include/configs/davinci_dvevm.h

   1 /*
   2  * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net>
   3  *
   4  * SPDX-License-Identifier:     GPL-2.0+
   5  */
   6
   7 #ifndef __CONFIG_H
   8 #define __CONFIG_H
   9
  10 /*
  11  * Define this to make U-Boot skip low level initialization when loaded
  12  * by initial bootloader. Not required by NAND U-Boot version but IS
  13  * required for a NOR version used to burn the real NOR U-Boot into
  14  * NOR Flash. NAND and NOR support for DaVinci chips is mutually exclusive
  15  * so it is NOT possible to build a U-Boot with both NAND and NOR routines.
  16  * NOR U-Boot is loaded directly from Flash so it must perform all the
  17  * low level initialization itself. NAND version is loaded by an initial
  18  * bootloader (UBL in TI-ese) that performs such an initialization so it's
  19  * skipped in NAND version. The third DaVinci boot mode loads a bootloader
  20  * via UART0 and that bootloader in turn loads and runs U-Boot (or whatever)
  21  * performing low level init prior to loading. All that means we can NOT use
  22  * NAND version to put U-Boot into NOR because it doesn't have NOR support and
  23  * we can NOT use NOR version because it performs low level initialization
  24  * effectively destroying itself in DDR memory. That's why a separate NOR
  25  * version with this define is needed. It is loaded via UART, then one uses
  26  * it to somehow download a proper NOR version built WITHOUT this define to
  27  * RAM (tftp?) and burn it to NOR Flash. I would be probably able to squeeze
  28  * NOR support into the initial bootloader so it won't be needed but DaVinci
  29  * static RAM might be too small for this (I have something like 2Kbytes left
  30  * as of now, without NOR support) so this might've not happened...
  31  *
  32 #define CONFIG_NOR_UART_BOOT
  33  */
  34
  35 /*=======*/
  36 /* Board */
  37 /*=======*/
  38 #define DV_EVM
  39 #define CONFIG_SYS_NAND_SMALLPAGE
  40 #define CONFIG_SYS_USE_NAND
  41 /*===================*/
  42 /* SoC Configuration */
  43 /*===================*/
  44 #define CONFIG_SYS_TIMERBASE            0x01c21400      /* use timer 0 */
  45 #define CONFIG_SYS_HZ_CLOCK             27000000        /* Timer Input clock freq */
  46 #define CONFIG_SOC_DM644X
  47 /*====================================================*/
  48 /* EEPROM definitions for Atmel 24C256BN SEEPROM chip */
  49 /* on Sonata/DV_EVM board. No EEPROM on schmoogie.    */
  50 /*====================================================*/
  51 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
  52 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50
  53 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6
  54 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   20
  55 /*=============*/
  56 /* Memory Info */
  57 /*=============*/
  58 #define CONFIG_SYS_MALLOC_LEN           (0x10000 + 128*1024)    /* malloc() len */
  59 #define CONFIG_SYS_MEMTEST_START        0x80000000      /* memtest start address */
  60 #define CONFIG_SYS_MEMTEST_END          0x81000000      /* 16MB RAM test */
  61 #define CONFIG_NR_DRAM_BANKS    1               /* we have 1 bank of DRAM */
  62 #define PHYS_SDRAM_1            0x80000000      /* DDR Start */
  63 #define PHYS_SDRAM_1_SIZE       0x10000000      /* DDR size 256MB */
  64
