include/configs/TQM885D.h

   1 /*
   2  * (C) Copyright 2000-2014
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * (C) Copyright 2006
   6  * Martin Krause, TQ-Systems GmBH, martin.krause@tqs.de
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 /*
  12  * board/config.h - configuration options, board specific
  13  */
  14
  15 #ifndef __CONFIG_H
  16 #define __CONFIG_H
  17
  18 /*
  19  * High Level Configuration Options
  20  * (easy to change)
  21  */
  22
  23 #define CONFIG_MPC885           1       /* This is a MPC885 CPU         */
  24 #define CONFIG_TQM885D          1       /* ...on a TQM88D module        */
  25 #define CONFIG_DISPLAY_BOARDINFO
  26
  27 #define CONFIG_SYS_TEXT_BASE    0x40000000
  28
  29 #define CONFIG_8xx_OSCLK                10000000        /*  10 MHz - PLL input clock    */
  30 #define CONFIG_SYS_8xx_CPUCLK_MIN               15000000        /*  15 MHz - CPU minimum clock  */
  31 #define CONFIG_SYS_8xx_CPUCLK_MAX               133000000       /* 133 MHz - CPU maximum clock  */
  32 #define CONFIG_8xx_CPUCLK_DEFAULT       66000000        /*  66 MHz - CPU default clock  */
  33                                                 /* (it will be used if there is no      */
  34                                                 /* 'cpuclk' variable with valid value)  */
  35
  36 #define CONFIG_8xx_CONS_SMC1    1       /* Console is on SMC1           */
  37 #define CONFIG_SYS_SMC_RXBUFLEN 128
  38 #define CONFIG_SYS_MAXIDLE      10
  39 #define CONFIG_BAUDRATE         115200  /* console baudrate = 115kbps   */
  40
  41 #define CONFIG_BOOTCOUNT_LIMIT
  42
  43
  44 #define CONFIG_BOARD_TYPES      1       /* support board types          */
  45
  46 #define CONFIG_PREBOOT  "echo;" \
  47         "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
  48         "echo"
  49
  50 #undef  CONFIG_BOOTARGS
  51
  52 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
  53         "netdev=eth0\0"                                                 \
  54         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
  55                 "nfsroot=${serverip}:${rootpath}\0"                     \
  56         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
  57         "addip=setenv bootargs ${bootargs} "                            \
  58                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
  59                 ":${hostname}:${netdev}:off panic=1\0"                  \
  60         "flash_nfs=run nfsargs addip;"                                  \
  61                 "bootm ${kernel_addr}\0"                                \
  62         "flash_self=run ramargs addip;"                                 \
  63                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
  64         "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"     \
  65         "rootpath=/opt/eldk/ppc_8xx\0"                                  \
  66         "bootfile=/tftpboot/TQM885D/uImage\0"                           \
  67         "fdt_addr=400C0000\0"                                           \
  68         "kernel_addr=40100000\0"                                        \
  69         "ramdisk_addr=40280000\0"                                       \
  70         "load=tftp 200000 ${u-boot}\0"                                  \
  71         "update=protect off 40000000 +${filesize};"                     \
  72                 "erase 40000000 +${filesize};"                          \
  73                 "cp.b 200000 40000000 ${filesize};"                     \
  74                 "protect on 40000000 +${filesize}\0"                    \
  75         ""
  76 #define CONFIG_BOOTCOMMAND      "run flash_self"
  77
  78 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download  */
  79 #undef  CONFIG_SYS_LOADS_BAUD_CHANGE            /* don't allow baudrate change  */
  80
  81 #undef  CONFIG_WATCHDOG                 /* watchdog disabled            */
  82
  83 #define CONFIG_STATUS_LED       1       /* Status LED enabled           */
  84
  85 #undef  CONFIG_CAN_DRIVER               /* CAN Driver support disabled  */
  86
  87 /* enable I2C and select the hardware/software driver */
  88 #define CONFIG_SYS_I2C
  89 #define CONFIG_SYS_I2C_SOFT                     /* I2C bit-banged */
  90 #define CONFIG_SYS_I2C_SOFT_SPEED       93000   /* 93 kHz is supposed to work */
  91 #define CONFIG_SYS_I2C_SOFT_SLAVE       0xFE
  92 /*
  93  * Software (bit-bang) I2C driver configuration
