include/configs/zynq-common.h

   1 /*
   2  * (C) Copyright 2012 Michal Simek <monstr@monstr.eu>
   3  * (C) Copyright 2013 Xilinx, Inc.
   4  *
   5  * Common configuration options for all Zynq boards.
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 #ifndef __CONFIG_ZYNQ_COMMON_H
  11 #define __CONFIG_ZYNQ_COMMON_H
  12
  13 /* CPU clock */
  14 #ifndef CONFIG_CPU_FREQ_HZ
  15 # define CONFIG_CPU_FREQ_HZ     800000000
  16 #endif
  17
  18 /* Cache options */
  19 #define CONFIG_CMD_CACHE
  20 #define CONFIG_SYS_CACHELINE_SIZE       32
  21
  22 #define CONFIG_SYS_L2CACHE_OFF
  23 #ifndef CONFIG_SYS_L2CACHE_OFF
  24 # define CONFIG_SYS_L2_PL310
  25 # define CONFIG_SYS_PL310_BASE          0xf8f02000
  26 #endif
  27
  28 #define ZYNQ_SCUTIMER_BASEADDR          0xF8F00600
  29 #define CONFIG_SYS_TIMERBASE            ZYNQ_SCUTIMER_BASEADDR
  30 #define CONFIG_SYS_TIMER_COUNTS_DOWN
  31 #define CONFIG_SYS_TIMER_COUNTER        (CONFIG_SYS_TIMERBASE + 0x4)
  32
  33 /* Serial drivers */
  34 #define CONFIG_BAUDRATE         115200
  35 /* The following table includes the supported baudrates */
  36 #define CONFIG_SYS_BAUDRATE_TABLE  \
  37         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
  38
  39 #define CONFIG_ARM_DCC
  40 #define CONFIG_ZYNQ_SERIAL
  41
  42 /* Ethernet driver */
  43 #if defined(CONFIG_ZYNQ_GEM)
  44 # define CONFIG_MII
  45 # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  46 # define CONFIG_PHY_MARVELL
  47 # define CONFIG_PHY_REALTEK
  48 # define CONFIG_PHY_XILINX
  49 # define CONFIG_BOOTP_SERVERIP
  50 # define CONFIG_BOOTP_BOOTPATH
  51 # define CONFIG_BOOTP_GATEWAY
  52 # define CONFIG_BOOTP_HOSTNAME
  53 # define CONFIG_BOOTP_MAY_FAIL
  54 #endif
  55
  56 /* SPI */
  57 #ifdef CONFIG_ZYNQ_SPI
  58 # define CONFIG_CMD_SF
  59 #endif
  60
  61 /* QSPI */
  62 #ifdef CONFIG_ZYNQ_QSPI
  63 # define CONFIG_SF_DEFAULT_SPEED        30000000
  64 # define CONFIG_SPI_FLASH_ISSI
  65 # define CONFIG_CMD_SF
  66 #endif
  67
  68 /* NOR */
  69 #ifndef CONFIG_SYS_NO_FLASH
  70 # define CONFIG_SYS_FLASH_BASE          0xE2000000
  71 # define CONFIG_SYS_FLASH_SIZE          (16 * 1024 * 1024)
  72 # define CONFIG_SYS_MAX_FLASH_BANKS     1
  73 # define CONFIG_SYS_MAX_FLASH_SECT      512
  74 # define CONFIG_SYS_FLASH_ERASE_TOUT    1000
  75 # define CONFIG_SYS_FLASH_WRITE_TOUT    5000
  76 # define CONFIG_FLASH_SHOW_PROGRESS     10
  77 # define CONFIG_SYS_FLASH_CFI
  78 # undef CONFIG_SYS_FLASH_EMPTY_INFO
  79 # define CONFIG_FLASH_CFI_DRIVER
  80 # undef CONFIG_SYS_FLASH_PROTECTION
  81 # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
  82 #endif
  83
  84 /* MMC */
  85 #if defined(CONFIG_ZYNQ_SDHCI)
  86 # define CONFIG_MMC
  87 # define CONFIG_GENERIC_MMC
  88 # define CONFIG_SDHCI
  89 # define CONFIG_CMD_MMC
  90 # define CONFIG_ZYNQ_SDHCI_MAX_FREQ     52000000
  91 #endif
  92
  93 #ifdef CONFIG_ZYNQ_USB
  94 # define CONFIG_USB_EHCI
