include/status_led.h

   1 /*
   2  * (C) Copyright 2000-2004
   3  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 /*
   9  * The purpose of this code is to signal the operational status of a
  10  * target which usually boots over the network; while running in
  11  * PCBoot, a status LED is blinking. As soon as a valid BOOTP reply
  12  * message has been received, the LED is turned off. The Linux
  13  * kernel, once it is running, will start blinking the LED again,
  14  * with another frequency.
  15  */
  16
  17 #ifndef _STATUS_LED_H_
  18 #define _STATUS_LED_H_
  19
  20 #ifdef CONFIG_STATUS_LED
  21
  22 #define STATUS_LED_OFF          0
  23 #define STATUS_LED_BLINKING     1
  24 #define STATUS_LED_ON           2
  25
  26 void status_led_tick (unsigned long timestamp);
  27 void status_led_set  (int led, int state);
  28
  29 /*****  TQM8xxL  ********************************************************/
  30 #if defined(CONFIG_TQM8xxL)
  31 # define STATUS_LED_PAR         im_cpm.cp_pbpar
  32 # define STATUS_LED_DIR         im_cpm.cp_pbdir
  33 # define STATUS_LED_ODR         im_cpm.cp_pbodr
  34 # define STATUS_LED_DAT         im_cpm.cp_pbdat
  35
  36 # define STATUS_LED_BIT         0x00000001
  37 # define STATUS_LED_PERIOD      (CONFIG_SYS_HZ / 2)
  38 # define STATUS_LED_STATE       STATUS_LED_BLINKING
  39
  40 # define STATUS_LED_ACTIVE      1               /* LED on for bit == 1  */
  41
  42 # define STATUS_LED_BOOT        0               /* LED 0 used for boot status */
  43
  44 /*****  MVS v1  **********************************************************/
  45 #elif (defined(CONFIG_MVS) && CONFIG_MVS < 2)
  46 # define STATUS_LED_PAR         im_ioport.iop_pdpar
  47 # define STATUS_LED_DIR         im_ioport.iop_pddir
  48 # undef  STATUS_LED_ODR
  49 # define STATUS_LED_DAT         im_ioport.iop_pddat
  50
  51 # define STATUS_LED_BIT         0x00000001
  52 # define STATUS_LED_PERIOD      (CONFIG_SYS_HZ / 2)
  53 # define STATUS_LED_STATE       STATUS_LED_BLINKING
  54
  55 # define STATUS_LED_ACTIVE      1               /* LED on for bit == 1  */
  56
  57 # define STATUS_LED_BOOT        0               /* LED 0 used for boot status */
  58
  59 /*****  IVMS8  **********************************************************/
  60 #elif defined(CONFIG_IVMS8)
  61
  62 # define STATUS_LED_PAR         im_cpm.cp_pbpar
  63 # define STATUS_LED_DIR         im_cpm.cp_pbdir
  64 # define STATUS_LED_ODR         im_cpm.cp_pbodr
  65 # define STATUS_LED_DAT         im_cpm.cp_pbdat
  66
  67 # define STATUS_LED_BIT         0x00000010      /* LED 0 is on PB.27    */
  68 # define STATUS_LED_PERIOD      (1 * CONFIG_SYS_HZ)
  69 # define STATUS_LED_STATE       STATUS_LED_OFF
  70 # define STATUS_LED_BIT1        0x00000020      /* LED 1 is on PB.26    */
  71 # define STATUS_LED_PERIOD1     (1 * CONFIG_SYS_HZ)
  72 # define STATUS_LED_STATE1      STATUS_LED_OFF
  73 /* IDE LED usable for other purposes, too */
  74 # define STATUS_LED_BIT2        0x00000008      /* LED 2 is on PB.28    */
  75 # define STATUS_LED_PERIOD2     (1 * CONFIG_SYS_HZ)
  76 # define STATUS_LED_STATE2      STATUS_LED_OFF
  77
  78 # define STATUS_LED_ACTIVE      1               /* LED on for bit == 1  */
  79
  80 # define STATUS_ILOCK_SWITCH    0x00800000      /* ILOCK switch in IRQ4 */
