include/configs/PM828.h

   1 /*
   2  * (C) Copyright 2001-2005
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * See file CREDITS for list of people who contributed to this
   6  * project.
   7  *
   8  * This program is free software; you can redistribute it and/or
   9  * modify it under the terms of the GNU General Public License as
  10  * published by the Free Software Foundation; either version 2 of
  11  * the License, or (at your option) any later version.
  12  *
  13  * This program is distributed in the hope that it will be useful,
  14  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  16  * GNU General Public License for more details.
  17  *
  18  * You should have received a copy of the GNU General Public License
  19  * along with this program; if not, write to the Free Software
  20  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  21  * MA 02111-1307 USA
  22  */
  23
  24 /*
  25  * board/config.h - configuration options, board specific
  26  */
  27
  28 #ifndef __CONFIG_H
  29 #define __CONFIG_H
  30
  31 #undef CONFIG_SYS_RAMBOOT
  32
  33 /*
  34  * High Level Configuration Options
  35  * (easy to change)
  36  */
  37
  38 #define CONFIG_MPC8260          1       /* This is a MPC8260 CPU        */
  39 #define CONFIG_PM828            1       /* ...on a PM828 module */
  40 #define CONFIG_CPM2             1       /* Has a CPM2 */
  41
  42 #undef CONFIG_DB_CR826_J30x_ON          /* J30x jumpers on D.B. carrier */
  43
  44 #define CONFIG_BOOTDELAY        5       /* autoboot after 5 seconds     */
  45
  46 #define CONFIG_PREBOOT  "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
  47
  48 #undef  CONFIG_BOOTARGS
  49 #define CONFIG_BOOTCOMMAND                                                      \
  50         "bootp;"                                                                \
  51         "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "     \
  52         "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;"    \
  53         "bootm"
  54
  55 /* enable I2C and select the hardware/software driver */
  56 #undef  CONFIG_HARD_I2C
  57 #define CONFIG_SOFT_I2C         1       /* I2C bit-banged               */
  58 # define CONFIG_SYS_I2C_SPEED           50000
  59 # define CONFIG_SYS_I2C_SLAVE           0xFE
  60 /*
  61  * Software (bit-bang) I2C driver configuration
  62  */
  63 #define I2C_PORT        3               /* Port A=0, B=1, C=2, D=3 */
  64 #define I2C_ACTIVE      (iop->pdir |=  0x00010000)
  65 #define I2C_TRISTATE    (iop->pdir &= ~0x00010000)
  66 #define I2C_READ        ((iop->pdat & 0x00010000) != 0)
  67 #define I2C_SDA(bit)    if(bit) iop->pdat |=  0x00010000; \
  68                         else    iop->pdat &= ~0x00010000
  69 #define I2C_SCL(bit)    if(bit) iop->pdat |=  0x00020000; \
  70                         else    iop->pdat &= ~0x00020000
  71 #define I2C_DELAY       udelay(5)       /* 1/4 I2C clock duration */
  72
  73
  74 #define CONFIG_RTC_PCF8563
  75 #define CONFIG_SYS_I2C_RTC_ADDR 0x51
  76
  77 /*
  78  * select serial console configuration
  79  *
  80  * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
  81  * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
  82  * for SCC).
  83  *
  84  * if CONFIG_CONS_NONE is defined, then the serial console routines must
  85  * defined elsewhere (for example, on the cogent platform, there are serial
  86  * ports on the motherboard which are used for the serial console - see
  87  * cogent/cma101/serial.[ch]).
