include/configs/ls1046a_common.h

   1 /* SPDX-License-Identifier: GPL-2.0+ */
   2 /*
   3  * Copyright 2016 Freescale Semiconductor
   4  * Copyright 2019-2021 NXP
   5  */
   6
   7 #ifndef __LS1046A_COMMON_H
   8 #define __LS1046A_COMMON_H
   9
  10 /* SPL build */
  11 #ifdef CONFIG_SPL_BUILD
  12 #define SPL_NO_QBMAN
  13 #define SPL_NO_FMAN
  14 #define SPL_NO_ENV
  15 #define SPL_NO_MISC
  16 #define SPL_NO_QSPI
  17 #define SPL_NO_USB
  18 #define SPL_NO_SATA
  19 #endif
  20 #if defined(CONFIG_SPL_BUILD) && \
  21         (defined(CONFIG_NAND_BOOT) || defined(CONFIG_QSPI_BOOT))
  22 #define SPL_NO_MMC
  23 #endif
  24 #if defined(CONFIG_SPL_BUILD)           && \
  25         !defined(CONFIG_SPL_FSL_LS_PPA)
  26 #define SPL_NO_IFC
  27 #endif
  28
  29 #include <asm/arch/config.h>
  30 #include <asm/arch/stream_id_lsch2.h>
  31
  32 /* Link Definitions */
  33 #ifdef CONFIG_TFABOOT
  34 #define CONFIG_SYS_INIT_SP_ADDR         CONFIG_SYS_TEXT_BASE
  35 #else
  36 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
  37 #endif
  38
  39 #define CONFIG_VERY_BIG_RAM
  40 #define CONFIG_SYS_DDR_SDRAM_BASE       0x80000000
  41 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY       0
  42 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_SDRAM_BASE
  43 #define CONFIG_SYS_DDR_BLOCK2_BASE      0x880000000ULL
  44
  45 #define CPU_RELEASE_ADDR               secondary_boot_addr
  46
  47 /* Generic Timer Definitions */
  48 #define COUNTER_FREQUENCY               25000000        /* 25MHz */
  49
  50 /* Serial Port */
  51 #define CONFIG_SYS_NS16550_SERIAL
  52 #define CONFIG_SYS_NS16550_REG_SIZE     1
  53 #define CONFIG_SYS_NS16550_CLK          (get_serial_clock())
  54
  55 /* SD boot SPL */
  56 #ifdef CONFIG_SD_BOOT
  57 #define CONFIG_SPL_MAX_SIZE             0x1f000         /* 124 KiB */
  58 #define CONFIG_SPL_STACK                0x10020000
  59 #define CONFIG_SPL_PAD_TO               0x21000         /* 132 KiB */
  60 #define CONFIG_SPL_BSS_START_ADDR       0x8f000000
  61 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
  62 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
  63                                         CONFIG_SPL_BSS_MAX_SIZE)
  64 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  65
  66 #ifdef CONFIG_NXP_ESBC
  67 #define CONFIG_U_BOOT_HDR_SIZE                          (16 << 10)
  68 /*
  69  * HDR would be appended at end of image and copied to DDR along
  70  * with U-Boot image. Here u-boot max. size is 512K. So if binary
  71  * size increases then increase this size in case of secure boot as
  72  * it uses raw u-boot image instead of fit image.
