include/configs/TQM866M.h

   1 /*
   2  * (C) Copyright 2000-2008
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * board/config.h - configuration options, board specific
  10  */
  11
  12 #ifndef __CONFIG_H
  13 #define __CONFIG_H
  14
  15 /*
  16  * High Level Configuration Options
  17  * (easy to change)
  18  */
  19
  20 #define CONFIG_MPC866           1       /* This is a MPC866 CPU         */
  21 #define CONFIG_TQM866M          1       /* ...on a TQM8xxM module       */
  22
  23 #define CONFIG_SYS_TEXT_BASE    0x40000000
  24
  25 #define CONFIG_8xx_OSCLK                10000000        /*  10 MHz - PLL input clock    */
  26 #define CONFIG_SYS_8xx_CPUCLK_MIN               15000000        /*  15 MHz - CPU minimum clock  */
  27 #define CONFIG_SYS_8xx_CPUCLK_MAX               133000000       /* 133 MHz - CPU maximum clock  */
  28 #define CONFIG_8xx_CPUCLK_DEFAULT       50000000        /*  50 MHz - CPU default clock  */
  29                                                 /* (it will be used if there is no      */
  30                                                 /* 'cpuclk' variable with valid value)  */
  31
  32 #undef CONFIG_SYS_MEASURE_CPUCLK                        /* Measure real cpu clock       */
  33                                                 /* (function measure_gclk()     */
  34                                                 /* will be called)              */
  35 #ifdef CONFIG_SYS_MEASURE_CPUCLK
  36 #define CONFIG_SYS_8XX_XIN              10000000        /* measure_gclk() needs this    */
  37 #endif
  38
  39 #define CONFIG_8xx_CONS_SMC1    1       /* Console is on SMC1           */
  40 #define CONFIG_SYS_SMC_RXBUFLEN 128
  41 #define CONFIG_SYS_MAXIDLE      10
  42 #define CONFIG_BAUDRATE         115200  /* console baudrate = 115kbps   */
  43
  44 #define CONFIG_BOOTCOUNT_LIMIT
  45
  46 #define CONFIG_BOOTDELAY        5       /* autoboot after 5 seconds     */
  47
  48 #define CONFIG_BOARD_TYPES      1       /* support board types          */
  49
  50 #define CONFIG_PREBOOT  "echo;" \
  51         "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
  52         "echo"
  53
  54 #undef  CONFIG_BOOTARGS
  55
  56 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
  57         "netdev=eth0\0"                                                 \
  58         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
  59                 "nfsroot=${serverip}:${rootpath}\0"                     \
  60         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
  61         "addip=setenv bootargs ${bootargs} "                            \
  62                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
  63                 ":${hostname}:${netdev}:off panic=1\0"                  \
  64         "flash_nfs=run nfsargs addip;"                                  \
  65                 "bootm ${kernel_addr}\0"                                \
  66         "flash_self=run ramargs addip;"                                 \
  67                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
  68         "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"     \
  69         "rootpath=/opt/eldk/ppc_8xx\0"                                  \
  70         "hostname=TQM866M\0"                                            \
  71         "bootfile=TQM866M/uImage\0"                                     \
  72         "fdt_addr=400C0000\0"                                           \
  73         "kernel_addr=40100000\0"                                        \
  74         "ramdisk_addr=40280000\0"                                       \
  75         "u-boot=TQM866M/u-image.bin\0"                                  \
  76         "load=tftp 200000 ${u-boot}\0"                                  \
  77         "update=prot off 40000000 +${filesize};"                        \
  78                 "era 40000000 +${filesize};"                            \
  79                 "cp.b 200000 40000000 ${filesize};"                     \
  80                 "sete filesize;save\0"                                  \
  81         ""
  82 #define CONFIG_BOOTCOMMAND      "run flash_self"
  83
  84 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download  */
  85 #undef  CONFIG_SYS_LOADS_BAUD_CHANGE            /* don't allow baudrate change  */
  86
  87 #undef  CONFIG_WATCHDOG                 /* watchdog disabled            */
  88
  89 #define CONFIG_STATUS_LED       1       /* Status LED enabled           */
  90
  91 #undef  CONFIG_CAN_DRIVER               /* CAN Driver support disabled  */
  92
  93 /* enable I2C and select the hardware/software driver */
  94 #undef  CONFIG_HARD_I2C                 /* I2C with hardware support    */
  95 #define CONFIG_SOFT_I2C         1       /* I2C bit-banged               */
  96
  97 #define CONFIG_SYS_I2C_SPEED            93000   /* 93 kHz is supposed to work   */
