include/configs/gr_ep2s60.h

   1 /* Configuration header file for Gaisler Research AB's Template
   2  * design (GPL Open Source SPARC/LEON3 96MHz) for Altera NIOS
   3  * Development board Stratix II edition, with the FPGA device
   4  * EP2S60.
   5  *
   6  * (C) Copyright 2003-2005
   7  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   8  *
   9  * (C) Copyright 2008
  10  * Daniel Hellstrom, Gaisler Research, daniel@gaisler.com.
  11  *
  12  * SPDX-License-Identifier:     GPL-2.0+
  13  */
  14
  15 #ifndef __CONFIG_H__
  16 #define __CONFIG_H__
  17
  18 /*
  19  * High Level Configuration Options
  20  * (easy to change)
  21  */
  22
  23 /* Altera NIOS Development board, Stratix II board */
  24 #define CONFIG_GR_EP2S60        1
  25
  26 /* CPU / AMBA BUS configuration */
  27 #define CONFIG_SYS_CLK_FREQ     96000000        /* 96MHz */
  28
  29 /* Define this is the GR-2S60-MEZZ mezzanine is available and you
  30  * want to use the USB and GRETH functionality of the board
  31  */
  32 #undef GR_2S60_MEZZ
  33
  34 #ifdef GR_2S60_MEZZ
  35 #define USE_GRETH 1
  36 #define USE_GRUSB 1
  37 #endif
  38
  39 /*
  40  * Serial console configuration
  41  */
  42 #define CONFIG_BAUDRATE         38400   /* ... at 38400 bps */
  43 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200, 230400 }
  44
  45 /* Partitions */
  46
  47 /*
  48  * Supported commands
  49  */
  50 #define CONFIG_CMD_REGINFO
  51 #define CONFIG_CMD_DIAG
  52 #define CONFIG_CMD_IRQ
  53
  54 /* USB support */
  55 #if USE_GRUSB
  56 #define CONFIG_USB_UHCI
  57 /* Enable needed helper functions */
  58 #endif
  59
  60 /*
  61  * Autobooting
  62  */
  63
  64 #define CONFIG_PREBOOT  "echo;" \
  65         "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
  66         "echo"
  67
  68 #undef  CONFIG_BOOTARGS
  69
  70 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
  71         "netdev=eth0\0"                                                 \
  72         "nfsargs=setenv bootargs console=ttyS0,38400 root=/dev/nfs rw " \
  73                 "nfsroot=${serverip}:${rootpath}\0"                     \
  74         "ramargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/ram rw\0"                  \
  75         "addip=setenv bootargs ${bootargs} "                            \
  76                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
  77                 ":${hostname}:${netdev}:off panic=1\0"                  \
  78         "flash_nfs=run nfsargs addip;"                                  \
  79                 "bootm ${kernel_addr}\0"                                \
  80         "flash_self=run ramargs addip;"                                 \
  81                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
  82         "net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0"   \
  83         "scratch=40800000\0"                                    \
  84         "getkernel=tftpboot $(scratch) $(bootfile)\0" \
  85         "bootargs=console=ttyS0,38400 root=/dev/nfs rw nfsroot=192.168.0.20:/export/rootfs ip=192.168.0.207:192.168.0.20:192.168.0.1:255.255.255.0:ml401:eth0\0" \
  86         ""
  87
  88 #define CONFIG_NETMASK 255.255.255.0
  89 #define CONFIG_GATEWAYIP 192.168.0.1
  90 #define CONFIG_SERVERIP 192.168.0.20
  91 #define CONFIG_IPADDR 192.168.0.207
  92 #define CONFIG_ROOTPATH "/export/rootfs"
  93 #define CONFIG_HOSTNAME  ml401
  94 #define CONFIG_BOOTFILE "/uImage"
  95
  96 #define CONFIG_BOOTCOMMAND      "run flash_self"
  97
  98 /* Memory MAP
  99  *
 100  *  Flash:
 101  *  |--------------------------------|
 102  *  | 0x00000000 Text & Data & BSS   | *
 103  *  |            for Monitor         | *
 104  *  | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| *
 105  *  | UNUSED / Growth                | * 256kb
 106  *  |--------------------------------|
 107  *  | 0x00050000 Base custom area    | *
 108  *  |            kernel / FS         | *
 109  *  |                                | * Rest of Flash
 110  *  |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~|
 111  *  | END-0x00008000 Environment     | * 32kb
 112  *  |--------------------------------|
 113  *
 114  *
 115  *
 116  *  Main Memory:
