include/configs/PIP405.h

   1 /*
   2  * (C) Copyright 2001
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * board/config.h - configuration options, board specific
  10  */
  11
  12 #ifndef __CONFIG_H
  13 #define __CONFIG_H
  14
  15 /***********************************************************
  16  * High Level Configuration Options
  17  * (easy to change)
  18  ***********************************************************/
  19 #define CONFIG_405GP            1       /* This is a PPC405 CPU         */
  20 #define CONFIG_PIP405           1       /* ...on a PIP405 board         */
  21
  22 #define CONFIG_SYS_TEXT_BASE    0xFFF80000
  23
  24 /***********************************************************
  25  * Clock
  26  ***********************************************************/
  27 #define CONFIG_SYS_CLK_FREQ     33000000 /* external frequency to pll   */
  28
  29 /*
  30  * BOOTP options
  31  */
  32 #define CONFIG_BOOTP_BOOTFILESIZE
  33 #define CONFIG_BOOTP_BOOTPATH
  34 #define CONFIG_BOOTP_GATEWAY
  35 #define CONFIG_BOOTP_HOSTNAME
  36
  37 /*
  38  * Command line configuration.
  39  */
  40 #define CONFIG_CMD_IDE
  41 #define CONFIG_CMD_PCI
  42 #define CONFIG_CMD_CACHE
  43 #define CONFIG_CMD_IRQ
  44 #define CONFIG_CMD_EEPROM
  45 #define CONFIG_CMD_REGINFO
  46 #define CONFIG_CMD_FDC
  47 #define CONFIG_CMD_SCSI
  48 #define CONFIG_CMD_FAT
  49 #define CONFIG_CMD_DATE
  50 #define CONFIG_CMD_MII
  51 #define CONFIG_CMD_SDRAM
  52 #define CONFIG_CMD_SAVES
  53 #define CONFIG_CMD_BSP
  54
  55 /**************************************************************
  56  * I2C Stuff:
  57  * the PIP405 is equiped with an Atmel 24C128/256 EEPROM at address
  58  * 0x53.
  59  * Caution: on the same bus is the SPD (Serial Presens Detect
  60  * EEPROM of the SDRAM
  61  * The Atmel EEPROM uses 16Bit addressing.
  62  ***************************************************************/
  63 #define CONFIG_SYS_I2C
  64 #define CONFIG_SYS_I2C_PPC4XX
  65 #define CONFIG_SYS_I2C_PPC4XX_CH0
  66 #define CONFIG_SYS_I2C_PPC4XX_SPEED_0           50000
  67 #define CONFIG_SYS_I2C_PPC4XX_SLAVE_0           0x7F
  68
  69 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x53
  70 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  2
  71 #define CONFIG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
  72 #define CONFIG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
  73 #define CONFIG_ENV_SIZE            0x800   /* 2 kBytes may be used for env vars */
  74
  75 #undef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
  76 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6     /* The Atmel 24C128/256 has     */
  77                                         /* 64 byte page write mode using*/
  78                                         /* last 6 bits of the address   */
  79 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* and takes up to 10 msec */
  80
  81 /***************************************************************
  82  * Definitions for Serial Presence Detect EEPROM address
  83  * (to get SDRAM settings)
  84  ***************************************************************/
  85 #define SPD_EEPROM_ADDRESS      0x50
  86
  87 #define CONFIG_BOARD_EARLY_INIT_F
  88 #define CONFIG_BOARD_EARLY_INIT_R
  89
  90 /**************************************************************
  91  * Environment definitions
  92  **************************************************************/
  93 #define CONFIG_BAUDRATE         9600    /* STD Baudrate */
  94
  95 #define CONFIG_BOOTDELAY        5
  96 /* autoboot (do NOT change this set environment variable "bootdelay" to -1 instead) */
  97 /* #define CONFIG_BOOT_RETRY_TIME       -10     /XXX* feature is available but not enabled */
  98 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check console even if bootdelay = 0 */
  99
 100 #define CONFIG_BOOTCOMMAND      "diskboot 400000 0:1; bootm" /* autoboot command                */
 101 #define CONFIG_BOOTARGS         "console=ttyS0,9600 root=/dev/hda5" /* boot arguments */
 102
 103 #define CONFIG_IPADDR           10.0.0.100
 104 #define CONFIG_SERVERIP         10.0.0.1
 105 #define CONFIG_PREBOOT
 106 /***************************************************************
 107  * defines if the console is stored in the environment
 108  ***************************************************************/
 109 #define CONFIG_SYS_CONSOLE_IS_IN_ENV    /* stdin, stdout and stderr are in evironment */
 110 /***************************************************************
 111  * defines if an overwrite_console function exists
 112  *************************************************************/