  98 #define CONFIG_SYS_I2C_SLAVE            0xFE
  99
 100 #ifdef CONFIG_SOFT_I2C
 101 /*
 102  * Software (bit-bang) I2C driver configuration
 103  */
 104 #define PB_SCL          0x00000020      /* PB 26 */
 105 #define PB_SDA          0x00000010      /* PB 27 */
 106
 107 #define I2C_INIT        (immr->im_cpm.cp_pbdir |=  PB_SCL)
 108 #define I2C_ACTIVE      (immr->im_cpm.cp_pbdir |=  PB_SDA)
 109 #define I2C_TRISTATE    (immr->im_cpm.cp_pbdir &= ~PB_SDA)
 110 #define I2C_READ        ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
 111 #define I2C_SDA(bit)    if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
 112                         else    immr->im_cpm.cp_pbdat &= ~PB_SDA
 113 #define I2C_SCL(bit)    if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 114                         else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 115 #define I2C_DELAY       udelay(2)       /* 1/4 I2C clock duration */
 116 #endif  /* CONFIG_SOFT_I2C */
 117
 118 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50            /* EEPROM AT24C256      */
 119 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2                /* two byte address     */
 120 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       4
 121 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* and takes up to 10 msec */
 122
 123 /*
 124  * BOOTP options
 125  */
 126 #define CONFIG_BOOTP_SUBNETMASK
 127 #define CONFIG_BOOTP_GATEWAY
 128 #define CONFIG_BOOTP_HOSTNAME
 129 #define CONFIG_BOOTP_BOOTPATH
 130 #define CONFIG_BOOTP_BOOTFILESIZE
 131
 132
 133 #define CONFIG_MAC_PARTITION
 134 #define CONFIG_DOS_PARTITION
 135
 136 #undef CONFIG_RTC_MPC8xx                /* MPC866 does not support RTC  */
 137
 138 #define CONFIG_TIMESTAMP                /* but print image timestmps    */
 139
 140
 141 /*
 142  * Command line configuration.
 143  */
 144 #include <config_cmd_default.h>
 145
 146 #define CONFIG_CMD_ASKENV
 147 #define CONFIG_CMD_DHCP
 148 #define CONFIG_CMD_EEPROM
 149 #define CONFIG_CMD_ELF
 150 #define CONFIG_CMD_EXT2
 151 #define CONFIG_CMD_IDE
 152 #define CONFIG_CMD_JFFS2
 153 #define CONFIG_CMD_NFS
 154 #define CONFIG_CMD_SNTP
 155
 156
 157 #define CONFIG_NETCONSOLE
 158
 159
 160 /*
 161  * Miscellaneous configurable options
 162  */
 163 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
 164 #define CONFIG_SYS_PROMPT               "=> "   /* Monitor Command Prompt       */
 165
 166 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 167 #define CONFIG_SYS_HUSH_PARSER          1       /* Use the HUSH parser          */
 168
 169 #if defined(CONFIG_CMD_KGDB)
 170 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size      */
 171 #else
 172 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size      */
 173 #endif
 174 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 175 #define CONFIG_SYS_MAXARGS              16      /* max number of command args   */
 176 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 177
 178 #define CONFIG_SYS_MEMTEST_START        0x0400000       /* memtest works on     */
 179 #define CONFIG_SYS_MEMTEST_END          0x0C00000       /* 4 ... 12 MB in DRAM  */
 180
 181 #define CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */
 182
 183 #define CONFIG_SYS_HZ                   1000    /* decrementer freq: 1 ms ticks */
 184
 185 /*
 186  * Low Level Configuration Settings
 187  * (address mappings, register initial values, etc.)
 188  * You should know what you are doing if you make changes here.
 189  */
 190 /*-----------------------------------------------------------------------
 191  * Internal Memory Mapped Register
 192  */
 193 #define CONFIG_SYS_IMMR         0xFFF00000
 194
 195 /*-----------------------------------------------------------------------
 196  * Definitions for initial stack pointer and data area (in DPRAM)
 197  */
 198 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_IMMR
 199 #define CONFIG_SYS_INIT_RAM_SIZE        0x2F00  /* Size of used area in DPRAM   */
 200 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 201 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 202
 203 /*-----------------------------------------------------------------------
 204  * Start addresses for the final memory configuration
 205  * (Set up by the startup code)
 206  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 207  */
 208 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 209 #define CONFIG_SYS_FLASH_BASE           0x40000000
 210 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for Monitor   */
 211 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
 212 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)     /* Reserve 256 kB for malloc()  */
 213
 214 /*
 215  * For booting Linux, the board info and command line data
 216  * have to be in the first 8 MB of memory, since this is
 217  * the maximum mapped by the Linux kernel during initialization.
