include/ns16550.h

   1 /*
   2  * NS16550 Serial Port
   3  * originally from linux source (arch/powerpc/boot/ns16550.h)
   4  *
   5  * Cleanup and unification
   6  * (C) 2009 by Detlev Zundel, DENX Software Engineering GmbH
   7  *
   8  * modified slightly to
   9  * have addresses as offsets from CONFIG_SYS_ISA_BASE
  10  * added a few more definitions
  11  * added prototypes for ns16550.c
  12  * reduced no of com ports to 2
  13  * modifications (c) Rob Taylor, Flying Pig Systems. 2000.
  14  *
  15  * added support for port on 64-bit bus
  16  * by Richard Danter (richard.danter@windriver.com), (C) 2005 Wind River Systems
  17  */
  18
  19 /*
  20  * Note that the following macro magic uses the fact that the compiler
  21  * will not allocate storage for arrays of size 0
  22  */
  23
  24 #include <linux/types.h>
  25
  26 #ifdef CONFIG_DM_SERIAL
  27 /*
  28  * For driver model we always use one byte per register, and sort out the
  29  * differences in the driver
  30  */
  31 #define CONFIG_SYS_NS16550_REG_SIZE (-1)
  32 #endif
  33
  34 #ifdef CONFIG_NS16550_DYNAMIC
  35 #define UART_REG(x)     unsigned char x
  36 #else
  37 #if !defined(CONFIG_SYS_NS16550_REG_SIZE) || (CONFIG_SYS_NS16550_REG_SIZE == 0)
  38 #error "Please define NS16550 registers size."
  39 #elif defined(CONFIG_SYS_NS16550_MEM32) && !defined(CONFIG_DM_SERIAL)
  40 #define UART_REG(x) u32 x
  41 #elif (CONFIG_SYS_NS16550_REG_SIZE > 0)
  42 #define UART_REG(x)                                                \
  43         unsigned char prepad_##x[CONFIG_SYS_NS16550_REG_SIZE - 1]; \
  44         unsigned char x;
  45 #elif (CONFIG_SYS_NS16550_REG_SIZE < 0)
  46 #define UART_REG(x)                                                     \
  47         unsigned char x;                                                \
  48         unsigned char postpad_##x[-CONFIG_SYS_NS16550_REG_SIZE - 1];
  49 #endif
  50 #endif /* CONFIG_NS16550_DYNAMIC */
  51
  52 enum ns16550_flags {
  53         NS16550_FLAG_IO         = 1 << 0, /* Use I/O access (else mem-mapped) */
  54         NS16550_FLAG_ENDIAN     = 1 << 1, /* Use out_le/be_32() */
  55         NS16550_FLAG_BE         = 1 << 2, /* Big-endian access (else little) */
  56 };
  57
  58 /**
  59  * struct ns16550_platdata - information about a NS16550 port
  60  *
  61  * @base:               Base register address
  62  * @reg_width:          IO accesses size of registers (in bytes, 1 or 4)
  63  * @reg_shift:          Shift size of registers (0=byte, 1=16bit, 2=32bit...)