  65 #define DDR_8BANKS                              /* 8-bank DDR2 (256MB) */
  66 /*====================*/
  67 /* Serial Driver info */
  68 /*====================*/
  69 #define CONFIG_SYS_NS16550
  70 #define CONFIG_SYS_NS16550_SERIAL
  71 #define CONFIG_SYS_NS16550_REG_SIZE     -4      /* NS16550 register size, byteorder */
  72 #define CONFIG_SYS_NS16550_COM1 0x01c20000      /* Base address of UART0 */
  73 #define CONFIG_SYS_NS16550_CLK  CONFIG_SYS_HZ_CLOCK     /* Input clock to NS16550 */
  74 #define CONFIG_CONS_INDEX       1               /* use UART0 for console */
  75 #define CONFIG_BAUDRATE         115200          /* Default baud rate */
  76 /*===================*/
  77 /* I2C Configuration */
  78 /*===================*/
  79 #define CONFIG_SYS_I2C
  80 #define CONFIG_SYS_I2C_DAVINCI
  81 #define CONFIG_SYS_DAVINCI_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */
  82 #define CONFIG_SYS_DAVINCI_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */
  83 /*==================================*/
  84 /* Network & Ethernet Configuration */
  85 /*==================================*/
  86 #define CONFIG_DRIVER_TI_EMAC
  87 #define CONFIG_MII
  88 #define CONFIG_BOOTP_DNS
  89 #define CONFIG_BOOTP_DNS2
  90 #define CONFIG_BOOTP_SEND_HOSTNAME
  91 #define CONFIG_NET_RETRY_COUNT  10
  92 /*=====================*/
  93 /* Flash & Environment */
  94 /*=====================*/
  95 #ifdef CONFIG_SYS_USE_NAND
  96 #define CONFIG_NAND_DAVINCI
  97 #define CONFIG_SYS_NAND_CS              2
  98 #undef CONFIG_ENV_IS_IN_FLASH
  99 #define CONFIG_SYS_NO_FLASH
 100 #define CONFIG_ENV_IS_IN_NAND           /* U-Boot env in NAND Flash  */
 101 #ifdef CONFIG_SYS_NAND_SMALLPAGE
 102 #define CONFIG_ENV_SECT_SIZE    512     /* Env sector Size */
 103 #define CONFIG_ENV_SIZE         (16 << 10)      /* 16 KiB */
 104 #define CONFIG_MTD_PARTITIONS
 105 #define CONFIG_MTD_DEVICE
 106 #define CONFIG_CMD_MTDPARTS
 107 #define MTDIDS_DEFAULT          \
 108         "nand0=davinci_nand.0"
 109 #define MTDPARTS_DEFAULT        \
 110         "mtdparts=davinci_nand.0:384k(bootloader)ro,4m(kernel),-(filesystem)"
 111 #else
 112 #define CONFIG_ENV_SECT_SIZE    2048    /* Env sector Size */
 113 #define CONFIG_ENV_SIZE         (128 << 10)     /* 128 KiB */
 114 #endif
 115 #define CONFIG_SKIP_LOWLEVEL_INIT       /* U-Boot is loaded by a bootloader */
 116 #define CONFIG_SYS_NAND_BASE            0x02000000
 117 #define CONFIG_SYS_NAND_USE_FLASH_BBT
 118 #define CONFIG_SYS_NAND_HW_ECC
 119 #define CONFIG_SYS_MAX_NAND_DEVICE      1       /* Max number of NAND devices */
 120 #define CONFIG_ENV_OFFSET               0x0     /* Block 0--not used by bootcode */
 121 #elif defined(CONFIG_SYS_USE_NOR)
 122 #ifdef CONFIG_NOR_UART_BOOT
 123 #define CONFIG_SKIP_LOWLEVEL_INIT       /* U-Boot is loaded by a bootloader */
 124 #else
 125 #undef CONFIG_SKIP_LOWLEVEL_INIT
 126 #endif
 127 #define CONFIG_ENV_IS_IN_FLASH
 128 #undef CONFIG_SYS_NO_FLASH
 129 #define CONFIG_FLASH_CFI_DRIVER
 130 #define CONFIG_SYS_FLASH_CFI
 131 #define CONFIG_SYS_MAX_FLASH_BANKS      1               /* max number of flash banks */
 132 #define CONFIG_SYS_FLASH_SECT_SZ        0x10000         /* 64KB sect size AMD Flash */
 133 #define CONFIG_ENV_OFFSET               (CONFIG_SYS_FLASH_SECT_SZ*3)
 134 #define PHYS_FLASH_1            0x02000000      /* CS2 Base address      */
 135 #define CONFIG_SYS_FLASH_BASE           PHYS_FLASH_1    /* Flash Base for U-Boot */
