include/configs/PM828.h

   1 /*
   2  * (C) Copyright 2001-2005
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * See file CREDITS for list of people who contributed to this
   6  * project.
   7  *
   8  * This program is free software; you can redistribute it and/or
   9  * modify it under the terms of the GNU General Public License as
  10  * published by the Free Software Foundation; either version 2 of
  11  * the License, or (at your option) any later version.
  12  *
  13  * This program is distributed in the hope that it will be useful,
  14  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  16  * GNU General Public License for more details.
  17  *
  18  * You should have received a copy of the GNU General Public License
  19  * along with this program; if not, write to the Free Software
  20  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  21  * MA 02111-1307 USA
  22  */
  23
  24 /*
  25  * board/config.h - configuration options, board specific
  26  */
  27
  28 #ifndef __CONFIG_H
  29 #define __CONFIG_H
  30
  31 #undef CONFIG_SYS_RAMBOOT
  32
  33 /*
  34  * High Level Configuration Options
  35  * (easy to change)
  36  */
  37
  38 #define CONFIG_MPC8260          1       /* This is a MPC8260 CPU        */
  39 #define CONFIG_PM828            1       /* ...on a PM828 module */
  40 #define CONFIG_CPM2             1       /* Has a CPM2 */
  41
  42 #undef CONFIG_DB_CR826_J30x_ON          /* J30x jumpers on D.B. carrier */
  43
  44 #define CONFIG_BOOTDELAY        5       /* autoboot after 5 seconds     */
  45
  46 #define CONFIG_PREBOOT  "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
  47
  48 #undef  CONFIG_BOOTARGS
  49 #define CONFIG_BOOTCOMMAND                                                      \
  50         "bootp;"                                                                \
  51         "setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "     \
  52         "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;"    \
  53         "bootm"
  54
  55 /* enable I2C and select the hardware/software driver */
  56 #undef  CONFIG_HARD_I2C
  57 #define CONFIG_SOFT_I2C         1       /* I2C bit-banged               */
  58 # define CONFIG_SYS_I2C_SPEED           50000
  59 # define CONFIG_SYS_I2C_SLAVE           0xFE
  60 /*
  61  * Software (bit-bang) I2C driver configuration
  62  */
  63 #define I2C_PORT        3               /* Port A=0, B=1, C=2, D=3 */
  64 #define I2C_ACTIVE      (iop->pdir |=  0x00010000)
  65 #define I2C_TRISTATE    (iop->pdir &= ~0x00010000)
  66 #define I2C_READ        ((iop->pdat & 0x00010000) != 0)
  67 #define I2C_SDA(bit)    if(bit) iop->pdat |=  0x00010000; \
  68                         else    iop->pdat &= ~0x00010000
  69 #define I2C_SCL(bit)    if(bit) iop->pdat |=  0x00020000; \
  70                         else    iop->pdat &= ~0x00020000
  71 #define I2C_DELAY       udelay(5)       /* 1/4 I2C clock duration */
  72
  73
  74 #define CONFIG_RTC_PCF8563
  75 #define CONFIG_SYS_I2C_RTC_ADDR 0x51
  76
  77 /*
  78  * select serial console configuration
  79  *
  80  * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
  81  * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
  82  * for SCC).
  83  *
  84  * if CONFIG_CONS_NONE is defined, then the serial console routines must
  85  * defined elsewhere (for example, on the cogent platform, there are serial
  86  * ports on the motherboard which are used for the serial console - see
  87  * cogent/cma101/serial.[ch]).