  94  */
  95 #define PB_SCL          0x00000020      /* PB 26 */
  96 #define PB_SDA          0x00000010      /* PB 27 */
  97
  98 #define I2C_INIT        (immr->im_cpm.cp_pbdir |=  PB_SCL)
  99 #define I2C_ACTIVE      (immr->im_cpm.cp_pbdir |=  PB_SDA)
 100 #define I2C_TRISTATE    (immr->im_cpm.cp_pbdir &= ~PB_SDA)
 101 #define I2C_READ        ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
 102 #define I2C_SDA(bit)    if(bit) immr->im_cpm.cp_pbdat |=  PB_SDA; \
 103                         else    immr->im_cpm.cp_pbdat &= ~PB_SDA
 104 #define I2C_SCL(bit)    if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 105                         else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 106 #define I2C_DELAY       udelay(2)       /* 1/4 I2C clock duration */
 107
 108 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50            /* EEPROM AT24C??       */
 109 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2                /* two byte address     */
 110 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       4
 111 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* and takes up to 10 msec */
 112
 113 # define CONFIG_RTC_DS1337 1
 114 # define CONFIG_SYS_I2C_RTC_ADDR 0x68
 115
 116 /*
 117  * BOOTP options
 118  */
 119 #define CONFIG_BOOTP_SUBNETMASK
 120 #define CONFIG_BOOTP_GATEWAY
 121 #define CONFIG_BOOTP_HOSTNAME
 122 #define CONFIG_BOOTP_BOOTPATH
 123 #define CONFIG_BOOTP_BOOTFILESIZE
 124
 125 #define CONFIG_MAC_PARTITION
 126 #define CONFIG_DOS_PARTITION
 127
 128 #undef CONFIG_RTC_MPC8xx                /* MPC885 does not support RTC  */
 129
 130 #define CONFIG_TIMESTAMP                /* but print image timestmps    */
 131
 132 /*
 133  * Command line configuration.
 134  */
 135 #define CONFIG_CMD_DATE
 136 #define CONFIG_CMD_EEPROM
 137 #define CONFIG_CMD_IDE
 138
 139 /*
 140  * Miscellaneous configurable options
 141  */
 142 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
 143
 144 #define CONFIG_CMDLINE_EDITING  1       /* add command line history     */
 145
 146 #if defined(CONFIG_CMD_KGDB)
 147 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size      */
 148 #else
 149 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size      */
 150 #endif
 151 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 152 #define CONFIG_SYS_MAXARGS              16      /* max number of command args   */
 153 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 154
 155 #define CONFIG_SYS_MEMTEST_START        0x0100000       /* memtest works on     */
 156 #define CONFIG_SYS_MEMTEST_END          0x0300000       /* 1 ... 3 MB in DRAM   */
 157 #define CONFIG_SYS_ALT_MEMTEST                          /* alternate, more extensive
 158                                                    memory test.*/
 159
 160 #define CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */
 161
 162 /*
 163  * Low Level Configuration Settings
 164  * (address mappings, register initial values, etc.)
 165  * You should know what you are doing if you make changes here.
 166  */
 167 /*-----------------------------------------------------------------------
 168  * Internal Memory Mapped Register
 169  */
 170 #define CONFIG_SYS_IMMR         0xFFF00000
 171
 172 /*-----------------------------------------------------------------------
 173  * Definitions for initial stack pointer and data area (in DPRAM)
 174  */
 175 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_IMMR
 176 #define CONFIG_SYS_INIT_RAM_SIZE        0x2F00  /* Size of used area in DPRAM   */
 177 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 178 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 179
 180 /*-----------------------------------------------------------------------
 181  * Start addresses for the final memory configuration
 182  * (Set up by the startup code)
 183  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 184  */
 185 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 186 #define CONFIG_SYS_FLASH_BASE           0x40000000
 187 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for Monitor   */
 188 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
 189 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)     /* Reserve 128 kB for malloc()  */
 190
 191 /*
 192  * For booting Linux, the board info and command line data
 193  * have to be in the first 8 MB of memory, since this is
 194  * the maximum mapped by the Linux kernel during initialization.