  88  */
  89 #define CONFIG_CONS_ON_SMC              /* define if console on SMC */
  90 #undef  CONFIG_CONS_ON_SCC              /* define if console on SCC */
  91 #undef  CONFIG_CONS_NONE                /* define if console on something else*/
  92 #define CONFIG_CONS_INDEX       2       /* which serial channel for console */
  93
  94 /*
  95  * select ethernet configuration
  96  *
  97  * if CONFIG_ETHER_ON_SCC is selected, then
  98  *   - CONFIG_ETHER_INDEX must be set to the channel number (1-4)
  99  *   - CONFIG_NET_MULTI must not be defined
 100  *
 101  * if CONFIG_ETHER_ON_FCC is selected, then
 102  *   - one or more CONFIG_ETHER_ON_FCCx (x=1,2,3) must also be selected
 103  *   - CONFIG_NET_MULTI must be defined
 104  *
 105  * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
 106  * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
 107  */
 108 #define CONFIG_NET_MULTI
 109 #undef  CONFIG_ETHER_NONE               /* define if ether on something else */
 110
 111 #undef  CONFIG_ETHER_ON_SCC             /* define if ether on SCC       */
 112 #define CONFIG_ETHER_INDEX    1         /* which SCC channel for ethernet */
 113
 114 #define CONFIG_ETHER_ON_FCC             /* define if ether on FCC       */
 115 /*
 116  * - Rx-CLK is CLK11
 117  * - Tx-CLK is CLK10
 118  */
 119 #define CONFIG_ETHER_ON_FCC1
 120 # define CONFIG_SYS_CMXFCR_MASK1        (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
 121 #ifndef CONFIG_DB_CR826_J30x_ON
 122 # define CONFIG_SYS_CMXFCR_VALUE1       (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK10)
 123 #else
 124 # define CONFIG_SYS_CMXFCR_VALUE1       (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12)
 125 #endif
 126 /*
 127  * - Rx-CLK is CLK15
 128  * - Tx-CLK is CLK14
 129  */
 130 #define CONFIG_ETHER_ON_FCC2
 131 # define CONFIG_SYS_CMXFCR_MASK2        (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
 132 # define CONFIG_SYS_CMXFCR_VALUE2       (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
 133 /*
 134  * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
 135  * - Enable Full Duplex in FSMR
 136  */
 137 # define CONFIG_SYS_CPMFCR_RAMTYPE      0
 138 # define CONFIG_SYS_FCC_PSMR            (FCC_PSMR_FDE|FCC_PSMR_LPB)
 139
 140 /* system clock rate (CLKIN) - equal to the 60x and local bus speed */
 141 #define CONFIG_8260_CLKIN       100000000       /* in Hz */
 142
 143 #if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
 144 #define CONFIG_BAUDRATE         230400
 145 #else
 146 #define CONFIG_BAUDRATE         9600
 147 #endif
 148
 149 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download  */
 150 #undef  CONFIG_SYS_LOADS_BAUD_CHANGE            /* don't allow baudrate change  */
 151
 152 #undef  CONFIG_WATCHDOG                 /* watchdog disabled            */
 153
 154 /*
 155  * BOOTP options
 156  */
 157 #define CONFIG_BOOTP_SUBNETMASK
 158 #define CONFIG_BOOTP_GATEWAY
 159 #define CONFIG_BOOTP_HOSTNAME
 160 #define CONFIG_BOOTP_BOOTPATH
 161 #define CONFIG_BOOTP_BOOTFILESIZE
 162
 163
 164 /*
 165  * Command line configuration.
 166  */
 167 #include <config_cmd_default.h>
 168
 169 #define CONFIG_CMD_BEDBUG
 170 #define CONFIG_CMD_DATE
 171 #define CONFIG_CMD_DHCP
 172 #define CONFIG_CMD_DOC
 173 #define CONFIG_CMD_EEPROM
 174 #define CONFIG_CMD_I2C
 175 #define CONFIG_CMD_NFS
 176 #define CONFIG_CMD_SNTP
 177
 178 #ifdef CONFIG_PCI
 179 #define CONFIG_CMD_PCI
 180 #endif
 181
 182
 183 /*
 184  * Disk-On-Chip configuration
 185  */
 186 #define CONFIG_NAND_LEGACY
 187
 188 #define CONFIG_SYS_DOC_SHORT_TIMEOUT
 189 #define CONFIG_SYS_MAX_DOC_DEVICE       1       /* Max number of DOC devices    */
 190
 191 #define CONFIG_SYS_DOC_SUPPORT_2000
 192 #define CONFIG_SYS_DOC_SUPPORT_MILLENNIUM
 193
 194 /*
 195  * Miscellaneous configurable options
 196  */
 197 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
 198 #define CONFIG_SYS_PROMPT       "=> "           /* Monitor Command Prompt       */
 199 #if defined(CONFIG_CMD_KGDB)
 200 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size      */
 201 #else
 202 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size      */
 203 #endif
 204 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 205 #define CONFIG_SYS_MAXARGS      16              /* max number of command args   */
 206 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 207
 208 #define CONFIG_SYS_MEMTEST_START        0x0400000       /* memtest works on     */
 209 #define CONFIG_SYS_MEMTEST_END 0x0C00000        /* 4 ... 12 MB in DRAM  */
 210
 211 #define CONFIG_SYS_LOAD_ADDR    0x100000        /* default load address */
 212
 213 #define CONFIG_SYS_HZ           1000            /* decrementer freq: 1 ms ticks */
 214
 215 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
 216
 217 #define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC     /* "bad" address                */
 218
 219 /*
 220  * For booting Linux, the board info and command line data
 221  * have to be in the first 8 MB of memory, since this is
 222  * the maximum mapped by the Linux kernel during initialization.
