pci: move pcidelay code to new location just before PCI bus scan

[people/ms/u-boot.git] / include / configs / PLU405.h

/*
 * (C) Copyright 2001-2003
 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

/*
 * board/config.h - configuration options, board specific
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_405EP            1       /* This is a PPC405 CPU         */
#define CONFIG_4xx              1       /* ...member of PPC4xx family   */
#define CONFIG_PLU405           1       /* ...on a PLU405 board         */

#define CONFIG_SYS_TEXT_BASE    0xFFF80000

#define CONFIG_BOARD_EARLY_INIT_F 1     /* call board_early_init_f()    */
#define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */

#define CONFIG_SYS_CLK_FREQ     33333400 /* external frequency to pll   */

#define CONFIG_BAUDRATE         9600

#undef  CONFIG_BOOTARGS
#undef  CONFIG_BOOTCOMMAND

#define CONFIG_PREBOOT                  /* enable preboot variable      */

#define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change        */

#undef  CONFIG_HAS_ETH1

#define CONFIG_PPC4xx_EMAC
#define CONFIG_MII              1       /* MII PHY management           */
#define CONFIG_PHY_ADDR         0       /* PHY address                  */
#define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
#define CONFIG_RESET_PHY_R      1       /* use reset_phy()              */

#define CONFIG_PHY_CLK_FREQ     EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/


/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_DHCP
#define CONFIG_CMD_PCI
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_IDE
#define CONFIG_CMD_FAT
#define CONFIG_CMD_ELF
#define CONFIG_CMD_NAND
#define CONFIG_CMD_DATE
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_USB

#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP

#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION

#define CONFIG_SUPPORT_VFAT

#undef  CONFIG_WATCHDOG                 /* watchdog disabled            */

#define CONFIG_RTC_MC146818             /* DS1685 is MC146818 compatible*/
#define CONFIG_SYS_RTC_REG_BASE_ADDR     0xF0000500 /* RTC Base Address         */

#define CONFIG_SDRAM_BANK0      1       /* init onboard SDRAM bank 0    */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
#define CONFIG_SYS_PROMPT       "=> "           /* Monitor Command Prompt       */

#undef  CONFIG_SYS_HUSH_PARSER                  /* use "hush" command parser    */
#ifdef  CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
#endif

#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size      */
#else
#define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size      */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS      16              /* max number of command args   */
#define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */

#define CONFIG_SYS_DEVICE_NULLDEV       1       /* include nulldev device       */

#define CONFIG_SYS_CONSOLE_INFO_QUIET   1       /* don't print console @ startup*/

#define CONFIG_AUTO_COMPLETE    1       /* add autocompletion support   */

#define CONFIG_SYS_MEMTEST_START        0x0400000       /* memtest works on     */
#define CONFIG_SYS_MEMTEST_END          0x0C00000       /* 4 ... 12 MB in DRAM  */

#define CONFIG_CONS_INDEX       1       /* Use UART0                    */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          get_serial_clock()

#undef  CONFIG_SYS_EXT_SERIAL_CLOCK            /* no external serial clock used */
#define CONFIG_SYS_BASE_BAUD        691200

/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE       \
        { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
         57600, 115200, 230400, 460800, 921600 }

#define CONFIG_SYS_LOAD_ADDR    0x100000        /* default load address */
#define CONFIG_SYS_EXTBDINFO    1               /* To use extended board_into (bd_t) */

#define CONFIG_SYS_HZ           1000            /* decrementer freq: 1 ms ticks */

#define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
#define CONFIG_ZERO_BOOTDELAY_CHECK     /* check for keypress on bootdelay==0 */
#define CONFIG_BOOTDELAY        3       /* autoboot after 3 seconds     */

/* Only interrupt boot if space is pressed */
/* If a long serial cable is connected but */
/* other end is dead, garbage will be read */
#define CONFIG_AUTOBOOT_KEYED   1
#define CONFIG_AUTOBOOT_PROMPT  \
        "Press SPACE to abort autoboot in %d seconds\n", bootdelay
#undef CONFIG_AUTOBOOT_DELAY_STR
#define CONFIG_AUTOBOOT_STOP_STR " "

#define CONFIG_VERSION_VARIABLE 1       /* include version env variable */

#define CONFIG_SYS_RX_ETH_BUFFER        16      /* use 16 rx buffer on 405 emac */

/*
 * NAND-FLASH stuff
 */
#define CONFIG_SYS_NAND_BASE_LIST       {CONFIG_SYS_NAND_BASE}
#define CONFIG_SYS_MAX_NAND_DEVICE      1         /* Max number of NAND devices */
#define NAND_BIG_DELAY_US       25

#define CONFIG_SYS_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
#define CONFIG_SYS_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
#define CONFIG_SYS_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
#define CONFIG_SYS_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */

#define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
#define CONFIG_SYS_NAND_QUIET          1