 113 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
 114 #define CONFIG_SYS_CONSOLE_INFO_QUIET
 115 /***************************************************************
 116  * defines if the overwrite_console should be stored in the
 117  * environment
 118  **************************************************************/
 119 #undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE
 120
 121 /**************************************************************
 122  * loads config
 123  *************************************************************/
 124 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download  */
 125 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change        */
 126
 127 #define CONFIG_MISC_INIT_R
 128 /***********************************************************
 129  * Miscellaneous configurable options
 130  **********************************************************/
 131 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
 132 #if defined(CONFIG_CMD_KGDB)
 133 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size      */
 134 #else
 135 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size      */
 136 #endif
 137 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 138 #define CONFIG_SYS_MAXARGS      16              /* max number of command args   */
 139 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 140
 141 #define CONFIG_SYS_MEMTEST_START        0x0100000       /* memtest works on     */
 142 #define CONFIG_SYS_MEMTEST_END          0x0C00000       /* 1 ... 12 MB in DRAM  */
 143
 144 #define CONFIG_CONS_INDEX       1       /* Use UART0                    */
 145 #define CONFIG_SYS_NS16550_SERIAL
 146 #define CONFIG_SYS_NS16550_REG_SIZE     1
 147 #define CONFIG_SYS_NS16550_CLK          get_serial_clock()
 148
 149 #undef  CONFIG_SYS_EXT_SERIAL_CLOCK            /* no external serial clock used */
 150 #define CONFIG_SYS_BASE_BAUD       691200
 151
 152 /* The following table includes the supported baudrates */
 153 #define CONFIG_SYS_BAUDRATE_TABLE       \
 154         { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 155          57600, 115200, 230400, 460800, 921600 }
 156
 157 #define CONFIG_SYS_LOAD_ADDR            0x400000        /* default load address */
 158 #define CONFIG_SYS_EXTBDINFO            1       /* To use extended board_into (bd_t) */
 159
 160 /*-----------------------------------------------------------------------
 161  * PCI stuff
 162  *-----------------------------------------------------------------------
 163  */
 164 #define PCI_HOST_ADAPTER 0              /* configure ar pci adapter     */
 165 #define PCI_HOST_FORCE  1               /* configure as pci host        */
 166 #define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
 167
 168 #define CONFIG_PCI                      /* include pci support          */
 169 #define CONFIG_PCI_INDIRECT_BRIDGE      /* indirect PCI bridge support */
 170 #define CONFIG_PCI_HOST PCI_HOST_FORCE  /* configure as pci-host        */
 171 #define CONFIG_PCI_PNP                  /* pci plug-and-play            */
 172                                         /* resource configuration       */
 173 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000   /* PCI Vendor ID: to-do!!!      */
 174 #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000   /* PCI Device ID: to-do!!!      */
 175 #define CONFIG_SYS_PCI_PTM1LA   0x00000000      /* point to sdram               */
 176 #define CONFIG_SYS_PCI_PTM1MS   0x80000001      /* 2GB, enable hard-wired to 1  */
 177 #define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
 178 #define CONFIG_SYS_PCI_PTM2LA   0x00000000      /* disabled                     */
 179 #define CONFIG_SYS_PCI_PTM2MS   0x00000000      /* disabled                     */
 180 #define CONFIG_SYS_PCI_PTM2PCI 0x00000000      /* Host: use this pci address   */
 181
 182 /*-----------------------------------------------------------------------
 183  * Start addresses for the final memory configuration
 184  * (Set up by the startup code)
 185  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 186  */
 187 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 188 #define CONFIG_SYS_FLASH_BASE           0xFFF80000
 189 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
 190 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)    /* Reserve 512 kB for Monitor   */
 191 #define CONFIG_SYS_MALLOC_LEN           (1024 * 1024)   /* Reserve 1024 kB for malloc() */
 192
 193 /*
 194  * For booting Linux, the board info and command line data
 195  * have to be in the first 8 MB of memory, since this is
 196  * the maximum mapped by the Linux kernel during initialization.