 218  */
 219 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 220
 221 /*-----------------------------------------------------------------------
 222  * FLASH organization
 223  */
 224 /* use CFI flash driver */
 225 #define CONFIG_SYS_FLASH_CFI            1       /* Flash is CFI conformant */
 226 #define CONFIG_FLASH_CFI_DRIVER 1       /* Use the common driver */
 227 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE }
 228 #define CONFIG_SYS_FLASH_EMPTY_INFO
 229 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE       1
 230 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max number of memory banks */
 231 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max number of sectors on one chip */
 232
 233 #define CONFIG_ENV_IS_IN_FLASH  1
 234 #define CONFIG_ENV_OFFSET               0x40000 /*   Offset   of Environment Sector     */
 235 #define CONFIG_ENV_SIZE         0x08000 /* Total Size of Environment Sector     */
 236 #define CONFIG_ENV_SECT_SIZE    0x40000 /* Total Size of Environment Sector     */
 237
 238 /* Address and size of Redundant Environment Sector     */
 239 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
 240 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 241
 242 #define CONFIG_SYS_USE_PPCENV                   /* Environment embedded in sect .ppcenv */
 243
 244 #define CONFIG_MISC_INIT_R              /* Make sure to remap flashes correctly */
 245
 246 /*-----------------------------------------------------------------------
 247  * Dynamic MTD partition support
 248  */
 249 #define CONFIG_CMD_MTDPARTS
 250 #define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
 251 #define CONFIG_FLASH_CFI_MTD
 252 #define MTDIDS_DEFAULT          "nor0=TQM8xxM-0"
 253
 254 #define MTDPARTS_DEFAULT        "mtdparts=TQM8xxM-0:512k(u-boot),"      \
 255                                                 "128k(dtb),"            \
 256                                                 "1920k(kernel),"        \
 257                                                 "5632(rootfs),"         \
 258                                                 "4m(data)"
 259
 260 /*-----------------------------------------------------------------------
 261  * Hardware Information Block
 262  */
 263 #define CONFIG_SYS_HWINFO_OFFSET        0x0003FFC0      /* offset of HW Info block */
 264 #define CONFIG_SYS_HWINFO_SIZE          0x00000040      /* size   of HW Info block */
 265 #define CONFIG_SYS_HWINFO_MAGIC 0x54514D38      /* 'TQM8' */
 266
 267 /*-----------------------------------------------------------------------
 268  * Cache Configuration
 269  */
 270 #define CONFIG_SYS_CACHELINE_SIZE       16      /* For all MPC8xx CPUs                  */
 271 #if defined(CONFIG_CMD_KGDB)
 272 #define CONFIG_SYS_CACHELINE_SHIFT      4       /* log base 2 of the above value        */
 273 #endif
 274
 275 /*-----------------------------------------------------------------------
 276  * SYPCR - System Protection Control                            11-9
 277  * SYPCR can only be written once after reset!