/*
 * PCI stuff
 */
#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
#define PCI_HOST_FORCE  1               /* configure as pci host        */
#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */

#define CONFIG_PCI                      /* include pci support          */
#define CONFIG_PCI_HOST PCI_HOST_FORCE  /* select pci host function     */
#define CONFIG_PCI_PNP                  /* do pci plug-and-play         */
                                        /* resource configuration       */

#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */

#define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/

#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
#define CONFIG_SYS_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
#define CONFIG_SYS_PCI_PTM1LA  0x00000000      /* point to sdram               */
#define CONFIG_SYS_PCI_PTM1MS  0xf8000001      /* 128MB, enable hard-wired to 1 */
#define CONFIG_SYS_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
#define CONFIG_SYS_PCI_PTM2LA  0xffc00000      /* point to flash               */
#define CONFIG_SYS_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
#define CONFIG_SYS_PCI_PTM2PCI 0x08000000      /* Host: use this pci address   */

/*
 * IDE/ATA stuff
 */
#undef  CONFIG_IDE_8xx_DIRECT               /* no pcmcia interface required */
#undef  CONFIG_IDE_LED                  /* no led for ide supported     */
#define CONFIG_IDE_RESET        1       /* reset for ide supported      */

#define CONFIG_SYS_IDE_MAXBUS           1               /* max. 1 IDE busses    */
/* max. 1 drives per IDE bus */
#define CONFIG_SYS_IDE_MAXDEVICE        (CONFIG_SYS_IDE_MAXBUS*1)

#define CONFIG_SYS_ATA_BASE_ADDR        0xF0100000
#define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000

#define CONFIG_SYS_ATA_DATA_OFFSET      0x0000  /* Offset for data I/O */
#define CONFIG_SYS_ATA_REG_OFFSET       0x0000  /* Offset for normal register access */
#define CONFIG_SYS_ATA_ALT_OFFSET       0x0000  /* Offset for alternate registers */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ            (8 << 20) /* Initial Memory map for Linux */

/*
 * FLASH organization
 */
#define FLASH_BASE0_PRELIM      0xFFC00000 /* FLASH bank #0 */

#define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT       256     /* max number of sectors on one chip */

#define CONFIG_SYS_FLASH_ERASE_TOUT     120000  /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT     1000    /* Timeout for Flash Write (in ms) */

#define CONFIG_SYS_FLASH_WORD_SIZE      unsigned short  /* flash word size (width) */
#define CONFIG_SYS_FLASH_ADDR0          0x5555  /* 1st addr for flash config cycles */
#define CONFIG_SYS_FLASH_ADDR1          0x2AAA  /* 2nd addr for flash config cycles */
/*
 * The following defines are added for buggy IOP480 byte interface.
 * All other boards should use the standard values (CPCI405 etc.)
 */
#define CONFIG_SYS_FLASH_READ0          0x0000  /* 0 is standard */
#define CONFIG_SYS_FLASH_READ1          0x0001  /* 1 is standard */
#define CONFIG_SYS_FLASH_READ2          0x0002  /* 2 is standard */

#define CONFIG_SYS_FLASH_EMPTY_INFO             /* print 'E' for empty sector */

/*
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define CONFIG_SYS_SDRAM_BASE           0x00000000
#define CONFIG_SYS_FLASH_BASE           CONFIG_SYS_MONITOR_BASE
#define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_MONITOR_LEN          (~(CONFIG_SYS_TEXT_BASE) + 1)
#define CONFIG_SYS_MALLOC_LEN           (1024 << 10)

/*
 * Environment Variable setup
 */
#define CONFIG_ENV_IS_IN_EEPROM 1       /* use EEPROM for environment vars */
#define CONFIG_ENV_OFFSET               0x100   /* reseve 0x100 bytes for strapping */
#define CONFIG_ENV_SIZE         0x700

/*
 * I2C EEPROM (24WC16) for environment
 */
#define CONFIG_HARD_I2C                 /* I2c with hardware support */
#define CONFIG_PPC4XX_I2C               /* use PPC4xx driver            */
#define CONFIG_SYS_I2C_SPEED            400000  /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE            0x7F

#define CONFIG_SYS_I2C_EEPROM_ADDR      0x50    /* EEPROM 24WC16 */
#define CONFIG_SYS_EEPROM_WREN         1

/* 24WC16 */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1        /* Bytes of address             */
/* mask of address bits that overflow into the "EEPROM chip address"    */
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW     0x07
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4     /* The 24WC16 has   */
                                        /* 16 byte page write mode using */
                                        /* last 4 bits of the address   */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10   /* and takes up to 10 msec */

/*
 * External Bus Controller (EBC) Setup
 */
#define CAN0_BA         0xF0000000          /* CAN0 Base Address        */
#define CAN1_BA         0xF0000100          /* CAN1 Base Address        */
#define DUART0_BA       0xF0000400          /* DUART Base Address       */
#define DUART1_BA       0xF0000408          /* DUART Base Address       */
#define RTC_BA          0xF0000500          /* RTC Base Address         */
#define VGA_BA          0xF1000000          /* Epson VGA Base Address   */
#define CONFIG_SYS_NAND_BASE    0xF4000000          /* NAND FLASH Base Address  */