  95 # define CONFIG_CMD_USB
  96 # define CONFIG_USB_STORAGE
  97 # define CONFIG_USB_EHCI_ZYNQ
  98 # define CONFIG_EHCI_IS_TDI
  99 # define CONFIG_USB_MAX_CONTROLLER_COUNT        2
 100
 101 # define CONFIG_SYS_DFU_DATA_BUF_SIZE   0x600000
 102 # define DFU_DEFAULT_POLL_TIMEOUT       300
 103 # define CONFIG_USB_FUNCTION_DFU
 104 # define CONFIG_DFU_RAM
 105 # define CONFIG_USB_CABLE_CHECK
 106 # define CONFIG_CMD_DFU
 107 # define CONFIG_CMD_THOR_DOWNLOAD
 108 # define CONFIG_THOR_RESET_OFF
 109 # define CONFIG_USB_FUNCTION_THOR
 110 # define DFU_ALT_INFO_RAM \
 111         "dfu_ram_info=" \
 112         "set dfu_alt_info " \
 113         "${kernel_image} ram 0x3000000 0x500000\\\\;" \
 114         "${devicetree_image} ram 0x2A00000 0x20000\\\\;" \
 115         "${ramdisk_image} ram 0x2000000 0x600000\0" \
 116         "dfu_ram=run dfu_ram_info && dfu 0 ram 0\0" \
 117         "thor_ram=run dfu_ram_info && thordown 0 ram 0\0"
 118
 119 # if defined(CONFIG_ZYNQ_SDHCI)
 120 #  define CONFIG_DFU_MMC
 121 #  define DFU_ALT_INFO_MMC \
 122         "dfu_mmc_info=" \
 123         "set dfu_alt_info " \
 124         "${kernel_image} fat 0 1\\\\;" \
 125         "${devicetree_image} fat 0 1\\\\;" \
 126         "${ramdisk_image} fat 0 1\0" \
 127         "dfu_mmc=run dfu_mmc_info && dfu 0 mmc 0\0" \
 128         "thor_mmc=run dfu_mmc_info && thordown 0 mmc 0\0"
 129
 130 #  define DFU_ALT_INFO  \
 131         DFU_ALT_INFO_RAM \
 132         DFU_ALT_INFO_MMC
 133 # else
 134 #  define DFU_ALT_INFO  \
 135         DFU_ALT_INFO_RAM
 136 # endif
 137 #endif
 138
 139 #if !defined(DFU_ALT_INFO)
 140 # define DFU_ALT_INFO
 141 #endif
 142
 143 #if defined(CONFIG_ZYNQ_SDHCI) || defined(CONFIG_ZYNQ_USB)
 144 # define CONFIG_SUPPORT_VFAT
 145 # define CONFIG_CMD_FAT
 146 # define CONFIG_CMD_EXT2
 147 # define CONFIG_FAT_WRITE
 148 # define CONFIG_DOS_PARTITION
 149 # define CONFIG_CMD_EXT4
 150 # define CONFIG_CMD_EXT4_WRITE
 151 # define CONFIG_CMD_FS_GENERIC
 152 #endif
 153
 154 #if defined(CONFIG_ZYNQ_I2C0) || defined(CONFIG_ZYNQ_I2C1)
 155 #define CONFIG_SYS_I2C_ZYNQ
 156 #endif
 157
 158 /* I2C */
 159 #if defined(CONFIG_SYS_I2C_ZYNQ)
 160 # define CONFIG_CMD_I2C
 161 # define CONFIG_SYS_I2C
 162 # define CONFIG_SYS_I2C_ZYNQ_SPEED              100000
 163 # define CONFIG_SYS_I2C_ZYNQ_SLAVE              0
 164 #endif
 165
 166 /* EEPROM */
 167 #ifdef CONFIG_ZYNQ_EEPROM
 168 # define CONFIG_CMD_EEPROM
 169 # define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         1
 170 # define CONFIG_SYS_I2C_EEPROM_ADDR             0x54
 171 # define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      4
 172 # define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  5
 173 # define CONFIG_SYS_EEPROM_SIZE                 1024 /* Bytes */
 174 #endif
 175
 176 /* Total Size of Environment Sector */
 177 #define CONFIG_ENV_SIZE                 (128 << 10)
 178
 179 /* Allow to overwrite serial and ethaddr */
