include/configs/ep8260.h

   1 /*
   2  * (C) Copyright 2002
   3  * Frank Panno <fpanno@delphintech.com>, Delphin Technology AG
   4  *
   5  * This file is based on similar values for other boards found in other
   6  * U-Boot config files, and some that I found in the EP8260 manual.
   7  *
   8  * See file CREDITS for list of people who contributed to this
   9  * project.
  10  *
  11  * This program is free software; you can redistribute it and/or
  12  * modify it under the terms of the GNU General Public License as
  13  * published by the Free Software Foundation; either version 2 of
  14  * the License, or (at your option) any later version.
  15  *
  16  * This program is distributed in the hope that it will be useful,
  17  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  18  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  19  * GNU General Public License for more details.
  20  *
  21  * You should have received a copy of the GNU General Public License
  22  * along with this program; if not, write to the Free Software
  23  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  24  * MA 02111-1307 USA
  25  */
  26
  27 /*
  28  * board/config.h - configuration options, board specific
  29  *
  30  * Note: my board is a "SBC 8260 H, V.1.1"
  31  *      - 64M 60x Bus SDRAM
  32  *      - 32M Local Bus SDRAM
  33  *      - 16M Flash (4 x AM29DL323DB90WDI)
  34  *      - 128k NVRAM with RTC
  35  */
  36
  37 #ifndef __CONFIG_H
  38 #define __CONFIG_H
  39
  40 /* What is the oscillator's (UX2) frequency in Hz? */
  41 #define CONFIG_8260_CLKIN  (66 * 1000 * 1000)
  42
  43 /*-----------------------------------------------------------------------
  44  * MODCK_H & MODCLK[1-3] - Ref: Section 9.2 in MPC8206 User Manual
  45  *-----------------------------------------------------------------------
  46  * What should MODCK_H be? It is dependent on the oscillator
  47  * frequency, MODCK[1-3], and desired CPM and core frequencies.
  48  * Here are some example values (all frequencies are in MHz):
  49  *
  50  * MODCK_H   MODCK[1-3]  Osc    CPM    Core
  51  * -------   ----------  ---    ---    ----
  52  * 0x2       0x2         33     133    133
  53  * 0x2       0x3         33     133    166
  54  * 0x2       0x4         33     133    200
  55  * 0x2       0x5         33     133    233
  56  * 0x2       0x6         33     133    266
  57  *
  58  * 0x5       0x5         66     133    133
  59  * 0x5       0x6         66     133    166
  60  * 0x5       0x7         66     133    200 *
  61  * 0x6       0x0         66     133    233
  62  * 0x6       0x1         66     133    266
  63  * 0x6       0x2         66     133    300
  64  */
  65 #define CFG_SBC_MODCK_H 0x05
  66
  67 /* Define this if you want to boot from 0x00000100. If you don't define
  68  * this, you will need to program the bootloader to 0xfff00000, and
  69  * get the hardware reset config words at 0xfe000000. The simplest
  70  * way to do that is to program the bootloader at both addresses.
  71  * It is suggested that you just let U-Boot live at 0x00000000.
  72  */
  73 /* #define CFG_SBC_BOOT_LOW 1 */        /* only for HRCW */
  74 /* #undef CFG_SBC_BOOT_LOW */
  75
  76 /* The reset command will not work as expected if the reset address does
  77  * not point to the correct address.
  78  */
  79
  80 #define CFG_RESET_ADDRESS       0xFFF00100
  81
  82 /* What should the base address of the main FLASH be and how big is
  83  * it (in MBytes)? This must contain TEXT_BASE from board/ep8260/config.mk
  84  * The main FLASH is whichever is connected to *CS0. U-Boot expects
  85  * this to be the SIMM.