  88  */
  89 #define CONFIG_CONS_ON_SMC              /* define if console on SMC */
  90 #undef  CONFIG_CONS_ON_SCC              /* define if console on SCC */
  91 #undef  CONFIG_CONS_NONE                /* define if console on something else*/
  92 #define CONFIG_CONS_INDEX       2       /* which serial channel for console */
  93
  94 /*
  95  * select ethernet configuration
  96  *
  97  * if CONFIG_ETHER_ON_SCC is selected, then
  98  *   - CONFIG_ETHER_INDEX must be set to the channel number (1-4)
  99  *   - CONFIG_NET_MULTI must not be defined
 100  *
 101  * if CONFIG_ETHER_ON_FCC is selected, then
 102  *   - one or more CONFIG_ETHER_ON_FCCx (x=1,2,3) must also be selected
 103  *   - CONFIG_NET_MULTI must be defined
 104  *
 105  * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
 106  * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
 107  */
 108 #define CONFIG_NET_MULTI
 109 #undef  CONFIG_ETHER_NONE               /* define if ether on something else */
 110
 111 #undef  CONFIG_ETHER_ON_SCC             /* define if ether on SCC       */
 112 #define CONFIG_ETHER_INDEX    1         /* which SCC channel for ethernet */
 113
 114 #define CONFIG_ETHER_ON_FCC             /* define if ether on FCC       */
 115 /*
 116  * - Rx-CLK is CLK11
 117  * - Tx-CLK is CLK10
 118  */
 119 #define CONFIG_ETHER_ON_FCC1
 120 # define CONFIG_SYS_CMXFCR_MASK1        (CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
 121 #ifndef CONFIG_DB_CR826_J30x_ON
 122 # define CONFIG_SYS_CMXFCR_VALUE1       (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK10)
 123 #else
 124 # define CONFIG_SYS_CMXFCR_VALUE1       (CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12)
 125 #endif
 126 /*
 127  * - Rx-CLK is CLK15
 128  * - Tx-CLK is CLK14
 129  */
 130 #define CONFIG_ETHER_ON_FCC2
 131 # define CONFIG_SYS_CMXFCR_MASK2        (CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
 132 # define CONFIG_SYS_CMXFCR_VALUE2       (CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
 133 /*
 134  * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
 135  * - Enable Full Duplex in FSMR
 136  */
 137 # define CONFIG_SYS_CPMFCR_RAMTYPE      0
 138 # define CONFIG_SYS_FCC_PSMR            (FCC_PSMR_FDE|FCC_PSMR_LPB)
 139
 140 /* system clock rate (CLKIN) - equal to the 60x and local bus speed */
 141 #define CONFIG_8260_CLKIN       100000000       /* in Hz */
 142
 143 #if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
 144 #define CONFIG_BAUDRATE         230400
 145 #else
 146 #define CONFIG_BAUDRATE         9600
 147 #endif
 148
 149 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download  */
 150 #undef  CONFIG_SYS_LOADS_BAUD_CHANGE            /* don't allow baudrate change  */
 151
 152 #undef  CONFIG_WATCHDOG                 /* watchdog disabled            */
 153
 154 /*
 155  * BOOTP options
 156  */
 157 #define CONFIG_BOOTP_SUBNETMASK
 158 #define CONFIG_BOOTP_GATEWAY
 159 #define CONFIG_BOOTP_HOSTNAME
 160 #define CONFIG_BOOTP_BOOTPATH
 161 #define CONFIG_BOOTP_BOOTFILESIZE
 162
 163
 164 /*
 165  * Command line configuration.
 166  */
 167 #include <config_cmd_default.h>
 168
 169 #define CONFIG_CMD_BEDBUG
 170 #define CONFIG_CMD_DATE
 171 #define CONFIG_CMD_DHCP
 172 #define CONFIG_CMD_EEPROM
 173 #define CONFIG_CMD_I2C
 174 #define CONFIG_CMD_NFS
 175 #define CONFIG_CMD_SNTP
 176
 177 #ifdef CONFIG_PCI
 178 #define CONFIG_CMD_PCI
 179 #endif
 180
 181 /*
 182  * Miscellaneous configurable options
 183  */
 184 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
 185 #define CONFIG_SYS_PROMPT       "=> "           /* Monitor Command Prompt       */
 186 #if defined(CONFIG_CMD_KGDB)
 187 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size      */
 188 #else
 189 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size      */
 190 #endif
 191 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 192 #define CONFIG_SYS_MAXARGS      16              /* max number of command args   */
 193 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 194
 195 #define CONFIG_SYS_MEMTEST_START        0x0400000       /* memtest works on     */
 196 #define CONFIG_SYS_MEMTEST_END 0x0C00000        /* 4 ... 12 MB in DRAM  */
 197
 198 #define CONFIG_SYS_LOAD_ADDR    0x100000        /* default load address */
 199
 200 #define CONFIG_SYS_HZ           1000            /* decrementer freq: 1 ms ticks */
 201
 202 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
 203
 204 #define CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC     /* "bad" address                */
 205
 206 /*
 207  * For booting Linux, the board info and command line data
 208  * have to be in the first 8 MB of memory, since this is
 209  * the maximum mapped by the Linux kernel during initialization.