 180 #define CONFIG_ENV_OVERWRITE
 181
 182 /* Environment */
 183 #ifndef CONFIG_ENV_IS_NOWHERE
 184 # ifndef CONFIG_SYS_NO_FLASH
 185 /* Environment in NOR flash */
 186 #  define CONFIG_ENV_IS_IN_FLASH
 187 # elif defined(CONFIG_ZYNQ_QSPI)
 188 /* Environment in Serial Flash */
 189 #  define CONFIG_ENV_IS_IN_SPI_FLASH
 190 # elif defined(CONFIG_SYS_NO_FLASH)
 191 #  define CONFIG_ENV_IS_NOWHERE
 192 # endif
 193
 194 # define CONFIG_ENV_SECT_SIZE           CONFIG_ENV_SIZE
 195 # define CONFIG_ENV_OFFSET              0xE0000
 196 #endif
 197
 198 /* enable preboot to be loaded before CONFIG_BOOTDELAY */
 199 #define CONFIG_PREBOOT
 200
 201 /* Default environment */
 202 #ifndef CONFIG_EXTRA_ENV_SETTINGS
 203 #define CONFIG_EXTRA_ENV_SETTINGS       \
 204         "fit_image=fit.itb\0"           \
 205         "load_addr=0x2000000\0"         \
 206         "fit_size=0x800000\0"           \
 207         "flash_off=0x100000\0"          \
 208         "nor_flash_off=0xE2100000\0"    \
 209         "fdt_high=0x20000000\0"         \
 210         "initrd_high=0x20000000\0"      \
 211         "loadbootenv_addr=0x2000000\0" \
 212         "bootenv=uEnv.txt\0" \
 213         "bootenv_dev=mmc\0" \
 214         "loadbootenv=load ${bootenv_dev} 0 ${loadbootenv_addr} ${bootenv}\0" \
 215         "importbootenv=echo Importing environment from ${bootenv_dev} ...; " \
 216                 "env import -t ${loadbootenv_addr} $filesize\0" \
 217         "bootenv_existence_test=test -e ${bootenv_dev} 0 /${bootenv}\0" \
 218         "setbootenv=if env run bootenv_existence_test; then " \
 219                         "if env run loadbootenv; then " \
 220                                 "env run importbootenv; " \
 221                         "fi; " \
 222                 "fi; \0" \
 223         "sd_loadbootenv=set bootenv_dev mmc && " \
 224                         "run setbootenv \0" \
 225         "usb_loadbootenv=set bootenv_dev usb && usb start && run setbootenv \0" \
 226         "preboot=if test $modeboot = sdboot; then " \
 227                         "run sd_loadbootenv; " \
 228                         "echo Checking if uenvcmd is set ...; " \
 229                         "if test -n $uenvcmd; then " \
 230                                 "echo Running uenvcmd ...; " \
 231                                 "run uenvcmd; " \
 232                         "fi; " \
 233                 "fi; \0" \
 234         "norboot=echo Copying FIT from NOR flash to RAM... && " \
 235                 "cp.b ${nor_flash_off} ${load_addr} ${fit_size} && " \
 236                 "bootm ${load_addr}\0" \
 237         "sdboot=echo Copying FIT from SD to RAM... && " \
 238                 "load mmc 0 ${load_addr} ${fit_image} && " \
 239                 "bootm ${load_addr}\0" \
 240         "jtagboot=echo TFTPing FIT to RAM... && " \
 241                 "tftpboot ${load_addr} ${fit_image} && " \
 242                 "bootm ${load_addr}\0" \
