include/configs/omap3_sdp3430.h

   1 /*
   2  * (C) Copyright 2006-2009
   3  * Texas Instruments Incorporated.
   4  * Richard Woodruff <r-woodruff2@ti.com>
   5  * Syed Mohammed Khasim <x0khasim@ti.com>
   6  * Nishanth Menon <nm@ti.com>
   7  *
   8  * Configuration settings for the 3430 TI SDP3430 board.
   9  *
  10  * See file CREDITS for list of people who contributed to this
  11  * project.
  12  *
  13  * This program is free software; you can redistribute it and/or
  14  * modify it under the terms of the GNU General Public License as
  15  * published by the Free Software Foundation; either version 2 of
  16  * the License, or (at your option) any later version.
  17  *
  18  * This program is distributed in the hope that it will be useful,
  19  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  20  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  21  * GNU General Public License for more details.
  22  *
  23  * You should have received a copy of the GNU General Public License
  24  * along with this program; if not, write to the Free Software
  25  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  26  * MA 02111-1307 USA
  27  */
  28
  29 #ifndef __CONFIG_H
  30 #define __CONFIG_H
  31
  32 /* TODO: REMOVE THE FOLLOWING
  33  * Retained the following till size.h is removed in u-boot
  34  */
  35 #include <asm/sizes.h>
  36 /*
  37  * High Level Configuration Options
  38  */
  39 #define CONFIG_ARMV7            1       /* This is an ARM V7 CPU core */
  40 #define CONFIG_OMAP             1       /* in a TI OMAP core */
  41 #define CONFIG_OMAP34XX         1       /* which is a 34XX */
  42 #define CONFIG_OMAP3430         1       /* which is in a 3430 */
  43 #define CONFIG_OMAP3_3430SDP    1       /* working with SDP Rev2 */
  44
  45 #define CONFIG_SDRC     /* The chip has SDRC controller */
  46
  47 #include <asm/arch/cpu.h>               /* get chip and board defs */
  48 #include <asm/arch/omap3.h>
  49
  50 /*
  51  * NOTE:  these #defines presume standard SDP jumper settings.
  52  * In particular:
  53  *  - 26 MHz clock (not 19.2 or 38.4 MHz)
  54  *  - Boot from 128MB NOR, not NAND or OneNAND
  55  *
  56  * At this writing, OMAP3 U-Boot support doesn't permit concurrent
  57  * support for all the flash types the board supports.
  58  */
  59 #define CONFIG_DISPLAY_CPUINFO          1
  60 #define CONFIG_DISPLAY_BOARDINFO        1
  61
  62 /* Clock Defines */
  63 #define V_OSCK                  26000000        /* Clock output from T2 */
  64 #define V_SCLK                  (V_OSCK >> 1)
  65
  66 #undef CONFIG_USE_IRQ                   /* no support for IRQs */
  67 #define CONFIG_MISC_INIT_R
  68
  69 #define CONFIG_CMDLINE_TAG              1       /* enable passing of ATAGs */
  70 #define CONFIG_SETUP_MEMORY_TAGS        1
  71 #define CONFIG_INITRD_TAG               1
  72 #define CONFIG_REVISION_TAG             1
  73
  74 #define CONFIG_OF_LIBFDT                1
  75
  76 /*
  77  * Size of malloc() pool
  78  * Total Size Environment - 256k
  79  * Malloc - add 256k
  80  */
  81 #define CONFIG_ENV_SIZE                 (256 << 10)
  82 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + (256 << 10))
  83                                                 /* initial data */
  84
  85 /*--------------------------------------------------------------------------*/
  86
  87 /*
  88  * Hardware drivers
  89  */
  90
  91 /*
  92  * TWL4030
  93  */
  94 #define CONFIG_TWL4030_POWER            1
  95
  96 /*
  97  * serial port - NS16550 compatible
  98  */
  99 #define V_NS16550_CLK                   48000000        /* 48MHz (APLL96/2) */
 100
 101 #define CONFIG_SYS_NS16550
 102 #define CONFIG_SYS_NS16550_SERIAL
 103 #define CONFIG_SYS_NS16550_REG_SIZE     (-4)
 104 #define CONFIG_SYS_NS16550_CLK          V_NS16550_CLK
 105
 106 /* Original SDP u-boot used UART1 and thus J8 (innermost); that can be
 107  * swapped with UART2 via jumpering.  Downsides of using J8:  it doesn't
 108  * support UART boot (that's only for UART3); it prevents sharing a Linux
 109  * kernel (LL_DEBUG_UART3) or filesystem (getty ttyS2) with most boards.