 278  *-----------------------------------------------------------------------
 279  * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
 280  */
 281 #if defined(CONFIG_WATCHDOG)
 282 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
 283                          SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
 284 #else
 285 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
 286 #endif
 287
 288 /*-----------------------------------------------------------------------
 289  * SIUMCR - SIU Module Configuration                            11-6
 290  *-----------------------------------------------------------------------
 291  * PCMCIA config., multi-function pin tri-state
 292  */
 293 #ifndef CONFIG_CAN_DRIVER
 294 #define CONFIG_SYS_SIUMCR       (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
 295 #else   /* we must activate GPL5 in the SIUMCR for CAN */
 296 #define CONFIG_SYS_SIUMCR       (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
 297 #endif  /* CONFIG_CAN_DRIVER */
 298
 299 /*-----------------------------------------------------------------------
 300  * TBSCR - Time Base Status and Control                         11-26
 301  *-----------------------------------------------------------------------
 302  * Clear Reference Interrupt Status, Timebase freezing enabled
 303  */
 304 #define CONFIG_SYS_TBSCR        (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
 305
 306 /*-----------------------------------------------------------------------
 307  * PISCR - Periodic Interrupt Status and Control                11-31
 308  *-----------------------------------------------------------------------
 309  * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
 310  */
 311 #define CONFIG_SYS_PISCR        (PISCR_PS | PISCR_PITF)
 312
 313 /*-----------------------------------------------------------------------
 314  * SCCR - System Clock and reset Control Register               15-27
 315  *-----------------------------------------------------------------------
 316  * Set clock output, timebase and RTC source and divider,
 317  * power management and some other internal clocks
 318  */
 319 #define SCCR_MASK       SCCR_EBDF11
 320 #define CONFIG_SYS_SCCR (SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 321                          SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 322                          SCCR_DFALCD00)
 323
 324 /*-----------------------------------------------------------------------
 325  * PCMCIA stuff
 326  *-----------------------------------------------------------------------
 327  *
 328  */
 329 #define CONFIG_SYS_PCMCIA_MEM_ADDR      (0xE0000000)
 330 #define CONFIG_SYS_PCMCIA_MEM_SIZE      ( 64 << 20 )
 331 #define CONFIG_SYS_PCMCIA_DMA_ADDR      (0xE4000000)
 332 #define CONFIG_SYS_PCMCIA_DMA_SIZE      ( 64 << 20 )
 333 #define CONFIG_SYS_PCMCIA_ATTRB_ADDR    (0xE8000000)
 334 #define CONFIG_SYS_PCMCIA_ATTRB_SIZE    ( 64 << 20 )
 335 #define CONFIG_SYS_PCMCIA_IO_ADDR       (0xEC000000)
 336 #define CONFIG_SYS_PCMCIA_IO_SIZE       ( 64 << 20 )
 337
 338 /*-----------------------------------------------------------------------
 339  * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
 340  *-----------------------------------------------------------------------
 341  */
 342
 343 #define CONFIG_IDE_PREINIT      1       /* Use preinit IDE hook */
 344 #define CONFIG_IDE_8xx_PCCARD   1       /* Use IDE with PC Card Adapter */
 345
 346 #undef  CONFIG_IDE_8xx_DIRECT           /* Direct IDE    not supported  */
 347 #undef  CONFIG_IDE_LED                  /* LED   for ide not supported  */
 348 #undef  CONFIG_IDE_RESET                /* reset for ide not supported  */
 349
 350 #define CONFIG_SYS_IDE_MAXBUS           1       /* max. 1 IDE bus               */
 351 #define CONFIG_SYS_IDE_MAXDEVICE        1       /* max. 1 drive per IDE bus     */
 352
 353 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000
 354
 355 #define CONFIG_SYS_ATA_BASE_ADDR        CONFIG_SYS_PCMCIA_MEM_ADDR
 356
 357 /* Offset for data I/O                  */
 358 #define CONFIG_SYS_ATA_DATA_OFFSET      (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
 359
 360 /* Offset for normal register accesses  */
 361 #define CONFIG_SYS_ATA_REG_OFFSET       (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
 362
 363 /* Offset for alternate registers       */
 364 #define CONFIG_SYS_ATA_ALT_OFFSET       0x0100
 365
 366 /*-----------------------------------------------------------------------
 367  *
 368  *-----------------------------------------------------------------------
 369  *
 370  */
 371 #define CONFIG_SYS_DER 0
 372
 373 /*
 374  * Init Memory Controller:
 375  *
 376  * BR0/1 and OR0/1 (FLASH)
 377  */
 378
 379 #define FLASH_BASE0_PRELIM      0x40000000      /* FLASH bank #0        */
 380 #define FLASH_BASE1_PRELIM      0x60000000      /* FLASH bank #0        */
 381
 382 /* used to re-map FLASH both when starting from SRAM or FLASH:
 383  * restrict access enough to keep SRAM working (if any)