 243         "usbboot=if usb start; then " \
 244                         "echo Copying FIT from USB to RAM... && " \
 245                         "load usb 0 ${load_addr} ${fit_image} && " \
 246                         "bootm ${load_addr}; fi\0" \
 247                 DFU_ALT_INFO
 248 #endif
 249
 250 #define CONFIG_BOOTCOMMAND              "run $modeboot"
 251 #define CONFIG_BOOTDELAY                3 /* -1 to Disable autoboot */
 252 #define CONFIG_SYS_LOAD_ADDR            0 /* default? */
 253
 254 /* Miscellaneous configurable options */
 255
 256 #define CONFIG_CMDLINE_EDITING
 257 #define CONFIG_AUTO_COMPLETE
 258 #define CONFIG_BOARD_LATE_INIT
 259 #define CONFIG_DISPLAY_BOARDINFO
 260 #define CONFIG_SYS_LONGHELP
 261 #define CONFIG_CLOCKS
 262 #define CONFIG_CMD_CLK
 263 #define CONFIG_SYS_MAXARGS              32 /* max number of command args */
 264 #define CONFIG_SYS_CBSIZE               256 /* Console I/O Buffer Size */
 265 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE + \
 266                                         sizeof(CONFIG_SYS_PROMPT) + 16)
 267
 268 /* Physical Memory map */
 269 #define CONFIG_SYS_TEXT_BASE            0x4000000
 270
 271 #ifndef CONFIG_NR_DRAM_BANKS
 272 # define CONFIG_NR_DRAM_BANKS           1
 273 #endif
 274
 275 #define CONFIG_SYS_MEMTEST_START        0
 276 #define CONFIG_SYS_MEMTEST_END          0x1000
 277
 278 #define CONFIG_SYS_MALLOC_LEN           0x1400000
 279
 280 #define CONFIG_SYS_INIT_RAM_ADDR        0xFFFF0000
 281 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000
 282 #define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_INIT_RAM_ADDR + \
 283                                         CONFIG_SYS_INIT_RAM_SIZE - \
 284                                         GENERATED_GBL_DATA_SIZE)
 285
 286 /* Enable the PL to be downloaded */
 287 #define CONFIG_FPGA
 288 #define CONFIG_FPGA_XILINX
 289 #define CONFIG_FPGA_ZYNQPL
 290 #define CONFIG_CMD_FPGA_LOADMK
 291 #define CONFIG_CMD_FPGA_LOADP
 292 #define CONFIG_CMD_FPGA_LOADBP
 293 #define CONFIG_CMD_FPGA_LOADFS
 294
 295 /* FIT support */
 296 #define CONFIG_IMAGE_FORMAT_LEGACY /* enable also legacy image format */
 297
 298 /* FDT support */
 299 #define CONFIG_DISPLAY_BOARDINFO_LATE
 300
 301 /* Extend size of kernel image for uncompression */
 302 #define CONFIG_SYS_BOOTM_LEN    (60 * 1024 * 1024)
 303
 304 /* Boot FreeBSD/vxWorks from an ELF image */
 305 #define CONFIG_SYS_MMC_MAX_DEVICE       1
 306
 307 #define CONFIG_SYS_LDSCRIPT  "arch/arm/mach-zynq/u-boot.lds"
 308
 309 /* Commands */
 310 #define CONFIG_CMD_PING
 311 #define CONFIG_CMD_DHCP
 312 #define CONFIG_CMD_MII
 313 #define CONFIG_CMD_TFTPPUT
 314
 315 /* SPL part */
 316 #define CONFIG_CMD_SPL
 317 #define CONFIG_SPL_FRAMEWORK
 318 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 319 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 320 #define CONFIG_SPL_SERIAL_SUPPORT