 223  */
 224 #define CONFIG_SYS_BOOTMAPSZ         (8 << 20)       /* Initial Memory map for Linux */
 225
 226 /*-----------------------------------------------------------------------
 227  * Flash and Boot ROM mapping
 228  */
 229
 230 #define CONFIG_SYS_BOOTROM_BASE 0xFF800000
 231 #define CONFIG_SYS_BOOTROM_SIZE 0x00080000
 232 #define CONFIG_SYS_FLASH0_BASE          0x40000000
 233 #define CONFIG_SYS_FLASH0_SIZE          0x02000000
 234 #define CONFIG_SYS_DOC_BASE             0xFF800000
 235 #define CONFIG_SYS_DOC_SIZE             0x00100000
 236
 237
 238 /* Flash bank size (for preliminary settings)
 239  */
 240 #define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE
 241
 242 /*-----------------------------------------------------------------------
 243  * FLASH organization
 244  */
 245 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max num of memory banks      */
 246 #define CONFIG_SYS_MAX_FLASH_SECT       135     /* max num of sects on one chip */
 247
 248 #define CONFIG_SYS_FLASH_ERASE_TOUT     240000  /* Flash Erase Timeout (in ms)  */
 249 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (in ms)  */
 250
 251 #if 0
 252 /* Start port with environment in flash; switch to EEPROM later */
 253 #define CONFIG_ENV_IS_IN_FLASH  1
 254 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE+0x40000)
 255 #define CONFIG_ENV_SIZE         0x40000
 256 #define CONFIG_ENV_SECT_SIZE    0x40000
 257 #else
 258 /* Final version: environment in EEPROM */
 259 #define CONFIG_ENV_IS_IN_EEPROM 1
 260 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x58
 261 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 262 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       4
 263 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* and takes up to 10 msec */
 264 #define CONFIG_ENV_OFFSET               512
 265 #define CONFIG_ENV_SIZE         (2048 - 512)
 266 #endif
 267
 268 /*-----------------------------------------------------------------------
 269  * Hard Reset Configuration Words
 270  *
 271  * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
 272  * defines for the various registers affected by the HRCW e.g. changing
 273  * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
 274  */
 275 #if defined(CONFIG_BOOT_ROM)
 276 #define CONFIG_SYS_HRCW_MASTER          (HRCW_BPS01 | HRCW_CIP | HRCW_ISB100 | HRCW_BMS)
 277 #else
 278 #define CONFIG_SYS_HRCW_MASTER          (HRCW_CIP | HRCW_ISB100 | HRCW_BMS)
 279 #endif
 280
 281 /* no slaves so just fill with zeros */
 282 #define CONFIG_SYS_HRCW_SLAVE1          0
 283 #define CONFIG_SYS_HRCW_SLAVE2          0
 284 #define CONFIG_SYS_HRCW_SLAVE3          0
 285 #define CONFIG_SYS_HRCW_SLAVE4          0
 286 #define CONFIG_SYS_HRCW_SLAVE5          0
 287 #define CONFIG_SYS_HRCW_SLAVE6          0
 288 #define CONFIG_SYS_HRCW_SLAVE7          0
 289
 290 /*-----------------------------------------------------------------------
 291  * Internal Memory Mapped Register
 292  */
 293 #define CONFIG_SYS_IMMR         0xF0000000
 294
 295 /*-----------------------------------------------------------------------
 296  * Definitions for initial stack pointer and data area (in DPRAM)
 297  */
 298 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_IMMR
 299 #define CONFIG_SYS_INIT_RAM_END 0x4000  /* End of used area in DPRAM    */
 300 #define CONFIG_SYS_GBL_DATA_SIZE        128 /* size in bytes reserved for initial data*/
 301 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 302 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 303
 304 /*-----------------------------------------------------------------------
 305  * Start addresses for the final memory configuration
 306  * (Set up by the startup code)
 307  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 308  *
 309  * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE, local SDRAM
 310  * is mapped at SDRAM_BASE2_PRELIM.