  73  */
  74 #define CONFIG_SYS_MONITOR_LEN          (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
  75 #else
  76 #define CONFIG_SYS_MONITOR_LEN          0x100000
  77 #endif /* ifdef CONFIG_NXP_ESBC */
  78 #endif
  79
  80 #if defined(CONFIG_QSPI_BOOT) && defined(CONFIG_SPL)
  81 #define CONFIG_SPL_TARGET               "spl/u-boot-spl.pbl"
  82 #define CONFIG_SPL_MAX_SIZE             0x1f000
  83 #define CONFIG_SPL_STACK                0x10020000
  84 #define CONFIG_SPL_PAD_TO               0x20000
  85 #define CONFIG_SPL_BSS_START_ADDR       0x8f000000
  86 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
  87 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
  88                                         CONFIG_SPL_BSS_MAX_SIZE)
  89 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
  90 #define CONFIG_SYS_MONITOR_LEN          0x100000
  91 #endif
  92
  93 /* NAND SPL */
  94 #ifdef CONFIG_NAND_BOOT
  95 #define CONFIG_SPL_PBL_PAD
  96
  97 #define CONFIG_SPL_MAX_SIZE             0x17000         /* 90 KiB */
  98 #define CONFIG_SPL_STACK                0x1001f000
  99 #define CONFIG_SYS_NAND_U_BOOT_DST      CONFIG_SYS_TEXT_BASE
 100 #define CONFIG_SYS_NAND_U_BOOT_START    CONFIG_SYS_TEXT_BASE
 101
 102 #define CONFIG_SPL_BSS_START_ADDR       0x8f000000
 103 #define CONFIG_SPL_BSS_MAX_SIZE         0x80000
 104 #define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
 105                                         CONFIG_SPL_BSS_MAX_SIZE)
 106 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x100000
 107 #define CONFIG_SYS_MONITOR_LEN          0xa0000
 108 #endif
 109
 110 /* GPIO */
 111
 112 /* I2C */
 113
 114 /* PCIe */
 115 #define CONFIG_PCIE1            /* PCIE controller 1 */
 116 #define CONFIG_PCIE2            /* PCIE controller 2 */
 117 #define CONFIG_PCIE3            /* PCIE controller 3 */
 118
 119 #ifdef CONFIG_PCI
 120 #define CONFIG_PCI_SCAN_SHOW
 121 #endif
 122
 123 /* SATA */
 124 #ifndef SPL_NO_SATA
 125 #define CONFIG_SCSI_AHCI_PLAT
 126
 127 #define CONFIG_SYS_SATA                         AHCI_BASE_ADDR
 128
 129 #define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
 130 #define CONFIG_SYS_SCSI_MAX_LUN                 1
 131 #define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
 132                                                 CONFIG_SYS_SCSI_MAX_LUN)
 133 #endif
 134
 135 /* FMan ucode */
 136 #ifndef SPL_NO_FMAN
 137 #define CONFIG_SYS_DPAA_FMAN
 138 #ifdef CONFIG_SYS_DPAA_FMAN
 139 #define CONFIG_SYS_FM_MURAM_SIZE        0x60000
 140 #endif
 141 #define CONFIG_SYS_FDT_PAD              (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
 142 #endif
 143
 144 /* Miscellaneous configurable options */
 145
 146 #define CONFIG_HWCONFIG
 147 #define HWCONFIG_BUFFER_SIZE            128
 148
 149 #ifndef CONFIG_SPL_BUILD
 150 #define BOOT_TARGET_DEVICES(func) \
 151         func(SCSI, scsi, 0) \
 152         func(MMC, mmc, 0) \
 153         func(USB, usb, 0) \
 154         func(DHCP, dhcp, na)
 155 #include <config_distro_bootcmd.h>
 156 #endif
 157
 158 #if defined(CONFIG_TARGET_LS1046AFRWY)
 159 #define LS1046A_BOOT_SRC_AND_HDR\
 160         "boot_scripts=ls1046afrwy_boot.scr\0"   \
 161         "boot_script_hdr=hdr_ls1046afrwy_bs.out\0"
 162 #elif defined(CONFIG_TARGET_LS1046AQDS)
 163 #define LS1046A_BOOT_SRC_AND_HDR\
 164         "boot_scripts=ls1046aqds_boot.scr\0"    \
 165         "boot_script_hdr=hdr_ls1046aqds_bs.out\0"
 166 #else
 167 #define LS1046A_BOOT_SRC_AND_HDR\
 168         "boot_scripts=ls1046ardb_boot.scr\0"    \
 169         "boot_script_hdr=hdr_ls1046ardb_bs.out\0"
 170 #endif
 171 #ifndef SPL_NO_MISC
 172 /* Initial environment variables */
 173 #define CONFIG_EXTRA_ENV_SETTINGS               \
 174         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 175         "ramdisk_addr=0x800000\0"               \
 176         "ramdisk_size=0x2000000\0"              \
 177         "bootm_size=0x10000000\0"               \
 178         "fdt_addr=0x64f00000\0"                 \
 179         "kernel_addr=0x61000000\0"              \
 180         "scriptaddr=0x80000000\0"               \
 181         "scripthdraddr=0x80080000\0"            \
 182         "fdtheader_addr_r=0x80100000\0"         \
 183         "kernelheader_addr_r=0x80200000\0"      \