  81
  82 # define STATUS_ILOCK_PERIOD    (CONFIG_SYS_HZ / 10)    /* about every 100 ms   */
  83
  84 # define STATUS_LED_YELLOW      0
  85 # define STATUS_LED_GREEN       1
  86 # define STATUS_LED_BOOT        2               /* IDE LED used for boot status */
  87
  88 /*****  IVML24  *********************************************************/
  89 #elif defined(CONFIG_IVML24)
  90
  91 # define STATUS_LED_PAR         im_cpm.cp_pbpar
  92 # define STATUS_LED_DIR         im_cpm.cp_pbdir
  93 # define STATUS_LED_ODR         im_cpm.cp_pbodr
  94 # define STATUS_LED_DAT         im_cpm.cp_pbdat
  95
  96 # define STATUS_LED_BIT         0x00000010      /* LED 0 is on PB.27    */
  97 # define STATUS_LED_PERIOD      (1 * CONFIG_SYS_HZ)
  98 # define STATUS_LED_STATE       STATUS_LED_OFF
  99 # define STATUS_LED_BIT1        0x00000020      /* LED 1 is on PB.26    */
 100 # define STATUS_LED_PERIOD1     (1 * CONFIG_SYS_HZ)
 101 # define STATUS_LED_STATE1      STATUS_LED_OFF
 102 /* IDE LED usable for other purposes, too */
 103 # define STATUS_LED_BIT2        0x00000008      /* LED 2 is on PB.28    */
 104 # define STATUS_LED_PERIOD2     (1 * CONFIG_SYS_HZ)
 105 # define STATUS_LED_STATE2      STATUS_LED_OFF
 106
 107 # define STATUS_LED_ACTIVE      1               /* LED on for bit == 1  */
 108
 109 # define STATUS_ILOCK_SWITCH    0x00004000      /* ILOCK is on PB.17    */
 110
 111 # define STATUS_ILOCK_PERIOD    (CONFIG_SYS_HZ / 10)    /* about every 100 ms   */
 112
 113 # define STATUS_LED_YELLOW      0
 114 # define STATUS_LED_GREEN       1
 115 # define STATUS_LED_BOOT        2               /* IDE LED used for boot status */
 116
 117 /*****  Someone else defines these  *************************************/
 118 #elif defined(STATUS_LED_PAR)
 119
 120   /*
 121    * ADVICE: Define in your board configuration file rather than
 122    * filling this file up with lots of custom board stuff.
 123    */
 124
 125 /*****  NetVia   ********************************************************/
 126 #elif defined(CONFIG_NETVIA)
 127
 128 #if !defined(CONFIG_NETVIA_VERSION) || CONFIG_NETVIA_VERSION == 1
 129
 130 #define STATUS_LED_PAR          im_ioport.iop_pdpar
 131 #define STATUS_LED_DIR          im_ioport.iop_pddir
 132 #undef  STATUS_LED_ODR
 133 #define STATUS_LED_DAT          im_ioport.iop_pddat
 134
 135 # define STATUS_LED_BIT         0x0080                  /* PD.8 */
 136 # define STATUS_LED_PERIOD      (CONFIG_SYS_HZ / 2)
 137 # define STATUS_LED_STATE       STATUS_LED_BLINKING
 138
 139 # define STATUS_LED_BIT1        0x0040                  /* PD.9 */
 140 # define STATUS_LED_PERIOD1     (CONFIG_SYS_HZ / 2)
 141 # define STATUS_LED_STATE1      STATUS_LED_OFF
 142
 143 # define STATUS_LED_ACTIVE      0               /* LED on for bit == 0  */
 144 # define STATUS_LED_BOOT        0               /* LED 0 used for boot status */
 145
 146 #endif
 147
 148 /*****  CMI   ********************************************************/
 149 #elif defined(CONFIG_CMI)
 150 # define STATUS_LED_DIR         im_mios.mios_mpiosm32ddr
 151 # define STATUS_LED_DAT         im_mios.mios_mpiosm32dr
 152
 153 # define STATUS_LED_BIT         0x2000          /* Select one of the 16 possible*/
 154                                                 /* MIOS outputs */