  64  * @reg_offset:         Offset to start of registers (normally 0)
  65  * @clock:              UART base clock speed in Hz
  66  * @fcr:                Offset of FCR register (normally UART_FCR_DEFVAL)
  67  * @flags:              A few flags (enum ns16550_flags)
  68  * @bdf:                PCI slot/function (pci_dev_t)
  69  */
  70 struct ns16550_platdata {
  71         unsigned long base;
  72         int reg_width;
  73         int reg_shift;
  74         int reg_offset;
  75         int clock;
  76         u32 fcr;
  77         int flags;
  78 #if defined(CONFIG_PCI) && defined(CONFIG_SPL)
  79         int bdf;
  80 #endif
  81 };
  82
  83 struct udevice;
  84
  85 struct NS16550 {
  86         UART_REG(rbr);          /* 0 */
  87         UART_REG(ier);          /* 1 */
  88         UART_REG(fcr);          /* 2 */
  89         UART_REG(lcr);          /* 3 */
  90         UART_REG(mcr);          /* 4 */
  91         UART_REG(lsr);          /* 5 */
  92         UART_REG(msr);          /* 6 */
  93         UART_REG(spr);          /* 7 */
  94 #ifdef CONFIG_SOC_DA8XX
  95         UART_REG(reg8);         /* 8 */
  96         UART_REG(reg9);         /* 9 */
  97         UART_REG(revid1);       /* A */
  98         UART_REG(revid2);       /* B */
  99         UART_REG(pwr_mgmt);     /* C */
 100         UART_REG(mdr1);         /* D */
 101 #else
 102         UART_REG(mdr1);         /* 8 */
 103         UART_REG(reg9);         /* 9 */
 104         UART_REG(regA);         /* A */
 105         UART_REG(regB);         /* B */
 106         UART_REG(regC);         /* C */
 107         UART_REG(regD);         /* D */
 108         UART_REG(regE);         /* E */
 109         UART_REG(uasr);         /* F */
 110         UART_REG(scr);          /* 10*/
 111         UART_REG(ssr);          /* 11*/
 112 #endif
 113 #ifdef CONFIG_DM_SERIAL
 114         struct ns16550_platdata *plat;
 115 #endif
 116 };
 117
 118 #define thr rbr
 119 #define iir fcr
 120 #define dll rbr
 121 #define dlm ier
 122
 123 typedef struct NS16550 *NS16550_t;
 124
 125 /*
 126  * These are the definitions for the FIFO Control Register
 127  */
 128 #define UART_FCR_FIFO_EN        0x01 /* Fifo enable */
 129 #define UART_FCR_CLEAR_RCVR     0x02 /* Clear the RCVR FIFO */
 130 #define UART_FCR_CLEAR_XMIT     0x04 /* Clear the XMIT FIFO */
 131 #define UART_FCR_DMA_SELECT     0x08 /* For DMA applications */
 132 #define UART_FCR_TRIGGER_MASK   0xC0 /* Mask for the FIFO trigger range */
 133 #define UART_FCR_TRIGGER_1      0x00 /* Mask for trigger set at 1 */
 134 #define UART_FCR_TRIGGER_4      0x40 /* Mask for trigger set at 4 */
 135 #define UART_FCR_TRIGGER_8      0x80 /* Mask for trigger set at 8 */
 136 #define UART_FCR_TRIGGER_14     0xC0 /* Mask for trigger set at 14 */
 137
 138 #define UART_FCR_RXSR           0x02 /* Receiver soft reset */
 139 #define UART_FCR_TXSR           0x04 /* Transmitter soft reset */
 140
 141 /* Ingenic JZ47xx specific UART-enable bit. */
 142 #define UART_FCR_UME            0x10
 143
 144 /* Clear & enable FIFOs */
 145 #define UART_FCR_DEFVAL (UART_FCR_FIFO_EN | \
 146                         UART_FCR_RXSR | \
 147                         UART_FCR_TXSR)
 148
 149 /*
 150  * These are the definitions for the Modem Control Register
 151  */
 152 #define UART_MCR_DTR    0x01            /* DTR   */
 153 #define UART_MCR_RTS    0x02            /* RTS   */
 154 #define UART_MCR_OUT1   0x04            /* Out 1 */
 155 #define UART_MCR_OUT2   0x08            /* Out 2 */
 156 #define UART_MCR_LOOP   0x10            /* Enable loopback test mode */
 157 #define UART_MCR_AFE    0x20            /* Enable auto-RTS/CTS */
 158
 159 #define UART_MCR_DMA_EN 0x04
 160 #define UART_MCR_TX_DFR 0x08
 161
 162 /*
 163  * These are the definitions for the Line Control Register
 164  *
 165  * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
 166  * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
 167  */
 168 #define UART_LCR_WLS_MSK 0x03           /* character length select mask */
 169 #define UART_LCR_WLS_5  0x00            /* 5 bit character length */
 170 #define UART_LCR_WLS_6  0x01            /* 6 bit character length */
 171 #define UART_LCR_WLS_7  0x02            /* 7 bit character length */
 172 #define UART_LCR_WLS_8  0x03            /* 8 bit character length */