  86  */
  87 #define CFG_FLASH0_BASE 0xFF000000
  88 #define CFG_FLASH0_SIZE 16
  89
  90 /* What should the base address of the secondary FLASH be and how big
  91  * is it (in Mbytes)? The secondary FLASH is whichever is connected
  92  * to *CS6. U-Boot expects this to be the on board FLASH. If you don't
  93  * want it enabled, don't define these constants.
  94  */
  95 #define CFG_FLASH1_BASE 0
  96 #define CFG_FLASH1_SIZE 0
  97 #undef CFG_FLASH1_BASE
  98 #undef CFG_FLASH1_SIZE
  99
 100 /* What should be the base address of SDRAM DIMM (60x bus) and how big is
 101  * it (in Mbytes)?
 102 */
 103 #define CFG_SDRAM0_BASE 0x00000000
 104 #define CFG_SDRAM0_SIZE 64
 105
 106 /* define CFG_LSDRAM if you want to enable the 32M SDRAM on the
 107  * local bus (8260 local bus is NOT cacheable!)
 108 */
 109 /* #define CFG_LSDRAM */
 110 #undef CFG_LSDRAM
 111
 112 #ifdef CFG_LSDRAM
 113 /* What should be the base address of SDRAM DIMM (local bus) and how big is
 114  * it (in Mbytes)?
 115 */
 116   #define CFG_SDRAM1_BASE 0x04000000
 117   #define CFG_SDRAM1_SIZE 32
 118 #else
 119   #define CFG_SDRAM1_BASE 0
 120   #define CFG_SDRAM1_SIZE 0
 121   #undef CFG_SDRAM1_BASE
 122   #undef CFG_SDRAM1_SIZE
 123 #endif /* CFG_LSDRAM */
 124
 125 /* What should be the base address of NVRAM and how big is
 126  * it (in Bytes)
 127  */
 128 #define CFG_NVRAM_BASE_ADDR  0xFa080000
 129 #define CFG_NVRAM_SIZE       (128*1024)-16
 130
 131 /* The RTC is a Dallas DS1556
 132  */
 133 #define CONFIG_RTC_DS1556
 134
 135 /* What should be the base address of the LEDs and switch S0?
 136  * If you don't want them enabled, don't define this.
 137  */
 138 #define CFG_LED_BASE 0x00000000
 139 #undef CFG_LED_BASE
 140
 141 /*
 142  * select serial console configuration
 143  *
 144  * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
 145  * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
 146  * for SCC).
 147  *
 148  * if CONFIG_CONS_NONE is defined, then the serial console routines must
 149  * defined elsewhere.
 150  */
 151 #define CONFIG_CONS_ON_SMC          /* define if console on SMC */
 152 #undef  CONFIG_CONS_ON_SCC          /* define if console on SCC */
 153 #undef  CONFIG_CONS_NONE            /* define if console on neither */
 154 #define CONFIG_CONS_INDEX    1      /* which SMC/SCC channel for console */
 155
 156 /*
 157  * select ethernet configuration
 158  *
 159  * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
 160  * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
 161  * for FCC)
 162  *
 163  * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
 164  * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
 165  * from CONFIG_COMMANDS to remove support for networking.
 166  */
 167 #undef  CONFIG_ETHER_ON_SCC           /* define if ethernet on SCC    */
 168 #define CONFIG_ETHER_ON_FCC           /* define if ethernet on FCC    */
 169 #undef  CONFIG_ETHER_NONE             /* define if ethernet on neither */
 170 #define CONFIG_ETHER_INDEX      3     /* which SCC/FCC channel for ethernet */
 171
 172 #if ( CONFIG_ETHER_INDEX == 3 )
 173
 174 /*
 175  * - Rx-CLK is CLK15
 176  * - Tx-CLK is CLK16
 177  * - RAM for BD/Buffers is on the local Bus (see 28-13)
 178  * - Enable Half Duplex in FSMR
 179  */
 180 # define CFG_CMXFCR_MASK        (CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
 181 # define CFG_CMXFCR_VALUE       (CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
 182
 183 /*
 184  * - RAM for BD/Buffers is on the local Bus (see 28-13)
 185  */
 186 #ifdef CFG_LSDRAM
 187   #define CFG_CPMFCR_RAMTYPE    3
 188 #else /* CFG_LSDRAM */
 189   #define CFG_CPMFCR_RAMTYPE    0
 190 #endif /* CFG_LSDRAM */
 191
 192 /* - Enable Half Duplex in FSMR */
 193 /* # define CFG_FCC_PSMR                (FCC_PSMR_FDE|FCC_PSMR_LPB) */
 194 # define CFG_FCC_PSMR           0
 195
 196 #else /* CONFIG_ETHER_INDEX */
 197 # error "on EP8260 ethernet must be FCC3"
 198 #endif /* CONFIG_ETHER_INDEX */
 199
 200 /*
 201  * select i2c support configuration
 202  *
 203  * Supported configurations are {none, software, hardware} drivers.