 117  *  |--------------------------------|
 118  *  | UNUSED / scratch area          |
 119  *  |                                |
 120  *  |                                |
 121  *  |                                |
 122  *  |                                |
 123  *  |--------------------------------|
 124  *  | Monitor .Text / .DATA / .BSS   | * 512kb
 125  *  | Relocated!                     | *
 126  *  |--------------------------------|
 127  *  | Monitor Malloc                 | * 128kb (contains relocated environment)
 128  *  |--------------------------------|
 129  *  | Monitor/kernel STACK           | * 64kb
 130  *  |--------------------------------|
 131  *  | Page Table for MMU systems     | * 2k
 132  *  |--------------------------------|
 133  *  | PROM Code accessed from Linux  | * 6kb-128b
 134  *  |--------------------------------|
 135  *  | Global data (avail from kernel)| * 128b
 136  *  |--------------------------------|
 137  *
 138  */
 139
 140 /*
 141  * Flash configuration (8,16 or 32 MB)
 142  * TEXT base always at 0xFFF00000
 143  * ENV_ADDR always at  0xFFF40000
 144  * FLASH_BASE at 0xFC000000 for 64 MB
 145  *               0xFE000000 for 32 MB
 146  *               0xFF000000 for 16 MB
 147  *               0xFF800000 for  8 MB
 148  */
 149 /*#define CONFIG_SYS_NO_FLASH           1*/
 150 #define CONFIG_SYS_FLASH_BASE           0x00000000
 151 #define CONFIG_SYS_FLASH_SIZE           0x00400000      /* FPGA Bit file is in top of FLASH, we only ues the bottom 4Mb */
 152
 153 #define PHYS_FLASH_SECT_SIZE    0x00010000      /* 64 KB sectors */
 154 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max num of sects on one chip */
 155 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max num of memory banks      */
 156
 157 #define CONFIG_SYS_FLASH_ERASE_TOUT     240000  /* Flash Erase Timeout (in ms)  */
 158 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (in ms)  */
 159 #define CONFIG_SYS_FLASH_LOCK_TOUT      5       /* Timeout for Flash Set Lock Bit (in ms) */
 160 #define CONFIG_SYS_FLASH_UNLOCK_TOUT    10000   /* Timeout for Flash Clear Lock Bits (in ms) */
 161 #define CONFIG_SYS_FLASH_PROTECTION     /* "Real" (hardware) sectors protection */
 162
 163 /*** CFI CONFIG ***/
 164 #define CONFIG_SYS_FLASH_CFI_WIDTH      FLASH_CFI_8BIT
 165 #define CONFIG_FLASH_CFI_DRIVER
 166 #define CONFIG_SYS_FLASH_CFI
 167 /* Bypass cache when reading regs from flash memory */
 168 #define CONFIG_SYS_FLASH_CFI_BYPASS_READ
 169 /* Buffered writes (32byte/go) instead of single accesses */
 170 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 171
 172 /*
 173  * Environment settings
 174  */
 175 /*#define CONFIG_ENV_IS_NOWHERE 1*/
 176 #define CONFIG_ENV_IS_IN_FLASH  1
 177 /* CONFIG_ENV_ADDR need to be at sector boundary */
 178 #define CONFIG_ENV_SIZE         0x8000
 179 #define CONFIG_ENV_SECT_SIZE    0x20000
 180 #define CONFIG_ENV_ADDR         (CONFIG_SYS_FLASH_BASE+CONFIG_SYS_FLASH_SIZE-CONFIG_ENV_SECT_SIZE)
 181 #define CONFIG_ENV_OVERWRITE    1
 182
 183 /*
 184  * Memory map
 185  */
 186 #define CONFIG_SYS_SDRAM_BASE           0x40000000
 187 #define CONFIG_SYS_SDRAM_SIZE           0x02000000
 188 #define CONFIG_SYS_SDRAM_END            (CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_SDRAM_SIZE)
 189
 190 /* no SRAM available */
 191 #undef CONFIG_SYS_SRAM_BASE
 192 #undef CONFIG_SYS_SRAM_SIZE
 193
 194 #define CONFIG_SYS_RAM_BASE CONFIG_SYS_SDRAM_BASE
 195 #define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SDRAM_SIZE
 196 #define CONFIG_SYS_RAM_END CONFIG_SYS_SDRAM_END
 197
 198 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_SDRAM_END - GENERATED_GBL_DATA_SIZE)
 199
 200 #define CONFIG_SYS_PROM_SIZE            (8192-GENERATED_GBL_DATA_SIZE)
 201 #define CONFIG_SYS_PROM_OFFSET          (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
 202
 203 #define CONFIG_SYS_INIT_SP_OFFSET       (CONFIG_SYS_PROM_OFFSET-32)
 204 #define CONFIG_SYS_STACK_SIZE           (0x10000-32)
 205
 206 #define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 207 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 208 #   define CONFIG_SYS_RAMBOOT           1
 209 #endif
 210