/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
/* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
#define CONFIG_SYS_EBC_PB0AP            0x92015480
/* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
#define CONFIG_SYS_EBC_PB0CR            0xFFC5A000

/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
#define CONFIG_SYS_EBC_PB1AP            0x92015480
/* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
#define CONFIG_SYS_EBC_PB1CR            0xF4018000

/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
/* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CONFIG_SYS_EBC_PB2AP            0x010053C0
/* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
#define CONFIG_SYS_EBC_PB2CR            0xF0018000

/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
/* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CONFIG_SYS_EBC_PB3AP            0x010053C0
/* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
#define CONFIG_SYS_EBC_PB3CR            0xF011A000

/*
 * FPGA stuff
 */
#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0100100        /* FPGA internal Base Address */

/* FPGA internal regs */
#define CONFIG_SYS_FPGA_CTRL            0x000

/* FPGA Control Reg */
#define CONFIG_SYS_FPGA_CTRL_CF_RESET   0x0001
#define CONFIG_SYS_FPGA_CTRL_WDI        0x0002
#define CONFIG_SYS_FPGA_CTRL_PS2_RESET 0x0020

#define CONFIG_SYS_FPGA_SPARTAN2        1           /* using Xilinx Spartan 2 now */
#define CONFIG_SYS_FPGA_MAX_SIZE        128*1024    /* 128kByte is enough for XC2S50E*/

/* FPGA program pin configuration */
#define CONFIG_SYS_FPGA_PRG             0x04000000  /* FPGA program pin (ppc output) */
#define CONFIG_SYS_FPGA_CLK             0x02000000  /* FPGA clk pin (ppc output) */
#define CONFIG_SYS_FPGA_DATA            0x01000000  /* FPGA data pin (ppc output) */
#define CONFIG_SYS_FPGA_INIT            0x00010000  /* FPGA init pin (ppc input) */
#define CONFIG_SYS_FPGA_DONE            0x00008000  /* FPGA done pin (ppc input) */

/*
 * Definitions for initial stack pointer and data area (in data cache)
 */
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
#define CONFIG_SYS_TEMP_STACK_OCM         1

/* On Chip Memory location */
#define CONFIG_SYS_OCM_DATA_ADDR        0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE        0x1000
#define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
#define CONFIG_SYS_INIT_RAM_SIZE        CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM  */

#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET

/*
 * Definitions for GPIO setup (PPC405EP specific)
 *
 * GPIO0[0]     - External Bus Controller BLAST output
 * GPIO0[1-9]   - Instruction trace outputs -> GPIO
 * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
 * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
 * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
 * GPIO0[24-27] - UART0 control signal inputs/outputs
 * GPIO0[28-29] - UART1 data signal input/output
 * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
 */
#define CONFIG_SYS_GPIO0_OSRL           0x00000550
#define CONFIG_SYS_GPIO0_OSRH           0x00000110
#define CONFIG_SYS_GPIO0_ISR1L          0x00000000
#define CONFIG_SYS_GPIO0_ISR1H          0x15555445
#define CONFIG_SYS_GPIO0_TSRL           0x00000000
#define CONFIG_SYS_GPIO0_TSRH           0x00000000
#define CONFIG_SYS_GPIO0_TCR            0x77FE0014

#define CONFIG_SYS_DUART_RST            (0x80000000 >> 14)
#define CONFIG_SYS_EEPROM_WP            (0x80000000 >> 0)

/*
 * Default speed selection (cpu_plb_opb_ebc) in MHz.
 * This value will be set if iic boot eprom is disabled.
 */
#if 1
#define PLLMR0_DEFAULT   PLLMR0_266_133_66_33
#define PLLMR1_DEFAULT   PLLMR1_266_133_66_33
#endif
#if 0
#define PLLMR0_DEFAULT   PLLMR0_200_100_50_33
#define PLLMR1_DEFAULT   PLLMR1_200_100_50_33
#endif
#if 0
#define PLLMR0_DEFAULT   PLLMR0_133_66_66_33
#define PLLMR1_DEFAULT   PLLMR1_133_66_66_33
#endif

/*
 * PCI OHCI controller
 */
#define CONFIG_USB_OHCI_NEW     1
#define CONFIG_PCI_OHCI         1
#define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
#define CONFIG_SYS_USB_OHCI_SLOT_NAME   "ohci_pci"
#define CONFIG_USB_STORAGE      1

/*
 * UBI
 */
#define CONFIG_CMD_UBI
#define CONFIG_RBTREE
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_CMD_MTDPARTS
#define CONFIG_LZO

#endif  /* __CONFIG_H */