_SYS_HUSH_PARSER
 181 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 182
 183 #define CONFIG_FSL_DIU_FB
 184 #define CONFIG_SYS_DIU_ADDR     (CONFIG_SYS_CCSRBAR + 0x10000)
 185
 186 /* Video */
 187 /* #define CONFIG_VIDEO */
 188 #ifdef CONFIG_VIDEO
 189 #define CONFIG_CFB_CONSOLE
 190 #define CONFIG_VGA_AS_SINGLE_DEVICE
 191 #endif
 192
 193 /*
 194  * Pass open firmware flat tree
 195  */
 196 #define CONFIG_OF_LIBFDT
 197 #define CONFIG_OF_BOARD_SETUP
 198 #define CONFIG_OF_STDOUT_VIA_ALIAS
 199
 200 /* new uImage format support */
 201 #define CONFIG_FIT
 202 #define CONFIG_FIT_VERBOSE
 203
 204 /* I2C */
 205 #define CONFIG_FSL_I2C
 206 #define CONFIG_HARD_I2C
 207 #define CONFIG_I2C_MULTI_BUS
 208 #define CONFIG_SYS_I2C_SPEED            400000
 209 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x57
 210 #define CONFIG_SYS_I2C_SLAVE            0x7F
 211 #define CONFIG_SYS_I2C_NOPROBES         {{0, 0x29}}
 212 #define CONFIG_SYS_I2C_OFFSET           0x3000
 213 #define CONFIG_SYS_I2C2_OFFSET          0x3100
 214
 215 /*
 216  * I2C2 EEPROM
 217  */
 218 #define CONFIG_ID_EEPROM
 219 #define CONFIG_SYS_I2C_EEPROM_NXID
 220 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x57
 221 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 222 #define CONFIG_SYS_EEPROM_BUS_NUM       1
 223
 224 /*
 225  * General PCI
 226  * Memory space is mapped 1-1, but I/O space must start from 0.
 227  */
 228
 229 /* controller 1, Slot 2, tgtid 1, Base address a000 */
 230 #define CONFIG_SYS_PCIE1_MEM_VIRT       0xc0000000
 231 #define CONFIG_SYS_PCIE1_MEM_BUS        0xe0000000
 232 #define CONFIG_SYS_PCIE1_MEM_PHYS       0xc40000000ull
 233 #define CONFIG_SYS_PCIE1_MEM_SIZE       0x20000000      /* 512M */
 234 #define CONFIG_SYS_PCIE1_IO_VIRT        0xffc20000
 235 #define CONFIG_SYS_PCIE1_IO_BUS         0x00000000
 236 #define CONFIG_SYS_PCIE1_IO_PHYS        0xfffc20000ull
 237 #define CONFIG_SYS_PCIE1_IO_SIZE        0x00010000      /* 64k */
 238
 239 /* controller 2, direct to uli, tgtid 2, Base address 9000 */
 240 #define CONFIG_SYS_PCIE2_MEM_VIRT       0xa0000000
 241 #define CONFIG_SYS_PCIE2_MEM_BUS        0xe0000000
 242 #define CONFIG_SYS_PCIE2_MEM_PHYS       0xc20000000ull
 243 #define CONFIG_SYS_PCIE2_MEM_SIZE       0x20000000      /* 512M */
 244 #define CONFIG_SYS_PCIE2_IO_VIRT        0xffc10000
 245 #define CONFIG_SYS_PCIE2_IO_BUS         0x00000000
 246 #define CONFIG_SYS_PCIE2_IO_PHYS        0xfffc10000ull
 247 #define CONFIG_SYS_PCIE2_IO_SIZE        0x00010000      /* 64k */
 248
 249 /* controller 3, Slot 1, tgtid 3, Base address b000 */
 250 #define CONFIG_SYS_PCIE3_MEM_VIRT       0x80000000
 251 #define CONFIG_SYS_PCIE3_MEM_BUS        0xe0000000
 252 #define CONFIG_SYS_PCIE3_MEM_PHYS       0xc00000000ull
 253 #define CONFIG_SYS_PCIE3_MEM_SIZE       0x20000000      /* 512M */
 254 #define CONFIG_SYS_PCIE3_IO_VIRT        0xffc00000
 255 #define CONFIG_SYS_PCIE3_IO_BUS         0x00000000
 256 #define CONFIG_SYS_PCIE3_IO_PHYS        0xfffc00000ull
 257 #define CONFIG_SYS_PCIE3_IO_SIZE        0x00010000      /* 64k */
 258
 259 #ifdef CONFIG_PCI
 260 #define CONFIG_NET_MULTI
 261 #define CONFIG_PCI_PNP                  /* do pci plug-and-play */
 262 #define CONFIG_PCI_SCAN_SHOW            /* show pci devices on startup */
 263 #endif
 264
 265 /* SATA */
 266 #define CONFIG_LIBATA
 267 #define CONFIG_FSL_SATA
 268
 269 #define CONFIG_SYS_SATA_MAX_DEVICE      2
 270 #define CONFIG_SATA1
 271 #define CONFIG_SYS_SATA1                CONFIG_SYS_MPC85xx_SATA1_ADDR
 272 #define CONFIG_SYS_SATA1_FLAGS          FLAGS_DMA