 211 #define CONFIG_SYS_MONITOR_LEN          (512 << 10)     /* Reserve 512 kB for Monitor   */
 212 #define CONFIG_SYS_MALLOC_LEN           (128 << 10)     /* Reserve 128 kB for malloc()  */
 213 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 214
 215 #define CONFIG_SYS_MALLOC_END           (CONFIG_SYS_INIT_SP_OFFSET-CONFIG_SYS_STACK_SIZE)
 216 #define CONFIG_SYS_MALLOC_BASE          (CONFIG_SYS_MALLOC_END-CONFIG_SYS_MALLOC_LEN)
 217
 218 /* relocated monitor area */
 219 #define CONFIG_SYS_RELOC_MONITOR_MAX_END   CONFIG_SYS_MALLOC_BASE
 220 #define CONFIG_SYS_RELOC_MONITOR_BASE     (CONFIG_SYS_RELOC_MONITOR_MAX_END-CONFIG_SYS_MONITOR_LEN)
 221
 222 /* make un relocated address from relocated address */
 223 #define UN_RELOC(address) (address-(CONFIG_SYS_RELOC_MONITOR_BASE-CONFIG_SYS_TEXT_BASE))
 224
 225 /*
 226  * Ethernet configuration uses on board SMC91C111, however if a mezzanine
 227  * with a PHY is attached the GRETH can be used on this board.
 228  * Define USE_GRETH in order to use the mezzanine provided PHY with the
 229  * onchip GRETH network MAC, note that this is not supported by the
 230  * template design.
 231  */
 232 #ifndef USE_GRETH
 233
 234 /* USE SMC91C111 MAC */
 235 #define CONFIG_SMC91111          1
 236 #define CONFIG_SMC91111_BASE            0x20000300      /* chip select 3         */
 237 #define CONFIG_SMC_USE_32_BIT           1       /* 32 bit bus  */
 238 #undef  CONFIG_SMC_91111_EXT_PHY        /* we use internal phy   */
 239 /*#define CONFIG_SHOW_ACTIVITY*/
 240 #define CONFIG_NET_RETRY_COUNT          10      /* # of retries          */
 241
 242 #else
 243
 244 /* USE GRETH Ethernet Driver */
 245 #define CONFIG_GRETH    1
 246 #endif
 247
 248 #define CONFIG_PHY_ADDR  0x00
 249
 250 /*
 251  * Miscellaneous configurable options
 252  */
 253 #define CONFIG_SYS_LONGHELP             /* undef to save memory     */
 254 #if defined(CONFIG_CMD_KGDB)
 255 #define CONFIG_SYS_CBSIZE               1024    /* Console I/O Buffer Size  */
 256 #else
 257 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size  */
 258 #endif
 259 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)      /* Print Buffer Size */
 260 #define CONFIG_SYS_MAXARGS              16      /* max number of command args   */
 261 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 262
 263 #define CONFIG_SYS_MEMTEST_START        0x00100000      /* memtest works on */
 264 #define CONFIG_SYS_MEMTEST_END          0x00f00000      /* 1 ... 15 MB in DRAM  */
 265
 266 #define CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */
 267
 268 /*-----------------------------------------------------------------------
 269  * USB stuff
 270  *-----------------------------------------------------------------------
 271  */
 272 #define CONFIG_USB_CLOCK        0x0001BBBB
 273 #define CONFIG_USB_CONFIG       0x00005000
 274
 275 /***** Gaisler GRLIB IP-Cores Config ********/
 276
 277 #define CONFIG_SYS_GRLIB_SDRAM    0
 278
 279 /* No SDRAM Configuration */
 280 #undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
 281
 282 /* See, GRLIB Docs (grip.pdf) on how to set up
 283  * These the memory controller registers.
 284  */
 285 #define CONFIG_SYS_GRLIB_ESA_MCTRL1
 286 #define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1  (0x10f800ff | (1<<11))
 287 #define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2  0x00000000
 288 #define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3  0x00000000
 289
 290 /* GRLIB FT-MCTRL configuration */
 291 #define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
 292 #define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1  (0x10f800ff | (1<<11))
 293 #define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2  0x00000000
 294 #define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3  0x00000000
 295
 296 /* DDR controller */
 297 #define CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
 298 #define CONFIG_SYS_GRLIB_GAISLER_DDRSPA1_CTRL  0xa900830a
 299
 300 /* no DDR2 Controller */
 301 #undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
 302
 303 /* default kernel command line */
 304 #define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"
 305
 306 #endif                          /* __CONFIG_H */