include/configs/nitrogen6x.h

   1 /*
   2  * Copyright (C) 2010-2011 Freescale Semiconductor, Inc.
   3  *
   4  * Configuration settings for the Boundary Devices Nitrogen6X
   5  * and Freescale i.MX6Q Sabre Lite boards.
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __CONFIG_H
  11 #define __CONFIG_H
  12
  13 #include "mx6_common.h"
  14 #define CONFIG_MX6
  15 #define CONFIG_DISPLAY_CPUINFO
  16 #define CONFIG_DISPLAY_BOARDINFO
  17
  18 #define CONFIG_MACH_TYPE        3769
  19
  20 #include <asm/arch/imx-regs.h>
  21 #include <asm/imx-common/gpio.h>
  22
  23 #define CONFIG_CMDLINE_TAG
  24 #define CONFIG_SETUP_MEMORY_TAGS
  25 #define CONFIG_INITRD_TAG
  26 #define CONFIG_REVISION_TAG
  27 #define CONFIG_SYS_GENERIC_BOARD
  28
  29 /* Size of malloc() pool */
  30 #define CONFIG_SYS_MALLOC_LEN           (10 * 1024 * 1024)
  31
  32 #define CONFIG_BOARD_EARLY_INIT_F
  33 #define CONFIG_MISC_INIT_R
  34 #define CONFIG_MXC_GPIO
  35 #define CONFIG_CMD_GPIO
  36 #define CONFIG_CI_UDC
  37 #define CONFIG_USBD_HS
  38 #define CONFIG_USB_GADGET_DUALSPEED
  39 #define CONFIG_USB_ETHER
  40 #define CONFIG_USB_ETH_CDC
  41 #define CONFIG_NETCONSOLE
  42
  43 #define CONFIG_CMD_FUSE
  44 #ifdef CONFIG_CMD_FUSE
  45 #define CONFIG_MXC_OCOTP
  46 #endif
  47
  48 #define CONFIG_MXC_UART
  49 #define CONFIG_MXC_UART_BASE           UART2_BASE
  50
  51 #define CONFIG_CMD_SF
  52 #ifdef CONFIG_CMD_SF
  53 #define CONFIG_SPI_FLASH
  54 #define CONFIG_SPI_FLASH_SST
  55 #define CONFIG_MXC_SPI
  56 #define CONFIG_SF_DEFAULT_BUS  0
  57 #define CONFIG_SF_DEFAULT_CS   0
  58 #define CONFIG_SF_DEFAULT_SPEED 25000000
  59 #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
  60 #endif
  61
  62 /* I2C Configs */
  63 #define CONFIG_CMD_I2C
  64 #define CONFIG_SYS_I2C
  65 #define CONFIG_SYS_I2C_MXC
  66 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  67 #define CONFIG_SYS_I2C_SPEED            100000
  68 #define CONFIG_I2C_EDID
  69
  70 /* MMC Configs */
  71 #define CONFIG_FSL_ESDHC
  72 #define CONFIG_FSL_USDHC
  73 #define CONFIG_SYS_FSL_ESDHC_ADDR      0
  74 #define CONFIG_SYS_FSL_USDHC_NUM       2
  75
  76 #define CONFIG_MMC
  77 #define CONFIG_CMD_MMC
  78 #define CONFIG_GENERIC_MMC
  79 #define CONFIG_BOUNCE_BUFFER
  80 #define CONFIG_CMD_EXT2
  81 #define CONFIG_CMD_EXT4
  82 #define CONFIG_CMD_EXT4_WRITE
  83 #define CONFIG_CMD_FAT
  84 #define CONFIG_DOS_PARTITION
  85
  86 #ifdef CONFIG_MX6Q
  87 #define CONFIG_CMD_SATA
  88 #endif
  89
  90 /*
  91  * SATA Configs
  92  */
  93 #ifdef CONFIG_CMD_SATA
  94 #define CONFIG_DWC_AHSATA
  95 #define CONFIG_SYS_SATA_MAX_DEVICE      1
  96 #define CONFIG_DWC_AHSATA_PORT_ID       0
  97 #define CONFIG_DWC_AHSATA_BASE_ADDR     SATA_ARB_BASE_ADDR
  98 #define CONFIG_LBA48
  99 #define CONFIG_LIBATA
 100 #endif
 101
 102 #define CONFIG_CMD_PING
 103 #define CONFIG_CMD_DHCP
 104 #define CONFIG_CMD_MII
 105 #define CONFIG_CMD_NET
 106 #define CONFIG_FEC_MXC
 107 #define CONFIG_MII
 108 #define IMX_FEC_BASE                    ENET_BASE_ADDR
 109 #define CONFIG_FEC_XCV_TYPE             RGMII
 110 #define CONFIG_ETHPRIME                 "FEC"
 111 #define CONFIG_FEC_MXC_PHYADDR          6
 112 #define CONFIG_PHYLIB
 113 #define CONFIG_PHY_MICREL
 114 #define CONFIG_PHY_MICREL_KSZ9021
 115
 116 /* USB Configs */
 117 #define CONFIG_CMD_USB
 118 #define CONFIG_CMD_FAT
 119 #define CONFIG_USB_EHCI
 120 #define CONFIG_USB_EHCI_MX6
 121 #define CONFIG_USB_STORAGE
 122 #define CONFIG_USB_HOST_ETHER
 123 #define CONFIG_USB_ETHER_ASIX
 124 #define CONFIG_USB_ETHER_MCS7830
 125 #define CONFIG_USB_ETHER_SMSC95XX
 126 #define CONFIG_USB_MAX_CONTROLLER_COUNT 2
 127 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET        /* For OTG port */
 128 #define CONFIG_MXC_USB_PORTSC   (PORT_PTS_UTMI | PORT_PTS_PTW)
 129 #define CONFIG_MXC_USB_FLAGS    0
 130 #define CONFIG_USB_KEYBOARD
 131 #define CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP
