include/configs/woodburn_common.h

   1 /*
   2  * (C) Copyright 2011, Stefano Babic <sbabic@denx.de>
   3  *
   4  * (C) Copyright 2008-2010 Freescale Semiconductor, Inc.
   5  *
   6  * Configuration for the woodburn board.
   7  *
   8  * SPDX-License-Identifier:     GPL-2.0+
   9  */
  10
  11 #ifndef __WOODBURN_COMMON_CONFIG_H
  12 #define __WOODBURN_COMMON_CONFIG_H
  13
  14 #include <asm/arch/imx-regs.h>
  15
  16  /* High Level Configuration Options */
  17 #define CONFIG_MX35
  18 #define CONFIG_MX35_HCLK_FREQ   24000000
  19 #define CONFIG_SYS_FSL_CLK
  20
  21 #define CONFIG_SYS_DCACHE_OFF
  22
  23 #define CONFIG_DISPLAY_CPUINFO
  24
  25 /* Only in case the value is not present in mach-types.h */
  26 #ifndef MACH_TYPE_FLEA3
  27 #define MACH_TYPE_FLEA3                3668
  28 #endif
  29
  30 #define CONFIG_MACH_TYPE                MACH_TYPE_FLEA3
  31
  32 /* This is required to setup the ESDC controller */
  33
  34 #define CONFIG_CMDLINE_TAG              /* enable passing of ATAGs */
  35 #define CONFIG_REVISION_TAG
  36 #define CONFIG_SETUP_MEMORY_TAGS
  37 #define CONFIG_INITRD_TAG
  38
  39 /*
  40  * Size of malloc() pool
  41  */
  42 #define CONFIG_SYS_MALLOC_LEN           (CONFIG_ENV_SIZE + 1024 * 1024)
  43
  44 /*
  45  * Hardware drivers
  46  */
  47 #define CONFIG_SYS_I2C
  48 #define CONFIG_SYS_I2C_MXC
  49 #define CONFIG_SYS_I2C_MXC_I2C1         /* enable I2C bus 1 */
  50 #define CONFIG_SYS_I2C_MXC_I2C2         /* enable I2C bus 2 */
  51 #define CONFIG_SYS_I2C_MXC_I2C3         /* enable I2C bus 3 */
  52 #define CONFIG_SYS_SPD_BUS_NUM          0
  53 #define CONFIG_MXC_SPI
  54 #define CONFIG_MXC_GPIO
  55
  56 /* PMIC Controller */
  57 #define CONFIG_POWER
  58 #define CONFIG_POWER_I2C
  59 #define CONFIG_POWER_FSL
  60 #define CONFIG_POWER_FSL_MC13892
  61 #define CONFIG_SYS_FSL_PMIC_I2C_ADDR    0x8
  62 #define CONFIG_RTC_MC13XXX
  63
  64 /* mmc driver */
  65 #define CONFIG_MMC
  66 #define CONFIG_GENERIC_MMC
  67 #define CONFIG_FSL_ESDHC
  68 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
  69 #define CONFIG_SYS_FSL_ESDHC_NUM        1
  70
  71 /*
  72  * UART (console)
  73  */
  74 #define CONFIG_MXC_UART
  75 #define CONFIG_MXC_UART_BASE    UART1_BASE
  76
  77 /* allow to overwrite serial and ethaddr */
  78 #define CONFIG_ENV_OVERWRITE
  79 #define CONFIG_CONS_INDEX       1
  80 #define CONFIG_BAUDRATE         115200
  81
  82 /*
  83  * Command definition
  84  */
  85 #define CONFIG_CMD_DATE
  86 #define CONFIG_BOOTP_SUBNETMASK
  87 #define CONFIG_BOOTP_GATEWAY
  88 #define CONFIG_BOOTP_DNS
  89
  90 #define CONFIG_CMD_NAND
  91
  92 #define CONFIG_DOS_PARTITION
  93 #define CONFIG_EFI_PARTITION
  94
  95 #define CONFIG_MXC_GPIO
  96
  97 #define CONFIG_NET_RETRY_COUNT  100
  98
  99
 100 #define CONFIG_LOADADDR         0x80800000      /* loadaddr env var */
 101
 102 /*
 103  * Ethernet on SOC (FEC)
 104  */
 105 #define CONFIG_FEC_MXC
 106 #define IMX_FEC_BASE    FEC_BASE_ADDR
 107 #define CONFIG_PHYLIB
 108 #define CONFIG_PHY_MICREL
 109 #define CONFIG_FEC_MXC_PHYADDR  0x1
 110
 111 #define CONFIG_MII
 112 #define CONFIG_DISCOVER_PHY
 113
 114 #define CONFIG_ARP_TIMEOUT      200UL
 115
 116 /*
 117  * Miscellaneous configurable options
 118  */
 119 #define CONFIG_SYS_LONGHELP     /* undef to save memory */
 120 #define CONFIG_CMDLINE_EDITING
 121
 122 #define CONFIG_AUTO_COMPLETE
 123 #define CONFIG_SYS_CBSIZE       256     /* Console I/O Buffer Size */
 124 /* Print Buffer Size */
 125 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
 126 #define CONFIG_SYS_MAXARGS      16      /* max number of command args */
 127 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
