src/arm/intel/ixp/intel-ixp42x-gateworks-gw2348.dts

   1 // SPDX-License-Identifier: ISC
   2 /*
   3  * Device Tree file for the Gateworks Avila GW2348 board.
   4  * This machine is based on IXP425.
   5  */
   6
   7 /dts-v1/;
   8
   9 #include "intel-ixp42x.dtsi"
  10 #include <dt-bindings/input/input.h>
  11
  12 / {
  13         model = "Gateworks Avila GW2348";
  14         compatible = "gateworks,gw2348", "intel,ixp42x";
  15         #address-cells = <1>;
  16         #size-cells = <1>;
  17
  18         memory@0 {
  19                 device_type = "memory";
  20                 reg = <0x00000000 0x4000000>;
  21         };
  22
  23         chosen {
  24                 bootargs = "console=ttyS0,115200n8";
  25                 stdout-path = "uart0:115200n8";
  26         };
  27
  28         aliases {
  29                 serial0 = &uart0;
  30         };
  31
  32         leds {
  33                 compatible = "gpio-leds";
  34                 led-user {
  35                         label = "gw2348:green:user";
  36                         gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
  37                         default-state = "on";
  38                         linux,default-trigger = "heartbeat";
  39                 };
  40         };
  41
  42         i2c {
  43                 compatible = "i2c-gpio";
  44                 sda-gpios = <&gpio0 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
  45                 scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
  46                 #address-cells = <1>;
  47                 #size-cells = <0>;
  48
  49                 hwmon@28 {
  50                         compatible = "adi,ad7418";
  51                         reg = <0x28>;
  52                 };
  53                 rtc: ds1672@68 {
  54                         compatible = "dallas,ds1672";
  55                         reg = <0x68>;
  56                 };
  57                 eeprom@51 {
  58                         compatible = "atmel,24c08";
  59                         reg = <0x51>;
  60                         pagesize = <16>;
  61                         size = <1024>;
  62                         read-only;
  63                 };
  64         };
  65
  66         soc {
  67                 bus@c4000000 {
  68                         flash@0,0 {
  69                                 compatible = "intel,ixp4xx-flash", "cfi-flash";
  70                                 bank-width = <2>;
  71                                 /* Enable writes on the expansion bus */
  72                                 intel,ixp4xx-eb-write-enable = <1>;
  73                                 /* 16 MB of Flash mapped in at CS0 */
  74                                 reg = <0 0x00000000 0x1000000>;
  75
  76                                 partitions {
  77                                         compatible = "redboot-fis";
  78                                         /* Eraseblock at 0x0fe0000 */
  79                                         fis-index-block = <0x7f>;
  80                                 };
  81                         };
  82                         ide@1,0 {
  83                                 compatible = "intel,ixp4xx-compact-flash";
  84                                 /*
  85                                  * Set up expansion bus config to a really slow timing.
  86                                  * The CF driver will dynamically reconfigure these timings
  87                                  * depending on selected PIO mode (0-4).
  88                                  */
  89                                 intel,ixp4xx-eb-t1 = <3>; // 3 cycles extra address phase
  90                                 intel,ixp4xx-eb-t2 = <3>; // 3 cycles extra setup phase
  91                                 intel,ixp4xx-eb-t3 = <15>; // 15 cycles extra strobe phase
  92                                 intel,ixp4xx-eb-t4 = <3>; // 3 cycles extra hold phase
  93                                 intel,ixp4xx-eb-t5 = <15>; // 15 cycles extra recovery phase
  94                                 intel,ixp4xx-eb-cycle-type = <0>; // Intel cycle type
  95                                 intel,ixp4xx-eb-byte-access-on-halfword = <1>;
  96                                 intel,ixp4xx-eb-mux-address-and-data = <0>;
  97                                 intel,ixp4xx-eb-ahb-split-transfers = <0>;
  98                                 intel,ixp4xx-eb-write-enable = <1>;
  99                                 intel,ixp4xx-eb-byte-access = <1>;
 100                                 /* First register set is CMD second is CTL (notice it uses CS2) */
 101                                 reg = <1 0x00000000 0x1000000>, <2 0x00000000 0x1000000>;
 102                                 interrupt-parent = <&gpio0>;
 103                                 interrupts = <12 IRQ_TYPE_EDGE_RISING>;
 104                         };
 105                         /*
 106                          * FIXME: Latch LEDs or extra UARTs at CS4
 107                          */
 108                 };
 109
 110                 pci@c0000000 {
 111                         status = "okay";
 112
 113                         /*
 114                          * Taken from Avila PCI boardfile.
 115                          *
 116                          * We have up to 4 slots (IDSEL) with 4 swizzled IRQs.
 117                          */
 118                         #interrupt-cells = <1>;
 119                         interrupt-map-mask = <0xf800 0 0 7>;
 120                         interrupt-map =
 121                         /* IDSEL 1 */
 122                         <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
 123                         <0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 10 */
 124                         <0x0800 0 0 3 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 9 */
 125                         <0x0800 0 0 4 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
 126                         /* IDSEL 2 */
 127                         <0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
 128                         <0x1000 0 0 2 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
 129                         <0x1000 0 0 3 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 8 */
 130                         <0x1000 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 2 is irq 11 */
 131                         /* IDSEL 3 */
 132                         <0x1800 0 0 1 &gpio0 9  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 3 is irq 9 */
 133                         <0x1800 0 0 2 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 3 is irq 8 */
 134                         <0x1800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 3 is irq 11 */
 135                         <0x1800 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 3 is irq 10 */
 136                         /* IDSEL 4 */
 137                         <0x2000 0 0 1 &gpio0 8  IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 4 is irq 8 */
 138                         <0x2000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 4 is irq 11 */
 139                         <0x2000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 4 is irq 10 */
 140                         <0x2000 0 0 4 &gpio0 9  IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 4 is irq 9 */
 141                 };
 142
 143                 /* EthB */
 144                 ethernet@c8009000 {
 145                         status = "okay";
 146                         queue-rx = <&qmgr 3>;
 147                         queue-txready = <&qmgr 20>;
 148                         phy-mode = "rgmii";
 149                         phy-handle = <&phy0>;
 150
 151                         mdio {
 152                                 #address-cells = <1>;
 153                                 #size-cells = <0>;
 154
 155                                 phy0: ethernet-phy@0 {
 156                                         reg = <0>;
 157                                 };
 158
 159                                 phy1: ethernet-phy@1 {
 160                                         reg = <1>;
 161                                 };
 162                         };
 163                 };
 164
 165                 /* EthC */
 166                 ethernet@c800a000 {
 167                         status = "okay";
 168                         queue-rx = <&qmgr 4>;
 169                         queue-txready = <&qmgr 21>;
 170                         phy-mode = "rgmii";
 171                         phy-handle = <&phy1>;
 172                 };
 173         };
 174 };