 197  */
 198 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 199 /*-----------------------------------------------------------------------
 200  * FLASH organization
 201  */
 202 #define CONFIG_SYS_UPDATE_FLASH_SIZE
 203 #define CONFIG_SYS_FLASH_PROTECTION
 204 #define CONFIG_SYS_FLASH_EMPTY_INFO
 205
 206 #define CONFIG_SYS_FLASH_CFI
 207 #define CONFIG_FLASH_CFI_DRIVER
 208
 209 #define CONFIG_FLASH_SHOW_PROGRESS      45
 210
 211 #define CONFIG_SYS_MAX_FLASH_BANKS      1
 212 #define CONFIG_SYS_MAX_FLASH_SECT       256
 213
 214 /*
 215  * Init Memory Controller:
 216  */
 217 #define FLASH_MAX_SIZE          0x00800000              /* 8MByte max */
 218 #define FLASH_BASE_PRELIM       0xFF800000  /* open the flash CS */
 219 /* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
 220 #define FLASH_SIZE_PRELIM        3  /* maximal flash FLASH size bank #0 */
 221
 222 #define CONFIG_BOARD_EARLY_INIT_F
 223
 224 /* Configuration Port location */
 225 #define CONFIG_PORT_ADDR        0xF4000000
 226 #define MULTI_PURPOSE_SOCKET_ADDR 0xF8000000
 227
 228 /*-----------------------------------------------------------------------
 229  * Definitions for initial stack pointer and data area (in On Chip SRAM)
 230  */
 231 #define CONFIG_SYS_TEMP_STACK_OCM       1
 232 #define CONFIG_SYS_OCM_DATA_ADDR        0xF0000000
 233 #define CONFIG_SYS_OCM_DATA_SIZE        0x1000
 234 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_OCM_DATA_ADDR        /* inside of On Chip SRAM    */
 235 #define CONFIG_SYS_INIT_RAM_SIZE        CONFIG_SYS_OCM_DATA_SIZE        /* Size of On Chip SRAM        */
 236 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 237 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 238
 239 /***********************************************************************
 240  * External peripheral base address
 241  ***********************************************************************/
 242 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS 0xE8000000
 243
 244 /***********************************************************************
 245  * Last Stage Init
 246  ***********************************************************************/
 247 #define CONFIG_LAST_STAGE_INIT
 248 /************************************************************
 249  * Ethernet Stuff
 250  ***********************************************************/
 251 #define CONFIG_PPC4xx_EMAC
 252 #define CONFIG_MII              1       /* MII PHY management           */
 253 #define CONFIG_PHY_ADDR         1       /* PHY address                  */
 254 /************************************************************
 255  * RTC
 256  ***********************************************************/
 257 #define CONFIG_RTC_MC146818
 258 #undef CONFIG_WATCHDOG                  /* watchdog disabled            */
 259
 260 /************************************************************
 261  * IDE/ATA stuff
 262  ************************************************************/
 263 #define CONFIG_SYS_IDE_MAXBUS           2   /* max. 2 IDE busses        */
 264 #define CONFIG_SYS_IDE_MAXDEVICE        (CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
 265
 266 #define CONFIG_SYS_ATA_BASE_ADDR        CONFIG_SYS_ISA_IO_BASE_ADDRESS /* base address */
 267 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x01F0  /* ide0 offste */
 268 #define CONFIG_SYS_ATA_IDE1_OFFSET      0x0170  /* ide1 offset */
 269 #define CONFIG_SYS_ATA_DATA_OFFSET      0       /* data reg offset      */
 270 #define CONFIG_SYS_ATA_REG_OFFSET       0       /* reg offset */
 271 #define CONFIG_SYS_ATA_ALT_OFFSET       0x200   /* alternate register offset */
 272