 210  */
 211 #define CONFIG_SYS_BOOTMAPSZ         (8 << 20)       /* Initial Memory map for Linux */
 212
 213 /*-----------------------------------------------------------------------
 214  * Flash and Boot ROM mapping
 215  */
 216
 217 #define CONFIG_SYS_BOOTROM_BASE 0xFF800000
 218 #define CONFIG_SYS_BOOTROM_SIZE 0x00080000
 219 #define CONFIG_SYS_FLASH0_BASE          0x40000000
 220 #define CONFIG_SYS_FLASH0_SIZE          0x02000000
 221 #define CONFIG_SYS_DOC_BASE             0xFF800000
 222 #define CONFIG_SYS_DOC_SIZE             0x00100000
 223
 224
 225 /* Flash bank size (for preliminary settings)
 226  */
 227 #define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE
 228
 229 /*-----------------------------------------------------------------------
 230  * FLASH organization
 231  */
 232 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max num of memory banks      */
 233 #define CONFIG_SYS_MAX_FLASH_SECT       135     /* max num of sects on one chip */
 234
 235 #define CONFIG_SYS_FLASH_ERASE_TOUT     240000  /* Flash Erase Timeout (in ms)  */
 236 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (in ms)  */
 237
 238 #if 0
 239 /* Start port with environment in flash; switch to EEPROM later */
 240 #define CONFIG_ENV_IS_IN_FLASH  1
 241 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE+0x40000)
 242 #define CONFIG_ENV_SIZE         0x40000
 243 #define CONFIG_ENV_SECT_SIZE    0x40000
 244 #else
 245 /* Final version: environment in EEPROM */
 246 #define CONFIG_ENV_IS_IN_EEPROM 1
 247 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x58
 248 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
 249 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       4
 250 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* and takes up to 10 msec */
 251 #define CONFIG_ENV_OFFSET               512
 252 #define CONFIG_ENV_SIZE         (2048 - 512)
 253 #endif
 254
 255 /*-----------------------------------------------------------------------
 256  * Hard Reset Configuration Words
 257  *
 258  * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
 259  * defines for the various registers affected by the HRCW e.g. changing
 260  * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
 261  */
 262 #if defined(CONFIG_BOOT_ROM)
 263 #define CONFIG_SYS_HRCW_MASTER          (HRCW_BPS01 | HRCW_CIP | HRCW_ISB100 | HRCW_BMS)
 264 #else
 265 #define CONFIG_SYS_HRCW_MASTER          (HRCW_CIP | HRCW_ISB100 | HRCW_BMS)
 266 #endif
 267
 268 /* no slaves so just fill with zeros */
 269 #define CONFIG_SYS_HRCW_SLAVE1          0
 270 #define CONFIG_SYS_HRCW_SLAVE2          0
 271 #define CONFIG_SYS_HRCW_SLAVE3          0
 272 #define CONFIG_SYS_HRCW_SLAVE4          0
 273 #define CONFIG_SYS_HRCW_SLAVE5          0
 274 #define CONFIG_SYS_HRCW_SLAVE6          0
 275 #define CONFIG_SYS_HRCW_SLAVE7          0
 276
 277 /*-----------------------------------------------------------------------
 278  * Internal Memory Mapped Register
 279  */
 280 #define CONFIG_SYS_IMMR         0xF0000000
 281
 282 /*-----------------------------------------------------------------------
 283  * Definitions for initial stack pointer and data area (in DPRAM)
 284  */
 285 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_IMMR
 286 #define CONFIG_SYS_INIT_RAM_END 0x4000  /* End of used area in DPRAM    */
 287 #define CONFIG_SYS_GBL_DATA_SIZE        128 /* size in bytes reserved for initial data*/
 288 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 289 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 290
 291 /*-----------------------------------------------------------------------
 292  * Start addresses for the final memory configuration
 293  * (Set up by the startup code)
 294  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 295  *
 296  * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE, local SDRAM
 297  * is mapped at SDRAM_BASE2_PRELIM.