 273 #define CONFIG_SATA2
 274 #define CONFIG_SYS_SATA2                CONFIG_SYS_MPC85xx_SATA2_ADDR
 275 #define CONFIG_SYS_SATA2_FLAGS          FLAGS_DMA
 276
 277 #ifdef CONFIG_FSL_SATA
 278 #define CONFIG_LBA48
 279 #define CONFIG_CMD_SATA
 280 #define CONFIG_DOS_PARTITION
 281 #define CONFIG_CMD_EXT2
 282 #endif
 283
 284 #define CONFIG_MMC
 285 #ifdef CONFIG_MMC
 286 #define CONFIG_CMD_MMC
 287 #define CONFIG_FSL_ESDHC
 288 #define CONFIG_GENERIC_MMC
 289 #define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
 290 #endif
 291
 292 #if defined(CONFIG_MMC) || defined(CONFIG_USB_EHCI)
 293 #define CONFIG_CMD_EXT2
 294 #define CONFIG_CMD_FAT
 295 #define CONFIG_DOS_PARTITION
 296 #endif
 297
 298 #define CONFIG_TSEC_ENET
 299 #ifdef CONFIG_TSEC_ENET
 300
 301 #define CONFIG_TSECV2
 302 #define CONFIG_NET_MULTI
 303
 304 #define CONFIG_MII                      /* MII PHY management */
 305 #define CONFIG_TSEC1            1
 306 #define CONFIG_TSEC1_NAME       "eTSEC1"
 307 #define CONFIG_TSEC2            1
 308 #define CONFIG_TSEC2_NAME       "eTSEC2"
 309
 310 #define TSEC1_PHY_ADDR          1
 311 #define TSEC2_PHY_ADDR          2
 312
 313 #define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 314 #define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
 315
 316 #define TSEC1_PHYIDX            0
 317 #define TSEC2_PHYIDX            0
 318
 319 #define CONFIG_ETHPRIME         "eTSEC1"
 320
 321 #define CONFIG_PHY_GIGE         /* Include GbE speed/duplex detection */
 322 #endif
 323
 324 /*
 325  * Environment
 326  */
 327 #define CONFIG_ENV_IS_IN_FLASH
 328 #define CONFIG_ENV_OVERWRITE
 329 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 330 #define CONFIG_ENV_SIZE         0x2000
 331 #define CONFIG_ENV_SECT_SIZE    0x20000
 332
 333 #define CONFIG_LOADS_ECHO
 334 #define CONFIG_SYS_LOADS_BAUD_CHANGE
 335
 336 /*
 337  * Command line configuration.
 338  */
 339 #include <config_cmd_default.h>
 340
 341 #define CONFIG_CMD_IRQ
 342 #define CONFIG_CMD_PING
 343 #define CONFIG_CMD_I2C
 344 #define CONFIG_CMD_MII
 345 #define CONFIG_CMD_ELF
 346 #define CONFIG_CMD_IRQ
 347 #define CONFIG_CMD_SETEXPR
 348
 349 #ifdef CONFIG_PCI
 350 #define CONFIG_CMD_PCI
 351 #define CONFIG_CMD_NET
 352 #endif
 353
 354 /*
 355  * USB
 356  */
 357 #define CONFIG_USB_EHCI
 358
 359 #ifdef CONFIG_USB_EHCI
 360 #define CONFIG_CMD_USB
 361 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET
 362 #define CONFIG_USB_EHCI_FSL
 363 #define CONFIG_USB_STORAGE
 364 #define CONFIG_CMD_FAT
 365 #endif
 366
 367 /*
 368  * Miscellaneous configurable options
 369  */
 370 #define CONFIG_SYS_LONGHELP                     /* undef to save memory */
 371 #define CONFIG_CMDLINE_EDITING                  /* Command-line editing */
 372 #define CONFIG_SYS_LOAD_ADDR    0x2000000       /* default load address */
 373 #define CONFIG_SYS_PROMPT       "=> "           /* Monitor Command Prompt */
 374 #ifdef CONFIG_CMD_KGDB
 375 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size */
 376 #else
 377 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size */
 378 #endif
 379 /* Print Buffer Size */
 380 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 381 #define CONFIG_SYS_MAXARGS      16
 382 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE
 383 #define CONFIG_SYS_HZ           1000
 384
 385 /*
 386  * For booting Linux, the board info and command line data
 387  * have to be in the first 16 MB of memory, since this is
 388  * the maximum mapped by the Linux kernel during initialization.