 204  * If the software driver is chosen, there are some additional
 205  * configuration items that the driver uses to drive the port pins.
 206  */
 207 #undef  CONFIG_HARD_I2C                 /* I2C with hardware support    */
 208 #define CONFIG_SOFT_I2C         1       /* I2C bit-banged               */
 209 #define CFG_I2C_SPEED           400000  /* I2C speed and slave address  */
 210 #define CFG_I2C_SLAVE           0x7F
 211
 212 /*
 213  * Software (bit-bang) I2C driver configuration
 214  */
 215 #ifdef CONFIG_SOFT_I2C
 216 #define I2C_PORT        3               /* Port A=0, B=1, C=2, D=3 */
 217 #define I2C_ACTIVE      (iop->pdir |=  0x00010000)
 218 #define I2C_TRISTATE    (iop->pdir &= ~0x00010000)
 219 #define I2C_READ        ((iop->pdat & 0x00010000) != 0)
 220 #define I2C_SDA(bit)    if(bit) iop->pdat |=  0x00010000; \
 221                         else    iop->pdat &= ~0x00010000
 222 #define I2C_SCL(bit)    if(bit) iop->pdat |=  0x00020000; \
 223                         else    iop->pdat &= ~0x00020000
 224 #define I2C_DELAY       udelay(5)       /* 1/4 I2C clock duration */
 225 #endif /* CONFIG_SOFT_I2C */
 226
 227 /* #define CONFIG_RTC_DS174x */
 228
 229 /* Define this to reserve an entire FLASH sector (256 KB) for
 230  * environment variables. Otherwise, the environment will be
 231  * put in the same sector as U-Boot, and changing variables
 232  * will erase U-Boot temporarily
 233  */
 234 #define CFG_ENV_IN_OWN_SECT
 235
 236 /* Define to allow the user to overwrite serial and ethaddr */
 237 #define CONFIG_ENV_OVERWRITE
 238
 239 /* What should the console's baud rate be? */
 240 /* #define CONFIG_BAUDRATE         57600 */
 241 #define CONFIG_BAUDRATE         115200
 242
 243 /* Ethernet MAC address */
 244 #define CONFIG_ETHADDR          00:10:EC:00:30:8C
 245
 246 #define CONFIG_IPADDR           192.168.254.130
 247 #define CONFIG_SERVERIP         192.168.254.49
 248
 249 /* Set to a positive value to delay for running BOOTCOMMAND */
 250 #define CONFIG_BOOTDELAY        -1
 251
 252 /* undef this to save memory */
 253 #define CFG_LONGHELP
 254
 255 /* Monitor Command Prompt       */
 256 #define CFG_PROMPT              "=> "
 257
 258 /* Define this variable to enable the "hush" shell (from
 259    Busybox) as command line interpreter, thus enabling
 260    powerful command line syntax like
 261    if...then...else...fi conditionals or `&&' and '||'
 262    constructs ("shell scripts").
 263    If undefined, you get the old, much simpler behaviour
 264    with a somewhat smapper memory footprint.