 298  */
 299 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 300 #define CONFIG_SYS_FLASH_BASE           CONFIG_SYS_FLASH0_BASE
 301 #define CONFIG_SYS_MONITOR_BASE TEXT_BASE
 302 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for Monitor */
 303 #define CONFIG_SYS_MALLOC_LEN           (128 << 10)     /* Reserve 128 kB for malloc()*/
 304
 305 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 306 # define CONFIG_SYS_RAMBOOT
 307 #endif
 308
 309 #ifdef  CONFIG_PCI
 310 #define CONFIG_PCI_PNP
 311 #define CONFIG_EEPRO100
 312 #define CONFIG_SYS_RX_ETH_BUFFER        8               /* use 8 rx buffer on eepro100  */
 313 #endif
 314
 315 /*
 316  * Internal Definitions
 317  *
 318  * Boot Flags
 319  */
 320 #define BOOTFLAG_COLD           0x01    /* Normal Power-On: Boot from FLASH*/
 321 #define BOOTFLAG_WARM           0x02    /* Software reboot                 */
 322
 323
 324 /*-----------------------------------------------------------------------
 325  * Cache Configuration
 326  */
 327 #define CONFIG_SYS_CACHELINE_SIZE       32      /* For MPC8260 CPU              */
 328 #if defined(CONFIG_CMD_KGDB)
 329 #  define CONFIG_SYS_CACHELINE_SHIFT    5       /* log base 2 of the above value */
 330 #endif
 331
 332 /*-----------------------------------------------------------------------
 333  * HIDx - Hardware Implementation-dependent Registers                    2-11
 334  *-----------------------------------------------------------------------
 335  * HID0 also contains cache control - initially enable both caches and
 336  * invalidate contents, then the final state leaves only the instruction
 337  * cache enabled. Note that Power-On and Hard reset invalidate the caches,
 338  * but Soft reset does not.
 339  *
 340  * HID1 has only read-only information - nothing to set.
 341  */
 342 #define CONFIG_SYS_HID0_INIT    (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
 343                                 HID0_IFEM|HID0_ABE)
 344 #define CONFIG_SYS_HID0_FINAL   (HID0_ICE|HID0_IFEM|HID0_ABE)
 345 #define CONFIG_SYS_HID2 0
 346
 347 /*-----------------------------------------------------------------------
 348  * RMR - Reset Mode Register                                     5-5
 349  *-----------------------------------------------------------------------
 350  * turn on Checkstop Reset Enable
 351  */
 352 #define CONFIG_SYS_RMR          RMR_CSRE
 353
 354 /*-----------------------------------------------------------------------
 355  * BCR - Bus Configuration                                       4-25
 356  *-----------------------------------------------------------------------
 357  */
 358
 359 #define BCR_APD01       0x10000000
 360 #define CONFIG_SYS_BCR          (BCR_APD01|BCR_ETM|BCR_LETM)    /* 8260 mode */
 361
 362 /*-----------------------------------------------------------------------
 363  * SIUMCR - SIU Module Configuration                             4-31
 364  *-----------------------------------------------------------------------
 365  */
 366 #if 0
 367 #define CONFIG_SYS_SIUMCR       (SIUMCR_DPPC00|SIUMCR_APPC10|SIUMCR_CS10PC01)
 368 #else
 369 #define CONFIG_SYS_SIUMCR       (SIUMCR_DPPC10|SIUMCR_APPC10)
 370 #endif
 371
 372
 373 /*-----------------------------------------------------------------------
 374  * SYPCR - System Protection Control                             4-35
 375  * SYPCR can only be written once after reset!