 155 # define STATUS_LED_PERIOD      (CONFIG_SYS_HZ / 2)     /* Blinking periode is 500 ms */
 156 # define STATUS_LED_STATE       STATUS_LED_BLINKING
 157
 158 # define STATUS_LED_ACTIVE      1               /* LED on for bit == 0  */
 159 # define STATUS_LED_BOOT        0               /* LED 0 used for boot status */
 160
 161 /*****  KUP4K, KUP4X  ****************************************************/
 162 #elif defined(CONFIG_KUP4K) || defined(CONFIG_KUP4X)
 163
 164 # define STATUS_LED_PAR         im_ioport.iop_papar
 165 # define STATUS_LED_DIR         im_ioport.iop_padir
 166 # define STATUS_LED_ODR         im_ioport.iop_paodr
 167 # define STATUS_LED_DAT         im_ioport.iop_padat
 168
 169 # define STATUS_LED_BIT         0x00000300  /*  green + red    PA[8]=yellow,  PA[7]=red,  PA[6]=green */
 170 # define STATUS_LED_PERIOD      (CONFIG_SYS_HZ / 2)
 171 # define STATUS_LED_STATE       STATUS_LED_BLINKING
 172
 173 # define STATUS_LED_ACTIVE      1               /* LED on for bit == 1  */
 174
 175 # define STATUS_LED_BOOT        0               /* LED 0 used for boot status */
 176
 177 #elif defined(CONFIG_V38B)
 178
 179 # define STATUS_LED_BIT         0x0010                  /* Timer7 GPIO */
 180 # define STATUS_LED_PERIOD      (CONFIG_SYS_HZ / 2)
 181 # define STATUS_LED_STATE       STATUS_LED_BLINKING
 182
 183 # define STATUS_LED_ACTIVE      0               /* LED on for bit == 0 */
 184 # define STATUS_LED_BOOT        0               /* LED 0 used for boot status */
 185
 186 #elif defined(CONFIG_MOTIONPRO)
 187
 188 #define STATUS_LED_BIT          ((vu_long *) MPC5XXX_GPT6_ENABLE)
 189 #define STATUS_LED_PERIOD       (CONFIG_SYS_HZ / 10)
 190 #define STATUS_LED_STATE        STATUS_LED_BLINKING
 191
 192 #define STATUS_LED_BIT1         ((vu_long *) MPC5XXX_GPT7_ENABLE)
 193 #define STATUS_LED_PERIOD1      (CONFIG_SYS_HZ / 10)
 194 #define STATUS_LED_STATE1       STATUS_LED_OFF
 195
 196 #define STATUS_LED_BOOT         0       /* LED 0 used for boot status */
 197
 198 #elif defined(CONFIG_BOARD_SPECIFIC_LED)
 199 /* led_id_t is unsigned long mask */
 200 typedef unsigned long led_id_t;
 201
 202 extern void __led_toggle (led_id_t mask);
 203 extern void __led_init (led_id_t mask, int state);
 204 extern void __led_set (led_id_t mask, int state);
 205 #else
 206 # error Status LED configuration missing
 207 #endif
 208 /************************************************************************/
 209
 210 #ifndef CONFIG_BOARD_SPECIFIC_LED
 211 # include <asm/status_led.h>
 212 #endif
 213
 214 #endif  /* CONFIG_STATUS_LED    */
 215
 216 /*
 217  * Coloured LEDs API
 218  */
 219 #ifndef __ASSEMBLY__
 220 void coloured_LED_init(void);
 221 void red_led_on(void);
 222 void red_led_off(void);
 223 void green_led_on(void);
 224 void green_led_off(void);
 225 void yellow_led_on(void);
 226 void yellow_led_off(void);
 227 void blue_led_on(void);
 228 void blue_led_off(void);
 229 #else
 230         .extern LED_init
 231         .extern red_led_on
 232         .extern red_led_off
 233         .extern yellow_led_on
 234         .extern yellow_led_off
 235         .extern green_led_on
 236         .extern green_led_off
 237         .extern blue_led_on
 238         .extern blue_led_off
 239 #endif
 240
 241 #endif  /* _STATUS_LED_H_       */