 128
 129 #define CONFIG_SYS_MEMTEST_START        0       /* memtest works on */
 130 #define CONFIG_SYS_MEMTEST_END          0x10000
 131
 132 #define CONFIG_SYS_LOAD_ADDR            CONFIG_LOADADDR
 133
 134 /*
 135  * Stack sizes
 136  *
 137  * The stack sizes are set up in start.S using the settings below
 138  */
 139 #define CONFIG_STACKSIZE        (128 * 1024)    /* regular stack */
 140
 141 /*
 142  * Physical Memory Map
 143  */
 144 #define CONFIG_NR_DRAM_BANKS    1
 145 #define PHYS_SDRAM_1            CSD0_BASE_ADDR
 146 #define PHYS_SDRAM_1_SIZE       (256 * 1024 * 1024)
 147
 148 #define CONFIG_SYS_SDRAM_BASE           CSD0_BASE_ADDR
 149
 150 #define CONFIG_SYS_GBL_DATA_OFFSET      (LOW_LEVEL_SRAM_STACK - \
 151                                                 IRAM_BASE_ADDR - \
 152                                                 GENERATED_GBL_DATA_SIZE)
 153 #define CONFIG_SYS_INIT_SP_ADDR         (IRAM_BASE_ADDR + \
 154                                         CONFIG_SYS_GBL_DATA_OFFSET)
 155
 156 /*
 157  * MTD Command for mtdparts
 158  */
 159 #define CONFIG_CMD_MTDPARTS
 160 #define CONFIG_MTD_DEVICE
 161 #define CONFIG_FLASH_CFI_MTD
 162 #define CONFIG_MTD_PARTITIONS
 163 #define MTDIDS_DEFAULT          "nand0=mxc_nand,nor0=physmap-flash.0"
 164 #define MTDPARTS_DEFAULT        "mtdparts=mxc_nand:50m(root1)," \
 165                                 "32m(rootfb)," \
 166                                 "64m(pcache)," \
 167                                 "64m(app1)," \
 168                                 "10m(app2),-(spool);" \
 169                                 "physmap-flash.0:512k(u-boot),64k(env1)," \
 170                                 "64k(env2),3776k(kernel1),3776k(kernel2)"
 171
 172 /*
 173  * FLASH and environment organization
 174  */
 175 #define CONFIG_SYS_FLASH_BASE           CS0_BASE_ADDR
 176 #define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
 177 #define CONFIG_SYS_MAX_FLASH_SECT 512   /* max number of sectors on one chip */
 178 /* Monitor at beginning of flash */
 179 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
 180 #define CONFIG_SYS_MONITOR_LEN          (512 * 1024)
 181
 182 #define CONFIG_ENV_SECT_SIZE    (128 * 1024)
 183 #define CONFIG_ENV_SIZE         CONFIG_ENV_SECT_SIZE
 184
 185 /* Address and size of Redundant Environment Sector     */
 186 #define CONFIG_ENV_OFFSET_REDUND        (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
 187 #define CONFIG_ENV_SIZE_REDUND  CONFIG_ENV_SIZE
 188
 189 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + \
 190                                 CONFIG_SYS_MONITOR_LEN)
 191
 192 #define CONFIG_ENV_IS_IN_FLASH
 193
 194 /*
 195  * CFI FLASH driver setup
 196  */
 197 #define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
 198 #define CONFIG_FLASH_CFI_DRIVER
 199
 200 /* A non-standard buffered write algorithm */
 201 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE       /* faster */
 202 #define CONFIG_SYS_FLASH_PROTECTION     /* Use hardware sector protection */
 203
 204 /*
 205  * NAND FLASH driver setup
 206  */
 207 #define CONFIG_NAND_MXC
 208 #define CONFIG_NAND_MXC_V1_1
 209 #define CONFIG_MXC_NAND_REGS_BASE       (NFC_BASE_ADDR)
 210 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 211 #define CONFIG_SYS_NAND_BASE            (NFC_BASE_ADDR)
 212 #define CONFIG_MXC_NAND_HWECC
 213 #define CONFIG_SYS_NAND_LARGEPAGE
 214
 215 #if 0
 216 #define CONFIG_MTD_DEBUG
 217 #define CONFIG_MTD_DEBUG_VERBOSE        7
 218 #endif
 219 #define CONFIG_SYS_NAND_ONFI_DETECTION
 220
 221 /*
 222  * Default environment and default scripts
 223  * to update uboot and load kernel
 224  */