 376  *-----------------------------------------------------------------------
 377  * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
 378  */
 379 #if defined(CONFIG_WATCHDOG)
 380 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
 381                          SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
 382 #else
 383 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
 384                          SYPCR_SWRI|SYPCR_SWP)
 385 #endif /* CONFIG_WATCHDOG */
 386
 387 /*-----------------------------------------------------------------------
 388  * TMCNTSC - Time Counter Status and Control                     4-40
 389  *-----------------------------------------------------------------------
 390  * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
 391  * and enable Time Counter
 392  */
 393 #define CONFIG_SYS_TMCNTSC      (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
 394
 395 /*-----------------------------------------------------------------------
 396  * PISCR - Periodic Interrupt Status and Control                 4-42
 397  *-----------------------------------------------------------------------
 398  * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
 399  * Periodic timer
 400  */
 401 #define CONFIG_SYS_PISCR        (PISCR_PS|PISCR_PTF|PISCR_PTE)
 402
 403 /*-----------------------------------------------------------------------
 404  * SCCR - System Clock Control                                   9-8
 405  *-----------------------------------------------------------------------
 406  */
 407 #define CONFIG_SYS_SCCR (SCCR_DFBRG00)
 408
 409 /*-----------------------------------------------------------------------
 410  * RCCR - RISC Controller Configuration                         13-7
 411  *-----------------------------------------------------------------------
 412  */
 413 #define CONFIG_SYS_RCCR 0
 414
 415 /*
 416  * Init Memory Controller:
 417  *
 418  * Bank Bus     Machine PortSz  Device
 419  * ---- ---     ------- ------  ------
 420  *  0   60x     GPCM    64 bit  FLASH
 421  *  1   60x     SDRAM   64 bit  SDRAM
 422  *
 423  */
 424
 425         /* Initialize SDRAM on local bus
 426          */
 427 #define CONFIG_SYS_INIT_LOCAL_SDRAM
 428
 429
 430 /* Minimum mask to separate preliminary
 431  * address ranges for CS[0:2]
 432  */
 433 #define CONFIG_SYS_MIN_AM_MASK 0xC0000000
 434
 435 /*
 436  * we use the same values for 32 MB and 128 MB SDRAM
 437  * refresh rate = 7.68 uS (100 MHz Bus Clock)
 438  */
 439 #define CONFIG_SYS_MPTPR        0x2000
 440 #define CONFIG_SYS_PSRT 0x16
 441
 442 #define CONFIG_SYS_MRS_OFFS     0x00000000
 443
 444
 445 #if defined(CONFIG_BOOT_ROM)
 446 /*
 447  * Bank 0 - Boot ROM (8 bit wide)
 448  */
 449 #define CONFIG_SYS_BR0_PRELIM   ((CONFIG_SYS_BOOTROM_BASE & BRx_BA_MSK)|\
 450                          BRx_PS_8                       |\
 451                          BRx_MS_GPCM_P                  |\
 452                          BRx_V)
 453
 454 #define CONFIG_SYS_OR0_PRELIM   (P2SZ_TO_AM(CONFIG_SYS_BOOTROM_SIZE)    |\
 455                          ORxG_CSNT                      |\
 456                          ORxG_ACS_DIV1                  |\
 457                          ORxG_SCY_5_CLK                 |\
 458                          ORxG_EHTR                      |\
 459                          ORxG_TRLX)
 460
 461 /*
 462  * Bank 1 - Flash (64 bit wide)
 463  */
 464 #define CONFIG_SYS_BR1_PRELIM   ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK)   |\
 465                          BRx_PS_64                      |\
 466                          BRx_MS_GPCM_P                  |\
 467                          BRx_V)
 468
 469 #define CONFIG_SYS_OR1_PRELIM   (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE)      |\
 470                          ORxG_CSNT                      |\
 471                          ORxG_ACS_DIV1                  |\