 265 */
 266 #define CFG_HUSH_PARSER
 267 #define CFG_PROMPT_HUSH_PS2     "> "
 268
 269 /* What U-Boot subsytems do you want enabled? */
 270 /*
 271 */
 272 #define CONFIG_COMMANDS         (       CFG_CMD_ALL     & \
 273                                         ~CFG_CMD_BMP    & \
 274                                         ~CFG_CMD_BSP    & \
 275                                         ~CFG_CMD_DCR    & \
 276                                         ~CFG_CMD_DHCP   & \
 277                                         ~CFG_CMD_DOC    & \
 278                                         ~CFG_CMD_EEPROM & \
 279                                         ~CFG_CMD_FDC    & \
 280                                         ~CFG_CMD_FDOS   & \
 281                                         ~CFG_CMD_HWFLOW & \
 282                                         ~CFG_CMD_IDE    & \
 283                                         ~CFG_CMD_JFFS2  & \
 284                                         ~CFG_CMD_KGDB   & \
 285                                         ~CFG_CMD_MII    & \
 286                                         ~CFG_CMD_MMC    & \
 287                                         ~CFG_CMD_NAND   & \
 288                                         ~CFG_CMD_PCI    & \
 289                                         ~CFG_CMD_PCMCIA & \
 290                                         ~CFG_CMD_SCSI   & \
 291                                         ~CFG_CMD_SPI    & \
 292                                         ~CFG_CMD_USB    & \
 293                                         ~CFG_CMD_VFD    & \
 294                                         ~CFG_CMD_DTT )
 295
 296 /* Where do the internal registers live? */
 297 #define CFG_IMMR               0xF0000000
 298 #define CFG_DEFAULT_IMMR       0x00010000
 299
 300 /* Where do the on board registers (CS4) live? */
 301 #define CFG_REGS_BASE          0xFA000000
 302
 303 /*****************************************************************************
 304  *
 305  * You should not have to modify any of the following settings
 306  *
 307  *****************************************************************************/
 308
 309 #define CONFIG_MPC8260          1       /* This is an MPC8260 CPU   */
 310 #define CONFIG_EP8260           11      /* on an Embedded Planet EP8260 Board, Rev. 11 */
 311
 312 #define CONFIG_BOARD_PRE_INIT   1           /* Call board_pre_init      */
 313
 314 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 315 #include <cmd_confdefs.h>
 316
 317 /*
 318  * Miscellaneous configurable options
 319  */
 320 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 321 #  define CFG_CBSIZE              1024       /* Console I/O Buffer Size      */
 322 #else
 323 #  define CFG_CBSIZE              256        /* Console I/O Buffer Size      */
 324 #endif
 325
 326 /* Print Buffer Size */
 327 #define CFG_PBSIZE        (CFG_CBSIZE + sizeof(CFG_PROMPT)+16)
 328
 329 #define CFG_MAXARGS       8            /* max number of command args   */
 330
 331 #define CFG_BARGSIZE      CFG_CBSIZE   /* Boot Argument Buffer Size    */
 332
 333 #ifdef CFG_LSDRAM
 334   #define CFG_MEMTEST_START 0x04000000   /* memtest works on  */
 335   #define CFG_MEMTEST_END   0x06000000   /* 64-96 MB in SDRAM */
 336 #else
 337   #define CFG_MEMTEST_START 0x00000000   /* memtest works on  */
 338   #define CFG_MEMTEST_END   0x02000000   /* 0-32 MB in SDRAM */
 339 #endif /* CFG_LSDRAM */
 340
 341 #define CONFIG_CLOCKS_IN_MHZ    1      /* clocks passsed to Linux in MHz */
 342
 343 #define CFG_LOAD_ADDR     0x00100000   /* default load address */
 344 #define CFG_TFTP_LOADADDR 0x00100000   /* default load address for network file downloads */
 345
 346 #define CFG_HZ            1000         /* decrementer freq: 1 ms ticks */
 347
 348 /* valid baudrates */
 349 #define CFG_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }
 350
 351 /*
 352  * Low Level Configuration Settings
 353  * (address mappings, register initial values, etc.)