 225
 226 #define CONFIG_HOSTNAME woodburn
 227 #define CONFIG_EXTRA_ENV_SETTINGS                                       \
 228         "netdev=eth0\0"                                                 \
 229         "nfsargs=setenv bootargs root=/dev/nfs rw "                     \
 230                 "nfsroot=${serverip}:${rootpath}\0"                     \
 231         "ramargs=setenv bootargs root=/dev/ram rw\0"                    \
 232         "addip_sta=setenv bootargs ${bootargs} "                        \
 233                 "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"      \
 234                 ":${hostname}:${netdev}:off panic=1\0"                  \
 235         "addip_dyn=setenv bootargs ${bootargs} ip=dhcp\0"               \
 236         "addip=if test -n ${ipdyn};then run addip_dyn;"                 \
 237                 "else run addip_sta;fi\0"       \
 238         "addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"              \
 239         "addtty=setenv bootargs ${bootargs}"                            \
 240                 " console=ttymxc0,${baudrate}\0"                        \
 241         "addmisc=setenv bootargs ${bootargs} ${misc}\0"                 \
 242         "loadaddr=80800000\0"                                           \
 243         "kernel_addr_r=80800000\0"                                      \
 244         "hostname=" __stringify(CONFIG_HOSTNAME) "\0"                   \
 245         "bootfile=" __stringify(CONFIG_HOSTNAME) "/uImage\0"            \
 246         "ramdisk_file=" __stringify(CONFIG_HOSTNAME) "/uRamdisk\0"      \
 247         "flash_self=run ramargs addip addtty addmtd addmisc;"           \
 248                 "bootm ${kernel_addr} ${ramdisk_addr}\0"                \
 249         "flash_nfs=run nfsargs addip addtty addmtd addmisc;"            \
 250                 "bootm ${kernel_addr}\0"                                \
 251         "net_nfs=tftp ${kernel_addr_r} ${bootfile}; "                   \
 252                 "run nfsargs addip addtty addmtd addmisc;"              \
 253                 "bootm ${kernel_addr_r}\0"                              \
 254         "net_self_load=tftp ${kernel_addr_r} ${bootfile};"              \
 255                 "tftp ${ramdisk_addr_r} ${ramdisk_file};\0"             \
 256         "net_self=if run net_self_load;then "                           \
 257                 "run ramargs addip addtty addmtd addmisc;"              \
 258                 "bootm ${kernel_addr_r} ${ramdisk_addr_r};"             \
 259                 "else echo Images not loades;fi\0"                      \
 260         "u-boot=" __stringify(CONFIG_HOSTNAME) "/u-boot.bin\0"          \
 261         "load=tftp ${loadaddr} ${u-boot}\0"                             \
 262         "uboot_addr=" __stringify(CONFIG_SYS_MONITOR_BASE) "\0"         \
 263         "update=protect off ${uboot_addr} +80000;"                      \
 264                 "erase ${uboot_addr} +80000;"                           \
 265                 "cp.b ${loadaddr} ${uboot_addr} ${filesize}\0"          \
 266         "upd=if run load;then echo Updating u-boot;if run update;"      \
 267                 "then echo U-Boot updated;"                             \
 268                         "else echo Error updating u-boot !;"            \
 269                         "echo Board without bootloader !!;"             \
 270                 "fi;"                                                   \
 271                 "else echo U-Boot not downloaded..exiting;fi\0"         \
 272         "bootcmd=run net_nfs\0"
 273
 274 #endif                          /* __CONFIG_H */