 321 #define CONFIG_SPL_BOARD_INIT
 322 #define CONFIG_SPL_RAM_DEVICE
 323
 324 #define CONFIG_SPL_LDSCRIPT     "arch/arm/mach-zynq/u-boot-spl.lds"
 325
 326 /* MMC support */
 327 #ifdef CONFIG_ZYNQ_SDHCI
 328 #define CONFIG_SPL_MMC_SUPPORT
 329 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
 330 #define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS      0x200 /* 256 KB */
 331 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION     1
 332 #define CONFIG_SPL_LIBDISK_SUPPORT
 333 #define CONFIG_SPL_FAT_SUPPORT
 334 #ifdef CONFIG_OF_SEPARATE
 335 # define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME     "u-boot-dtb.img"
 336 #else
 337 # define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME     "u-boot.img"
 338 #endif
 339 #endif
 340
 341 /* Disable dcache for SPL just for sure */
 342 #ifdef CONFIG_SPL_BUILD
 343 #define CONFIG_SYS_DCACHE_OFF
 344 #undef CONFIG_FPGA
 345 #endif
 346
 347 /* Address in RAM where the parameters must be copied by SPL. */
 348 #define CONFIG_SYS_SPL_ARGS_ADDR        0x10000000
 349
 350 #define CONFIG_SPL_FS_LOAD_ARGS_NAME            "system.dtb"
 351 #define CONFIG_SPL_FS_LOAD_KERNEL_NAME          "uImage"
 352
 353 /* Not using MMC raw mode - just for compilation purpose */
 354 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR   0
 355 #define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS  0
 356 #define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0
 357
 358 /* qspi mode is working fine */
 359 #ifdef CONFIG_ZYNQ_QSPI
 360 #define CONFIG_SPL_SPI_SUPPORT
 361 #define CONFIG_SPL_SPI_LOAD
 362 #define CONFIG_SPL_SPI_FLASH_SUPPORT
 363 #define CONFIG_SYS_SPI_U_BOOT_OFFS      0x100000
 364 #define CONFIG_SYS_SPI_ARGS_OFFS        0x200000
 365 #define CONFIG_SYS_SPI_ARGS_SIZE        0x80000
 366 #define CONFIG_SYS_SPI_KERNEL_OFFS      (CONFIG_SYS_SPI_ARGS_OFFS + \
 367                                         CONFIG_SYS_SPI_ARGS_SIZE)
 368 #endif
 369
 370 /* for booting directly linux */
 371 #define CONFIG_SPL_OS_BOOT
 372
 373 /* SP location before relocation, must use scratch RAM */
 374 #define CONFIG_SPL_TEXT_BASE    0x0
 375
 376 /* 3 * 64kB blocks of OCM - one is on the top because of bootrom */
 377 #define CONFIG_SPL_MAX_SIZE     0x30000
 378
 379 /* The highest 64k OCM address */
 380 #define OCM_HIGH_ADDR   0xffff0000
 381
 382 /* On the top of OCM space */
 383 #define CONFIG_SYS_SPL_MALLOC_START     OCM_HIGH_ADDR
 384 #define CONFIG_SYS_SPL_MALLOC_SIZE      0x2000
 385
 386 /*
 387  * SPL stack position - and stack goes down
 388  * 0xfffffe00 is used for putting wfi loop.
 389  * Set it up as limit for now.
 390  */
 391 #define CONFIG_SPL_STACK        0xfffffe00
 392
 393 /* BSS setup */
 394 #define CONFIG_SPL_BSS_START_ADDR       0x100000
 395 #define CONFIG_SPL_BSS_MAX_SIZE         0x100000
 396
 397 #define CONFIG_SYS_UBOOT_START  CONFIG_SYS_TEXT_BASE
 398
 399
 400 #endif /* __CONFIG_ZYNQ_COMMON_H */