 354  * You should know what you are doing if you make changes here.
 355  */
 356
 357 #define CFG_FLASH_BASE    CFG_FLASH0_BASE
 358 #define CFG_SDRAM_BASE    CFG_SDRAM0_BASE
 359
 360 /*-----------------------------------------------------------------------
 361  * Hard Reset Configuration Words
 362  */
 363
 364 #if defined(CFG_SBC_BOOT_LOW)
 365 #  define  CFG_SBC_HRCW_BOOT_FLAGS  (HRCW_CIP | HRCW_BMS)
 366 #else
 367 #  define  CFG_SBC_HRCW_BOOT_FLAGS  (0x00000000)
 368 #endif /* defined(CFG_SBC_BOOT_LOW) */
 369
 370 /* get the HRCW ISB field from CFG_IMMR */
 371 /*
 372 #define CFG_SBC_HRCW_IMMR ( ((CFG_IMMR & 0x10000000) >> 10) |\
 373                             ((CFG_IMMR & 0x01000000) >> 7)  |\
 374                             ((CFG_IMMR & 0x00100000) >> 4) )
 375
 376 #define CFG_HRCW_MASTER (HRCW_EBM                |\
 377                          HRCW_L2CPC01            |\
 378                          CFG_SBC_HRCW_IMMR       |\
 379                          HRCW_APPC10             |\
 380                          HRCW_CS10PC01           |\
 381                          HRCW_MODCK_H0101        |\
 382                          CFG_SBC_HRCW_BOOT_FLAGS)
 383 */
 384 #define CFG_HRCW_MASTER 0x10400245
 385
 386 /* no slaves */
 387 #define CFG_HRCW_SLAVE1 0
 388 #define CFG_HRCW_SLAVE2 0
 389 #define CFG_HRCW_SLAVE3 0
 390 #define CFG_HRCW_SLAVE4 0
 391 #define CFG_HRCW_SLAVE5 0
 392 #define CFG_HRCW_SLAVE6 0
 393 #define CFG_HRCW_SLAVE7 0
 394
 395 /*-----------------------------------------------------------------------
 396  * Definitions for initial stack pointer and data area (in DPRAM)
 397  */
 398 #define CFG_INIT_RAM_ADDR       CFG_IMMR
 399 #define CFG_INIT_RAM_END        0x4000  /* End of used area in DPRAM    */
 400 #define CFG_GBL_DATA_SIZE      128     /* bytes reserved for initial data */
 401 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 402 #define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
 403
 404 /*-----------------------------------------------------------------------
 405  * Start addresses for the final memory configuration
 406  * (Set up by the startup code)
 407  * Please note that CFG_SDRAM_BASE _must_ start at 0
 408  * Note also that the logic that sets CFG_RAMBOOT is platform dependent.
 409  */
 410 #define CFG_MONITOR_BASE          TEXT_BASE
 411
 412
 413 #if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
 414 #  define CFG_RAMBOOT
 415 #endif
 416
 417 #define CFG_MONITOR_LEN      (256 << 10)     /* Reserve 256 kB for Monitor   */
 418 #define CFG_MALLOC_LEN       (128 << 10)     /* Reserve 128 kB for malloc()  */
 419
 420 /*
 421  * For booting Linux, the board info and command line data
 422  * have to be in the first 8 MB of memory, since this is
 423  * the maximum mapped by the Linux kernel during initialization.