 136 #define PHYS_FLASH_SIZE         0x2000000       /* Flash size 32MB       */
 137 #define CONFIG_SYS_MAX_FLASH_SECT       (PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ)
 138 #define CONFIG_ENV_SECT_SIZE    CONFIG_SYS_FLASH_SECT_SZ        /* Env sector Size */
 139 #endif
 140 /*==============================*/
 141 /* U-Boot general configuration */
 142 /*==============================*/
 143 #define CONFIG_MISC_INIT_R
 144 #undef CONFIG_BOOTDELAY
 145 #define CONFIG_BOOTFILE         "uImage"        /* Boot file name */
 146 #define CONFIG_SYS_CBSIZE               1024            /* Console I/O Buffer Size  */
 147 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)        /* Print buffer sz */
 148 #define CONFIG_SYS_MAXARGS              16              /* max number of command args */
 149 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 150 #define CONFIG_SYS_LOAD_ADDR            0x80700000      /* default Linux kernel load address */
 151 #define CONFIG_VERSION_VARIABLE
 152 #define CONFIG_AUTO_COMPLETE            /* Won't work with hush so far, may be later */
 153 #define CONFIG_SYS_HUSH_PARSER
 154 #define CONFIG_CMDLINE_EDITING
 155 #define CONFIG_SYS_LONGHELP
 156 #define CONFIG_CRC32_VERIFY
 157 #define CONFIG_MX_CYCLIC
 158 #define CONFIG_USB_MUSB_HCD
 159 #define CONFIG_USB_DAVINCI
 160 /*===================*/
 161 /* Linux Information */
 162 /*===================*/
 163 #define LINUX_BOOT_PARAM_ADDR   0x80000100
 164 #define CONFIG_CMDLINE_TAG
 165 #define CONFIG_SETUP_MEMORY_TAGS
 166 #define CONFIG_BOOTARGS         "mem=120M console=ttyS0,115200n8 root=/dev/hda1 rw noinitrd ip=dhcp"
 167 #define CONFIG_BOOTCOMMAND      "setenv setboot setenv bootargs \\$(bootargs) video=dm64xxfb:output=\\$(videostd);run setboot; bootm 0x2050000"
 168 /*=================*/
 169 /* U-Boot commands */
 170 /*=================*/
 171 #define CONFIG_CMD_ASKENV
 172 #define CONFIG_CMD_DHCP
 173 #define CONFIG_CMD_DIAG
 174 #define CONFIG_CMD_I2C
 175 #define CONFIG_CMD_MII
 176 #define CONFIG_CMD_PING
 177 #define CONFIG_CMD_SAVES
 178 #define CONFIG_CMD_EEPROM
 179
 180 #ifdef CONFIG_CMD_BDI
 181 #define CONFIG_CLOCKS
 182 #endif
 183
 184 #ifdef CONFIG_SYS_USE_NAND
 185 #define CONFIG_CMD_NAND
 186 #elif defined(CONFIG_SYS_USE_NOR)
 187 #define CONFIG_CMD_JFFS2
 188 #else
 189 #error "Either CONFIG_SYS_USE_NAND or CONFIG_SYS_USE_NOR _MUST_ be defined !!!"
 190 #endif
 191 /*==========================*/
 192 /* USB MSC support (if any) */
 193 /*==========================*/
 194 #ifdef CONFIG_USB_DAVINCI
 195 #define CONFIG_CMD_USB
 196 #ifdef CONFIG_USB_MUSB_HCD
 197 #define CONFIG_USB_STORAGE
 198 #define CONFIG_CMD_STORAGE
 199 #define CONFIG_CMD_FAT
 200 #define CONFIG_DOS_PARTITION
 201 #endif
 202 #ifdef CONFIG_USB_KEYBOARD
 203 #define CONFIG_SYS_USB_EVENT_POLL
 204 #define CONFIG_PREBOOT "usb start"
 205 #endif
 206 #endif
 207
 208 #define CONFIG_MAX_RAM_BANK_SIZE        (256 << 20)     /* 256 MB */
 209
 210 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
 211 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000
 212 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_SDRAM_BASE + \
 213                                          CONFIG_SYS_INIT_RAM_SIZE - \
 214                                          GENERATED_GBL_DATA_SIZE)
 215
 216 #endif /* __CONFIG_H */