 311  */
 312 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 313 #define CONFIG_SYS_FLASH_BASE           CONFIG_SYS_FLASH0_BASE
 314 #define CONFIG_SYS_MONITOR_BASE TEXT_BASE
 315 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for Monitor */
 316 #define CONFIG_SYS_MALLOC_LEN           (128 << 10)     /* Reserve 128 kB for malloc()*/
 317
 318 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 319 # define CONFIG_SYS_RAMBOOT
 320 #endif
 321
 322 #ifdef  CONFIG_PCI
 323 #define CONFIG_PCI_PNP
 324 #define CONFIG_EEPRO100
 325 #define CONFIG_SYS_RX_ETH_BUFFER        8               /* use 8 rx buffer on eepro100  */
 326 #endif
 327
 328 /*
 329  * Internal Definitions
 330  *
 331  * Boot Flags
 332  */
 333 #define BOOTFLAG_COLD           0x01    /* Normal Power-On: Boot from FLASH*/
 334 #define BOOTFLAG_WARM           0x02    /* Software reboot                 */
 335
 336
 337 /*-----------------------------------------------------------------------
 338  * Cache Configuration
 339  */
 340 #define CONFIG_SYS_CACHELINE_SIZE       32      /* For MPC8260 CPU              */
 341 #if defined(CONFIG_CMD_KGDB)
 342 #  define CONFIG_SYS_CACHELINE_SHIFT    5       /* log base 2 of the above value */
 343 #endif
 344
 345 /*-----------------------------------------------------------------------
 346  * HIDx - Hardware Implementation-dependent Registers                    2-11
 347  *-----------------------------------------------------------------------
 348  * HID0 also contains cache control - initially enable both caches and
 349  * invalidate contents, then the final state leaves only the instruction
 350  * cache enabled. Note that Power-On and Hard reset invalidate the caches,
 351  * but Soft reset does not.
 352  *
 353  * HID1 has only read-only information - nothing to set.
 354  */
 355 #define CONFIG_SYS_HID0_INIT    (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
 356                                 HID0_IFEM|HID0_ABE)
 357 #define CONFIG_SYS_HID0_FINAL   (HID0_ICE|HID0_IFEM|HID0_ABE)
 358 #define CONFIG_SYS_HID2 0
 359
 360 /*-----------------------------------------------------------------------
 361  * RMR - Reset Mode Register                                     5-5
 362  *-----------------------------------------------------------------------
 363  * turn on Checkstop Reset Enable
 364  */
 365 #define CONFIG_SYS_RMR          RMR_CSRE
 366
 367 /*-----------------------------------------------------------------------
 368  * BCR - Bus Configuration                                       4-25
 369  *-----------------------------------------------------------------------
 370  */
 371
 372 #define BCR_APD01       0x10000000
 373 #define CONFIG_SYS_BCR          (BCR_APD01|BCR_ETM|BCR_LETM)    /* 8260 mode */
 374
 375 /*-----------------------------------------------------------------------
 376  * SIUMCR - SIU Module Configuration                             4-31
 377  *-----------------------------------------------------------------------
 378  */
 379 #if 0
 380 #define CONFIG_SYS_SIUMCR       (SIUMCR_DPPC00|SIUMCR_APPC10|SIUMCR_CS10PC01)
 381 #else
 382 #define CONFIG_SYS_SIUMCR       (SIUMCR_DPPC10|SIUMCR_APPC10)
 383 #endif
 384
 385
 386 /*-----------------------------------------------------------------------
 387  * SYPCR - System Protection Control                             4-35
 388  * SYPCR can only be written once after reset!