 424  */
 425 #define CFG_BOOTMAPSZ        (8 << 20)       /* Initial Memory map for Linux */
 426
 427 /*-----------------------------------------------------------------------
 428  * FLASH and environment organization
 429  */
 430 #define CFG_MAX_FLASH_BANKS   1       /* max number of memory banks         */
 431 #define CFG_MAX_FLASH_SECT    71      /* max number of sectors on one chip  */
 432
 433 #define CFG_FLASH_ERASE_TOUT  8000    /* Timeout for Flash Erase (in ms)    */
 434 #define CFG_FLASH_WRITE_TOUT  1       /* Timeout for Flash Write (in ms)    */
 435
 436 #ifndef CFG_RAMBOOT
 437 #  define CFG_ENV_IS_IN_FLASH  1
 438
 439 #  ifdef CFG_ENV_IN_OWN_SECT
 440 #    define CFG_ENV_ADDR       (CFG_MONITOR_BASE + 0x40000)
 441 #    define CFG_ENV_SECT_SIZE  0x40000
 442 #  else
 443 #    define CFG_ENV_ADDR (CFG_FLASH_BASE + CFG_MONITOR_LEN - CFG_ENV_SECT_SIZE)
 444 #    define CFG_ENV_SIZE       0x1000  /* Total Size of Environment Sector */
 445 #    define CFG_ENV_SECT_SIZE  0x10000 /* see README - env sect real size */
 446 #  endif /* CFG_ENV_IN_OWN_SECT */
 447 #else
 448 #  define CFG_ENV_IS_IN_NVRAM  1
 449 #  define CFG_ENV_ADDR         (CFG_MONITOR_BASE - 0x1000)
 450 #  define CFG_ENV_SIZE         0x200
 451 #endif /* CFG_RAMBOOT */
 452
 453 /*-----------------------------------------------------------------------
 454  * Cache Configuration
 455  */
 456 #define CFG_CACHELINE_SIZE      32      /* For MPC8260 CPU */
 457
 458 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 459 #  define CFG_CACHELINE_SHIFT     5     /* log base 2 of the above value */
 460 #endif
 461
 462 /*-----------------------------------------------------------------------
 463  * HIDx - Hardware Implementation-dependent Registers                    2-11
 464  *-----------------------------------------------------------------------
 465  * HID0 also contains cache control - initially enable both caches and
 466  * invalidate contents, then the final state leaves only the instruction
 467  * cache enabled. Note that Power-On and Hard reset invalidate the caches,
 468  * but Soft reset does not.
 469  *
 470  * HID1 has only read-only information - nothing to set.
 471  */
 472 #define CFG_HID0_INIT   (HID0_ICE  |\
 473                          HID0_DCE  |\
 474                          HID0_ICFI |\
 475                          HID0_DCI  |\
 476                          HID0_IFEM |\
 477                          HID0_ABE)
 478 #ifdef CFG_LSDRAM
 479 /* 8260 local bus is NOT cacheable */
 480 #define CFG_HID0_FINAL  (/*HID0_ICE  |*/\
 481                          HID0_IFEM |\
 482                          HID0_ABE  |\
 483                          HID0_EMCP)
 484 #else /* !CFG_LSDRAM */
 485 #define CFG_HID0_FINAL  (HID0_ICE  |\
 486                          HID0_IFEM |\
 487                          HID0_ABE  |\
 488                          HID0_EMCP)
 489 #endif /* CFG_LSDRAM */
 490
 491 #define CFG_HID2        0
 492
 493 /*-----------------------------------------------------------------------
 494  * RMR - Reset Mode Register
 495  *-----------------------------------------------------------------------
 496  */
 497 #define CFG_RMR         0
 498
 499 /*-----------------------------------------------------------------------
 500  * BCR - Bus Configuration                                       4-25
 501  *-----------------------------------------------------------------------
 502  */
 503 /*#define CFG_BCR         (BCR_EBM   |\
 504                          BCR_PLDP  |\
 505                          BCR_EAV   |\
 506                          BCR_NPQM1)
 507 */
 508 #define CFG_BCR  0x80C08000
 509 /*-----------------------------------------------------------------------
 510  * SIUMCR - SIU Module Configuration                             4-31
 511  *-----------------------------------------------------------------------
 512  */
 513
 514 #define CFG_SIUMCR      (SIUMCR_L2CPC01 |\
 515                          SIUMCR_APPC10  |\
 516                          SIUMCR_CS10PC01)
 517
 518
 519 /*-----------------------------------------------------------------------
 520  * SYPCR - System Protection Control                            11-9
 521  * SYPCR can only be written once after reset!
