]> git.ipfire.org Git - people/ms/u-boot.git/blob - include/configs/idmr.h
Merge branch 'u-boot/master' into u-boot-arm/master
[people/ms/u-boot.git] / include / configs / idmr.h
1 /*
2 * Configuration settings for the iDMR board
3 *
4 * Based on MC5272C3, r5200 and M5271EVB board configs
5 * (C) Copyright 2006 Wolfgang Denk, DENX Software Engineering, wd@denx.de.
6 * (C) Copyright 2006 Lab X Technologies <zachary.landau@labxtechnologies.com>
7 * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
8 *
9 * SPDX-License-Identifier: GPL-2.0+
10 */
11
12 #ifndef _IDMR_H
13 #define _IDMR_H
14
15
16 /*
17 * High Level Configuration Options (easy to change)
18 */
19
20 #define CONFIG_MCF52x2 /* define processor family */
21 #define CONFIG_M5271 /* define processor type */
22 #define CONFIG_IDMR /* define board type */
23
24 #undef CONFIG_WATCHDOG /* disable watchdog */
25
26 /*
27 * Default environment settings
28 */
29 #define CONFIG_BOOTCOMMAND "run net_nfs"
30 #define CONFIG_BOOTDELAY 5
31 #define CONFIG_MCFUART
32 #define CONFIG_SYS_UART_PORT (0)
33 #define CONFIG_BAUDRATE 19200
34 #define CONFIG_ETHADDR 00:06:3b:01:41:55
35 #define CONFIG_ETHPRIME
36 #define CONFIG_IPADDR 192.168.30.1
37 #define CONFIG_SERVERIP 192.168.1.1
38 #define CONFIG_ROOTPATH ""
39 #define CONFIG_GATEWAYIP 192.168.1.1
40 #define CONFIG_NETMASK 255.255.0.0
41 #define CONFIG_HOSTNAME idmr
42 #define CONFIG_BOOTFILE "/tftpboot/idmr/uImage"
43 #define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root " \
44 "filesystem over NFS; echo"
45
46 #define CONFIG_MCFTMR
47
48 #define CONFIG_EXTRA_ENV_SETTINGS \
49 "netdev=eth0\0" \
50 "ramargs=setenv bootargs root=/dev/ram rw\0" \
51 "addip=setenv bootargs $(bootargs) " \
52 "ip=$(ipaddr):$(serverip):$(gatewayip):" \
53 "$(netmask):$(hostname):$(netdev):off panic=1\0" \
54 "flash_nfs=run nfsargs addip;bootm $(kernel_addr)\0" \
55 "flash_self=run ramargs addip;bootm $(kernel_addr) " \
56 "$(ramdisk_addr)\0" \
57 "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
58 "nfsargs=setenv bootargs root=/dev/nfs rw " \
59 "nfsroot=$(serverip):$(rootpath)\0" \
60 "ethact=FEC\0 " \
61 "update=prot off ff800000 ff81ffff; era ff800000 ff81ffff; " \
62 "cp.b 200000 ff800000 $(filesize);" \
63 "prot on ff800000 ff81ffff\0" \
64 "load=tftp 200000 $(u-boot)\0" \
65 "u-boot=/tftpboot/idmr/u-boot.bin\0" \
66 ""
67
68
69 /*
70 * BOOTP options
71 */
72 #define CONFIG_BOOTP_BOOTFILESIZE
73 #define CONFIG_BOOTP_BOOTPATH
74 #define CONFIG_BOOTP_GATEWAY
75 #define CONFIG_BOOTP_HOSTNAME
76
77
78 /*
79 * Command line configuration.
80 */
81 #include <config_cmd_default.h>
82
83 #define CONFIG_CMD_PING
84 #define CONFIG_CMD_JFFS2
85 #define CONFIG_CMD_NET
86
87 #undef CONFIG_CMD_LOADS
88 #undef CONFIG_CMD_LOADB
89
90
91 /*
92 * Low Level Configuration Settings
93 * (address mappings, register initial values, etc.)
94 * You should know what you are doing if you make changes here.
95 */
96
97 /*
98 * Configuration for environment, which occupies third sector in flash.