 184         "load_addr=0xa0000000\0"            \
 185         "kernel_addr_r=0x81000000\0"            \
 186         "fdt_addr_r=0x90000000\0"               \
 187         "ramdisk_addr_r=0xa0000000\0"           \
 188         "kernel_start=0x1000000\0"              \
 189         "kernelheader_start=0x600000\0"         \
 190         "kernel_load=0xa0000000\0"              \
 191         "kernel_size=0x2800000\0"               \
 192         "kernelheader_size=0x40000\0"           \
 193         "kernel_addr_sd=0x8000\0"               \
 194         "kernel_size_sd=0x14000\0"              \
 195         "kernelhdr_addr_sd=0x3000\0"            \
 196         "kernelhdr_size_sd=0x10\0"              \
 197         "console=ttyS0,115200\0"                \
 198          CONFIG_MTDPARTS_DEFAULT "\0"           \
 199         BOOTENV                                 \
 200         LS1046A_BOOT_SRC_AND_HDR                \
 201         "scan_dev_for_boot_part="               \
 202                 "part list ${devtype} ${devnum} devplist; "   \
 203                 "env exists devplist || setenv devplist 1; "  \
 204                 "for distro_bootpart in ${devplist}; do "     \
 205                   "if fstype ${devtype} "                  \
 206                         "${devnum}:${distro_bootpart} "      \
 207                         "bootfstype; then "                  \
 208                         "run scan_dev_for_boot; "            \
 209                   "fi; "                                   \
 210                 "done\0"                                   \
 211         "boot_a_script="                                  \
 212                 "load ${devtype} ${devnum}:${distro_bootpart} "  \
 213                         "${scriptaddr} ${prefix}${script}; "    \
 214                 "env exists secureboot && load ${devtype} "     \
 215                         "${devnum}:${distro_bootpart} "         \
 216                         "${scripthdraddr} ${prefix}${boot_script_hdr}; " \
 217                         "env exists secureboot "        \
 218                         "&& esbc_validate ${scripthdraddr};"    \
 219                 "source ${scriptaddr}\0"          \
 220         "qspi_bootcmd=echo Trying load from qspi..;"      \
 221                 "sf probe && sf read $load_addr "         \
 222                 "$kernel_start $kernel_size; env exists secureboot "    \
 223                 "&& sf read $kernelheader_addr_r $kernelheader_start "  \
 224                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 225                 "bootm $load_addr#$board\0"             \
 226         "nand_bootcmd=echo Trying load from nand..;"      \
 227                 "nand info; nand read $load_addr "         \
 228                 "$kernel_start $kernel_size; env exists secureboot "    \
 229                 "&& nand read $kernelheader_addr_r $kernelheader_start " \
 230                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 231                 "bootm $load_addr#$board\0"             \
 232         "nor_bootcmd=echo Trying load from nor..;"      \
 233                 "cp.b $kernel_addr $load_addr "         \
 234                 "$kernel_size; env exists secureboot "  \
 235                 "&& cp.b $kernelheader_addr $kernelheader_addr_r "      \
 236                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; " \
 237                 "bootm $load_addr#$board\0"     \
 238         "sd_bootcmd=echo Trying load from SD ..;"       \
 239                 "mmcinfo; mmc read $load_addr "         \
 240                 "$kernel_addr_sd $kernel_size_sd && "   \
 241                 "env exists secureboot && mmc read $kernelheader_addr_r "               \
 242                 "$kernelhdr_addr_sd $kernelhdr_size_sd "                \
 243                 " && esbc_validate ${kernelheader_addr_r};"     \
 244                 "bootm $load_addr#$board\0"
 245
 246 #endif
 247
 248 /* Monitor Command Prompt */
 249 #define CONFIG_SYS_CBSIZE               512     /* Console I/O Buffer Size */
 250
 251 #define CONFIG_SYS_MAXARGS              64      /* max command args */
 252
 253 #define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */
 254
 255 #include <asm/arch/soc.h>
 256
 257 #endif /* __LS1046A_COMMON_H */