 522  *-----------------------------------------------------------------------
 523  * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
 524  */
 525 #ifdef CFG_LSDRAM
 526 #define CFG_SYPCR       (SYPCR_SWTC |\
 527                          SYPCR_BMT  |\
 528                          SYPCR_PBME |\
 529                          SYPCR_LBME |\
 530                          SYPCR_SWP)
 531 #else
 532 #define CFG_SYPCR       (SYPCR_SWTC |\
 533                          SYPCR_BMT  |\
 534                          SYPCR_PBME |\
 535                          SYPCR_SWP)
 536 #endif
 537 /*-----------------------------------------------------------------------
 538  * TMCNTSC - Time Counter Status and Control                     4-40
 539  *-----------------------------------------------------------------------
 540  * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
 541  * and enable Time Counter
 542  */
 543 #define CFG_TMCNTSC     (TMCNTSC_SEC |\
 544                          TMCNTSC_ALR |\
 545                          TMCNTSC_TCF |\
 546                          TMCNTSC_TCE)
 547
 548 /*-----------------------------------------------------------------------
 549  * PISCR - Periodic Interrupt Status and Control                 4-42
 550  *-----------------------------------------------------------------------
 551  * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
 552  * Periodic timer
 553  */
 554 /*#define CFG_PISCR       (PISCR_PS  |\
 555                          PISCR_PTF |\
 556                          PISCR_PTE)*/
 557 #define CFG_PISCR       0
 558 /*-----------------------------------------------------------------------
 559  * SCCR - System Clock Control                                   9-8
 560  *-----------------------------------------------------------------------
 561  */
 562 #define CFG_SCCR        (SCCR_DFBRG01)
 563
 564 /*-----------------------------------------------------------------------
 565  * RCCR - RISC Controller Configuration                         13-7
 566  *-----------------------------------------------------------------------
 567  */
 568 #define CFG_RCCR        0
 569
 570 /*-----------------------------------------------------------------------
 571  * MPTPR - Memory Refresh Timer Prescale Register               10-32
 572  *-----------------------------------------------------------------------
 573  */
 574 #define CFG_MPTPR       (0x0A00 & MPTPR_PTP_MSK)
 575
 576 /*
 577  * Init Memory Controller:
 578  *
 579  * Bank Bus     Machine PortSz  Device
 580  * ---- ---     ------- ------  ------
 581  *  0   60x     GPCM    64 bit  FLASH (BGA - 16MB AMD AM29DL323DB90WDI)
 582  *  1   60x     SDRAM   64 bit  SDRAM (BGA - 64MB Micron 48LC8M16A2TG)
 583  *  2   Local   SDRAM   32 bit  SDRAM (BGA - 32MB Micron 48LC8M16A2TG)
 584  *  3   unused
 585  *  4   60x     GPCM     8 bit  Board Regs, NVRTC
 586  *  5   unused
 587  *  6   unused
 588  *  7   unused
 589  *  8   PCMCIA
 590  *  9   unused
 591  * 10   unused
 592  * 11   unused
 593 */
 594
 595 /*-----------------------------------------------------------------------
 596  * BRx - Base Register
 597  *     Ref: Section 10.3.1 on page 10-14
 598  * ORx - Option Register
 599  *     Ref: Section 10.3.2 on page 10-18
 600  *-----------------------------------------------------------------------
 601  */
 602
 603 /* Bank 0 - FLASH
 604  *
 605  */