 273 #undef  CONFIG_IDE_8xx_DIRECT           /* no pcmcia interface required */
 274 #undef  CONFIG_IDE_LED                  /* no led for ide supported     */
 275 #define CONFIG_IDE_RESET                /* reset for ide supported...   */
 276 #define CONFIG_IDE_RESET_ROUTINE        /* with a special reset function */
 277 #define CONFIG_SUPPORT_VFAT
 278
 279 /************************************************************
 280  * ATAPI support (experimental)
 281  ************************************************************/
 282 #define CONFIG_ATAPI                    /* enable ATAPI Support */
 283
 284 /************************************************************
 285  * SCSI support (experimental) only SYM53C8xx supported
 286  ************************************************************/
 287 #define CONFIG_SCSI_SYM53C8XX
 288 #define CONFIG_SYS_SCSI_MAX_LUN 8       /* number of supported LUNs */
 289 #define CONFIG_SYS_SCSI_MAX_SCSI_ID     7       /* maximum SCSI ID (0..6) */
 290 #define CONFIG_SYS_SCSI_MAX_DEVICE      CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN /* maximum Target devices */
 291 #define CONFIG_SYS_SCSI_SPIN_UP_TIME    2
 292
 293 /************************************************************
 294  * Disk-On-Chip configuration
 295  ************************************************************/
 296 #define CONFIG_SYS_MAX_DOC_DEVICE       1       /* Max number of DOC devices            */
 297 #define CONFIG_SYS_DOC_SHORT_TIMEOUT
 298 #define CONFIG_SYS_DOC_SUPPORT_2000
 299 #define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
 300
 301 /************************************************************
 302  * DISK Partition support
 303  ************************************************************/
 304 #define CONFIG_DOS_PARTITION
 305 #define CONFIG_MAC_PARTITION
 306 #define CONFIG_ISO_PARTITION /* Experimental */
 307
 308 /************************************************************
 309  * Video support
 310  ************************************************************/
 311 #define CONFIG_VIDEO                    /*To enable video controller support */
 312 #define CONFIG_VIDEO_CT69000
 313 #define CONFIG_CFB_CONSOLE
 314 #define CONFIG_VIDEO_LOGO
 315 #define CONFIG_CONSOLE_EXTRA_INFO
 316 #define CONFIG_VGA_AS_SINGLE_DEVICE
 317 #define CONFIG_VIDEO_SW_CURSOR
 318 #define CONFIG_VIDEO_ONBOARD            /* Video controller is on-board */
 319
 320 /************************************************************
 321  * USB support
 322  ************************************************************/
 323 #define CONFIG_USB_UHCI
 324 #define CONFIG_USB_KEYBOARD
 325 #define CONFIG_USB_STORAGE
 326
 327 /* Enable needed helper functions */
 328 #define CONFIG_SYS_STDIO_DEREGISTER             /* needs stdio_deregister */
 329
 330 /************************************************************
 331  * Debug support
 332  ************************************************************/
 333 #if defined(CONFIG_CMD_KGDB)
 334 #define CONFIG_KGDB_BAUDRATE    230400  /* speed to run kgdb serial port */
 335 #endif
 336
 337 /************************************************************
 338  * support BZIP2 compression
 339  ************************************************************/
 340 #define CONFIG_BZIP2            1
 341
 342 /************************************************************
 343  * Ident
 344  ************************************************************/
 345 #define VERSION_TAG "released"
 346 #define CONFIG_ISO_STRING "MEV-10066-001"
 347 #define CONFIG_IDENT_STRING "\n(c) 2002 by MPL AG Switzerland, " CONFIG_ISO_STRING " " VERSION_TAG
 348
 349 #endif  /* __CONFIG_H */