include/configs/rut.h

   1 /*
   2  * siemens rut
   3  * (C) Copyright 2013 Siemens Schweiz AG
   4  * (C) Heiko Schocher, DENX Software Engineering, hs@denx.de.
   5  *
   6  * Based on:
   7  * U-Boot file:/include/configs/am335x_evm.h
   8  *
   9  * Copyright (C) 2011 Texas Instruments Incorporated - http://www.ti.com/
  10  *
  11  * SPDX-License-Identifier:     GPL-2.0+
  12  */
  13
  14 #ifndef __CONFIG_RUT_H
  15 #define __CONFIG_RUT_H
  16
  17 #define CONFIG_SIEMENS_RUT
  18 #define MACH_TYPE_RUT                   4316
  19 #define CONFIG_SIEMENS_MACH_TYPE        MACH_TYPE_RUT
  20
  21 #include "siemens-am33x-common.h"
  22
  23 #define CONFIG_SYS_MPUCLK       600
  24 #define RUT_IOCTRL_VAL  0x18b
  25 #define DDR_PLL_FREQ    303
  26
  27  /* Physical Memory Map */
  28 #define CONFIG_MAX_RAM_BANK_SIZE        (256 << 20) /* 256 MiB */
  29
  30 /* I2C Configuration */
  31 #define CONFIG_SYS_I2C_SPEED            100000
  32
  33 #define CONFIG_SYS_I2C_EEPROM_ADDR              0x50
  34 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN          2
  35 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS       6       /* 64 byte pages */
  36 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10      /* take up to 10 msec */
  37
  38 #define CONFIG_PHY_NATSEMI
  39
  40 #define CONFIG_FACTORYSET
  41
  42 /* Watchdog */
  43 #define WATCHDOG_TRIGGER_GPIO   14
  44
  45 #ifndef CONFIG_SPL_BUILD
  46
  47 /* Use common default */
  48 #define MTDPARTS_DEFAULT        MTDPARTS_DEFAULT_V1
  49
  50 /* Default env settings */
  51 #define CONFIG_EXTRA_ENV_SETTINGS \
  52         "hostname=rut\0" \
  53         "ubi_off=2048\0"\
  54         "nand_img_size=0x500000\0" \
  55         "splashpos=m,m\0" \
  56         "optargs=fixrtc --no-log consoleblank=0 \0" \
  57         CONFIG_ENV_SETTINGS_V1 \
  58         CONFIG_ENV_SETTINGS_NAND_V1 \
  59         "mmc_dev=0\0" \
  60         "mmc_root=/dev/mmcblk0p2 rw\0" \
  61         "mmc_root_fs_type=ext4 rootwait\0" \
  62         "mmc_load_uimage=" \
  63                 "mmc rescan; " \
  64                 "setenv bootfile uImage;" \
  65                 "fatload mmc ${mmc_dev} ${kloadaddr} ${bootfile}\0" \
  66         "loadbootenv=fatload mmc ${mmc_dev} ${loadaddr} ${bootenv}\0" \
  67         "importbootenv=echo Importing environment from mmc ...; " \
  68                 "env import -t $loadaddr $filesize\0" \
  69         "mmc_args=run bootargs_defaults;" \
  70                 "mtdparts default;" \
  71                 "setenv bootargs ${bootargs} " \
  72                 "root=${mmc_root} ${mtdparts}" \
  73                 "rootfstype=${mmc_root_fs_type} ip=${ip_method} " \
  74                 "eth=${ethaddr} " \
  75                 "\0" \
  76         "mmc_boot=run mmc_args; " \
  77                 "run mmc_load_uimage; " \
  78                 "bootm ${kloadaddr}\0" \
  79         ""
  80
  81 #ifndef CONFIG_RESTORE_FLASH
  82 /* set to negative value for no autoboot */
  83
  84 #define CONFIG_BOOTCOMMAND \
  85         "if mmc rescan; then " \
  86                 "echo SD/MMC found on device ${mmc_dev};" \
  87                 "if run loadbootenv; then " \
  88                         "echo Loaded environment from ${bootenv};" \
  89                         "run importbootenv;" \
  90                 "fi;" \
  91                 "if test -n $uenvcmd; then " \
  92                         "echo Running uenvcmd ...;" \
  93                         "run uenvcmd;" \
  94                 "fi;" \
  95                 "if run mmc_load_uimage; then " \
  96                         "run mmc_args;" \
  97                         "bootm ${kloadaddr};" \
  98                 "fi;" \
  99         "fi;" \
 100         "run nand_boot;" \
 101         "reset;"
 102
 103 #else
 104
 105 #define CONFIG_BOOTCOMMAND                      \
 106         "setenv autoload no; "                  \
 107         "dhcp; "                                \
 108         "if tftp 80000000 debrick.scr; then "   \
 109                 "source 80000000; "             \
 110         "fi"
 111 #endif
 112
 113 #endif /* CONFIG_SPL_BUILD */
 114
 115 #ifdef CONFIG_SPL_BUILD
 116 #undef CONFIG_HW_WATCHDOG
 117 #endif
 118
 119 #if defined(CONFIG_VIDEO)
 120 #define CONFIG_VIDEO_DA8XX
 121 #define CONFIG_SPLASH_SCREEN
 122 #define CONFIG_SPLASH_SCREEN_ALIGN
 123 #define CONFIG_VIDEO_LOGO
 124 #define CONFIG_VIDEO_BMP_RLE8
 125 #define CONFIG_VIDEO_BMP_LOGO
 126 #define CONFIG_CMD_BMP
 127 #define DA8XX_LCD_CNTL_BASE     LCD_CNTL_BASE
 128
 129 #define CONFIG_SPI
 130 #define CONFIG_OMAP3_SPI
 131
 132 #define BOARD_LCD_RESET         115     /* Bank 3 pin 19 */
 133 #define CONFIG_FORMIKE
 134 #define DISPL_PLL_SPREAD_SPECTRUM
 135 #endif
 136
 137 #endif  /* ! __CONFIG_RUT_H */