 606 #define CFG_BR0_PRELIM  ((CFG_FLASH0_BASE & BRx_BA_MSK) |\
 607                          BRx_PS_64                      |\
 608                          BRx_DECC_NONE                  |\
 609                          BRx_MS_GPCM_P                  |\
 610                          BRx_V)
 611
 612 #define CFG_OR0_PRELIM  (MEG_TO_AM(CFG_FLASH0_SIZE)     |\
 613                          ORxG_CSNT                      |\
 614                          ORxG_ACS_DIV1                  |\
 615                          ORxG_SCY_6_CLK                 |\
 616                          ORxG_EHTR)
 617
 618 /* Bank 1 - SDRAM
 619  * PSDRAM
 620  */
 621 #define CFG_BR1_PRELIM  ((CFG_SDRAM0_BASE & BRx_BA_MSK) |\
 622                          BRx_PS_64                      |\
 623                          BRx_MS_SDRAM_P                 |\
 624                          BRx_V)
 625
 626 #define CFG_OR1_PRELIM  (MEG_TO_AM(CFG_SDRAM0_SIZE)     |\
 627                          ORxS_BPD_4                     |\
 628                          ORxS_ROWST_PBI1_A6             |\
 629                          ORxS_NUMR_12)
 630
 631 #define CFG_PSDMR       0xC34E2462
 632 #define CFG_PSRT        0x64
 633
 634
 635 #ifdef CFG_LSDRAM
 636 /* Bank 2 - SDRAM
 637  * LSDRAM
 638  */
 639
 640   #define CFG_BR2_PRELIM  ((CFG_SDRAM1_BASE & BRx_BA_MSK) |\
 641                            BRx_PS_32                      |\
 642                            BRx_MS_SDRAM_L                 |\
 643                            BRx_V)
 644
 645   #define CFG_OR2_PRELIM  (MEG_TO_AM(CFG_SDRAM1_SIZE)     |\
 646                            ORxS_BPD_4                     |\
 647                            ORxS_ROWST_PBI0_A9             |\
 648                            ORxS_NUMR_12)
 649
 650   #define CFG_LSDMR       0x416A2562
 651   #define CFG_LSRT      0x64
 652 #else
 653   #define CFG_LSRT      0x0
 654 #endif /* CFG_LSDRAM */
 655
 656 /* Bank 4 - On board registers
 657  * NVRTC and BCSR
 658  */
 659 #define CFG_BR4_PRELIM   ((CFG_REGS_BASE & BRx_BA_MSK)  |\
 660                            BRx_PS_8                     |\
 661                            BRx_MS_GPCM_P                |\
 662                            BRx_V)
 663 /*
 664 #define CFG_OR4_PRELIM    (ORxG_AM_MSK                 |\
 665                            ORxG_CSNT                   |\
 666                            ORxG_ACS_DIV1               |\
 667                            ORxG_SCY_10_CLK              |\
 668                            ORxG_TRLX)
 669 */
 670 #define CFG_OR4_PRELIM 0xfff00854
 671
 672 /* Bank 8 - On board registers
 673  * PCMCIA (currently not working!)
 674  */
 675 #define CFG_BR8_PRELIM   ((CFG_REGS_BASE & BRx_BA_MSK)  |\
 676                            BRx_PS_16                     |\
 677                            BRx_MS_GPCM_P                |\
 678                            BRx_V)
 679
 680 #define CFG_OR8_PRELIM    (ORxG_AM_MSK                 |\
 681                            ORxG_CSNT                   |\
 682                            ORxG_ACS_DIV1               |\
 683                            ORxG_SETA                   |\
 684                            ORxG_SCY_10_CLK)
 685
 686 /*
 687  * Internal Definitions
 688  *
 689  * Boot Flags
 690  */
 691 #define BOOTFLAG_COLD   0x01    /* Normal Power-On: Boot from FLASH  */
 692 #define BOOTFLAG_WARM   0x02    /* Software reboot                   */
 693
 694 #endif  /* __CONFIG_H */