 132
 133 /* Miscellaneous commands */
 134 #define CONFIG_CMD_BMODE
 135 #define CONFIG_CMD_SETEXPR
 136
 137 /* Framebuffer and LCD */
 138 #define CONFIG_VIDEO
 139 #define CONFIG_VIDEO_IPUV3
 140 #define CONFIG_CFB_CONSOLE
 141 #define CONFIG_VGA_AS_SINGLE_DEVICE
 142 #define CONFIG_SYS_CONSOLE_IS_IN_ENV
 143 #define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
 144 #define CONFIG_VIDEO_BMP_RLE8
 145 #define CONFIG_SPLASH_SCREEN
 146 #define CONFIG_SPLASH_SCREEN_ALIGN
 147 #define CONFIG_VIDEO_BMP_GZIP
 148 #define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (6 * 1024 * 1024)
 149 #define CONFIG_BMP_16BPP
 150 #define CONFIG_IPUV3_CLK 260000000
 151 #define CONFIG_CMD_HDMIDETECT
 152 #define CONFIG_CONSOLE_MUX
 153 #define CONFIG_IMX_HDMI
 154 #define CONFIG_IMX_VIDEO_SKIP
 155
 156 /* allow to overwrite serial and ethaddr */
 157 #define CONFIG_ENV_OVERWRITE
 158 #define CONFIG_CONS_INDEX              1
 159 #define CONFIG_BAUDRATE                        115200
 160
 161 /* Command definition */
 162 #include <config_cmd_default.h>
 163
 164 #undef CONFIG_CMD_IMLS
 165
 166 #define CONFIG_BOOTDELAY               1
 167
 168 #define CONFIG_PREBOOT                 ""
 169
 170 #define CONFIG_LOADADDR                        0x12000000
 171 #define CONFIG_SYS_TEXT_BASE           0x17800000
 172
 173 #ifdef CONFIG_CMD_SATA
 174 #define CONFIG_DRIVE_SATA "sata "
 175 #else
 176 #define CONFIG_DRIVE_SATA
 177 #endif
 178
 179 #ifdef CONFIG_CMD_MMC
 180 #define CONFIG_DRIVE_MMC "mmc "
 181 #else
 182 #define CONFIG_DRIVE_MMC
 183 #endif
 184
 185 #ifdef CONFIG_USB_STORAGE
 186 #define CONFIG_DRIVE_USB "usb "
 187 #else
 188 #define CONFIG_DRIVE_USB
 189 #endif
 190
 191 #define CONFIG_DRIVE_TYPES CONFIG_DRIVE_SATA CONFIG_DRIVE_MMC CONFIG_DRIVE_USB
 192 #define CONFIG_UMSDEVS CONFIG_DRIVE_SATA CONFIG_DRIVE_MMC
 193
 194 #if defined(CONFIG_SABRELITE)
 195 #define CONFIG_EXTRA_ENV_SETTINGS \
 196         "script=boot.scr\0" \
 197         "uimage=uImage\0" \
 198         "console=ttymxc1\0" \
 199         "fdt_high=0xffffffff\0" \
 200         "initrd_high=0xffffffff\0" \
 201         "fdt_file=imx6q-sabrelite.dtb\0" \
 202         "fdt_addr=0x18000000\0" \
 203         "boot_fdt=try\0" \
 204         "ip_dyn=yes\0" \
 205         "mmcdevs=0 1\0" \
 206         "mmcpart=1\0" \
 207         "mmcroot=/dev/mmcblk0p2 rootwait rw\0" \
 208         "mmcargs=setenv bootargs console=${console},${baudrate} " \
 209                 "root=${mmcroot}\0" \
 210         "loadbootscript=" \
 211                 "load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 212         "bootscript=echo Running bootscript from mmc ...; " \
 213                 "source\0" \
 214         "loaduimage=load mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \
 215         "loadfdt=load mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 216         "mmcboot=echo Booting from mmc ...; " \
 217                 "run mmcargs; " \
 218                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 219                         "if run loadfdt; then " \
 220                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 221                         "else " \
 222                                 "if test ${boot_fdt} = try; then " \
 223                                         "bootm; " \
 224                                 "else " \
 225                                         "echo WARN: Cannot load the DT; " \
 226                                 "fi; " \
 227                         "fi; " \
 228                 "else " \
 229                         "bootm; " \
 230                 "fi;\0" \
 231         "netargs=setenv bootargs console=${console},${baudrate} " \
 232                 "root=/dev/nfs " \
 233         "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 234                 "netboot=echo Booting from net ...; " \
 235                 "run netargs; " \