 110  *
 111  * UART boot uses UART3 on J9, and the SDP user's guide says to use
 112  * that for console.  Downsides of using J9:  you can't use IRDA too;
 113  * since UART3 isn't in the CORE power domain, it may be a bit less
 114  * usable in certain PM-sensitive debug scenarios.
 115  */
 116 #undef CONSOLE_J9                       /* else J8/UART1 (innermost) */
 117
 118 #ifdef CONSOLE_J9
 119 #define CONFIG_CONS_INDEX               3
 120 #define CONFIG_SYS_NS16550_COM3         OMAP34XX_UART3
 121 #define CONFIG_SERIAL3                  3       /* UART3 */
 122 #else
 123 #define CONFIG_CONS_INDEX               1
 124 #define CONFIG_SYS_NS16550_COM1         OMAP34XX_UART1
 125 #define CONFIG_SERIAL1                  1       /* UART1 */
 126 #endif
 127
 128 #define CONFIG_ENV_OVERWRITE
 129 #define CONFIG_BAUDRATE                 115200
 130 #define CONFIG_SYS_BAUDRATE_TABLE       {4800, 9600, 19200, 38400, 57600,\
 131                                         115200}
 132
 133 /*
 134  * I2C for power management setup
 135  */
 136 #define CONFIG_HARD_I2C                 1
 137 #define CONFIG_SYS_I2C_SPEED            100000
 138 #define CONFIG_SYS_I2C_SLAVE            1
 139 #define CONFIG_SYS_I2C_BUS              0
 140 #define CONFIG_SYS_I2C_BUS_SELECT       1
 141 #define CONFIG_DRIVER_OMAP34XX_I2C      1
 142
 143 /* DDR - I use Infineon DDR */
 144 #define CONFIG_OMAP3_INFINEON_DDR       1
 145
 146 /* OMITTED:  single 1 Gbit MT29F1G NAND flash */
 147
 148 /*
 149  * NOR boot support - single 1 Gbit PF48F6000M0 Strataflash
 150  */
 151 #define CONFIG_SYS_FLASH_BASE           0x10000000
 152 #define CONFIG_FLASH_CFI_DRIVER         1       /* Use drivers/cfi_flash.c */
 153 #define CONFIG_SYS_FLASH_CFI            1       /* use CFI geometry data */
 154 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1     /* ~10x faster writes */
 155 #define CONFIG_SYS_FLASH_PROTECTION     1       /* hardware sector protection */
 156 #define CONFIG_SYS_FLASH_EMPTY_INFO     1       /* flinfo 'E' for empty */
 157 #define CONFIG_SYS_FLASH_BANKS_LIST     {CONFIG_SYS_FLASH_BASE}
 158 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max number of flash banks */
 159
 160 #define CONFIG_SYS_FLASH_CFI_WIDTH      2
 161 #define PHYS_FLASH_SIZE                 (128 << 20)
 162 #define CONFIG_SYS_MAX_FLASH_SECT       512     /* max sectors on one chip */
 163
 164 /* OMITTED:  single 2 Gbit KFM2G16 OneNAND flash */
 165
 166 #define CONFIG_ENV_IS_IN_FLASH          1
 167 #define CONFIG_SYS_ENV_SECT_SIZE        (256 << 10)
 168 #define CONFIG_ENV_OFFSET               CONFIG_SYS_ENV_SECT_SIZE
 169 #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_ENV_SECT_SIZE)
 170 /*--------------------------------------------------------------------------*/
 171
 172 /* commands to include */
 173 #include <config_cmd_default.h>
 174
 175 /* Enabled commands */
 176 #define CONFIG_CMD_DHCP         /* DHCP Support                 */
 177 #define CONFIG_CMD_EXT2         /* EXT2 Support                 */
 178 #define CONFIG_CMD_FAT          /* FAT support                  */
 179 #define CONFIG_CMD_I2C          /* I2C serial bus support       */
 180 #define CONFIG_CMD_JFFS2        /* JFFS2 Support                */
 181 #define CONFIG_CMD_MMC          /* MMC support                  */
 182 #define CONFIG_CMD_NET
 183
 184 /* Disabled commands */
 185 #undef CONFIG_CMD_FPGA          /* FPGA configuration Support   */
 186 #undef CONFIG_CMD_IMLS          /* List all found images        */
 187
 188 /*--------------------------------------------------------------------------*/
 189 /*
 190  * MMC boot support
 191  */
 192
 193 #if defined(CONFIG_CMD_MMC)
 194 #define CONFIG_MMC                      1
 195 #define CONFIG_OMAP3_MMC                1
 196 #define CONFIG_DOS_PARTITION            1
 197 #endif
 198
 199 /*----------------------------------------------------------------------------
 200  * SMSC9115 Ethernet from SMSC9118 family