 389  */
 390 #define CONFIG_SYS_BOOTMAPSZ    (16 << 20)      /* Initial Memory map for Linux*/
 391
 392 /*
 393  * Internal Definitions
 394  *
 395  * Boot Flags
 396  */
 397 #define BOOTFLAG_COLD   0x01            /* Normal Power-On: Boot from FLASH */
 398 #define BOOTFLAG_WARM   0x02            /* Software reboot */
 399
 400 #ifdef CONFIG_CMD_KGDB
 401 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 402 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 403 #endif
 404
 405 /*
 406  * Environment Configuration
 407  */
 408
 409 #define CONFIG_HOSTNAME         p1022ds
 410 #define CONFIG_ROOTPATH         /opt/nfsroot
 411 #define CONFIG_BOOTFILE         uImage
 412 #define CONFIG_UBOOTPATH        u-boot.bin      /* U-Boot image on TFTP server */
 413
 414 #define CONFIG_LOADADDR         1000000
 415
 416 #define CONFIG_BOOTDELAY        10      /* -1 disables auto-boot */
 417 #define CONFIG_BOOTARGS
 418
 419 #define CONFIG_BAUDRATE 115200
 420
 421 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 422         "perf_mode=stable\0"                                            \
 423         "memctl_intlv_ctl=2\0"                                          \
 424         "netdev=eth0\0"                                                 \
 425         "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"                          \
 426         "tftpflash=tftpboot $loadaddr $uboot; "                         \
 427                 "protect off " MK_STR(TEXT_BASE) " +$filesize; "        \
 428                 "erase " MK_STR(TEXT_BASE) " +$filesize; "              \
 429                 "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; "      \
 430                 "protect on " MK_STR(TEXT_BASE) " +$filesize; "         \
 431                 "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0"     \
 432         "consoledev=ttyS0\0"                                            \
 433         "ramdiskaddr=2000000\0"                                         \
 434         "ramdiskfile=uramdisk\0"                                        \
 435         "fdtaddr=c00000\0"                                              \
 436         "fdtfile=p1022ds.dtb\0"                                         \
 437         "bdev=sda3\0"                                                   \
 438         "diuregs=md e002c000 1d\0"                                      \
 439         "dium=mw e002c01c\0"                                            \
 440         "diuerr=md e002c014 1\0"                                        \
 441         "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 tty0\0" \
 442         "monitor=0-DVI\0"
 443
 444 #define CONFIG_HDBOOT                                   \
 445         "setenv bootargs root=/dev/$bdev rw "           \
 446         "console=$consoledev,$baudrate $othbootargs;"   \
 447         "tftp $loadaddr $bootfile;"                     \
 448         "tftp $fdtaddr $fdtfile;"                       \
 449         "bootm $loadaddr - $fdtaddr"
 450
 451 #define CONFIG_NFSBOOTCOMMAND                                           \
 452         "setenv bootargs root=/dev/nfs rw "                             \
 453         "nfsroot=$serverip:$rootpath "                                  \
 454         "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
 455         "console=$consoledev,$baudrate $othbootargs;"                   \
 456         "tftp $loadaddr $bootfile;"                                     \
 457         "tftp $fdtaddr $fdtfile;"                                       \
 458         "bootm $loadaddr - $fdtaddr"
 459
 460 #define CONFIG_RAMBOOTCOMMAND                                           \
 461         "setenv bootargs root=/dev/ram rw "                             \
 462         "console=$consoledev,$baudrate $othbootargs;"                   \
 463         "tftp $ramdiskaddr $ramdiskfile;"                               \
 464         "tftp $loadaddr $bootfile;"                                     \
 465         "tftp $fdtaddr $fdtfile;"                                       \
 466         "bootm $loadaddr $ramdiskaddr $fdtaddr"
 467
 468 #define CONFIG_BOOTCOMMAND              CONFIG_RAMBOOTCOMMAND
 469
 470 #endif