 389  *-----------------------------------------------------------------------
 390  * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
 391  */
 392 #if defined(CONFIG_WATCHDOG)
 393 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
 394                          SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
 395 #else
 396 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
 397                          SYPCR_SWRI|SYPCR_SWP)
 398 #endif /* CONFIG_WATCHDOG */
 399
 400 /*-----------------------------------------------------------------------
 401  * TMCNTSC - Time Counter Status and Control                     4-40
 402  *-----------------------------------------------------------------------
 403  * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
 404  * and enable Time Counter
 405  */
 406 #define CONFIG_SYS_TMCNTSC      (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
 407
 408 /*-----------------------------------------------------------------------
 409  * PISCR - Periodic Interrupt Status and Control                 4-42
 410  *-----------------------------------------------------------------------
 411  * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
 412  * Periodic timer
 413  */
 414 #define CONFIG_SYS_PISCR        (PISCR_PS|PISCR_PTF|PISCR_PTE)
 415
 416 /*-----------------------------------------------------------------------
 417  * SCCR - System Clock Control                                   9-8
 418  *-----------------------------------------------------------------------
 419  */
 420 #define CONFIG_SYS_SCCR (SCCR_DFBRG00)
 421
 422 /*-----------------------------------------------------------------------
 423  * RCCR - RISC Controller Configuration                         13-7
 424  *-----------------------------------------------------------------------
 425  */
 426 #define CONFIG_SYS_RCCR 0
 427
 428 /*
 429  * Init Memory Controller:
 430  *
 431  * Bank Bus     Machine PortSz  Device
 432  * ---- ---     ------- ------  ------
 433  *  0   60x     GPCM    64 bit  FLASH
 434  *  1   60x     SDRAM   64 bit  SDRAM
 435  *
 436  */
 437
 438         /* Initialize SDRAM on local bus
 439          */
 440 #define CONFIG_SYS_INIT_LOCAL_SDRAM
 441
 442
 443 /* Minimum mask to separate preliminary
 444  * address ranges for CS[0:2]
 445  */
 446 #define CONFIG_SYS_MIN_AM_MASK 0xC0000000
 447
 448 /*
 449  * we use the same values for 32 MB and 128 MB SDRAM
 450  * refresh rate = 7.68 uS (100 MHz Bus Clock)
 451  */
 452 #define CONFIG_SYS_MPTPR        0x2000
 453 #define CONFIG_SYS_PSRT 0x16
 454
 455 #define CONFIG_SYS_MRS_OFFS     0x00000000
 456
 457
 458 #if defined(CONFIG_BOOT_ROM)
 459 /*
 460  * Bank 0 - Boot ROM (8 bit wide)
 461  */
 462 #define CONFIG_SYS_BR0_PRELIM   ((CONFIG_SYS_BOOTROM_BASE & BRx_BA_MSK)|\
 463                          BRx_PS_8                       |\
 464                          BRx_MS_GPCM_P                  |\
 465                          BRx_V)
 466
 467 #define CONFIG_SYS_OR0_PRELIM   (P2SZ_TO_AM(CONFIG_SYS_BOOTROM_SIZE)    |\
 468                          ORxG_CSNT                      |\
 469                          ORxG_ACS_DIV1                  |\
 470                          ORxG_SCY_5_CLK                 |\
 471                          ORxG_EHTR                      |\
 472                          ORxG_TRLX)
 473
 474 /*
 475  * Bank 1 - Flash (64 bit wide)
 476  */
 477 #define CONFIG_SYS_BR1_PRELIM   ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK)   |\
 478                          BRx_PS_64                      |\
 479                          BRx_MS_GPCM_P                  |\
 480                          BRx_V)
 481
 482 #define CONFIG_SYS_OR1_PRELIM   (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE)      |\
 483                          ORxG_CSNT                      |\
 484                          ORxG_ACS_DIV1                  |\