 201  *----------------------------------------------------------------------------
 202  */
 203 #if defined(CONFIG_CMD_NET)
 204
 205 #define CONFIG_NET_MULTI
 206 #define CONFIG_LAN91C96
 207 #define CONFIG_LAN91C96_BASE    DEBUG_BASE
 208 #define CONFIG_LAN91C96_EXT_PHY
 209
 210 #define CONFIG_BOOTP_SEND_HOSTNAME
 211 /*
 212  * BOOTP fields
 213  */
 214 #define CONFIG_BOOTP_SUBNETMASK         0x00000001
 215 #define CONFIG_BOOTP_GATEWAY            0x00000002
 216 #define CONFIG_BOOTP_HOSTNAME           0x00000004
 217 #define CONFIG_BOOTP_BOOTPATH           0x00000010
 218 #endif /* (CONFIG_CMD_NET) */
 219
 220 /*
 221  * Environment setup
 222  *
 223  * Default boot order:  mmc bootscript, MMC uImage, NOR image.
 224  * Network booting environment must be configured at site.
 225  */
 226
 227 /* allow overwriting serial config and ethaddr */
 228 #define CONFIG_ENV_OVERWRITE
 229
 230 #define CONFIG_EXTRA_ENV_SETTINGS \
 231         "loadaddr=0x82000000\0" \
 232         "console=ttyS0,115200n8\0" \
 233         "mmcargs=setenv bootargs console=${console} " \
 234                 "root=/dev/mmcblk0p2 rw " \
 235                 "rootfstype=ext3 rootwait\0" \
 236         "norargs=setenv bootargs console=${console} " \
 237                 "root=/dev/mtdblock3 rw " \
 238                 "rootfstype=jffs2\0" \
 239         "loadbootscript=fatload mmc 0 ${loadaddr} boot.scr\0" \
 240         "bootscript=echo Running bootscript from MMC/SD ...; " \
 241                 "autoscr ${loadaddr}\0" \
 242         "loaduimage=fatload mmc 0 ${loadaddr} uImage\0" \
 243         "mmcboot=echo Booting from MMC/SD ...; " \
 244                 "run mmcargs; " \
 245                 "bootm ${loadaddr}\0" \
 246         "norboot=echo Booting from NOR ...; " \
 247                 "run norargs; " \
 248                 "bootm 0x80000\0" \
 249
 250 #define CONFIG_BOOTCOMMAND \
 251         "if mmcinit; then " \
 252                 "if run loadbootscript; then " \
 253                         "run bootscript; " \
 254                 "else " \
 255                         "if run loaduimage; then " \
 256                                 "run mmcboot; " \
 257                         "else run norboot; " \
 258                         "fi; " \
 259                 "fi; " \
 260         "else run norboot; fi"
 261
 262 #define CONFIG_AUTO_COMPLETE            1
 263
 264 /*--------------------------------------------------------------------------*/
 265
 266 /*
 267  * Miscellaneous configurable options
 268  */
 269
 270 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 271 #define CONFIG_SYS_HUSH_PARSER          /* use "hush" command parser */
 272 #define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
 273 #define CONFIG_SYS_PROMPT               "OMAP34XX SDP # "
 274 #define CONFIG_SYS_CBSIZE               256     /* Console I/O Buffer Size */
 275 /* Print Buffer Size */
 276 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 277                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 278 #define CONFIG_SYS_MAXARGS              16      /* max number of command args */
 279 /* Boot Argument Buffer Size */
 280 #define CONFIG_SYS_BARGSIZE             (CONFIG_SYS_CBSIZE)
 281
 282 /* SDRAM Test range - start at 16 meg boundary -ends at 32Meg -
 283  * a basic sanity check ONLY
 284  * IF you would like to increase coverage, increase the end address
 285  * or run the test with custom options
 286  */
 287 #define CONFIG_SYS_MEMTEST_START        (OMAP34XX_SDRC_CS0 + 0x01000000)
 288 #define CONFIG_SYS_MEMTEST_END          (OMAP34XX_SDRC_CS0 + (32 << 20))
 289
 290 /* Default load address */
 291 #define CONFIG_SYS_LOAD_ADDR            (OMAP34XX_SDRC_CS0)
 292
 293 /*--------------------------------------------------------------------------*/
 294
 295 /*
 296  * 3430 has 12 GP timers, they can be driven by the SysClk (12/13/19.2) or by
 297  * 32KHz clk, or from external sig. This rate is divided by a local divisor.