 236                 "if test ${ip_dyn} = yes; then " \
 237                         "setenv get_cmd dhcp; " \
 238                 "else " \
 239                         "setenv get_cmd tftp; " \
 240                 "fi; " \
 241                 "${get_cmd} ${uimage}; " \
 242                 "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 243                         "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 244                                 "bootm ${loadaddr} - ${fdt_addr}; " \
 245                         "else " \
 246                                 "if test ${boot_fdt} = try; then " \
 247                                         "bootm; " \
 248                                 "else " \
 249                                         "echo WARN: Cannot load the DT; " \
 250                                 "fi; " \
 251                         "fi; " \
 252                 "else " \
 253                         "bootm; " \
 254                 "fi;\0"
 255
 256 #define CONFIG_BOOTCOMMAND \
 257         "for mmcdev in ${mmcdevs}; do " \
 258                 "mmc dev ${mmcdev}; " \
 259                 "if mmc rescan; then " \
 260                         "if run loadbootscript; then " \
 261                                 "run bootscript; " \
 262                         "else " \
 263                                 "if run loaduimage; then " \
 264                                         "run mmcboot; " \
 265                                 "fi; " \
 266                         "fi; " \
 267                 "fi; " \
 268         "done; " \
 269         "run netboot; "
 270 #else
 271 #define CONFIG_EXTRA_ENV_SETTINGS \
 272         "bootdevs=" CONFIG_DRIVE_TYPES "\0" \
 273         "umsdevs=" CONFIG_UMSDEVS "\0" \
 274         "console=ttymxc1\0" \
 275         "clearenv=if sf probe || sf probe || sf probe 1 ; then " \
 276                 "sf erase 0xc0000 0x2000 && " \
 277                 "echo restored environment to factory default ; fi\0" \
 278         "bootcmd=for dtype in ${bootdevs}" \
 279                 "; do " \
 280                         "if itest.s \"xusb\" == \"x${dtype}\" ; then " \
 281                                 "usb start ;" \
 282                         "fi; " \
 283                         "for disk in 0 1 ; do ${dtype} dev ${disk} ;" \
 284                                 "load " \
 285                                         "${dtype} ${disk}:1 " \
 286                                         "10008000 " \
 287                                         "/6x_bootscript" \
 288                                         "&& source 10008000 ; " \
 289                         "done ; " \
 290                 "done; " \
 291                 "setenv stdout serial,vga ; " \
 292                 "echo ; echo 6x_bootscript not found ; " \
 293                 "echo ; echo serial console at 115200, 8N1 ; echo ; " \
 294                 "echo details at http://boundarydevices.com/6q_bootscript ; " \
 295                 "setenv stdout serial;" \
 296                 "setenv stdin serial,usbkbd;" \
 297                 "for dtype in ${umsdevs} ; do " \
 298                         "if itest.s sata == ${dtype}; then " \
 299                                 "initcmd='sata init' ;" \
 300                         "else " \
 301                                 "initcmd='mmc rescan' ;" \
 302                         "fi; " \
 303                         "for disk in 0 1 ; do " \
 304                                 "if $initcmd && $dtype dev $disk ; then " \
 305                                         "setenv stdout serial,vga; " \
 306                                         "echo expose ${dtype} ${disk} " \
 307                                                 "over USB; " \
 308                                         "ums 0 $dtype $disk ;" \
 309                                 "fi; " \
 310                 "       done; " \