99 */
100 #ifndef CONFIG_MONITOR_IS_IN_RAM
101 #define CONFIG_ENV_ADDR 0xff820000
102 #define CONFIG_ENV_SECT_SIZE 0x10000
103 #define CONFIG_ENV_SIZE 0x2000
104 #define CONFIG_ENV_IS_IN_FLASH
105 #else /* CONFIG_MONITOR_IS_IN_RAM */
106 #define CONFIG_ENV_OFFSET 0x4000
107 #define CONFIG_ENV_SECT_SIZE 0x2000
108 #define CONFIG_ENV_IS_IN_FLASH
109 #endif /* !CONFIG_MONITOR_IS_IN_RAM */
110
111 #define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */
112
113 #define CONFIG_SYS_PROMPT "=> "
114 #define CONFIG_SYS_LONGHELP /* undef to save memory */
115
116 #if defined(CONFIG_CMD_KGDB)
117 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
118 #else
119 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
120 #endif
121
122 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
123 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */
124 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
125
126 #define CONFIG_SYS_LOAD_ADDR 0x00100000
127
128 #define CONFIG_SYS_MEMTEST_START 0x400
129 #define CONFIG_SYS_MEMTEST_END 0x380000
130
131 #define CONFIG_SYS_HZ (50000000 / 64)
132 #define CONFIG_SYS_CLK 100000000
133
134 #define CONFIG_SYS_MBAR 0x40000000 /* Register Base Addrs */
135
136 /*
137 * Ethernet
138 */
139 #define CONFIG_MCFFEC
140 #ifdef CONFIG_MCFFEC
141 # define CONFIG_MII 1
142 # define CONFIG_MII_INIT 1
143 # define CONFIG_SYS_DISCOVER_PHY
144 # define CONFIG_SYS_RX_ETH_BUFFER 8
145 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
146
147 # define CONFIG_SYS_FEC0_PINMUX 0
148 # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
149 # define MCFFEC_TOUT_LOOP 50000
150 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
151 # ifndef CONFIG_SYS_DISCOVER_PHY
152 # define FECDUPLEX FULL
153 # define FECSPEED _100BASET
154 # else
155 # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
156 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
157 # endif
158 # endif /* CONFIG_SYS_DISCOVER_PHY */
159 #endif
160
161 /*
162 * Definitions for initial stack pointer and data area (in DPRAM)
163 */
164 #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000
165 #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */
166 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
167 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
168
169 /*
170 * Start addresses for the final memory configuration
171 * (Set up by the startup code)
172 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
173 */
174 #define CONFIG_SYS_SDRAM_BASE 0x00000000
175 #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */
176 #define CONFIG_SYS_FLASH_BASE 0xff800000
177
178 #ifdef CONFIG_MONITOR_IS_IN_RAM
179 #define CONFIG_SYS_MONITOR_BASE 0x20000
180 #else /* !CONFIG_MONITOR_IS_IN_RAM */
181 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
182 #endif /* CONFIG_MONITOR_IS_IN_RAM */
183
184 #define CONFIG_SYS_MONITOR_LEN 0x20000
185 #define CONFIG_SYS_MALLOC_LEN (256 << 10)
186 #define CONFIG_SYS_BOOTPARAMS_LEN (64*1024)
187
188 /*
189 * For booting Linux, the board info and command line data
190 * have to be in the first 8 MB of memory, since this is
191 * the maximum mapped by the Linux kernel during initialization ??
192 */
193 #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
194
195 /* FLASH organization */
196 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
197 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* max number of sectors on one chip */
198 #define CONFIG_SYS_FLASH_ERASE_TOUT 1000
199
200 #define CONFIG_SYS_FLASH_SIZE 0x800000
201 /*
202 * #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
203 */
204
205 /* Cache Configuration */
206 #define CONFIG_SYS_CACHELINE_SIZE 16
207
208 #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
209 CONFIG_SYS_INIT_RAM_SIZE - 8)
210 #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
211 CONFIG_SYS_INIT_RAM_SIZE - 4)
212 #define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI)
213 #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \
214 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
215 CF_ACR_EN | CF_ACR_SM_ALL)
216 #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \
217 CF_CACR_DISD | CF_CACR_INVI | \
218 CF_CACR_CEIB | CF_CACR_DCM | \
219 CF_CACR_EUSP)
220
221 /* Port configuration */
222 #define CONFIG_SYS_FECI2C 0xF0
223
224
225 /* Dynamic MTD partition support */
226 #define CONFIG_CMD_MTDPARTS
227 #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
228 #define CONFIG_FLASH_CFI_MTD
229 #define MTDIDS_DEFAULT "nor0=idmr-0"
230
231 #define MTDPARTS_DEFAULT "mtdparts=idmr-0:128k(u-boot)," \
232 "64k(env)," \
233 "640k(kernel)," \
234 "2m(rootfs)," \
235 "-(user)";
236
237 #if defined(CONFIG_CMD_MII)
238 #error "MII commands don't work on iDMR board and should not be enabled."
239 #endif
240
241 #endif /* _IDMR_H */