 298  */
 299 #define CONFIG_SYS_TIMERBASE            (OMAP34XX_GPT2)
 300 #define CONFIG_SYS_PTV                  2       /* Divisor: 2^(PTV+1) => 8 */
 301 #define CONFIG_SYS_HZ                   1000
 302
 303 /*
 304  * Stack sizes
 305  *
 306  * The stack sizes are set up in start.S using the settings below
 307  */
 308 #define CONFIG_STACKSIZE        (128 << 10) /* Regular stack */
 309 #ifdef CONFIG_USE_IRQ
 310 #define CONFIG_STACKSIZE_IRQ    (4 << 10) /* IRQ stack */
 311 #define CONFIG_STACKSIZE_FIQ    (4 << 10) /* FIQ stack */
 312 #endif
 313
 314 #define CONFIG_SYS_SDRAM_BASE           PHYS_SDRAM_1
 315 #define CONFIG_SYS_INIT_RAM_ADDR        0x4020f800
 316 #define CONFIG_SYS_INIT_RAM_SIZE        0x800
 317 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_INIT_RAM_ADDR + \
 318                                          CONFIG_SYS_INIT_RAM_SIZE - \
 319                                          GENERATED_GBL_DATA_SIZE)
 320 /*
 321  * SDRAM Memory Map
 322  */
 323 #define CONFIG_NR_DRAM_BANKS    2       /* CS1 may or may not be populated */
 324 #define PHYS_SDRAM_1            OMAP34XX_SDRC_CS0
 325 #define PHYS_SDRAM_1_SIZE       (32 << 20) /* at least 32 meg */
 326 #define PHYS_SDRAM_2            OMAP34XX_SDRC_CS1
 327
 328 /* SDRAM Bank Allocation method */
 329 #define SDRC_R_B_C              1
 330
 331 /*--------------------------------------------------------------------------*/
 332
 333 /*
 334  * NOR FLASH usage ... default nCS0:
 335  *  - one 256KB sector for U-Boot
 336  *  - one 256KB sector for its parameters (not all used)
 337  *  - eight sectors (2 MB) for kernel
 338  *  - rest for JFFS2
 339  */
 340
 341 /* Monitor at start of flash */
 342 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_FLASH_BASE
 343 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)
 344
 345 /*
 346  * NAND FLASH usage ... default nCS1:
 347  *  - four 128KB sectors for X-Loader
 348  *  - four 128KB sectors for U-Boot
 349  *  - two 128KB sector for its parameters
 350  *  - 32 sectors (4 MB) for kernel
 351  *  - rest for filesystem
 352  */
 353
 354 /*
 355  * OneNAND FLASH usage ... default nCS2:
 356  *  - four 128KB sectors for X-Loader
 357  *  - two 128KB sectors for U-Boot
 358  *  - one 128KB sector for its parameters
 359  *  - sixteen sectors (2 MB) for kernel
 360  *  - rest for filesystem
 361  */
 362
 363 #endif                          /* __CONFIG_H */