 195  */
 196 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 197
 198 /*-----------------------------------------------------------------------
 199  * FLASH organization
 200  */
 201
 202 /* use CFI flash driver */
 203 #define CONFIG_SYS_FLASH_CFI            1       /* Flash is CFI conformant */
 204 #define CONFIG_FLASH_CFI_DRIVER 1       /* Use the common driver */
 205 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE }
 206 #define CONFIG_SYS_FLASH_EMPTY_INFO
 207 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE       1
 208 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max number of memory banks */
 209 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max number of sectors on one chip */
 210
 211 #define CONFIG_ENV_IS_IN_FLASH  1
 212 #define CONFIG_ENV_OFFSET               0x40000 /*   Offset   of Environment Sector     */
 213 #define CONFIG_ENV_SIZE         0x08000 /* Total Size of Environment            */
 214 #define CONFIG_ENV_SECT_SIZE    0x40000 /* Total Size of Environment Sector     */
 215
 216 /* Address and size of Redundant Environment Sector     */
 217 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
 218 #define CONFIG_ENV_SIZE_REDUND  (CONFIG_ENV_SIZE)
 219
 220 /*-----------------------------------------------------------------------
 221  * Hardware Information Block
 222  */
 223 #define CONFIG_SYS_HWINFO_OFFSET        0x0003FFC0      /* offset of HW Info block */
 224 #define CONFIG_SYS_HWINFO_SIZE          0x00000040      /* size   of HW Info block */
 225 #define CONFIG_SYS_HWINFO_MAGIC 0x54514D38      /* 'TQM8' */
 226
 227 /*-----------------------------------------------------------------------
 228  * Cache Configuration
 229  */
 230 #define CONFIG_SYS_CACHELINE_SIZE       16      /* For all MPC8xx CPUs                  */
 231 #if defined(CONFIG_CMD_KGDB)
 232 #define CONFIG_SYS_CACHELINE_SHIFT      4       /* log base 2 of the above value        */
 233 #endif
 234
 235 /*-----------------------------------------------------------------------
 236  * SYPCR - System Protection Control                            11-9
 237  * SYPCR can only be written once after reset!
 238  *-----------------------------------------------------------------------
 239  * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
 240  */
 241 #if defined(CONFIG_WATCHDOG)
 242 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
 243                          SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
 244 #else
 245 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
 246 #endif
 247
 248 /*-----------------------------------------------------------------------
 249  * SIUMCR - SIU Module Configuration                            11-6
 250  *-----------------------------------------------------------------------
 251  * PCMCIA config., multi-function pin tri-state
 252  */
 253 #ifndef CONFIG_CAN_DRIVER
 254 #define CONFIG_SYS_SIUMCR       (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
 255 #else   /* we must activate GPL5 in the SIUMCR for CAN */
 256 #define CONFIG_SYS_SIUMCR       (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
 257 #endif  /* CONFIG_CAN_DRIVER */
 258
 259 /*-----------------------------------------------------------------------
 260  * TBSCR - Time Base Status and Control                         11-26
 261  *-----------------------------------------------------------------------
 262  * Clear Reference Interrupt Status, Timebase freezing enabled
 263  */
 264 #define CONFIG_SYS_TBSCR        (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
 265
 266 /*-----------------------------------------------------------------------
 267  * PISCR - Periodic Interrupt Status and Control                11-31
 268  *-----------------------------------------------------------------------
 269  * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
 270  */
 271 #define CONFIG_SYS_PISCR        (PISCR_PS | PISCR_PITF)
 272
 273 /*-----------------------------------------------------------------------
 274  * SCCR - System Clock and reset Control Register               15-27
 275  *-----------------------------------------------------------------------
 276  * Set clock output, timebase and RTC source and divider,