 173 #define UART_LCR_STB    0x04            /* # stop Bits, off=1, on=1.5 or 2) */
 174 #define UART_LCR_PEN    0x08            /* Parity eneble */
 175 #define UART_LCR_EPS    0x10            /* Even Parity Select */
 176 #define UART_LCR_STKP   0x20            /* Stick Parity */
 177 #define UART_LCR_SBRK   0x40            /* Set Break */
 178 #define UART_LCR_BKSE   0x80            /* Bank select enable */
 179 #define UART_LCR_DLAB   0x80            /* Divisor latch access bit */
 180
 181 /*
 182  * These are the definitions for the Line Status Register
 183  */
 184 #define UART_LSR_DR     0x01            /* Data ready */
 185 #define UART_LSR_OE     0x02            /* Overrun */
 186 #define UART_LSR_PE     0x04            /* Parity error */
 187 #define UART_LSR_FE     0x08            /* Framing error */
 188 #define UART_LSR_BI     0x10            /* Break */
 189 #define UART_LSR_THRE   0x20            /* Xmit holding register empty */
 190 #define UART_LSR_TEMT   0x40            /* Xmitter empty */
 191 #define UART_LSR_ERR    0x80            /* Error */
 192
 193 #define UART_MSR_DCD    0x80            /* Data Carrier Detect */
 194 #define UART_MSR_RI     0x40            /* Ring Indicator */
 195 #define UART_MSR_DSR    0x20            /* Data Set Ready */
 196 #define UART_MSR_CTS    0x10            /* Clear to Send */
 197 #define UART_MSR_DDCD   0x08            /* Delta DCD */
 198 #define UART_MSR_TERI   0x04            /* Trailing edge ring indicator */
 199 #define UART_MSR_DDSR   0x02            /* Delta DSR */
 200 #define UART_MSR_DCTS   0x01            /* Delta CTS */
 201
 202 /*
 203  * These are the definitions for the Interrupt Identification Register
 204  */
 205 #define UART_IIR_NO_INT 0x01    /* No interrupts pending */
 206 #define UART_IIR_ID     0x06    /* Mask for the interrupt ID */
 207
 208 #define UART_IIR_MSI    0x00    /* Modem status interrupt */
 209 #define UART_IIR_THRI   0x02    /* Transmitter holding register empty */
 210 #define UART_IIR_RDI    0x04    /* Receiver data interrupt */
 211 #define UART_IIR_RLSI   0x06    /* Receiver line status interrupt */
 212
 213 /*
 214  * These are the definitions for the Interrupt Enable Register
 215  */
 216 #define UART_IER_MSI    0x08    /* Enable Modem status interrupt */
 217 #define UART_IER_RLSI   0x04    /* Enable receiver line status interrupt */
 218 #define UART_IER_THRI   0x02    /* Enable Transmitter holding register int. */
 219 #define UART_IER_RDI    0x01    /* Enable receiver data interrupt */
 220
 221 /* useful defaults for LCR */
 222 #define UART_LCR_8N1    0x03
 223
 224 void NS16550_init(NS16550_t com_port, int baud_divisor);
 225 void NS16550_putc(NS16550_t com_port, char c);
 226 char NS16550_getc(NS16550_t com_port);
 227 int NS16550_tstc(NS16550_t com_port);
 228 void NS16550_reinit(NS16550_t com_port, int baud_divisor);
 229
 230 /**
 231  * ns16550_calc_divisor() - calculate the divisor given clock and baud rate
 232  *
 233  * Given the UART input clock and required baudrate, calculate the divisor
 234  * that should be used.
 235  *
 236  * @port:       UART port
 237  * @clock:      UART input clock speed in Hz
 238  * @baudrate:   Required baud rate
 239  * @return baud rate divisor that should be used
 240  */
 241 int ns16550_calc_divisor(NS16550_t port, int clock, int baudrate);
 242
 243 /**
 244  * ns16550_serial_ofdata_to_platdata() - convert DT to platform data
 245  *
 246  * Decode a device tree node for an ns16550 device. This includes the
 247  * register base address and register shift properties. The caller must set
 248  * up the clock frequency.
 249  *
 250  * @dev:        dev to decode platform data for
 251  * @return:     0 if OK, -EINVAL on error
 252  */
 253 int ns16550_serial_ofdata_to_platdata(struct udevice *dev);
 254
 255 /**
 256  * ns16550_serial_probe() - probe a serial port
 257  *
 258  * This sets up the serial port ready for use, except for the baud rate
 259  * @return 0, or -ve on error
 260  */
 261 int ns16550_serial_probe(struct udevice *dev);
 262
 263 /**
 264  * struct ns16550_serial_ops - ns16550 serial operations
 265  *
 266  * These should be used by the client driver for the driver's 'ops' member
 267  */
 268 extern const struct dm_serial_ops ns16550_serial_ops;