 485                          ORxG_SCY_5_CLK                 |\
 486                          ORxG_EHTR                      |\
 487                          ORxG_TRLX)
 488
 489 #else   /* ! CONFIG_BOOT_ROM */
 490
 491 /*
 492  * Bank 0 - Flash (64 bit wide)
 493  */
 494 #define CONFIG_SYS_BR0_PRELIM   ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK)   |\
 495                          BRx_PS_64                      |\
 496                          BRx_MS_GPCM_P                  |\
 497                          BRx_V)
 498
 499 #define CONFIG_SYS_OR0_PRELIM   (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE)      |\
 500                          ORxG_CSNT                      |\
 501                          ORxG_ACS_DIV1                  |\
 502                          ORxG_SCY_5_CLK                 |\
 503                          ORxG_EHTR                      |\
 504                          ORxG_TRLX)
 505
 506 /*
 507  * Bank 1 - Disk-On-Chip
 508  */
 509 #define CONFIG_SYS_BR1_PRELIM   ((CONFIG_SYS_DOC_BASE & BRx_BA_MSK)     |\
 510                          BRx_PS_8                       |\
 511                          BRx_MS_GPCM_P                  |\
 512                          BRx_V)
 513
 514 #define CONFIG_SYS_OR1_PRELIM   (P2SZ_TO_AM(CONFIG_SYS_DOC_SIZE)        |\
 515                          ORxG_CSNT                      |\
 516                          ORxG_ACS_DIV1                  |\
 517                          ORxG_SCY_5_CLK                 |\
 518                          ORxG_EHTR                      |\
 519                          ORxG_TRLX)
 520
 521 #endif /* CONFIG_BOOT_ROM */
 522
 523 /* Bank 2 - SDRAM
 524  */
 525
 526 #ifndef CONFIG_SYS_RAMBOOT
 527 #define CONFIG_SYS_BR2_PRELIM   ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK)   |\
 528                          BRx_PS_64                      |\
 529                          BRx_MS_SDRAM_P                 |\
 530                          BRx_V)
 531
 532         /* SDRAM initialization values for 8-column chips
 533          */
 534 #define CONFIG_SYS_OR2_8COL     (CONFIG_SYS_MIN_AM_MASK         |\
 535                          ORxS_BPD_4                     |\
 536                          ORxS_ROWST_PBI0_A9             |\
 537                          ORxS_NUMR_12)
 538
 539 #define CONFIG_SYS_PSDMR_8COL   (PSDMR_SDAM_A13_IS_A5           |\
 540                          PSDMR_BSMA_A14_A16             |\
 541                          PSDMR_SDA10_PBI0_A10           |\
 542                          PSDMR_RFRC_7_CLK               |\
 543                          PSDMR_PRETOACT_2W              |\
 544                          PSDMR_ACTTORW_2W               |\
 545                          PSDMR_LDOTOPRE_1C              |\
 546                          PSDMR_WRC_1C                   |\
 547                          PSDMR_CL_2)
 548
 549         /* SDRAM initialization values for 9-column chips
 550          */
 551 #define CONFIG_SYS_OR2_9COL     (CONFIG_SYS_MIN_AM_MASK         |\
 552                          ORxS_BPD_4                     |\
 553                          ORxS_ROWST_PBI0_A7             |\
 554                          ORxS_NUMR_13)
 555
 556 #define CONFIG_SYS_PSDMR_9COL   (PSDMR_SDAM_A14_IS_A5           |\
 557                          PSDMR_BSMA_A13_A15             |\
 558                          PSDMR_SDA10_PBI0_A9            |\
 559                          PSDMR_RFRC_7_CLK               |\
 560                          PSDMR_PRETOACT_2W              |\
 561                          PSDMR_ACTTORW_2W               |\
 562                          PSDMR_LDOTOPRE_1C              |\
 563                          PSDMR_WRC_1C                   |\
 564                          PSDMR_CL_2)
 565
 566 #define CONFIG_SYS_OR2_PRELIM    CONFIG_SYS_OR2_9COL
 567 #define CONFIG_SYS_PSDMR         CONFIG_SYS_PSDMR_9COL
 568
 569 #endif /* CONFIG_SYS_RAMBOOT */
 570
 571 #endif  /* __CONFIG_H */