 277  * power management and some other internal clocks
 278  */
 279 #define SCCR_MASK       SCCR_EBDF11
 280 #define CONFIG_SYS_SCCR (SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 281                          SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 282                          SCCR_DFALCD00)
 283
 284 /*-----------------------------------------------------------------------
 285  * PCMCIA stuff
 286  *-----------------------------------------------------------------------
 287  *
 288  */
 289 #define CONFIG_SYS_PCMCIA_MEM_ADDR      (0xE0000000)
 290 #define CONFIG_SYS_PCMCIA_MEM_SIZE      ( 64 << 20 )
 291 #define CONFIG_SYS_PCMCIA_DMA_ADDR      (0xE4000000)
 292 #define CONFIG_SYS_PCMCIA_DMA_SIZE      ( 64 << 20 )
 293 #define CONFIG_SYS_PCMCIA_ATTRB_ADDR    (0xE8000000)
 294 #define CONFIG_SYS_PCMCIA_ATTRB_SIZE    ( 64 << 20 )
 295 #define CONFIG_SYS_PCMCIA_IO_ADDR       (0xEC000000)
 296 #define CONFIG_SYS_PCMCIA_IO_SIZE       ( 64 << 20 )
 297
 298 /*-----------------------------------------------------------------------
 299  * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
 300  *-----------------------------------------------------------------------
 301  */
 302
 303 #define CONFIG_IDE_PREINIT      1       /* Use preinit IDE hook */
 304 #define CONFIG_IDE_8xx_PCCARD   1       /* Use IDE with PC Card Adapter */
 305
 306 #undef  CONFIG_IDE_8xx_DIRECT           /* Direct IDE    not supported  */
 307 #undef  CONFIG_IDE_LED                  /* LED   for ide not supported  */
 308 #undef  CONFIG_IDE_RESET                /* reset for ide not supported  */
 309
 310 #define CONFIG_SYS_IDE_MAXBUS           1       /* max. 1 IDE bus               */
 311 #define CONFIG_SYS_IDE_MAXDEVICE        1       /* max. 1 drive per IDE bus     */
 312
 313 #define CONFIG_SYS_ATA_IDE0_OFFSET      0x0000
 314
 315 #define CONFIG_SYS_ATA_BASE_ADDR        CONFIG_SYS_PCMCIA_MEM_ADDR
 316
 317 /* Offset for data I/O                  */
 318 #define CONFIG_SYS_ATA_DATA_OFFSET      (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
 319
 320 /* Offset for normal register accesses  */
 321 #define CONFIG_SYS_ATA_REG_OFFSET       (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
 322
 323 /* Offset for alternate registers       */
 324 #define CONFIG_SYS_ATA_ALT_OFFSET       0x0100
 325
 326 /*-----------------------------------------------------------------------
 327  *
 328  *-----------------------------------------------------------------------
 329  *
 330  */
 331 #define CONFIG_SYS_DER 0
 332
 333 /*
 334  * Init Memory Controller:
 335  *
 336  * BR0/1 and OR0/1 (FLASH)
 337  */
 338
 339 #define FLASH_BASE0_PRELIM      0x40000000      /* FLASH bank #0        */
 340 #define FLASH_BASE1_PRELIM      0x60000000      /* FLASH bank #0        */
 341
 342 /* used to re-map FLASH both when starting from SRAM or FLASH:
 343  * restrict access enough to keep SRAM working (if any)
 344  * but not too much to meddle with FLASH accesses
 345  */
 346 #define CONFIG_SYS_REMAP_OR_AM          0x80000000      /* OR addr mask */
 347 #define CONFIG_SYS_PRELIM_OR_AM 0xE0000000      /* OR addr mask */
 348
 349 /*
 350  * FLASH timing: Default value of OR0 after reset
 351  */
 352 #define CONFIG_SYS_OR_TIMING_FLASH      (OR_CSNT_SAM | OR_ACS_MSK | OR_BI | \
 353                                  OR_SCY_6_CLK | OR_TRLX)
 354
 355 #define CONFIG_SYS_OR0_REMAP    (CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
 356 #define CONFIG_SYS_OR0_PRELIM   (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
 357 #define CONFIG_SYS_BR0_PRELIM   ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
 358
 359 #define CONFIG_SYS_OR1_REMAP    CONFIG_SYS_OR0_REMAP
 360 #define CONFIG_SYS_OR1_PRELIM   CONFIG_SYS_OR0_PRELIM
 361 #define CONFIG_SYS_BR1_PRELIM   ((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )
 362
 363 /*
 364  * BR2/3 and OR2/3 (SDRAM)
 365  *
 366  */
 367 #define SDRAM_BASE2_PRELIM      0x00000000      /* SDRAM bank #0        */
 368 #define SDRAM_BASE3_PRELIM      0x20000000      /* SDRAM bank #1        */
 369 #define SDRAM_MAX_SIZE          (256 << 20)     /* max 256 MB per bank  */
 370
 371 /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)      */