 384  * but not too much to meddle with FLASH accesses
 385  */
 386 #define CONFIG_SYS_REMAP_OR_AM          0x80000000      /* OR addr mask */
 387 #define CONFIG_SYS_PRELIM_OR_AM 0xE0000000      /* OR addr mask */
 388
 389 /*
 390  * FLASH timing: Default value of OR0 after reset
 391  */
 392 #define CONFIG_SYS_OR_TIMING_FLASH      (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
 393                                  OR_SCY_15_CLK | OR_TRLX)
 394
 395 #define CONFIG_SYS_OR0_REMAP    (CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
 396 #define CONFIG_SYS_OR0_PRELIM   (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
 397 #define CONFIG_SYS_BR0_PRELIM   ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
 398
 399 #define CONFIG_SYS_OR1_REMAP    CONFIG_SYS_OR0_REMAP
 400 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_OR0_PRELIM
 401 #define CONFIG_SYS_BR1_PRELIM   ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
 402
 403 /*
 404  * BR2/3 and OR2/3 (SDRAM)
 405  *
 406  */
 407 #define SDRAM_BASE2_PRELIM      0x00000000      /* SDRAM bank #0        */
 408 #define SDRAM_BASE3_PRELIM      0x20000000      /* SDRAM bank #1        */
 409 #define SDRAM_MAX_SIZE          (256 << 20)     /* max 256 MB per bank  */
 410
 411 /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)      */
 412 #define CONFIG_SYS_OR_TIMING_SDRAM      0x00000A00
 413
 414 #define CONFIG_SYS_OR2_PRELIM   (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
 415 #define CONFIG_SYS_BR2_PRELIM   ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
 416
 417 #ifndef CONFIG_CAN_DRIVER
 418 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_OR2_PRELIM
 419 #define CONFIG_SYS_BR3_PRELIM   ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
 420 #else   /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
 421 #define CONFIG_SYS_CAN_BASE             0xC0000000      /* CAN mapped at 0xC0000000     */
 422 #define CONFIG_SYS_CAN_OR_AM            0xFFFF8000      /* 32 kB address mask           */
 423 #define CONFIG_SYS_OR3_CAN              (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
 424 #define CONFIG_SYS_BR3_CAN              ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
 425                                         BR_PS_8 | BR_MS_UPMB | BR_V )
 426 #endif  /* CONFIG_CAN_DRIVER */
 427
 428 /*
 429  * 4096 Rows from SDRAM example configuration
 430  * 1000 factor s -> ms
 431  * 64   PTP (pre-divider from MPTPR) from SDRAM example configuration
 432  * 4    Number of refresh cycles per period
 433  * 64   Refresh cycle in ms per number of rows
 434  */
 435 #define CONFIG_SYS_PTA_PER_CLK  ((4096 * 64 * 1000) / (4 * 64))
 436
 437 /*
 438  * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad)
 439  *
 440  *                        CPUclock(MHz) * 31.2
 441  * CONFIG_SYS_MAMR_PTA = -----------------------------------     with DFBRG = 0
 442  *                2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16
 443  *
 444  * CPU clock =  15 MHz:  CONFIG_SYS_MAMR_PTA =  29   ->  4 * 7.73 us
 445  * CPU clock =  50 MHz:  CONFIG_SYS_MAMR_PTA =  97   ->  4 * 7.76 us
 446  * CPU clock =  66 MHz:  CONFIG_SYS_MAMR_PTA = 128   ->  4 * 7.75 us
 447  * CPU clock = 133 MHz:  CONFIG_SYS_MAMR_PTA = 255   ->  4 * 7.67 us
 448  *
 449  * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will
 450  * be met also in the default configuration, i.e. if environment variable
 451  * 'cpuclk' is not set.
 452  */
 453 #define CONFIG_SYS_MAMR_PTA             97
 454
 455 /*
 456  * Memory Periodic Timer Prescaler Register (MPTPR) values.
 457  */
 458 /* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */
 459 #define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16
 460 /* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */
 461 #define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8
 462
 463 /*
 464  * MAMR settings for SDRAM
 465  */
 466
 467 /* 8 column SDRAM */
 468 #define CONFIG_SYS_MAMR_8COL    ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 469                          MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |   \
 470                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 471 /* 9 column SDRAM */
 472 #define CONFIG_SYS_MAMR_9COL    ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 473                          MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |   \
 474                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 475 /* 10 column SDRAM */
 476 #define CONFIG_SYS_MAMR_10COL   ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 477                          MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9  |   \
 478                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 479
 480 #define CONFIG_SCC1_ENET
 481 #define CONFIG_FEC_ENET
 482 #define CONFIG_ETHPRIME         "SCC"
 483
 484 /* pass open firmware flat tree */
 485 #define CONFIG_OF_LIBFDT        1
 486 #define CONFIG_OF_BOARD_SETUP   1
 487 #define CONFIG_HWCONFIG         1
 488
 489 #endif  /* __CONFIG_H */