 472                          ORxG_SCY_5_CLK                 |\
 473                          ORxG_EHTR                      |\
 474                          ORxG_TRLX)
 475
 476 #else   /* ! CONFIG_BOOT_ROM */
 477
 478 /*
 479  * Bank 0 - Flash (64 bit wide)
 480  */
 481 #define CONFIG_SYS_BR0_PRELIM   ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK)   |\
 482                          BRx_PS_64                      |\
 483                          BRx_MS_GPCM_P                  |\
 484                          BRx_V)
 485
 486 #define CONFIG_SYS_OR0_PRELIM   (P2SZ_TO_AM(CONFIG_SYS_FLASH_SIZE)      |\
 487                          ORxG_CSNT                      |\
 488                          ORxG_ACS_DIV1                  |\
 489                          ORxG_SCY_5_CLK                 |\
 490                          ORxG_EHTR                      |\
 491                          ORxG_TRLX)
 492
 493 /*
 494  * Bank 1 - Disk-On-Chip
 495  */
 496 #define CONFIG_SYS_BR1_PRELIM   ((CONFIG_SYS_DOC_BASE & BRx_BA_MSK)     |\
 497                          BRx_PS_8                       |\
 498                          BRx_MS_GPCM_P                  |\
 499                          BRx_V)
 500
 501 #define CONFIG_SYS_OR1_PRELIM   (P2SZ_TO_AM(CONFIG_SYS_DOC_SIZE)        |\
 502                          ORxG_CSNT                      |\
 503                          ORxG_ACS_DIV1                  |\
 504                          ORxG_SCY_5_CLK                 |\
 505                          ORxG_EHTR                      |\
 506                          ORxG_TRLX)
 507
 508 #endif /* CONFIG_BOOT_ROM */
 509
 510 /* Bank 2 - SDRAM
 511  */
 512
 513 #ifndef CONFIG_SYS_RAMBOOT
 514 #define CONFIG_SYS_BR2_PRELIM   ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK)   |\
 515                          BRx_PS_64                      |\
 516                          BRx_MS_SDRAM_P                 |\
 517                          BRx_V)
 518
 519         /* SDRAM initialization values for 8-column chips
 520          */
 521 #define CONFIG_SYS_OR2_8COL     (CONFIG_SYS_MIN_AM_MASK         |\
 522                          ORxS_BPD_4                     |\
 523                          ORxS_ROWST_PBI0_A9             |\
 524                          ORxS_NUMR_12)
 525
 526 #define CONFIG_SYS_PSDMR_8COL   (PSDMR_SDAM_A13_IS_A5           |\
 527                          PSDMR_BSMA_A14_A16             |\
 528                          PSDMR_SDA10_PBI0_A10           |\
 529                          PSDMR_RFRC_7_CLK               |\
 530                          PSDMR_PRETOACT_2W              |\
 531                          PSDMR_ACTTORW_2W               |\
 532                          PSDMR_LDOTOPRE_1C              |\
 533                          PSDMR_WRC_1C                   |\
 534                          PSDMR_CL_2)
 535
 536         /* SDRAM initialization values for 9-column chips
 537          */
 538 #define CONFIG_SYS_OR2_9COL     (CONFIG_SYS_MIN_AM_MASK         |\
 539                          ORxS_BPD_4                     |\
 540                          ORxS_ROWST_PBI0_A7             |\
 541                          ORxS_NUMR_13)
 542
 543 #define CONFIG_SYS_PSDMR_9COL   (PSDMR_SDAM_A14_IS_A5           |\
 544                          PSDMR_BSMA_A13_A15             |\
 545                          PSDMR_SDA10_PBI0_A9            |\
 546                          PSDMR_RFRC_7_CLK               |\
 547                          PSDMR_PRETOACT_2W              |\
 548                          PSDMR_ACTTORW_2W               |\
 549                          PSDMR_LDOTOPRE_1C              |\
 550                          PSDMR_WRC_1C                   |\
 551                          PSDMR_CL_2)
 552
 553 #define CONFIG_SYS_OR2_PRELIM    CONFIG_SYS_OR2_9COL
 554 #define CONFIG_SYS_PSDMR         CONFIG_SYS_PSDMR_9COL
 555
 556 #endif /* CONFIG_SYS_RAMBOOT */
 557
 558 #endif  /* __CONFIG_H */