 372 #define CONFIG_SYS_OR_TIMING_SDRAM      0x00000A00
 373
 374 #define CONFIG_SYS_OR2_PRELIM   (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
 375 #define CONFIG_SYS_BR2_PRELIM   ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
 376
 377 #ifndef CONFIG_CAN_DRIVER
 378 #define CONFIG_SYS_OR3_PRELIM   CONFIG_SYS_OR2_PRELIM
 379 #define CONFIG_SYS_BR3_PRELIM   ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
 380 #else   /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
 381 #define CONFIG_SYS_CAN_BASE             0xC0000000      /* CAN mapped at 0xC0000000     */
 382 #define CONFIG_SYS_CAN_OR_AM            0xFFFF8000      /* 32 kB address mask           */
 383 #define CONFIG_SYS_OR3_CAN              (CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
 384 #define CONFIG_SYS_BR3_CAN              ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
 385                                         BR_PS_8 | BR_MS_UPMB | BR_V )
 386 #endif  /* CONFIG_CAN_DRIVER */
 387
 388 /*
 389  * 4096 Rows from SDRAM example configuration
 390  * 1000 factor s -> ms
 391  * 64   PTP (pre-divider from MPTPR) from SDRAM example configuration
 392  * 4    Number of refresh cycles per period
 393  * 64   Refresh cycle in ms per number of rows
 394  */
 395 #define CONFIG_SYS_PTA_PER_CLK  ((4096 * 64 * 1000) / (4 * 64))
 396
 397 /*
 398  * Periodic timer (MAMR[PTx]) for 4 * 7.8 us refresh (= 31.2 us per quad)
 399  *
 400  *                        CPUclock(MHz) * 31.2
 401  * CONFIG_SYS_MAMR_PTA = -----------------------------------     with DFBRG = 0
 402  *                2^(2*SCCR[DFBRG]) * MPTPR_PTP_DIV16
 403  *
 404  * CPU clock =  15 MHz:  CONFIG_SYS_MAMR_PTA =  29   ->  4 * 7.73 us
 405  * CPU clock =  50 MHz:  CONFIG_SYS_MAMR_PTA =  97   ->  4 * 7.76 us
 406  * CPU clock =  66 MHz:  CONFIG_SYS_MAMR_PTA = 128   ->  4 * 7.75 us
 407  * CPU clock = 133 MHz:  CONFIG_SYS_MAMR_PTA = 255   ->  4 * 7.67 us
 408  *
 409  * Value 97 is for 4 * 7.8 us at 50 MHz. So the refresh cycle requirement will
 410  * be met also in the default configuration, i.e. if environment variable
 411  * 'cpuclk' is not set.
 412  */
 413 #define CONFIG_SYS_MAMR_PTA             128
 414
 415 /*
 416  * Memory Periodic Timer Prescaler Register (MPTPR) values.
 417  */
 418 /* 4 * 7.8 us refresh (= 31.2 us per quad) at 50 MHz and PTA = 97 */
 419 #define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16
 420 /* 4 * 3.9 us refresh (= 15.6 us per quad) at 50 MHz and PTA = 97 */
 421 #define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8
 422
 423 /*
 424  * MAMR settings for SDRAM
 425  */
 426
 427 /* 8 column SDRAM */
 428 #define CONFIG_SYS_MAMR_8COL    ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 429                          MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |   \
 430                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 431 /* 9 column SDRAM */
 432 #define CONFIG_SYS_MAMR_9COL    ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 433                          MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |   \
 434                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 435 /* 10 column SDRAM */
 436 #define CONFIG_SYS_MAMR_10COL   ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 437                          MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A9  |   \
 438                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 439
 440 /*
 441  * Network configuration
 442  */
 443 #define CONFIG_SCC2_ENET                /* enable ethernet on SCC2 */
 444 #define CONFIG_FEC_ENET                 /* enable ethernet on FEC */
 445 #define CONFIG_ETHER_ON_FEC1            /* ... for FEC1 */
 446 #define CONFIG_ETHER_ON_FEC2            /* ... for FEC2 */
 447
 448 #if defined(CONFIG_CMD_MII)
 449 #define CONFIG_SYS_DISCOVER_PHY
 450 #define CONFIG_MII_INIT 1
 451 #endif
 452
 453 #define CONFIG_NET_RETRY_COUNT 1        /* reduce max. timeout before
 454                                            switching to another netwok (if the
 455                                            tried network is unreachable) */
 456
 457 #define CONFIG_ETHPRIME         "SCC"
 458
 459 #define CONFIG_HWCONFIG         1
 460
 461 #endif  /* __CONFIG_H */