 311                 "done ;" \
 312                 "setenv stdout serial,vga; " \
 313                 "echo no block devices found;" \
 314                 "\0" \
 315         "initrd_high=0xffffffff\0" \
 316         "upgradeu=for dtype in ${bootdevs}" \
 317                 "; do " \
 318                 "for disk in 0 1 ; do ${dtype} dev ${disk} ;" \
 319                         "load ${dtype} ${disk}:1 10008000 " \
 320                                 "/6x_upgrade " \
 321                                 "&& source 10008000 ; " \
 322                 "done ; " \
 323         "done\0" \
 324
 325 #endif
 326 /* Miscellaneous configurable options */
 327 #define CONFIG_SYS_LONGHELP
 328 #define CONFIG_SYS_HUSH_PARSER
 329 #define CONFIG_SYS_PROMPT              "U-Boot > "
 330 #define CONFIG_AUTO_COMPLETE
 331 #define CONFIG_SYS_CBSIZE              1024
 332 #define CONFIG_SYS_MAXARGS             48
 333 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 334
 335 #define CONFIG_SYS_MEMTEST_START       0x10000000
 336 #define CONFIG_SYS_MEMTEST_END         0x10010000
 337 #define CONFIG_SYS_MEMTEST_SCRATCH     0x10800000
 338
 339 #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR
 340
 341 #define CONFIG_CMDLINE_EDITING
 342
 343 /* Physical Memory Map */
 344 #define CONFIG_NR_DRAM_BANKS           1
 345 #define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR
 346
 347 #define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
 348 #define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
 349 #define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE
 350
 351 #define CONFIG_SYS_INIT_SP_OFFSET \
 352         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 353 #define CONFIG_SYS_INIT_SP_ADDR \
 354         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 355
 356 /* FLASH and environment organization */
 357 #define CONFIG_SYS_NO_FLASH
 358
 359 #define CONFIG_ENV_SIZE                 (8 * 1024)
 360
 361 #if defined(CONFIG_SABRELITE)
 362 #define CONFIG_ENV_IS_IN_MMC
 363 #else
 364 #define CONFIG_ENV_IS_IN_SPI_FLASH
 365 #endif
 366
 367 #if defined(CONFIG_ENV_IS_IN_MMC)
 368 #define CONFIG_ENV_OFFSET               (6 * 64 * 1024)
 369 #define CONFIG_SYS_MMC_ENV_DEV          0
 370 #elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
 371 #define CONFIG_ENV_OFFSET               (768 * 1024)
 372 #define CONFIG_ENV_SECT_SIZE            (8 * 1024)
 373 #define CONFIG_ENV_SPI_BUS              CONFIG_SF_DEFAULT_BUS
 374 #define CONFIG_ENV_SPI_CS               CONFIG_SF_DEFAULT_CS
 375 #define CONFIG_ENV_SPI_MODE             CONFIG_SF_DEFAULT_MODE
 376 #define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
 377 #endif
 378
 379 #define CONFIG_OF_LIBFDT
 380 #define CONFIG_CMD_BOOTZ
 381
 382 #ifndef CONFIG_SYS_DCACHE_OFF
 383 #define CONFIG_CMD_CACHE
 384 #endif
 385
 386 #define CONFIG_CMD_BMP
 387
 388 #define CONFIG_CMD_TIME
 389 #define CONFIG_CMD_MEMTEST
 390 #define CONFIG_SYS_ALT_MEMTEST
 391
 392 #define CONFIG_CMD_BOOTZ
 393 #define CONFIG_SUPPORT_RAW_INITRD
 394 #define CONFIG_CMD_FS_GENERIC
 395
 396 /*
 397  * PCI express
 398  */
 399 #ifdef CONFIG_CMD_PCI
 400 #define CONFIG_PCI
 401 #define CONFIG_PCI_PNP
 402 #define CONFIG_PCI_SCAN_SHOW
 403 #define CONFIG_PCIE_IMX
 404 #endif
 405
 406 #define CONFIG_CMD_ELF
 407
 408 #define CONFIG_USB_GADGET
 409 #define CONFIG_CMD_USB_MASS_STORAGE
 410 #define CONFIG_USB_GADGET_MASS_STORAGE
 411 #define CONFIG_USBDOWNLOAD_GADGET
 412 #define CONFIG_USB_GADGET_VBUS_DRAW     2
 413
 414 /* Netchip IDs */
 415 #define CONFIG_G_DNL_VENDOR_NUM 0x0525
 416 #define CONFIG_G_DNL_PRODUCT_NUM 0xa4a5
 417 #define CONFIG_G_DNL_MANUFACTURER "Boundary"
 418
 419 #define CONFIG_CMD_FASTBOOT
 420 #define CONFIG_ANDROID_BOOT_IMAGE
 421 #define CONFIG_USB_FASTBOOT_BUF_ADDR   CONFIG_SYS_LOAD_ADDR
 422 #define CONFIG_USB_FASTBOOT_BUF_SIZE   0x07000000
 423
 424 #endif         /* __CONFIG_H */